# General Electric Service Bulletin 72-0341: Revision R02

- Rights: © General Electric Company. Filed by the FAA in regulations.gov docket FAA-2024-1885, the docket of AD 2025-14-03. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [General Electric Service Bulletin 72-0341](https://openairdocs.org/service-documents/ge/sb-72-0341.md)
- Title as filed: GE Service Bulletin 72-0341_Rev 2
- Pages: 13
- PDF: https://openairdocs.org/files/sha256/5b/0b/5b0b4298753a5d347f9bcde50da3aef1e3106a3f1873497c1896561b682f4423
- Page: https://openairdocs.org/service-documents/ge/sb-72-0341/file/5b0b4298753a

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

CF34-10E Service Bulletins (SBs)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
Date Printed:
2022/10/31
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
reproduced without the express written consent of GE. Technical data is
considered ITAR and/or EAR controlled; transfer of this data to a Non-US
Person, without USG authorization, is strictly prohibited.
Page
1 of 13
CF34-10E SERVICE BULLETIN - 72-0341 R02 Revised:09/24/2021
SB 72-0341 R02 ENGINE - HIGH PRESSURE TURBINE ROTOR ASSEMBLY (72-52-00) -
INSPECTION OF HPT FRONT ROTATING AIR SEAL
Issued:
03/29/2018
GE Designated: -CONFIDENTIAL-
The information contained in this document is GE proprietary information and is
disclosed in confidence. It is the property of GE and shall not be used, disclosed to
others or reproduced without the express written consent of GE, including, but without
limitation, it is not to be used in the creation, manufacture, development, or
derivation of any repairs, modifications, spare parts, designs, or configuration
changes or to obtain FAA or any other government or regulatory approval to do so. If
consent is given for reproduction in whole or in part, this notice and the notice set
forth on each page of this document shall appear in any such reproduction in whole or
part.
This technical data is considered subject to the Export Administration Regulations
(EAR) pursuant to 15 CFR Parts 730-774. Transfer of this data by any means to a
Non-U.S. Person, whether in the United States or abroad, without the proper U.S.
Government authorization (e.g., License, exemption, NLR, etc.), is strictly
prohibited.
Copyright (2021) General Electric Company, U.S.A.
TRANSMITTAL INFORMATION
REVISION 2 TO SERVICE BULLETIN 72-0341
Revision 2 is issued to update paragraph 3., .ACCOMPLISHMENT INSTRUCTIONS
Revision 1 was issued May 12, 2020. The original was issued March 29, 2018. Revision
bars in the left margin identify changes.
1. PLANNING INFORMATION
A. Effectivity
* * * CF34-10E
This Service Bulletin is applicable to these CF34-10E engines:
*CF34-10E engines, serial numbers 994111 through 994999 and 424101 and up.
These serial numbers are the best available data.
This Service Bulletin is applicable to all CF34-10E engines that have installed
the high pressure turbine (HPT) front rotating air seals P/N , P/N 1865M49P04
, and P/N . This includes any engines affected by CF34-10E2448M30P02 2448M30P03
S/B .72-0347
B. Description
This Service Bulletin provides additional inspection procedures for the
affected HPT front rotating air seals.
In addition, this Service Bulletin provides instructions to replace the
affected HPT rotor disk with a new or serviceable HPT rotor disk if the focused
fluorescent penetrant inspection (FPI) reveals indications that extend beyond
rabbet diameter M.
C. Compliance
Category 4
GE recommends that you do this Service Bulletin when the HPT rotor assembly is
exposed.
Impact A
This recommendation is to address a condition that may affect Flight Safety.
NOTE:This Service Bulletin can be accomplished in shop.
This Service Bulletin is offered to improve the reliability or performance of
your GE product, or to help prevent the occurrence of the event or condition

### Page 2

CF34-10E Service Bulletins (SBs)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
Date Printed:
2022/10/31
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
reproduced without the express written consent of GE. Technical data is
considered ITAR and/or EAR controlled; transfer of this data to a Non-US
Person, without USG authorization, is strictly prohibited.
Page
2 of 13
described in this Service Bulletin. If the operator elects not to participate
in the bulletin, that decision will be taken into consideration by GE in
evaluating future product performance issues that may arise in the operator's
fleet.
D. Concurrent Requirements
None.
E. Reason
(1) Objective:
To improve reliability and remove parts from service.
(2) Condition:
The HPT front rotating air seals P/N  and P/N  have been found with1865M49P04 2448M30P02
cracking out of the rabbet where the part interacts with the HPT rotor disk P/N .1865M51P03
To date, two HPT front rotating air seals have been found with this condition.
The fielded parts have been found with cracking out of the rabbet where the part interacts
with the HPT rotor disk. To date, two parts have been found with this condition.
(3) Cause:
The crack initiation location is not always exposed or inspected when the module is exposed
at shop visits.
(4) Inspection:
This Service Bulletin is intended to add an FPI of rabbet diameter M for the HPT front
rotating air seal when the HPT rotor assembly is exposed.
(5) Substantiation:
Substantiation is by fleet experience.
F. Approval
This Service Bulletin contains no modification information that revises the
approved configuration and therefore does not require FAA or regulatory
approval.
G. Manpower
After you get access to the HPT front rotating air seal, you will need
approximately 1 man-hour for each engine or component.
H. Weight and Balance
Weight and balance are not changed.
I. References (Use the latest version of these documents)
CF34 Turbofan Engine Service Record
GEK 9250, Commercial Engine Standard Practices Manual (SPM)
GEK 112081, CF34-10E Engine Manual (EM)
GEK 112082, CF34-10E Illustrated Parts Catalog (IPC)
CF34-10E S/B , ENGINE - High Pressure Turbine Rotor Assembly (72-52-00)72-0347
- HPT Front Rotating Air Seal Correction Plan
J. Publications Affected
GEK 112081, CF34-10E Engine Manual (EM)
K. Interchangeability
Not applicable.
L. Software Accomplishment Summary
Not applicable.
2. MATERIAL INFORMATION
A. Material - Price and Availability
(1) Parts necessary to do this Service Bulletin:
None.
(2) Other Spare Parts:
Part Number Qty/ Eng Part Name Unit ($) Price 
Pkg
Qty Lead Time Days
2448M30P02 (1) Rotating Air Seal,
High Pressure
235,400.00 (1) 5
OR
2448M30P03 (1) Rotating Air Seal,
High Pressure
Quote (-) Quote
1865M51P03 (1) Disk, High Pressure
Turbine Rotor
Quote (-) Quote
OR
1865M51P04 (1) Disk, High Pressure
Turbine Rotor
260,000.00 (1) 5
NOTE:Prices are provided for planning purposes and are subject to change.
(3) Consumables:

### Page 3

CF34-10E Service Bulletins (SBs)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
Date Printed:
2022/10/31
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
reproduced without the express written consent of GE. Technical data is
considered ITAR and/or EAR controlled; transfer of this data to a Non-US
Person, without USG authorization, is strictly prohibited.
Page
3 of 13
None.
B. Industry Support Information
Contact your Customer Support Manager (CSM). Refer to D-0633, Incremental 1.
C. Configuration Chart
None.
D. Parts Disposition
None.
E. Tooling - Price and Availability
None.
3. ACCOMPLISHMENT INSTRUCTIONS
A. General
NOTE:This procedure gives additional inspections to be done on the HPT front rotating air seal (
 when you get access to the HPT rotor assembly.Figure 1)
B. Aft Rabbet Diameter Inspection of HPT Front Rotating Air Seal
(1) Do an FPI of the HPT front rotating air seal. Refer to and do as follows:Figure 2 
(a) Clean the HPT front rotating air seal. Refer to GEK 112081, 72-52-08, CLEANING 001.
(b) Before you do the FPI, swab etch the rabbet diameter M. Refer to GEK 9250, 70-24-01,
SWAB ETCHING PROCEDURE and do as follows:
1 Use Class C etchant.
(c) Do a focused Class G FPI of the boltholes. The boltholes are a very important area.
Refer to GEK 9250, 70-32-02, FLUORESCENT PENETRANT INSPECTION.
(d) Do a Class G FPI of the remaining areas of the HPT front rotating air seal. Refer to
GEK 9250, 70-32-02, FLUORESCENT PENETRANT INSPECTION.
(e) Examine the very important areas of the HPT front rotating air seal. The very important
areas are the bore, inducer holes, rabbet fillets, and retainer rabbet fillets.
(f) Do a focused Class G FPI of the rabbet diameter M. Refer to GEK 9250, 70-32-02,
FLUORESCENT PENETRANT INSPECTION or 70-32-03, SPOT-FLUORESCENT-PENETRANT INSPECTION and
do as follows:
1 Use non-aqueous wet developer (NAWD).
NOTE:Shops can use the method that best provides detectability for small indications.
(g) Indications that are more than 0.015 in. (0.38 mm) are not permitted. If you find
indications that are more than 0.015 in. (0.38 mm), replace the HPT front rotating air
seal. Refer to GEK 112081, 72-52-00, DISASSEMBLY 001 and ASSEMBLY 001.
(h) Linear indications are not permitted. If you find linear indications, replace the HPT
front rotating air seal. Refer to GEK 112081, 72-52-00, DISASSEMBLY 001 and ASSEMBLY
001.
NOTE:Linear indications are indications that are four times longer than they are in width.
(i) If there are indications that extend more than the rabbet diameter M, refer to Figure
 and do as follows:4
1 Discard the HPT rotor disk.
2 Replace the HPT rotor disk with a new or serviceable HPT rotor disk.
NOTE:Figure 5,  and  show typical focused FPI indications onFigure 7, Figure 8
rabbet diameter M and  shows typical fretting on rabbet diameter M.Figure 6
(j) Do an eddy current inspection of the bore surfaces of the HPT front rotating air seal.
Refer to GEK 112081, 72-52-08, INSPECTION 001, Subtask 72-52-08-250-004 through Subtask
72-52-08-250-005.
C. Deleted
D. Service Record Entry
(1) Make an entry in the CF34 Turbine Engine Service Record as follows:
(a) Record compliance to this Service Bulletin in the Engine Service Records, Section II
(Service Bulletins).
(b) Send all important indication findings to the current CF34-10 HPT Fleet Engineer.

### Page 4 (OCR)

CF34-10E Service Bulletins (SBs)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
—SURF. L
DIM. AG -  -DIM. N
SEAL
AIR  TEETH  RETAINER  BLADE
HOLES  AREA
BOLT  DIA M
"HOLES
DIAL DIAM  DIA G
DIA R
DIALE  SEAL
BORE  TOOTH
+
SEAL  TEETH  DAD  DIA B
HPT FRONT
ROTATING  FORWARD MOUNTING FLANGE  AFT MOUNTING FLANGE
AIR SEAL  (DOES NOT INCLUDE FILLET  (DOES NOT INCLUDE
NEXT TO DIA DI  FILLET NEXT TO DIA B)
BORE•
*BORE
FACE
FACE
-SURF. A
SURF. C→
B-B  5050579-00
HPT Front Rotating Air Seal
Figure 1
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/10/31  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  4 of 13
[Person, without USG authorization, is strictly prohibited.

### Page 5 (OCR)

CF34-10E Service Bulletins (SBS)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
RETAINER
RABBET FILLET
INDUCER
HOLE
RABBET
FILLETS  -BOLTHOLE
BORE
5050577-00
FPI of the HPT Front Rotating Air Seal
Figure 2 (Sheet 1)
PROPRIETARY INFORMATION - Not to be used, disclosed to others or
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/10/31  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  5 of 13
Person, without USG authorization, is strictly prohibited.

### Page 6 (OCR)

CF34-10E Service Bulletins (SBs)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
ZONE E
ZONE G
ZONE G
ZONE E
INDUCER  HOLE  ZONE F
ZONE G
ZONE E
ZONE G
- BOLTHOLE
ZONE F
ZONE F
NOTES:
1. DIFFERENT ZONES ARE DEFINED
AS FOLLOWS:
ZONE E:
ZONE F:-
ZONE G:
2. THESE ZONES DO NOT APPLY INSIDE THE INDUCER HOLE AND THE BOLTHOLE.
3. ZONE F APPLIES BETWEEN THE INDUCER HOLES IN THE CIRCUMFERENTIAL
DIRECTION AND BETWEEN THE BOLTHOLES IN THE CIRCUMFERENTIAL DIRECTION.  5050576-00
FPI of the HPT Front Rotating Air Seal
Figure 2 (Sheet 2)
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/10/31  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  6 of 13
Person, without USG authorization, is strictly prohibited.

### Page 7 (OCR)

CF34-10E Service Bulletins (SBs)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
FIGURE DELETED
99de0011
Deleted
Figure 3
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/10/31  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  7 of 13
[Person, without USG authorization, is strictly prohibited.

### Page 8 (OCR)

CF34-10E Service Bulletins (SBs)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
B
HPT FRONT
_ ROTATING
AIR SEAL
B-B
6009727-00
Interpretation of Linear Indications for Diameter M
Figure 4 (Sheet 1)
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
Date Printed:  reproduced without  the express written consent of GE. Technical data  Page
2022/10/31  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  8 of 13
Person, without USG authorization, is strictly prohibited.

### Page 9 (OCR)

CF34-10E Service Bulletins (SBS)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
LINEAR INDICATIONS
RETAINER
RABBET
FILLET  DIA M
6
4 5
RETAINER AFT FACE
INDICATION  LINEAR  CASE  DESCRIPTION  REPLACE HPT  ROTOR DISK?
LINEAR INDICATIONS
EXTEND BEYOND
1  DIA M INTO THE RETAINER  YES
AFT FACE
2  NO
LINEAR INDICATIONS
DO NOT EXTEND  NO
BEYOND DIA M
4  NO
5  NO
6  NO
LINEAR INDICATIONS
7  EXTEND BEYOND  YES
DIA MINTO THE RETAINER
RABBET FILLET
6009728-00
Interpretation of Linear Indications for Diameter M
Figure 4 (Sheet 2)
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/10/31  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  9 of 13
Person, without USG authorization, is strictly prohibited.

### Page 10 (OCR)

CF34-10E Service Bulletins (SBs)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
DIA M
6009277-00
Typical Focused FPI Indigations on Rabbet Diameter M
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/10/31  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  10 of 13
[Person, without USG authorization, is strictly prohibited.

### Page 11 (OCR)

CF34-10E Service Bulletins (SBS)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
6009278-00
Typical Fretting on Rabbet Diameter M
Figure 6
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/10/31  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  11 of 13
[Person, without USG authorization, is strictly prohibited.

### Page 12 (OCR)

CF34-10E Service Bulletins (SBS)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
6028185-00
Typical Focused FPI Linear Indication on Rabbet Diameter M Observed With 10x
Magnification
Figure 7
GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/10/31  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  12 of 13
[Person, without USG authorization, is strictly prohibited.

### Page 13 (OCR)

CF34-10E Service Bulletins (SBs)
SB 72-0341 R02 ENGINE - High Pressure Turbine Rotor Assembly (72-52-00) - Inspection of HPT Front Rotating
Air Seal
FPI OBSERVATION
WHITE LIGHT INSPECTION OBSERVATION
6028186-00
Typical Focused FPI Linear Indication on Rabbet Diameter M and Same Indication as
Observed with White Light Inspection
Figure 8
GE Designated: - CONFIDENTIAL Subject to the restrictions on the media
PROPRIETARY INFORMATION - Not to be used, disclosed to others
Date Printed:  reproduced without the express written consent of GE. Technical data  Page
2022/10/31  considered ITAR and/or EAR controlled; transfer of this data to a Non-US  13 of 13
Person, without USG authorization, is strictly prohibited.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
