# Embraer Alert Service Bulletin 110-27-A095: No revision named

- Rights: © Embraer S.A. Filed by the FAA in regulations.gov docket FAA-2014-0740, the docket of AD 2014-20-05. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Embraer Alert Service Bulletin 110-27-A095](https://openairdocs.org/service-documents/embraer/110-27a095.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin 110-27-A095
- Pages: 16
- PDF: https://openairdocs.org/files/sha256/3e/93/3e93d694d052bb2aab232b83dbdf3167945db5bf7b92a13ee1c3545d1a08d934
- Page: https://openairdocs.org/service-documents/embraer/110-27a095/file/3e93d694d052

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

- EMBRAER  ALERT
SERVICE BULLETIN
in connection with the use of this document, Embraer does not provide any express or implied warranties and expressly disclaims any
warranty of merchantability or fitness for a particular purpose.
FLIGHT CONTROLS - INSPECTION OF THE RUDDER TRIM TAB ACTUATOR
1. PLANNING INFORMATION
A. SB EFFECTIVITY
Aircraft affected:
MODEL  SN
EMB-110 - BANDEIRANTE  All aircraft in operation equipped with the affected
Part Number.
Affected component:
Rudder Trim Tab Actuator Part Numbers 110P2-506-10-09-36, 110P2-506-10-09-37,
and 110P2-506-10-09-38 installed in the aircraft or in stock as spare.
NOTE: This effectivity list includes the aircraft originally equipped with the affected
component. Since this component is a "Line Replaceable Unit" (LRU), it may
be necessary to refer to the fleet maintenance control record and verify
whether the unit has not been replaced with another one during routine
maintenance.
In-production effectivity:
The subject presented in this bulletin does not affect any in-production aircraft.
B. CONCURRENT REQUIREMENTS
None.
REVISION No.:  DATE: 21/Aug/2014  ALERT  SB No.: 110-27-A095  PAGE: 1 of 15
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 2 (OCR)

- EMBRAER  ALERT
SERVICE BULLETIN
C. REASON
Embraer was informed about an event of high level vibration and difficulty of
controllability during an Embraer-110P1 flight that required the crew to do a forced
landing.
The investigation identified a condition of a severe internal at the rudder trim tab
actuator fork end, which was found disconnected, making the rudder trim tab loose.
Also, the rudder horn mass balance was lost.
This Alert Service Bulletin gives the instructions to inspect the rudder trim tab
actuator components for signs of corrosion, with emphasis on its spring and fork end.
D. DESCRIPTION
This Bulletin is divided into 2 PARTS, as follows:
PARTI  INSPECTION OF THE RUDDER TRIM TAB ACTUATOR COMPONENTS
Applicable to:  Service Bulletin Effectivity.
PART I of this bulletin presents a Detailed Inspection (DI) for signs of corrosion in the
Rudder Trim Tab Actuator components, specifically on its Spring and Fork End
installed in Rudder Trim Tab Actuator.
a) If no signs of corrosion in the Spring and Fork End are detected, the
components cleaning and protection against corrosion by the application of a
corrosion inhibitive compound is required;
b) If any signs of corrosion is detected in the Spring and Fork End, replace these
components by the accomplishment of Part Il of this Bulletin.
To do this, it is necessary to remove the Rudder Trim Tab Actuator from the aircraft
and perform the inspection on the bench.
NOTE: During the inspections mentioned in this PART I, the corrosion level
identification may be different depending on the component to be inspected.
The time for accomplishment of PART Il of this Bulletin is also different
depending on the level of the corrosion of each component. For this, refer to
Section 1.E. TIME FOR ACCOMPLISHMENT below for a detailed
instructions for corrosion level identification.
PAGE: 2  SB No.: 110-27-A095  ALERT  DATE: 21/Aug/2014  REVISION No.:
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 3 (OCR)

• EMBRAER  ALERT
SERVICE BULLETIN
Embraer is providing the necessary support for the accomplishment of this Bulletin
with the Embraer Technical Representatives or through Embraer Fleet Technical
Center. Refer to Section 2.B. INDUSTRY SUPPORT INFORMATION for Embraer
contact information.
PART II  REPLACEMENT OF THE SPRING AND FORK END
Applicable to:  Service Bulletin Effectivity.
PART Il of this bulletin consists in replacing the Spring and Fork End installed in
Rudder Trim Tab Actuator.
To do this, it is necessary to remove the Rudder Trim Tab Actuator from the aircraft
and perform the modification on the bench.
E. TIME FOR ACCOMPLISHMENT
(1) Applicable to PART I
Embraer recommends that PART I of this bulletin be accomplished within the next 10
flight hours or 15 calendar days, whichever occurs first, after the release date of this
Service Bulletin.
NOTE: If any report of vibration is detected, Embraer recommends the
accomplishment of PART I of this Service Bulletin before the next flight.
DATE: 21/Aug/2014  REVISION No.:  ALERT  SB No.: 110-27-A095  PAGE: 3
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 4 (OCR)

- EMBRAER  ALERT
SERVICE BULLETIN
(2) Applicable to PART II
(a) Applicable for the Fork End (Aluminum) - Internal and External surface
CORROSION  CORROSION  ACTION / TIME FOR
LEVEL  CARACTERIZATION  ACCOMPLISHMENT
Characterized by a surface color  - Clean the surface with
change different from the original Methyl Ethyl Ketone (MEK)
aspect. Normally these affected  apply Corrosion
areas present dark gray coloration. Inhibitor Compound Dinitrol
Visually examining the surface it is AV 15 or AV 30 (or any
Surface oxidation or  not possible to detect pitting under Spec. MIL-PRF-
discoloration  indications. When scribing the  16173) in the Fork End
affected surface with a suitable  Bore immediately after the
tool, it is possible to observe that  accomplishment of PART I
the indication is just superficial with  of this Bulletin.
no deep indication. Use suitable
tool like acrylic/plastic razor to
avoid scratches in the surface.
- Clean the surface with
Methyl Ethyl Ketone (MEK)
and apply Corrosion
Inhibitor Compound Dinitrol
AV 15 or AV 30 (or any
under Spec. MIL-PRF-
Light Corrosion  16173) in the Fork End
(Local pitting  Characterized by single pitting  Bore immediately after the
corrosion not  indications not concentrated in a  accomplishment of PART I
located in the cross  specific area and not located in the  of this Bulletin, and then;
hole boundaries)  cross holes boundaries.
- Replace the Fork End by
the accomplishment of
PART Il 150 flight hours or
03  calendar months
(whichever occurs first)
after the accomplishment of
PARTI.
Severe Corrosion  (Multiple pitting  Characterized by multiple  - Replace the Fork End by
corrosion or pitting  concentrated pitting indications in  accomplishment of
located in the cross  any surface of the part or by single  PART II of this Bulletin
hole boundary)  cross hole boundary.  pitting indication located in  immediately  accomplishment of PART I.
SB No.: 110-27-A095  ALERT  DATE: 21/Aug/2014
PAGE: 4  REVISION No.:
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 5 (OCR)

- EMBRAER  ALERT
SERVICE BULLETIN
(b) Applicable for the Spring (Steel)
CORROSION  CORROSION  ACTION / TIME FOR
LEVEL  CARACTERIZATION  ACCOMPLISHMENT
Characterized by a surface color  Clean the surface with
change different from the original  Methyl Ethyl Ketone (MEK)
aspect. Normally these affected to remove the residues and
areas present a reddish to brown apply Corrosion Inhibitor
Surface oxidation or  or dark coloration. When scribing  Compound Dinitrol AV 15
discoloration:  tool, it is possible to observe that  the affected surface with a suitable  or AV 30 (or any under  Spec. MIL-PRF-16173) in
the indication is just superficial the  Fork End Bore
without evidence of material immediately after the
removal. Use suitable tool like  accomplishment of PART I
acrylic/plastic razor to avoid of this Bulletin.
scratches in the surface.
Sand Smoothly the
affected areas, clean the
surface to remove the
Characterized by local reddish to  residues  and  apply
brown indications without evidence  Corrosion  Inhibitor
of thickness reduction. Scribing the  Compound Dinitrol AV 15
surface with a suitable tool it is  or AV 30 (or any under
possible to observe changes in the  Spec. MIL-PRF-16173) in
Light Corrosion:  indication area and surrounding  surface roughness between the  the spring immediately after  the accomplishment  of
surfaces, but there is no deep  PART I of this Bulletin, and
indication. Use suitable tool like  then.
scratches in the surface.  acrylic/plastic razor to avoid  - Replace the Spring by the  accomplishment of PART II
150 flight hours or 03
months (whichever occurs
first)  after  the
accomplishment of PART I
Characterized by overall reddish to
brown indications with evidence of
thickness reduction or residues
Severe Corrosion:  possible to observe deep  the surface with a suitable tool it is  due to material exfoliation. Scribing  accomplishment of PART II  of this Bulletin immediately  Replace the Spring by the
indications with evidence of  after the accomplishment of
thickness reduction. Use suitable  PARTI.
tool like acrylic/plastic razor to
avoid scratches in the surface.
REVISION No.:  DATE: 21/Aug/2014  ALERT  SB No.: 110-27-A095  PAGE: 5
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 6 (OCR)

-EMBRAER  ALERT
SERVICE BULLETIN
F. APPROVAL
The technical aspects of this Alert Service Bulletin are approved by: Embraer -
Engineering Board.
G. COMMUNICATIONS TO EMBRAER
EMBRAER requests that any results found during these inspections be informed to
your local EMBRAER representatives or offices.
H. ESTIMATED MANPOWER
This estimate is for direct labor only, performed by experienced personnel, and does
not include the time to plan, prepare, or inspect the work.
it is assumed that all the tools, parts, and other means are readily available when
necessary.
This estimate does not include the sealant, paint, or adhesive curing time.
-Access opening: 1.0 man- hour.
- Inspection: 1.5 man- hours.
-Modification: 3.0 man- hours.
-Access closure: 1.0 man- hour.
-Test: 1.0 man-hour.
I. WEIGHT AND BALANCE
-Change in basic weight: None.
-Change in basic moment: None.
J. REFERENCES
T.O. 1C95A-2-5 - "Maintenance Manual" - Flight Controls.
T.P. 27-00-01/702 - Component Maintenance Manual.
SB No.: 110-27-A095  PAGE: 6  ALERT  DATE: 21/Aug/2014  REVISION No.:
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 7 (OCR)

-EMBRAER  ALERT
SERVICE BULLETIN
K. OTHER PUBLICATIONS AFFECTED
None.
2. MATERIAL INFORMATION
A. MATERIAL - PRICE AND AVAILABILITY
(1) MATERIAL AVAILABLE FROM EMBRAER
None.
(2) MATERIAL AVAILABLE FROM OTHER VENDORS
None.
B. INDUSTRY SUPPORT INFORMATION
Embraer can provide the necessary support for the accomplishment of this Bulletin
with the Embraer Technical Representatives or through Return to Service.
See address below:
EMBRAER S.A.
ATT.: Return to Service - RTS.
Phone: +55 12 3927 7334 or +55 12 99121 2022.
E-mail: rts@embraer.com.br
REVISION No.:  DATE: 21/Aug/2014  ALERT  SB No.: 110-27-A095  PAGE: 7
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 8 (OCR)

-EMBRAER  ALERT
SERVICE BULLETIN
C. MATERIAL NECESSARY FOR EACH AIRCRAFT
(1) MATERIAL TO BE PROCURED - Applicable to Part Il only
(a) PARTS
The parts below should be ordered as spares from Embraer. For this, check
the Rudder Trim Tab Actuator Part Number before ordering the Parts.
Applicable for Rudder Trim Tab Actuator PN 110P2-506-10-09-36 and 110P2-
506-10-09-38
NEW PN  DESCRIPTION  OLD PN  QTY  DISP
110P2-506-10-09-28-03  Fork End  110P2-506-10-09-28-03  01  7
120-09954-001  Spring  120-09954-001  01  7
PE49073-1  Neoprene  Sleeve  PE49073-1  01  Tla
(a) Replace the Neoprene Sleeve only if it is damaged.
Applicable for Rudder Trim Tab Actuator PN 110P2-506-10-09-37
NEW PN  DESCRIPTION  OLD PN  QTY  DISP/
Note
110P2-506-10-09-29-02  Fork End  110P2-506-10-09-29-02  01  7
120-09954-001  Spring  120-09954-001  01  7
PE49073-1  Neoprene Sleeve  PE49073-1  01  71a
(a) Replace the Neoprene Sleeve only if it is damaged.
(b) CONSUMABLES
The material below or equivalent, required for the accomplishment of this
bulletin, should be procured from the operator's inventories or from a local
supplier.
ITEM PN  DESCRIPTION  QTY  DISP
Methyl Ethyl Ketone
(Spec. ASTM-D-740)  Solvent  AR  6
DINITROL AV-30
(Spec. MEP10-063)  Corrosion-inhibiting compound  AR  6
DINITROL AV-15  Corrosion-inhibiting compound  AR  6
Spec. MIL-PRF-16173  Corrosion-inhibiting compound  AR  6
SB No.: 110-27-A095  ALERT  DATE: 21/Aug/2014
PAGE: 8  REVISION No.:
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 9 (OCR)

TEMBRAER  ALERT
SERVICE BULLETIN
QUANTITY:
AR = As Required.
DISPOSITION:
6 = Apply as required
7 = Replace with part bearing same PN
D. MATERIAL NECESSARY FOR EACH SPARE
None.
E. REIDENTIFIED PARTS
None.
F. TOOLING - PRICE AND AVAILABILITY
None.
DATE: 21/Aug/2014  REVISION No.:  ALERT  SB No.: 110-27-A095  PAGE: 9
Copyright © 2014 by EMBRAER - All rights reserved

### Page 10 (OCR)

- EMBRAER  ALERT
SERVICE BULLETIN
3. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1) For the purpose of this Service Bulletin, a Detailed Inspection (DI) is: "An
intensive examination of a specific item, installation or assembly to detect
damage, failure or irregularity. Available lighting is normally supplemented
with a direct source of good lighting at an intensity deemed appropriate.
Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate access procedures may be
required."
2) Obey all of the WARNINGS and CAUTIONS included in the referenced
manuals and procedures.
3) The Manuals and other documents are referred to by means of acronyms
or using a simplified form. Refer to section "1. I. REFERENCES" for a
more complete definition.
The steps below outline the general accomplishment instructions.
The detailed sequence is included in the respective figure, when necessary.
A. Make sure that the aircraft is safe for maintenance.
B. PART I - INSPECTION OF THE RUDDER TRIM TAB ACTUATOR COMPONENTS
(1)  Remove the Rudder Trim Tab Actuator from the aircraft following the
instructions of T.O. 1C95A-2-5 - "Maintenance Manual" - Flight Controls.
On the Bench, disassemble the Rudder Trim Tab Actuator by following the
instructions mentioned in T.P. 27-00-01/702 - Component Maintenance Manual
with Illustrated Part List - Disassembly Section. Refer to Figure 1.
(3)  Clean the components with the aid of a nylon brush wet with Methyl Ethyl
Ketone (ASTM-D-740) MEK.
(4)  Do a Detailed Inspection in the Fork End and in the Spring for signs of
corrosion and then Refer to Table 1 and Table 2 to identify the applicable
action.
SB No.: 110-27-A095  ALERT  DATE: 21/Aug/2014
PAGE: 10  REVISION No.:
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 11 (OCR)

-EMBRAER  ALERT
SERVICE BULLETIN
(a) Applicable for the Fork End (Aluminum) - Internal and External surface
CORROSION LEVEL  ACTION
- After cleaning, apply a  corrosion inhibitor
Surface oxidation or  compound Dinitrol AV-15 or AV-30 (or any under
discoloration:  Spec. MIL-PRF-16173) in the Fork End bore.
Local pitting corrosion outside
the cross hole boundaries:
Multiple pitting corrosion or
pitting around the cross hole:
- After cleaning, apply a corrosion inhibitor
compound Dinitrol AV-15 or AV-30 (or any under
Spec. MIL-PRF-16173) in the Fork End bore;
- Replace the Fork End by the accomplishment of
PART Il of this SB in the next 150 flight hours or 03
months (whichever occurs first).
- Replace the Fork End by the accomplishment of
PART Il of this Bulletin immediately after the
accomplishment of PART I.
TABLE 01
(b) Applicable for the Spring (Steel)
CORROSION LEVEL  ACTION
- After cleaning, apply a corrosion inhibitor
Surface oxidation or  compound Dinitrol AV-15 or AV-30 (or any under
discoloration:  Spec. MIL-PRF-16173) in the Fork End bore.
- Sand smoothly the spring surface, clean the
surface using Methyl Ethyl Ketone or equivalent
and then apply Dinitrol AV-15 or AV-30 (or any
under Spec. MIL-PRF-16173) to the Spring surface
Light Corrosion:
- Replace the Spring by the accomplishment of
PART Il of this SB in the next 150 flight hours or 03
months (whichever occurs first).
Replace the Spring by the accomplishment of
Severe Corrosion:  PART Il of this Bulletin immediately after the
accomplishment of PART I.
TABLE 02
DATE: 21/Aug/2014  REVISION No.:  ALERT  SB No.: 110-27-A095  PAGE: 11
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 12 (OCR)

- EMBRAER  ALERT
SERVICE BULLETIN
Assembly the Rudder Trim Tab Actuator by following the instructions
mentioned in T.P. 27-00-01/702 - Component Maintenance Manual with
Illustrated Part List - Assembly Section.
NOTE 1: During the Assemble of the Rudder Trim Tab Actuator apply Dinitrol
AV-15 or AV-30 (or any under Spec. MIL-PRF-16173) inside the
terminal bore.
NOTE 2: If the neoprene sleeve PN PE49073-1 was found damaged, replace
it using a new neoprene sleeve with the same Part Number.
(6)  Reinstall the Rudder Trim Tab Actuator to the aircraft following the instructions
of T.O. 1C95A-2-5 - "Maintenance Manual" - Flight Controls.
NOTE: After reinstallation do an operation check-out and the trim tabs
maximum allowable backlash checkout as described in the
Maintenance Manual.
C. PART II - REPLACEMENT OF THE SPRING AND FORK END
(1)  Remove the Rudder Trim Tab Actuator from the aircraft.
On the Bench, disassembly the Rudder Trim Tab Actuator by following the
instructions mentioned in T.P. 27-00-01/702 - Component Maintenance Manual
with Illustrated Part List - Disassembly Section. Refer to Figure 1.
(3)  Replace the Fork End and/or Spring by the same Part Number.
(4)  Assemble the Rudder Trim Tab Actuator by following the instructions
mentioned in T.P. 27-00-01/702 - Component Maintenance Manual with
Illustrated Part List - Assembly Section. Refer to Figure 1.
NOTE 1: During the Assemble of the Rudder Trim Tab Actuator apply Dinitrol
AV-15 or AV-30 (or any under Spec. MIL-PRF-16173) inside the
terminal bore.
NOTE 2: If the neoprene sleeve PN PE49073-1 was found damaged, replace
it using a new neoprene sleeve with the same Part Number.
(5)  Reinstall the Rudder Trim Tab Actuator to the aircraft following the instructions
of T.O. 1C95-A-2-5 - "Maintenance Manual" - Flight Controls.
NOTE: After reinstallation do an operation check-out and the trim tabs
maximum allowable backlash checkout as described in the
Maintenance Manual.
PAGE: 12  SB No.: 110-27-A095  ALERT  DATE: 21/Aug/2014  REVISION No.:
Copyright © 2014 by EMBRAER - All rights reserved

### Page 13 (OCR)

- EMBRAER  ALERT
SERVICE BULLETIN
D. Put the aircraft back to a serviceable condition.
E. Enter Write the accomplishment of PART I and/or PART Il of this bulletin in the
applicable documents.
NOTES: 1) Please inform us by e-mail fleet.reliability@embraer.com.br of the aircraft
manufacturer serial number and the SB incorporation date, specifying the
SB Parts) incorporated or whether the whole SB has been incorporated.
This will enable Embraer to consider your aircraft configuration when
providing future modifications.
2) To formally inform that the SB has been incorporated fleetwide or that the
SB will not be incorporated, so that Embraer can update the affected
technical publications, use the Service Bulletin Full-Fleet Incorporation
Report" form, which is  available on the Flyembraer portal
(http://www.flyembraer.com).
3) Use the attached "Service Bulletin Evaluation" form to send us your
comments regarding this SB. Your feedback will be much appreciated as
an aid for us to improve the quality of the SBs.
DATE: 21/Aug/2014  REVISION No.:  ALERT  SB No.: 110-27-A095  PAGE: 13
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 14 (OCR)

- EMBRAER  ALERT
SERVICE BULLETIN
RUDDER TRIM
TAB ACTUATOR
ACCESS TO THE
RUDDER TRIM
TAB ACTUATOR
TRANSMITTAL
BOX
(REF.)
RUDDER TRIM
TAB ACTUATOR
(REMOVE AND REINSTALL)
DET. A
FIGURE 1: RUDDER TRIM TAB ACTUATOR INSPECTION
(SHEET 01 OF 02)
SB No.: 110-27-A095  ALERT  DATE: 21/Aug/2014
PAGE: 14  REVISION No.:
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 15 (OCR)

• EMBRAER  ALERT
SERVICE BULLETIN
FORK END
(INSPECT THE INTERNAL
AND EXTERNAL SURFACE)
FORK END
(INSPECT THE INTERNAL
AND EXTERNAL SURFACE)
NEGORENE SLEEVE
SPRING
(INSPECT)
DET. B
FORK END OF ACTUATOR PN 110P2-506-10-09-37.
• FORK END OF ACTUATORS PN 110P2-506-10-09-36 AND PN 110P2-506-10-09-38.
FIGURE 1: RUDDER TRIM TAB ACTUATOR INSPECTION
(SHEET 02 OF 02)
REVISION No.:  DATE: 21/Aug/2014  ALERT  SB No.: 110-27-A095  PAGE: 15
Copyright © 2014 by EMBRAER - All rights reserved.

### Page 16 (OCR)

-EMBRAER  SERVICE BULLETIN EVALUATION
THE PURPOSE OF THIS FORM IS TO COLLECT DATA THAT WILL BE USED TO IMPROVE THE QUALITY OF OUR
SERVICE BULLETINS AND UPDATE THE TECHNICAL PUBLICATION. PLEASE FILL IN FORM AND RETURN IT TO:
EMBRAER - EMPRESA BRASILEIRA DE AERONAUTICA S.A.
TECHNICAL PUBLICATIONS
AV. BRIG. FARIA LIMA, 2170
SAO JOSE DOS CAMPOS - SP - 12227-901
BRASIL
Fax: ++ 55 12 3927-7546
e-mail: service.bulletin@embraer.com.br
SB Title:  SB: (Number / Rev.)
Operator:  Aircraft serial number affected: (per SB effectivity list)
PRE-ACCOMPLISHMENT EVALUATION: (check applicable squares below)
[ ] WILL BE ACCOMPLISHED ON FIRST A/C  I ] WILL BE ACCOMPLISHED AS REQUIRED
[ ] WILL BE ACCOMPLISHED ON FLEET  I 1 DECISION DEFERRED (Explain below)
[ ]  UNECONOMICAL
SERVICE EXPERIENCE DOES NOT JUSTIFY
I ] WILL NOT BE ACCOMPLISHED:
OPERATIONAL ENVIRONMENT DOES NOT JUSTIFY
[ ]  OTHER (Explain below)
POST-ACCOMPLISHMENT EVALUATION: (Check applicable squares below)
ESTIMATED MANPOWER:  [ ]  [ ]  NOT OK (Explain below)
MATERIAL & KITS:  []  OK  [ ]  NOT OK (Explain below)
ACCOMPLISHMENT INSTRUCTIONS:  [ ]  OK  [ ]  NOT OK (Explain below)
FIGURES:  [ ]  OK  [ ]  NOT OK (Explain below)
SB GENERAL EVALUATION:  [ ]  OK  [ ]  NOT OK (Explain below)
COMMENTS: (Bulletin quality/ Difficulties found at the time of incorporation/ Suggested improvements/ Other)
Organization:  Fax:  Phone:
E-mail:
Address:  Prepared by: (Name/ Title)  Date:
ENS-003393

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
