# Garmin Service Bulletin 2134: Revision A

- Rights: © Garmin. Filed by the FAA in regulations.gov docket FAA-2021-0715; AD 2022-03-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Garmin Service Bulletin 2134](https://openairdocs.org/service-documents/garmin/sb-2134.md)
- Title as filed: Garmin Mandatory STC SB 2134 Rev A
- Pages: 7
- PDF: https://openairdocs.org/files/sha256/cb/cc/cbcc394427667fcd21ae27a186512c3fbe939797af53b79b2f5a3d4cbd782bfa
- Page: https://openairdocs.org/service-documents/garmin/sb-2134/file/cbcc39442766

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

1200 E. 151st Street
Olathe, KS 66062
913-397-8200
© 2021
Garmin Ltd. or its subsidiaries
All Rights Reserved
Except as expressly provided herein, no part of this document may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage 
medium, for any purpose without the express prior written consent of Garmin.  Garmin hereby grants permission to download a single copy of this 
document and of any revision to this document onto a hard drive or other electronic storage medium to be viewed and to print one copy of this document 
or of any revision hereto, provided that such electronic or printed copy of this document or revision must contain the complete text of this copyright notice 
and provided further that any unauthorized commercial distribution of this document or any revision hereto is strictly prohibited.
STC Service Bulletin 2134 Page 1-7
April 23, 2021 Revision A
**MANDATORY**
STC SERVICE BULLETIN
NO.: 2134 Rev A
TO: Garmin Aviation Service Centers
DATE: April 23, 2021
SUBJECT: Modification of GEA 24 Resistive Fuel Probe Interface
CERTIFICATION
AUTHORIZATION: FAA STC SA01899WI MDL Revision 10 (see Approval section for details)
______________________________________________
PRODUCTS AFFECTED
All aircraft modified with G3X Touch AML STC SA01899WI, MDL Revision 9 or earlier, with an interface to 
resistive fuel quantity probes are affected.
Aircraft that are not affected: 
• Aircraft modified in accordance with G3X Touch STC SA01899WI, MDL Revision 10 or later
• Aircraft without fuel quantity gauges displayed on the G3X Touch
• Aircraft without a resistive probe interface (e.g. all CiES probes or Signal Conditioners)
If the MDL revision used for the installation and the type of fuel quantity probes are unknown, do the 
following:
1. Inspect the aircraft maintenance records for a Garmin Service Bulletin 2134 compliance 
statement.
a) If the maintenance record includes a compliance statement, no further action is required.
b) If the maintenance record is not available or does not have a compliance statement, 
proceed to step 2.

### Page 2

STC Service Bulletin 2134 Page 2-7
April 23, 2021 Revision A
2. Inspect the wire harness for the GEA 24 P244 connector to determine if resistors are installed (see 
Figure 1).
Figure 1 GEA 24 Connector P244
a) If resistors are not installed, the aircraft is not affected by this Service Bulletin. No further 
action is necessary.
b) If resistors are installed, or if the harness cannot be adequately inspected for resistors, the 
aircraft may be affected by this Service Bulletin. Proceed to Step 3. 
3. Inspect the fuel quantity sensor configuration. 
a) Press and hold the MENU key on the GDU while applying power to enter Configuration 
Mode.
b) Select ‘Engine & Airframe’.
c) Scroll down to Fuel 1 through 4.
d) If the fuel quantity sensors are configured as "Voltage" or "Frequency", the aircraft is not 
affected by this Service Bulletin. No further action is necessary.
e) If the fuel quantity sensors are configured as “Resistive” sensor (see Figure 2), the aircraft is 
affected by this Service Bulletin. See the MODIFICATION INSTRUCTIONS.
Figure 2 Evidence of Resistive Probe Interface

### Page 3

STC Service Bulletin 2134 Page 3-7
April 23, 2021 Revision A
PURPOSE
NOTE
This Service Bulletin supersedes Garmin Service Bulletin 20138. 
The G3X Touch fuel quantity gauges may provide erroneous indications when (1) interfaced to resistive 
fuel probes and (2) the GEA 24 is subject to significantly hotter or colder temperatures than the 
temperature at which the fuel gauges were calibrated during installation. 
This fixes the issue described in Garmin Service Alert 20137.
DESCRIPTION
This Service Bulletin provides instructions to modify the resistive fuel probe interface.
If the aircraft is affected, follow the MODIFICATION INSTRUCTIONS to replace the resistors in the 
harness, change the sensor configuration, and recalibrate the fuel quantity gauge.

### Page 4

STC Service Bulletin 2134 Page 4-7
April 23, 2021 Revision A
COMPLIANCE
Mandatory: This STC Service Bulletin must be incorporated within the next 100 hours time-in-service 
(TIS) after April 23, 2021 or within 12 calendar months after April 23, 2021, whichever occurs first.
APPROVAL
This Service Bulletin is FAA-approved in accordance with STC SA01899WI. Refer to the Master Drawing 
List, 005-01320-00 Rev. 10 or later FAA approved revision. 
DOCUMENTATION CONSIDERATIONS
Existing Aircraft Flight Manual Supplements and Pilot Guides are retained for this installation. No new 
documents are provided with this Service Bulletin.
All documents described in this bulletin are available at no cost in the Dealer Resource Center on the 
Garmin website https://dealers.garmin.com.
REFERENCES
All documents described in this bulletin are available at no cost in the Dealer Resource Center on the 
Garmin website https://dealers.garmin.com.
MANPOWER
Eight (8) hours labor per affected aircraft to update the interface and recalibrate resistive fuel probes. 
Table 1.  Referenced Documents
Document Title Part Number Revision(or later)
Master Drawing List Garmin G3X Touch Electronic Flight 
Instrument System Part 23 AML STC 005-01320-00 10
Garmin G3X Touch Electronic Flight Instrument System Part 
23 AML STC Installation Manual 190-02472-01 9

### Page 5

STC Service Bulletin 2134 Page 5-7
April 23, 2021 Revision A
WARRANTY INFORMATION
For installations that require the replacement of resistors and fuel tank calibration, this modification is 
warranty reimbursable for the manpower listed above.
Warranty reimbursement deadline is April 23, 2022. For proper reimbursement, when completing the 
Garmin warranty claim include the:
• aircraft registration number
• airframe serial number
• GEA 24 serial number
• copy of logbook entry showing:
◦ date
◦ airframe time
◦ compliance with Garmin Service Bulletin 2134
NOTE
Installations completed after May 3, 2021 are not eligible for warranty reimbursement.

### Page 6

STC Service Bulletin 2134 Page 6-7
April 23, 2021 Revision A
MODIFICATION INSTRUCTIONS
Perform the following for any aircraft affected by this Service Bulletin:
1. Remove all electric power.
2. Disconnect the P244 connector from the GEA 24.
3. Remove the connector backshell and cable clamp.
4. Identify the resistive fuel quantity interfaces which have a 1K ohm resistor installed in the 
harness. To assist with reassembly, note the probe wire number and tank. 
NOTE
There are four possible interfaces (FUEL QTY 1, 2, 3, and 4 on P244 pins 6, 9, 12, and 15 
respectively).
5. Remove the applicable connector pins.
6. Remove the resistor(s) from the harness.
7. Install a pair of 2.2K ohm resistors into the harness for each fuel quantity interface in accordance 
with the G3X AML STC Installation Manual (190-02472-01 Rev 9 or later) section B.30.
NOTE
Specifications and acceptable part numbers for the 2.2K ohm resistors are identified in 
section 3.1.2 of the IM.    
8. Assemble the connector backshell and cable clamp.
9. Install cable ties for strain relief in accordance with IM section B.34. 
10. Install the P244 connector on the GEA 24.
11. Connect appropriate sustainable source of power and apply power.
12. Press and hold the MENU key on the GDU while applying power to enter Configuration Mode.
13. Select ‘Engine & Airframe’.
14. Scroll down the list of sensors on the GEA 24 Inputs tab and identify the fuel quantity interfaces 
labeled Fuel 1 through 4.
15. Change the configuration from ‘Resistive’ to ‘Voltage’ for each resistive fuel quantity interface in 
accordance with IM section 5.33.1.9 and Table C-6.
16. Perform the fuel quantity calibration procedure for each interface in accordance with IM section 
5.33.1.9.1.
17. Complete the post installation check out procedure in accordance with IM section 6.15.8.
18. Remove the placard installed on the instrument panel by SB 20138, if applicable.
19. Make the following entry in the aircraft maintenance record (airframe logbook):
The G3X Touch EFIS installation in this aircraft complies with Garmin Service Bulletin SB 2134 
Rev A.

### Page 7

STC Service Bulletin 2134 Page 7-7
April 23, 2021 Revision A
MATERIAL INFORMATION
Garmin will provide the new resistors upon request, contact Aviation Product Support and order 
p/n 011-05829-00 (Sub-Assy, Resistor Kit, 2.2K Ohm).
NOTE
This kit contains quantity (4) resistors p/n RN60D2201FB14 which is enough to modify 
two fuel quantity interfaces.  If the aircraft has more than two resistive fuel quantity 
interfaces (i.e main tanks plus aux tanks), order a second kit.   
The STC documentation is downloadable from the Dealer Resource Center 
https://dealers.garmin.com.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
