# Fokker Service Bulletin SBF100-51-021: No revision named

- Rights: © Fokker. Filed by the FAA in regulations.gov docket FAA-2014-0492; AD 2015-12-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Fokker Service Bulletin SBF100-51-021](https://openairdocs.org/service-documents/fokker/sbf100-51-021.md)
- Title as filed: U.S. DOT/FAA - SBF100-51-021
- Pages: 25
- PDF: https://openairdocs.org/files/sha256/cb/09/cb0979e6b3d530a560704154cc2c1ef74608566063255ad92555fa851eca626b
- Page: https://openairdocs.org/service-documents/fokker/sbf100-51-021/file/cb0979e6b3d5

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin 
Fokker 70/100 
 
Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Revision - - - - - - - - - - - - - - - - - 
Page 18 19 20               
Revision - - -               
Attachments PLL and PLS. For a detailed listing refer to page 6. 
Apr 23/13 SBF100-51-021 
 Page 1 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
STANDARD PRACTICES AND STRUCTURES-GENERAL 
General - The Introduction of Drain Tubes on the Center Wing Rear Spar 
1. Planning Information  
A. Effectivity 
(1) F28 Mark 0070/0100 aircraft serial numbers: 
11244 thru 11585 
B. Concurrent Requirements 
(1) Not applicable. 
C. Reason 
(1) In case of a water accumulation on the top of the center wing torsion box inside the 
cabin (zones 171 and 172), the water drains through the existing drain holes/gaps in 
the web plates on top of  the center wing rear spar via the center wing rear spar area 
on the aileron control cables. With the freezing temperatures normally encountered 
during flight ice can accumulate on the aileron control cables resulting in limited 
aileron control.  
 
This modification provides drainage of the area on the top of the center wing torsion 
box in a location where drain water can not affect the aileron control.

### Page 2

Service Bulletin 
Fokker 70/100 
 
SBF100-51-021 Apr 23/13 
Page 2  
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
D. Description 
(1) This Service Bulletin is divided into two parts as follows: 
Part 1: The Installation of Water Drain Tubes on the Center Wing Rear Spar in 
Aircraft with Center Wing Bag Tanks (Applicable to Aircraft Serial Numbers 
11244 thru 11441) 
This Part tells you how to: 
- remove the passenger seats at the location of the modification; 
- remove the carpet at the location of the modification; 
- remove the floor panels at the location of the modification; 
- clean the area of the modification; 
- prepare the water drain tube feed through holes in the affected  
web plates on top of the center wing rear spar; 
- install the water drain tubes and identification placards; 
- seal the existing drain gaps on top of the center wing torsion box; 
- reinstall the removed floor panels; 
- reinstall the removed carpet; 
- reinstall the removed passenger seats. 
Part 2: The Installation of Water Drain Tubes on the Center Wing Rear Spar in 
Aircraft with an Integral Center Wing Tank or Provisions for an Integral 
Center Wing Tank (Applicable to Aircraft Serial Numbers 11442 thru 11585) 
This Part tells you how to: 
- remove the passenger seats at the location of the modification; 
- remove the carpet at the location of the modification; 
- remove the floor panels at the location of the modification; 
- clean the area of the modification; 
- prepare the water drain tube feed through holes in the affected web 
plates on top of the center wing rear spar; 
- install the water drain tubes and identification placards; 
- reinstall the removed floor panels; 
- reinstall the removed carpet; 
- reinstall the removed passenger seats. 
E. Compliance 
(1) Recommended. 
 
Fokker Services recommends the accomplishment of this Service Bulletin within 3 
years after the date of issue of this Service Bulletin. 
NOTE: It is expected that EASA will issue an Airworthiness Directive (AD) with 
respect to this subject with the same compliance terms. Refer to the EASA 
website for the publication of a Proposed Airworthiness Directive for 
comments.

### Page 3

Service Bulletin 
Fokker 70/100 
 
Apr 23/13 SBF100-51-021 
 Page 3 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
F. Approval 
(1) The technical content of this document is approved under the authority of DOA nr. 
EASA.21J.059. 
G. Manpower 
(1) Approximately 8,0 man-hours are necessary to do Part 1 or Part 2 of this Service 
Bulletin on one aircraft. 
 
This table of manpower will help you to schedule and do this Service Bulletin: 
 
Instructions Men Man-hours Elapsed time 
(hours) 
Removal 2 2,0 2,0 
Modification 
Inspection 2 4,0 4,0 
Installation 2 2.0 2,0 
Testing - - - 
Total  8,0 8,0 
NOTE: This estimate does not include the time necessary for the paint to dry 
and/or the sealant to cure. 
(2) The estimated hours are for direct labor done by experienced personnel. They are 
calculated based on the conditions given in SBF100-00-001 (Service Bulletin 
Introduction, section 2.C., "Manpower"). 
H. Weight and Balance 
(1) Weight change: None 
Index change: None. 
I. Electrical Load Data 
(1) Not changed. 
J. Software Accomplishment Summary 
(1) Not applicable.

### Page 4

Service Bulletin 
Fokker 70/100 
 
SBF100-51-021 Apr 23/13 
Page 4  
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
K. References 
(1) Fokker 70/100 Aircraft Maintenance Manual (AMM) 
Fokker 70/100 Structural Repair Manual (SRM) 
Fokker 70/100 Illustrated Parts Catalog (IPC) 
Fokker Consumable Material List (CML) 
Fokker Standards & Process Manual (SPM) 
Fokker internal reference(s): 
 - ECR 15937 
 - EMI 90523. 
L. Publications Affected 
(1) This SB affects the publications listed below: 
(a) Maintenance Documentation  
 
- Fokker 70/100 Illustrated Parts Catalog (IPC) - chapter 11-21 
- chapter 27-64 
NOTE: See attached Manual Change Notification MCNM F100-160. 
(b) Maintenance Programs  
 
Not affected. 
(c) Special Instructions for Continued Airworthiness (ICA)  
 
The effect of this Service Bulletin on the special ICA is as follows: 
  YES  NO  
- Electrical Wiring Interconnection System (EWIS) - X 
- Fokker 70/100 Airworthiness Limitations Section (ALS):   
 • Fuel Tank Safety (FTS) - X 
 • Damage Tolerance of Fatigue Critical Structure - X 
 • Certification Maintenance Requirements (CMR) - X 
NOTE: If “YES”, when not already incorporated, the changed ICA will be 
incorporated in the MRB, the Airworthiness Limitations Section (ALS) 
and/or the AMM document(s) within one calendar year from the date of 
issue of this Service Bulletin. Until then, no actions are required. 
(d) Operational Documentation  
 
Not affected. 
(2) Report to Fokker Services that this SB has been carried out on the applicable aircraft. 
(3) You have the possibility to send your SB feedback to Fokker Services per “Reporting 
Quality Form”. This form is located on the last SB page.

### Page 5

Service Bulletin 
Fokker 70/100 
 
Apr 23/13 SBF100-51-021 
 Page 5 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
(4) For incorporation of this Service Bulletin in your documentation refer to 
SBF100-00-001 (Service Bulletin Introduction, section 4 “Incorporation of Service 
Bulletins in Documentation of Fokker Services”). 
(5) Accomplishment of this SB is only complete with incorporation of the manual 
change(s), per the ref. MCNM/MCNO, Temporary Revision or General Revision. 
M. Interchangeability or Intermixability of Parts 
(1) The interchangeability of the parts is as follows: 
 
New Part Number Keyword  Old Part Number  Interchangeability  
AS21919WCE4 Clamp MS21919WCE4 Two-way 
NAS6603-10 Bolt NAS1303-10 Two-way 
NAS6603-11 Bolt NAS1303-11 Two-way 
NAS6603-13 Bolt NAS1303-13 Two-way 
NAS6603-17 Bolt NAS1303-17 Two-way

### Page 6

Service Bulletin 
Fokker 70/100 
 
SBF100-51-021 Apr 23/13 
Page 6  
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
2. Material Information  
A. Material – Price and Availability 
(1) You can order the necessary parts as mod kits SB10051021-XU-A and  
SB10051021-XU-B. 
(2) You can contact your Fokker Services Customer Support Manager for the price and 
lead-time of this mod kit. 
B. Material Required 
(1) The parts, which are necessary to complete this Service Bulletin on 1 aircraft and are 
not part of the mod kit are described in attachment Part List Local (PLL). 
 
Material List Issue  Description  Aircraft Effectivity  
SB10051021-XU-A B Parts List Local (PLL) 11244 thru 11261 and 
11268 thru 11275 
SB10051021-XU-B A Parts List Local (PLL) 11262 thru 11267 and 
11276 thru 11585 
(2) The mod kit parts, which are necessary to do this Service Bulletin on 1 aircraft are 
described in attachment Part List Supply (PLS). 
 
Material List Issue  Description  Aircraft Effectivity  
SB10051021-XU-A B Parts List Supply (PLS) 11244 thru 11261 and 
11268 thru 11275 
SB10051021-XU-B A Parts List Supply (PLS) 11262 thru 11267 and 
11276 thru 11585 
C. Tooling – Price and Availability 
(1) Not applicable. 
D. Drawings Required 
(1) Not applicable.

### Page 7

Service Bulletin 
Fokker 70/100 
 
Apr 23/13 SBF100-51-021 
 Page 7 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
3. Accomplishment Instructions  
 
General: 
- For CML material number references, refer to “MyFokkerFleet.com/Documentation” and  
select CML. 
- For Standards and Process Manual (SPM) references, refer to 
“MyFokkerFleet.com/Documentation” and select SPM. 
- For the application of Alodine 1201 (Fk13-003D), refer to the AMM, chapter 51-22-00. 
- For the application of sealing compound PS-870A (Fk09-016A) refer to the AMM,  
chapter 51-23-00. 
- For the removal/installation of solid rivets, refer to the SRM, chapter 51-40-02. 
- For the application of Primer and Paint, refer to the AMM, chapter 51-21-00. 
- For drilling and dimpling procedures, refer to the SRM, chapter 51-21-02. 
WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE MATERIALS. OBEY 
THE INSTRUCTIONS AND MANUFACTURER'S HEALTH AND SAFETY 
INSTRUCTIONS. 
Part 1: The Installation of Water Drain Tubes on the Center Wing Rear Spar in Aircraft with 
Center Wing Bag Tanks (Applicable to Aircraft Serial Numbers 11244 thru 11441) 
A. Preparation 
Refer to figure 1. 
(1) Remove the passenger seats on the LH and RH side of the cabin at the location 
above the center wing section (zone 171 and 172) where the outboard floor panels 
have to be removed. Refer to AMM Task 25-21-01-000-8XX-X. 
(2) Remove the carpet on the LH and RH side of the cabin at the location above the 
center wing section (zone 171 and 172) where the outboard floor panels have to be 
removed. Refer to AMM Task 25-25-00-000-8XX-X. 
(3) Remove floor panels 281BZ and 282CZ as indicated in figure 1 per  
AMM Task 53-71-01-000-8XX-X. 
Refer to figure 2. 
(4) Clean the center wing area at the location of the modification, including the existing 
drain gaps. Use: 
- AR Lint-free cloth  Fk05-044 
- AR Methyl Ethyl Ketone (or equivalent)  Fk11-003

### Page 8

Service Bulletin 
Fokker 70/100 
 
SBF100-51-021 Apr 23/13 
Page 8  
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
B. Modification 
Refer to figure 2. 
(1) Remove the rivet on the LH and RH side as indicated in figure 2 and enlarge the rivet 
holes to 7.0 (-0/+0.2) mm diameter. 
(2) Treat the bare edges of both holes with conversion coating and primer. Use: 
- AR Coating, conversion Alodine 1201 Fk13-003D 
- AR Primer, Aerodur Aerodur S15/60 Fk07-008 
Refer to figures 2, 4, 5, 6, 7 and 8. 
(3) Temporarily install water drain tube pn W33021-001 on the LH side and water drain 
tube pn W33021-003 on the RH side. Use: 
- 1 Tube, LH water drain pn W33021-001  
- 1 Tube, RH water drain pn W33021-003  
NOTE: If required, carefully bend the tube to ensure a stress free fit. 
(4) Mark both tube ends at a distance of approximately 10 mm measured from the web 
plate on top of the center wing rear spar as shown in figure 6. 
(5) Cut-off the tube ends on the correct length and threat the reworked edges with 
conversion coating. Use: 
- AR Coating, conversion Alodine 1201 Fk13-003D 
(6) Remove the existing bolts and washers in the clamp blocks of the hydraulic lines on 
the LH side in the center wing rear spar area as shown in figures 4 and 7. Discard: 
- 2 Bolts pn NAS1303-10 or 
pn NAS1303-16 
Discard 
- 2 Washers pn NAS1252-10L Discard 
(7) Install the water drain tube on the LH side in the center wing rear spar area with the 
clamps as shown in figure 4, Detail X. Refer to figure 7 for applicable mounting 
hardware. Use: 
- 1 Tube, LH water drain pn W33021-001  
- 2 Clamps pn AS21919WCE4  
- 2 Bolts pn NAS6603-11 *1 
- 2 Bolts pn NAS6603-17 *2 
- 2 Washers pn NAS1252-10L  
NOTES: *1 Applicable to aircraft sn 11262 thru 11267 and 11276 thru 11441. 
 *2 Applicable to aircraft sn 11244 thru 11261 and 11268 thru 11275. 
(8) Remove the existing bolt and washer in the clamp block of the hydraulic lines on the 
RH side in the center wing rear spar area as shown in figures 4 and 7. Discard: 
- 1 Bolt pn NAS1303-10 or 
pn NAS1303-12 
Discard 
- 1 Washer pn NAS1252-10L Discard

### Page 9

Service Bulletin 
Fokker 70/100 
 
Apr 23/13 SBF100-51-021 
 Page 9 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
(9) Install the water drain tube on the RH side in the center wing rear spar area with the 
clamps and clamping blocks as shown in figure 5, Detail X and Y. Refer to figures 7 
and 8 for applicable mounting hardware for upper and lower attachment respectively. 
Use: 
- 1 Tube, RH water drain pn W33021-003  
- 2 Clamping blocks pn A71052-077  
- 2 Clamps pn AS21919WCE4  
- 2 Bolts pn NAS6603-10  
- 1 Bolt pn NAS6603-11 *1 
- 2 Bolts pn NAS6603-11 *2 
- 1 Bolt pn NAS6603-13 *1 
- 7 Washers pn NAS1252-10L  
- 3 Nuts pn MS21042L3  
NOTES: *1 Applicable to aircraft sn 11244 thru 11261 and 11268 thru 11275. 
 *2 Applicable to aircraft sn 11262 thru 11267 and 11276 thru 11441. 
(10) Apply sealing compound around both water drain tubes at the feed through holes in 
the web plates on top of the center wing rear spar as shown in figure 6. Use: 
- AR Sealing compound  pn PS870A Fk09-016A 
(11) Close the existing drain gaps on top of the center wing torsion box with sealing 
compound as shown in figure 2. Use: 
- AR Sealing compound  pn PS870A Fk09-016A 
(12) Install the water drain tube identification placards on the locations shown in figures 4 
and 5, Detail B. Use: 
- 2 Placards, identification pn W33022-001  
(13) Apply a protective layer on the identification placards. Use: 
- AR Coating, protective pn Nycote 88 Fk09-008 
C. Completion of the work 
Refer to figure 1. 
(1) Reinstall floor panels 281BZ and 282CZ as indicated in figure 1 per  
AMM Task 53-71-01-400-8XX-X. 
(2) Reinstall the carpet on the LH and RH side of the cabin at the location above the 
center wing section (zone 171 and 172) where the outboard floor panels have been 
removed. Refer to AMM Task 25-25-00-400-8XX-X. 
(3) Reinstall the passenger seats on the LH and RH side of the cabin at the location 
above the center wing section (zone 171 and 172) where the outboard floor panels 
have been removed. Refer to AMM Task 25-21-01-400-8XX-X.

### Page 10

Service Bulletin 
Fokker 70/100 
 
SBF100-51-021 Apr 23/13 
Page 10  
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
Part 2: The Installation of Water Drain Tubes on the Center Wing Rear Spar in Aircraft with 
an Integral Center Wing Tank or Provisions for an Integral Center Wing Tank 
(Applicable to Aircraft Serial Numbers 11442 thru 11585) 
A. Preparation 
Refer to figure 1. 
(1) Remove the passenger seats on the LH and RH side of the cabin at the location 
above the center wing section (zone 171 and 172) where the outboard floor panels 
have to be removed. Refer to AMM Task 25-21-01-000-8XX-X. 
(2) Remove the carpet on the LH and RH side of the cabin at the location above the 
center wing section (zone 171 and 172) where the outboard floor panels have to be 
removed. Refer to AMM Task 25-25-00-000-8XX-X. 
(3) Remove floor panels 281BZ and 282CZ as indicated in figure 1 per  
AMM Task 53-71-01-000-8XX-X. 
Refer to figure 3. 
(4) Clean the center wing area at the location of the modification. Use: 
- AR Lint-free cloth  Fk05-044 
- AR Methyl Ethyl Ketone (or equivalent)  Fk11-003 
B. Modification 
Refer to figure 3. 
(1) Carefully enlarge the existing drain holes to 7.0 (-0/+0.2) mm diameter on the LH and 
RH side as indicated in figure 3. 
NOTE: Do not damage the upper side of the center wing section. 
(2) Treat the bare edges of both holes with conversion coating and primer. Use: 
- AR Coating, conversion Alodine 1201 Fk13-003D 
- AR Primer Aerodur S15/60 Fk07-008 
Refer to figures 3, 4, 5, 6, 7 and 8. 
(3) Temporarily install water drain tube pn W33021-001 on the LH side and water drain 
tube pn W33021-003 on the RH side. Use: 
- 1 Tube, LH water drain pn W33021-001  
- 1 Tube, RH water drain pn W33021-003  
NOTE: If required, carefully bend the tube to ensure a stress free fit. 
(4) Mark the tube ends at a distance of approximately 10 mm measured from web plate 
on top of the center wing rear spar as shown in figure 6.

### Page 11

Service Bulletin 
Fokker 70/100 
 
Apr 23/13 SBF100-51-021 
 Page 11 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
(5) Cut-off the tube ends on the correct length and threat the reworked edges with 
conversion coating. Use: 
- AR Coating, conversion Alodine 1201 Fk13-003D 
(6) Remove the existing bolts and washers in the clamp blocks of the hydraulic lines on 
the LH side in the center wing rear spar area as shown in figures 4 and 7. Discard: 
- 2 Bolts pn NAS1303-10 Discard 
- 2 Washers pn NAS1252-10L Discard 
(7) Install the water drain tube on the LH side in the center wing rear spar area with the 
clamps as shown in figure 4, Detail X. Refer to figure 7 for the applicable mounting 
hardware. Use: 
- 1 Tube, LH water drain pn W33021-001  
- 2 Clamps pn AS21919WCE4  
- 2 Bolts pn NAS6603-11  
- 2 Washers pn NAS1252-10L  
(8) Remove the existing bolt and washer in the clamp block of the hydraulic lines on the 
RH side in the center wing rear spar area as shown in figures 5 and 7. Discard: 
- 1 Bolt pn NAS1303-10 Discard 
- 1 Washer pn NAS1252-10L Discard 
(9) Install the water drain tube on the RH side in the center wing rear spar area with the 
clamps and clamping blocks as shown in figure 5, Detail X and Y. Refer to figures 7 
and 8 for applicable mounting hardware for the upper and lower attachment 
respectively. Use: 
- 1 Tube, RH water drain pn W33021-003  
- 2 Clamping blocks pn A71052-077  
- 2 Clamps pn AS21919WCE4  
- 2 Bolts pn NAS6603-10  
- 2 Bolts pn NAS6603-11  
- 7 Washers pn NAS1252-10L  
- 3 Nuts pn MS21042L3  
(10) Apply sealing compound around both water drain tubes at the feed through holes in 
the web plates on top of the center wing rear spar as shown in figure 6. Use: 
- AR Sealing compound  pn PS870A Fk09-016A 
(11) Install the water drain tube identification placards on the positions shown in figures 4 
and 5, Detail B. Use: 
- 2 Placards, identification pn W33022-001  
(12) Apply a protective layer on the identification placards. Use: 
- AR Coating, protective pn Nycote 88 Fk09-008

### Page 12

Service Bulletin 
Fokker 70/100 
 
SBF100-51-021 Apr 23/13 
Page 12  
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
C. Completion of the work 
Refer to figure 1. 
(1) Install floor panels 281BZ and 282CZ as indicated in figure 1 per  
AMM Task 53-71-01-400-8XX-X. 
(2) Install the carpet on the LH and RH side of the cabin at the location above the center 
wing section (zone 171 and 172) where the outboard floor panels have been 
removed. Refer to AMM Task 25-25-00-400-8XX-X. 
(3) Install the passenger seats on the LH and RH side of the cabin at the location above 
the center wing section (zone 171 and 172) where the outboard floor panels have 
been removed. Refer to AMM Task 25-21-01-400-8XX-X.

### Page 13

Service Bulletin 
Fokker 70/100 
 
Apr 23/13 SBF100-51-021 
 Page 13 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Removal of Outboard Floor Panels 261BZ and 282CZ above Zone 171 and 172 (shaded area). 
Figure 1

### Page 14

Service Bulletin 
Fokker 70/100 
 
SBF100-51-021 Apr 23/13 
Page 14  
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
 
 
Water Drain Tube Hole in the Web Plate on Top of the Center Wing Rear Spar  
(applicable to aircraft sn 11244 thru 11441). 
Figure 2 
 
 
Water Drain Tube Hole in the Web Plate on Top of the Center Wing Rear Spar  
(applicable to aircraft sn 11442 thru 11585). 
Figure 3

### Page 15

Service Bulletin 
Fokker 70/100 
 
Apr 23/13 SBF100-51-021 
 Page 15 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
 
 
Water Drain Tube Installation on the LH Side of the Center Wing Rear Spar. 
Figure 4 
  
Section A-A, refer to figure 6. 
Detail X, refer to figure 7.

### Page 16

Service Bulletin 
Fokker 70/100 
 
SBF100-51-021 Apr 23/13 
Page 16  
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
 
 
Water Drain Tube Installation on the RH Side of the Center Wing Rear Spar. 
Figure 5 
  
Section A-A, refer to figure 6 
Detail X, refer to figure 7 
Detail Y, refer to figure 8

### Page 17

Service Bulletin 
Fokker 70/100 
 
Apr 23/13 SBF100-51-021 
 Page 17 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
 
 
 
 
 
 
 
 
 
 
Application of Sealant around the Water Drain Tube at the Hole in the Web Plate 
on Top of the Center Wing Rear Spar  
(Section A-A of figures 4 and 5). 
Figure 6

### Page 18 (OCR)

Takker  Service Bulletin
Fokker 70/100
DETAIL X
W33021-001 LH
W33021-003 RH
Remove:
NAS1303-10 *1
NAS1303-12 *2
NAS1 303-16 *3
NAS1252-10L
Install:
AS21 91 9WCE4
NAS6603-11 *1
NAS6603-13 *2
NAS6603-17 *3
NAS1252-10L
*1 Applicable to aircraft serial numbers 11262
thru 11267 and  11276 thru 11585 (LH and RH)
*2 Applicable to aircraft serial numbers 11244
thru 11261 and 11268 thru 11275 (RH only)
*3 Applicable to aircraft serial numbers 11244
thru 11261 and 11268 thru 11275 (LH only)
Water Drain Tube Installation on the LH and RH Side according to Detail X of Figures 4 and 5.
Figure 7
SBF100-51-021  Apr 23/13
Page 18
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V. to its customers on a confidential basis subject to the provisions of an agreement
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained therein for purposes other than explicitly allowed by the aforesaid agreement, is not permittec
except with the prior written permission of Fokker Services B.V.

### Page 19

Service Bulletin 
Fokker 70/100 
 
Apr 23/13 SBF100-51-021 
 Page 19 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
 
 
 
 
 
 
 
 
 
Water Drain Tube Installation on the RH side according to Detail Y of Figure 5. 
Figure 8 
 
DETAIL Y

### Page 20

Service Bulletin Reporting Quality Form 
Fokker 70/100 
 
SBF100-51-021 Apr 23/13 
Page 20  
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted 
except with the prior written permission of Fokker Services B.V. 
Service Bulletin Reporting Quality Form 
 
Use this Service Bulletin Reporting Quality Form to tell us your perception of the quality of the Service 
Bulletin. The reported data that you provide to us will be used to analyze areas of difficulties and to take 
corrective actions to further improve the quality of our Service Bulletins. 
We thank you for the time you have taken in completing this form. 
 
* Rate the scale of 1 to 4, with 1 the lowest score and 4 the highest score. 
Chapters * 1 2 3 4 
a)  Quality rating of this SB (overall) □ □ □ □ 
b)  Quality rating of the Planning Information □ □ □ □ 
c)  Quality rating of the Material Information □ □ □ □ 
d)  Quality rating of the Accomplishment Instructions □ □ □ □ 
e)  Quality rating of the Test Instructions (if applicable) □ □ □ □ 
f)  Quality rating of the Illustrations or Drawings (if applicable) □ □ □ □ 
g)  Timely delivery of the SB □ □ □ □ 
 
If you have had difficulties with one of the chapters of this Service Bulletin and/or one of your 
rating(s) is lower than 3, please give a short description of the issue. 
 
Comments: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Operator: Date:  
 
Name / Title:  
 
 
Please return this form to: Fokker Services B.V.  
Technical Services, Quality Department 
P.O. Box 1357 
2130 EL Hoofddorp 
The Netherlands 
 
Fax: +31 (0) 88 6280111  or  Email: technicalservices@fokker.com

### Page 21

Fokker Services B.V. 
Parts List Local (PLL) 
       
       
       
 
 
 
 
 
 
 
 
All rights reserved. Reproduction or disclosure to third parties of this document or any part thereof, or the use of any 
information contained therein for purpose other than provided for by this document, is not permitted without prior and 
express written permission of Fokker Services B.V. 
 
EASA approved procedure for electronic sign-off   temp. 9083 08-11  
 
 
Keyword : MODKIT
Description : DRAIN TUBES
Program : F28
Rel. to EB/SB : SBF100-51-021
Rel. to EB/SB Issue : -
Part Release Date : 10-04-2013
Part : SB10051021-XU-B
Revision : A,1
Status : Released
Assembly
Part Number Rev Seq Keyword Description
SB10051021-XU-B A 1 MODKIT DRAIN TUBES
Assembly Structure
Qty UoM Part Number Keyword Info Old Part Number Instructions/Disposition
AR 5-701-1 PRIMER CML Fk07-008 - Local Source
AR 5-721-1-064095 ENAMEL CML Fk07-027 - Local Source
AR 5-943-2 COMPOUND CML Fk09-008 - Local Source
AR 5-951-6 SEALANT CML Fk09-016A - Local Source
AR AL0DINE1201 COATING CML Fk13-003D - Local Source
Full Part Numbers
Part Number Full Part Number
AL0DINE1201 ALODINE1201
Page 1 of 1

### Page 22

Fokker Services B.V. 
Parts List Supply (PLS) 
       
       
       
 
 
 
 
 
 
 
 
All rights reserved. Reproduction or disclosure to third parties of this document or any part thereof, or the use of any 
information contained therein for purpose other than provided for by this document, is not permitted without prior and 
express written permission of Fokker Services B.V. 
 
EASA approved procedure for electronic sign-off   temp. 9084 08-11  
 
 
Keyword : MODKIT
Description : DRAIN TUBES
Program : F28
Rel. to EB/SB : SBF100-51-021
Rel. to EB/SB Issue : -
Part Release Date : 10-04-2013
Part : SB10051021-XU-B
Revision : A,1
Status : Released
Assembly
Part Number Rev Seq Keyword Description
SB10051021-XU-B A 1 MODKIT DRAIN TUBES
Assembly Structure
Qty UoM Part Number Keyword Info Old Part Number Instructions/Disposition
2 ea A71052-077 BLOCK - - -
4 ea AS21919WCE4 CLAMP - - -
3 ea MS21042L3 NUT - - -
9 ea NAS1252-10L WASHER - - -
2 ea NAS6603-10 BOLT - - -
4 ea NAS6603-11 BOLT - NAS1303-10 -
1 ea W33021-001 TUBE - - -
1 ea W33021-003 TUBE - - -
2 ea W33022-001 PLACARD - - -
Page 1 of 1

### Page 23

Fokker Services B.V. 
Parts List Local (PLL) 
       
       
       
 
 
 
 
 
 
 
 
All rights reserved. Reproduction or disclosure to third parties of this document or any part thereof, or the use of any 
information contained therein for purpose other than provided for by this document, is not permitted without prior and 
express written permission of Fokker Services B.V. 
 
EASA approved procedure for electronic sign-off   temp. 9083 08-11  
 
 
Keyword : MODKIT
Description : DRAIN TUBES
Program : F28
Rel. to EB/SB : SBF100-51-021
Rel. to EB/SB Issue : -
Part Release Date : 10-04-2013
Part : SB10051021-XU-A
Revision : B,1
Status : Released
Assembly
Part Number Rev Seq Keyword Description
SB10051021-XU-A B 1 MODKIT DRAIN TUBES
Assembly Structure
Qty UoM Part Number Keyword Info Old Part Number Instructions/Disposition
AR 5-701-1 PRIMER CML Fk07-008 - Local Source
AR 5-721-1-064095 ENAMEL CML Fk07-027 - Local Source
AR 5-943-2 COMPOUND CML Fk09-008 - Local Source
AR 5-951-6 SEALANT CML Fk09-016A - Local Source
AR AL0DINE1201 COATING CML Fk13-003D - Local Source
Full Part Numbers
Part Number Full Part Number
AL0DINE1201 ALODINE1201
Page 1 of 1

### Page 24

Fokker Services B.V. 
Parts List Supply (PLS) 
       
       
       
 
 
 
 
 
 
 
 
All rights reserved. Reproduction or disclosure to third parties of this document or any part thereof, or the use of any 
information contained therein for purpose other than provided for by this document, is not permitted without prior and 
express written permission of Fokker Services B.V. 
 
EASA approved procedure for electronic sign-off   temp. 9084 08-11  
 
 
Keyword : MODKIT
Description : DRAIN TUBES
Program : F28
Rel. to EB/SB : SBF100-51-021
Rel. to EB/SB Issue : -
Part Release Date : 10-04-2013
Part : SB10051021-XU-A
Revision : B,1
Status : Released
Assembly
Part Number Rev Seq Keyword Description
SB10051021-XU-A B 1 MODKIT DRAIN TUBES
Assembly Structure
Qty UoM Part Number Keyword Info Old Part Number Instructions/Disposition
2 ea A71052-077 BLOCK - - -
4 ea AS21919WCE4 CLAMP - - -
3 ea MS21042L3 NUT - - -
9 ea NAS1252-10L WASHER - - -
2 ea NAS6603-10 BOLT - - -
1 ea NAS6603-11 BOLT - - -
1 ea NAS6603-13 BOLT - NAS1302-12 -
2 ea NAS6603-17 BOLT - NAS1303-16 -
1 ea W33021-001 TUBE - - -
1 ea W33021-003 TUBE - - -
2 ea W33022-001 PLACARD - - -
Page 1 of 1

### Page 25

Manual Change Notification – Maintenance Documentation 
Fokker 70/100 
APR 23/13 MCNM F100-160 
 Page 1 of 1 
MCNM-F100-160 
 
Subject : Drains - Introduction of Water Drain Tubes on the Rear-Spar of the Center-Wing. 
 
Reason : This MCN is issued to provide you with the changes on the content(s) of the affected 
manual(s), due to the introduction of SBF100-51-021. 
 
Effectivity : Refer to SBF100-51-021. 
 
Compliance : Once you have determined the applicability of this MCN for one or more of your 
aircraft, incorporate this information into the applicable manual(s). 
 
Publications  
affected : The Illustrated Parts Catalogue (IPC). 
   
 
Change Note : IPC 
 
  Update IPC 11-21-02-30, to show: 
- The location of the two placards (Part number W33022-001) as shown on 
Figures 4 and 5 of SBF100-51-021 
- The details of the two placards (Part number W33022-001) as given on drawing 
W33022 which is attached to SBF100-51-021. 
 
  Update IPC 27-64-11-04 thru -04F (as applicable), to show: 
- The modified clamp-block installations (See Detail X) as shown on the Figures 
4, 5 and 7 of SBF100-51-021 
- The new clamp-block installation (See Detail Y) as shown on the Figures 5 and 
8 of SBF100-51-021. 
 
  Add a new Figure in IPC Chapter 53-78-10, to introduce: 
- The new drain tubes (Part numbers W33021-001 and W33021-003) on the rear-
spar of the center-wing (Zone 170/180), as shown on the Figures 4 and 5 of 
SBF100-51-021 
- A reference to IPC 27-64-11-04 for the clamp-block supports. 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: If you have a Document Revision Service (DRS) with Fokker Services, this MCN 
will be included into your manuals, at the earliest opportunity.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
