# Fokker Service Bulletin SBF100-57-049: No revision named

- Rights: © Fokker. Filed by the FAA in regulations.gov docket FAA-2016-7271; AD 2016-24-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Fokker Service Bulletin SBF100-57-049](https://openairdocs.org/service-documents/fokker/sbf100-57-049.md)
- Title as filed: FAA-2016-7271_SBF100-57-049
- Pages: 24
- PDF: https://openairdocs.org/files/sha256/b2/da/b2da5f4134e5d1189f7d062127af053c69ae04fea234f123e8e20d6b9000f5e7
- Page: https://openairdocs.org/service-documents/fokker/sbf100-57-049/file/b2da5f4134e5

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Service Bulletin 
 Fokker Services B.V. 
 Prepared  Function / Note  Date 
    poutsma-sp49839     Mar 24/15 
 Colleague Check    
    doesburg-jd01812     Mar 23/15 
 Manager Final Approval    
    benthem-eb01865     Mar 24/15 
 Office of Airworthiness Approval   
    visser-hv01800     Mar 24/15 
 
 
 
 
Status:  
Released 
Revision:  
- 
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with 
the prior written permission of Fokker Services B.V. 
 
EASA approved procedure for electronic sign-off  
 
 
 
F100/70 Generic SB 
 
 
SBF100-57-049 
 
 
Revision - 
 
 
 
WINGS - TORSION BOXES 
 
 
 
 
 
The One-Time Inspection of the LH and RH Wing Rear Spar Lower Girder from WSTA 
2635 to 8700 and 9270 to 12975 and Modification of the Wing Trailing Edge Lower 
Skin Panels into Access Panels.

### Page 2

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 1 of 23  
 
1. General Information  
A. General 
 
 
 
B. Table of Contents 
 
• Section 1: General Information 
• Section 2: Planning Information 
• Section 3: Material Information 
• Section 4: Accomplishment Instructions  
• Service Bulletin Quality Reporting Form 
and attachments (if applicable): 
• List of drawings/parts lists  
• Parts List Local source (PLL)  
• Parts List Supply (PLS)  
• Required drawings 
C. Service Bulletin Revision History 
 
Revision Date (Mmm dd/yy) Reason for Revision 
- Refer to footer First Release 
 
  
 
 
WINGS - TORSION BOXES 
 
The One-Time Inspection of the LH and RH Wing Rear Spar Lower Girder from WSTA 
2635 to 8700 and 9270 to 12975 and Modification of the Wing Trailing Edge Lower Skin 
Panels into Access Panels.

### Page 3

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 2 of 23  
 
2. Planning Information  
A. Effectivity 
(1) F28 Mark 0070/0100 aircraft serial numbers: 
11244 thru 11585. 
B. Concurrent Requirements 
(1) Not applicable. 
C. Reason 
(1) An aircraft was found with heavy corrosion on the rear spar lower girder at several 
spanwise positions. Locally the corrosion damage was such that at small spots 
almost all effective thickness of the vertical flange of the lower girder was lost. 
(2) When performing the zonal inspections in zone 536 and 636 (MRB task 062505-
00-01 and 062605-00-01), the rear spar lower girder between WSTA 9270 and 
11794 is hidden from view by the inboard and outboard aileron balancing plates. 
Therefore it is possible that corrosion in this area is not found during these routine 
zonal inspections. Outside this area the rear spar lower girder is directly visible 
during the same zonal inspections. Nevertheless heavy corrosion was found in this 
area as well. 
(3) Calculations have been made on the reduction in load carrying capability of the 
wing under the relevant load cases. As a consequence it has been determined that 
the risk of presence of similar corrosion damages on other aircraft in the fleet is too 
high and therefore requires a one-time inspection for timely detection and 
correction. 
(4) For the area between WSTA 9270 and 11794 the outer wing trailing edge lower 
skin has to be removed to get access and enable inspection of the rear spar. The 
trailing edge structure and the skin panels will be modified to use these skin panels 
as removable access panels. The zonal inspection will be revised to add the new 
access panel numbers. 
(5) The area between WSTA 8700 and 9270 is excl uded from this Service Bulletin as 
this area is already covered by the detailed inspection according ALS task 572009-
00-13. However, if not already accomplished, it may be advisable to plan the first 
accomplishment of subject task simultaneously with the accomplishment of 
SBF100-57-049. 
(6) This Service Bulletin provides allowable (flyable) remaining thickness limits after 
the blend out of the possible corrosion on the outer wing rear spar lower girder 
between WSTA 2635 and 12975. These limits are not the absolute minimums. 
Smaller remaining thickness (deeper blend outs) may be allowed however must be 
evaluated on a case by case basis by Fokker Services.

### Page 4

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 3 of 23  
 
(7) For repair of the rear spar lower girder outboard WSTA 8200 Service Bulletin 
SBF100-57-050 will be issued. This Service Bulletin provides a generic repair by 
replacing (parts of) the lower girders. For repairs inboard WSTA 8200 contact 
Fokker Services for instructions. 
(8) In case of small blend out areas which do not necessitate a replacement of the 
lower girder Fokker Services can provide customized repairs consisting of local 
repair angles. 
D. Description 
(1) This Service Bulletin is divided in two Parts as follows: 
Part 1: The One-Time Inspection of the LH and RH Wing Rear Spar Lower Girder 
from WSTA 9270 to 11794 and Modification of the Wing Trailing Edge 
Lower Skin Panels into Access Panels. 
 
- Get access and prepare the inspection area. 
- Inspect the Rear Spar Lower Girder Area between WSTA 9270 and 11794. 
- Corrective actions only applicable in case corrosion is found. 
- Restore the surface protection in case paint, sealant and/or corrosion was 
removed. 
- Modification of the trailing edge rebates for installation of the skin panels as 
removable access panels. 
- Modification of the composite skin panels.  
- Installation of access panels. 
- Report your findings to Fokker Services. 
Part 2: The One-Time Inspection of the LH and RH Wing Rear Spar Lower Girder 
Area from WSTA 2635 to 8700 and 11794 to 12975. 
 
- Get access and prepare the inspection area. 
- Inspect the Rear Spar Lower Girder Area from WSTA 2635 to 8700 and 11794 
to 12975. 
- Corrective actions only applicable in case corrosion is found. 
- Restore the surface protection in case paint, sealant and/or corrosion was 
removed. 
- Installation of access panels. 
- Report your findings to Fokker Services.

### Page 5

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 4 of 23  
 
E. Compliance 
(1) Recommended 
Fokker Services recommends the accomplishment of the Parts of this Service 
Bulletin within the following periods: 
Part 1: Fokker Services recommends the accomplishment of the inspection of 
the rear spar area from WSTA 9270 to 11794 and modification of the 
wing trailing edge lower skin panels within 1 000 flight cycles or 1 year 
from the release date of this Service Bulletin, whichever comes first. 
Part 2: Fokker Services recommends the accomplishment of the inspection of 
the rear spar area from WSTA 2635 to 8700 and 11794 to 12975 within  
2 000 flight cycles or 2 years from the release date of this Service 
Bulletin, whichever comes first. 
NOTE: It is expected that EASA will issue an Airworthiness Directive (AD) with 
respect to this subject with the same compliance terms. Refer to the 
EASA website for the publication of a Proposed Airworthiness Directive 
for comments. 
F. Approval 
(1) The technical content of this document is approved under the authority of DOA ref. 
EASA.21J.059. 
G. Manpower 
(1) Approximately 23 man-hours are necessary to do Part 1 of this Service Bulletin on 
one aircraft.  
This table of manpower will help you to schedule and do this Service Bulletin: 
Elapsed time
(hours)
Removal 2 4.0 2.0
Modification
Inspection
Installation 1 3.0 3.0
Testing - - -
Total 23.0 13.0
8.0
Instructions Men Man-hours
21 6 . 0
 
NOTE: This estimate does not include the time necessary for the paint to dry 
and/or the sealant to cure.

### Page 6

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 5 of 23  
 
(2) Approximately 12 man-hours are necessary to do Part 2 of this Service Bulletin on 
one aircraft.  
This table of manpower will help you to schedule and do this Service Bulletin: 
Elapsed time
(hours)
Removal 1 5.0 5.0
Modification
Inspection
Installation 1 5.0 5.0
Testing - - -
Total 12.0 12.0
2.0
Instructions Men Man-hours
12 . 0
 
NOTE: This estimate does not include the time necessary for the paint to dry 
and/or the sealant to cure.  
(3) The estimated hours are for direct labor done by experienced personnel. They are 
calculated based on the conditions given in SBF100-00-001 (Service Bulletin 
Introduction, section 2.C., “Manpower”). 
H. Weight and Balance 
(1) Weight change: None. 
Index change: None. 
I. Electrical Load Data 
(1) Direct Current (DC) Loads: 
(a) Not changed. 
(2) Alternating Current (AC) Loads: 
(a) Not changed. 
J. Software Accomplishment Summary 
(1) Not applicable.  
K. References 
(1) Fokker 70/100 Aircraft Maintenance Manual (AMM) 
Fokker 70/100 Maintenance Planning Document (MPD) 
Fokker 70/100 Maintenance Review Board (MRB) report 
Fokker 70/100 Non-Destructive Testing (NDT) Manual 
Fokker 70/100 Structural Repair Manual (SRM) 
Fokker Consumable Material List (CML) 
Fokker Standards & Process Manual (SPM) 
Fokker 100 Service Bulletin (SB): 
- SBF100-57-050

### Page 7

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 6 of 23  
 
Fokker internal reference: 
 - ECR016183. 
L. Publications Affected 
(1) This Service Bulletin affects the publications listed below: 
(a) Maintenance Documentation  
 
- Fokker 70/100 Aircraft Maintenance Manual (AMM)  - chapter 06-30 
- Fokker 70/100 Illustrated Parts Catalog (IPC) - chapter 57-61 
(b) Maintenance Programs  
 
- Fokker 70/100 Maintenance Planning Document (MPD). 
(c) Special Instructions for Continued Airworthiness (ICA)  
The effect of this Service Bulletin on the special ICA is as follows:  
  YES NO 
- Electrical Wiring Interconnection System (EWIS) - X 
- Fokker 70/100 Airworthiness Limitations Section (ALS):   
 • Fuel Tank Safety (FTS) - X 
 • Damage Tolerance of Fatigue Critical Structure (FCS) - X 
 • Certification Maintenance Requirements (CMR) - X 
NOTE: If “YES”, when not already incorporated, the changed ICA will be 
incorporated in the MRB, the Airworthiness Limitations Section (ALS) 
and/or the AMM document(s) within one calendar year from the date 
of issue of this Service Bulletin. Until then, no actions are required. 
(d) Operational Documentation  
Not affected. 
(2) Report to Fokker Services that this Service Bulletin has been carried out on the 
applicable aircraft.  
(3) You have the possibility to send your SB feedback to Fokker Services per “Service 
Bulletin Reporting Quality Form”. This form is located on the last Service Bulletin 
page. 
(4) For incorporation of this Service Bulletin in your documentation refer to 
SBF100‑00‑001 (Service Bulletin Introduction, section 4 “Incorporation of Service 
Bulletins in Documentation of Fokker Services”). 
M. Interchangeability or Intermixability of Parts 
(1) Not applicable.

### Page 8

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 7 of 23  
 
3. Material Information  
A. Material – Price and Availability 
(1) You can order the necessary parts as mod kit SB10057049-XU-A.  
(2) You can contact your Fokker Services Customer Support Manager for the price 
and lead-time of this mod kit. 
B. Material Required 
(1) These parts, which are necessary to complete this Service Bulletin on 1 aircraft, 
are not part of the mod kit: 
 
New Part Number Qty  Keyword  Info  Old Part  Instructions/  
 * 1 *2   Number Disposition 
- AR* 3 AR Lint-free cloth Fk05-044* 4 - Local source 
2024T3 Alclad AR - Sheet t = 0.8 mm - Local source 
Aerodur Finish C21/100 AR AR Paint Fk07-027 - Local source 
Aerodur Primer S15/60 AR AR Primer Fk07-008 - Local source 
Alodine 1201 or AR AR Conversion coating Fk13-003D - Local source 
   Alodine 1132 Touch-n-Prep       Fk13-003E   
EA9396 AR - Laminating resin TH5.558/9 - Local source 
Methyl Ethyl Ketone  AR AR Cleaning solvent Fk11-003 - Local source 
MS20426AD5 16 - Solid rivet - - Local source 
NAS1097AD3 596 - Solid rivet - - Local source 
Nycote 88 AR AR Skydrol-resistant 
   coating 
Fk09-008 - Local source 
PS870A AR - Sealant Fk09-016A - Local source 
PS870B AR AR Sealant Fk09-017A - Local source 
Scotchbrite Type A Very Fine AR AR Abrasive material Fk05-007 - Local source 
NOTES: * 1  Applicable to do Part 1 of this Service Bulletin on 1 aircraft 
*2 Applicable to do Part 2 of this Service Bulletin on 1 aircraft 
*3 Use as much as necessary 
*4 Refer to the CML for material numbers. 
(2) These mod kit parts are necessary to do Part 1 of this Service Bulletin on 1 
aircraft: 
New Part Number Qty  Keyword  Info  Old Part 
Number 
Instructions/ 
Disposition 
D15003-701*5 27 Tapered plate - - - 
F0N2-1611V03-03 4 Bolt NSA5030-3-3 - - 
F0N2-1611V03-04 6 Bolt NSA5030-3-4 - - 
F0N2-1611V03-05 266 Bolt NSA5030-3-5 - - 
F0N2-1611V03-06 22 Bolt NSA5030-3-6 - - 
MS21073L3 66 Anchor nut - - - 
MS21075L3E 232 Anchor nut - - - 
NOTE: * 5 Part can also be made locally using 2024T3 Alclad sheet 170×25×2,5  
 mm. Refer to step F.(4) of Part 1 and figure 7.

### Page 9

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 8 of 23  
 
C. Tooling – Price and Availability 
(1)  Not applicable. 
D. Tooling Required 
(1) Not applicable.

### Page 10

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 9 of 23  
 
4. Accomplishment Instructions  
 
General: 
- All Accomplishment Instructions are applicable to the LH and RH wing.  Part quantities are 
provided for each wing separately. 
- For CML material number references refer to “MyFokkerFleet.com > Documentation and 
select CML” and/or AMM chapter 20-30-00. 
- For the application of sealing compound refer to AMM chapter 20-32-00 and chapter 51-
23-00.  
- For the application of Primer & Paint refer to the AMM chapter 51-21-00. 
- For the application of Alodine refer to AMM chapter 51-22-00 and SRM chapter 51-24-01. 
WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE MATERIALS. OBEY 
THE INSTRUCTIONS AND MANUFACTURER'S HEALTH AND SAFETY 
INSTRUCTIONS. 
Part 1: The One-Time Inspection of the LH and RH Wing Rear Spar Lower Girder from 
WSTA 9270 to 11794 and Modification of the Wing Trailing Edge Lower Skin Panels 
into Access Panels. 
A. Get access and prepare the inspection area. 
(1) Open access panel 536(636)GB (Fuel tank ventilation sniffle-valve). 
Refer to figures 1 and 2. 
(2) Remove the two trailing edge lower skin panels between WSTA 9270 and 11794 
connected to the rear spar. 
NOTE:  The skin panels are installed with solid rivets and Hi-Loks. Carefully 
remove them without damaging the composite skin panels.  
(3) Remove any blistered, cracked, flaking or loose paint and/or sealant from the 
vertical flange of the rear spar lower girder and lower area of the web. Use a non-
metal brush, non-metal scraper, compressed air or any suitable means. 
NOTE: For better access to the rear spar the aileron balance plate support beams 
can be removed (SRM chapter 57-57-02-05 items 280 and 310).  
B. Inspect the Rear Spar Lower Girder Area between WSTA 9270 and 11794. 
(1) Use the inspection light, magnifying glass and inspection mirror and inspect the 
rear spar lower girder area for signs of corrosion.  
C. Corrective actions only applicable in case corrosion is found. 
(1) Remove any corrosion from the vertical flange of the rear spar lower girder and 
lower area of the web. Use:  
- AR Scotchbrite Type A Very Fine (Fk05-007)

### Page 11

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 10 of 23  
 
(2) In case corrosion has been removed measure the remaining thickness at the 
damage spots in the rear spar lower girder using NDT ultrasonic equipment, refer 
to the NDT Manual Part 1 chapter 51-00-04 paragraph 12. 
(3) Make a note of the locations, size and depths of the damage spots and make 
overview photos and detail photos. 
(4) In case the damage spots have a remaining thickness more than specified in 
table 1, repair the surface treatment according step (D).  
 
Table 1 
 
 
WSTA Minimum remaining 
thickness 
Original thickness 
 (mm) (mm) 
9270 - 11794 1.9  3.56 
(5) If the damage spots have a remaining thickness less than specified in table 1, 
contact Fokker Services for evaluation of the remaining thickness. The limits of 
table 1 are not the absolute minimums, smaller remaining thickness (deeper blend 
outs) may be allowable, but need to be evaluated on a case by case basis. 
Alternatively do a repair in accordance with SBF100-57-050 or a customized repair 
advice (local repair angles) from Fokker Services B.V. 
D. Restore the surface protection in case paint, sealant and/or corrosion was removed.  
NOTE:  Restoration of surface coating may be postponed for 500 flight hours in case 
only paint top coat was removed. In case primer was removed or corrosion 
was found, restoration of the coating may not be postponed. 
(1) In case primer was removed, apply alodine and a new coat of primer. Refer to the 
AMM chapter 51-21-00. Use: 
- AR cleaning solvent Methyl Ethyl Ketone (or 
equivalent) 
(Fk11-003) 
- AR lint-free cloth - (Fk05-044) 
- AR conversion coating Alodine 1201 or  (Fk13-003D)
   Alodine 1132 Touch-n-Prep (Fk13-003E) 
- AR primer Aerodur Primer S15/60 (Fk07-008) 
(2) In case sealant was damaged and/or removed, apply new sealant with skydrol 
resistant coating on top of the lower girder and between the lower girder and the 
skin rebate. Refer to figure 5 and the SRM chapter 51-23-01. Use: 
- AR cleaning solvent Methyl Ethyl Ketone (or 
equivalent) 
(Fk11-003) 
- AR lint-free cloth - (Fk05-044) 
- AR sealant PS870B (Fk09-017A) 
- AR skydrol-resistant coating Nycote 88 (Fk09-008)

### Page 12

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 11 of 23  
 
(3) In case paint was removed, apply a new paint coat. Refer to the AMM chapter 
51-21-00. Use: 
- AR cleaning solvent Methyl Ethyl Ketone (or 
equivalent) 
(Fk11-003) 
- AR lint-free cloth - (Fk05-044) 
- AR paint Aerodur Finish C21/100 (Fk07-027) 
E. Modification of the trailing edge rebates for installation of the skin panels as removable 
access panels. 
Refer to figures 1 and 2. 
(1) At the eight (8) rivet positions (indicated as green dots) countersink the holes on 
the lower side of the structure and install rivets in the reworked holes. Use:  
- 8 solid rivets MS20426AD5  
(2) Increase the diameter of the indicated bolt holes in the structure to a diameter of 
4,9 mm H13. 
(3) On the four (4) indicated positions install anchor nuts directly on the structure. Use: 
- 8 solid rivets NAS1097AD3  
- 4 anchor nuts MS21075L3E  
- AR sealant PS870A (Fk09-016A) 
(4) Create anchor nuts plates. 
(a) Make plates to fit on the indicated positions.  
Use at the rear spar and on the rib flanges: 
- AR Alclad sheet 2024T3 thickness 0,8 mm;  
Use in the pockets of the balance plate support beams: 
- 13.5 tapered plates pn D15003-701;  
NOTES: -  Cut the sheet and tapered plates to size. 
-  The balance plate support beams have 16 pockets (per wing) in 
 which an anchor nut plate need to be placed. For 11 pockets a 
 complete tapered plate pn D15003-701 is used and cut to size; for 
 5 pockets the half of a tapered plate pn D15003-701 is used and 
 cut to size. This results in 13.5 tapered plates necessary per wing. 
-  Tapered plate D15003-701 can also be made locally using material 
 2024T3 Alclad sheet, 170×25×2,5 mm. For the cross-section refer 
 to figure 7. 
(b) Copy drill the bolt hole positions from the structure into the plates and tapered 
plates. After copy drilling enlarge the diameter to 5,3 mm H13.  
(c) Position the anchor nuts as indicated in the figures on the plates and tapered 
plates, mark the rivets holes and drill the rivets holes for installation of 
NAS1097AD3 rivets.

### Page 13

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 12 of 23  
 
(d) Apply surface protection to the fabricated plates. Use:  
- AR conversion coating Alodine 1201 or  (Fk13-003D) 
   Alodine 1132 Touch-n-Prep (Fk13-003E) 
- AR primer Aerodur Primer S15/60 (Fk07-008) 
(e) Install the anchor nuts on the plates as indicated. Use: 
- AR sealant PS870A (Fk09-016A) 
- 290 solid rivets NAS1097AD3  
- 112 anchor nuts MS21075L3E  
- 33 anchor nuts MS21073L3  
(5) Install the anchor nut strips with sealant. Position them temporarily with bolts to 
ensure proper position. Use: 
- AR sealant PS870A (Fk09-016A) 
F. Modification of the composite skin panels. 
(1) On each skin panel fill four (4) fastener holes (indicated with green dots) with resin 
flush with both surfaces. Use:  
- AR laminating resin  EA9396 (TH5.558/9) 
(2) For the remaining fastener holes increase the hole diameter to 4,9 mm H13 and 
increase the countersinking to an outer diameter of 9.55 - 9.78 mm. 
NOTE: To rework the attachment holes in aramid fibers a special drilling and 
countersink procedure has to be used, to prevent damage to the fibers 
during drilling/countersinking. For this procedure refer to  
SRM 51-22-03 (Drilling, reaming and machining of composite parts) 
and/or SPM TH6.5218 (Machining of Aramid Fiber Reinforced Plastics). 
The details are as follows: 
-  Use a high spiral drill at 5200 RPM with a pressure foot to control fiber 
 breakout. If these are unavailable use a back-up clamp at the hole 
 location to prevent fiber breakout.  
-  Use a 2-blade carbide insert cutter at 500-600 rpm for countersinking. 
(3) Identify the reworked skin panels as follows using a suitable marking method: 
  
WSTA 9270-10550: 
- LH wing skin panel D15011-005 becomes D15011-701 
- RH wing skin panel D15011-006 becomes D15011-702 
  
WSTA 10550-11794: 
- LH wing skin panel D15012-001 becomes D15012-701  
- RH wing skin panel D15012-002 becomes D15012-702 
G. Completion of the work. 
(1) Remove all tools, materials and equipment from the work area. Make sure that the 
area is clean.

### Page 14

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 13 of 23  
 
Refer to figures 3 and 4. 
(2) Install the two skin panels modified in step F.  
NOTE:  The skin panel between WSTA 9270 and 10550 has access panel number 
536HB (RH: 636HB). 
The skin panel between WSTA 10550 and 11794 has access panel 
number 536JB (RH: 636JB). 
(a) Install the skin panels and bolts with interfaying sealant. For application of 
form-in-place gasket refer to the AMM, task 20-32-00-910-832-A step A. Use:  
- AR sealant PS870A (Fk09-016A) 
- AR release agent Hobilon 50 (Fk05-049) 
- 2 bolts F0N2-1611V03-03  
- 3 bolts F0N2-1611V03-04  
- 133 bolts F0N2-1611V03-05  
- 11 bolts F0N2-1611V03-06  
(3) Install access panel 536(636)GB. For application of form-in-place gasket refer to 
the AMM, task 20-32-00-910-832-A step A. Use: 
- AR sealant PS870A (Fk09-016A) 
- AR release agent Hobilon 50 (Fk05-049) 
(4) Fill the gaps at all panels to create flush surface. Use: 
- AR sealant PS870B (Fk09-017A) 
(5) Restore the surface coating of the skins in the work area. Use: 
- AR primer Aerodur Primer S15/60 (Fk07-008) 
- AR paint Aerodur Finish C21/100 (Fk07-027) 
H. Report your findings to Fokker Services B.V. with the following details: 
 
- Surface coating damage:  YES and restored 
 YES and Corrosion found 
 NO, nil findings 
- Corrosion:  YES, within limits  
 YES, beyond SB limits  
 NO 
- In case corrosion beyond SB limits and evaluation for ‘stay as is’ approval is 
requested:  
report locations, size, remaining thickness and photos (overview & detail photos) 
NOTE:  Every inspection result shall be reported to Fokker Services B.V. even if there 
are nil findings.

### Page 15

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 14 of 23  
 
Part 2: The One-Time Inspection of the LH and RH Wing Rear Spar Lower Girder Area 
from WSTA 2635 to 8700 and 11794 to 12975.  
A. Get access and prepare the inspection area. 
(1) Open access panels 532JB, 532KB, 532LB, 532MB, 532NB, 532PB, 532QB, 
534CB, 534DB, 534EB, 534FB, 536BB, 536CB, 536DB, 536EB and 536FB  
(For RH wing the leading ‘5’ of the panel numbers is changed into ‘6’). 
(2) Remove any blistered, cracked, flaking or loose paint and/or sealant from the 
vertical flange of the rear spar lower girder and lower area of the web. Use a non-
metal brush, non metal scraper, compressed air or any suitable means. 
B. Inspect the Rear Spar Lower Girder Area from WSTA 2635 to 8700 and 11794 to 
12975. 
(1) Use the inspection light, magnifying glass and inspection mirror and inspect the 
rear spar lower girder for signs of corrosion.  
C. Corrective actions only applicable in case corrosion is found. 
(1) Remove any corrosion from the vertical flange of the rear spar lower girder and 
lower area of the web. Use:  
- AR Scotchbrite Type A Very Fine (Fk05-007)  
(2) In case corrosion has been removed measure the remaining thickness at the 
damage spots in the rear spar lower girder using NDT ultrasonic equipment, refer 
to the NDT Manual Part 1 chapter 51-00-04 paragraph 12. 
(3) Make a note of the locations, size and depths of the damage spots and make 
overview photos and detail photos. 
(4) In case the damage spots have a remaining thickness more than specified in 
table 2, repair the surface treatment according step (D).

### Page 16

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 15 of 23  
 
Table 2 
 
 
WSTA Minimum remaining 
thickness 
Original thickness 
 (mm) (mm) 
2785 - 5280 2.8  5.0 
5280 - 5860 1.6 5.0 
5860 - 8200 1.6  3.56 
8200 - 9270* 1.9  3.56 
11794 - 12975 1.9  2.54 
NOTE *:  If SF100-57-049 and ALS 572009-00-13 are accomplished 
simultaneous, the limits as given in Table 2 overrule the limits as given in 
the SRM, chapter 57-20-02, Repair No. 6, dated DEC 01/14, for the area 
between WSTA 8700 and WS 9270. 
(5) If the damage spots have a remaining thickness less than specified in table 2, 
contact Fokker Services for evaluation of the remaining thickness. The limits of 
table 2 are not the absolute minimums, smaller remaining thickness (deeper blend 
outs) may be allowable, but need to be evaluated on a case by case basis. 
Alternatively do a repair in accordance with SBF100-57-050 (only applicable for 
the area outboard WSTA 8200) or a customized repair advice (local repair angles) 
from Fokker Services B.V. 
D. Restore the surface protection in case paint, sealant and/or corrosion was removed.  
NOTE:  Restoration of surface coating may be postponed for 500 flight hours in case 
only paint top coat was removed. In case primer was removed or corrosion 
was found, restoration of the coating may not be postponed. 
(1) In case primer was removed, apply alodine and a new coat of primer. Refer to the 
AMM chapter 51-21-00. Use: 
- AR cleaning solvent Methyl Ethyl Ketone (or 
equivalent) 
(Fk11-003) 
- AR lint-free cloth - (Fk05-044) 
- AR conversion coating Alodine 1201 or  (Fk13-003D)
   Alodine 1132 Touch-n-Prep (Fk13-003E) 
- AR primer Aerodur Primer S15/60 (Fk07-008) 
(2) In case sealant was damaged and/or removed, apply new sealant with skydrol 
resistant coating on top of the lower girder and between the lower girder and the 
skin rebate. Refer to figure 5 and the SRM chapter 51-23-01. Use: 
- AR cleaning solvent Methyl Ethyl Ketone (or 
equivalent) 
(Fk11-003) 
- AR lint-free cloth - (Fk05-044) 
- AR sealant PS870B (Fk09-017A) 
- AR skydrol-resistant coating Nycote 88 (Fk09-008)

### Page 17

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 16 of 23  
 
(3) In case paint was removed, apply a new paint coat. Refer to the AMM chapter 51-
21-00. Use: 
- AR cleaning solvent Methyl Ethyl Ketone (or 
equivalent) 
(Fk11-003) 
- AR lint-free cloth - (Fk05-044) 
- AR paint Aerodur Finish C21/100 (Fk07-027) 
E. Completion of the work. 
(1) Remove all tools, materials and equipment from the work area. Make sure that the 
area is clean. 
(2) Close all access panels. For access panels installed with sealant refer to the 
application of form-in-place gasket in the AMM, task 20-32-00-910-832-A step A. 
Use: 
- AR sealant PS870A (Fk09-016A) 
- AR release agent Hobilon 50 (Fk05-049) 
F. Report your findings to Fokker Services B.V. with the following details: 
 
- Surface coating damage:  YES and restored 
 YES and Corrosion found 
 NO, nil findings 
- Corrosion:  YES, within limits  
 YES, beyond SB limits  
 NO 
- In case corrosion beyond SB limits and evaluation for ‘stay as is’ approval is 
requested:  
report locations, size, remaining thickness and photos (overview & detail photos) 
NOTE:  Every inspection result shall be reported to Fokker Services B.V. even if there 
are nil findings.

### Page 18

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. Reproduction or disclosure to third parti es of this document or any part thereof, or the use of any 
information contained therein for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except wi th the prior written permission of Fokker Services B.V. 
 Page 17 of 23  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
View B, see figure 2 
View A 
Figure 1 - Anchor nut strips and plugged holes - WSTA 9270-10550 
VIEW A 
View looking up 
at lower skin 
Legend: 
 Anchor nut MS21075 
 Anchor nut MS21073 
  Solid rivet MS20426AD5 
 Strip (of Alclad 2024T3 t=0.8 mm) 
 Tapered shim (of D15003-701) 
Anchor nut directly 
installed on structure 
(not on strip) 
z 
See figure 6 
        z

### Page 19

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. Reproduction or disclosure to third parti es of this document or any part thereof, or the use of any 
information contained therein for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except wi th the prior written permission of Fokker Services B.V. 
 Page 18 of 23  
 
 
 
 
 
 
 
  
VIEW B 
View looking up 
at lower skin 
Legend: 
 Anchor nut MS21075 
 Anchor nut MS21073  
  Solid rivet MS20426AD5 
 Strip (of Alclad 2024T3 t=0.8 mm) 
 Tapered shim  
 (of D15003-701) 
Figure 2 - Anchor nut strips and plugged holes - WSTA 10550-11794 
Anchor nut directly 
installed on structure 
(not on strip) 
z 
See figure 6 
        z

### Page 20

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. Reproduction or disclosure to third parti es of this document or any part thereof, or the use of any 
information contained therein for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except wi th the prior written permission of Fokker Services B.V. 
 Page 19 of 23  
 
 
 
 
 
 
 
  
View D, see figure 4 
View C 
VIEW C 
View looking up 
at lower skin 
Figure 3 - Position of bolts - WSTA 9270-10550 
a 
a 
a 
b 
b 
a a a c 
Legend: 
a: F0N2-1611V03-05 
b: F0N2-1611V03-06 
c: F0N2-1611V03-03

### Page 21

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. Reproduction or disclosure to third parti es of this document or any part thereof, or the use of any 
information contained therein for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except wi th the prior written permission of Fokker Services B.V. 
 Page 20 of 23  
 
 
 
 
  
VIEW D 
View looking up 
at lower skin 
Figure 4 - Position of bolts - WSTA 10550-11794 
a 
a 
a 
b 
b 
a a a c 
Legend: 
a: F0N2-1611V03-05 
b: F0N2-1611V03-06 
c: F0N2-1611V03-03 
d: F0N2-1611V03-04 
a 
d

### Page 22

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. Reproduction or disclosure to third parti es of this document or any part thereof, or the use of any 
information contained therein for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except wi th the prior written permission of Fokker Services B.V. 
 Page 21 of 23  
 
 
   
 
Remarks: 
46 Use fillet PS870B (Fk09-017A or equivalent). 
50 Apply 2 coats of Nycote 88 (Fk09-008) according SPM TH 6.6556. 
 
 
 
  
REBATE PLATE
12975
Figure 5 - Sealing of the lower girder Figure 6 - Cross section Z-Z 
Balance plate 
support beam 
DOF 
DOF 
Tapered 
anchor nut 
plate 
LOWER 
GIRDER

### Page 23

Service Bulletin 
Fokker Services B.V. 
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. Reproduction or disclosure to third parti es of this document or any part thereof, or the use of any 
information contained therein for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except wi th the prior written permission of Fokker Services B.V. 
 Page 22 of 23  
 
 
 
 2.0 ±0.5 mm 
21.5 ± 0.5 mm 
R = 2.25 ±0.5 mm 
92.5° ±0.5° 
Figure 7 - Cross section tapered anchor nut plate

### Page 24

Service Bulletin Quality Reporting Form 
Fokker Services B.V. 
  
Status:  
Released 
Revision:  
-  
Released date: (Mmm dd/yy) 
Mar 24/15 
Security class:  
RESTRICTED 
F100/70 Generic SB no.: 
SBF100-57-049 
Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement. 
Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except 
with the prior written permission of Fokker Services B.V. 
 Page 23 of 23  
 
SB Title: The One-Time Inspection of the LH and RH Wing Rear Spar Lower Girder from WSTA 2635 
to 8700 and 9270 to 12975 and Modification of the Wing Trailing Edge Lower Skin Panels into 
Access Panels. 
 
Use this Service Bulletin Quality Reporting Form to tell us your perception of the quality of the Service 
Bulletin. The reported data that you provide to us will be used to analyze areas of difficulties and to take 
corrective actions to further improve the quality of our Service Bulletins. We thank you for the time you 
have taken in completing this form. 
 
* Rate the scale of 1 to 4, with 1 the lowest score and 4 the highest score. 
Chapters * 1 2 3 4 
a)  Quality rating of this SB (overall) □ □ □ □ 
b)  Quality rating of the Planning Information □ □ □ □ 
c)  Quality rating of the Material Information □ □ □ □ 
d)  Quality rating of the Accomplishment Instructions □ □ □ □ 
e)  Quality rating of the Test Instructions (if applicable) □ □ □ □ 
f)  Quality rating of the Illust rations or Drawings (if applicable) □ □ □ □ 
g)  Timely delivery of the SB □ □ □ □ 
 
If you have had difficulties with one of the chapters of this Service Bulletin and/or one of your rating(s) is 
lower than 3, please give a short description of the issue. 
 
Comments: 
 
 
 
 
 
 
 
 
 
 
 
 
 
Operator: Date:  
 
Name / Title:  
 
 
Please return this form to: Fokker Services B.V. 
Engineering, Quality Department 
P.O. Box 1357 
2130 EL Hoofddorp 
The Netherlands 
Fax: +31 (0) 88 6280111 or  E-mail: technicalservices@fokker.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
