# General Electric Service Bulletin CF34-8C 72-0356: No revision named

- Rights: © General Electric Company. Filed by the FAA in regulations.gov docket FAA-2022-0400; AD 2022-08-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [General Electric Service Bulletin CF34-8C 72-0356](https://openairdocs.org/service-documents/ge/cf34-8c-72-0356.md)
- Title as filed: CF34-8C SB 72-0356-R00_15Feb2022_Publish
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/c4/8c/c48cd16f5d7d564f2a91530059380c7bc614e2230ab9a42283978e3740dd3dbb
- Page: https://openairdocs.org/service-documents/ge/cf34-8c-72-0356/file/c48cd16f5d7d

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

CF34-8C Service Bulletins (SBs)
SB 72-0356 R00 ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check
One-Time Inspection
Date Printed:
2022/02/15
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
reproduced without the express written consent of GE. Technical data is
considered ITAR and/or EAR controlled; transfer of this data to a Non-US
Person, without USG authorization, is strictly prohibited.
Page
1 of 6
CF34-8C SERVICE BULLETIN - 72-0356 R00 Revised:02/15/2022
SB 72-0356 R00 ENGINE - COMPRESSOR STATOR ASSEMBLY (72-32-00) - ACTUATING
LINKAGE ASSEMBLY TORQUE CHECK ONE-TIME INSPECTION
Issued:
02/15/2022
GE Designated: -CONFIDENTIAL-
The information contained in this document is GE proprietary information and is
disclosed in confidence. It is the property of GE and shall not be used, disclosed to
others or reproduced without the express written consent of GE, including, but without
limitation, it is not to be used in the creation, manufacture, development, or
derivation of any repairs, modifications, spare parts, designs, or configuration
changes or to obtain FAA or any other government or regulatory approval to do so. If
consent is given for reproduction in whole or in part, this notice and the notice set
forth on each page of this document shall appear in any such reproduction in whole or
part.
This technical data is considered subject to the Export Administration Regulations
(EAR) pursuant to 15 CFR Parts 730-774. Transfer of this data by any means to a
Non-U.S. Person, whether in the United States or abroad, without the proper U.S.
Government authorization (e.g., License, exemption, NLR, etc.), is strictly
prohibited.
Copyright (2022) General Electric Company, U.S.A.
1. PLANNING INFORMATION
A. Effectivity
* * * CF34-8C1/-8C5/-8C5B1
This Service Bulletin is applicable to all CF34-8C engines that have
accumulated a total of 250 or more parked days outdoors (if installed on an
aircraft) or stored days outdoors (if uninstalled), or any combination thereof,
in the last 24 months (from the issued date of this Service Bulletin).
NOTE:The total number of parked or stored days in the last 24 months is accumulated over time and
does not have to be consecutive. For example, within the last 24 months of issued date of this
bulletin, if an engine installed on an aircraft was parked outdoors for 150 days, then
operated for one flight, and subsequently was parked outdoors for another 100 days before
returning to service, this engine would be applicable to this Service Bulletin.
NOTE:For engines not in service that are accumulating parked or stored days but have not reached
the 250-day threshold at the date of this Service Bulletin release, perform this bulletin if
the engine reaches the 250-day threshold before returning to service.
NOTE:Parking day is counted as 24 consecutive hours without engine operation.
NOTE:If the suspect engines have been previously inspected on-wing for freedom of movement on the
actuating linkage assembly according to GE recommendations within the last 4 months of the
issued date of this Service Bulletin, this Service Bulletin is not applicable.
NOTE:If the suspect engines have already been to a shop/repair facility or have had compressor
cases routed to a shop/repair facility after having been through prolonged parking and the
compressor case bore holes and the compressor inlet guide vane (IGV) outer shroud bushing and
vane spindle bushing, were confirmed no-corrosion, the actuating linkage assembly has freedom
of movement and this Service Bulletin is not applicable.
NOTE:A non-environmentally controlled facility is also applicable wherever the term "outdoors" is
used.
The actuating system linkage assemblies (actuating linkage assemblies) P/N 
, P/N , P/N , P/N , and P/N 4128T48G03 4128T48G05 4128T48G07 4128T48G08 4128T48G09
and compressor actuating linkage assemblies (actuating linkage assemblies) P/N 
, P/N , and P/N  are affected by this Service4129T92G01 4129T92G02 4129T92G03
Bulletin.
B. Description
This Service Bulletin provides instructions to do a one-time inspection of the
affected actuating linkage assembly aimed to identify possible interface
corrosion/seizure on the compressor case, compressor IGV outer shroud bushing,
vane spindle bushing, compressor stator IGV variable vane, compressor stator

### Page 2

CF34-8C Service Bulletins (SBs)
SB 72-0356 R00 ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check
One-Time Inspection
Date Printed:
2022/02/15
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
reproduced without the express written consent of GE. Technical data is
considered ITAR and/or EAR controlled; transfer of this data to a Non-US
Person, without USG authorization, is strictly prohibited.
Page
2 of 6
stage 1 variable vane, compressor stator stage 2 variable vane, compressor
stator stage 3 variable vane, and compressor stator stage 4 variable vane.
C. Compliance
NOTE:All full authority digital engine control (FADEC) CF34-8C engines with FADEC software version
6.50 and below will have inspection condition Category 1, Impact A.
NOTE:All FADEC CF34-8C engines with FADEC software version 6.60 and above will have inspection
condition Category 2, Impact B.
Category 1
GE recommends that you do this Service Bulletin as soon as possible without
effect on revenue service but before the date of this Service Bulletin:
(1) For engines already in service, do as follows:
(a) If the parking or storage location was less than or equal to a 10-mile (16 km) distance
from a saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within
the next 30 flight hours or within 5 calendar days of flight operation from the
issued date of this Service Bulletin, whichever comes first.
*On the sister engine, do an inspection of the actuating linkage assembly within the
next 440 engine flight hours.
(b) If the parking or storage location was more than 10 miles (16 km) and less than or
equal to a 50-mile (80 km) distance from a saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within
the next 200 flight hours or within 35 calendar days of flight operation from the
issued date of this Service Bulletin, whichever comes first.
*On the sister engine, do an inspection of the actuating linkage assembly within the
next 880 engine flight hours.
(c) If the parking or storage location was more than a 50-mile (80 km) distance from a
saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within
the next 880 flight hours.
*On the sister engine, do an inspection of the actuating linkage assembly within the
next 1,680 engine flight hours.
(2) For engines not in service, do as follows:
(a) Do an inspection of the actuating linkage assembly before returning to service.
Impact A
This recommendation is to address a condition that may affect Flight Safety.
Category 2
GE recommends that you do this Service Bulletin as soon as possible without
effect on revenue service but before the date of this Service Bulletin:
(1) For engines already in service, do as follows:
(a) If the parking or storage location was less than or equal to a 10-mile (16 km) distance
from a saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within
the next 200 flight hours or within 35 calendar days of flight operation from the
issued date of this Service Bulletin, whichever comes first.
*On the sister engine, do an inspection of the actuating linkage assembly within the
next 880 engine flight hours.
(b) If the parking or storage location was more than 10 miles (16 km) and less than or
equal to a 50-mile (80 km) distance from a saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within
the next 440 flight hours.
*On the sister engine, do an inspection of the actuating linkage assembly within the
next 880 engine flight hours.
(c) If the parking or storage location was more than a 50-mile (80 km) distance from a
saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within
the next 880 flight hours.
*On the sister engine, do an inspection of the actuating linkage assembly within the
next 1,680 engine flight hours.
(2) For engines not in service, do as follows:
(a) Do an inspection of the actuating linkage assembly before returning to service.
Impact B
This recommendation is to address a condition that may result in an Increased
Rate of In-Flight Shutdowns (IFSD), Take-Off Aborts (TOA), Air Turn Backs (ATB)
or Diversions (DIV).
NOTE:This Service Bulletin can be done on wing or in shop.

### Page 3

CF34-8C Service Bulletins (SBs)
SB 72-0356 R00 ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check
One-Time Inspection
Date Printed:
2022/02/15
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
reproduced without the express written consent of GE. Technical data is
considered ITAR and/or EAR controlled; transfer of this data to a Non-US
Person, without USG authorization, is strictly prohibited.
Page
3 of 6
This Service Bulletin is offered to improve the reliability or performance of
your GE product, or to help prevent the occurrence of the event or condition
described in this Service Bulletin. If the operator elects not to participate
in the bulletin, that decision will be taken into consideration by GE in
evaluating future product performance issues that may arise in the operator's
fleet.
D. Concurrent Requirements
None.
E. Reason
(1) Objective:
To improve reliability.
(2) Condition:
The actuating linkage assembly has been found to bind or stick causing engine to operate
off-schedule triggering of VG CMD - POSITION DISAGREE fault. This can result in FADEC
command to idle in the CF34-8C engines with software version 6.50 and below. For CF34-8C
engines with FADEC software version 6.60 and above as specified in the CF34-8C S/B ,73-0045
the VG CMD - POSITION DISAGREE fault will display an ENG DEGRADED CAS message in the
cockpit. This can result in an air turn-back or diversion event and under certain worst
case conditions could result in a momentary compressor stall.
(3) Cause:
Corrosion has been found on the inside of the compressor case around the variable geometry
stator vanes bores resulting in binding, sticking, and seizure of the compressor stator IGV
variable vane, compressor stator stage 1 variable vane, compressor stator stage 2 variable
vane, compressor stator stage 3 variable vane, and compressor stator stage 4 variable vane
during engine operation.
(4) Inspection:
The actuating linkage assembly torque check will aid operators in the early detection of
excessive corrosion build-up on the inside of the compressor case and around the compressor
IGV outer shroud bushing and vane spindle bushing bores to prevent operational events.
(5) Substantiation:
Substantiation is by analysis and fleet experience.
F. Approval
The data contained in this Service Bulletin has been reviewed by the FAA or
authorized entity representing the FAA and the repair(s) and modification(s)
herein comply with the applicable Aviation Regulations and are APPROVED for
installation in the model(s) listed in this Service Bulletin.
G. Manpower
After you get access to the actuating linkage assembly, you will need
approximately 2 man-hours to do the inspection portion of this Service
Bulletin.
H. Weight and Balance
Weight and balance are not changed.
I. References (Use the latest version of these documents)
Emergency Airworthiness Directive (EAD) 2021-23-51
GEK 105091-1, CF34-8C Line Maintenance Manual (LMM)
GEK 105092, CF34-8C Illustrated Parts Catalog (IPC)
CF34-8C S/B , ENGINE FUEL AND CONTROL - FADEC (73-21-01) - Introduction73-0045
of Improved FADEC Software Version 6.60
CF34-8C S/B , AIR SYSTEM - Compressor Variable Geometry Actuator75-0028
Components (75-30-01) - Master Compressor Variable Geometry Actuator and Slave
Compressor Variable Geometry Actuator One-Time Inspection
J. Publications Affected
None.
K. Interchangeability
Not applicable.
L. Software Accomplishment Summary
Not applicable.
2. MATERIAL INFORMATION
A. Material - Price and Availability
(1) Parts necessary to do this Service Bulletin:
None.
(2) Other Spare Parts:
None.
(3) Consumables:
None.
B. Industry Support Information

### Page 4

CF34-8C Service Bulletins (SBs)
SB 72-0356 R00 ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check
One-Time Inspection
Date Printed:
2022/02/15
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
reproduced without the express written consent of GE. Technical data is
considered ITAR and/or EAR controlled; transfer of this data to a Non-US
Person, without USG authorization, is strictly prohibited.
Page
4 of 6
None.
C. Configuration Chart
None.
D. Parts Disposition
None.
E. Tooling - Price and Availability
Tool Number Description
-- Torque Wrench, 110 lb in. (12.4 Nm) torque check capability
3. ACCOMPLISHMENT INSTRUCTIONS
A. General
(1) For the actuating linkage assembly that connects to the master compressor variable geometry
actuator (SIN 30401) and slave compressor variable geometry actuator (SIN 30402), do as
follows:
(a) Disconnect the master compressor variable geometry actuator (SIN 30401) from the
compressor actuator bellcranks. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 005
and do as follows:
NOTE:It is not necessary to remove or disconnect the compressor variable geometry preset
link assemblies from the actuator shafts or from the compressor IGV actuating ring
segment, compressor stage 1 actuating ring segment, compressor stage 2 actuating ring
segment, compressor stage 3 actuating ring segment, and compressor stage 4 actuating
ring segment.
1 Do an inspection of the master compressor variable geometry actuator (SIN 30401)
rod-end for corrosion. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 005,
Subtask 75-00-00-221-023 and do as follows:
a If you find corrosion on the master compressor variable geometry actuator (SIN
30401) rod-end, report findings to GE. Refer to Figure 1.
b If you find no corrosion and the rod end ball bearing turns freely, the master
compressor variable geometry actuator (SIN 30401) rod-end is serviceable.
NOTE:If the inspection for master compressor variable geometry actuator (SIN
30401) rod-end was previously done in accordance with CF34-8C S/B  or75-0028
EAD 2021-23-51 or equivalent GE recommendation, step 3.A.(1)(a)  is not1
necessary, unless the engine was parked or stored outdoors or in a
non-environmentally controlled facility for more than 180 days after the
prior inspection was done.
(b) Disconnect the slave compressor variable geometry actuator (SIN 30402) from the
compressor actuator bellcranks. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 006
and do as follows:
NOTE:It is not necessary to remove or disconnect the compressor variable geometry preset
link assemblies from the actuator shafts or from the compressor IGV actuating ring
segment, compressor stage 1 actuating ring segment, compressor stage 2 actuating ring
segment, compressor stage 3 actuating ring segment, and compressor stage 4 actuating
ring segment.
1 Do an inspection of the slave compressor variable geometry actuator (SIN 30402)
rod-end for corrosion. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 006,
Subtask 75-00-00-221-022 and do as follows:
a If you find corrosion on the slave compressor variable geometry actuator (SIN
30402) rod-end, report findings to GE. Refer to Figure 1.
b If you find no corrosion and the rod end ball bearing turns freely, the slave
compressor variable geometry actuator (SIN 30402) rod-end is serviceable.
NOTE:If the inspection for slave compressor variable geometry actuator (SIN 30402)
rod-end was previously done in accordance with CF34-8C S/B  or EAD75-0028
2021-23-51 or equivalent GE recommendation, step 3.A.(1)(b)  is not1
necessary, unless the engine was parked or stored outdoors or in a
non-environmentally controlled facility for more than 180 days after the
prior inspection was done.
CAUTION:TORQUE CHECK MUST NOT BE DONE SIMULTANEOUSLY IN THE TWO COMPRESSOR ACTUATOR
BELLCRANKS. DAMAGE OF THE COMPRESSOR IGV ACTUATING RING SEGMENT, COMPRESSOR STAGE 1
ACTUATING RING SEGMENT, COMPRESSOR STAGE 2 ACTUATING RING SEGMENT, COMPRESSOR STAGE
3 ACTUATING RING SEGMENT, COMPRESSOR STAGE 4 ACTUATING RING SEGMENT, COMPRESSOR
STATOR IGV ACTUATING ARM, COMPRESSOR STATOR STAGE 1 THROUGH 4 VANE ACTUATION ARM,
OR COMPRESSOR STATOR SPLITLINE STAGE 1 THROUGH 4 VANE ACTUATION ARM CAN OCCUR.
(c) Install a torque wrench on the compressor actuator bellcrank forward retaining double
hexagonal head machine bolt (machine bolt) where the master compressor variable
geometry actuator (SIN 30401) is installed and do as follows:
1 Apply a rotational torque to move the actuating linkage assembly toward fully open
and toward fully closed positions. Torque cannot be more than 110 lb in. (12.4 Nm)
while you move the actuating linkage assemblies toward fully open and fully closed
positions. Refer to  and do as follows:Figure 2
a If you can move the actuating linkage assembly with a torque of 110 lb in.
(12.4 Nm) or less, no more action is necessary.
b If there is a compressor stator IGV actuation arm, compressor stator stage 1
through 4 vane actuation arm, or compressor stator splitline stage 1 through 4

### Page 5 (OCR)

CF34-8C Service Bulletins (SBS)
SB 72-0356 ROO ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check
One-Time Inspection
vane actuation arm stuck or if you cannot move the actuating linkage assembly
toward fully open and toward fully closed positions with the recommended
torque, this can be an indication of corrosion between the compressor case,
compressor IGV outer shroud bushing, vane spindle bushing, compressor stator
IGV variable vane, compressor stator stage 1 variable vane, compressor stator
stage 2 variable vane, compressor stator stage 3 variable vane, and compressor
stator stage 4 variable vane. No fly-on limits are permitted and remove the
engine to clean the compressor case bore bushing holes and replace the
compressor IGV outer shroud bushing and vane spindle bushing.
Send inspection report to GE. Refer to Figure 1.
(d) Connect the master compressor variable geometry actuator (SIN 30401) to the compressor
actuator bellcrank. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 005.
(e) Connect the slave compressor variable geometry actuator (SIN 30402) to the compressor
actuator bellcrank. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 006.
INSPECTION REPORT FOR CF34-8C S/B 72-0356
NOTE: CONTACT GE AVIATION FLEET SUPPORT IF THERE ARE ANY FINDINGS.
E-MAIL (U.S.A.): AVIATION.FLEETSUPPORT@GE.COM
E-MAIL (CHINA AND ASIA): AVIATION.FLEETSUPPORT.CN@GE.COM
AIRCRAFT TAIL NUMBER
ENGINE POSITION
ENGINE SERIAL NUMBER (ESN)
ENGINE TIME SINCE NEW (ETSN)
ENGINE TIME SINCE OVERHAUL (ETSO)
DATE
ENGINE MODEL
ENGINE HISTORY
SEND THE INFORMATION THAT FOLLOWS:  OBSERVATIONS
DO A CHECK OF THE ACTUATING LINKAGE ASSEMBLY TORQUE  PASS  FAIL
TO 110 LB IN. (12.4 NM)
DO A CHECK OF THE MASTER COMPRESSOR VARIABLE GEOMETRY ACTUATOR  PASS  FAIL  N/'A
ROD-END AND SLAVE COMPRESSOR VARIABLE GEOMETRY ACTUATOR ROD-END
FOR CORROSION
HAS THIS ENGINE BEEN FLYING FREQUENTLY IN BETWEEN COASTAL CITIES OR  YES  NO
SALINE ENVIRONMENTS?
IF YES, FOR HOW LONG? (DAYS, MONTHS, OR YEARS)
HAS THIS ENGINE BEEN RECENTLY STORED OUTDOORS IN A COASTAL LOCATION? _ YES  NO
IF YES, IN WHAT CITY WAS IT STORED?
IF YES, FOR HOW LONG? (DAYS, MONTHS, OR YEARS)
HAS THIS ENGINE BEEN INSTALLED ON A PARKED AIRCRAFT OUTDOORS IN A  YES  NO
COASTAL LOCATION?
IF YES, FOR HOW LONG? (DAYS, MONTHS, OR YEARS)
IF YES, HOW WAS THE AIRCRAFT PARKING CONDITION? (HANGAR, PARKWAY, ETC.)
IF YES, IN WHAT CITY WAS IT PARKED?
NUMBER OF ENGINE CYCLES SINCE RETURNING BACK TO NORMAL REVENUE
ENGINE OPERATION
SINCE RETURNING BACK TO NORMAL REVENUE SERVICE WHAT IS THE EXPECTED
AIRCRAFT UTILIZATION GOING FORWARD (CYCLES/MONTH)?
6033627-00
Inspection Report
Figure 1
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/02/15  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  5 of 6
Person, without USG authorization, is strictly prohibited.

### Page 6 (OCR)

CF34-8C Service Bulletins (SBs)
SB 72-0356 ROO ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check
One-Time Inspection
COMPRESSOR
ACTUATOR BELLORANK
MACHINE
BOLT
FWD
6033983-00
Actuating Linkage Assembly Torque Check Example
Figure 2
GE Designated: - CONFIDENTIAL Subject to the restrictions on the media
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/02/15  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  6 Of 6
Person, without USG authorization, is strictly prohibited.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
