# General Electric Service Bulletin 73-0038: No revision named

- Rights: © General Electric Company. Filed by the FAA in regulations.gov docket FAA-2018-0633, the docket of AD 2018-21-12. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [General Electric Service Bulletin 73-0038](https://openairdocs.org/service-documents/ge/sb-73-0038.md)
- Title as filed: GEnx-2B-SB-73-0038-R03
- Pages: 28
- PDF: https://openairdocs.org/files/sha256/c0/f6/c0f6af4b7bf35272ba300ff3ecfeb98443997daa04ef07be59594eecf85bd15d
- Page: https://openairdocs.org/service-documents/ge/sb-73-0038/file/c0f6af4b7bf3

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
1 of 28
GEnx-2B SERVICE BULLETIN - 73-0038 R03 Revised:08/17/2018
SB 73-0038 R03 ENGINE FUEL AND CONTROL - FUEL NOZZLE
MANIFOLDS (73-11-40) - INTRODUCTION OF NEW FUEL MANIFOLD
SYSTEM HARDWARE
Issued:
05/11/2015
GE PROPRIETARY INFORMATION
The information contained in this document is GE proprietary
information and is disclosed in confidence. It is the property of GE
and shall not be used, disclosed to others or reproduced without the
express written consent of GE, including, but without limitation, it is
not to be used in the creation, manufacture, development, or derivation
of any repairs, modifications, spare parts, designs, or configuration
changes or to obtain FAA or any other government or regulatory approval
to do so. If consent is given for reproduction in whole or in part,
this notice and the notice set forth on each page of this document
shall appear in any such reproduction in whole or in part.
This technical data is considered EAR controlled pursuant to 15 CFR
Parts 730-774 respectively. Transfer of this data by any means to a
Non-US Person, whether in the United States or abroad, without the
proper U.S. Government authorization (e.g., License, exemption, NLR,
etc.), is strictly prohibited.
Copyright (2018) General Electric Company, U.S.A.
TRANSMITTAL INFORMATION
REVISION 3 TO SERVICE BULLETIN 73-0038
Revision 3 is issued to update paragraphs 1., , 2.,PLANNING INFORMATION
, and 3., .MATERIAL INFORMATION ACCOMPLISHMENT INSTRUCTIONS
Revision 2 was issued November 19, 2015. Revision 1 was issued July 15,
2015. The original was issued May 11, 2015. Revision bars in the left
margin identify changes.
1. PLANNING INFORMATION
A. Effectivity
* * * GEnx-2B67, -2B67B, -2B67/P
This Service Bulletin is applicable to all GEnx-2B engines.
This Service Bulletin has been introduced in production to these
GEnx-2B engines:
*GEnx-2B engines, serial numbers 959-521 and up.
These serial numbers are the best available data.
Incorporation of this change will result in the termination of
inspection as defined in GEnx-2B S/B . This Service73-0034
Bulletin eliminates the need to replace the top main and lower
fuel manifolds in the shop specified in GEnx-2B S/B .73-0030

### Page 2

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
2 of 28
The top main fuel manifolds (fuel manifolds) P/N , P/N 2419M11G01
, and P/N  and lower fuel manifolds (fuel2561M11G01 2546M11G01
manifolds) P/N , P/N , and P/N  are2419M12G01 2561M12G01 2546M12G01
affected by this Service Bulletin.
Post-GEnx-2B S/B  engines have the upper fuel manifold73-0079
already replaced with the new configuration released in this
Service Bulletin.
B. Description
This Service Bulletin provides new fuel manifold system hardware
to address a field durability issue. The new upper and lower
manifold require installation of new support brackets and spring
packs to permit additional movement of the manifold during
operation.
Installation of the new hardware permits termination of the field
inspection released by GEnx-2B S/B  as well as replacement73-0034
of the fuel manifold released by GEnx-2B S/B . With73-0030
installation of this new hardware, there is no further need to
perform ultrasonic inspection of the fuel manifolds.
GEnx-2B S/B  allows an intermixed configuration and this73-0079
Service Bulletin (GEnx-2B S/B 73-0038 Revision 3) provides
instructions to replace the lower fuel manifold to fully
implement the introduction of the new fuel manifold system to
post-GEnx-2B 73-0079 engines.
C. Compliance
Category 3
GE recommends that you do this Service Bulletin at the next shop
visit of the engine.
Impact B
This recommendation is to address a condition that may result in
an Increased Rate of In-Flight Shutdowns (IFSD), Take-Off Aborts
(TOA), Air Turn Backs (ATB) or Diversions (DIV).
NOTE:This Service Bulletin must be accomplished in shop.
NOTE:This Service Bulletin can be accomplished in the hangar using pedestals or a
shipping stand with the engine removed from the aircraft.
This Service Bulletin is offered to improve the reliability or
performance of your GE product, or to help prevent the occurrence
of the event or condition described in this Service Bulletin. If
the operator elects not to participate in the bulletin, that
decision will be taken into consideration by GE in evaluating
future product performance issues that may arise in the
operator's fleet.
D. Concurrent Requirements
Do GEnx-2B S/B  when you do this Service Bulletin.73-0039
E. Reason
(1) Objective:
To introduce new parts, improve reliability, improve maintainability,
remove parts from service, and reduce significant events.
(2) Condition:
Recent field events have led to increased finding of fuel manifold defects.
Defects have been found in the fuel manifolds adjacent to the support
blocks that can lead to leaks during operation. Currently, fuel manifolds
are being replaced in the shop as specified in GEnx-2B S/B . A73-0030

### Page 3

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
3 of 28
recent fuel manifold inspection campaign introduced by GEnx-2B S/B 73-0034
is being used to identify parts with defects before leaking is detected.
The GEnx-2B S/B  is used to replace fuel manifolds on wing.72-0108
(3) Cause:
The investigation determined the fuel manifold support brackets do not
allow sufficient clearance to account for thermal expansion and contraction
in the fuel manifold system.
(4) Improvement:
The support brackets are being changed to allow sufficient clearance for
worst case assembly/manufacturing stack-up tolerances and thermal movement
which will address the field issue.
(5) Substantiation:
Substantiation is by analysis and comparative analysis.
F. Approval
The data contained in this Service Bulletin has been reviewed by
the appropriate governmental authority and the repair(s) and
modification(s) herein comply with the applicable Aviation
Regulations and are APPROVED for installation in the model(s)
listed in this Service Bulletin.
G. Manpower
After you get access to the engine, you will need approximately
220 man-hours for each engine to accomplish this Service
Bulletin.
H. Weight and Balance
The complete compliance with this Service Bulletin increases
weight by 2.0 lb (0.9 kg).
I. References (Use the latest version of these documents)
GEnx-2B, Boeing 747-8 Aircraft Maintenance Manual (AMM)
GEK 9250, Commercial Engine Standard Practices Manual (SPM)
GEK 114119, GEnx-2B Engine Manual (EM)
GEK 114120, GEnx-2B Cleaning, Inspection, and Repair Manual (CIR)
GEK 114122, GEnx-2B Engine Illustrated Parts Catalog (EIPC)
GEnx-2B S/B , ENGINE FUEL AND CONTROL - Fuel Nozzle72-0108
Manifolds (73-11-40) - Replacement of the Top and/or Lower Fuel
Manifolds
GEnx-2B S/B , ENGINE - General (72-00-00) - GEnx-2B/P72-0144
Hardware Release (Propulsor Hardware)
GEnx-2B S/B , ENGINE FUEL AND CONTROL - Fuel Nozzle73-0030
Manifolds (73-11-40) - Introduction of New Top and Lower Fuel
Manifolds
GEnx-2B S/B , ENGINE FUEL AND CONTROL - Fuel Nozzle73-0034
Manifolds (73-11-40) - Fuel Manifold Field Inspection
GEnx-2B S/B , ENGINE FUEL AND CONTROL - Fuel Injection73-0039
Nozzles (73-11-30) - Introduction of New Brackets for Upper Fuel
Manifold Inlet Support Improvement
GEnx-2B S/B , ENGINE FUEL AND CONTROL - General (73-00-00)73-0079
- Fuel Manifold Intermix on GEnx-2B Engines
GEnx-2B S/B , AIR - Air System (75-00-00) - OBV System75-0015
Removal
NOTE:The reference documents listed below are for the engine manufacturer's
internal use only:
CID: 575295, 575295-3, 575440
BPP: 14-72-40-03, 18-72-00-76010

### Page 4

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
4 of 28
J. Publications Affected
GEnx-2B, Boeing 747-8 Aircraft Maintenance Manual (AMM)
GEK 114119, GEnx-2B Engine Manual (EM)
GEK 114120, GEnx-2B Cleaning, Inspection, and Repair Manual (CIR)
GEK 114122, GEnx-2B Engine Illustrated Parts Catalog (EIPC)
K. Interchangeability
The proposed and superseded configurations of the fuel manifold
system sections can be introduced in partial engine sets (upper
and lower sections) depending on the engine to be retrofitted. As
defined in paragraph , some components2.C., Configuration Chart
in this system are different, depending on whether the engine is
a GEnx-2B67 and GEnx-2B67B base configurations or GEnx-2B67/P
configuration (post-GEnx-2B S/B ).72-0144
The support bracket at location SIN 61A12 uses P/N  for2623M89G01
GEnx-2B pre-S/B  and uses P/N  for GEnx-2B72-0144 2623M88G01
post-S/B .72-0144
The support bracket at location SIN 61A13 uses P/N  for2623M90G01
GEnx-2B pre-S/B  and GEnx-2B post-S/B  that72-0144 72-0144
includes GEnx-2B S/B . For GEnx-2B post-S/B 75-0015 72-0144
engines that do not include GEnx-2B S/B , use P/N 75-0015
.2623M91P01
L. Software Accomplishment Summary
Not applicable.
2. MATERIAL INFORMATION
A. Material - Price and Availability
(1) Parts necessary to do this Service Bulletin:
(a) For pre-GEnx-2B S/B  configuration:73-0079
Part Number
Qty/
Eng Part Name
Unit ($)
Price Pkg Qty
Lead
Time
Days
RPK341G01 (1) Kit, Fuel Manifold
System
GEnx-2B67/
-2B67B
Quote (-) Quote
NOTE:The following parts are included in the fuel manifold system kit P/N .RPK341G01
It is not necessary to order these parts separately.
2620M81G01 (6) Bracket, Support 703.00 (1) 5
2623M81G01 (2) Bracket, Support 1,313.00 (1) 5
2623M82G01 (1) Bracket, Support 1,035.00 (1) 5
2414M82P01 (10) Spring 37.00 (1) 5
2620M93P01 (10) Slider, Spring 176.25 (1) 5
2623M83P01 (10) Dampener 176.25 (1) 5
2613M58P01 (1) Bracket, Support 3,508.00 (1) 5
2613M59G01 (1) Bracket, Support 1,965.00 (1) 5
2623M87G01 (1) Bracket, Stage 4/7
Stub Assembly
1,070.00 (1) 5
2623M89G01 (1) Bracket, Support 1,459.00 (1) 5
2623M90G01 (1) Bracket 1,459.00 (1) 5
2623M75G01 (1) Bracket, Machined 13,000.00 (1) 5
2623M71G01 (1) Manifold, Top Main
Fuel
41,750.00 (1) 30

### Page 5

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
5 of 28
2619M58G01 (1) Manifold, Lower Fuel 41,750.00 (1) 5
2623M84P01 (1) Bracket, Support 875.00 (1) 5
2636M78G01 (1) Bracket 875.00 (1) 5
OR
RPK342G01 (1) Kit, Fuel Manifold
System (PIP with
OBV)
Quote (-) Quote
NOTE:The following parts are included in the fuel manifold system kit P/N .RPK342G01
It is not necessary to order these parts separately.
2620M81G01 (6) Bracket, Support 703.00 (1) 5
2623M81G01 (2) Bracket, Support 1,313.00 (1) 5
2623M82G01 (1) Bracket, Support 1,035.00 (1) 5
2414M82P01 (10) Spring 37.00 (1) 5
2620M93P01 (10) Slider, Spring 176.25 (1) 5
2623M83P01 (10) Dampener 176.25 (1) 5
2613M58P01 (1) Bracket, Support 3,508.00 (1) 5
2613M59G01 (1) Bracket, Support 1,965.00 (1) 5
2623M87G01 (1) Bracket, Stub
Assembly Stage 4/7
1,070.00 (1) 5
2623M88G01 (1) Bracket, Support 1,459.00 (1) 5
2623M91P01 (1) Bracket 688.00 (1) 5
2623M75G01 (1) Bracket, Machined 13,000.00 (1) 5
2623M71G01 (1) Manifold, Top Main
Fuel
41,750.00 (1) 30
2619M58G01 (1) Manifold, Lower Fuel 41,750.00 (1) 5
2623M84P01 (1) Bracket, Support 875.00 (1) 5
2636M78G01 (1) Bracket, Support 875.00 (1) 5
OR
RPK343G01 (1) Kit, Fuel Manifold
System (PIP without
OBV)
Quote (-) Quote
NOTE:The following parts are included in the fuel manifold system kit P/N .RPK343G01
It is not necessary to order these parts separately.
2620M81G01 (6) Bracket, Support 703.00 (1) 5
2623M81G01 (2) Bracket, Support 1,313.00 (1) 5
2623M82G01 (1) Bracket, Support 1,035.00 (1) 5
2414M82P01 (10) Spring 37.00 (1) 5
2620M93P01 (10) Slider, Spring 176.25 (1) 5
2623M83P01 (10) Dampener 176.25 (1) 5
2613M58P01 (1) Bracket, Support 3,508.00 (1) 5
2613M59G01 (1) Bracket, Support 1,965.00 (1) 5
2623M87G01 (1) Bracket, Stub
Assembly Stage 4/7
1,070.00 (1) 5
2623M88G01 (1) Bracket, Support 1,459.00 (1) 5
2623M90G01 (1) Bracket 1,459.00 (1) 5
2623M75G01 (1) Bracket, Machined 13,000.00 (1) 5
2623M71G01 (1) Manifold, Top Main
Fuel
41,750.00 (1) 30
2619M58G01 (1) Manifold, Lower Fuel 41,750.00 (1) 5

### Page 6

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
6 of 28
2623M84P01 (1) Bracket, Support 875.00 (1) 5
2636M78G01 (1) Bracket, Support 875.00 (1) 5
NOTE:The following parts are not in the kit but are required to support the
replacement of the fuel manifold on the GEnx-2B67 and GEnx-2B67B engine
configurations:
2105M78P01 (4) Seal Ring, Metal 608.00 (1) 5
AS1895-1-350~ (2) Coupling, Seal NP (-) --
AS1895-23-300~ (1) Seal Ring NP (-) --
AS1895-23-350~ (2) Seal Ring NP (-) --
AS1895-23-150~ (1) Seal Ring NP (-) --
J222P015 (1) Packing 1.25 (50) 5
J222P016 (2) Packing 1.25 (50) 5
J222P018 (3) Packing Preformed 4.25 (1) 5
J1215P24 (1) Gasket Flange 65.25 (10) 5
2459M14P01 (2) Seal Outer 2,484.00 (1) 5
AS1895-23-250~ (4) Seal Ring NP (-) --
AS1895-23-175~ (8) Seal Ring NP (-) --
2105M91P01 (4) Seal Ring 400.00 (1) 5
J222P013 (44) Packing, Preformed 1.50 (50) 5
J222P009 (4) Packing 1.70 (1) 5
BACP18BC03B08P# (5) Cotter Pin (Boeing) NP (-) --
2105M47P01 (3) Gasket, FMU Seal 499.25 (1) 5
2114M29P01 (1) Gasket, Seal 5,249.00 (1) 5
2-216V1041-85~ (1) Packing NP (-) --
2256M86P01 (2) Seal Assembly 476.50 (1) 5
2377M79P01 (1) Gasket, Flange Seal 400.75 (1) 5
2443M18P01 (1) Gasket, Seal 535.00 (1) 5
2492M87P01 (1) Gasket, Seal 1,245.00 (1) 5
AS1895-7-450~ (2) Seal, Ring NP (-) --
J1215P17 (4) Gasket 69.00 (5) 5
J1215P20 (8) Gasket 96.25 (5) 5
J1215P24 (2) Gasket, Flange Seal 65.25 (10) 5
J1215P28 (1) Gasket, Preformed 70.00 (5) 5
J1215P32 (3) Gasket, Flange Seal 281.75 (1) 5
J1411P06 (47) Nut, Double
Self-Locking
129.00 (10) 5
J1438P125 (2) Packing 260.25 (1) 5
J1438P134 (1) Packing, Preformed 21.00 (1) 5
J1438P151 (1) Packing, Preformed 58.75 (1) 5
J1438P163 (1) Packing, Preformed 31.50 (1) 5
J221P222 (2) Packing, Preformed 3.45 (25) 5
J222P015 (2) Packing, Preformed 1.25 (50) 5
J222P016 (2) Packing, Preformed 1.25 (50) 5
J222P018 (4) Packing, Preformed 4.25 (1) 5
J222P120 (4) Packing, Preformed 5.25 (25) 5
J222P124 (2) Gasket, Preformed 2.50 (25) 5

### Page 7

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
7 of 28
M83485-1-012~ (1) Packing, Preformed NP (-) --
M83485-1-225~ (1) Packing, Preformed NP (-) --
M83485-1-261~ (1) Packing, Preformed NP (-) --
9048156* (2) Seal, Silicone NP (-) --
1337M46P11 (AR) Gasket, Igniter Plug 12.50 (20) 5
AS1895-23-125~ (1) Seal Ring NP (-) --
2304M79P01 (2) Gasket, Seal 56.75 (1) 5
J1215P10 (1) Gasket, Flange Seal 305.25 (1) 5
2364M47P01 (2) Gasket, Flange Seal 225.25 (1) 5
NOTE:The following parts are not in the kit but are required to support the
replacement of the fuel manifold on the GEnx-2B67/P engine configuration:
2105M47P01 (3) Gasket, FMU Seal 499.25 (1) 5
2105M78P01 (8) Seal Ring, Metal 608.00 (1) 5
2105M91P01 (4) Seal 400.00 (1) 5
2114M29P01 (1) Gasket, Seal 5,249.00 (1) 5
2255M93P01 (22) Seal Assembly 880.00 (1) 5
2256M86P01 (2) Seal Assembly 476.50 (1) 5
2377M79P01 (1) Gasket, Flange Seal 400.75 (1) 5
2443M18P01 (1) Gasket, Seal 535.00 (1) 5
2459M14P01 (2) Seal, Outer 2,484.00 (1) 5
2492M87P01 (1) Gasket, Seal 1,245.00 (1) 5
69B90191-4# (1) Gasket NP (-) --
AS1895-23-150~ (3) Seal, Ring NP (-) --
AS1895-23-175~ (12) Seal, Ring NP (-) --
AS1895-23-250~ (4) Seal, Ring NP (-) --
AS1895-23-300~ (1) Seal, Ring NP (-) --
AS1895-23-350~ (2) Seal, Ring NP (-) --
AS1895-7-450~ (2) Seal, Ring NP (-) --
AS1895-7-550~ (2) Gasket NP (-) --
AS3237-14~ (AR) Bolt, Machine NP (-) --
BACG10AD32YC# (1) Gasket NP (-) --
J1215P17 (5) Gasket, Seal Flange 69.00 (5) 5
J1215P20 (7) Gasket, Seal Flange 96.25 (5) 5
J1215P24 (5) Gasket, Seal Flange 65.25 (10) 5
J1215P32 (3) Gasket, Seal Flange 281.75 (1) 5
J1438P125 (2) Packing, Preformed 260.25 (1) 5
J1411P06 (48) Nut, Double
Self-Locking
129.00 (10) 5
J1438P134 (1) Packing, Preformed 21.00 (1) 5
1221P149 (1) Packing, Preformed 65.50 (1) Q
OR
J1438P149 (ALT) Packing, Preformed 65.50 (1) 5
J1438P163 (1) Packing, Preformed 31.50 (1) 5
J221P222 (2) Packing, Preformed 3.45 (25) 5
J222P009 (4) Packing, Preformed 1.70 (1) 5
J222P013 (44) Packing, Preformed 1.50 (50) 5

### Page 8

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
8 of 28
J222P015 (9) Packing, Preformed 1.25 (50) 5
J222P016 (6) Packing, Preformed 1.25 (50) 5
J222P018 (4) Packing, Preformed 4.25 (1) 5
J222P120 (4) Packing, Preformed 5.25 (25) 5
J222P124 (2) Gasket, Preformed 2.50 (25) 5
M83485-1-012~ (1) Packing, Preformed NP (-) --
M83485-1-225~ (1) Packing, Preformed NP (-) --
M83485-1-261~ (2) Packing, Preformed NP (-) --
*Part not supplied by GE Engine Services Distribution L.L.C. To procure
parts, contact the following:
Unison Industries, LLC
7575 Baymeadows Way 
Jacksonville, FL 32256-7525
U.S.A.
Phone: (904) 739-4131
Fax: (904) 739-4006
~Part not supplied by GE Engine Services Distribution L.L.C. Procure
through local purchase.
#Part not supplied by GE Engine Services Distribution L.L.C. Procure
through Boeing Company.
NP = Not Provisioned
NOTE:Prices are provided for planning purposes and are subject to change.
(b) For post-GEnx-2B S/B  configuration:73-0079
Part Number Qty/ Eng Part Name
Unit ($)
Price 
Pkg
Qty
Lead Time
Days
GEnx-2B67/-2B67B
2620M81G01 (3) Bracket, Support 703.00 (1) 5
2623M81G01 (1) Bracket, Support 1,313.00 (1) 5
2414M82P01 (5) Spring 37.00 (1) 5
2620M93P01 (5) Slider, Spring 176.25 (1) 5
2623M83P01 (5) Dampener 176.25 (1) 5
2623M82G01 (1) Bracket, Support 1,035.00 (1) 5
2613M58P01 (1) Bracket, Support 3,508.00 (1) 5
2613M59G01 (1) Bracket, Support 1,965.00 (1) 5
2623M87G01 (1) Bracket, Stage 4/7
Stub Assembly
1,070.00 (1) 5
2619M58G01 (1) Manifold, Lower Fuel 3,508.00 (1) 5
2623M84P01 (1) Bracket, Support 875.00 (1) 5
GEnx-2B67/P with OBV
2620M81G01 (3) Bracket, Support 703.00 (1) 5
2623M81G01 (1) Bracket, Support 1,313.00 (1) 5
2414M82P01 (5) Spring 37.00 (1) 5
2620M93P01 (5) Slider, Spring 176.25 (1) 5
2623M83P01 (5) Dampener 176.25 (1) 5
2623M82G01 (1) Bracket, Support 1,035.00 (1) 5
2613M58P01 (1) Bracket, Support 3,508.00 (1) 5
2613M59G01 (1) Bracket, Support 1,965.00 (1) 5
2623M87G01 (1) Bracket, Stub 1,070.00 (1) 5

### Page 9

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
9 of 28
Assembly Stage
2619M58G01 (1) Manifold, Lower Fuel 41,750.00 (1) 5
2623M84P01 (1) Bracket, Support 875.00 (1) 5
GEnx-2B67/P without OBV
2620M81G01 (3) Bracket, Support 703.00 (1) 5
2623M81G01 (1) Bracket, Support 1,313.00 (1) 5
2414M82P01 (5) Spring 37.00 (1) 5
2620M93P01 (5) Slider, Spring 176.25 (1) 5
2623M83P01 (5) Dampener 176.25 (1) 5
2623M82G01 (1) Bracket, Support 1,035.00 (1) 5
2613M58P01 (1) Bracket, Support 3,508.00 (1) 5
2613M59G01 (1) Bracket, Support 1,965.00 (1) 5
2623M87G01 (1) Bracket, Assembly
Stub
1,070.00 (1) 5
2619M58G01 (1) Manifold, Lower Fuel 41,750.00 (1) 5
2623M84P01 (1) Bracket, Support 875.00 (1) 5
NOTE:The following parts are required to support the replacement of the
lower fuel manifold on the GEnx-2B67 and GEnx-2B67B engine
configurations:
Part Number
Qty/
Eng Part Name
Unit ($)
Price Pkg Qty
Lead Time
Days
2255M93P01 (11) Bracket, Support 880.00 (1) 5
AS1895-23-175~ (12) Seal, Ring NP (-) --
2105M78P01 (2) Seal Ring, Metal 608.00 (1) 5
J222P013 (22) Packing, Preformed 1.50 (50) 5
BACP18BC03B08P# (5) Cotter Pin (Boeing) NP (-) --
2105M47P01 (3) Gasket, FMU Seal 499.25 (1) 5
2114M29P01 (1) Gasket, Seal 5,249.00 (1) 5
2-216V1041-85~ (1) Packing NP (-) --
2377M79P01 (1) Gasket, Flange Seal 400.75 (1) 5
2443M18P01 (1) Gasket, Seal 535.00 (1) 5
2492M87P01 (1) Gasket, Seal 1,245.00 (1) 5
AS1895-7-450~ (2) Seal, Ring NP (-) --
J1215P17 (4) Gasket 69.00 (5) 5
J1215P20 (4) Gasket 96.25 (5) 5
J1215P24 (2) Gasket, Flange Seal 65.25 (10) 5
J1215P28 (1) Gasket, Preformed 70.00 (5) 5
J1215P32 (3) Gasket, Flange Seal 281.75 (1) 5
J1411P06 (24) Nut, Double
Self-Locking
129.00 (10) 5
J1438P125 (2) Packing 260.25 (1) 5
J1438P134 (1) Packing, Preformed 21.00 (1) 5
J1438P151 (1) Packing, Preformed 58.75 (1) 5
J1438P163 (1) Packing, Preformed 31.50 (1) 5
J221P222 (2) Packing, Preformed 3.45 (25) 5
J222P015 (2) Packing, Preformed 1.25 (50) 5
J222P016 (2) Packing, Preformed 1.25 (50) 5

### Page 10

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
10 of 28
J222P018 (4) Packing, Preformed 4.25 (1) 5
J222P120 (4) Packing, Preformed 5.25 (25) 5
J222P124 (2) Gasket, Preformed 2.50 (25) 5
M83485-1-012~ (1) Packing, Preformed NP (-) --
M83485-1-225~ (1) Packing, Preformed NP (-) --
M83485-1-261~ (1) Packing, Preformed NP (-) --
9048156* (2) Seal, Silicone NP (-) --
1337M46P11 (AR) Gasket, Igniter Plug 12.50 (20) 5
AS1895-23-125~ (1) Seal Ring NP (-) --
2304M79P01 (2) Gasket, Seal 56.75 (1) 5
J1215P10 (1) Gasket, Flange Seal 305.25 (1) 5
2364M47P01 (2) Gasket, Flange Seal 225.25 (1) 5
NOTE:The following parts are required to support the replacement of the
lower fuel manifold on the GEnx-2B67/P engine configuration:
Part Number Qty/ Eng Part Name
Unit ($)
Price Pkg Qty
Lead Time
Days
2255M93P01 (11) Seal Assembly 880.00 (1) 5
AS1895-23-175~ (12) Seal, Ring NP (-) --
2105M78P01 (2) Seal Ring, Metal 608.00 (1) 5
AS1895-23-350~ (2) Seal, Ring NP (-) --
AS1895-7-450~ (2) Seal, Ring NP (-) --
AS1895-7-550~ (2) Gasket NP (-) --
AS3237-14~ (AR) Bolt, Machine NP (-) --
BACG10AD32YC# (1) Gasket NP (-) --
J1215P17 (5) Gasket, Seal Flange 69.00 (5) 5
J1215P20 (7) Gasket, Seal Flange 96.25 (5) 5
J1215P24 (5) Gasket, Seal Flange 65.25 (10) 5
J1215P32 (3) Gasket, Seal Flange 281.75 (1) 5
J1438P125 (2) Packing, Preformed 260.25 (1) 5
J1411P06 (24) Nut, Double
Self-Locking
129.00 (10) 5
J1438P134 (1) Packing, Preformed 21.00 (1) 5
1221P149 (1) Packing, Preformed 65.50 (1) Quote
OR
J1438P149 (ALT) Packing, Preformed 65.50 (1) 5
J1438P163 (1) Packing, Preformed 31.50 (1) 5
J221P222 (2) Packing, Preformed 3.45 (25) 5
J222P009 (4) Packing, Preformed 1.70 (1) 5
J222P013 (22) Packing, Preformed 1.50 (50) 5
J222P015 (9) Packing, Preformed 1.25 (50) 5
J222P016 (6) Packing, Preformed 1.25 (50) 5
J222P018 (4) Packing, Preformed 4.25 (1) 5
J222P120 (4) Packing, Preformed 5.25 (25) 5
J222P124 (2) Gasket, Preformed 2.50 (25) 5
M83485-1-012~ (1) Packing, Preformed NP (-) --
M83485-1-225~ (1) Packing, Preformed NP (-) --
M83485-1-261~ (2) Packing, Preformed NP (-) --

### Page 11

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
11 of 28
*Part not supplied by GE Engine Services Distribution L.L.C. To procure
parts, contact the following:
Unison Industries, LLC
7575 Baymeadows Way 
Jacksonville, FL 32256-7525
U.S.A.
Phone: (904) 739-4131
Fax: (904) 739-4006
~Part not supplied by GE Engine Services Distribution L.L.C. Procure
through local purchase.
#Part not supplied by GE Engine Services Distribution L.L.C. Procure
through Boeing Company.
NOTE:Prices are provided for planning purposes and are subject to change.
(2) Other Spare Parts:
Part Number Qty/ Eng Part Name
Unit ($)
Price 
Pkg
Qty
Lead
Time
Days
2330M45G06 (1) Combustor Nozzle
Assembly
Quote (-) Quote
2330M54G06 (1) Combustor Diffuser
Assembly
Quote (-) Quote
NOTE:Prices are provided for planning purposes and are subject to change.
(3) Consumables:
Code Number Description
C02-019 Oil, Engine Lubricating (GE Spec. D50TF1) (engine oil)
C02-023 Oil, Engine Lubricating (MIL-PRF-23699) (engine oil)
C02-033 Petrolatum, Soft (Fed Spec. VV-P-236)
C02-058 Compound, Thread Lubricating (lubricant)
C02-060 Anti-Seize and Lubricating Lithium Base Compound (GE Spec D6Y28A1)
(anti-seize compound)
C04-035 Solvent, General (isopropyl alcohol)
C05-005 Liquid, Leak (Bubble) Test (ASTM E515) (leak detection fluid)
C10-071 Safety Wire, 0.020 or 0.032 in. dia. (safety wire)
C10-143 Safety Cable Assembly (321 Stainless Steel AS 4536, AS 3510) (safety
cable)
B. Industry Support Information
Contact your Customer Support Manager (CSM) for industry support
information.
C. Configuration Chart
New 
Part Number
Qty/
Eng Part Name
Old Part Number/
IPC Location
Qty/
Eng
Op
Code
Chg/
Sprt
Code
2330M20G09/
G10/G11
(X) Assembly,
Propulsor Module
2330M20G09/
G10/G11
(X) RM -/-
.  2620M81G01
 01-071,73-11-40
(6) Bracket, Support
(SIN 34110)
.  2343M87G01
 01-070,73-11-40
(6) RE 5/A
.  2623M81G01
 01-082,73-11-40
(2) Bracket, Support
(SIN 34112)
.  2475M24G01
 01-081,73-11-40
(2) RE 5/A
.  2623M82G01
 01-101,73-11-40
(1) Bracket, Support
(SIN 34117)
.  2381M41G01
 01-100,73-11-40
(1) RE 5/A
.  2620M93P01
 01-131,73-11-40
(10) Slider, Spring
(SIN 34191)
.  2429M18P01
 01-130,73-11-40
(10) RE 5/A

### Page 12

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
12 of 28
.  2623M83P01
 01-151,73-11-40
(10) Dampener
(SIN 34192)
.  2429M19P01
 01-150,73-11-40
(10) RE 5/A
.  2613M58P01
 05-061,79-21-00
(1) Bracket, Support
(SIN 40A10)
.  2426M81P01
 05-060,79-21-00
(1) RE 5/A
.  2613M59G01
 05-091,79-21-00
(1) Bracket, Support
(SIN 40A1B)
.  2363M29G01
 05-090,79-21-00
(1) RE 5/A
.  2623M87G01
 34-241,72-00-02
(1) Bracket, Stage
4/7 Stub Assembly
(SIN 61113)
.  2404M74G01
 34-240,72-00-02
(1) RE 5/A
.  2623M88G01
 02-031,75-31-21
(1) Bracket, Support
(SIN 61A12)
.  2510M68G01
 02-030,75-31-21
(1) RE 5/A
.  2623M90G01
 34-236,72-00-02
(1) Bracket
(SIN 61A13)
.  2434M89G01
 34-230,72-00-02
(1) RE 5/A
.  2623M90G01
 34-236,72-00-02
(1) Bracket
(SIN 61A13)
.  2561M37P01
 34-235,72-00-02
(1) RE 5/A
.  2623M91P01
 34-237,72-00-02
(1) Bracket
(SIN 61A13)
.  2434M89G01
 34-230,72-00-02
(1) RE 5/A
.  2623M75G01
 34-261,72-00-02
(1) Bracket, Machined
(SIN 99210)
.  332U8912-11
 34-260,72-00-02
(1) RE 5/A
.  2330M45G06
 33-025,72-00-02
(1) Combustor Nozzle
Assembly
(SIN 0010A)
.  2330M45G05
 33-024,72-00-02
(1) RW 5/A
.  2330M45G02
 33-023,72-00-02
(1) Combustor Nozzle
Assembly
(SIN 0010A)
.  2330M45G02
 33-023,72-00-02
(1) RW 5/A
.  2330M45G03
 33-022,72-00-02
(1) Combustor Nozzle
Assembly
(SIN 0010A)
.  2330M45G03
 33-022,72-00-02
(1) RW 5/A
..  2330M54G06
 01-095,72-40-00
(1) Combustor
Diffuser Assembly
(SIN 12000)
..  2330M54G05
 01-094,72-40-00
(1) RW 5/A
..  2330M54G02
 01-093,72-40-00
(1) Combustor
Diffuser Assembly
(SIN 12000)
..  2330M54G02
 01-093,72-40-00
(1) RW 5/A
..  2330M54G03
 01-092,72-40-00
(1) Combustor
Diffuser Assembly
(SIN 12000)
..  2330M54G03
 01-092,72-40-00
(1) RW 5/A
...  2623M71G01
 01-011,73-11-40
(1) Manifold, Top
Main Fuel
(SIN 34101)
...  2561M11G01
 01-010A,73-11-40
(1) RE 5/C
...  2619M58G01
 01-021,73-11-40
(1) Manifold, Lower
Fuel
(SIN 34102)
...  2561M12G01
 01-020A,73-11-40
(1) RE 5/C
...  2623M84P01
 01-202,73-11-30
(1) Bracket, Support
(SIN 34114)
...  2486M73P01
 01-201,73-11-30
(1) RE 5/A
...  2636M78G01
 01-273,73-11-30
(1) Bracket
(SIN 34118)
...  2486M74P01
 01-271,73-11-30
(1) RE 5/A
2330M20G01/
G02/G03/G04/
G05/G06/G07/
G08
(X) Assembly,
Propulsor Module
2330M20G01/
G02/G03/G04/
G05/G06/G07/
G08
(X) RM -/-
.  2620M81G01
 01-071,73-11-40
(6) Bracket, Support
(SIN 34110)
.  2343M87G01
 01-070,73-11-40
(6) RE 5/A
.  2623M81G01
 01-082,73-11-40
(2) Bracket, Support
(SIN 34112)
.  2475M24G01
 01-081,73-11-40
(2) RE 5/A

### Page 13

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
13 of 28
.  2623M81G01
 01-082,73-11-40
(2) Bracket, Support
(SIN 34112)
.  2365M49G01
 01-080,73-11-40
(2) RE 5/A
.  2623M82G01
 01-101,73-11-40
(1) Bracket, Support
(SIN 34117)
.  2381M41G01
 01-100,73-11-40
(1) RE 5/A
.  2620M93P01
 01-131,73-11-40
(10) Slider, Spring
(SIN 34191)
.  2429M18P01
 01-130,73-11-40
(10) RE 5/A
.  2623M83P01
 01-151,73-11-40
(10) Dampener
(SIN 34192)
.  2429M19P01
 01-150,73-11-40
(10) RE 5/A
.  2613M58P01
 05-061,79-21-00
(1) Bracket, Support
(SIN 40A10)
.  2426M81P01
 05-060,79-21-00
(1) RE 5/A
.  2613M59G01
 05-091,79-21-00
(1) Bracket, Support
(SIN 40A1B)
.  2363M29G01
 05-090,79-21-00
(1) RE 5/A
.  2623M87G01
 34-241,72-00-02
(1) Bracket, Stage
4/7 Stub Assembly
(SIN 61113)
.  2404M74G01
 34-240,72-00-02
(1) RE 5/A
.  2623M89G01
 01-031,75-31-21
(1) Bracket, Support
(SIN 61A12)
.  2404M37G01
 01-030,75-31-21
(1) RE 5/A
.  2623M90G01
 34-236,72-00-02
(1) Bracket
(SIN 61A13)
.  2434M89G01
 34-230,72-00-02
(1) RE 5/A
.  2623M75G01
 34-261,72-00-02
(1) Bracket, Machined
(SIN 99210)
.  332U8912-11
 34-260 ,72-00-02
(1) RE 5/A
. /2330M45G01
G04
 33-020,72-00-02
 33-021,72-00-02
(1) Combustor Nozzle
Assembly
(SIN 0010A)
. /2330M45G01
G04
 33-020,72-00-02
 33-021,72-00-02
(1) RM -/-
.. /2330M54G01
G02/G03/G04
 01-090,72-40-00
 01-091,72-40-00
 01-092,72-40-00
 01-093,72-40-00
(1) Combustor
Diffuser Assembly
(SIN 12000)
.. /2330M54G01
G02/G03/G04
 01-090,72-40-00
 01-091,72-40-00
 01-092,72-40-00
 01-093,72-40-00
(1) RM -/-
...  2623M71G01
 01-011,73-11-40
(1) Manifold, Top
Main Fuel
(SIN 34101)
...  2561M11G01
 01-010A,73-11-40
(1) RE 5/C
...  2623M71G01
 01-011,73-11-40
(1) Manifold, Top
Main Fuel
(SIN 34101)
...  2419M11G01
 01-010,73-11-40
(ALT) RE 5/A
...  2623M71G01
 01-011,73-11-40
(1) Manifold, Top
Main Fuel
(SIN 34101)
...  2546M11G01
 01-010B,73-11-40
(ALT) RE 5/A
...  2619M58G01
 01-021,73-11-40
(1) Manifold, Lower
Fuel
(SIN 34102)
...  2561M12G01
 01-020A,73-11-40
(1) RE 5/C
...  2619M58G01
 01-021,73-11-40
(1) Manifold, Lower
Fuel
(SIN 34102)
...  2419M12G01
 01-020,73-11-40
(ALT) RE 5/A
...  2619M58G01
 01-021,73-11-40
(1) Manifold, Lower
Fuel
(SIN 34102)
...  2546M12G01
 01-020B,73-11-40
(ALT) RE 5/C
...  2623M84P01
 01-202,73-11-30
(1) Bracket, Support
(SIN 34114)
...  2414M84G01
 01-200,73-11-40
(1) RE 5/A
...  2636M78G01
 01-273,73-11-30
(1) Bracket
(SIN 34118)
...  2432M67G01
 01-270,73-11-30
(1) RE 5/A
Operation Codes
RE=Replace
RM=Remains

### Page 14

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
14 of 28
RW=Rework
Change Codes
5=Qualified interchangeability. Refer to paragraph 1.K., 
.Interchangeability
Support Codes
A=Old parts will no longer be supplied.
C=Old parts will be supplied until December, 2017.
D. Parts Disposition
Use serviceable old parts for engines that have not changed.
E. Tooling - Price and Availability
Tool Number Description
9C1207G01 Cart Nitrogen Pressure Check (nitrogen cart) (optional)
NOTE:Filtered shop air with a pressure regulator and gauge
may be used as alternative to nitrogen cart.
11C4566G02 Set Adapter, Manifold Pressure Check (fuel adapter)
(optional)
SPL-7668 Hoist Equipment for Aft Mount and Thrust Link
Removal/Installation (Boeing tool)
9C1173G02 Fixture, Raise/Lower - Accessory Gearbox (AGB) Module
(raise/lower fixture), for use with propulsor or engine in
overhead gantry or aft fan pedestals 11C4251G05 and turbine
rear frame (TRF) pedestals 11C4251G01.
NOTE:Alternate tool to 11C4664, the 9C1173 cannot be used
with the engine in fan hub frame (FHF) pedestals
11C4251G02 mounted on the fan frame.
11C3262G03 Fixture, Install/Remove AGB Module (install/remove fixture)
NOTE:The 11C3262 is only compatible with the 9C1173.
11C4381G01 Bracket Set, Support/Lift AGB Module (bracket set)
11C4412G02 Fixture, Install/Remove - Line Replaceable Units (LRU) (LRU
fixture)
9446M93P01 Stand, Jack - LRU Install/Remove (jack stand)
11C4664P01 Fixture, Raise/Lower - AGB Module (raise/lower fixture)
preferred lift jack can be used with propulsor or engine in
pedestals including the FHF pedestals 11C4251G02.
NOTE:The 11C4664 raise/lower fixture tool is only compatible
with the install/remove fixture 9471M12.
9471M12P01 Fixture, Install/Remove AGB Module (install/remove fixture)
NOTE:The 9471M12 install/remove fixture is only compatible
with the raise/lower fixture 11C4664.
11C4251G01 Bracket Set, Support - Main Engine, TRF (TRF pedestals)
11C4251G02 Bracket Set, Support - Main Engine, FHF (FHF pedestals)
11C4251G05 Bracket Set, Support - Main Engine, Aft Fan Case (aft fan
pedestals)
NOTE:The 11C4251 pedestals are alternates to overhead rail
system for removing the lower manifold.
11C4300P02 Stand, Shipping - Engine/Propulsor
NOTE:Recommended shipping stand to gain access to perform
this Service Bulletin.
9429M44G01 Adapter, Overhead Support - FHF (FHF overhead support
adapter)
9429M47G01 Adapter, Overhead Support - Low Pressure Turbine (LPT) (LPT
overhead support adapter)
9429M48G01 Adapter, Overhead Support - Bridge Beam (bridge beam
overhead support adapter)

### Page 15

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
15 of 28
NOTE:Adapters overhead supports are optional to 11C4251
pedestals to remove lower manifold.
Local Purchase Customer Overhead Rail System (rail system)
NOTE:Overhead rail system is optional to 11C4251 pedestals
to remove the lower fuel manifold.
3. ACCOMPLISHMENT INSTRUCTIONS
A. General
(1) All soft life thresholds for modules and accessories may be exceeded during
quick turn (Q/T) repair. Refer to GEnx-2B CIR, 72-00-00, INSPECTION,
Subtask 72-00-00-220-005.
NOTE:This procedure provides instructions to replace the top and/or lower fuel
manifold assemblies in shop with minimum engine disassembly. The engine
rework for this Service Bulletin is considered to be a Q/T,
continued-time shop visit workscope. All removed hardware and modules
must be visually inspected for continued-time as defined for an assembled
engine workscope.
NOTE:No dimensional inspection or fluorescent-penetrant inspection (FPI) (i.e.
enhanced inspections) are required to complete this Service Bulletin,
including no FPI required for the fan frame thrust link clevises or
turbine rear frame (TRF) case, unless stated. For all visual findings,
refer to GEnx-2B CIR. Additional inspection criteria to the assembled
engine workscope visual inspection recommendations are in paragraph 
.3.C., Inspection
NOTE:Boeing engine build up (EBU) pneumatic ducts must be removed. If
pneumatic ducts are not removed, refer to the Boeing 747-8 AMM, 36-11-01,
TASK 36-11-01-000-801 to continue with the removal of the necessary
hardware.
B. Removal of the Fuel Manifolds
NOTE:For post-GEnx-2B S/B  engine configuration, refer to step 3.B.(2)73-0079
to remove the lower fuel manifold section only.
(1) Remove the top fuel manifold as follows:
NOTE:The top fuel manifold can be replaced in an engine stand, overhead gantry
system, or pedestals.
(a) Remove the thrust links and aft mount. Refer to Boeing 747-8 AMM, TASK
71-21-02-000-801-G00.
(b) For pre-GEnx-2B S/B , do the disassembly procedure that follows:72-0144
1 Remove the air manifold (20-011, 75-24-10) (SIN 61204) from the
turbine center frame (TCF) at 11:00 o'clock position. Refer to the
GEnx-2B EM, 72-00-02, DISASSEMBLY 003, CONFIG 01, Subtask
72-00-02-030-116.
2 Remove the air manifold (20-021, 75-24-10) (SIN 61203) from the TCF
at 11:00 o'clock position. Refer to the GEnx-2B EM, 72-00-02,
DISASSEMBLY 003, CONFIG 01, Subtask 72-00-02-030-116.
3 Remove the manifold (20-010, 75-24-30) (SIN 61103). Refer to GEnx-2B
EM, 72-00-02, DISASSEMBLY 003, Subtask 72-00-02-030-118.
4 Remove the manifold (20-041, 75-24-30) (SIN 61100). Refer to GEnx-2B
EM, 72-00-02, DISASSEMBLY 003, Subtask 72-00-02-030-236.
5 Remove the support bracket (01-191, 73-11-30) (SIN 34113) from the
No. 4 fuel nozzle.
6 Remove the two igniters (01-010A, 74-21-20) (SIN 66200) from the
combustor case (01-080, 72-41-00) (SIN 12001). Refer to the GEnx-2B
EM, 72-00-02, DISASSEMBLY 002, Subtask 72-00-02-030-183.
7 Remove the diffuser assembly (01-060, 75-31-21) (SIN 61A03), bowl
assembly (01-050) (SIN 61A02), start bleed valve (SBV) exit air duct
(01-010) (SIN 61A01), and SBV (01-010, 75-31-11) (SIN 60700). Refer
to the GEnx-2B EM, 72-00-02, DISASSEMBLY 002, Subtask
72-00-02-030-273.
8 Remove the transient bleed support tube (02-070, 75-31-21) (SIN
61A18). Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 002, CONFIG
02, Subtask 72-00-02-030-355.

### Page 16

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
16 of 28
9 Remove the duct (10-010, 75-24-30) (SIN 62103). Refer to the GEnx-2B
EM, 72-00-02, DISASSEMBLY 002, Subtask 72-00-02-030-197.
10 Remove the oil tube (05-011, 79-22-30) (SIN 46100). Refer to the
GEnx-2B EM, 72-00-02, DISASSEMBLY 003, Subtask 72-00-02-030-117.
11 Remove the air manifold (05-082, 79-22-30) (SIN 46101) from the top
of the engine. Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 003,
CONFIG 01, Subtask 72-00-02-030-119.
12 Remove the stage 4 manifold (20-010, 75-24-10) (SIN 61204). Refer to
the GEnx-2B EM, 72-00-02, DISASSEMBLY 003, Subtask 72-00-02-030-116.
13 Remove the bracket (01-271, 73-11-30) (SIN 34118) from the No. 5
fuel nozzle on the upper right side of the engine.
14 Remove the support bracket (01-130, 73-11-30) (SIN 34116) from the
fuel nozzle No. 6 as follows:
a Remove the machine bolts (01-040) (SIN 12520), then remove the
support racket (01-130) (SIN 34116). Retain parts for future
use.
15 Remove the top main fuel manifold (01-010, 73-11-40) (SIN 34101).
Refer to the GEnx-2B EM, 72-41-00, DISASSEMBLY 001, CONFIG 01,
Subtask 72-41-00-040-027.
16 Remove the spring (01-140, 73-11-40) (SIN 34190), spring slider
(01-130) (SIN 34191), dampener (01-150) (SIN 34192), and machine
bolt (01-120) (SIN 34124), at five locations from the fuel manifold
(01-010, 73-11-40) (SIN 34101) and retain for future use.
17 Remove the drain plugs (01-170) (SIN 34160) from the removed top
fuel manifold (01-010) (SIN 34101).
(c) For post-GEnx-2B S/B , do the disassembly procedure that72-0144
follows:
1 Remove the air bracket (20-340, 75-24-10) (SIN 61816) from the top
of the engine. Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 003,
CONFIG 02, Subtask 72-00-02-030-429.
2 Remove the air bracket (20-330, 75-24-10) (SIN 61810) from the top
of the engine. Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 003,
CONFIG 02, Subtask 72-00-02-030-429.
3 Remove the air manifold (20-011, 75-24-10) (SIN 61204) from the TCF
at 11:00 o'clock position. Refer to the GEnx-2B EM, 72-00-02,
DISASSEMBLY 003, CONFIG 02, Subtask 72-00-02-030-429.
4 Remove the air manifold (20-021, 75-24-10) (SIN 61203) from the TCF
at 11:00 o'clock position. Refer to the GEnx-2B EM, 72-00-02,
DISASSEMBLY 003, CONFIG 02, Subtask 72-00-02-030-429.
5 Remove the transient bleed valve (01-040, 75-31-11) (SIN 60800).
Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 003, CONFIG 02,
Subtask 72-00-02-030-429.
6 Remove the air bracket (33-720, 72-00-02) (SIN 61513) from the
compressor aft extension case pad. Refer to the GEnx-2B EM,
72-00-02, DISASSEMBLY 003, CONFIG 02, Subtask 72-00-02-030-453.
7 Remove the air manifold (20-011, 75-24-30) (SIN 61103) at the 10:30
to 12:00 o'clock position area. Refer to the GEnx-2B EM, 72-00-02,
DISASSEMBLY 003, CONFIG 02, Subtask 72-00-02-030-433.
8 Remove the manifold (20-042, 75-24-30) (SIN 61100) at the 1:30 to
3:00 o'clock position area. Refer to the GEnx-2B EM, 72-00-02,
DISASSEMBLY 003, CONFIG 02, Subtask 72-00-02-030-436.
9 Remove the vent tube (05-012, 79-22-30) (SIN 46100) from the top of
the engine. Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 003,
CONFIG 02, Subtask 72-00-02-030-430.
10 Remove the air manifold (05-082, 79-22-30) (SIN 46101) from the top
of the engine. Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 003,
CONFIG 02, Subtask 72-00-02-030-437.
11 Remove the bracket (01-271, 73-11-30) (SIN 34118) from the right
side of the engine. Refer to the GEnx-2B EM, 72-41-00, DISASSEMBLY
001, CONFIG 02, Subtask 72-41-00-040-058.
12 Remove the support bracket (01-130, 73-11-30) (SIN 34116) from the

### Page 17

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
17 of 28
fuel nozzle No. 6 as follows:
a Remove the machine bolts (01-040) (SIN 12520), then remove the
support bracket (01-130) (SIN 34116). Retain parts for future
use.
13 Remove the duct (10-020, 75-24-30) (SIN 62108). Refer to the GEnx-2B
EM, 72-00-02, DISASSEMBLY 002, CONFIG 02, Subtask 72-00-02-030-371.
14 Remove the eight machine bolts (02-150 and 02-170, 75-31-21) (SIN
61A21 and SIN 61A23) to remove the bulb seal (02-231, 75-31-21) (SIN
61A50) and the transient bleed air tube (02-060) (SIN 61A03). Refer
to the GEnx-2B EM, 72-00-02, DISASSEMBLY 002, CONFIG 02, Subtask
72-00-02-030-351 and Substask 72-00-02-030-353.
15 Remove the support bracket (02-030, 75-31-21) (SIN 61A12) and
transient bleed air tube (02-010) (SIN 61A01). Refer to the GEnx-2B
EM, 72-00-02, DISASSEMBLY 002, CONFIG 02, Subtask 72-00-02-030-355.
16 Remove the main igniter cooling shrouds (01-120, 74-21-10) (SIN
66202) from both upper and lower igniters. Refer to the GEnx-2B EM,
72-00-02, DISASSEMBLY 002, CONFIG 02, Subtask 72-00-02-030-346.
17 Remove the igniters (01-010, 74-21-20) (SIN 66200) from the engine
and tie back the ignition cables (01-010, 74-21-10) (SIN 69100) out
of the way. Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 002,
CONFIG 02, Subtask 72-00-02-030-343.
18 Remove the SBV (01-010, 75-31-11) (SIN 60700) from the left side of
the engine. Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 002,
CONFIG 02, Subtask 72-00-02-030-359.
19 Remove the support bracket (01-191, 73-11-30) (SIN 34113) from the
left side of the engine. Refer to the GEnx-2B EM, 72-40-00, ASSEMBLY
001, CONFIG 02, Subtask 72-40-00-440-067, Figure 1020 (Sheet 10).
20 Remove the top main fuel manifold (01-010, 73-11-40) (SIN 34101).
Refer to the GEnx-2B EM, 72-41-00, DISASSEMBLY 001, CONFIG 01,
Subtask 72-41-00-040-025.
21 Install protective covers/plugs on all open apertures.
(2) Remove the lower fuel manifold as follows:
NOTE:If an engine stand is planned to be used, we recommend to use 11C4300
shipping stand. However, it is recommended to be performed in an overhaul
rail system or in pedestals. Pedestal usage is also unique to tool
availability due to alternate tooling availability. Refer to paragraph 
 for tool alternate usage.2.E., Tooling - Price and Availability
(a) Remove AGB heat shield panels (40-020, 72-00-02) (SIN 29901), (40-030)
(SIN 29902), (40-040) (SIN 29903), (40-050) (SIN 29904), (40-060) (SIN
29905), and (40-070) (SIN 29906). Refer to the GEnx-2B EM, 72-00-02,
DISASSEMBLY 002, Subtask 72-00-02-030-227.
(b) Remove the bracket (01-195, 73-11-30) (SIN 34119) at No. 5 fuel nozzle
location as follows:
1 Remove the machine bolt (01-260) (SIN 34122), machine bolt (01-040)
(SIN 12520), two cushioned loop clamps (01-060A, 73-11-40) (SIN
3418K), and two machine bolts (01-050A, 73-11-40) (SIN 3412L), then
remove bracket (01-195) (SIN 34119). Retain parts for future use.
(c) Remove the bracket (01-270, 75-42-10) (SIN 3411B) at No. 6 fuel nozzle
location as follows:
1 Remove the machine bolt (01-260) (SIN 65C21), then remove bracket
(01-270) (SIN 3411B). Retain parts for future use.
(d) Remove the support bracket (01-250, 72-54-00) (SIN 61116) that supports
the 7th stage manifold (20-031, 75-24-30) (SIN 61101) as follows:
1 Remove the machine bolt (01-020, 72-54-00) (SIN 92525) and machine
bolt (01-030) (SIN 61125), then remove support bracket (01-250) (SIN
61116). Retain parts for future use.
(e) Remove the support bracket (01-201, 73-11-30) (SIN 34114) at No. 15
fuel nozzle location as follows:
1 Remove the machine bolt (01-260) (SIN 34122) and machine bolt
(01-040) (SIN 12520), then remove bracket (01-201) (SIN 34114).
Retain parts for future use.

### Page 18

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
18 of 28
(f) Remove the bracket (01-030, 75-31-21) (SIN 61A12). Refer to Figure 1
and do as follows:
1 Remove the machine bolts (01-020) (SIN 61A20), then remove bracket
(01-030) (SIN 61A12). Retain the machine bolts (01-020) (SIN 61A20)
for future use.
(g) Remove the bracket (20-220, 75-24-10) (SIN 61216) that supports the 4th
stage air tube (20-051) (SIN 61200) as follows:
1 Remove the machine bolts (20-171) (SIN 61223) and shear bolts
(01-060, 72-41-00) (SIN 12024), then remove bracket (20-220) (SIN
61216). Retain parts for future use.
(h) Deleted.
(i) Deleted.
(j) Deleted.
(k) Deleted.
(l) Deleted.
(m) Remove the stage 4 manifold (20-010, 75-24-10) (SIN 61204) at the 8:00
o'clock position. Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 003,
Subtask 72-00-02-030-267.
(n) Remove the stage 4 manifold (20-010, 75-24-10) (SIN 61204) at the 5:00
to 7:00 o'clock position. Refer to the GEnx-2B EM, 72-00-02,
DISASSEMBLY 003, Subtask 72-00-02-030-114.
(o) Remove the stage 4 manifold (20-010, 75-24-10) (SIN 61204) at the 2:00
to 4:30 o'clock position. Refer to the GEnx-2B EM, 72-00-02,
DISASSEMBLY 003, Subtask 72-00-02-030-115.
(p) Remove the manifold (20-021, 75-24-30) (SIN 61102) at the 7:30 to 9:00
o'clock position. Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY 003,
CONFIG 01, Subtask 72-00-02-030-522.
(q) Remove the air manifold (20-030, 75-24-30) (SIN 61101) at the 4:30 to
7:00 o'clock position. Refer to the GEnx-2B EM, 72-00-02, DISASSEMBLY
003, CONFIG 01, Subtask 72-00-02-030-523.
(r) Loosen and if necessary, remove the lower half high pressure turbine
(HPT) active clearance control (ACC) manifold retaining bolts (15-170,
75-24-30) (SIN 62126) to let the manifolds move to give access to the
CDN to HPT case flange bolts. Refer to the GEnx-2B EM, 72-50-00,
DISASSEMBLY 001, Subtask 72-50-00-030-035.
(s) Loosen the lower half fuel manifold retaining bracket securing nuts
(34-110, 72-00-02) (SIN 17440) attached to the CDN/HPT flange. Refer to
the GEnx-2B EM, 72-50-00, DISASSEMBLY 001, Subtask 72-50-00-030-016,
Figure 520 (Sheet 1).
NOTE:Some fuel nozzles can cause interference with the removal of the fuel
manifold. To facilitate the removal, continue with the fuel nozzle
removal that causes interference with the manifold. Refer to the
GEnx-2B EM, 72-41-00, DISASSEMBLY 001, CONFIG 02, Subtask
72-41-00-040-034.
(t) Remove the lower fuel manifold (01-020, 73-11-40) (SIN 34102). Refer to
the GEnx-2B EM, 72-41-00, DISASSEMBLY 001, Subtask 72-41-00-040-025.
(u) Install protective covers/plugs on all open apertures.
(v) Remove the fuel manifold aft support sliding mounts (assembly) at each
of the 10 fuel manifold support locations as follows:
1 Remove the machine bolt (01-120, 73-11-40) (SIN 34124) to permit
disassembly of the spring sliders (01-130) (SIN 34191), dampeners
(01-150) (SIN 34192), and springs (01-140) (SIN 34190). Discard the
spring sliders (01-130) (SIN 34191), dampeners (01-150) (SIN 34192),
and springs (01-140) (SIN 34190) and retain the machine bolts
(01-120, 73-11-40) for future use.
(w) Remove the bracket (05-090, 79-21-00) (SIN 40A1B). Refer to Figure 1
and do as follows:
1 Remove the three machine bolts (05-040) (SIN 40A22) that secure
bracket (05-090) (SIN 40A1B) to the bracket (34-240, 72-00-02) (SIN

### Page 19

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
19 of 28
61113) and remove bracket (05-090) (SIN 40A1B). Discard bracket and
retain the three machine bolts for future use. Refer to the GEnx-2B
EM, 72-00-02, DISASSEMBLY 002, CONFIG 02, Subtask 72-00-02-030-341.
(x) Remove the bracket (05-060, 79-21-00) (SIN 40A10) from the CDN/HPT
flange. Refer to  and do as follows:Figure 1
1 Remove the two self-locking nuts (34-110, 72-00-02) (SIN 17440) and
two machine bolts (05-040, 79-21-00) (SIN 40A22), then remove
bracket (05-090) (SIN 40A10). Discard the bracket and two
self-locking nuts (34-110, 72-00-02) (SIN 17440) and retain the two
machine bolts (05-040, 79-21-00) (SIN 40A22) for future use.
(y) Remove the bracket (34-240, 72-00-02) (SIN 61113) from the CDN/HPT
flange. Refer to  and do as follows:Figure 1
1 Remove the seven self-locking nuts (34-110) (SIN 17440) that connect
the bracket (34-240) (SIN 61113) to the CDN/HPT flange, then remove
the bracket (34-240) (SIN 61113). Discard the bracket (34-240) (SIN
61113) and the self-locking nuts (34-110) (SIN 17440).
(z) For pre-GEnx-2B S/B  or post-GEnx-2B S/B  and72-0144 72-0144
post-GEnx-2B S/B , do as follows:75-0015
1 Remove the bracket (34-230, 72-00-02) (SIN 61A13) from the CDN/HPT
flange. Refer to  and do as follows:Figure 1
a Remove the four self-locking nuts (34-110) (SIN 17440) that
connect the bracket (34-230) (SIN 61A13) to the CDN/HPT flange,
then remove bracket (34-230) (SIN 61A13). Discard the bracket
(34-230) (SIN 61A13) and self-locking nuts (34-110) (SIN 17440).
(aa)For post-GEnx-2B S/B  and pre-GEnx-2B S/B , do as72-0144 75-0015
follows:
1 Remove the bracket (34-235, 72-00-02) (SIN 61A13) from the CDN/HPT
flange. Refer to  and do as follows:Figure 1
a Replace the five self-locking nuts (34-110) (SIN 17440) that
connect the bracket (34-235) (SIN 61A13) to the CDN/HPT flange,
then remove bracket (34-235) (SIN 61A13). Discard bracket
(34-235) (SIN 61A13) and self-locking nuts (34-110) (SIN 17440).
(ab)Remove the fuel manifold support brackets from the CDN/HPT flange.
Refer to  and do as follows:Figure 1
1 Remove the six fuel manifold brackets (01-070, 73-11-40) (SIN
34110), two support brackets (01-081) (SIN 34112), bracket (01-100)
(SIN 34117), and bracket (34-260, 72-00-02) (SIN 99210) and do as
follows:
a As necessary to get access to the self-locking nuts (34-110)
(SIN 17440), remove the HPT air manifolds (15-010, 75-24-30)
(SIN 6210A), (15-020) (SIN 6210B), (15-030) (SIN 6210C),
(15-040) (SIN 6210D), (15-050) (SIN 6210E), (15-060) (SIN
6210F), (15-070) (SIN 6210G), and (15-080) (SIN 6210H) from the
HPT case (01-490, 72-52-00) (SIN 174B0). Refer to the GEnx-2B
EM, 72-50-00, DISASSEMBLY 001, Subtask 72-50-00-030-035.
2 At each location in step 3.B.(2)(ab) , remove the self-locking nuts1
(34-110) (SIN 17440) as necessary to remove all 10 brackets. Refer
to .Figure 1
3 Discard the 10 brackets and self-locking nuts (34-110) (SIN 17440).
NOTE:Do not remove all the flange self-locking nuts (34-110) (SIN
17440), only those necessary to remove the brackets listed.
C. Inspection
NOTE:All removed hardware and modules must be visually inspected for continued
time as specified for an assembled engine workscope. Refer to the GEnx-2B
CIR, 72-00-00, INSPECTION 001. No dimensional inspection or an FPI (i.e.
enhanced inspections) are necessary to complete this Service Bulletin
unless stated differently.
(1) Do a general visual inspection (GVI) of all parts that are removed. Refer
to the GEnx-2B CIR, 72-00-00, INSPECTION 001, Subtask 72-00-00-220-009.
(2) Do a GVI of all parts that were not removed but are exposed because of

### Page 20

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
20 of 28
removal of other engine parts. Refer to the GEnx-2B CIR, 72-00-00,
INSPECTION 001, Subtask 72-00-00-220-009.
D. Installation of the New Fuel Manifold System
NOTE:For post-GEnx-2B S/B  engine configuration, refer to step 3.D.(22)73-0079
to install the lower fuel manifold section only.
(1) Install the new ten fuel manifold support brackets on the CDN/HPT flange.
Refer to  and do as follows:Figure 2
(a) Install the six new fuel manifold brackets (01-071, 73-11-40) (SIN
34110), two new support brackets (01-082) (SIN 34112), new bracket
(01-101) (SIN 34117), and new bracket (34-261, 72-00-02) (SIN 99210).
(b) At each location, install new self-locking nuts (34-110) (SIN 17440)
and hand-tighten to attach the 10 brackets firmly to the CDN/HPT
flange. Refer to .Figure 2
(c) Torque the self-locking nuts (34-110) to 276 to 324 lb in. (31.1 to
36.6 Nm). Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY 001, Subtask
72-50-00-430-042.
(2) As necessary, reinstall the removed fuel nozzles. Refer to the GEnx-2B EM,
72-40-00, ASSEMBLY 001, CONFIG 02, Subtask 72-40-00-440-051.
(3) Install the new upper fuel manifold section on the engine. Refer to Figure
 and do as follows:2
(a) Install the plugs (01-170) (SIN 34160) to the new top fuel manifold
(01-011) (SIN 34101) and lower fuel manifold (01-021) (SIN 34102).
Refer to the GEnx-2B EM, 72-40-00, ASSEMBLY 001, Subtask
72-40-00-440-023.
(b) Put the new top fuel manifold (01-011, 73-11-40) (SIN 34101) and new
lower fuel manifold (01-021) (SIN 34102) on the engine so that the
mount pads are adjacent to the support brackets. Loosely install the
fuel manifold pigtails on the fuel nozzle at each of the 44 locations,
two at each fuel nozzle. Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY
001, Subtask 72-50-00-220-005.
(4) For pre-GEnx-2B S/B , do the steps that follow:72-0144
(a) Install the new bracket (34-236, 72-00-02) (SIN 61A13) on the CDN/HPT
flange. Refer to  and do as follows:Figure 2
1 Install the three new-self locking nuts (34-110) (SIN 17440) and
hand-tighten to attach the bracket (34-236) (SIN 61A13) firmly to
the CDN/HPT flange.
2 Torque the self-locking nuts (34-110) (SIN 17440) to 276 to 324 lb
in. (31.1 to 36.6 Nm). Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY
001, Subtask 72-50-00-430-042.
(5) For post-GEnx-2B S/B  and pre-GEnx-2B S/B , do the steps that72-0144 75-0015
follow:
(a) Install the new bracket (34-237, 72-00-02) (SIN 61A13) on the CDN/HPT
flange. Refer to  and do as follows:Figure 2
1 Install the five new self-locking nuts (34-110) (SIN 17440) and
hand-tighten to attach the bracket (34-237) (SIN 61A13) firmly to
the CDN/HPT flange.
2 Torque the self-locking nuts (34-110) (SIN 17440) to 276 to 324 lb
in. (31.1 to 36.6 Nm). Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY
001, Subtask 72-50-00-430-042.
(6) For post-GEnx-2B S/B  and post-GEnx-2B S/B , do the steps72-0144 75-0015
that follow:
(a) Install the new bracket (34-236, 72-00-02) (SIN 61A13) on the CDN/HPT
flange. Refer to  and do as follows:Figure 2
1 Install the three new self-locking nuts (34-110) (SIN 17440) and
hand-tighten to attach the bracket (34-236) (SIN 61A13) firmly to
the CDN/HPT flange.
2 Torque the self-locking nuts (34-110) (SIN 17440) to 276 to 324 lb
in. (31.1 to 36.6 Nm). Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY
001, Subtask 72-50-00-430-042.
(7) For pre-GEnx-2B S/B , do the steps that follow:72-0144

### Page 21

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
21 of 28
(a) Install the new bracket (01-031, 75-31-21) (SIN 61A12) to new bracket
(34-236, 72-00-02) (SIN 61A13). Refer to  and do as follows:Figure 2
1 Install the two existing machine bolts (01-020, 75-31-21) (SIN
61A20). Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 005, CONFIG 02,
Subtask 72-00-02-440-500 and final torque. Refer to the GEnx-2B EM,
72-00-02, ASSEMBLY 005, CONFIG 02, Subtask 72-00-02-440-501.
(8) For post-GEnx S/B  and pre or post-GEnx-2B S/B , do the steps72-0144 75-0015
that follow:
(a) Install the new bracket (02-031, 75-31-21) (SIN 61A12) to the new
bracket (34-236, 72-00-02) (SIN 61A13). Refer to  and do asFigure 2
follows:
1 Install the two existing machine bolts (01-020, 75-31-21) (SIN
61A20). Refer to the GEnx-2B, 72-00-02, ASSEMBLY 005, CONFIG 02,
Subtask 72-00-02-440-500 and final torque. Refer to the GEnx-2B,
72-00-02, ASSEMBLY 005, CONFIG 02, Subtask 72-00-02-440-501.
(9) Install the new bracket (34-241, 72-00-02) (SIN 61113) on the CDN/HPT
flange. Refer to  and do as follows:Figure 2
(a) Install seven new self-locking nuts (34-110) (SIN 17440) and
hand-tighten to attach the bracket (34-241) (SIN 61113) firmly to the
CDN/HPT flange.
(b) Torque the self-locking nuts (34-110) (SIN 17440) to 276 to 324 lb in.
(31.1 to 36.6 Nm). Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY 001,
Subtask 72-50-00-430-042.
(10)Install the new bracket (05-061, 79-21-00) (SIN 40A10) on the CDN/HPT
flange. Refer to  and do as follows:Figure 2
(a) Install two new self-locking nuts (34-110, 72-00-02) (SIN 17440) and
hand-tighten to attach the bracket (05-061, 79-21-00) (SIN 40A10)
firmly to the CDN/HPT flange.
(b) Install two existing machine bolts (05-040) (SIN 40A22) to bracket
(34-240, 72-00-02) (SIN 61113) and hand-tighten.
(c) Torque the self-locking nuts (34-110) (SIN 17440) to 276 to 324 lb in.
(31.1 to 36.6 Nm). Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY 001,
Subtask 72-50-00-430-042.
(d) Torque the machine bolts (05-040, 79-21-00) (SIN 40A22) to 106 to 124
lb in. (11.9 to 14.0 Nm). Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY
005, CONFIG 02, Subtask 72-00-02-440-518.
(11)Final torque all new installed self-locking nuts (34-110, 72-00-02) (SIN
17440) that attach the new brackets to the CDN/HPT flange in a criss cross
pattern to a final torque of 368 to 432 lb in. (41.5 to 48.8 Nm). Refer to
the GEnx-2B EM, 72-50-00, ASSEMBLY 001, Subtask 72-50-00-430-042.
(12)As necessary, reinstall the HPT air manifolds (15-010, 75-24-30) (SIN
6210A), (15-020) (SIN 6210B), (15-030) (SIN 6210C), (15-040) (SIN 6210D),
(15-050) (SIN 6210E), (15-060) (SIN 6210F), (15-070) (SIN 6210G), and
(15-080) (SIN 6210H) on the HPT case (01-490, 72-52-00) (SIN 174B0). Refer
to the GEnx-2B EM, 72-50-00, ASSEMBLY 001, Subtask 72-50-00-430-028.
(13)Install the new bracket (05-091, 79-21-00) (SIN 40A1B). Refer to Figure 2
and do as follows:
(a) Install the three existing machine bolts (05-040) (SIN 40A22) and
hand-tighten to attach the bracket (05-091) (SIN 40A1B) to the new
bracket (34-241, 72-00-02) (SIN 61113) and torque to 106 to 124 lb in.
(11.9 to 14.0 Nm). Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 005,
CONFIG 02, Subtask 72-00-02-440-518.
(14)Install the new fuel manifold aft support sliding mounts (assembly) at
each of the 10 fuel manifold support locations. Refer to  and doFigure 2
as follows:
(a) Install the existing machine bolt (01-120, 73-11-40) (SIN 34124) on the
new spring slider (01-131) (SIN 34191), new dampener (01-151) (SIN
34192), and new spring (01-140) (SIN 34190). Refer to the GEnx-2B EM,
72-50-00, ASSEMBLY 001, Subtask 72-50-00-440-001.
(15)Install the new bracket (01-202, 73-11-30) (SIN 34114) at No. 15 fuel
nozzle location as follows:

### Page 22

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
22 of 28
(a) Install the existing machine bolt (01-260) (SIN 34122) and machine bolt
(01-040) (SIN 12520). Refer to the GEnx-2B EM, ASSEMBLY 001, CONFIG 02,
Subtask 72-40-00-440-067.
(16)Install the existing bracket (01-270, 75-42-10) (SIN 3411B) onto existing
bracket (01-210) (SIN 67216) with the machine bolt (01-260) (SIN 65C21) to
attach the bracket (01-270) (SIN 3411B) firmly. Refer to the GEnx-2B EM,
72-40-00, ASSEMBLY 001, CONFIG 02, Subtask 72-40-00-440-092.
(17)Install the existing support bracket (01-130, 73-11-30) (SIN 34116) onto
the fuel nozzle No. 6 using the machine bolts (01-040) (SIN 12520).
(18)Install the existing support bracket (01-250, 72-54-00) (SIN 61116) that
supports the air manifold (20-031, 75-24-30) (SIN 61101) as follows:
(a) Install the machine bolt (01-020, 72-54-00) (SIN 92525) and machine
bolt (01-030) (SIN 61125).
(19)Install the existing bracket (01-195, 73-11-30) (SIN 34119) at No. 5 fuel
nozzle location as follows:
(a) Install the machine bolt (01-260) (SIN 34122), machine bolt (01-040)
(SIN 12520), and two clamps (01-060A, 73-11-40) (SIN 3418K), and two
machine bolts (01-050A) (SIN 3412L) to attach the bracket (01-195,
73-11-30) (SIN 34119). Refer to the GEnx-2B EM, 72-40-00, ASSEMBLY 001,
CONFIG 02, Subtask 72-40-00-440-067 and Subtask 72-40-00-440-087.
(20)Install the existing bracket (20-220, 75-24-10) (SIN 61216) that supports
the 4th stage air tube (20-051) (SIN 61200) as follows:
(a) Install the machine bolts (20-171) (SIN 61223) and bolts (01-060,
72-41-00) (SIN 12024), then remove bracket (20-220, 75-24-10) (SIN
61216). Retain parts for future use.
(21)Install brackets and air manifolds as follows:
(a) For pre-GEnx-2B S/B , do the assembly procedure that follows:72-0144
1 Install the bracket (01-271, 73-11-30) (SIN 34118) on the upper
right side of No. 5 fuel nozzle location. Refer to GEnx-2B EM,
72-40-00, ASSEMBLY 001, CONFIG 01, Subtask 72-40-00-440-022.
2 Install the manifold (20-041, 75-24-30) (SIN 61100). Refer to the
GEnx-2B EM, 72-00-02, ASSEMBLY 004, Subtask 72-00-02-440-263.
3 Install the manifold (20-010, 75-24-30) (SIN 61103). Refer to the
GEnx-2B EM, 72-00-02, ASSEMBLY 004, Subtask 72-00-02-440-230.
4 Install the stage 4 manifold (20-010, 75-24-10) (SIN 61204). Refer
to the GEnx-2B EM, 72-00-02, ASSEMBLY 004, Subtask 72-00-02-440-129.
5 Install the support bracket (01-191, 73-11-30) (SIN 34113) to the
No. 4 fuel nozzle. Refer to the GEnx-2B EM, 72-40-00, ASSEMBLY 001,
Subtask 72-40-00-440-022.
6 Install the oil tube (05-011, 79-22-30) (SIN 46100). Refer to the
GEnx-2B EM, 72-00-02, ASSEMBLY 004, Subtask 72-00-02-440-122 and
Subtask 72-00-02-440-123.
7 Install the duct (10-010, 75-24-30) (SIN 62103). Refer to the
GEnx-2B EM, 72-00-02, ASSEMBLY 005, Subtask 72-00-02-440-184.
8 Install the transient bleed support tube (01-070, 75-31-21) (SIN
61A18). Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 005, CONFIG 02,
Subtask 72-00-02-440-501.
9 Install the diffuser assembly (01-060) (SIN 61A03) bowl assembly
(01-050) (SIN 61A02), air SBV exit duct (01-010) (SIN 61A01), and
start bleed valve (01-010, 75-31-11) (SIN 60700). Refer to GEnx-2B
EM, 72-00-02, ASSEMBLY 005, CONFIG 02, Subtasks 72-00-02-440-471,
72-00-02-440-500, and 72-00-02-440-504.
10 Install the two igniters (01-010A, 74-21-20) (SIN 66200) and connect
the cables. Refer to GEnx-2B EM, 72-00-02, ASSEMBLY 004, Subtask
72-00-02-440-005.
11 Install the thrust links and aft mount. Refer to the GEnx-2B, Boeing
747-8 AMM, 71-21-02, REMOVAL/INSTALLATION, TASK
71-21-02-400-801-G00.
(b) For post-GEnx-2B S/B  do the assembly procedure that follows:72-0144
1 Install the support bracket (01-191, 73-11-30) (SIN 34113) on the
left side of the engine on top of the No. 17 fuel nozzle. Refer to

### Page 23

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
23 of 28
the GEnx-2B EM, 72-40-00, ASSEMBLY 001, CONFIG 02, Subtask
72-40-00-640-005.
2 Install the SBV (01-010, 75-31-11) (SIN 60700) on the left side of
the engine. Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 004, CONFIG
02, Subtask 72-00-02-440-608.
3 Install the igniters (01-010, 74-21-20) (SIN 66200) and ignition
cables (01-010, 74-21-10) (SIN 69100) on the engine. Refer to the
GEnx-2B EM, 72-00-02, ASSEMBLY 005, CONFIG 02, Subtask
72-00-02-440-508.
4 Install the main igniter cooling shrouds (01-120, 74-21-10) (SIN
66202) on both upper and lower igniters. Refer to the GEnx-2B EM,
72-00-02, ASSEMBLY 005, CONFIG 02, Subtask 72-00-02-440-515.
5 Install the duct (10-020, 75-24-30) (SIN 62108). Refer to the
GEnx-2B EM, 72-00-02, ASSEMBLY 005, CONFIG 02, Subtask
72-00-02-440-475.
6 Install the support bracket (02-030, 75-31-21) (SIN 61A12) and
transient bleed air tube (02-010) (SIN 61A01). Refer to the GEnx-2B
EM, 72-00-02, ASSEMBLY 005, CONFIG 02, Subtask 72-00-02-440-499.
7 Install the eight machine bolts (02-150 and 02-170, 75-31-21) (SIN
61A21 and SIN 61A23) to tighten the transient bleed air duct
(02-060) (SIN 61A03). Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY
005, CONFIG 02, Subtask 72-00-02-440-504.
8 Install the bracket (01-271, 73-11-30) (SIN 34118) on the right side
of the engine on top of the No. 5 fuel nozzle. Refer to the GEnx-2B
EM, 72-40-00, ASSEMBLY 001, CONFIG 02, Subtask 72-40-00-440-067.
9 Install the air manifold (05-082, 79-22-30) (SIN 46101) at the top
of the engine. Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 004,
CONFIG 02, Subtask 72-00-02-440-669.
10 Install the vent tube (05-012, 79-22-30) (SIN 46100) at the top of
the engine. Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 004, CONFIG
02, Subtask 72-00-02-440-685.
11 Install the manifold (20-042, 75-24-30) (SIN 61100) at the 1:30 to
3:00 o'clock position area. Refer to the GEnx-2B EM, 72-00-02,
ASSEMBLY 004, CONFIG 02, Subtask 72-00-02-440-673.
12 Install the air manifold (20-011, 75-24-30) (SIN 61103) at the 10:30
to 12:00 o'clock position area. Refer to the GEnx-2B EM, 72-00-02,
ASSEMBLY 004, CONFIG 02, Subtask 72-00-02-440-609.
13 Install the air bracket (33-720, 72-00-02) (SIN 61513) on the
compressor aft extension case pad. Refer to the GEnx-2B EM,
72-00-02, ASSEMBLY 004, CONFIG 02, Subtask 72-00-02-440-609.
14 Install the transient bleed valve (01-040, 75-31-11) (SIN 60800).
Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 004, CONFIG 02, Subtask
72-00-02-440-608.
15 Install the air manifold (20-021, 75-24-10) (SIN 61203) at the TCF
at 11:00 o'clock position. Refer to the GEnx-2B EM, 72-00-02,
ASSEMBLY 004, CONFIG 02, Subtask 72-00-02-440-694.
16 Install the air manifold (20-011, 75-24-10) (SIN 61204) at the TCF
at 11:00 o'clock position. Refer to the GEnx-2B EM, 72-00-02,
ASSEMBLY 004, CONFIG 02, Subtask 72-00-02-440-695.
17 Install the air bracket (20-330, 75-24-10) (SIN 61810) at the top of
the engine. Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 004, CONFIG
02, Subtask 72-00-02-440-696.
18 Install the air bracket (20-340, 75-24-10) (SIN 61816) at the top of
the engine. Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 004, CONFIG
02, Subtask 72-00-02-440-696.
(22)Install the new lower fuel manifold configuration as follows:
(a) Install the three new fuel manifold support brackets on the CDN/HPT
flange. Refer to  and do as follows:Figure 2
1 Install the three new fuel manifold brackets (01-071, 73-11-40) (SIN
34110), new support brackets (01-082) (SIN 34112), and new bracket
(01-101) (SIN 34117).

### Page 24

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
24 of 28
2 At each location, install new self-locking nuts (34-110, 72-00-02)
(SIN 17440) and hand-tighten to attach the five brackets firmly to
the CDN/HPT flange. Refer to .Figure 2
3 Torque the self-locking nuts (34-110) to 276 to 324 lb in. (31.1 to
36.6 Nm). Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY 001, Subtask
72-50-00-430-042.
(b) As necessary, install the removed fuel nozzles back. Refer to the
GEnx-2B EM, 72-40-00, ASSEMBLY 001, CONFIG 02, Subtask
72-40-00-440-051.
(c) Install the lower fuel manifold on the engine. Refer to  andFigure 2
do as follows:
1 Put the new lower fuel manifold (01-021, 73-11-40) (SIN 34102) on
the engine to make sure that the mount pads are adjacent to the
support brackets. Loosely install the fuel manifold pigtails on the
fuel nozzle at each of the 22 locations, two at each fuel nozzle.
Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY 001, Subtask
72-50-00-220-005.
(d) Install the new bracket (34-241, 72-00-02) (SIN 61113) on the CDN/HPT
flange. Refer to  and do as follows:Figure 2
1 Install seven new self-locking nuts (34-110) (SIN 17440) and
hand-tighten to attach the bracket (34-241) (SIN 61113) firmly to
the CDN/HPT flange.
2 Torque the self-locking nuts (34-110) (SIN 17440) to 276 to 324 lb
in. (31.1 to 36.6 Nm). Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY
001, Subtask 72-50-00-430-042.
(e) Install the new bracket (05-061, 79-21-00) (SIN 40A10) on the CDN/HPT
flange. Refer to  and do as follows:Figure 2
1 Install two new self-locking nuts (34-110, 72-00-02) (SIN 17440) and
hand-tighten to attach the bracket (05-061, 79-21-00) (SIN 40A10)
firmly to the CDN/HPT flange.
2 Install the two existing machine bolts (05-040) (SIN 40A22) to the
bracket (34-240, 72-00-02) (SIN 61113) and hand-tighten.
3 Torque the self-locking nuts (34-110) (SIN 17440) to 276 to 324 lb
in. (31.1 to 36.6 Nm). Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY
001, Subtask 72-50-00-430-042.
4 Torque the machine bolts (05-040, 79-21-00) (SIN 40A22) to 106 to
124 lb in. (11.9 to 14.0 Nm). Refer to the GEnx-2B EM, 72-00-02,
ASSEMBLY 005, CONFIG 02, Subtask 72-00-02-440-518.
(f) Final torque all new installed self-locking nuts (34-110, 72-00-02)
(SIN 17440) that attach the new brackets to the CDN/HPT flange in a
criss-cross pattern to 368 to 432 lb in. (41.5 to 48.8 Nm). Refer to
the GEnx-2B EM, 72-50-00, ASSEMBLY 001, Subtask 72-50-00-430-042.
(g) As necessary, install the removed HPT air manifolds (15-010, 75-24-30)
(SIN 6210A), (15-020) (SIN 6210B), (15-030) (SIN 6210C), (15-040) (SIN
6210D), (15-050) (SIN 6210E), (15-060) (SIN 6210F), (15-070) (SIN
6210G), or (15-080) (SIN 6210H) on the HPT case (01-490, 72-52-00) (SIN
174B0) back. Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY 001, Subtask
72-50-00-430-028.
(h) Install the new bracket (05-091, 79-21-00) (SIN 40A1B). Refer to 
 and do as follows:Figure 2
1 Install the three existing machine bolts (05-040) (SIN 40A22) and
hand-tighten to attach the bracket (05-091) (SIN 40A1B) to the new
bracket (34-241, 72-00-02) (SIN 61113) and torque to 106 to 124 lb
in. (11.9 to 14.0 Nm). Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY
005, CONFIG 02, Subtask 72-00-02-440-518.
(i) Install the new fuel manifold aft support sliding mounts (assembly) at
each of the 10 fuel manifold support locations. Refer to  andFigure 2
do as follows:
1 Install the existing machine bolt (01-120, 73-11-40) (SIN 34124) on
the new spring slider (01-131) (SIN 34191), new dampener (01-151)
(SIN 34192), and new spring (01-140) (SIN 34190). Refer to the

### Page 25

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
25 of 28
GEnx-2B EM, 72-50-00, ASSEMBLY 001, Subtask 72-50-00-440-001.
(j) Install the new bracket (01-202, 73-11-30) (SIN 34114) at the No. 15
fuel nozzle location as follows:
1 Install the existing machine bolt (01-260) (SIN 34122) and machine
bolt (01-040) (SIN 12520). Refer to the GEnx-2B EM, ASSEMBLY 001,
CONFIG 02, Subtask 72-40-00-440-067.
(k) Install the existing support bracket (01-250, 72-54-00) (SIN 61116)
that supports the air manifold (20-031, 75-24-30) (SIN 61101) as
follows:
1 Install the machine bolt (01-020, 72-54-00) (SIN 92525) and machine
bolt (01-030) (SIN 61125).
(l) Install the existing bracket (01-195, 73-11-30) (SIN 34119) at the No.
5 fuel nozzle location as follows:
1 Install the machine bolt (01-260) (SIN 34122), machine bolt (01-040)
(SIN 12520), two clamps (01-060A, 73-11-40) (SIN 3418K), and two
machine bolts (01-050A) (SIN 3412L) to attach the bracket (01-195,
73-11-30) (SIN 34119). Refer to the GEnx-2B EM, 72-40-00, ASSEMBLY
001, CONFIG 02, Subtask 72-40-00-440-067 and Subtask
72-40-00-440-087.
(m) Install the existing bracket (20-220, 75-24-10) (SIN 61216) that
supports the 4th stage air tube (20-051) (SIN 61200) as follows:
1 Install the machine bolts (20-171) (SIN 61223) and bolts (01-060,
72-41-00) (SIN 12024), then remove the bracket (20-220, 75-24-10)
(SIN 61216). Keep parts for future use.
(n) Install brackets and air manifolds as follows:
1 For pre-GEnx-2B S/B 72-0144, do the assembly procedure that follows:
a Install the stage 4 manifold (20-010, 75-24-10) (SIN 61204).
Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 004, Subtask
72-00-02-440-129.
b Install the two igniters (01-010A, 74-21-20) (SIN 66200) and
connect the cables. Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY
004, Subtask 72-00-02-440-005.
c Install the thrust links and aft mount. Refer to the GEnx-2B,
Boeing 747-8 AMM, 71-21-02, REMOVAL/INSTALLATION, TASK
71-21-02-400-801-G00.
2 For post-GEnx-2B S/B 72-0144, do the assembly procedure that
follows:
a Install the igniters (01-010, 74-21-20) (SIN 66200) and ignition
cables (01-010, 74-21-10) (SIN 69100) on the engine. Refer to
the GEnx-2B EM, 72-00-02, ASSEMBLY 005, CONFIG 02, Subtask
72-00-02-440-508.
b Install the main igniter cooling shrouds (01-120, 74-21-10) (SIN
66202) on the two upper and lower igniters. Refer to the GEnx-2B
EM, 72-00-02, ASSEMBLY 005, CONFIG 02, Subtask 72-00-02-440-515.
(23)Install AGB heat shields and air manifolds as follows:
(a) Tighten the lower half HPT ACC manifold retaining bolts (15-170,
75-24-30) (SIN 62126). Refer to the GEnx-2B EM, 72-50-00, ASSEMBLY 001,
Subtask 72-50-00-430-057.
(b) Install the air manifold (20-030, 75-24-30) (SIN 61101) at the 4:30 to
7:00 o'clock position. Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 004,
CONFIG 01, Subtask 72-00-02-440-264.
(c) Install the manifold (20-021, 75-24-30) (SIN 61102) at the 7:30 to 9:00
o'clock position. Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 004,
Subtask 72-00-02-440-126.
(d) Install the stage 4 manifold (20-010, 75-24-10) (SIN 61204) at four
locations. Refer to the GEnx-2B EM, 72-00-02, ASSEMBLY 004, Subtask
72-00-02-440-130.
(e) Deleted.
(f) Deleted.
(g) Install the heat shields (40-020, 72-00-02) (SIN 29901), (40-030) (SIN
29902), (40-040) (SIN 29903), and (40-050) (SIN 29904) and panels

### Page 26

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
Date Printed:
2018/09/18
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
others or reproduced without the express written consent of
GE. Technical data is considered ITAR and/or EAR controlled;
transfer of this data to a Non-US Person, without USG
authorization, is strictly prohibited.
Page
26 of 28
(40-060) (SIN 29905) and (40-070) (SIN 29906). Refer to the GEnx-2B EM,
72-00-02, ASSEMBLY 005, Subtask 72-00-02-440-141.
(h) Deleted.
(i) Deleted.
E. Test
(1) Do a pressure test of the fuel manifolds as follows:
(a) Do a pressure check of the top fuel manifold (01-011, 73-11-40) (SIN
34101) and lower fuel manifold (01-021) (SIN 34102). Refer to the
GEnx-2B EM, 72-50-00, ASSEMBLY 001, Subtask 72-50-00-220-006,
paragraphs S.(1) through S.(7) only. [If the 9C1207 nitrogen cart or
the 11C4566 fuel adapter is not available, do an idle power leak check
post engine installation or during the test cell].
NOTE:When you do this Service Bulletin, to replace the top and lower fuel
manifold on an assembled engine/propulsor, the fuel nozzle valve
closure check specified in GEnx-2B EM, 72-40-00, ASSEMBLY 001, CONFIG
01, Subtask 72-40-00-220-004, paragraphs S.(8) and S.(9) is not
necessary and not to be accomplished.
NOTE:It is permitted to use filtered and pressure-regulated shop air
instead of nitrogen to do the pressure check.
(2) If necessary, do an engine test in a test cell or on wing as follows:
(a) If the test is done in a test cell, do a dry motoring check, an idle
leak check, and a high power leak check. Refer to the GEnx-2B EM,
72-00-00, TESTING 001 and TESTING 002.
(b) If the test is done on wing and the B-sump vent line was moved and
installed again during the fuel manifold replacement, refer to the
GEnx-2B, Boeing 747-8 AMM, to include Test Number 5 - Part Power Leak
Test.
(c) If the test is done on wing and the B-sump vent line was not moved
during the fuel manifold replacement, refer to the GEnx-2B, Boeing
747-8 AMM, to include Test Number 4 - Idle Leak Test.

### Page 27 (OCR)

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
MACHINE BOLTS  (01-020, 75-31-21)  (01-030, 75-31-21 RACKET  BRACKET
(SIN 61A20)  (SIN 61A12)
(EIGHT PLACES)  (34-230, 72-00-02)  BRACKET
, (SIN 61A13)  (01-070, 73-11-40)
BRACKET  (SIN 34110)  BRACKET
(01-070, 73-11-40)  (34-260, 72-00-02)
(SIN 34110)  (SIN 99210)
BRACKET
(01-070, 73-11-40).
(SIN 34110)
MACHINE BOLT
SUPPORT BRACKETS  (01-260, 73-11-30)
(SIN 34122)
(01-081, 73-11-40)
(SIN 34112)
MACHINE BOLT
(01-260, 73-11-30)  • SUPPORT BRACKETS
(SIN 34122) -  (01-081, 73-11-40)
(SIN 34112)
SELF LOCKING NUTS
(34-110, 72-00-02)  SPRING SLIDER
(SIN 17440)  (01-130, 73-11-40)
(120 LOCATIONS)  (SIN 34191)
(10 LOCATIONS)
SPRING
(01-140, 73-11-40)
BRACKET  (SIN 34190)
(01-070, 73-11-40)  (10 LOCATIONS)
(SIN 34110)  DAMPENER
BRACKET  (01-150, 73-11-40)
(01-100,73-11-40)  BRACKET  (SIN 34110)  (01-070, 73-11-40)  (SIN 34192)  (10 LOCATIONS)
(SIN 34117)  MACHINE
BOLTS  BRACKET  MACHINE BOLT
BRACKET  (05-040, 79-21-00 (34-240, 72-00-02)  (01-120, 73-11-40)
(05-060, 79-21-00)  (SIN 40A22)  (SIN 61113)  (SIN 34124)
(SIN 40A10)  (10 LOCATIONS)
BRACKET
(05-090, 79-21-00)
(SIN 40A1B)
OLD CONFIGURATION
5023936-00
Fuel Manifold Removal
Figure 1
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
Date Printed:  others or reproduced without the express written consent of  Page
2018/09/18  GE. Technical data is considered ITAR and/or EAR controlled;  27 of 28
transfer of this data to a Non-US  Person, without USG
authorization, is strictly prohibited.

### Page 28 (OCR)

GEnx-2B (LR) Service Bulletins (SBs)
SB 73-0038 R03 ENGINE FUEL AND CONTROL - Fuel Nozzle Manifolds (73-11-40) - Introduction
of New Fuel Manifold System Hardware
BRACKET  TOP FUEL MANIFOLD
(01-031, 75-31-21)  (01-011, 73-11-40)
(SIN 61A12)  (SIN 34101)
BRACKET
(SIN 61A20)  (01-020, 75-31-21)  MACHINE BOLTS  (SIN 61A13)  BRACKET  (34-236, 72-00-02)  (01-071, 73-11-40)  FUEL MANIFOLD  BRACKETS  (SIN 99210)  (34-261, 72-00-02)
(8 LOCATIONS)  (SIN 34110)
SUPPORT BRACKETS
(01-082, 73-11-40)
FUEL MANIFOLD  (SIN 34112)
BRACKETS
(01-071, 73-11-40)  SPRING SLIDER
(SIN 34110)  (01-131, 73-11-40)
(SIN 34191)
FUEL MANIFOLD  (10 LOCATIONS)
BRACKETS  SPRING
(01-071, 73-11-40)  (01-140, 73-11-40)
(SIN 34110)  (SIN 34190)
(10 LOCATIONS)
SUPPORT  NEW DAMPENER
BRACKETS  (01-151, 73-11-40)
(01-082, 73-11-40),  (SIN 34192)
(SIN 34112)-  (10 LOCATIONS)
BRACKET
(01-101, 73-11-40)L
(SIN 34117)
FUEL MANIFOLD
BRACKETS
(01-071, 73-11-40)
FUEL MANIFOLD  (SIN 34110)
BRACKET  BRACKETS
(05-061, 79-21-00)  (01-071, 73-11-40)  MACHINE BOLT
(SIN 40A10)  MACHINE BOLTS  (SIN 34110)  (01-120, 73-11-40)  (SIN 34124)
(05-091, 79-21-00)  BRACKET  (SIN 40A22)  (05-040, 79-21-00) BRACKET  (34-241, 72-00-02)  LOWER FUEL  MANIFOLD  (10 LOCATIONS)
(SIN 40A1B)  (SIN 61113)  (01-021, 73-11-40)
(SIN 34102)
NEW CONFIGURATION
5023940-00
Fuel Manifold Installation
Figure 2
GE PROPRIETARY INFORMATION - Subject to the restrictions on the media.
GE PROPRIETARY INFORMATION - Not to be used, disclosed to
Date Printed:  others or reproduced without the express written consent of  Page
2018/09/18  GE. Technical data is considered ITAR and/or EAR controlled;  28 of 28
transfer of this data to a Non-US  Person, without USG
authorization, is strictly prohibited.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
