# Dowty Aerospace Service Bulletin A33/34-32-283

Copy: No revision named ("SB A33-34-32-283 R01"), 16 pages: PDF https://openairdocs.org/files/sha256/36/e4/36e45a3072895fc2d3cc4b3c29216d0b8f631bef6364764ac819b150cb5cdeca; text https://openairdocs.org/service-documents/dowty-aerospace/a33-34-32-283/file/36e45a307289.md. Rights: © Dowty Aerospace. Filed by the FAA in regulations.gov docket FAA-2013-0828, the docket of AD 2016-18-07. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Dowty Aerospace](https://openairdocs.org/service-documents/dowty-aerospace.md)
- Type: Service bulletin (Service Bulletin)
- Number: A33/34-32-283
- Page: https://openairdocs.org/service-documents/dowty-aerospace/a33-34-32-283

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/dowty-aerospace/a33-34-32-283/proposed.md).

## Text (16 pages)

Rights: © Dowty Aerospace. Filed by the FAA in regulations.gov docket FAA-2013-0828, the docket of AD 2016-18-07. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin No. A33/34-32-283
Page 1 of 10
CAGE: K0654
Cheltenham Road, Gloucester, GL2 9QH, England
Telephone: +44 (0) 1452 712424 Fax: +44 (0) 1452 713821
SERVICE BULLETIN
Messier-Dowty Ltd
 ©MESSIER-BUGATTI-DOWTY 2012 (AND SUBSEQUENT REVISION PAGE DATES)
This document and all information contained herein is the sole pr operty of Messier-Bugatti-Dowty. No intellectual property righ ts are
granted by the delivery of this document or the disclosure of its content. This document shall not be reproduced to a third party without the
express written consent of Messier-Bugatti-Dowty.
Safran and Messier-Bugatti names are marks owned respectively by  Safran and Messier-Bugatti-Dowty companies. The mark Dowty is
used under licence.
LANDING GEAR - MAIN LANDING GEAR - BOGIE AND DRESSINGS - INTRODUCTION OF A NEW 
BOGIE AND DRESSINGS WITH A NEW TWO COAT PAINT PROCEDURE
1. Planning Information
A. Effectivity
Aircraft affected: AIRBUS A330 and A340  Enhanced
Unit affected: Main Landing Gear Complete
which includes:
Bogie and Dressings
which includes:
Bogie Assembly
Part/Type Nos.: 10-210101 Series (Main Landing Gear Complete LH)
10-210201 Series (Main Landing Gear Complete RH)
which includes:
10-211501 Series (Bogie and Dressings)
which includes:
10-211701 Series (Bogie Assembly)
B. Concurrent Requirements
(1) None.
C. Reason
(1) Fracture of a bogie beam has occured in-service due to corrosion in the bore.
Investigation showed thin paint coats and paint deterioration.
D. Description
(1) Messier-Dowty Limited tells operators that a new bogie and dressings is introduced.
The new bogie and dressings has:
- a new two coat paint procedure applied
- the bogie beam protective treatments chec ked for thickness after they are applied
- a new protective treatment Ardrox AV100D applied to the bore of the bogie beam
after paint
- a new part number bogie beam, bogie beam subassembly and bogie beam, axle
and spacer subassembly. The new part numbers  will show that the two coat paint
procedure and Ardrox AV100D are applied and the protective treatments checked
for thickness.
May 11/2010
Jul 10/2012 (Revision 1)

### Page 2

Service Bulletin No. A33/34-32-283
Page 2
SERVICE BULLETIN
Messier-Dowty Ltd
(2) Messier-Dowty Limited recommend that yo u do this Service Bulletin on main landing
gears on which:
- the strike number 2 has not been canc elled on the bogie and dressings nameplate
and looks like this .
(3) Messier-Dowty Limited tells you that new m anufacture will include this Service Bulletin
on main landing gears on which:
- the strike number 2 has been cancel led on the bogie and dressings nameplate and
looks like this 
- the part number of the new main landing gear complete starts 10-210101-004 LH
and 10-210201-004 RH
- the part number of the new bogie and dressings starts 10-211501-001.
(4) Messier-Dowty Limited tells operators to re-identify, in-service, bogie beams that by
records have had the correct protective treatments applied and checked at new
manufacture.
(a) Appendix A of this Service Bulletin has the serial numbers of the bogie beams
which have had the correct protective treatments applied.
NOTE: If you have a bogie beam which has a serial number shown in the
table in Appendix A, you must re-identify the bogie beam, the bogie
assembly and the bogie beam, axle and spacer subassembly: refer
to Para 3.A. of this Service Bulletin.
E. Compliance
(1) Recommended
(a) At next overhaul.
(2) Refer to Airbus Service Bulletins A330-32-3237 and A340-32-4279.
F. Approval
(1) The technical content of this Service Bulletin has been approved under the authority of
the EASA Design Organisation Approval No. EASA.21J.031.
G. Manpower
(1) Messier-Dowty Limited make an estimate th at it will take approximately 3 man-hours to
identify each bogie beam with a new part number: refer to Para 3.A. 
(2) Messier-Dowty Limited tells you no more  man hours are necessary when you do this
Service Bulletin at overhaul or shop visit.
NOTE: It is assumed that the equipment has been placed in a maintenance
status. The man-hour estimates do not include preparation, close out or
administrative functions.
H. Weight and Balance
(1) None.
 2 
 2
Jul 10/2012 (Revision 1)

### Page 3

Service Bulletin No. A33/34-32-283
Page 3
SERVICE BULLETIN
Messier-Dowty Ltd
I. References
(1) Messier-Dowty Limited Component Maintenance Manual 32-12-60.
(2) Messier-Dowty Limited Component Maintenance Manual 32-12-63.
(3) Messier-Dowty Limited Component Maintenance Manual 32-12-64.
(4) Messier-Dowty Limited Modifica tion Form No. MAF1-0002-0149, issue 3.
(5) Messier-Dowty Standard Practices Manual 20-00-10.
(6) Airbus Service Bulletin A330-32-3237 and A340-32-4279.
(7) Airbus Modification No. 58896.
(8) Airbus Airworthiness Limitation Section Part 1.
(9) Aircraft Maintenance Manual.
NOTE: This Service Bulletin is subject of aircraft modification No. 58896 and is
covered by aircraft Service Bulletins A330-32-3237 and A340-32-4279. When
you do this Service Bulletin the modified equipment can not be installed on
the aircraft type unless the related aircraft modification and, if applicable, its
aircraft Service Bulletin are approved.
J. Other Publications Affected
(1) Messier-Dowty Limited Component Maintenance Manual 32-12-60.
(2) Messier-Dowty Limited Component Maintenance Manual 32-12-63.
(3) Messier-Dowty Limited Component Maintenance Manual 32-12-64.
2. Material Information
A. Material - Price and Availability
(1) The prices shown in this material section are valid for the calendar year, ending
December 31st 2012. Refer to the Messier-Dowty Spare Parts Price Catalog for
subsequent year prices or contact your regional Messier-Dowty Technical Assistance
and Spares Support Center (TASSC) for the latest price and availability information.
B. Material Necessary For Each Unit
The I/D codes below give information which help you to understand the
instruction/disposition.
I/D Code Instruction/information
AN e w  p a r t
B Part that can be obtained from the old one
C Expendable part
D Old part to be discarded
E Part of new design valid for new manufacture
F Part number change only
Jul 10/2012 (Revision 1)

### Page 4

Service Bulletin No. A33/34-32-283
Page 4
SERVICE BULLETIN
Messier-Dowty Ltd
Interchangeability codes (IC) given below show basic information to help you understand the
interchangeability of parts. For full explanation of interchangeability codes, please refer to
the latest edition of ATA specification 2000.
IC Instruction/information
01 One-way interchangeable
02 Two-way interchangeable
03 Not interchangeable
04 Interchangeable as a set
05 Qualified Interchangeability
The table that follows tells operators of the items that are necessary to do this Service
Bulletin. It does not include tools or materials that are referred to in the Component
Maintenance Manuals. 
C. Tooling
(1) None.
New
Part No.
Qty. 
Per 
Unit
Keyword Old
Part No.
Instructions/
Disposition
IC New 
Part 
Price 
($US)
10-210101-004 1 Main Landing Gear 
Complete LH
10-210101-003 (F) 01 -
OR
10-210201-004 1 Main Landing Gear 
Complete RH
which includes:
10-210201-003 (F) 01 -
10-211501-001 1 .Bogie and Dressings
which includes:
10-211501-000 (F) 01 -
10-211701-001 1 ..Bogie Assembly
which includes:
10-211701-000 (F) 01 -
30-2117004-01 1 ...Bogie Beam, Axle and 
Spacer Subassembly
which includes:
30-2117004-00 (F) 01 -
30-2117002-01 1 ....Bogie Beam 
Subassembly
which includes:
30-2117002-00 (F) 01 -
50-2117002-01 1 .....Bogie Beam 50-2117002-00 (B) 01 -
NOTE: For IC code also refer to Airbus Service Bulletins A330-32-3237 and
A340-32-4279.
Jul 10/2012 (Revision 1)

### Page 5

Service Bulletin No. A33/34-32-283
Page 5
SERVICE BULLETIN
Messier-Dowty Ltd
3. Accomplishment Instructions
The figure/item numbers in parentheses in the text  agree with those that are in the illustrated
parts list. Only the primary figure/item number s are used. The Process Specifications (M-DLPS,
M-DLNDT and PCS) are in the Standard Practices Manual.
A. Procedure to re-identify the bogie beam with a new part number, that by records have had
the correct protective treatments applied and checked at new manufacture (refer to the
Aircraft Maintenance Manual and CMM 32-12-64)
(1) Refer to Appendix A. Check the table in Appendix A for the serial numbers of the bogie
beams which, by records, have had the co rrect protective treatments applied and
checked at new manufacture. If a bogie beam serial number is shown in the table in
Appendix A:
NOTE: If a bogie beam serial number is not shown in the table in Appendix A:
refer to Para 3.B. 
(a) Make sure the aircraft is in a safe condition: refer to the Aircraft Maintenance
Manual.
(b) Remove the protective treatments from the bogie beam adjacent to the part
number: refer to PCS-2700.
(c) Identify the bogie beam (3-190) by chan ge of part number as follows: refer to
PCS-6000-05.
New Part Number Old Part Number
50-2117002-01 50-2117002-00
(d) Repair the protective treatment on top of the new part number: refer to PCS-2141
and PCS-2500.
(e) Identify the bogie beam subassembly (3-30)  by change of part number as follows:
refer to PCS-6000-07.
New Part Number Old Part Number
30-2117002-01 30-2117002-00
(f) Identify the bogie beam, axle and spacer  subassembly (2-190) by change of part
number as follows: refer to PCS-6000-07.
New Part Number Old Part Number
30-2117004-01 30-2117004-00
(2) Continue at Para 3.C. Identification.
B. Procedure at overhaul (refer to CMM 32-12-64 and Figures 1 to 2 of this Service Bulletin). At
the applicable step:
(1) Check that you have the correct thicknes s of cadmium plate. Measure at each point
(points 1 to 10), with a permascope, five times and take the average measurement:
refer to Figure 1 and 2 for the location of the measuring points.
Jul 10/2012 (Revision 1)

### Page 6

Service Bulletin No. A33/34-32-283
Page 6
SERVICE BULLETIN
Messier-Dowty Ltd
(a) The thickness of cadmium plate to be between 0,010 and 0,020 mm (0.0004 and
0.0008 in).
NOTE: If the measurement is below that given above, the bogie beam
must be cadmium plated again: refer to REPAIR and PCS-2100.
(2) Identify the bogie beam (3-190) by change of part number as follows: refer to
PCS-6000-05.
New Part Number Old Part Number
50-2117002-01 50-2117002-00
(3) Repair the protective treatment on top of the new part number: refer to PCS-2141 or
PCS-2100.
(4) Primer paint the bogie beam 50-2117002-01: refer to REPAIR and PCS-2500.
(5) Check that you have the correct thicknes s of primer paint. Measure at each point
(points 1 to 10), with a permascope, five times and take the average measurement:
refer to Figure 1 and 2 for the location of the measuring points.
(a) The thickness of primer paint in the bore of the bogie beam (points 1 to 8) to be
0,040 to 0,050 mm (0.0016 to 0.0020 in) dry film thickness.
(b) The thickness of primer paint on the outside of the bogie beam (points 9 and 10)
to be 0,020 to 0,025 mm (0.0008 to 0.0010 in) dry film thickness.
NOTE: The thickness measurement of the primer paint must not include
the cadmium plate thickness. The average thickness at Para
3.B.(1)(a) at points 1 to 10 must be subtracted from the thickness at
Para 3.B.(5)(a) and (b).
NOTE: If the measurement is below that given in Para 3.B.(5)(a) and (b) the
bogie beam must be primer painted again: refer to REPAIR and
PCS-2500.
(6) Install the bushes in the bogie beam 50-2117002-01: refer to ASSEMBLY .
(7) Top coat paint the bogie beam subassembly (3-30): refer to REPAIR, PCS-2500 and
PCS-7204.
(8) Check that you have the correct thickness of top coat paint. Measure at each point
(points 1 to 10), with a permascope, five times and take the average measurement:
refer to Figure 1 and 2 for the location of the measuring points.
(a) The thickness of top coat paint to be 0,040 to 0,050 mm (0.0016 to 0.0020 in) dry
film thickness.
NOTE: The thickness measurement of the top coat paint must not include
the cadmium plate or primer paint thicknesses. The average
thickness at Para 3.B.(1)(a) at points 1 to 10 plus the average
thicknesses taken at Para 3.B.(5)(a) and (b) at points 1 to 10 must
be subtracted from the thickness at Para 3.B.(8)(a). 
NOTE: If the measurement is below that given in Para 3.B.(8)(a), the bogie
beam subassembly must be painted again: refer to REPAIR and
PCS-2500.
Jul 10/2012 (Revision 1)

### Page 7

Service Bulletin No. A33/34-32-283
Page 7
SERVICE BULLETIN
Messier-Dowty Ltd
(9) Calculate the total thickness of protecti ve treatments applied (ie: cadmium plate plus
primer paint plus top coat paint). Measure the depth of protective treatments with a
permascope to make sure the total depth is correct.
(10) Apply Ardrox AV100D to the bore of the bogie beam subassembly (3-30): refer to
PCS-2800.
(11) Identify the bogie beam subassembly (3-30) by change of part number as follows: refer
to PCS-6000-07.
New Part Number Old Part Number
30-2117002-01 30-2117002-00
(12) Install the axles in the bogie beam subassembly 30-2117002-01 and install the spacers
on the axles: refer to ASSEMBLY.
(13) Identify the bogie beam, axle and spacer subassembly (2-190) by change of part
number as follows: refer to PCS-6000-07.
New Part Number Old Part Number
30-2117004-01 30-2117004-00
(14) Continue with the assembly of the bogi e assembly: refer to ASSEMBLY in the CMM.
C. Identification
NOTE: When it is necessary to replace the identification nameplate identify the
replacement nameplate with all the applicable data.
(1) After you have done this Service Bulletin:
- cancel the related strike number 2 on the bogie and dressings nameplate, refer to
M-DLPS1006-5  and cancel like this 
- write the Service Bulletin number A33/34-32-283 in the applicable aircraft and
landing gear records.
 2
Jul 10/2012 (Revision 1)

### Page 8

Service Bulletin No. A33/34-32-283
Page 8
SERVICE BULLETIN
Messier-Dowty Ltd
Bogie Beam - Measurement Points
Figure 1
A340A5239-1
A
A
80,00 to 90,00mm
(3.150 to 3.543in)
75,00 to 85,00mm
(2.953 to 3.346in)
80,00 to 90,00mm
(3.150 to 3.543in)
75,00 to 85,00mm
(2.953 to 3.346in)
POINT 9
POINT 10
POINTS 9 AND 10
ARE EXTERNAL
MEASUREMENT 
POINTS
B
100,00mm
(3.937in)
POINT 2
POINT 4
C
POINT 3POINT 4
POINT 1
POINT 5POINT 6
171,00mm
(6.732in)
171,00mm
(6.732in)
100,00mm
(3.937in)
B
POINT 8 POINT 7
SECTION A-A
POINTS 1 TO 8 
ARE INTERNAL 
MEASUREMENT 
POINTS
SEE SHEET
2
POINTS 1 TO 8 
ARE INTERNAL 
MEASUREMENT 
POINTS
Jul 10/2012 (Revision 1)

### Page 9

Service Bulletin No. A33/34-32-283
Page 9
SERVICE BULLETIN
Messier-Dowty Ltd
Bogie Beam - Measurement Points
Figure 2
A340A5240-1
SPOT FACES
PROBE DIAMETER
8,00 to 12,00mm
(0.315 to 0.472in)
TYPICAL ALL POINTS
SECTION B-B
W
POINT 1
POINT 2 DIAMETRICALLY OPPOSITE
POINT 3
POINT 4 DIAMETRICALLY OPPOSITE
POINT 5
POINT 6 DIAMETRICALLY OPPOSITE
POINT 7
POINT 8 DIAMETRICALLY OPPOSITE
V YSPOTFACES
DETAIL C
11,00mm
(0.433in)
POINTS 
3 TO 6
RADIUS
BLEND
TANGENT
POINT
SEE SHEET 1
TYPICAL POINTS
3 TO 6 INCLUSIVE
SEE SHEET 1
10,00mm
(0.390in) DIA X V-W
10,00mm
(0.390in) DIA Z V-W
10,00mm
(0.390in) DIA Z V-W
10,00mm
(0.390in) DIA Y V-W
X
Z
POINTS 1 TO 8 ARE INTERNAL 
MEASUREMENT POINTS
Jul 10/2012 (Revision 1)

### Page 10

Service Bulletin No. A33/34-32-283
Page 10
SERVICE BULLETIN
Messier-Dowty Ltd
4. Messier-Dowty and Messier Services Contacts
A. Refer to the Messier-Dowty website (safranmbd. com) for the latest list of contact names,
addresses and numbers. 
Original Equipment Manufacturers
Messier-Dowty Inc.
574 Monarch Avenue
Ajax, Ontario
L1S 2G8 
CANADA
Tel: 905-683-3100
Fax: 905-683-6936
Messier-Dowty Limited
Cheltenham Road
Gloucester
GL2 9QH
ENGLAND
Tel: +44(0)1452 712424
Fax: +44(0)1452 713821
Messier-Bugatti-Dowty 
Landing Gear & Systems 
Integration Division
Inovel Parc Sud
BP10
78140 Velizy - Villacoublay
FRANCE
Tel: +33 146 29 18 00
Fax: +33 146 29 8770
Technical Assistance and Spares Support Centers (TASSC)
For AOG (commercial and technical): aogtassc@safranmbd.com
For Europe - Africa - Middle East customers: eametassc@safranmbd.com
Tel: +33 1 5521 2590
For Americas customers: americatassc@safranmbd.com
Tel: +1 404 305 2626
For Asia-Pacific customers: asiatassc@safranmbd.com
Tel: +65 6245 5688
Repair and Overhaul Facilities
Messier Services R&O Facility
574 Monarch Avenue
Ajax, Ontario
L1S 2G8
CANADA
Tel: 905-683-3100
Fax: 905-683-0378
Messier Services R&O Facility
Meteor Business Park
Cheltenham Road
Gloucester GL2 9QL
ENGLAND
Tel: +44(0)1452 713111
Fax: +44(0)1452 716500
Messier Services R&O Facility
3, rue Antoine de St Exupery, 
BP110
67124 Molsheim Cedex
FRANCE
Tel: (33) 38838 9200
Fax: (33) 38838 9399
Messier Services (Asia) Pte. Ltd. 
R&O Facility
21 Loyang Crescent, 
Loyang Industrial Estate
SINGAPORE 508985
Tel: (65) 6545 9455
Fax: (65) 6542 3936
Messier Services R&O Facility - 
Americas
Av. La Noria
Parque Industrial Querétaro
Carretera QRO-SLP, Km. 28.5
Querétaro, QRO 76220
MEXICO
Tel: +52 (442) 19 25 800
Fax:+52 (442) 19 25 801
HYDREP Aéroport de 
Dinard-Pleurtuit-Saint-Malo
Bâtiment 20
BP90154
35801 DINARD Cedex
FRANCE
Tel: (33) 2 99 82 79 79
Fax: (33) 2 99 82 79 97
Jul 10/2012 (Revision 1)

### Page 11

Appendix A
Service Bulletin No. A33/34-32-283
Page 1 of 4
CAGE: K0654
Cheltenham Road, Gloucester, GL2 9QH, England
Telephone: +44 (0) 1452 712424 Fax: +44 (0) 1452 713821
SERVICE BULLETIN
Messier-Dowty Ltd
 ©MESSIER-BUGATTI-DOWTY 2012 (AND SUBSEQUENT REVISION PAGE DATES)
This document and all information contained herein is the sole pr operty of Messier-Bugatti-Dowty. No intellectual property righ ts are
granted by the delivery of this document or the disclosure of its content. This document shall not be reproduced to a third party without the
express written consent of Messier-Bugatti-Dowty.
Safran and Messier-Bugatti names are marks owned respectively by  Safran and Messier-Bugatti-Dowty companies. The mark Dowty is
used under licence.
APPENDIX A
LANDING GEAR - MAIN LANDING GEAR - BOGIE AND DRESSINGS - BOGIE BEAM -
SERIAL NUMBER DATA
1. The tables that follow shows the serial numbers of the bogie beams 50-2117002-00 that have had
the correct protective treatments applied and checked at new manufacture.      
Bogie Beam Serial No. Bogie Beam Serial No. B ogie Beam Serial No. Bogie Beam Serial No.
07MDG10904  07MDG10905 07MDG10906 07MDG10907
07MDG10909 07MDG10912 07MDG10913 07MDG10916
07MDG10917 07MDG10918 07MDG10920 07MDG12582
07MDG12583 07MDG12584 07MDG12585 07MDG12586
07MDG12589 07MDG12590 07MDG12591 07MDG12592
07MDG12593 07MDG12594 07MDG12595 07MDG12596
07MDG15298 07MDG15299 07MDG15300 07MDG15301
07MDG15302 07MDG15303 07MDG15304 07MDG15305
07MDG15306 07MDG15307 07MDG15422 07MDG15423
07MDG15424 07MDG15425 07MDG15426 07MDG16096
07MDG16097 07MDG16098 07MDG16099 07MDG16100
07MDG16101 07MDG16429 07MDG16430 07MDG16431
07MDG16432 07MDG16433 07MDG16434 07MDG16438
07MDG16468 07MDG16469 07MDG16470 07MDG16471
07MDG16472 07MDG16473 07MDG16474 07MDG16475
07MDG16476 07MDG16477 07MDG18792 07MDG18793
07MDG18794 07MDG18795 07MDG18796 07MDG18797
08MDG1054 08MDG1055 08MDG1056 08MDG1057
08MDG1058 08MDG1059 08MDG3114 08MDG3115
08MDG3116 08MDG3117 08MDG3118 08MDG3119
Jul 10/2012 (Revision 1)

### Page 12

Appendix A
Service Bulletin No. A33/34-32-283
Page 2
SERVICE BULLETIN
Messier-Dowty Ltd
08MDG3120 08MDG3121 08MDG3122 08MDG3123
08MDG3508 08MDG3509 08MDG3510 08MDG3511
08MDG3512 08MDG3513 08MDG3514 08MDG3515
08MDG3516 08MDG3517 08MDG3541 08MDG3542
08MDG3543 08MDG3544 08MDG3545 08MDG3546
08MDG3744 08MDG3745 08MDG3944 08MDG3945
08MDG3946 08MDG3947 08MDG3948 08MDG3949
08MDG3974 08MDG3975 08MDG5512 08MDG5513
08MDG5514 08MDG5515 08MDG5516 08MDG5517
08MDG5518 08MDG5519 08MDG5936 08MDG5937
08MDG5938 08MDG5939 08MDG7898 08MDG7899
08MDG7900 08MDG7901 08MDG7902 08MDG7903
08MDG7904 08MDG7905 08MDG7907 08MDG7908
08MDG9812 08MDG9813 08MDG9828 08MDG9829
08MDG9830 08MDG9831 08MDG9832 08MDG9833
08MDG9834 08MDG9835 08MDG9850 08MDG9851
08MDG9852 08MDG9853 08MDG9854 08MDG9855
08MDG9856 08MDG9857 08MDG9858 08MDG9859
08MDG9860 08MDG9861 08MDG9962 08MDG9963
08MDG9964 08MDG9965 08MDG9966 08MDG9967
08MDG9982 08MDG9983 08MDG9984 08MDG9985
08MDG11596 08MDG11597 08MDG11598 08MDG11599
08MDG11600 08MDG11601 08MDG14819 08MDG14820
08MDG14821 08MDG14822 08MDG14823 08MDG14969
08MDG14970 08MDG14971 08MDG14973 08MDG14974
08MDG14975 08MDG14976 08MDG14979 08MDG14980
09MDG2103 09MDG2104 08MDG12359 09MDG2100
08MDG14977 08MDG12355 09MDG2102 09MDG2105
08MDG12356 08MDG12358 09MDG2101 08MDG12357
Bogie Beam Serial No. Bogie Beam Serial No. B ogie Beam Serial No. Bogie Beam Serial No.
Jul 10/2012 (Revision 1)

### Page 13

Appendix A
Service Bulletin No. A33/34-32-283
Page 3
SERVICE BULLETIN
Messier-Dowty Ltd
08MDG5966 08MDG14161 08MDG12361 08MDG12362
08MDG14166 08MDG14162 08MDG12360 08MDG14163
08SPP0001 08SPP0002 08SPP0003 08SPP0004
08SPP0005 08SPP0006 08SPP0007 08SPP0008
08SPP0009 08SPP0010 08SPP0011 08SPP0012
08SPP0013 08SPP0014 08SPP0015 08SPP0016
08SPP0017 08SPP0018 08SPP0019 08SPP0020
08SPP0021 08SPP0022 08SPP0023 08SPP0024
08SPP0025 08SPP0026 08SPP0027 08SPP0028
08SPP0029 08SPP0030 08SPP0031 08SPP0032
08SPP0033 08SPP0034 08SPP0035 08SPP0036
08SPP0037 08SPP0038 08SPP0039 08SPP0040
08SPP0041 08SPP0042 08SPP0043 08SPP0044
08SPP0045 08SPP0047 08SPP0048
08SPP0049 08SPP0050 08SPP0051 08SPP0052
08SPP0053 08SPP0054 08SPP0055 08SPP0056
08SPP0057 08SPP0058 08SPP0059 08SPP0060
08SPP0061 08SPP0062
08SPP0078
08SPP0079 08SPP0080 08SPP0081 08SPP0082
08SPP0083 - - -
07B0010X1995 08B0004X2015 08B0005X2019 08B0006X2085
08B0007X2087 08B0008X1993 08B0009X1994 08B0011X1996
08B0012X2153 08B0013X2154 08B0014X2155 08B0015X2173
08B0016X2054 08B0017X2170 08B0018X2169 08B0019X2088
08B0020X2028 08B0021X2029 08B0022X2030 08B0023X2031
08B0024X2053 08B0025X2247 08B0026X2248 08B0027X2249
Bogie Beam Serial No. Bogie Beam Serial No. B ogie Beam Serial No. Bogie Beam Serial No.
Jul 10/2012 (Revision 1)

### Page 14

Appendix A
Service Bulletin No. A33/34-32-283
Page 4
SERVICE BULLETIN
Messier-Dowty Ltd
08B0028X0026 08B0033X2309 08B0034X2270 08B0035X2276
08B0036X2277 08B0037X2256 08B0039X2295 08B0040X2308
08B0041X0002 08B0042X0003 08B0044X2315 08B0045X2317
08B0046X2318 08B0048X2342 08B0050X2338 08B0051X0014
08B0052X0007 08B0054X0005 08B0056X2395 08B0064X0018
08B0058X2405 08B0062X2419 08B0063X0015 08B0068X0028
08B0065X0019 08B0066X0020 08B0067X0021 08B0073X0042
08B0069X0008 08B0070X0029 08B0072X0031 09B0077X0079
09B0055X2345 09B0071X0030 09B0076X0059 08B0038X2294
09B0078X0084 08B0031X2224 08B0032X2227 09B0075X0058
08B0084X0123 09B0060X2407 09B0074X0065 09B0057X2396
09B0079X0088 09B0081X0071 – –
Bogie Beam Serial No. Bogie Beam Serial No. B ogie Beam Serial No. Bogie Beam Serial No.
Jul 10/2012 (Revision 1)

### Page 15

CAGE: K0654
Cheltenham Road, Gloucester, GL2 9QH, England
Telephone: +44 (0) 1452 712424 Fax: +44 (0) 1452 713821
SERVICE BULLETIN
Messier-Dowty Ltd
 ©MESSIER-BUGATTI-DOWTY 2012 (AND SUBSEQUENT REVISION PAGE DATES)
This document and all information contained herein is the sole pr operty of Messier-Bugatti-Dowty. No intellectual property righ ts are
granted by the delivery of this document or the disclosure of its content. This document shall not be reproduced to a third party without the
express written consent of Messier-Bugatti-Dowty.
Safran and Messier-Bugatti names are marks owned respectively by  Safran and Messier-Bugatti-Dowty companies. The mark Dowty is
used under licence.
AIRBUS A330/A340 MAIN LANDING GEAR
SERVICE BULLETIN A33/34-32-283
TRANSMITTAL LETTER FOR REVISION 1
DATE JUL 10/2012
1. REASON
A. To update Manpower hours.
B. To update serial numbers in Appendix A.
2. ACTION
A. Remove and destroy existing pages 1 to 10 and substitute revised pages 1 to 10
dated Jul 10/2012.
B. Appendix A. Remove and destroy existing pages 1 to 4 and substitute revised pages 1 to 4
dated Jul 10/2012.
3. PREVIOUS REVISION/ISSUE DETAILS
Revision Status Date
A. Initial Issue May 11/2010

### Page 16

SERVICE BULLETIN
Messier-Dowty Ltd

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
