# Epic Aircraft Service Bulletin 0034: Revision B

- Rights: © Epic Aircraft. Filed by the FAA in regulations.gov docket FAA-2023-1503; AD 2023-20-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Epic Aircraft Service Bulletin 0034](https://openairdocs.org/service-documents/epic/sb-0034.md)
- Title as filed: Epic Aircraft Service Bulletin SB-0034 Rev B
- Pages: 15
- PDF: https://openairdocs.org/files/sha256/d4/32/d432e81c1ce76a7d63bef27b7e2dacbcb99b6a2f0e6f5a52b7f61bde7f52f1ae
- Page: https://openairdocs.org/service-documents/epic/sb-0034/file/d432e81c1ce7

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 1 of 15 
 
 
Subject: Flap Secondary Limit Switch Installation  
 
ATA-Code: 27-50  
 
Labor: 6.0 Hours Effectivity:  K003 – K032 
 
Affected Model(s):  E1000, E1000 GX Due:  Next annual inspection. 
 
Compliance:  Mandatory Recurrence: No 
1 BACKGROUND AND PURPOSE: 
It has been found on affected aircraft that if the flap actuator down limit switch fails it may allow 
the flaps to overextend which may prevent them from being retracted from the full position. It is 
also possible for the take-off limit switch to become damaged if not correctly aligned during 
rigging. 
 
This Service Bulletin gives instructions to install a secondary full position limit switch to the flap 
system to prevent over-travel. This Service Bulletin also installs a switch ramp on the flap 
actuator to improve reliability and simplify rigging of the take-off position switch. 
2 REFERENCES:  
Epic E1000 Aircraft Maintenance Manual P/N SK05000000 
3 WARRANTY: 
For aircraft under warranty, parts and labor will be covered by Epic Aircraft, LLC if the work is 
performed within the compliance period and by a properly certificated Airframe and Power Plant 
mechanic or FAA approved repair station. 
4 APPROVAL: 
The engineering aspects of this service document have been shown to comply with the 
applicable Federal Aviation Regulations and are FAA approved. 
5 REVISION: 
B – If the original issue or revision A of this service bulletin was complied with, compliance with 
revision B is not required. 
• Updated serial number effectivity. 
• Updated procedure and graphics for dual set screw full switch block installation. 
• Added Loctite requirement to switch bar adjustments. 
• Added switch bar adjustment option to step 10.g.

### Page 2

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 2 of 15 
 
 
6 TOOLS: 
No. Description Qty Epic Aircraft 
Supplied 
Customer 
Supplied 
1. Common hand tools. A/R ☐ ☒ 
2. TK51600002I Flap Rig Board 1 ☐ ☒ 
7 PARTS/MATERIALS: 
No. Part Number Description Qty Epic Aircraft 
Supplied 
Customer 
Supplied 
1. PK27504311 Limit Switch Ramp, Flap 
Actuator 
1 ☒ ☐ 
2. AN3-5A Bolt, 10-32 X 21/32" Undrilled 1 ☒ ☐ 
3. NAS1149F0332P Washer, Flat #10 X .032 2 ☒  ☐ 
4. MS21044N3 Nut, Self-Locking, Steel 10-32 1 ☒ ☐ 
5. PK27504315 Switch Block, Dual, Flaps 1 ☒ ☐ 
6. MS51973-42 Setscrew, Hex Socket, Cone 
Point Ø .190-24 X .375 
1 ☒ ☐ 
7. V7-1C17E9-201 Switch, Miniature, 15.1 Amps, 
Honeywell 
1 ☒ ☐ 
8. MS35206-323 Screw, Machine-Pan Head, 
Cross-Recessed, Carbon 
Steel, Cadmium Plated, Unc-2a 
2 ☒ ☐ 
9. MS35333-36 Washer, Lock, Flat-Internal 
Tooth 
2 ☒  ☐ 
10. AK27506000 Assy, Flap Secondary Limit 
Relay 
1 ☒ ☐ 
11. HK25100072 Harness Assy, Flap Actuator To 
Secondary Flap Full Switch 
1 ☒ ☐ 
12. HK25100076 Harness Assy, Flap Full 
Secondary Switch 
1 ☒ ☐ 
13. MS27488-20-2 Sealing Plug 5 ☒ ☐ 
14. Loctite 222 or 242 Threadlocker A/R ☒ ☐ 
15. 48-7191 Amphenol Connector 1 ☒ ☐ 
16. M39029/32-248 Contact Socket 16-20 AWG 
Crimp 
1 ☒ ☐ 
17. M39029/31-229 Contact Pin 16-20 AWG Crimp 1 ☒ ☐

### Page 3

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 3 of 15 
 
 
8 INSTRUCTIONS: 
 
1. Check flap travels (refer to Epic E1000 Aircraft Maintenance Manual, PN SK05000000, 
chapter 27-50). 
NOTE: Put the flaps in the UP or T/O position before proceeding 
to the next steps. 
 
2. Set the BATT 1 and BATT 2 switches to OFF. 
3. Disconnect external electrical power from the airplane (refer to Epic E1000 Aircraft 
Maintenance Manual, PN SK05000000, chapter 24-40). 
4. Remove the left belly panel and wheel well liner to access the flap actuator (refer to Epic 
E1000 Aircraft Maintenance Manual, PN SK05000000, chapter 57-10). 
5. Install the secondary limit switch as follows:  
a. Mark the position of the full limit switch block. Loosen the set screw that attaches 
the full limit switch block to the switch bar. Remove the switch block and full limit 
switch. 
b. Remove the screws and washers that attach the full limit switch to the switch 
block. Remove the switch from the switch block and set it aside for re-installation. 
Discard the switch block (refer to figure 1). 
c. Install the retained limit switch on the dual full switch block with the screws and 
washers. Torque the screws to 1 – 2 in-lbs. 
d. Install the secondary limit switch on the dual full switch block with the screws and 
washers. Torque the screws to 1 – 2 in-lbs. 
e. Install the dual full switch block and switches on the switch bar in the position 
previously marked using only one setscrew without Loctite. (refer to figure 2). 
6. Install the Flap Secondary Full Limit Switch Relay as follows (refer to figure 3): 
a. Remove the inboard-aft bolt, washers, and nut from the hydraulic accumulator. 
b. Put the secondary full limit switch relay and bracket assembly in position on the 
accumulator. 
c. Install the bolt, washers, and nut, torque the nut to 20 – 25 in-lbs. 
7. Install the HK25100072 harness as follows:  
a. Disconnect J101 from P101 on the flap actuator. 
b. Connect 1J101 on HK25100072 to P101. 
c. Connect 1P101 on HK25100072 to J101 on the flap actuator. 
d. Connect P556 on HK25100072 to J556 on the secondary switch relay.

### Page 4

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 4 of 15 
 
 
e. Connect the terminals on HK25100076 to the secondary limit switch as follows: 
i. Connect S228A-C to the C terminal on the switch. 
ii. Connect S228A-NO to the NO terminal on the switch. 
f. Connect P563 on HK25100072 to J563 on HK25100076. 
g. Install Connector P557/J557 as follows: 
i. Splice the J557/K2310165D-16N harness into wire K2310165C-16N on 
harness HK25100009 using the 48-7191 connector, M39029/32-248 pin, 
and M39029/31-229 socket. Identify the connector as SP1014. Reinstall 
the chafe protection. 
NOTE: Splices must be staggered and within 8” of the connector. 
 
ii. Connect P557 on HK25100072 to J557. 
NOTE: Make sure there is a drip loop in the harness, refer to 
figure 4. 
 
8. Install the limit switch ramp on the ballnut using the AN3-5A bolt, (2) NAS1149F0332P 
washers, and MS21044N3 nut. 
9. Make sure the center ramp is aligned with the UP, T/O, and primary FULL limit switches. 
Torque the nut to 20 – 25 in-lbs. (refer to figure 4). 
NOTE: The switch bar may be rotated to improve switch 
alignment with the ballnut and switch ramp. Apply Loctite 222 or 
242 to the threads and torque the switch bar jam nut to 110 – 170 
in-lbs. after adjustments are made.  
 
10. Adjust the limit switches as follows (refer to figure 4): 
a. Connect external electrical power to the airplane (refer to Epic E1000 Aircraft 
Maintenance Manual, PN SK05000000, chapter 24-40). 
b. Set the BATT 1 and BATT 2 switches to ON. 
c. Put the flap rig board (P/N TK51600002I) in position on the wing aligned with the 
center flap hinge. 
 
CAUTION: The flap preload must be distributed over a minimum 
area of 1 in2 applied at a span wise distance of 6” inboard of the 
center flap hinge. It may be necessary to shake any remaining 
system compliance out in the retract direction to ensure the 
preload is effective.

### Page 5

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 5 of 15 
 
 
NOTE: Keep the preload applied to the flaps while making 
microswitch adjustments to assure correct travels are achieved. 
 
d. Apply a preload of 55 to 65 lb. to the flaps in the retract direction. 
e. Set the flaps to UP.  
i. Make sure the gap between the ball nut and jackscrew stop is .03” 
minimum and the gap between the flap forks and the spar cap is .05” 
minimum in the UP position. If the minimum gap is not met, the switch 
holder may be adjusted by loosening the set screw and moving the switch 
holder. Do not remove the set screw completely. If adjustments are 
made, torque the set screw to 12-15 in-lbs. If the up-limit switch is 
adjusted to get the correct gap, the flaps may need to be faired to the 
wing using the pushrods (refer to Epic E1000 Aircraft Maintenance 
Manual, PN SK05000000, chapter 27-50). 
f. Set the flaps to T/O. 
i. The addition of the ramp may change the actuation point for the T/O 
switch. Verify correct travel and adjust as needed. If adjustment is 
needed, the switch holder may be adjusted by loosening the set screw 
and moving the switch holder. Do not remove the set screw completely. If 
adjustments are made, torque the set screw to 12-15 in-lbs. 
g. Set the flaps to FULL.  
i. Make sure the gap between the ball nut and jackscrew stop is a 
maximum of 5.80” in the FULL position, (refer to Figure 4). 
NOTE: Both the primary and secondary full limit switches must 
stop the flaps within the travel limits, 42.8° - 43.4°. Keeping the 
secondary limit switch travel in spec will be easier if the primary 
switch is adjusted to the lower end of the travel limit. 
 
ii. Adjust the switch ramp as needed so the primary full limit switch activates 
just before the secondary full limit switch. 
NOTE: The switch bar can be rotated to help get correct 
engagement of both switches. Apply Loctite 222 or 242 to the 
threads and torque the switch bar jam nut to 110 – 170 in-lbs. 
after adjustments are made.

### Page 6

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 6 of 15 
 
 
iii. The addition of the ramp may change the actuation point for the primary 
full limit switch. Verify correct travel and adjust as needed. 
NOTE: If adjustments are made to the ramp or switch bar, verify 
that the ramp is still centered with the T/O and primary FULL limit 
switches. 
 
11. Torque the full limit switch block as follows: 
a. Once rigging is confirmed, install second setscrew using Loctite 222 or 242 and 
torque to 12 – 15 in-lbs.  
b. Remove first setscrew and apply Loctite 222 or 242. Reinstall and torque to 12 – 
15 in-lbs. 
c. Verify torque on second setscrew, and then re-verify torque on first setscrew. 
Repeat until both setscrews meet torque requirements. 
NOTE: Bending the ramp for best rigging is acceptable, refer to 
figure 5 for examples. Make sure the ramp does not exceed the 
height of the actuator ballnut. The tab of the ramp shall remain in 
contact with the actuator ballnut and must not be in cavity in the 
ballnut, refer to figure 6. 
 
12. Check the flap to wing clearances in all three positions and adjust rigging if needed to 
provide the correct clearances. All travels must stay within the provided travel limits 
(refer to Epic E1000 Aircraft Maintenance Manual, PN SK05000000, chapter 27-00). 
NOTE: Contact Epic Aircraft if clearance and travel limits cannot 
be met. 
 
13. Test the primary and secondary full limit switches as follows: 
a. Set the flaps to UP or T/O. 
b. Pull the FLAPS CTRL circuit breaker. 
c. Disconnect the electrical connections from the primary full limit switch. 
d. Reset the FLAPS CTRL circuit breaker. 
e. Set the flaps to the FULL position, make sure the travel is 42.8° - 43.4° on the 
secondary limit switch. 
NOTE: The FLAPS FAIL CAS message will illuminate with the 
primary full limit switch disconnected.

### Page 7

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 7 of 15 
 
 
f. Set the flaps to UP or T/O. 
g. Pull the FLAPS CTRL circuit breaker. 
h. Connect the electrical connections to the primary full limit switch. 
i. Reset the FLAPS CTRL circuit breaker. 
j. Set the flaps to the FULL position, make sure the travel is 42.8° - 43.4° on the 
primary limit switch. 
k. Visually confirm the flap FULL primary limit switch engages before the secondary 
FULL limit switch when transitioning from flaps UP/ or T/O to flaps FULL. 
l. Adjust the switch ramp and switches as needed to get the correct travel. 
m. Set the flaps to UP. Make sure the FLAPS FAIL CAS message does not appear. 
14. Remove the flap rig board (P/N TK51600002I). 
15. Disconnect external electrical power from the airplane (refer to Epic E1000 Aircraft 
Maintenance Manual, PN SK05000000, chapter 24-40). 
16. Install the left belly panel and wheel well liner (refer to Epic E1000 Aircraft Maintenance 
Manual, PN SK05000000, chapter 57-10).

### Page 8

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 8 of 15 
 
 
FIGURE 1: Flap Secondary Full Limit Switch 
 
 
Switch block, remove and 
discard. 
Full limit switch, remove and 
retain. 
A 
A 
Ballnut 
Switch Bar

### Page 9

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 9 of 15 
 
 
FIGURE 2: Flap Secondary Full Limit Switch 
 
 
 
 
Primary Limit Switch 
Limit Switch Ramp 
Secondary Full Limit Switch 
 
A 
A 
Dual Switch Block Set Screws 
Switch Bar 
Switch Bar 
Jam Nut 
Ballnut

### Page 10

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 10 of 15 
 
 
FIGURE 3: Flap Secondary Full Limit Switch  
 
 
   
Secondary Full 
Limit Switch 
Relay and 
Bracket Assembly 
Hydraulic 
Accumulator (Ref.) 
Retain and reuse 
the existing bolt, 
washers, and nut. 
FWD 
Make sure there is a drip 
loop in the harness. 
A 
A

### Page 11

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 11 of 15 
 
 
FIGURE 4: Flap Secondary Full Limit Switch 
 
 
  
5.80”  
Max  
.03” Min 
Make sure the ramp 
does not exceed the height of 
the actuator ballnut. 
Flaps at FULL position. 
Flaps at UP position. 
The switch ramp may be bent 
to get the best contact with 
the switches. See Figure 6 for 
examples. The switch ramp 
must rest above the cavity in 
the ballnut. See Figure 7. 
Position the ramp 
approximately .09” from the 
forward edge of the ballnut for 
initial rigging. The ramp can 
be moved forward or aft to 
improve switch contact. See 
figure 6 for examples. 
Ballnut (ref.)

### Page 12

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 12 of 15 
 
 
FIGURE 5: Flap Secondary Full Limit Switch 
 
 
Examples of acceptable manipulation of the switch ramp. 
 
 
 
Examples of acceptable positions of the switch ramp on the ballnut.

### Page 13

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 13 of 15 
 
 
FIGURE 6: Flap Secondary Full Limit Switch 
 
 
 
 
The switch ramp must rest above the cavity in the ballnut. Damage to the switches may occur if 
the ramp is positioned in the cavity. 
  
Ballnut  
Switch 
Ramp 
Cavity

### Page 14

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 14 of 15 
 
 
9 WEIGHT AND BALANCE:  
Negligible 
10 PUBLICATIONS AFFECTED:  
Epic E1000 Aircraft Maintenance Manual P/N SK05000000 
Epic E1000 Illustrated Parts Catalog, P/N SK05000004 
11 RECORD COMPLIANCE: 
Make appropriate entry in airplane maintenance records.

### Page 15

Service Bulletin SB-0034 
 
Epic Aircraft, LLC  22590 Nelson Road  Bend OR 97701 
Phone:  541-318-8849    Fax:  541-382-5125    Web:  www.epicaircraft.com 
 
Issued Revised Revision Page 
12-22-2022 xx-xx-2022 B Page 15 of 15 
 
 
Appendix A: Compliance Letter 
 
Please complete and mail this form to Customersupport@epicaircraft.com 
 
 
This is to certify that I have completed the work in accordance with the Epic Aircraft, LLC Service 
Bulletin. 
 
 
Aircraft Owner Information: 
Date: _____________   Aircraft Serial Number:  _______  Aircraft Reg. Number: __________ 
Owner’s Name: _____________________________ 
Maintenance Entity Information 
Name of Shop Performing the work: ____________________________________________ 
 
Name of Person(s) Performing inspection and/or work: ______________________________ 
 
Phone Number:   __________________ Email: ____________________________________

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
