# General Electric Service Bulletin 72-0306: No revision named

- Rights: © General Electric Company. Filed by the FAA in regulations.gov docket FAA-2019-0665, the docket of AD 2020-08-01. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [General Electric Service Bulletin 72-0306](https://openairdocs.org/service-documents/ge/sb-72-0306.md)
- Title as filed: SB 72-0306-R00_CF34-3
- Pages: 12
- PDF: https://openairdocs.org/files/sha256/89/f4/89f4b559182c8bb67122a2f5a8a8a0b16dc2bd7f8112d0ecf6bcd5190e878074
- Page: https://openairdocs.org/service-documents/ge/sb-72-0306/file/89f4b559182c

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
GE PROPRIETARY INFORMATION
The information contained in this document is GE proprietary information and is disclosed in con-
¿dence. It is the property of GE and shall not be used, disclosed to others or reproduced without
the express written consent of GE, including, but without limitation, it is not to be used in the cre-
ation, manufacture, development, or derivation of any repairs, modi ¿cations, spare parts, designs, or
con¿guration changes or to obtain FAA or any other government or regulatory approval to do so. If
consent is given for reproduction in whole or in part, this notice and the notice set forth on each page
of this document shall appear in any such reproduction in whole or in part.
This technical data is considered EAR controlled pursuant to 15 CFR Parts 730-774 respectively.
Transfer of this data by any means to a Non-US Person, whether in the United States or abroad,
without the proper U.S. Government authorization (e.g., License, exemption, NLR, etc.), is strictly
prohibited.
Copyright (2017) General Electric Company, U.S.A.
September 27, 2017 CF34-BJ S/B 72-0306
PAGE 1 of 12

### Page 2

ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
1. PLANNING INFORMATION
A. Effectivity
CF34-1A/-3A/-3A1/-3A2/-3B
This Service Bulletin is applicable to all CF34-BJ engines that have any fan blade
which has been repaired by ATI-UK under SEI-582, 72-21-12, REPAIR 01, REPAIR
02 or REI-13471 or SEI-782, 72-21-12 REPAIR 01, REPAIR 02, or REI-13471 with
the serial numbers listed in paragraph 4., A PPENDIX A.
These serial numbers are the best available data.
The fan blades P/N 3901T93G05, P/N 3901T93G06, P/N 4923T52P03, P/N
4923T52P05, P/N 4923T52P06, P/N 4923T52P07, P/N 4923T52P13, P/N
4923T52P14, P/N 4923T56G02, P/N 4923T56G04, P/N 4923T56G05, P/N
4923T56G06, P/N 4923T56G07, P/N 4923T56G08, P/N 4923T56G09, P/N
4923T56G10, P/N 4923T56G11, P/N 4923T56G12, P/N 4923T56G13, P/N
4923T56G14, P/N 5922T34P01, P/N 6018T30P03, P/N 6018T30P05, P/N
6018T30P06, P/N 6018T30P07, P/N 6018T30P13, P/N 6018T30P14, and P/N
6018T30P15 are affected by this Service Bulletin.
B. Description
This Service Bulletin provides instructions for the removal of speci ¿c fan blades or
¿eld modi ¿ed fan blades listed in paragraph 4., A PPENDIX A.
C. Compliance
Category 2
GE recommends that you do this Service Bulletin as soon as possible without effect
on revenue service but no later than the ¿rst overnight maintenance period after
identifying an affected fan blade. Operators may exercise a deferment as described
in paragraph 3., A CCOMPLISHMENT INSTRUCTIONS of this Service Bulletin.
Paragraph 4., A PPENDIX A lists the suspect fan blades which have been repaired
by ATI-UK under SEI-582, 72-21-12, REPAIR 01, REPAIR 02, and REI-13471 or
SEI-782, 72-21-12, REPAIR 01, REPAIR 02, and REI-13471. Operators should
complete a review of their records for this subgroup no later than 14 days from the
issuance of this Service Bulletin. Any fan blade found in a record search should
be removed from revenue service at the next overnight maintenance period or
from ready to install spares. Operator has the discretion to perform the repair per
CF34-BJ S/B 72-0123.
Impact B
This recommendation is to address a condition that may result in an increased Rate
of In-Flight Shutdowns (IFSD), T ake-Off Aborts (TOA), Air Turn Backs (ATB) or
Diversions (DIV).
NOTE: This Service Bulletin can be done on wing or in shop.
September 27, 2017 CF34-BJ S/B 72-0306
PAGE 2
GE PROPR IETARY INFORMATION - Subject to the restrictions on the cover or ¿rst page.

### Page 3

ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
This Service Bulletin is offered to improve the reliability or performance of your GE
product, or to help prevent the occurrence of the event or condition described in this
Service Bulletin. If the operator elects not to participate in the bulletin, that decision
will be taken into consideration by GE in evaluating future product performance
issues that may arise in the operator’s Àeet.
D. Concurrent Requirements
None.
E. Reason
(1) Objective:
T o remove parts from service and reduce signi ¿cant events.
(2) Condition:
A subset of fan blades in the ¿eld are suspected to have missing lance
peening after performing a hot form repair (refer to SEI-582, 72-21-12,
REPAIR 01, REPAIR 02 or REI-13471 or SEI-782, 72-21-12 REPAIR 01,
REPAIR 02, or REI-13471) at ATI-UK between 2007 and 2009.
(3) Cause:
Shot peening is used in production to improve the compressive residual stress
and mechanical properties of the fan blade tangs, including the fan blade pin
holes, by placing a compressive residual stress in the fan blade pin holes.
Fan blades can lose their compressive residual stress during the electron
beam weld repair (REPAIR 01), hot form repair (REPAIR 02) stress relief,
or REI-13471. The loss of mechanical properties is restored with the lance
peening called out in the electron beam weld and hot form repair. During
an audit, GE Aviation has identi ¿ed the fan blades listed in paragraph 4.,
APPENDIX A as suspect to have missing lance peening.
(4) Improvement:
Removal or repair of the suspect fan blades listed in paragraph 4., A PPENDIX
A will eliminate the possibility of cracking in the fan blade tangs and/or fan
blade pin holes due to missing lance peening.
(5) Substantiation:
Substantiation is by analysis and Àeet experience.
F. Approval
The data contained in this Service Bulletin has been reviewed by the FAA or
authorized entity representing the FAA and the repair(s) and modi ¿cation(s) herein
comply with the applicable Aviation Regulations and are APPROVED for installation
in the model(s) listed in this Service Bulletin.
September 27, 2017 CF34-BJ S/B 72-0306
PAGE 3
GE PROPR IETARY INFORMATION - Subject to the restrictions on the cover or ¿rst page.

### Page 4

ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
G. Manpower
After you get access to the fan blades, you will need approximately 2 man-hours for
each engine.
H. Weight and Balance
Weight and balance are not changed.
I. References (Use the latest version of these documents)
CF34 Turbofan Engine Service Record
SEI-580, CF34-BJ Maintenance Manual (MM)
SEI-581, CF34-BJ-1A_3A_3A2 Engine Illustrated Parts Catalog (IPC)
SEI-582, CF34-BJ Shop Manual (SM)
SEI-779, CF34-BJ Engine Illustrated Parts Catalog (IPC)
SEI-780, CF34-BJ Service Manual (SM)
SEI-782, CF34-BJ Heavy Maintenance Manual (HMM)
CF34-BJ S/B 72-0123, ENGINE - General (72-00-00) - Introduction of Fan Blade
Bushing Repair
Repair Engineering Instruction (REI)-13471, Airfoil Repair by Hot Reforming and by
Electron Beam Welding
NOTE: The reference documents listed below are for the engine manufacturer's
internal use only:
BPP/EPEX No.: 63014
J. Publications Affected
None.
K. Interchangeability
Not applicable.
L. Software Accomplishment Summary
Not applicable.
2. MATERIAL INFORMATION
A. Material - Price and Availability
September 27, 2017 CF34-BJ S/B 72-0306
PAGE 4
GE PROPR IETARY INFORMATION - Subject to the restrictions on the cover or ¿rst page.

### Page 5

ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
(1) Parts necessary to do this Service Bulletin:
Part Number
Qty/
Eng Part Name
Unit ($)
Price
Pkg
Qty
Lead
Time
Days
6018T30P15 (AR) Blade, Fan Quote (-) Quote
NOTE: Prices are provided for planning purposes and are subject to change.
(2) Other Spare Parts:
Part Number
Qty/
Eng Part Name
Unit ($)
Price
Pkg
Qty
Lead
Time
Days
4029T16P17 (AR) Pin, Fan Blade
Retaining
Quote (-) Quote
NOTE: Prices are provided for planning purposes and are subject to change.
(3) Consumables:
None.
B. Industry Support Information
None.
C. Con¿guration Chart
None.
D. Parts Disposition
If the operator elects not to perform a bushing repair in any of his affected fan
blades as speci ¿ed in step 3.A.(1)(b), it must be returned to GE Aviation. Submit a
Service Request (SR) case to GE Aviation Fleet Support to obtain a case number to
be used when shipping the fan blades to GE Aviation.
Fleet Support:
E-mail (USA): aviation. Àeetsupport@ge.com
E-mail (China & Asia): aviation. Àeetsupport.cn@ge.com
U.S.A. Phone: 877-432-3272
International Phone: (513) 552-3272
China & Asia Phone: +86 21 38777666
E. Tooling - Price and Availability
None.
September 27, 2017 CF34-BJ S/B 72-0306
PAGE 5
GE PROPR IETARY INFORMATION - Subject to the restrictions on the cover or ¿rst page.

### Page 6

ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
3. ACCOMPLISHMENT INSTRUCTIONS
A. General
(1) Access the fan rotor section and remove the fan blade retaining pins and fan
blades listed in paragraph 4., A PPENDIX A. Refer to SEI-580, 72-20-00,
REMOVAL/INSTALLATION or SEI-582, 72-21-00, DISASSEMBLY or SEI-780,
72-00-00, MAINTENANCE PRACTICE 36 or SEI-782, 72-00-00, SPECIAL
PROCEDURE 11 or 72-00-01, DISASSEMBLY 02 or 72-00-21, REMOVAL
or 72-21-00, DISASSEMBLY and do as follows:
NOTE: T h i ss t e pm u s tb ed o n ea tt h e ¿rst overnight maintenance interval after
you identify an affected fan blade that is in service.
(a) Return all affected fan blades to GE Aviation or continue with step
3.A.(1)(b).
OR
(b) After you remove the fan blade from service, repair the fan blade as
speci¿ed in CF34-BJ S/B 72-0123 at operator’s convenience.
NOTE: CF34-BJ S/B 72-0123 introduces a fan blade bushing repair by a
controlled cold expansion procedure, approved by GE Aviation,
that extends the permitted fan blade operation by an additional
18,000 cycles from the time of the repair.
(c) Install the new fan blades and the new fan blade retaining pins
again. Refer to SEI-580, 72-20-00, REMOVAL/INSTALLATION or
SEI-582, 72-21-00, ASSEMBLY or SEI-780, 72-00-00, MAINTENANCE
PRACTICE 36 or SEI-782, 72-00-00, SPECIAL PROCEDURES 11 or
72-00-01, ASSEMBLY 02 or 72-00-21, INSTALLATION or 72-21-00,
ASSEMBLY and do as follows:
1 Make sure that there is suf ¿cient clearance between the fan blade
and the containment case and correct it if necessary.
NOTE: It is recommended that the fan blade retaining pins P/N
4029T16P17 are installed with the new fan blades P/N
6018T30P15. It is necessary to engage the new fan blade
retaining pins in even pairs (new pin plus the pin 180
degrees away) to prevent an increase in vibration.
B. Alternative Procedure
NOTE 1: This alternative procedure is recommended only if the affected engine
is outstation or a replacement fan blade(s) is not immediately available.
(1) Do a visual and tactile inspection of the fan containment case abradable rub
strip for continuous 360-degree rub indication (Figure 1) with material removal
at the compliance requirement speci ¿ed in paragraph 1.C., C ompliance.D o
the reinspections at a maximum interval of 50 cycles or 75 hours (whichever
occurs last) and do as follows:
September 27, 2017 CF34-BJ S/B 72-0306
PAGE 6
GE PROPR IETARY INFORMATION - Subject to the restrictions on the cover or ¿rst page.

### Page 7

ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
NOTE 2: The reinspection can be done a maximum of three times after an
affected fan blade is identi ¿ed to let you procure a replacement fan
blade and/or reposition the aircraft to a maintenance base.
(a) Access the engine inlet with a direct line of sight to the fan containment
case abradable rub strip and do as follows.
1 Do a visual inspection of the abradable rub strip for a continuous
360-degree rub indication with material removal.
2 If necessary, turn the fan to see all areas. Move your ¿nger across
the abradable rub strip to do an inspection for removed material.
(b) If there is no indication or only discontinuous surface marks are present,
continue with the reinspections as speci ¿ed in step 3.B.(1) at an interval
of not more than 50 cycles or 75 hours (whichever occurs last).
NOTE: The reinspection can be done a maximum of three times after an
affected fan blade is identi ¿ed.
(c) If you ¿nd continuous indications, do step 3.B.(2). Refer to SEI-580,
72-00-00, INSPECTION or SEI-582, 72-23-00, INSPECTION or
SEI-780, 72-00-00, INSPECTION or SEI-782, 72-23-00, INSPECTION
for abradable rub strip serviceable limits. If the abradable damage
is beyond serviceable limits, repair the abradable damage within 500
additional Àight hours. Refer to SEI-580, 72-20-00, REPAIR, REPAIR-06
or SEI-582, 72-23-00, REPAIR, REPAIR-03 or SEI-782, 72-23-00,
REPAIR-03 for the red abradable rub strip or SEI-580 72-20-00, REPAIR,
REPAIR-18 or SEI-582, 72-23-11, REPAIR 19 or SEI-782, 72-23-00,
REPAIR 15 for the gray abradable rub strip. If you ¿nd punctures or
gouges in the aluminum skin under the abradable rub strip, refer to
SEI-580, 72-00-00, INSPECTION or SEI-582, 72-23-00, INSPECTION
or SEI-782, 72-23-00, INSPECTION for repair instructions.
(2) Access the fan rotor section and remove the identi ¿ed affected fan blade.
Refer to SEI-580, 72-20-00, REMOVAL/INSTALLATION or SEI-582, 72-21-00,
DISASSEMBLY or SEI-780, 72-00-00, MAINTENANCE PRACTICE 36 or
SEI-782, 72-00-00, SPECIAL PROCEDURE 11 or 72-00-01, DISASSEMBLY
02 or 72-00-21, REMOVAL or 72-21-00, DISASSEMBLY .
(3) Install the new fan blades and the new fan blade retaining pins again. Refer
to SEI-580, 72-20-00, REMOVAL/INSTALLATION or SEI-582, 72-21-00,
ASSEMBLY or SEI-780, 72-00-00, MAINTENANCE PRACTICE 36 or
SEI-782, 72-00-00, SPECIAL PROCEDURES 11 or 72-00-01, ASSEMBLY 02
or 72-00-21, INSTALLATION or 72-21-00, ASSEMBLY and do as follows:
(a) Make sure that there is suf ¿cient clearance between the fan blade and
the containment case and correct it if necessary.
NOTE: It is recommended that the fan blade retaining pins P/N 4029T16P17
are installed with the new fan blades P/N 6018T30P15. It is necessary
to engage the new fan blade retaining pins in even pairs (new pin plus
the pin 180 degrees away) to prevent an increase in vibration.
September 27, 2017 CF34-BJ S/B 72-0306
PAGE 7
GE PROPR IETARY INFORMATION - Subject to the restrictions on the cover or ¿rst page.

### Page 8

ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
C. CF34 Turbofan Engine Service Record Entry
(1) Report the fan blades found to any of the contacts that follow from GE Aviation
Fleet Support (reference CF34-BJ S/B 72-0306):
E-mail (U.S.A): Aviation. Àeetsupport@ge.com
E-mail (China & Asia): aviation. Àeetsupport.cn@ge.com
U.S.A. Phone: (513) 552-3272
International Phone: (513) 552-3272
China & Asia Phone: +86 21 38777666
(a) Include engine serial number (ESN), time since new (TSN), cycles since
new (CSN), fan blade part number(s), and fan blade serial number(s).
NOTE: GE Aviation Fleet Support will notify product support engineering
(PSE) of the ¿nds/compliance information sent in.
(2) Make an entry in the CF34 Turbofan Engine Service Record as follows:
(a) Record compliance to this Service Bulletin in the Engine Service
Record, Section II (Service Bulletins) and do as follows:
1 Include ESN, TSN, CSN, fan blade part number(s), and fan blade
serial number(s).
(b) Send a copy of the compliance entry data to:
GE Aviation
1000 Western Avenue
Lynn, MA 01910
U.S.A.
ATTN.: Lynn Product Data Center, MZ 264X7
CF34 Service Bulletin Coordinator
September 27, 2017 CF34-BJ S/B 72-0306
PAGE 8
GE PROPR IETARY INFORMATION - Subject to the restrictions on the cover or ¿rst page.

### Page 9 (OCR)

CF34 TURBOFAN (BUSINESS JET)
GE Aircraft Engines
SERVICE BULLETIN
ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
FAN BLADE
AREA TO BE
INSPECTED
5043395-00
Fan Containment Case Inspection
Figure 1, ( Sheet 1 of 2)
September 27, 2017  CF34-BJ S/B 72-0306
PAGE 9
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page.

### Page 10 (OCR)

CF34 TURBOFAN (BUSINESS JET)
GE Aircraft Engines
SERVICE BULLETIN
ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
FAN BLADE
FAN CASE
• AREA TO BE
INSPECTED
5043396-00
Fan Containment Case Inspection
Figure 1, ( Sheet 2)
September 27, 2017  CF34-BJ S/B 72-0306
PAGE 10
GE PROPRIETARY INFORMATION - Subject to the restrictions on the cover or first page.

### Page 11

ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
4. APPENDIX A
T able 1. Affected Serial Numbers of the Fan Blades
Serial
Number
Serial
Number
Serial
Number
Serial
Number
Serial
Number
Serial
Number
BA200220 KGABE426 KGACG710 KGAGB116 MAD10286 MAE42665
BA256679 KGABF382 KGACH423 KGAGB284 MAE32257 MAE43187
BA309195 KGABF383 KGACJ026 KGAGB357 MAE32373 MAE43737
BA489838 KGABF489 KGACJ113 KGAGB550 MAE32776 MAE44381
BA662584 KGABG187 KGACJ256 KGAGB556 MAE32979 MAE44382
BA663010 KGABH211 KGACJ339 KGAGC763 MAE33217 MAE44818
BA683308 KGABH423 KGACJ652 KGAGC765 MAE33381 MAE45089
BA683759 KGABJ587 KGACJ655 KGAGC822 MAE33386 MAE45127
BA698133 KGABJ865 KGACJ686 KGAGC823 MAE33421 MAE45168
BA698362 KGABM950 KGACJ761 KGAGC826 MAE33506 MAE45242
BA698592 KGABN395 KGACJ781 KGAGD838 MAE33536 MAE45436
BA727675 KGABP153 KGACK214 KGAGF007 MAE33555 MAE45487
BA727681 KGABP223 KGACL342 KGAJ1662 MAE33632 MAE45513
BA879643 KGABR498 KGACM579 KGAJ1983 MAE33717 MAE45549
BA879645 KGABR930 KGACM61 KGAJ2526 MAE33746 MAE45559
BB104269-C KGABR933 KGACN024 KGAJ3481 MAE38461 MAE45601
BB308730-Y KGABT756 KGACP476 KGAJ3580 MAE38556 MAE45605
DA316476 KGABT780 KGACP627 KGAJ4288 MAE38582 MAE45724
KGA81805 KGABU050 KGACR351 KGAJ4981 MAE38991 MAE45769
KGA82097 KGABU057 KGACR754 KGAJ9582 MAE39057 MAE45781
KGA82487 KGABU059 KGACS814 KGAK0264 MAE39447 MAE45989
KGA82812 KGABU153 KGACT275 KGAK0437 MAE39574 MAE46061
KGA93293 KGABU160 KGACT638 KGAK0742 MAE39625 MAE46388
KGABA101 KGABV741 KGACT706 KGAK0759 MAE39627 MAE46430
KGABA212 KGABW559 KGACT838 KGAK1992 MAE39646 MAE46654
KGABA404 KGABW619 KGACT960 KGAK2064 MAE39674 MAE46976
KGABA424 KGABW790 KGACT969 KGAK2536 MAE39679 MAE46987
KGABA471 KGABW865 KGACU100 KGAK4364 MAE39692 MAE47652
September 27, 2017 CF34-BJ S/B 72-0306
PAGE 11
GE PROPR IETARY INFORMATION - Subject to the restrictions on the cover or ¿rst page.

### Page 12

ENGINE - Fan Rotor Assembly (72-21-00) - Replacement of Fan Blades with Missing
after-Repair Lance Peening
Serial
Number
Serial
Number
Serial
Number
Serial
Number
Serial
Number
Serial
Number
KGABA483 KGABY078 KGACU116 KGAK4443 MAE39914 MAE47766
KGABA484 KGABY754 KGACU685 KGAK4622 MAE40019 MAE47907
KGABA485 KGABY844 KGACV266 KGAK5679 MAE40173 MAE47942
KGABA486 KGACB633 KGACW215 KGAK6257 MAE40634 MAE48137
KGABA489 KGACB654 KGACW513 KGAK6581 MAE40993 MAE48647
KGABA747 KGACB754 KGACW567 KGAK7804 MAE41153 MAE48825
KGABB308 KGACC718 KGACW771 KGAK7813 MAE41367 MAE48899
KGABC152 KGACC790 KGACY111 KGAK7913 MAE41485 MAE48904
KGABC471 KGACC972 KGACY514 KGAK8310 MAE42112 MAE49112
KGABC545 KGACD678 KGACY970 KGAK9370 MAE42318 MAE60227
KGABD151 KGACE429 KGADW416 KGAR2374 MAE42368 MAE60678
KGABD174 KGACF134 KGAG0838 KGAR3200 MAE42457 --
KGABD640 KGACF765 KGAGA109 KGAR4727 MAE42514 --
KGABE093 KGACG331 KGAGA852 KGAR5704 MAE42525 --
September 27, 2017 CF34-BJ S/B 72-0306
PAGE 12
GE PROPR IETARY INFORMATION - Subject to the restrictions on the cover or ¿rst page.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
