# Engine Alliance Alert Service Bulletin EAGP7-A72-389: Revision 4

- Rights: © Engine Alliance. Filed by the FAA in regulations.gov docket FAA-2019-0465; AD 2019-16-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Engine Alliance Alert Service Bulletin EAGP7-A72-389](https://openairdocs.org/service-documents/engine-alliance/eagp7-a72-389.md)
- Title as filed: EA SB EAGP7-A72-389 rev 4
- Pages: 127
- PDF: https://openairdocs.org/files/sha256/11/43/11439bbd79f2726fafe10a92e3472d1a19c0bb2a2f814a6475b22b882fef693d
- Page: https://openairdocs.org/service-documents/engine-alliance/eagp7-a72-389/file/11439bbd79f2

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

██
██
ALERT
SER
VICE
BULLETIN
REVISION
NOTICE
ENGINE
—
HUB
ASSEMBL
Y
,
1ST
ST
AGE
LPC
ROT
OR
—
VISUAL
AND
EDDY
CURRENT
INSPECTION
OF
THE
F
AN
HUB
T
urbojet
Engine
Service
Bulletin
No.
EAGP7-A72-389
Revision
No.
4
dated
June
14,
2019.
Revision
History
Original
Issue
December
19,
2017
Revision
1
dated
January
19,
2018
Revision
2
dated
April
17,
2018
Revision
3
dated
October
18,
2018
Revision
4
dated
June
14,
2019
Reason
for
the
Revision
T
o
correct
Serial
Number
WBEUAK3810
to
WBDUAK3810
in
T
able
4.
T
o
replace
Serial
Number
WBDUAN5612
with
WBDUAN5676
in
T
able
4.
Ef
fect
of
Revision
on
Prior
Compliance
None.
Fan
Hubs
previously
inspected
to
NDIP-1
172
—
GP7000
Fan
Hub
Blade
Slot
Bottom
Manual
Eddy
Current
Inspection
(LPC
Module
Assy
,
Piece-part
or
Engine
(On-Wing
or
Of
f-Wing)
with
Fan
Blades
Removed,
Date
of
Issue:
December
15,
2017
(Original
Issue)
or
January
12,
2018
(Revision
A)
or
April
8,
2018
(Revision
B)
or
September
4,
2018
(Revision
C)
and
to
NDIP-1
173
—
GP7000
Fan
Hub
Blade
Slot
Front
Edge
Manual
Eddy
Current
Inspection
(LPC
Module
Assy
,
Piece-part
or
Engine
(On-Wing
or
Of
f-Wing)
with
Fan
Blades
Removed),
Date
of
Issue:
January
17,
2018
(Original
Issue)
or
April
9,
2018
(Revision
A)
have
incorporated
the
requirements
of
this
Service
Bulletin.
This
is
a
Complete
Revision
(Not
Applicable
to
the
SGML
version)
The
contents
are
in
accordance
with
the
list
of
ef
fective
pages.
All
pages
have
the
current
revision
number
.
T
echnical
changes
are
marked
with
black
bars.
MODEL
APPLICA
TION
GP7270,
GP7277
BULLETIN
ISSUE
SEQUENCE
EAGP7
Series
A72-389
Page
Revision
No.
Date
1
thru
25
4
June
14/19
A
copy
of
this
Revision
Notice
and
any
future
revision
notices
must
be
filed
as
a
permanent
record
with
your
copy
of
the
subject
bulletin.
EAGP7-A72-389
Page
1
of
1

### Page 2

(No text on this page.)

### Page 3

██
██
ALERT
SER
VICE
BULLETIN
ENGINE
—
HUB
ASSEMBL
Y
,
1ST
ST
AGE
LPC
ROT
OR
—
VISUAL
AND
EDDY
CURRENT
INSPECTION
OF
THE
F
AN
HUB
MODEL
APPLICA
TION
GP7270,
GP7277
BULLETIN
ISSUE
SEQUENCE
EAGP7
Series
A72-389
A
T
A
NUMBER
72-31-00
ENGINE
ALLIANCE,
LLC.
PROPRIET
AR
Y
INFORMA
TION
The
information
contained
in
this
document
is
Engine
Alliance,
LLC
(“EA”)
Proprietary
Information
and
is
disclosed
in
confidence.
It
is
the
property
of
EA
and
shall
not
be
used,
disclosed
to
others
or
reproduced
for
any
purpose,
including,
without
limitation,
to
design,
manufacture
or
repair
parts
or
to
obtain
F
AA
or
other
government
approval
to
do
so,
without
the
express
written
consent
of
EA.
Neither
receipt
nor
possession
of
this
document
alone,
from
any
source,
constitutes
such
permission.
Unauthorized
possession,
use,
copying
or
disclosure
may
result
in
criminal
and/or
civil
liability
.
If
consent
is
given
for
reproduction
in
whole
or
in
part,
this
notice
and
the
notice
set
forth
on
each
page
of
this
document
shall
appear
in
any
such
reproduction
in
whole
or
in
part.
This
technical
data
is
considered
subject
to
the
Export
Administration
Regulations
(EAR)
pursuant
to
15
CFR
Parts
730-774
respectively
.
T
ransfer
of
this
data
by
any
means
to
a
Non-US
Person,
whether
in
the
United
States
or
abroad,
without
the
proper
U.S.
Government
authorization
(i.e.
export
license,
license
exception,
NLR),
is
strictly
prohibited.
Export
Classification:
EAR
ECCN
9E991
Compliance
Category
2
EA
Distribution
Code
2686
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
1
of
25

### Page 4

Summary
The
purpose
of
this
Alert
Service
Bulletin
is
to
perform
a
one
time
Eddy
Current
Inspection
(ECI)
of
the
1st
Stage
Low
Pressure
Compressor
(LPC)
Rotor
Assembly
,
referred
to
as
the
fan
hub,
blade
slot
bottom
and
blade
slot
front
edge
for
cracks
and
to
perform
a
visual
inspection
of
the
fan
hub
for
damage.
Analysis
of
a
recent
uncontained
engine
fan
rotor
event
indicates
fan
hub
blade
slot
bottom/edge
ECI
and
visual
inspection
for
damage
is
prudent
interim
action
to
mitigate
potential
safety
risk.
Fan
hub
crack
indications
and
damage
must
be
evaluated
and
managed
to
the
limits
and
instruction
provided
herein.
Fan
hubs
found
with
damage
beyond
limits
or
rejectable
ECI
crack
indications
must
be
removed
from
service.
NOTE
:
This
inspection
can
be
done
on
fan
hubs
installed
in
engines
(on-wing
or
of
f-wing),
on
fan
hubs
at
LPC
Module
Assembly
level
or
fan
hubs
at
piece-part
level.
Planning
Information
Ef
fectivity
Data
Engine
Models
Applicable
GP7270,
GP7277
Engine
Serial
Nos.
—
Any
engine
that
has
Fan
Hub
Assembly
,
PN
5760221
or
PN
5760321,
with
a
serial
number
listed
in
T
able
1,
T
able
2,
T
able
3,
or
T
able
4.
NOTE
:
Fan
Hub
Assembly
PN
5760221
contains
detail
Hub
PN
5760201.
Fan
Hub
Assembly
PN
5760321
contains
detail
Hub
PN
5760301.
T
able
1
GROUP
1
NBDUAH3029
NBDUAH3074
WBDUAH5239
WBDUAH5243
WBDUAH5257
T
able
2
GROUP
2
NBDUAH3001
NBDUAH3004
NBDUAH3010
NBDUAH3055
NBDUAH3056
NBDUAH3082
NBDUAH3085
NBDUAH3098
WBDUAH5247
WBDUAH5248
WBDUAJ9292
WBDUAJ9294
WBDUAJ9299
WBDUAJ9301
WBDUAJ9317
WBDUAJ9318
WBDUAJ9323
WBDUAJ9326
WBDUAK3787
WBDUAK3799
WBDUAK3807
WBDUAK3824
WBDUAK3861
WBDUAK3868
WBDUAL5053
WBDUAL5073
WBDUAL5078
WBDUAM5831
WBDUAM5834
WBDUAP1372
NBDUAH3009
NBDUAH3014
NBDUAH3019
NBDUAH3021
NBDUAH3039
NBDUAH3041
NBDUAH3043
NBDUAH3046
NBDUAH3062
NBDUAH3078
WBDUAH5230
WBDUAH5235
WBDUAH5236
WBDUAH5241
WBDUAH5242
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
2
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 5

T
able
3
GROUP
3
NBDUAH3017
NBDUAH3022
NBDUAH3023
NBDUAH3024
NBDUAH3025
NBDUAH3032
NBDUAH3040
NBDUAH3045
NBDUAH3052
NBDUAH3054
NBDUAH3059
NBDUAH3063
NBDUAH3064
NBDUAH3066
NBDUAH3067
NBDUAH3068
NBDUAH3071
NBDUAH3073
NBDUAH3075
NBDUAH3076
NBDUAH3077
NBDUAH3079
NBDUAH3081
NBDUAH3084
NBDUAH3087
NBDUAH3088
NBDUAH3089
NBDUAH3090
NBDUAH3091
NBDUAH3093
WBDUAH5228
WBDUAH5229
WBDUAH5232
WBDUAH5234
WBDUAH5237
WBDUAH5244
WBDUAH5249
WBDUAH5250
WBDUAH5251
WBDUAH5253
WBDUAJ9306
WBDUAJ9307
WBDUAJ9309
WBDUAJ931
1
WBDUAJ9312
WBDUAJ9313
WBDUAJ9321
WBDUAJ9324
WBDUAJ9325
WBDUAJ9328
WBDUAJ9330
WBDUAJ9338
WBDUAJ9339
WBDUAK3794
WBDUAK3801
WBDUAK3805
WBDUAK3817
WBDUAK3822
WBDUAK3831
WBDUAK3836
WBDUAK3840
WBDUAK3846
T
able
4
GROUP
4
NBDUAH3002
WBDUAK3851
WBDUAL5125
WBDUAN561
1
NBDUAH3003
WBDUAK3852
WBDUAL5126
[Intentionally
Blank]
NBDUAH3005
WBDUAK3853
WBDUAM5757
WBDUAN5613
NBDUAH3006
WBDUAK3854
WBDUAM5758
WBDUAN5614
NBDUAH3007
WBDUAK3855
WBDUAM5759
WBDUAN5615
NBDUAH3012
WBDUAK3856
WBDUAM5760
WBDUAN5616
NBDUAH3013
WBDUAK3857
WBDUAM5761
WBDUAN5617
NBDUAH3015
WBDUAK3858
WBDUAM5762
WBDUAN5618
NBDUAH3016
WBDUAK3859
WBDUAM5763
WBDUAN5619
NBDUAH3018
WBDUAK3860
WBDUAM5764
WBDUAN5620
NBDUAH3020
WBDUAK3862
WBDUAM5765
WBDUAN5621
NBDUAH3026
WBDUAK3863
WBDUAM5767
WBDUAN5622
NBDUAH3027
WBDUAK3864
WBDUAM5769
WBDUAN5623
NBDUAH3028
WBDUAK3865
WBDUAM5770
WBDUAN5624
NBDUAH3031
WBDUAK3866
WBDUAM5771
WBDUAN5625
NBDUAH3033
WBDUAK3867
WBDUAM5772
WBDUAN5626
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
3
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 6

GROUP
4
NBDUAH3036
WBDUAK3869
WBDUAM5773
WBDUAN5627
NBDUAH3042
WBDUAK3870
WBDUAM5774
WBDUAN5628
NBDUAH3048
WBDUAK3871
WBDUAM5775
WBDUAN5629
NBDUAH3049
WBDUAK3872
WBDUAM5776
WBDUAN5630
NBDUAH3051
WBDUAK3873
WBDUAM5777
WBDUAN5631
NBDUAH3053
WBDUAK3874
WBDUAM5778
WBDUAN5632
NBDUAH3057
WBDUAK3876
WBDUAM5779
WBDUAN5633
NBDUAH3060
WBDUAK3877
WBDUAM5780
WBDUAN5634
NBDUAH3065
WBDUAK3878
WBDUAM5781
WBDUAN5635
NBDUAH3069
WBDUAK3879
WBDUAM5782
WBDUAN5636
NBDUAH3080
WBDUAK3880
WBDUAM5784
WBDUAN5639
NBDUAH3083
WBDUAL5028
WBDUAM5785
WBDUAN5640
NBDUAH3086
WBDUAL5029
WBDUAM5786
WBDUAN5641
NBDUAH3094
WBDUAL5031
WBDUAM5787
WBDUAN5642
NBDUAH3095
WBDUAL5032
WBDUAM5788
WBDUAN5643
NBDUAH3096
WBDUAL5033
WBDUAM5789
WBDUAN5645
NBDUAH3097
WBDUAL5034
WBDUAM5790
WBDUAN5646
WBDUAH5223
WBDUAL5035
WBDUAM5791
WBDUAN5647
WBDUAH5224
WBDUAL5036
WBDUAM5792
WBDUAN5648
WBDUAH5245
WBDUAL5037
WBDUAM5793
WBDUAN5649
WBDUAH5252
WBDUAL5038
WBDUAM5794
WBDUAN5650
WBDUAH5254
WBDUAL5039
WBDUAM5795
WBDUAN5651
WBDUAH5255
WBDUAL5040
WBDUAM5797
WBDUAN5652
WBDUAJ9293
WBDUAL5041
WBDUAM5798
WBDUAN5653
WBDUAJ9295
WBDUAL5042
WBDUAM5799
WBDUAN5654
WBDUAJ9296
WBDUAL5043
WBDUAM5800
WBDUAN5655
WBDUAJ9297
WBDUAL5044
WBDUAM5801
WBDUAN5656
WBDUAJ9298
WBDUAL5045
WBDUAM5802
WBDUAN5657
WBDUAJ9300
WBDUAL5046
WBDUAM5803
WBDUAN5659
WBDUAJ9302
WBDUAL5047
WBDUAM5804
WBDUAN5660
WBDUAJ9303
WBDUAL5048
WBDUAM5805
WBDUAN5661
WBDUAJ9304
WBDUAL5049
WBDUAM5806
WBDUAN5662
WBDUAJ9305
WBDUAL5050
WBDUAM5807
WBDUAN5663
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
4
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 7

GROUP
4
WBDUAJ9308
WBDUAL5051
WBDUAM5808
WBDUAN5664
WBDUAJ9310
WBDUAL5052
WBDUAM5809
WBDUAN5665
WBDUAJ9315
WBDUAL5054
WBDUAM5810
WBDUAN5666
WBDUAJ9316
WBDUAL5055
WBDUAM581
1
WBDUAN5667
WBDUAJ9319
WBDUAL5056
WBDUAM5812
WBDUAN5668
WBDUAJ9320
WBDUAL5057
WBDUAM5813
WBDUAN5669
WBDUAJ9322
WBDUAL5058
WBDUAM5814
WBDUAN5670
WBDUAJ9327
WBDUAL5060
WBDUAM5815
WBDUAN5671
WBDUAJ9329
WBDUAL5061
WBDUAM5816
WBDUAN5672
WBDUAJ9331
WBDUAL5062
WBDUAM5817
WBDUAN5673
WBDUAJ9332
WBDUAL5063
WBDUAM5818
WBDUAN5674
WBDUAJ9333
WBDUAL5064
WBDUAM5819
WBDUAN5675
WBDUAJ9334
WBDUAL5065
WBDUAM5820
WBDUAN5677
WBDUAJ9335
WBDUAL5066
WBDUAM5821
WBDUAN5678
WBDUAJ9336
WBDUAL5067
WBDUAM5822
WBDUAP1327
WBDUAJ9337
WBDUAL5068
WBDUAM5823
WBDUAP1328
WBDUAJ9340
WBDUAL5069
WBDUAM5824
WBDUAP1329
WBDUAK3781
WBDUAL5070
WBDUAM5825
WBDUAP1330
WBDUAK3782
WBDUAL5071
WBDUAM5826
WBDUAP1331
WBDUAK3783
WBDUAL5072
WBDUAM5828
WBDUAP1332
WBDUAK3784
WBDUAL5074
WBDUAM5829
WBDUAP1333
WBDUAK3786
WBDUAL5075
WBDUAM5830
WBDUAP1334
WBDUAK3788
WBDUAL5076
WBDUAM5832
WBDUAP1335
WBDUAK3789
WBDUAL5077
WBDUAM5833
WBDUAP1336
WBDUAK3790
WBDUAL5079
WBDUAM5835
WBDUAP1337
WBDUAK3791
WBDUAL5080
WBDUAM5836
WBDUAP1338
WBDUAK3792
WBDUAL5081
WBDUAM5837
WBDUAP1339
WBDUAK3793
WBDUAL5082
WBDUAM5838
WBDUAP1340
WBDUAK3795
WBDUAL5083
WBDUAM5839
WBDUAP1341
WBDUAK3796
WBDUAL5084
WBDUAM5840
WBDUAP1342
WBDUAK3797
WBDUAL5085
WBDUAM5841
WBDUAP1343
WBDUAK3798
WBDUAL5086
WBDUAM5842
WBDUAP1344
WBDUAK3800
WBDUAL5087
WBDUAM5843
WBDUAP1346
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
5
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 8

GROUP
4
WBDUAK3802
WBDUAL5088
WBDUAM5844
WBDUAP1347
WBDUAK3803
WBDUAL5089
WBDUAM5845
WBDUAP1348
WBDUAK3804
WBDUAL5090
WBDUAM5846
WBDUAP1349
WBDUAK3806
WBDUAL5091
WBDUAM5847
WBDUAP1350
WBDUAK3808
WBDUAL5092
WBDUAM5848
WBDUAP1351
WBDUAK3809
WBDUAL5093
WBDUAM5849
WBDUAP1352
WBDUAK381
1
WBDUAL5094
WBDUAM5850
WBDUAP1353
WBDUAK3812
WBDUAL5095
WBDUAM5851
WBDUAP1354
WBDUAK3813
WBDUAL5096
WBDUAM5852
WBDUAP1355
WBDUAK3814
WBDUAL5097
WBDUAM5853
WBDUAP1356
WBDUAK3815
WBDUAL5098
WBDUAM5855
WBDUAP1357
WBDUAK3816
WBDUAL5099
WBDUAM5856
WBDUAP1358
WBDUAK3818
WBDUAL5100
WBDUAN5579
WBDUAP1359
WBDUAK3819
WBDUAL5101
WBDUAN5580
WBDUAP1360
WBDUAK3820
WBDUAL5102
WBDUAN5581
WBDUAP1361
WBDUAK3821
WBDUAL5103
WBDUAN5582
WBDUAP1362
WBDUAK3823
WBDUAL5104
WBDUAN5583
WBDUAP1363
WBDUAK3825
WBDUAL5105
WBDUAN5584
WBDUAP1364
WBDUAK3826
WBDUAL5106
WBDUAN5585
WBDUAP1367
WBDUAK3827
WBDUAL5107
WBDUAN5586
WBDUAP1368
WBDUAK3828
WBDUAL5108
WBDUAN5587
WBDUAP1369
WBDUAK3829
WBDUAL5109
WBDUAN5588
WBDUAP1370
WBDUAK3830
WBDUAL51
10
WBDUAN5589
WBDUAP1371
WBDUAK3832
WBDUAL51
1
1
WBDUAN5590
WBDUAP1373
WBDUAK3833
WBDUAL51
12
WBDUAN5591
WBDUAP1374
WBDUAK3834
WBDUAL51
13
WBDUAN5592
WBDUAP1375
WBDUAK3835
WBDUAL51
14
WBDUAN5593
WBDUAP1376
WBDUAK3837
WBDUAL51
15
WBDUAN5594
WBDUAP4728
WBDUAK3838
WBDUAL51
16
WBDUAN5595
WBDUAP4729
WBDUAK3839
WBDUAL51
17
WBDUAN5596
WBDUAP4730
WBDUAK3841
WBDUAL51
18
WBDUAN5597
WBDUAP4732
WBDUAK3842
WBDUAL51
19
WBDUAN5598
WBDUAP4733
WBDUAK3845
WBDUAL5120
WBDUAN5603
WBDUAP4734
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
6
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 9

GROUP
4
WBDUAK3847
WBDUAL5121
WBDUAN5607
WBDUAP4736
WBDUAK3848
WBDUAL5122
WBDUAN5608
WBDUAP4737
WBDUAK3849
WBDUAL5123
WBDUAN5609
WBDUAK3810
WBDUAK3850
WBDUAL5124
WBDUAN5610
WBDUAN5676
Concurrent
Requirements
There
are
no
concurrent
requirements.
Reason
1.
Problem:
A.
A
GP7000
engine
experienced
an
in-flight
uncontained
fan
rotor
event.
Analysis
indicates
interim
action
is
prudent
to
mitigate
potential
safety
risk.
2.
Cause:
A.
The
cause
of
the
uncontained
fan
rotor
event
is
under
investigation.
3.
Solution:
A.
Perform
a
one
time
ECI
of
fan
hub
blade
slot
bottom
and
blade
slot
front
edge
for
cracks
and
perform
a
visual
inspection
of
the
fan
hub
for
damage.
Description
Do
an
ECI
of
the
fan
hub
blade
slot
bottom
and
blade
slot
front
edge
for
cracks
and
do
a
visual
inspection
of
the
fan
hub
for
damage.
Fan
hub
ECI
crack
indications
and
damage
must
be
evaluated
and
managed
to
the
limits
and
instruction
provided
herein.
Compliance
Category
2
Group
1
fan
hubs:
EA
recommends
you
perform
this
Service
Bulletin
as
soon
possible
but
by
February
14,
2018.
Group
2
fan
hubs:
EA
recommends
you
perform
this
Service
Bulletin
as
soon
possible
but
by
March
14,
2018.
Group
3
fan
hubs:
EA
recommends
you
perform
this
Service
Bulletin
as
soon
possible
but
by
October
15,
2018.
Group
4
fan
hubs:
EA
recommends
you
perform
this
Service
Bulletin
by
August
15,
2019
for
fan
hubs
that
will
have
3,000
Cycles
Since
New
(CSN)
or
more
on
August
15,
2019.
For
fan
hubs
that
will
not
have
3,000
CSN
or
more
on
August
15,
2019,
EA
recommends
you
perform
this
Service
Bulletin
before
the
hub
reaches
3,000
CSN.
See
T
able
5.
T
able
5
Fan
Hub
Cycles
Since
New
(CSN)
on
August
15,
2019
Comply
Before
CSN
greater
than
or
equal
to
3,000
August
15,
2019
CSN
less
than
3,000
Fan
Hub
CSN
=
3,000
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
7
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 10

Approval
Data
The
times
between
inspections
specified
in
Compliance
and
the
inspection
procedures
specified
in
the
Accomplishment
Instructions
agree
with
the
applicable
Federal
A
viation
Regulations
and
are
F
AA-Approved
for
the
engine
model(s)
given.
The
inspection
procedures
described
in
this
SB
are
reviewed
and
technically
accepted
by
Airbus
to
apply
to
the
Airbus
fleet
af
fected.
This
SB
does
not
contain
any
change
information
that
revises
the
equipment
definition
covered
by
Airbus
approved
modifications.
Manpower
The
estimate
of
man-hours
of
labor
directly
necessary
to
do
the
intent
of
this
Service
Bulletin
are
as
follows:
For
Fan
Hub
In
Engine
Installed
On
Aircraft
1.
Necessary
to
gain
and
close
access
........................................................
3.0
hours
2.
Necessary
to
perform
the
visual
inspection
...............................................
1.0
hour
3.
Necessary
to
perform
Eddy
Current
Inspection
.....................................
10.0
hours
4.
T
otal
Necessary
Man-hours
...............................................................
....
14.0
hours
For
Fan
Hub
In
Engine
Not
Installed
On
Aircraft
1.
Necessary
to
perform
the
visual
inspection
...............................................
1.0
hour
2.
Necessary
to
perform
Eddy
Current
Inspection
.....................................
10.0
hours
3.
T
otal
Necessary
Man-hours
...............................................................
.....
1
1.0
hours
For
Fan
Hub
Not
Installed
In
Engine
1.
Necessary
to
perform
the
visual
inspection
...............................................
1.0
hour
2.
Necessary
to
perform
ECI
...............................................................
.......
10.0
hours
3.
T
otal
Necessary
Man-hours
...............................................................
.....
1
1.0
hours
Clean
and
FPI
Inspect,
If
Required
1.
Clean
and
FPI
inspect,
if
required
............................................................
2.0
hours
2.
T
otal
Necessary
Man-hours
...............................................................
......
2.0
hours
Blend
Repair
,
If
Required
(per
blend
location)
1.
Blend
Repair
,
If
Required
...............................................................
..........
2.0
hours
2.
T
otal
Necessary
Man-hours
...............................................................
......
2.0
hours
Anti-gallant
T
ouch-Up
Repair
,
If
Required
(per
repair
location)
1.
Anti-gallant
T
ouch-up
Repair
,
If
Required
................................................
6.0
hours
2.
T
otal
Necessary
Man-hours
...............................................................
......
6.0
hours
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
8
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 11

W
eight
Data
No
Change.
Electrical
Load
Data
Not
Applicable.
Software
Accomplishment
Summary
Not
Applicable.
References
1.
Engine
Alliance
Standard
Practices
Manual,
Part
No.
5700139.
2.
Engine
Alliance
GP7270,
and
GP7277,
Illustrated
Parts
Catalog,
Part
No.
5700308.
3.
NDIP-1
172,
Revision
C
—
GP7000
Fan
Hub
Blade
Slot
Bottom
Manual
Eddy
Current
Inspection
(LPC
Module
Assy
,
Piece-part
or
Engine
(On-Wing
or
Of
f-Wing)
with
Fan
Blades
Removed,
Date
of
Issue:
September
4,
2018.
4.
Airbus
Aircraft
Maintenance
Manual
(AMM).
5.
GP7000
Series,
Engine
Manual
(EM),
Part
No.
5700147.
6.
GP7000
Series,
CIR
Manual,
Part
No.
5700309.
7.
NDIP-1
173
—
Revision
A
—
GP7000
Fan
Hub
Blade
Slot
Front
Edge
Manual
Eddy
Current
Inspection
(LPC
Module
Assy
,
Piece-part
or
Engine
(On-Wing
or
Of
f-Wing)
with
Fan
Blades
Removed),
Date
of
Issue:
April
9,
2018.
8.
NDIP
1
174
—
Revision
A
—
GP7000
Fan
Hub
Replication
to
Support
Local
Surface
Characterization
of
the
Blade
Slot
Bottom
(LPC
Module
Assy
,
Piece-part
or
Engine
(On-Wing
or
Of
f-Wing
with
Fan
Blades
Removed)),
Date
of
Issue:
April
10,
2018.
9.
Repair-1,
Blend
Repair
—
1st
Stage
LPC
Rotor
Hub
Assembly
Blade
Lock
Retaining
Lug
Aft
Edge.
10.
Repair-2,
1st
Stage
LPC
Rotor
Hub
Assembly
—
Blade
Slot
Bottom
—
Antigallant
Compound
T
ouch-Up
Repair
.
Publications
Changed
Engine
Alliance
GP7270
and
GP7277,
Illustrated
Parts
Catalog,
Part
No.
5700308.
72-31-00,
Figure
1
Interchangeability
Not
Applicable.
Information
in
the
Appendix
Alternate
Accomplishment
Instructions
(No)
Progression
Charts
(No)
Added
Data
(Y
es)
Revision
to
T
able
of
Limits
(No)
Inspection
Procedures
(No)
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
9
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 12

Material
Information
Material
—
Cost
and
A
vailability
1.
Part
prices
were
not
available
at
the
time
of
Service
Bulletin
publication.
Contact
Engine
Alliance
Spares
Management
&
Logistics
for
firm
quotations.
2.
There
is
no
kit
provided
to
do
this
Service
Bulletin.
3.
Part
availability
information
is
provided
in
material
data
Instructions
—
Disposition.
Industry
Support
Program
Not
Applicable.
The
material
data
that
follows
is
for
each
engine.
NOTE
:
It
is
possible
to
use
the
Chapter/Section
and
Figure/Item
reference
number
shown
below
the
old
part
number
to
find
the
part
in
the
Illustrated
Parts
Catalog.
Because
there
are
many
dif
ferent
configurations
used,
it
is
frequently
necessary
to
show
more
than
one
group
of
parts.
When
this
occurs,
parts
that
are
interchangeable
are
shown
line-by-line
only
,
unless
this
is
shown
dif
ferently
.
CAUTION
:
THE
FOLLOWING
MA
TERIAL
DA
T
A
T
ABLE(S)
ARE
ORGANIZED
BY
ILLUSTRA
TED
P
AR
TS
CA
T
ALOG.
ALL
P
AR
TS
IN
THE
T
ABLE(S)
MA
Y
OR
MA
Y
NOT
BE
APPLICABLE
T
O
ALL
THE
ENGINE
MODELS
SHOWN
IN
THE
T
ABLE
HEADING.
YOU
MUST
REFER
T
O
THE
APPROPRIA
TE
ILLUSTRA
TED
P
AR
TS
CA
T
ALOG
FOR
ENGINE
MODEL
APPLICABILITY
USING
THE
OLD
P
AR
T
NUMBER
(PN)
AND
CA
T
ALOG
SEQUENCE
NUMBER.
F
AILURE
T
O
INST
ALL
THE
P
AR
T(S)
IN
THE
CORRECT
ENGINE
MODEL
MA
Y
RESUL
T
IN
A
CONFIGURA
TION
THA
T
IS
NOT
F
AA
APPROVED.
The
material
data
that
follows
is
for
each
engine.
For
GP7270,
GP7277
Engines:
New
PN
Qty
Estimate
of
Unit
Price
($)
Keyword
Old
PN
Instructions
—
Disposition
1
*
HUB
ASSY
—
LPC
ROT
OR,
1STG
5760221
(72-31-00-1-10)
(4)(X)
OR
1
*
HUB
ASSY
—
LPC
ROT
OR,
1STG
5760321
(72-31-00-1-10
A)
(4)(X)
Modification
and
Spares
Information
Estimated
part
prices
are
provided
when
they
are
available
at
time
of
publication.
The
Estimate
of
Unit
Price
is
only
for
planning
purposes
and
does
not
constitute
a
firm
quotation.
An
asterisk
(*)
is
shown
where
part
pricing
information
was
unavailable.
In
either
case,
contact
Engine
Alliance,
LLC.
Spares
Management
&
Logistics
for
firm
quotations.
Parts
Modification
Conditions
(4)
Do
an
inspection
as
specified
in
the
Accomplishment
Instructions.
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
10
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 13

Spare
Parts
A
vailability
(X)
See
Reference
2,
Illustrated
Parts
Catalog
for
applicable
replacement
parts.
V
endor
Services
or
Special
Components/Materials
Not
Applicable.
Material
Data
for
Each
Spare
Engine
The
material
for
each
spare
engine
is
as
stated
in
the
preceding
material
information
section.
Reidentified
Parts
Not
Applicable.
Necessary
T
ools
No
more
Support
Equipment
is
necessary
.
Other
Material
Information
Data
Not
Applicable.
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
1
1
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 14

Accomplishment
Instructions
For
Fan
Hubs
At
LPC
Module
Assembly
Level
1.
Do
a
visual
inspection
of
the
fan
hub
as
follows:
A.
Do
a
visual
examination
of
the
fan
hub
rim
face
(Area
3A,
3B
and
3C),
rim
face
below
blade
slots
(Area
6),
clinch
nut
holes
(Areas
4
and
7),
scallops
(Area
5A,
5B
and
5C;
both
sides
of
the
flange),
fan
blade
lock
retention
hook
(Areas
1
&
2),
and
bore
area
behind
balance
flange
(Area
8)
for
damage
(nicks,
dents
and
scratches)
as
follows.
See
Figures
1,
2,
3
and
4.
(1)
Use
fluorescent
(white)
light
and
a
3X
–
10X
magnifying
glass
when
inspecting
Area
4,
Areas
5A,
5B
and
5C,
Area
6
and
Area
7.
(2)
Use
PW
A
107096
Checking
Gage
to
temporarily
identify
Areas
5A,
5B,
and
5C.
NOTE
:
PW
A
107096
Checking
Gage
is
recommended
for
Areas
5A,
5B
and
5C
scallop
location,
but
is
not
necessary
,
to
do
this
inspection.
(3)
If
necessary
,
clean
damage
areas
as
specified
in
Reference
1,
SPM
EAP-2202A
—
Aqueous
Cleaner
Wipe
Cleaning.
(a)
If
necessary
,
EAC-0048-2
Abrasive
Pad
may
be
used
to
aid
in
cleaning.
Swirl
marks
from
abrasive
pad
are
permitted.
(4)
Remove
any
high
metal
as
specified
in
Reference
1,
SPM,
EAP-4302
—
Blending.
Make
sure
that
you
do
the
Removal
of
High
Metal
procedure
only
.
(5)
The
following
methods
(or
equivalent),
may
be
used
to
determine
damage
depth:
NOTE
:
Use
of
a
borescope
is
not
recommended
for
damage
measurement
due
to
the
size
of
the
damage
being
inspected
and
the
sensitivity
of
the
results
to
technique.
The
inspector
is
responsible
for
the
accuracy
of
damage
measurements.
(a)
Reference
1,
SPM,
EAP-3023A
—
Surface
Pitting
And
Damage
Measurement
(Optical
Micrometer
Method).
(b)
Reference
1,
SPM,
EAP-3023C
—
Surface
Pitting
And
Damage
Measurement
(Replicating
Compound
Method).
1
Microset
101
R
T
thixotropic
compound
is
an
alternative
where
EAC-0055
is
specified.
It
will
harden
within
5
–
10
minutes
depending
on
ambient
temperature.
All
compound
residue
must
be
removed
from
the
part
surface
by
EAP-2201
—
Solvent
Wipe
Cleaning
after
the
replica
is
removed
from
the
part
surface.
Microset
101
R
T
compound
is
more
viscous
than
EAC-0055
and
will
work
well
on
vertical
inspection
surfaces.
(6)
If
damage
is
found,
see
T
able
6
and
Figures
1,
2,
3,
and
4
for
disposition.
(a)
Damage
in
an
area
coated
with
anti-gallant
that
does
not
meet
the
limits
of
T
able
6
may
be
evaluated
again
as
follows:
1
Remove
anti-gallant
from
and
adjacent
to
the
damaged
area
using
EAC-0048-2
Abrasive
Pad
and
EAC-0052
Acetone.
2
Re-measure
the
damage
depth
and
evaluate
to
T
able
6
limits.
(b)
If
damage
is
found
beyond
limits,
remove
the
fan
hub
for
repair
.
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
12
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 15

B.
Do
another
visual
inspection
of
the
fan
hub
as
specified
in
Step
1.A.
Y
ou
must
use
a
dif
ferent
inspector
from
the
one
used
previously
in
Step
1.A.
C.
If
no
damage
is
found
or
damage
is
serviceable
or
repairable,
proceed
to
ECI
task.
2.
Do
an
ECI
of
the
fan
hub
as
follows:
A.
Do
an
ECI
of
the
fan
hub
blade
slot
bottom
as
specified
in
Reference
3,
NDIP-1
172.
See
Added
Data.
B.
Do
an
ECI
of
the
fan
hub
blade
slot
front
edge
as
specified
in
Reference
7,
NDIP-1
173.
See
Added
Data.
C.
Fan
Hubs
with
rejectable
ECI
crack
indications
must
be
removed
from
the
assembly
and
sent
to
repair
vendor
for
further
evaluation.
3.
If
necessary
,
do
a
blend
repair
of
damage
found
during
visual
inspection.
See
Added
Data,
Reference
9,
Repair-1,
Blend
Repair
—
1st
Stage
LPC
Rotor
Hub
Assembly
Blade
Lock
Retaining
Lug
Aft
Edge.
4.
If
an
abrasive
impregnated
nylon
pad
was
used
to
remove
surface
contamination
products
from
the
blade
slot
bottom
as
specified
in
Reference
3,
NDIP-1
172
or
Reference
7,
NDIP-1
173
during
ECI
indication
evaluation,
perform
anti-gallant
touch-up
repair
on
the
af
fected
slot
bottom
area(s)
as
specified
in
Reference
10,
Repair-2,
1st
Stage
LPC
Rotor
Hub
Assembly
—
Blade
Slot
Bottom
—
Antigallant
Compound
T
ouch-Up
Repair
.
For
Fan
Hubs
At
Piece
Part
Level
1.
Do
a
visual
inspection
of
the
fan
hub
as
follows:
A.
Do
a
visual
examination
of
the
fan
hub
rim
face
(Areas
3A,
3B
and
3C),
rim
face
below
blade
slots
(Area
6),
clinch
nut
holes
(Areas
4
and
7),
scallops
(Areas
5A,
5B
and
5C,
both
sides
of
the
flange),
fan
blade
lock
retention
hook
(Areas
1
and
2)
and
bore
area
behind
balance
flange
(Area
8)
for
damage
(nicks,
dents
and
scratches)
as
follows.
See
Figures
1,
2,
3,
and
4.
(1)
Use
fluorescent
(white)
light
and
a
3X
–
10X
magnifying
glass
when
inspecting
Area
4,
Areas
5A,
5B,
and
5C,
Area
6
and
Area
7.
(2)
Use
PW
A
107096
Checking
Gage
to
temporarily
identify
Areas
5A,
5B,
and
5C.
NOTE
:
PW
A
107096
Checking
Gage
is
recommended
for
Areas
5A,
5B
and
5C
scallop
location,
but
is
not
necessary
,
to
do
this
inspection.
(3)
See
T
able
6
for
serviceable
damage
limits.
(4)
If
fan
hub
is
serviceable,
perform
ECI
task.
2.
Do
an
ECI
of
the
fan
hub
as
follows:
A.
Do
an
ECI
of
the
fan
hub
blade
slot
bottom
as
specified
in
Reference
3,
NDIP-1
172.
See
Added
Data.
B.
Do
an
ECI
of
the
fan
hub
blade
slot
front
edge
as
specified
in
Reference
7,
NDIP-1
173.
See
Added
Data.
C.
Fan
hubs
with
rejectable
ECI
crack
indications
must
undergo
further
evaluation
by
an
Engine
Alliance
NDE
specialist.
For
Fan
Hubs
Installed
In
An
Engine
(On-wing
Or
Of
f-wing)
1.
Inspect
the
fan
hub
as
follows:
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
13
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 16

A.
Remove
the
inlet
cone,
front
and
rear
segments
as
specified
in
Reference
4,
AMM
T
ask
72-31-41-000-803-A:
Removal
of
the
Inlet
Cone
or
Reference
5,
EM
T
ask
72-00-31-020-001:
Remove
The
Inlet
Cone.
CAUTION
:
YOU
MUST
USE
THE
STEPS
AND
THE
T
OOLS
(PW
A
107918,
PW
A
107919,
PW
A
107426
AND
PW
A
107525)
SPECIFIED
IN
THE
PROCEDURE
BELOW
T
O
REMOVE
THE
F
AN
BLADE
LOCK.
USE
OF
AL
TERNA
TE
T
OOLING
T
O
REMOVE
THE
F
AN
BLADE
LOCK
IS
NOT
PERMITTED.
IF
YOU
DO
NOT
OBEY
THIS
INSTRUCTION,
YOU
CAN
DAMAGE
THE
HUB
WHICH
CAN
CAUSE
THE
HUB
T
O
BE
DISCARDED.
B.
Remove
the
Fan
Blades
as
specified
in
Reference
4,
AMM
T
ASK
72-31-42-000-802-A:
Removal
of
the
LP
Compressor
1st
Stage
(Fan)
Blades
or
Reference
5,
EM
T
ask
72-00-31-020-002:
Remove
The
1st
Stage
Compressor
Rotor
Fan
Blades.
NOTE
:
Do
not
remove
PW
A
107525
Protective
Cover
from
the
fan
hub
after
fan
blade
removal.
C.
Do
a
visual
examination
of
the
fan
hub
rim
face
(Areas
3A,
3B
and
3C),
rim
face
below
blade
slots
(Area
6),
clinch
nut
holes
(Areas
4
and
7),
scallops
(Areas
5A,
5B
and
5C;
both
sides
of
flange),
fan
blade
lock
retention
hook
(Areas
1
and
2)
and
bore
area
behind
balance
flange
(Area
8)
for
damage
(nicks,
dents
and
scratches,)
as
follows.
See
Figures
1,
2,
3
and
4.
(1)
Use
fluorescent
(white)
light
and
a
3X
–
10X
magnifying
glass
when
inspecting
Area
4,
Areas
5A,
5B
and
5C,
Area
6
and
Area
7
(2)
Use
PW
A
107096
Checking
Gage
to
temporarily
identify
Areas
5A,
5B,
and
5C.
NOTE
:
PW
A
107096
Checking
Gage
is
recommended
for
Areas
5A,
5B
and
5C
scallop
location,
but
is
not
necessary
,
to
do
this
inspection.
(3)
If
necessary
,
clean
damage
areas
as
specified
in
Reference
1,
SPM,
EAP-2202A
—
Aqueous
Cleaner
Wipe
Cleaning.
(4)
If
necessary
,
EAC-0048-2
Abrasive
Pad
may
be
used
to
aid
in
cleaning.
Swirl
marks
from
abrasive
pad
are
permitted.
(5)
Remove
any
high
metal
as
specified
in
Reference
4,
AMM
T
ask
70-54-00-910-801-A
Blending
or
by
Reference
1,
SPM
EAP-4302
—
Blending.
Ensure
that
you
do
the
Removal
of
High
Metal
procedure
only
.
(6)
The
following
methods
(or
equivalent),
may
be
used
to
determine
damage
depth:
NOTE
:
Use
of
a
borescope
is
not
recommended
for
damage
measurement
due
to
the
size
of
the
damage
being
inspected
and
the
sensitivity
of
the
results
to
technique.
The
inspector
is
responsible
for
the
accuracy
of
damage
measurements.
(a)
Reference
1,
SPM,
EAP-3023A
—
Surface
Pitting
And
Damage
Measurement
(Optical
Micrometer
Method).
(b)
Reference
1,
SPM,
EAP-3023C
—
Surface
Pitting
And
Damage
Measurement
(Replicating
Compound
Method).
1
Microset
101
R
T
thixotropic
compound
is
an
alternative
where
EAC-0055
is
specified.
It
will
harden
within
5
–
10
minutes
depending
on
ambient
temperature.
All
compound
residue
must
be
removed
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
14
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 17

from
the
part
surface
as
specified
in
Reference
1,
SPM,
EAP-2201
—
Solvent
Wipe
Cleaning
after
the
replica
is
removed
from
the
part
surface.
Microset
101
R
T
compound
is
more
viscous
than
EAC-0055
and
will
work
well
on
vertical
inspection
surfaces.
(7)
If
damage
is
found,
see
T
able
6
and
Figures
1,
2,
3,
and
4
for
disposition.
(a)
Damage
in
an
area
coated
with
anti-gallant
that
does
not
meet
the
limits
of
T
able
6
may
be
evaluated
again
as
follows:
1
Remove
anti-gallant
from
and
adjacent
to
the
damaged
area
using
EAC-0048-2
Abrasive
Pad
and
EAC-0052
Acetone.
2
Re-measure
the
damage
depth
and
evaluate
to
T
able
6
limits.
(b)
If
damage
is
found
beyond
limits,
remove
the
engine
from
service.
(c)
If
no
damage
is
found
or
damage
is
serviceable
or
repairable,
proceed
to
ECI
task.
NOTE
:
Do
not
remove
the
protective
rug
from
the
inlet.
D.
Do
an
ECI
of
the
fan
hub
as
follows:
(1)
Do
an
ECI
of
the
fan
hub
blade
slot
bottom
as
specified
in
Reference
3,
NDIP-1
172.
See
Added
Data.
(2)
Do
an
ECI
of
the
fan
hub
blade
slot
front
edge
as
specified
in
Reference
7,
NDIP-1
173.
See
Added
Data.
(3)
Fan
hubs
with
rejectable
ECI
crack
indications
must
be
removed
from
the
assembly
and
sent
to
repair
vendor
for
further
evaluation.
E.
If
necessary
,
do
a
blend
repair
of
damage
found
during
visual
inspection.
See
Added
Data
Reference
9,
Repair-1,
Blend
Repair
—
1st
Stage
LPC
Rotor
Hub
Assembly
Blade
Lock
Retaining
Lug
Aft
Edge.
F
.
If
an
abrasive
impregnated
nylon
pad
was
used
to
remove
surface
contamination
products
from
the
blade
slot
bottom
as
specified
in
Reference
3,
NDIP-1
172
or
Reference
7,
NDIP-1
173
during
ECI
indication
evaluation,
perform
anti-gallant
touch-up
repair
on
the
af
fected
slot
bottom
area(s)
as
specified
in
Reference
10,
Repair-2,
1st
Stage
LPC
Rotor
Hub
Assembly
—
Blade
Slot
Bottom
—
Antigallant
Compound
T
ouch-Up
Repair
.
CAUTION
:
YOU
MUST
USE
THE
STEPS
AND
THE
T
OOLS
(PW
A
107918,
PW
A
107919,
PW
A
107426
AND
PW
A
107525)
SPECIFIED
IN
THE
PROCEDURE
BELOW
T
O
INST
ALL
THE
F
AN
BLADE
LOCK.
USE
OF
AL
TERNA
TE
T
OOLING
T
O
INST
ALL
THE
F
AN
BLADE
LOCK
IS
NOT
PERMITTED.
IF
YOU
DO
NOT
OBEY
THIS
INSTRUCTION,
YOU
CAN
DAMAGE
THE
HUB
WHICH
CAN
CAUSE
THE
HUB
T
O
BE
DISCARDED.
G.
Install
the
fan
blades
as
specified
in
Reference
4,
AMM,
T
ASK
72-31-42-400-802-A:
Installation
of
the
LP
Compressor
1st
Stage
(Fan)
Blades
or
Reference
5,
EM,
T
ask
72-00-31-420-004:
Install
The
1st
Stage
Compressor
Rotor
Fan
Blades.
(1)
It
is
required
to
apply
anti-gallant
paste
compound
EAC-0448
to
each
fan
blade
root
as
specified
in
the
above
installation
tasks.
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
15
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 18

(2)
Ensure
fan
blades
are
installed
in
the
correct
location
as
marked
during
disassembly
.
Incorrect
installation
may
result
in
high
engine
vibration.
H.
Do
a
visual
inspection
of
the
fan
hub
as
specified
in
Steps
1.C.
thru
1.C.(7)(b).
Y
ou
must
use
a
dif
ferent
inspector
from
the
one
used
previously
in
Steps
1.C.
thru
1.C.(7)(b).
NOTE
:
Areas
that
are
not
visually
accessible
due
to
fan
blade
lock
installation
do
not
require
inspection.
I.
If
necessary
,
do
a
blend
repair
of
damage
found
during
visual
inspection.
See
Added
Data
Reference
9,
Repair-1,
Blend
Repair
—
1st
Stage
LPC
Rotor
Hub
Assembly
Blade
Lock
Retaining
Lug
Aft
Edge.
J.
Install
the
inlet
cone,
front
and
rear
segments
as
specified
in
Reference
4,
AMM,
T
ask
72-31-41-400-803-A:
Installation
of
the
Inlet
Cone
or
Reference
5,
EM,
T
ask
72-00-31-420-005:
Install
The
Inlet
Cone.
T
able
6
Examine
Serviceable
Limits
Disposition
All
Locations
for:
Cracks
Any
quantity
Not
permitted.
Remove
fan
hub
from
service.
Any
damage
0.008
in.
(0.203
mm)
deep
or
less
Permitted
Any
damage
more
than
0.008
in.
(0.203
mm)
deep
up
to
0.020
in.
(0.508
mm).
Not
permitted.
Perform
blend
repair
,
if
allowed,
per
Repair-1.
If
blend
repair
is
not
allowed,
remove
fan
hub
from
service
for
repair
.
AREA
1
Fan
Blade
Lock
retention
hook
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.020
in.
(0.508
mm)
deep.
Not
permitted.
Remove
fan
hub
from
service
for
repair
.
AREA
1
Fan
Blade
Lock
retention
hook
for:
Anti-gallant
coating
chipped,
missing,
or
not
complete
All
quantities
Permitted.
Any
damage
0.005
in
(0.127
mm)
deep
or
less
Permitted.
AREA
2
Fan
Blade
Lock
retention
hook
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.005
in.
(0.127
mm)
deep
Not
permitted.
Remove
fan
hub
from
service
for
repair
.
AREA
2
Fan
Blade
Lock
retention
hook
for:
Anti-gallant
coating
chipped,
missing,
or
not
complete
Any
quantity
Permitted.
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
16
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 19

Examine
Serviceable
Limits
Disposition
Any
damage
0.004
in.
(0.102
mm)
deep
or
less
Permitted.
Area
3A
Rim
Face
behind
Fan
Blade
Lock
Retention
Hook
(anti-gallant
coated
area)
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.004
in
(0.102
mm)
deep
Not
permitted.
Remove
the
fan
hub
from
service
for
repair
.
Area
3A
Rim
Face
behind
Fan
Blade
Lock
Retention
Hook
(anti-gallant
coated
area)
for:
Anti-gallant
coating
chipped,
missing,
or
not
complete
All
quantities
Permitted
Any
damage
0.002
in.
(0.051
mm)
deep
or
less
Permitted.
Area
3B
Rim
Face
below
Fan
Blade
Lock
Retention
Hook
(anti-gallant
coated
area)
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.002
in
(0.051
mm)
deep
Not
permitted.
Remove
the
fan
hub
from
service
for
repair
.
Area
3B
Rim
Face
below
Fan
Blade
Lock
Retention
Hook
(anti-gallant
coated
area)
for:
Anti-gallant
coating
chipped,
missing,
or
not
complete
All
quantities
Permitted
Any
damage
0.002
in.
(0.051
mm)
deep
or
less
Permitted
Area
3C
Rim
Face
(not
coated
with
anti-gallant)
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.002
in
(0.051
mm)
deep
Not
permitted.
Remove
the
fan
hub
from
service
for
repair
.
Any
damage
0.001
in.
(0.025
mm)
deep
or
less
Permitted.
Area
4
(24
Locations)
Areas
to
a
maximum
of
0.125
in.
(3.175
mm)
around
the
clinch
nut
hole
countersink
diameter
±
45
degrees
from
T
op
Dead
Center
(front
side
of
the
flange)
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.001
in.
(0.025
mm)
deep
Not
permitted.
Remove
the
fan
hub
from
service
for
repair
.
Any
damage
0.001
in.
(0.025
mm)
deep
or
less.
Damage
must
be
measured
in
the
axial
and
radial
direction.
Permitted.
Area
5A
(24
Locations)
Scallop
face
and
edge
(front
and
rear
side
of
the
flange)
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.001
in.
(0.025
mm)
deep.
Damage
must
be
measured
in
the
axial
and
radial
direction.
Not
permitted.
Remove
the
fan
hub
from
service
for
repair
.
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
17
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 20

Examine
Serviceable
Limits
Disposition
Any
damage
0.006
in.
(0.152
mm)
deep
or
less.
Damage
must
be
measured
in
the
axial
and
radial
direction.
Permitted.
Area
5B
(24
Locations)
Scallop
face
and
edge
(front
and
rear
side
of
the
flange)
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.006
in.
(0.152
mm)
deep.
Damage
must
be
measured
in
the
axial
and
radial
direction.
Not
permitted.
Remove
the
fan
hub
from
service
for
repair
.
Any
damage
0.001
in.
(0.025
mm)
deep
or
less
Permitted.
Area
5C
(24
Locations)
Hub
face
to
a
maximum
of
0.150
in.
(3.810
mm)
around
the
scallop
(front
and
rear
side
of
the
flange)
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.001
in.
(0.025
mm)
deep
Not
permitted.
Remove
the
fan
hub
from
service
for
repair
.
Any
damage
0.001
in.
(0.025
mm)
deep
or
less.
Permitted.
Area
6
(24
Locations)
Area
below
the
blade
slot
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.001
in.
(0.025
mm)
deep
Not
permitted.
Remove
the
fan
hub
from
service
for
repair
.
Any
damage
0.002
in.
(0.051
mm)
deep
or
less
Permitted
Area
7
(24
Locations)
Areas
to
a
maximum
of
0.125
in.
(3.175
mm)
around
the
clinch
nut
hole
countersink
diameter
remaining
270
degrees
not
covered
by
Area
4
(front
side
of
the
flange)
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.002
in.
(0.051
mm)
deep
Not
permitted.
Remove
the
fan
hub
from
service
for
repair
.
Any
damage
0.002
in.
(0.051mm)
deep
or
less
Permitted
Area
8
Bore
area
behind
balance
flange
for:
Nicks,
dents
and
scratches
Any
damage
more
than
0.002
in.
(0.051
mm)
deep
Not
permitted.
Remove
the
fan
hub
from
service
for
repair
.
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
18
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 21 (OCR)

CER  Engine Alliance
(FAN BLADES, FAIRINGS, SPACERS AND
INLET CONE REMOVED)
B527042A
LOCATION OF THE FAN HUB
72-31-00
FIGURE 1
December 19/17  EAGP7-A72-389
| REVISION NO. 4 - June 14/19  Page 19
ENGINE ALLIANCE, LLC PROPRIETARY INFORMATION
Subject to the export control restrictions on the cover or first page.

### Page 22 (OCR)

ER Engine Alance
1 (ALL AROUND)
ЗВ
SEE AREA
3B AND
AREA 6
3C(*)  6 (SEE FIGURE 2,  EDGE OF
SHEET 2)  A  ANTI-GALLANT
SECTION A-A  COATING
NOTE: CLINCH NUT OMITTED FOR CLARITY
NOTE: (1) SEE ALSO AREA 4, AREAS 5A/5B/5C AND AREA 7
(2) THE DIVISION BETWEEN AREA 3A AND AREA
3B IS THE INNER DIAMETER OF THE HOOK
(REFERENCE ONLY)
FILLETS
IN
AREA 2
ЗА
ЗВ
(PARTIAL)  B (PARTIAL, ROTATED)
B527043B
FAN HUB INSPECTION LOCATIONS 1, 2, 3A, 3B, 3C, 6
FIGURE 2, SHEET 1
December 19/17  EAGP7-A72-389
• REVISION NO. 4 - June 14/19  Page 20
ENGINE ALLIANCE, LLC PROPRIETARY INFORMATION
Subject to the export control restrictions on the cover or first page.

### Page 23 (OCR)

ED Engine Allanco
0.100
(2.540)
2.214 (56.236)
(REFERENCE)
B527262
FAN HUB INSPECTION LOCATIONS 1, 2, 3A, 3B, 3C, 6
FIGURE 2, SHEET 2
December 19/17  EAGP7-A72-389
I REVISION NO. 4 - June 14/19  Page 21
ENGINE ALLIANCE, LLC PROPRIETARY INFORMATION
Subject to the export control restrictions on the cover or first page.

### Page 24 (OCR)

TDC
45 DEGREES  45 DEGREES
AREA 7
AREA 4
BOLT HOLE TOP DEAD
CENTER +/- 45 DEGREES
INLET CONE
AREA 4 AND 7  MATING SURFACE
0.125 (3.175)  (REFERENCE)
AROUND THE
CLINCH NUT HOLE
(24 LOCATIONS)
B527044A
FAN HUB INSPECTION LOCATIONS 4 AND 7
FIGURE 3
December 19/17  EAGP7-A72-389
I REVISION NO. 4 - June 14/19  Page 22
ENGINE ALLIANCE, LLC PROPRIETARY INFORMATION
Subject to the export control restrictions on the cover or first page.

### Page 25 (OCR)

ER  Engine Alliance
TYPICAL DAMAGE
(TYPICAL EDGE FEATURE)
FWD  AFT
RADIAL
DEPTH —
BOTH DIRECTIONS
" AXIAL
SECTION B - B
B527045B
FAN HUB INSPECTION LOCATION 5
FIGURE 4, SHEET 1
December 19/17  EAGP7-A72-389
I REVISION NO. 4 - June 14/19  Page 23
ENGINE ALLIANCE, LLC PROPRIETARY INFORMATION
Subject to the export control restrictions on the cover or first page.

### Page 26 (OCR)

HUB FACE AREA
AROUND SCALLOP
AREA 5A
AREA 5B
AREA 5B
0.452 (11.480) MAXIMUM
FROM INLET CONE
AREA 5C  MATING DIAMETER
PWA 107096  (EACH SIDE OF SCALLOP
CHECKING GAGE  AT 24 LOCATIONS)
(OPTIONAL)
B527261
FAN HUFIGURE 4, SALET TION 5
December 19/17  EAGP7-A72-389
Page 24
ENGINE ALLIANCE, LLC PROPRIETARY INFORMATION
Subject to the export control restrictions on the cover or first page.

### Page 27

Appendix
Added
Data
Internal
Reference
Information
Revision
No.
Reference
Document
Origination
Original
EA17AC178
CEL/JAC
1
EA17AC178A
CEL/JAC
2
EA18AC062
CEL/JAC
3
EA18AC190
CL/RCM
4
EA19AC085
CL/JEJ
Number
values
shown
in
parentheses
adjacent
to
U.S.
values
are
International
System
of
units
(SI)
equivalents.
Reference
3,
NDIP-1
172
Rev
.
C,
follows.
Reference
7,
NDIP-1
173
Rev
.
A,
follows.
Reference
8,
NDIP-1
174,
Rev
.
A,
follows.
Reference
9,
Repair-1,
Blend
Repair
—
1st
Stage
LPC
Rotor
Hub
Assembly
Blade
Lock
Retaining
Lug
Aft
Edge,
follows.
Reference
10,
Repair-2,
1st
Stage
LPC
Rotor
Hub
Assembly
—
Blade
Slot
Bottom
—
Antigallant
Compound
T
ouch-Up
Repair
,
follows.
l
December
19/17
EAGP7-A72-389
REVISION
NO.
4
-
June
14/19
Page
25
ENGINE
ALLIANCE,
LLC
PROPRIET
AR
Y
INFORMA
TION
Subject
to
the
export
control
restrictions
on
the
cover
or
first
page.

### Page 28 (OCR)

GP7000 Fan Hub
Blade Slot Bottom Manual Eddy Current Inspection
LPC Module Assy, Piece-part or
Engine (On-Wing or Off-Wing with Fan Blades Removed)
PRAIT & WHI
NDIP-1172 - Revision C
VARNING
THIS DOCUMENT MAY CONTAIN INFORMATION SUBJECT TO THE INTERNATIONAL TRAFFIC IN ARMS REGULATION (ITAR) OR THE
EXPORT ADMINISTRATION REGULATION (EAR)OF 1979. THIS INFORMATION MAYNOT BE EXPORTED, RELEASED, OR
DISCLOSED TO FOREIGN NATIONALS OUTSIDE THE UNITED STATESVITHOUT FIRST COMPLYNG VATH THE EXPORT LICENSE
REQUIREMENTS OF THE INTERNATIONAL TRAFFIC IN ARMS REGULATION (ITAR) AND/OR THE EXPORT ADMINISTRATIONT
REGULATION (EAR). AVIOLATION OF THEITAR OR EAR MAY BE SUBJECT TO APENALTY OF UP TO 10 YEARS IMPRISONMENTT
AND A FINE OF $1,000,000 UNDER 22 U.S.C 2778 OR SECTION 2410 OF THE EXPORT ADMINISTRATION ACT OF 1979.INCLUDE
THIS NOTICE WITH ANY REPRODUCED PORTION OF THIS DOCUMENT.
RESTRICTION
PAGES OF THIS DOCUMENT MARKED WITH THE NOTICES SET FORTH BELOW CONTAIN CONTRACTOR COMPETITION SENSITIVE
DATA ANDOR PRATT & VHITNEYPROPRIETARYDATAWHICH IS SUBMITTED IN CONFIDENCE-NO DISCLOSURE OR USE OF THIS
INFORMATION IS PERMISSIBLE WTHOUT PRIOR WRITTEN CONSENT OF UNITED TECHNOLOGIES CORPORATION EXCEPT FOR
OFFICIAL PURPOSES MTHIN THE L.S. GOVERNMENT.
DOCUMENT PROPERTY RIGHTS NOTICE
THISDOCUMENT IS THE PROPERTY OF UNITED TECHNOLOGIES CORPORATION (UTC). YOU MAY NOT POSSESS, USE, COPYOR
ISCLOSE THIS DOCUMENT OR ANY INFORMATION IN IT, FOR ANYPURPOSE, INCLUDING MATHOUT LIMITATION TO DESIGNT
MANUFACTURE OR REPAIR PARTS, OR OBTAIN FAA OR OTHER GOVERNMENT APPROVAL TO DO SO WITHOUT UTC'S EXPRESS
WRITTEN PERMISSION. NEITHER RECEIPT NOR POSSESSION OF THIS DOCUMENT ALONE, FROM ANYSOURCE, CONSTITUTES
SUCH PERMISSION. POSSESSION, USE, COPYRIGHT OR DISCLOSURE BY ANYONE VITHOUT UTC'S EXPRESS VIRITTEN
PERMISSION IS NOT AUTHORIZED AND MAY RESULT IN CRIMINAL AND OR CIML LIABILITY.
NOTICES
Pratt & Whitney Proprietary Information
US Export Controlled: ECCN EAR99

### Page 29 (OCR)

NDIP-1172 - Revision C
GP7000 Fan Hub
Blade Slot Bottom Manual Eddy Current Inspection
LPC Module Assy, Piece-part or
Engine (On-Wing or Off-Wing with Fan Blades Removed)
CANT & WHITE
Instructions described within this procedure do not replace, amend or supersede any instructions
included in other Pratt & Whitney technical publications. Active Service Bulletins and other technical
publications published by Pratt & Whitney comprise approved technical data.
Written by: Lisa Brasche
Approved by: Lisa Brasche
Original Issue Date: December 15, 2017
Revision History:
Revision  Letter  Revision Date  Changes  Revision By  Approved By
Release  Initial  Dec 15, 2017  NIA  L. Brasche  L. Brasche, PL3
Jan 12, 2018  Technical updates  L. Brasche  L. Brasche, PL3
Apr 8, 2018  Technical updates  L. Brasche  L. Brasche, PL3
Sept 4, 2018  Technical updates  L. Brasche  L Brasche, PL3
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 30 (OCR)

NDIP-1172 - Revision C
GP7000 Fan Hub
Blade Slot Bottom Manual Eddy Current Inspection
LPC Module Assy, Piece-part or
Engine (On-Wing or Off-Wing with Fan Blades Removed)
GENERAL:
The purpose of this eddy current inspection is to detect cracking in the tan blade slot bottom of the
GP7000 1st Stage Low Pressure Compressor (LPC) Rotor Assembly (fan hub), PN 5760221 or PN
5760321. (Note Fan Hub Assembly PN 5760221 contains detail Hub PN 5760201 and Fan Hub
Assembly PN 5760321 contains detail Hub PN 5760301). This procedure is for the inspection of a part
in either a module or onwing/offwing engine configuration or piece-part (thoroughly disassembled) with
the fan blades removed. This inspection is a manual eddy current inspection developed to support
field or shop inspection for the GP7000 fan hub. The highest stress regions are near the forward edge
of the slot bottom. The latter 1.5 inches will not be inspected with the engine installed. The same
procedure/hardware can be used to inspect the slot regardless of the fan hub assembly level.
The inspection consists of the following sequences:
• Nine probes to cover the required region
• Pre-inspection calibration
• Inspection
• Accept Reject analysis
• Post-inspection calibration
• Report completion
Pratt & Whitney technical data describing part inspections using a commercially available eddy current
inspection is written with a level of detail that assumes instrument and probes are properly maintained
and the NDT inspectors are qualified and are familiar with operating the equipment.
REFERENCES:
UniWest EVi Instrument User Manual
Olympus iPlex UltraLite Industrial Videoscope (JV8620U) User Manual
Pratt & Whitney Proprietary Inb: mation - US Export Controlled: ECCN EAR99

### Page 31 (OCR)

NDIP-1172 - Revision C
III. INSPECTOR QUALIFICATIONS:
Only qualified operators, specifically designated, trained, and approved can perform this inspection.
A Pratt & Whitney task specific certificate will be issued to qualified inspectors. The following
requirements must be met:
• Have obtained forty (40) hours of hands on instruction and familiarization with test
equipment, probes, and inspection technique.
• Operators shall demonstrate inspection readiness on PW-approved test parts). The student
will evaluate instructor-selected areas in the inspection zone and the results will be
compared to lab results to determine success of student technique. The instructor's
assessment of candidate's capability of performing the inspection is based on successtul
completion and accurate quantification of known defects in the PW-approved test part(s).
The instructor may provide additional training or advise additional training as needed to a
candidate. This evaluation is conducted by Pratt & Whitney approved instructors only.
• Inspector recertification is required if more than six months elapses without having
performed an inspection or completed training/refresher training. Recertification may require
up to a three day refresher course given by a Pratt & Whitney approved instructor.
• Contact the Pratt and Whitney MPE/NDE for questions regarding inspector training.
IV. INSPECTION PREPARATION:
A. Required Equipment List
ITEM  NUMBER  DESCRIPTION  SUPPLIER
1  Uniwest #99977  EVi Eddy Current Instrument  Uniwest
2  Uniwest #96384  EVi Batteries (quantity - 8)  Uniwest
Uniwest #96574  Battery Charger  Uniwest
4  Uniwest #77159  AC Adapter  Uniwest
5  Uniwest #92374  Power Cords  Uniwest
6  Uniwest #100252  4-Button Remote  Uniwest
7  Uniwest #100145  Multiplexer  Uniwest
8  Uniwest 74714  Cable Assembly - Evi to MUX  Uniwest
9  NA  Flat head screwdriver  Wiha or equivalent
10  Wiha 3/32  3/32" Allen Wrench  Wiha or equivalent
11  PWA106161  ECP 1098 - Zone 4 probe  Pratt & Whitney
4
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 32 (OCR)

NDIP-1172 - Revision C
ITEM  NUMBER  DESCRIPTION  SUPPLIER
12  PWA 106160  ECP 1097 - Zone 4/5 probe  Pratt & Whitney
13  PWA 106159  ECP 1096 - Zone 5 probe  Pratt & Whitney
14  PWA 106158  ECP 1095 - Zone 6 probe  Pratt & Whitney
15  PWA106157  ECP 1094 - Zone 7 probe  Pratt & Whitney
16  PWA 106156  ECP 1093 - Zone 8 probe  Pratt & Whitney
17  PWA106155  ECP 1092 - Zone 9 probe  Pratt & Whitney
18  PWA106154  ECP 1091 - Zone 9/10 probe  Pratt & Whitney
19  PWA 106153  ECP 1090 - Zone 10 probe  Pratt & Whitney
20  PWA 106172  US-3647 Calibration Standard  Pratt & Whitney
21  Uniwest #77217  Shipping Case  Uniwest
B.  Required Equipment Description:
1. Eddy Current Instrumentation
a. Uniwest EVi and 4-button remote
The Uniwest EVi instrument (Figure 1) is required for this inspection with array capability enabled.
The 4-button remote aids in "Null", "Clear", "FreezeScreen" and "Screenshot" functions. Associated
accessories to enable operation include batteries, adapter cables, and power cables.
5
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 33 (OCR)

NDIP-1172 - Revision C
Eddy Current
Instrument
GP7000 KIT5  DOC00D
4-button
Remote  I010 Ol
Figure 1. Eddy current instrument (Uniwest EVI) and 4-button remote.
b. Multiplexer
The Uniwest Multiplexer (PN 100145) and cable (PN 74714) are needed for array operation in
combination with the EVi instrument and associated probes.
Cable  Multiplexer
Uni Wes!
1500-40
SOCH KALTIPLEXER
UNIVERSAL DOWNESTIO
Figure 2. Multiplexer and cable used with eddy current instrument.
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 34 (OCR)

NDIP-1172 - Revision C
2. Eddy Current Probe Set - (PWA106153 thru PWA106161)
a. Probe ID:
Nine probes are utilized to cover the full 2.1" inspection zone as shown in Figure 3. Each probe
covers a 0.34" area with a 0.02" overlap between zones. Zone 4/5 (PWA 106160) and Zone 9/10
(PVA 106154) provide double coverage in the most critical areas. Note the forward edge taper
which provides ease of access into the slot and ensures proper probe entry.
Probe Set
Probe Motion
FWD to AFT  cc
Zone 10  Zone 9/10  Zone 9  Zone 8  Zone 7  Zone 6  Zone 5  Zone 4/5  Zone 4
PWA106153  PWA106154  PWA106155  PWA106156  PWA106157  PWA106158  PWA106159  PWA100160  PWA106161
Figure 3. Probe set, contains nine probes needed to provide coverage of the required
inspection zone.
b. Probe design:
Each probe contains an eight channel sensor comprised of two, paired elements per channel. The
probe for zone 7 is shown as an example in Figure 4 (left). The sensor is installed in a spring-
loaded "flapper" (Figure 4 - expanded view - middle). The sensor is comprised from eight paired-
elements (16 total elements) aligned for optimal crack detection for the orientation shown. When
one of the two pairs passes over the crack, the affected channel will respond. If multiple elements
are affected, the impedance plane response will indicate the interaction with a "figure-8" pattem
(Figure 4 - right).
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 35 (OCR)

NDIP-1172 - Revision C
Crack  Crack
orientation  orientation
Response on
multiple channels
when multiple
sensor elements
are passed over
crack
Probe motion
Figure 4. Probe (Zone 7) contains 8-channel sensor (left and expanded view) with paired-
elements travelling normal to the crack orientation. Paired-elements that pass over the
crack will result in a response on the respective impedance plane display for the affected
channels (right).
c. Probe - instrumentation interface
Details of the probe configuration and instrument response are shown in Figure 5. For the GP7000
inspection, the instrument is set to eight-channels where each channel is tied to an element pair
(Figure 5 a).
The sensor is comprised of two rows of four channels. The elements are staggered to ensure full
coverage (Figure 5 b).
During scanning, the display is set to show all eight channels (Figure 5c). Monitor the impedance
plane display for "figure 8" responses. Note that multiple channels may show a response
depending on crack position with respect to element position, as shown in Figure 5c where F1, F2
and F3 all show some response. In this example, the F2 element pair is best positioned with
respect to the notch as it shows the highest amplitude response.
The color options shown here were selected to work in aircraft shop environments where lighting
can be a factor. Other color selections for background and trace color can be selected as needed
to facilitate review using the "GENERAL SETTINGS" functions in the "ADVANCED" menu
selections.
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 36 (OCR)

NDIP-1172 - Revision C
The instrument display can also be set to individual channels to assist with analysis (Figure 5d).
(a)  Two Element Pair = One  Channel  R
Two rows of
(b)  Four Channels
Display eight
(c)  channels for
detection
Display single
(d)  channel for  →
analysis
Figure 5. Probe construction begins with pairs of differential elements tied to one of eight
channels (a). The eight pairs of elements are aligned in two rows (b) which can be displayed
simultaneously (c) or as individual channels (d).
3. Calibration Standard PWA106172 (US 3647)
Calibration is accomplished by traversing a notched standard over each of the elements for each of
the sensors. The notch standard contains a 0.020" x 0.010" semi-circular notch at the center of the
titanium segment. Figure 6 shows the calibration fixture (PWA106172) which includes a
micrometer that enables controlled motion of the notch standard over the sensor (Figure 6 right).
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 37 (OCR)

NDIP-1172 - Revision C
Micrometer
Notch
Standard
Notch
Standard
Probe  Probe  Sensor
stand
Figure 6. Calibration fixture, PWA106172, (left) shown with probe positioned for
optimization. Notch standard in position above sensor (right)
C.  Miscellaneous tools:
1. Fan Containment Case Work Stand, PWA 107274: Used to assist with inlet access, if available
2. Dry wipes and resealable plastic bags: Lint free wipes used to remove excess lubricant from
blade slots. Resealable plastic bags used to transport dry wipes to/from the inlet
3. Isopropyl alcohol wipes: Used as needed to remove excess antigallant remnants
4. Part marker. Only Trace Element Certified (TEC) Sharpie markers, Silver Pencils or other
approved markers.
Protective tape: Cover the eddy current probe sensor and flapper area with a smooth wrinkle
free layer of Kapton or PTFE tape.
6. Scissors, scalpel or equivalent: Utilized for preparation of tape used to protect the sensor.
7. 3/32" allen wrench: Used for connection of probes to multiplexer.
8. Screwdriver: Used to tighten screws as necessary for the EVI.
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 38 (OCR)

NDIP-1172 - Revision C
9. Olympus iPlex UltraLite Industrial Videoscope (IV8620U) or equivalent: Used for local viewing
of surface condition as needed for onwing inspection.
10. Headlamp, flashlights and lamps: Used as necessary to assist with task lighting.
D.  Inspection Zone
The inspection can be performed on fan hubs either installed in an engine or module (Figure 7 left)
or uninstalled, from forward to aft of the blade slot bottom. The inspection coverage requirement is
a 2.1" section of the fan hub slot bottom as indicated by the green arrow (Figure 7 right).
Figure 7. GP 7000 fan hub in installed position (left) with probe inserted. Inspection
coverage indicated by green arrow (right) on forward face.
The blade slot bottom is divided into nine zones as shown in Figure 8. Zones 4, 5, 6, 7, 8, 9 and 10
overlap by approximately 20 mils. Zone 4/5 and Zone 9/10 provide "double coverage" in the most
critical areas of the slot bottom.
11
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 39 (OCR)

NDIP-1172 - Revision C
FRWD
Zone 4/5  Zone 9/10
Zone 6  Zone 8
Zone 4  Zone 10
Zone 5  Zone 7  Zone 9
Figure 8. Zone map for the slot bottom probes.
Inspection Preparation
This inspection was developed to support crack detection during onwing inspection of the GP7000,
fan hub assembly PN 5760221 and PN 5760321. The fan blades will be removed to allow
inspection of the blade slots but the hub will remain installed in the engine. For inspection, the lock
ring, fan blades, fan blade fairings and blade spacers are removed to enable full access of the
probe.
1. If available, the Fan Containment Case Work Stand, PWA 107274, can be used to improve
access to the fan hub slots. PWA 107274 is a rectangular shaped platform made of
thermoplastic construction (Figure 9).
12
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 40 (OCR)

NDIP-1172 - Revision C
DETAIL STEP
(2 LOCATIONS)
FAN CASE
DETAIL
LEFT BASE
PWA 107274
DETAIL
RIGHT BASE
Figure 9. PWA 107274 work stand used to improve access to the inspection area.
2. For onwing inspection, the lubrication products will remain in the slots. Dry wipes will be used to
remove loose antigallant similarly to shown in Figure 10, prior to starting the inspection. A
plastic cleaning tool, Uniwest # 73220, is available for use with the dry wipes as shown in Figure
10. FOD prevention measures should be used to ensure that all wipes are removed from the
inlet. Resealable plastic bags can be used to transport wipes to/from the inlet. Wipes should be
counted prior to entry and after use to ensure no inadvertent loss of wipes during the cleaning
process. All slots should be wiped out prior to inspection start.
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 41 (OCR)

NDIP-1172 - Revision C
Figure 10. Cleaning aid (left) and dry wipes (right) used to remove loose lubrication
products from the slots prior to inspection.
3. To ensure that all blades are inspected and assist with data recording, the slots shall be
marked, Slot 1 through Slot 24, in CCW direction as shown in Figure 11. To identify Slot 1, first
look for a balance weight tab that may be marked with white or yellow paint (Figure 11 right).
There are dot-peened "0" markings on either side of the slot (Figure 11 left) to confirm Slot 1 or
identify if the paint is not present. Use TEC Sharpie to mark each slot, 1 through 24.
14
Pratt & Whitney Proprietary In formation - US Export Controlled: ECCN EAR99

### Page 42 (OCR)

NDIP-1172 - Revision C
Slot 1
Slot 2
Slot 1
Slot 24
Figure 11. Dot peen marking, "0", (left) used to identify slot 1. Balance tab below Slot 1 may
also be painted yellow or white (right). Fan hub contains 24 slots, to be numbered in CCW
direction. .
F.  Instrument Preparation and Initial Setup
1. The EVi instrument as shown in Figure 12 is used for this inspection. Install Cable #74714 and
connect to multiplexer #100145. Note that the instrument serial number (SN) is located on the
upper corner of the back of the instrument (Figure 12, lower image). The SN for the instrument
and the multiplexer will be recorded on the data sheet (Attachment A).
15
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 43 (OCR)

NDIP-1172 - Revision C
GP7000 KIT5
SERIAL NO
Figure 12. EVi instrument (upper image) and control buttons, including power button in
lower right corner. Serial number is on upper corner of the back of the instrument (lower
image).
2. Tape the probe using the 0.5" wide tape (Figure 13 left). The tape should cover the flapper and
sensor area from forward to aft. Ensure that the tape does not impede motion of the flapper.
The flapper should be able to fully engage without a high or low spot. The tape prevents wear
of the sensor and protects the flapper region from antigallant contamination. Figure 13 shows a
probe after use in a hub with antigallant in place. During inspection the probe should be
monitored for build-up of antigallant and/or damage to the tape. Dry wipes can be used to
remove antigallant from the probe body as needed. A lightly damp, isopropyl wipe can be used
to remove remaining adhesive from the sensor surfaces as needed.
16
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 44 (OCR)

NDIP-1172 - Revision C
Figure 13. UHMW tape used to prevent wear (left) applied over full probe body length to
provide optimal protection of flapper. Probe with tape in place over sensor and flapper area
(right), after use, showing build-up of antigallant.
3.  Connect the Zone 4 probe, PWA 106161 to the multiplexer. Use the slide, to position the
protective cover of the multiplexer and place the probe connector such that set screws engage
(Figure 14 left). Using the 3/32 allen wrench, tighten the set screws to engage the probe
connector (Figure 14 right). Turn on the EVi using the power button at the lower right edge of
the instrument (Figure 12, upper right).
Figure 14. Multiplexer to probe connection (left). 3/32" allen wrench used to connect the
probe to multiplexer (right).
17
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 45 (OCR)

NDIP-1172 - Revision C
4. The probe includes a probe body, shaped to fit into the contour of the GP7000 slot. The entry
edge (Figure 15, upper left) is tapered to more easily enter the slot geometry. The probe
description, PN and SNs are on the probe control surface (upper right). A spring compliant
flapper is used to position the sensor (Figure 15, lower middle) against the part surface. The
spring compliance of the flapper must remain engaged during calibration and throughout the
inspection. The probe SN is recorded on the data sheet (Appendix A) for each of the probes
during the inspection.
Entry
edge
Uni West.
PWA 106161
ECP-1098 GP7000
ZONE-4 CONCAVE
S/N 70130
Flapper
Sensor
Figure 15. Probe construction. Entry surface (upper left); probe descriptors (upper right).
Probe flapper and sensor (lower).
18
Pratt & Whitney Proprietary Infomation - US Export Controlled: ECCN EAR99

### Page 46 (OCR)

NDIP-1172 - Revision C
5. Load the SETTINGS file (Figure 16):  | F6/DIFF 77/DIFF F8/DOF
ADVANCED  C-SCAN  HELP
a. Enter the "BASIC" menu. Use the
EDDY CURRENT
vertical slider to highlight the  GENERAL SETTINGS
"FILE" functions and hit "ENTER"  PLOT LAYOUT/TYPE
Ensure that the "FILE TYPE" is set  ALARM SETUP  FILE
to SETTINGS". If not use the  RUN SCRIPT
POST PROCESS
vertical slider to change to
"SETTINGS". Use the vertical
slider to highlight "LOAD" and  FILE TYPE: SETTINGS
press "ENTER".  SAVE: a70222  LOAD: 1091
DELETE
b. Check the setting file names for  RENAME:
the probe serial number. If the
serial number of the probe being  FILE LOCATION: INTERNAL
loaded is avallable, select the file.
c. If the file name for the probe serial  COPY LOGS
number is not available, select
"GP7000_SLOT" from the drop
down list and press "ENTER". Wait
until the "Load Settings" is
complete before moving to the next
step.
Figure 16. Basic menu, FILE function
controls. Use vertical slider to set FILE TYPE
to SETTINGS.
19
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 47 (OCR)

NDIP-1172 - Revision C
6.  Set the File Naming convention (Figure  15/DIFF F6/DIFF F7/DIFF F8/DIFF
17 (a}):  BASIC  ADVANCED  C-SCAN  HELP
a. After loading the settings file,  EDDY CURRENT
highlight the "FILE TYPE" option  GENERAL SETTINGS  PLOT LAYOUT/TYPE
and change to "SCRN SHOT" as  ALARM SETUP
shown here. Ensure SCRN SHOT  RUN SCRIPT  FILE
FMT is set to JGP and FILE  POST PROCESS
LOCATION is set to INTERNAL as
shown.
FILE TYPE: SCRN SHOT
SCRN SHOT FMT: JPG
b.  Turn on the AUTO NAME  SAVE:
FEATURE.  LOAD:
DELETE:
C. Set the PRIMARY BASE NAME to  RENAME:
ZABBCCC where "A" is the zone  TRANSFER FILE
number, BB is set to inspector's  FILE LOCATION: INTERNAL
initials, and CCC is the last three  TILANSFER DESTINATION: NotAvailable
digits of the probe serial number.  REMOVE USE MEDIA: Not Avallable
COPY LOGS
Set the Secondary Base Name to  AUTO NAME ON: ON
FDDDEEEE where DDD is the last  PRIMARY BASE NAME: ZN7
three digits of the calibration  SECONDARY BASE NAME: 70137
standard used for this inspection  DELETE AUTO NAME FILES  AUTO NAME INDEX: O
and EEEE are the last four digits of
the fan hub serial number.
e. Auto name index should be set to 0
at the start of the inspection.
The file naming convention will
need to be changed for each probe
change.
After setting the file name, save the
settings file to include the naming
convention specific to the probe.
h. Prior to the start of the inspection,
enter the primary base name and
secondary base name to ensure
that the file naming convention is
activated. Failure to do so may
lead to use of the auto name
indexing feature only.
Figure 17 (a). Basic menu, FILE function
controls. Use vertical slider to set
AUTONAME functions specific to the probe
and fixture.
20
Pratt & Whitney Proprietary Information - US Export Controlled: ECON EAR99

### Page 48 (OCR)

NDIP-1172 - Revision C
7. Confirm Eddy Current Parameter  Settings (Figure 17 (b)):  F5/DIFF  F6/DIFF  F7/DIFF  F8/DIFF  1315
BASIC  ADVANCED C-SCAN  HELP
a. To access the settings, go to the
"BASIC" menu, use the vertical  slider to select "EDDY CURRENT"  GENERAL SETTINGS  EDDY CURRENT
PLOT LAYOUT/TYPE
and press ENTER. The  ALARM SETUP
FREQUENCY/CHANNEL should be  FILE
at F1/DIFF. Use the ENTER  RUN SCRIPT
function as necessary to set to  POST PROCESS
FX/DIFF where X = 1 thru 8.
b. Verify that F1/DIFF thru F8/DIFF on  FREQUENCY/CHANNEL: F1/DIFF
the EVi instrument is set to the  FREQ ENABLED: YES
following initial settings.  FREQUENCY: 6.00 MHZ
GAIN:
c. Frequency is enabled and set to 6  H GAIN: 71.0 dB
MHz for all channels.  V GAIN: 71.0 dB
ROTATION: 342.0 Deg
d. Gain (H Gain and V Gain) and  LOW PASS FILTER: 60 Hz
rotation will be adjusted per the  HIGH PASS FILTER: 2 Hz
calibration procedure below for  PROBE DRIVE: HIGH
each of the eight channels.  PROBE DRIVE ADJUST: 100 %
X NULL POS: 0.0 Div
e. Low pass filter: 60 Hz  Y NULL POS: 0.0 Div
DEFAULT CURRENT FREQ
f. High pass filter: 2 Hz  SET AS CURRENT: ALL
DEFAULT ALL FREQS
g. Probe Drive: High  DISPLAY SHIFT: 0 Deg
SCAN START: Not Available
h. Probe Adjust: 100%  PLOT: MAIN 1
SENSITTVITY V/DIV: 2V
i. X and Y Null Pos: 0 Div  AUTO CLEAR: OFF
PERSISTENCE: OFF
J. Display Shift: 0 Deg
k. Senstivity V/Div: 2V
Figure 17 (b). Basic menu, FILE function
1. Auto Clear and Persistence: OFF  controls. Use vertical slider to set AUTONAME
functions specific to the probe and fixture.
G.  Probe Calibration
The calibration fixture (Figure 18) is comprised of a probe stand and adjustment arms used to
manipulate the notch standard over the sensor to optimize the response of each of eight sensor
pairs. The adjustment am includes a micrometer used to control motion of the notch standard.
1. Prior to inserting the probe, ensure that the probe stand surface is clean and contains no
protrusions that would prevent the probe from setting flat.
21
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 49 (OCR)

NDIP-1172 - Revision C
2. Check the notch standard surface to ensure thatthe 0.005" tape is in place overthe notch
surface. Replace the tape if it shows wear or is torn. For inspection of parts in the cleaned
state, le, with antigallant materials removed, the tape shall be removed from the calibration
standard. This will prevent over-inspection of parts in the "cleaned" state.
Micrometer
Adjustment
knobs
Probe
stand
Figure 18. Calibration fixture (side view - left; forward view - right).
3. The notch standard arm can be folded back out of position while inserting the probe into the
probe stand (Figure 19 left). After connecting the probe to the multiplexer as described above in
D.2, place the probe in an inverted position as shown in Figure 18. The sensor is placed in the
forward position for optimal contact between the sensor and the notch standard.
4. Ensure that the tape over the flapper/sensor is intact if used since last application of clean tape.
5. Set the micrometer to approximately 0.100" as shown in Figure 19 (right).
22
Pratt & Whitney Proprietary Information - US Export Controlled: ECON EAR99

### Page 50 (OCR)

NDIP-1172 - Revision C
Figure 19. Calibration fixture with notch standard arm folded out of position for probe
placement (left). Micrometer, set to 0.100" for initial set-up (right).
6.  The calibration notch is located in the center of the notch standard. Ensure that the notch
standard contains a layer of tape prior to the calibration process. The purpose of the tape is to
simulate the liftoff that will occur when antigallant is present. For inspection of parts in the
cleaned state, i.e, with antigallant materials removed, the tape shall be removed from the
calibration standard. This will prevent over-inspection of parts in the "cleaned" state.
Position the stops (Figure 20 left) such that the notch standard edge does not pass over the
sensor during the calibration process. Failure to do so will lead to edge effects during the
measurement and unsuccessful calibration. Proper notch standard position with respect to the
sensor is shown in Figure 20 (right).
STOP
Notch Standard
Figure 20. Calibration fixture with stop in place to prevent edge effect during calibration
(left). Proper notch standard to sensor position (right).
8. Perform the null operation with the notch standard shifted off center such that the notch is not in
position above the active sensor elements.
9. Use the angle adjustment knob (Figure 21 upper left) to set the notch standard in a position
parallel to the sensor flapper. (Contact check shown in Figure 21 upper right).
23
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 51 (OCR)

NDIP-1172 - Revision C
10. Use the translation knob (Figure 21 upper left) to set the notch standard in a position that
channel F1 (Figure 21 lower left) has "figure 8" impedance plane response.
11. Check that the notch standard is in contact with the sensor and that the flapper is not tilted. If
the probe body is tilted, check for burrs or debris. Wipe with clean wipe if needed. If the flapper
is tilted, check the tape to make sure the flapper is able to move freely. Retape if needed.
12. Repeat step G.8 to re-null the instrument.
Translation  Contact
adjustment  check
Angle
adjustment
Element 8
Element 1  position
position
Figure 21. Translation and angle adjustment knobs used to set initial notch standard
position over the sensor (upper left) to arrive at proper contact between standard and sensor
(upper right). Notch standard in element 1 (lower left) and element 8 (lower right).
13. Use the display button (right side of EVi - see Figure 12) to set to all 8 channels. While
monitoring the display, shift the notch standard forward until F1 response is at a maximum
value. Lock the translation adjustment knob when a maximum value is arrived at as shown in
Figure 22.
14. Use the display button to switch to single channel option (Figure 23). Set the FREQUENCY
CHANNEL to F1/DIFF. Adjust the rotation as needed so that the response to the notch is
vertical.
15. Use the micrometer to translate the notch standard in 5 mil increments from the original 0.100"
setting (see Figure 19), monitoring for the notch response by sliding the notch over the sensor
at each position. Reduce the translation distance from 5 mil increments to 2 mil increments to
24
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 52 (OCR)

NDIP-1172 - Revision C
fine tune to the optimal notch response (optimal position response - OPR). The response will
increase when the notch passes over the L and R elements of a paired sensor (Figure 5).
Choose the pair half (Lor R) that provides the highest response, to set the gain.
16. After finding the OPR, adjust the gain such that the response is 6 Vptp +/- 0.2V (Figure 23).
Use the SET AS CURRENT: ALL feature as shown in Figure 23 to adjust all other channels to
the rotation and gain settings found for F1. This serves as a starting point for the other
channels.
Figure 22. Eight-channel display option with sensor optimally placed for F1 response.
Calibration voltage is 6V Vpp +/- 0.2V.
25
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 53 (OCR)

NDIP-1172 - Revision C
FF:6.00 MH: 01  WELF
LIV/DIY  lena IV/Div
am:60.5 dl  Gain:60.5 dN  GENTRAL SETTINGS
Hot: 297.9 Deg  Rot: 297.9 Deg  PLOT LAVOUL/TYPE
ALARM SETUP
FILE
RUN SCHIT
POST PROCESS
FREQUENCY/CHANNEL: FUTIFF
FREQ ENABLED: YES
FREQUENCY: 6.00 MH
GALN
11 GAIN: 60.5 JU
Y GAIN: 605 C
ROTATION: 297.9 Deg
LOW PASS FILTER: 60 1
TOCH PASS FILTER: 2 HO
PROBE DRIVE: HIGH
PROBE DRIVE ADUST: 100~
X NULL POS: 0.0 DA
Y NULL POS: 0.0 DI
DISPLAY SHIFT: O Deg
PLOT: SPUT 1
SENSITIVITY V/DIV: IV
AUTO CLEAR: OFF
PERSISTENCE: OFF
SAVE
Figure 23. Single channel display set to monitor and adjust the F1 response. Calibration
voltage is set to 6V Vpp +/-0.2V. Note circular gate used to aid in disposition decision.
17. Return the display to the eight-channel option. Use the micrometer to translate 20 mils,
monitoring the F2 response. As with arriving at the OPR for F1, use the micrometer to translate
the notch standard in 5 mil increments, monitoring for the notch response by sliding the notch
over the sensor at each position. Reduce the translation distance from 5 mil increments to 2 mil
increments to fine tune to the optimal notch response.
18. After finding the OPR, return to the single channel display option and set the FREQUENCY
CHANNEL to F2/DIFF. Adjust the rotation to vertical. Adjust the gain such that the response is
6 Vptp +/- 0.2V (Figure 23).
19. Repeat steps 17 and 18 until all eight channels have been set to 6 Vptp +/- 0.2V. To assist with
tracking the optimal position between elements, a probe calibration worksheet is provided as an
appendix to this document.
20. After completion of calibration of all eight channels, use the SCREENSHOT function to record
an 8-channel display. Note the file name on the data recording sheet to enable recall as
needed during the inspection.
V.  INSPECTION
A. UNINSTALLED, FAN HUB PIECE PART OR LPC MODULE LEVEL ASSEMBLY INSPECTION
Inspection of the LPC Module Assembly or single piece-part inspection can be performed in a shop
setting either with antigallant or in the fully cleaned state.
26
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 54 (OCR)

NDIP-1172 - Revision C
1. Record the calibration settings for the Zone 4 probe on the Data Recording Sheet provided in
Appendix A.
2. Confirm that all other details on the Data Recording Sheet are recorded.
3. Confirm SLOT 1 is accurately marked as defined in Section IV.E.3.
4. Insert the probe into Slot 1 as shown in Figure 24. Null the probe once the sensor is past the
edge entry.
White paint
indicating
Slot 1
Figure 24. Probe insertion into Slot 1 (left) showing sensor contact with part edge.
5. Move the probe from forward to aft, monitoring the eight-channel display while traversing the
probe thru the slot. The use of the remote will aid in clearing noise (Figure 25).
Figure 25. Remote used to clear screen.
27
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 55 (OCR)

NDIP-1172 - Revision C
6. Use the "Freeze Screen" and SCRN SHOT function buttons on the remote to record indications
of interest. Pushing the SCRN SHOT button will save the screenshot to the EVi internal drive
for later download and analysis using the file name established during the setup. Use the
comments column on the Data Recording Sheetto record file name information regarding saved
SCRN SHOT data.
7. Record data in the eight-channel display mode. Identify the channel(s) of interest for a given
indication. Record screen shots for each of the channels of interest.
8. Switch the display back to the eight element display when the inspection is resumed below.
9. Continue the inspection till all 24 slots have been inspected with the Zone 4 probe.
10. Return to the calibration fixture and confirm that the post calibration response for all elements is
within +/- 0.5Vptp for all elements of the probe following the steps in Section IV.G.
11. Move to the next probe, following the calibration steps in Section IV.G., until calibration,
inspection and post-inspection checks are complete for all nine probes.
12. Complete the Data Recording Report for all nine probes.
B. INSTALLED, ONWING/OFFWING INSPECTION
Inspection of the fan hub can be performed onwing/offwing in the installed condition with antigallant
in place.
1. Record the calibration settings for the Zone 4 probe on the Data Recording Sheet provided in
Appendix A.
2. Confirm that all other details on the Data Recording Sheet are recorded.
3. Confirm SLOT 1 is accurately marked as defined in Section IV.E.3.
4. After calibration of the probe (Section IV.G), the instrument is placed in the interior of the fan
hub on foam padding (Figure 26 upper right) to enable sufficient viewing of the display (lower
image) for inspection decision making and prevent inadvertent contact damage to the fan hub.
2₴
Pratt & Wintney Proprietary Information - US Export Controlled: ECCM EAR99

### Page 56 (OCR)

NDIP-1172 - Revision C
Figure 26. Engine inlet (upper left) prior to removal of blades. Position instrument in ID of
the fan hub (upper right) using foam pad to prevent inadvertent damage (lower image).
5. Insert the probe into Slot 1 as shown in Figure 27. Null the probe once the sensor is past the
edge entry. It is recommended to null the probe on entry of each slot.
6. Move the probe from forward to aft, monitoring the eight-channel display while traversing the
probe thru the slot. The use of the remote will aid in clearing noise.
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 57 (OCR)

NDIP-1172 - Revision C
White paint
indicating
Slot 1
Figure 27. Probe insertion into Slot 1 (left) showing sensor contact with part edge. Note
white paint on this part indication Slot 1 position.
7. Use the "Freeze Screen" and SCRN SHOT function buttons on the remote to record indications
of interest. Pushing the SCRN SHOT button will save the screenshot to the EVi internal drive
for later download and analysis using the file name established during the setup. Use the
comments column on the Data Recording Sheet to record file name information regarding saved
SCRN SHOT data
8.  Record data in the eight-channel display mode. Identify the channel(s) of interest for a given
indication. Record screen shots for each of the channels of interest
9. Switch the display back to the eight element display when the inspection is resumed below.
10. Continue the inspection till all 24 slots have been inspected with the Zone 4 probe.
11. Return to the calibration fixture and confirm that the post calibration response for all elements is
within +/- 0.5Vptp for all elements of the probe following the steps in Section IV.G.
30
Pratt & Whitney Proprietary Information - US Export Controlled: ECCN EAR99

### Page 58 (OCR)

NDIP-1172 - Revision C
12. Move to the next probe, following the calibration steps in Section IV.G, until calibration,
inspection and post-inspection checks are complete for all nine probes.
13. Complete the Data Recording Report for all nine probes.
VI.  Rejection Criteria
A. Reportable indications
1. Indications greater than 4 Vptp and having the figure eight response in the vertical position or
rotated into the upper right/lower left quadrant (Figure 28 left) are considered reportable
indications.
2.  Any indications that exceed the circular gate must be evaluated to determine disposition.
Figure 28 (left) shows a response that exceeds the gate. Note that the V Vpp is less than 4V.
To disposition, change the rotation such that the response is vertical as shown in Figure 28
(right). If the rotated signal exceeds, 4V Vpp but is less than 6V Vpp, it is a reportable indication
and must be documented on the data recording form. Use the iSCRN SHOT function to record
indications of interest. If the response is rotated as shown in Figure 28, the original response
and the response rotated to vertical shall be recorded. Note that they are recordable in the
comments column of the data recording sheet.
F4/DIFF: 6,00 MHR CA H Vpp  2,03  F4/ DIFF:6:00 M
Seas IV/DIv  3178  Sens 1V/Div
Gain: 62.2 aB  Gain: 62.2 dB
1: Dei  Rot: 287.1| De
Response exceeds gate  Rotate to vertical to disposition
Figure 28. Indication exceeds circular gate (left). Rotation changed to set response to
vertical (right) for disposition. Indications greater than 4V Vpp are reportable. Indications
that are greater than 6V Vpp are rejectable.
3. Ensure that the channel of interest is returned to the original rotation value after documentation
Is complete.
B. Rejectable indications
1. Indications greater than 6 Vptp and having the figure eight response in the vertical position
(Channel F3 in Figure 29) or rotated into the upper right/lower left quadrant (Channels F3, F4
31
Pratt & Whitney Proprietary In formation - US Export Controlled: ECCN EAR99

### Page 59 (OCR)

NDIP-1172 - Revision C
and F4 in Figure 30) are considered rejectable indications. Use the "SCRN SHOT function to
record rejectable indications. Note they are rejectable in the comments column of the data
recording sheet.
Figure 29. Indication exceeds 6V Vpp in F3 channel. Note crack is also detectable in
channels F2 and F4.
Figure 30. Indication exceeds 6V Vpp in F3, F4 and F5 channels. Rotation into upper
right/lower left quadrant occurs for deeper cracks.
2. For any indications greater than 10 divisions, reduce the gain by 6dB increments as needed to
capture an unsaturated signal. Record the dB reduction on the data sheet. Use the "Freeze"
32
Pratt & Whitney Proprietary In formation - US Export Controlled: ECCN EAR99

### Page 60 (OCR)

NDIP-1172 - Revision C
and "SCRN SHOT" function to record indications of interest in both original and reduced gain
settings.
3. Ensure that the channel of interest is returned to the original gain rotation settings after
documentation is complete.
PART DISPOSITION:
A. If the eddy current inspection indicates a recordable or rejectable reading, 4Vptp or larger,
perform the following steps.
1. Mark the approximate location of the indication using a silver pencil. As in Figure 31 (left), mark
the location of the indication, including the slot number. Mark a region approximately 4" in
length as shown in Figure 31.
2. Wearing gloves, clean the part by manually rubbing the inspection surface (Figure 31 middle)
with Isopropyl alcohol wipe followed by a dry wipe. Use the silver markings from step VII.A.1, to
guide the area to be wiped. The area can be wiped with up to three isopropyl wipes with hand
3. Repeat the eddy current inspection of the local area. (Figure 31 lower right)
4. Utilize a borescope if available to capture images of the local surface condition. Look for
evidence of wear features. pitting or other geometrical features in the area of the ECT response.
Look for presence of surface contamination from the antigallant, plasma coating from the fan
blades, sandidirt or other organic materials, and/or transfer material from the blade platform.
Record images for inclusion in final reporting.
5. I If the use of alcohol dampened wipes does not sufficiently remove surface contamination
products, Abrasive Impregnated Nylon Pads as specified by PMC-4095 and/or EAC-0048-2 can
The process is limited to hand-held use of pads only. Dremels, rotary tools and other
hand-held power tools shall not be used for surface preparation for this inspection.
6. Acceptable materials include 3M Scotch Brite (fine) - 7447. Other grits of Scotch Brite are not
acceptable. Additionally, Norton 747 and Weller Corp. Non-woven Hand Pad 5416 are
acceptable. Indicate in the upper right hand corner of the data recording sheet if abrasive pad
has been used. Y ( ) or N( ). For those slots in which the abrasive pad has been used.
indicate the numbers of locations within that slot were affected. As an example, if a single
location in a slot was affected, it would read slot x (1).
7. Wearing gloves, manually rub the inspection surface with the Abrasive Impregnated Nylon
Material. Remove residue by wiping with Isopropyl alcohol.
8. Repeat the eddy current inspection of the local area. (Figure 31 lower right)
9. If indications exceed the rejection criteria in Section V.H. after the cleaning steps, the part is
considered rejectable and must be removed from service for further evaluation.
10. Identily blade slot location(s) that were cleaned using an abrasive pad in the Data Recording
Report.
33
Pratt & Wintney Proprietary Information - US Export Controlled: ECCM EAR99

The text continues at https://openairdocs.org/service-documents/engine-alliance/eagp7-a72-389/file/11439bbd79f2.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
