# GE Aviation Czech Alert Service Bulletin ASB-H75-72-40: Revision 1, part 2 of 2

- Rights: © GE Aviation Czech. Filed by the FAA in regulations.gov docket FAA-2022-1239, the docket of AD 2022-26-01. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [GE Aviation Czech Alert Service Bulletin ASB-H75-72-40](https://openairdocs.org/service-documents/geac/asb-h75-72-40.md)
- Title as filed: GEAC Alert Service Bulletin ASB-H75-72-40 Rev 1-reduced size - 2 of 2
- Pages: 51
- PDF: https://openairdocs.org/files/sha256/e6/db/e6db91a065400d4dd2ac0af0188d86264f9d0d8b012b045d9fb1fdda3c336790
- Page: https://openairdocs.org/service-documents/geac/asb-h75-72-40/file/e6db91a06540

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

No of Sh:
81
Sheet No:
31
Outer combustion liner replacement disassembly
Description of Working Steps:
1.52. To the labyrinth seal of the GT back shaft, assemble preparation No. 200-475-2018 to 
restrict turning of rotor during unlocking the nuts of the GT disc. Insert protective cover 
400-476-0007 on the labyrinth.
1.53. Release progressively GT disc nuts with lockers and put them in storing plate No. 300-
745-7007 in the order they were disassembled, from 1 to 8. Loosen the nuts with 
adjusted wrench that can be inserted between the edge of the nut and protective cover. 
Insert preparation 200-475-
2018 to the back shaft and 
tighten with screw.
For labyrinth protection, 
insert protective cover 
400-476-0007
Before loosening the nuts,, 
protective cover must be inserted 
on the labyrinth.
Preparation to restrict turning of the 
rotor must be properly tightened.
Store the 
disassembled nuts in 
the storing plate 
according to the 
numbers (according 
to the position on the 
back shaft).
The direction of 
numbering of 
screws and nuts.

### Page 2

No of Sh:
81
Sheet No:
32
Outer combustion liner replacement disassembly
Description of Working Steps:
1.54. Disassemble the preparation to restrict rotor turning No. 200-475-2018.
1.55. Screw on two forcing-off screws 300-475-2006/01 against each other, if possible. Apply 
Molyka to the screw threads. Then release and remove the back 
shaft of the generator. Disassemble the forcing-off screws. Store 
the back shaft in a protective box. 
1.56.
1.57. Assemble GT disc Puller No. 100-476-2005/01. Then release and remove the GT disc and 
store it in a protective box to protect it from damage. Check the state of the blades for 
cuts and other damage (cracks, corrosion, etc.) If reassembly is to follow, store GT disc in 
freezer. 
Using two forcing-off screws 
force off and remove the 
generator back shaft from the 
engine.
Protective box
Protective box
Preparation 100-476-2005/1 assemble to the 
radial compressor box flange and to the disc. 
Using screws, widen the internal insert and 
remove the disc from the engine using other 
screw.

### Page 3

No of Sh:
81
Sheet No:
33
Outer combustion liner replacement disassembly
Description of Working Steps:
1.58. Remove the GT guide vane ring with assembled inner combustion liner.
1.59. On engine  versions with ecological drain container M601-227.3, a nozzle M601-206.6 
that leads from the ecological container through the centrifugal compressor case and 
outer combustion liner must be 
disassembled. Without removal of this 
nozzle, the outer combustion liner cannot 
be removed.
Remove GT guide vane ring with 
assembled inner combustion 
liner with slight pulling towards 
yourself.
GT guide 
vane ring
Inner combustion 
liner
Nozzle M601-206.6
that injects unburnt
fuel back to the 
combustion chamber.
Ecological drain
container M601-
227.6
This view is not possible in the aircraft 
engine, ecological drain container is 
placed behind the front firewall.

### Page 4

No of Sh:
81
Sheet No:
34
Outer combustion liner replacement disassembly
Description of Working Steps:
Loosen and disassemble hollow screw 
No. 1 along with sealing rings 10x14 CSN 
02 9310.2 (Copper, 2 pieces if drain pipe 
is installed, or 1 piece if the drain pipe is 
not installed). During disassembly of 
hollow screw No. 1 make sure the spring 
M601-2516.6 does not fall out from the 
container and does not get lost. Then 
disassemble the drain pipe (if installed).
Hollow 
screw No. 1
Drain pipe
Copper sealing rings 
of the hollow screw 
No. 1 (2 pieces) and 
No. 2 (2pieces).
Hollow 
screw No. 2
Check the nozzle for 
damage caused by 
outer liner.
Hollow 
screw No. 1 Hollow 
screw No. 2 Spring
After disassembly of hollow screw No. 1 
and the drain pipe, loosen the hollow 
screw No. 2 along with the sealing rings 
24x30 CSN 02 9310.2 (Copper, 2 pieces, 
under and over the container). Then, 
remove spring M601-2516.6 from the 
insides of the ecological container (if it 
has not fallen out during disassembly of 
hollow screw No. 1), screen and nozzle
M601-206.6.Nozzle M601-206.6

### Page 5

No of Sh:
81
Sheet No:
35
Outer combustion liner replacement
disassembly, visual check
Description of Working Steps:
1.60 Remove outer liner from the engine. Turn it to loosen it from the bayonet and pull lightly 
towards yourself for removal.
1.61 Cover the engine with canvas or the radial compressor box flange with plastic to prevent 
entrance of foreign objects or impurities in the engine. Check that all pipes and openings are 
sealed, including the disassembled pipes.
2 Visual check
All engine parts must be carefully visually checked. Checks focus on lifespan, cracks, surface, 
contact surfaces, etc.
Specify any damage according to the respective maintenance manuals. Information below is 
indicative only.
2.1 Check of GT and PT discs: the front part of the discs may show traces of scraping and cuts to 
the depth of max. 0.1 mm. Brush these traces with a light sand cloth, no cuts or scraping are 
allowed at the area of blades hinges.
2.2 Check of GT blades: scraping of edges around the perimeter is allowed. Brush the scraping 
on the blade with light sand cloth. Tightened material and cuts on blades is only allowed to 
one third from the top of the running edges to the dept of max. 0.5 mm without sharp 
changes. On the other surfaces of the blades, in particular in the area of trimming edges, no 
damage is allowed. Damaged areas must be brushed and polished.
2.3 Deflector check: even deformed areas, if cuts create a closed circuit, reject the deflector. 
Any change of defective deflector is allowed.
2.4 Other parts that must be checked, are: GT guide vane ring, PT guide vane ring, Inner 
combustion liner, outer combustion liner, fuel manifold deflector, deflector lock washers, 
diffuser vanes lock washers, straightening blades, GT bolt threads, bearings, ecologic drain 
canister nozzle, GT and PT blades, tightness of all threaded connections and thermocouples 
(measure).

### Page 6

No of Sh:
81
Sheet No:
36
Outer combustion liner replacement   
visual check
Description of Working Steps:
If the tabs on the Lock Washers on the deflector are damaged or missing, remove the nut LN 
5136, replace the Lock Washer LN 5333, apply Molyka to the thread, install the nut and torque to 
Safety the Lock Washer.
Replacement of the Lock Washers on the Diffuser Vanes:
On H-series engines: The bigger tab on the Diffuser Vanes Lock Washer M601-1092.4 must go in 
the hole in the diffuser, torque the nut XM601-
On M601 series engines: Remove both nuts M601-1181.4 which are connected by the double 
Lock Washer M601-1063.4, replace the Lock Washer, apply Molyka to the thread, install both nuts 
Deflector Lock Washers LN 5333 6 pieces Diffuser Vanes Lock Washers:
For H-series engines M601-1092.4
For M601 series engines M60-1063.4
The bigger tab on the Lock Washer 
must touch the side wall of 
the Deflector
Correct condition of the Lock 
Washers

### Page 7

No of Sh:
81
Sheet No:
37
Outer combustion liner replacement cleaning small parts
Description of Working Steps:
3 Cleaning
3.1 All small parts of the PT guide vane ring (in particular flanges) with remains of sealing pastes 
clean with Scotch-Brite or similar. Then degrease with acetone. Brush cuts and lines.
3.2 Clean the spacers under the bearing body (if part of the engine).
Clean all PT guide vane 
ring flanges from 
sealing pastes.
Clean oil pressure pipe 
flanges -343.9 and oil 
scavenge pipe flanges -304 
from sealing pastes.
Clean spacer from sealing 
pastes. The engine may 
include two washers or 
none.

### Page 8

No of Sh:
81
Sheet No:
38
Outer combustion liner replacement cleaning small parts
Description of Working Steps:
3.3 If no new cover of the oil collector is needed for reassembly, clean the flanges on the cover of 
the oil collector from sealing pastes.
3.4 Clean the flanges of the GT guide vane ring and spacer M601-2016.4 A-E (inserted between 
flanges of the inner combustion liner and GT guide vane ring, if assembled).
3.5 Clean the flange on the labyrinth from sealing paste.
Thoroughly clean 
the GT guide vane 
ring flange in the 
area of studs.
Clean the spacer if 
assembled.
Clean the flanges on the 
cover of the oil collector 
and of the pressure oil and 
discharge oil pipes.
Clean thoroughly 
the labyrinth flange 
even between 
studs.
Clean the internal 
diameter from 
carbon.

### Page 9

No of Sh:
81
Sheet No:
39
Outer combustion liner replacement cleaning small parts
Description of Working Steps:
3.6 Clean the air intake pipe flanges -880.9 and air inflate pipe flanges -828.7 from sealing pastes.  
3.7 Clean the centrifugal compressor case flange and washer to be placed between the centrifugal 
compressor case and the exhaust case (does not have to be part of the engine).
Air intake pipe -880.9 Air inflate pipe -828.7
Clean the centrifugal
compressor case flange.
Clean the spacer
from both sides (if 
installed).
While cleaning this flange, 
cover the engine to prevent 
impurities from cleaning 
from entering the engine.

### Page 10

No of Sh:
81
Sheet No:
40
Outer combustion liner replacement assembly
Description of Working Steps:
4 Assembly
4.1 Slide the outer liner to the engine and turn it to lock it in bayonet. Make sure the liner is in the 
correct position (marking XXX upwards, and openings opposite the torch igniter flame 
progagating tubes).  
4.2 On engine versions with ecological drain container M601-227.3, install the nozzle M601-206.6, 
that goes from the ecological container through the centrifugal compressor case and outer 
combustion liner. Outer combustion liner must 
include a special opening for the nozzle.
Insert outer combustion liner to the 
engine, maintain the correct position 
XXX .
Needle that injects 
unburnt fuel back to 
the combustion 
chamber.
Ecological container 
M601-227.6
This view is not 
possible in the 
aircraft engine, 
ecological container is 
placed behind the 
front firewall.

### Page 11

No of Sh:
81
Sheet No:
41
Outer combustion liner replacement assembly
Description of Working Steps
Insert a sealing ring 24x30 CSN 02 9310.2 
between the centrifugal compressor case
and ecological drain container and then 
insert the nozzle M601-206.6 with screen 
to the container in the correct position 
(with the position rod in the opening on 
the side of the centrifugal compressor 
case). Then insert hollow screw No. 2 with 
sealing ring 24x30 CSN 02 9310.2.
Install the drain pipe (if applicable) and 
put the spring M601-2516.6 under the 
nozzle, then install the hollow bolt with 
sealing ring 10x14 CSN 02 9310.2 (2 
sealing rings, if the drain pipe is used 
one sealing ring on each side of the pipe 
connection).
Hollow screw 
No. 1
Drain pipe
Copper sealing 
rings of the hollow 
screw No. 1 (2 
pieces) and No. 2 
(2pieces.)
Hollow screw 
No. 2
Spring
Nozzle M601-206.6

### Page 12

No of Sh:
81
Sheet No:
42
Outer combustion liner replacement assembly
Description of Working Steps:
5 Assembly
5.1 Mount over the main shaft to the locks on the outer combustion liner the GT guide vane ring
with assembled inner combustion liner. Maintain the correct mutual XXX
designation always upwards.
5.2 Preheat centring opening in the main shaft for mounting (or forcing on) of the GT disc to the 
temperature of 90-
0 XXX disc
marked with red pen. Tighten the GT disc through the 400-475-2112 to contract surface with 
technological nuts. Apply the mixture of molybdenum sulphide and oil (Molyka) in weight ration 
2:1 to the main shaft centring before forcing on the GT disc. CAREFUL: the mixture must not 
contaminate the contact surface of the 
disc. 
GT guide 
vane ring
Inner 
combustion 
liner
Insert GT guide vane ring to 
the locks on the outer 
combustion liner
Centring opening in the main 
shaft can be preheated with 
heat gun.
Check the cleanness of the contact 
surface, apply Molyka and then heat 
them up.

### Page 13

No of Sh:
81
Sheet No:
43
Outer combustion liner replacement assembly
Description of Working Steps:
5.3 Before mounting to the GT disc, heat up the centring of the back shaft to 90-
back shaft GT - nd centring of 
the GT disc
the mixture of molybdenum sulphide and oil in weight ration 2:1 (Molyka) to centring of back 
shaft pursuant to instruction M601-P13-20. CAREFUL: The mixture must not contaminate the 
contract surface of the disc. Execute further assembly after the small parts cool down. Make 
sure the parts are correctly positioned.
Preheat centring of the 
back shaft to 90-
using the preparation or 
heat gun, then apply 
Molyka and insert it on 
the screws of the main 
shaft.
Mount the disc on the main shaft, make sure both parts 
are in the right position, the top of the main shaft is where 
positioning, mark the tops with red pen.
Apply Molyka to the centring 
of the main shaft. Be careful, 
Molyka must not 
contaminate the contact 
surface of the disc. If this 
happens, clean it.
Force the disc on 
the main shaft using 
preparation 400-
475-2112 and at 
least four 
technological nuts.
Careful: Molyka must 
not contaminate the disc 
contact surface.

### Page 14

No of Sh:
81
Sheet No:
44
Outer combustion liner replacement assembly
Description of Working Steps:
5.4 Apply thin layer of the mixture of molybdenum sulphide and oil in the weight ratio 2:1 to the 
threading and contact surfaces of nuts 3241.7 (nuts to GT disc) pursuant to instruction M601-
P13-20. CAREFUL: do not apply to GT disc screw threading. Only nuts.
5.5 Mount the back shaft to the centrifugalcompressor case flange preparation to prevent turning 
of rotor 200-475-2018 and tighten it. Insert washers -3048.4 to the GT disc screws. Before 
mounting the nuts, mount the auxiliary technological ring 400-476-0007to the back shaft. The 
ring will limit the position of the washers to secure clearance V3/27. Then insert nuts -3241.7 to 
the screws. Focus on the correct order of nuts. Mutual exchange of nuts can only be executed if 
the same weight is maintained with 0.01g tolerance. 
Preparation to 
prevent turning of 
rotor.
Auxiliary technological 
ring
Washers and nuts with 
applied Molyka
Apply thin layer of 
molybdenum sufide and oil 
(Molyka) to threading and 
contact surfaces of all eight 
nuts.

### Page 15

No of Sh:
81
Sheet No:
45
Outer combustion liner replacement assembly
Description of Working Steps:
5.6 Torque all nuts crosswise to 7.85 Nm.
5.7 Mount the preparation for measuring of bolt stretch 300-557-0036/01 and tighten each screw 
twice to the extension 0.155-0.16mm and back and watch whether the screw returns to the 
original position after loosening. Tighten screws crosswise. Final tightening execute crosswise to 
the value of 0.110-0.115 mm. During that, measure the tightening moment, that must not 
exceed 12.7 Nm,. 
Each screw tighten twice to the extension 
0.155-0.16 mm and back (i.e. from 0 to 
0.155-0.16mm, back to 0 and check whether 
the screw returns to 0 and then back to 
0.155-0.16 mm and back). Final tightening 
execute crosswise to the value of 0.110-
0.115 mm. During that, measure the 
tightening moment, that must not exceed 
12.7 Nm.
Preparation for measuring 
the bolt stretching.
Preliminarily torque all nuts 
crosswise to 7.85 Nm .

### Page 16

No of Sh:
81
Sheet No:
46
Outer combustion liner replacement assembly
Description of Working Steps:
5.8 Secure the GT disc screw nuts by bending the washers according to the picture, and the holders 
of the washers hammer down so that the washer sits on the back shaft with its whole surface. 
Then bend the back part of the washer so it flattens on the side at the auxiliary ring and limits 
the clearance between the sealing labyrinth and lock washer of GT screws. Then disassemble 
the preparation to prevent turning of rotor 200-475-2018 and auxiliary ring 400-476-0007. After 
securing, execute visual check.
Secure lock washers with 
pin, bend the side to the 
cuts on the nut.
In this area, 
hammer down 
the washer to sit 
on the back shaft 
with the whole 
surface.
Define the clearance carefully in 
order not to damage the labyrinth.
Clearance between the labyrinth 
and the GT lock washer is limited 
by bending the back side of the GT 
washer. The result must look as in 
the picture.
        Procedure:
1) Securing
2) Hammering down
3) Defining the clearance
4) Visual check
2)
  4)
1)
3)

### Page 17

No of Sh:
81
Sheet No:
47
Outer combustion liner replacement assembly
Description of Working Steps:
5.9 Apply ALHYL paste to the sealing surfaces of the GT guide vane ring and PT labyrinth -366.7, to 
the sealing surfaces of the PT guide vane ring and the centrifugal compressor case and also to 
the sealing surfaces of PT and GT guide vane rings. 
5.10 Mount labyrinth -366.7 to the PT guide vane ring and lightly technologically connect it to the 
PT guide vane ring with nuts and technological washers. Labyrinth -366.7 must be positioned 
PT guide vane ring .
Assembled PT 
guide vane ring
with labyrinth, 
internal view.
Apply ALHYL paste to all 
internal contact surfaces of PT 
guide vane ring.
Apply ALHYL 
paste to contact 
surface of the 
labyrinth.
Apply ALHYL paste to the 
centrifugal compressor case
flange and GT guide vane ring
flange.
Mount labyrinth -366.7 to the PT guide 
vane ring and technologically connect it 
with two nuts and washers.
Designation 
XXX
is on the side of 
the labyrinth, 
designation is on 
the other side 
opposite shorter 
screw.

### Page 18

No of Sh:
81
Sheet No:
48
Outer combustion liner replacement assembly
Description of Working Steps:
5.11 Mount PT guide vane ring on the GT guide vane ring according to the position mark, with 
technologically assembled labyrinth with centring to the centre of the centrifugal compressor 
case and GT guide vane ring. 
Mount to the PT guide vane ring
with assembled labyrinth -366.7 
on the GT guide vane ring and 
to the centrifugal compressor 
case flange. Position PT guide 
vane ring upwards and against 
the GT guide vane ring.
CAREFUL: If there was a spacer 
between the PT guide vane ring
and the centrifugal compressor 
case, it must be inserted under the 
guide vane ring again. Be careful 
not to confuse it with the washer 
between PT guide vane ring and 
exhaust case. Aply ALHYL to both 
sides of the spacer.
GT guide vane 
ring screws
Top screw of the GT 
guide vane ring
designated with red 
colour.

### Page 19

No of Sh:
81
Sheet No:
49
Outer combustion liner replacement assembly
Description of Working Steps:
5.12 Technologically assemble the PT guide vane ring to the compressor case with 4 screws and nuts 
with M5 washers. Assemble the PT guide vane ring to the GT guide vane ring according to the 
position mark using LN 5250 nuts and lock washers 5.2 ONL 3288.2. Apply Molyka to the screw 
threads
Mount nuts to the GT guide 
vane ring screws and tighten 
Technologically connect the 
PT guide vane ring to the 
centrifugal compressor case. 
(At least 4 screws crosswise)
Secure the 
lock washers.
Use extension 400-313-7004 
on the torque wrench and do 
not forget that by extending 
the arm, the ratio of the 
indicator of the moment 
value is changed, too. The 
value must be recalculated.

### Page 20

No of Sh:
81
Sheet No:
50
Outer combustion liner replacement assembly
Description of Working Steps:
5.13 Loosen, screw out and remove the nuts with washers that technologically connect the 
labyrinth to the PT guide vane ring.
5.14 Degrease and apply ALHYL to the sealing surface of the bearing body opposite the PT guide 
vane ring, also apply ALHYL to the PT guide vane ring. If spacer was under the body (could 
have been two), degrease it and apply ALHYL paste, too. Do not forget to position the washer 
correctly so that all openings in the bearing body are aligned with the openings in the washer. 
Apply grease to the inner side of the outer ring of the bearing.
5.15 To the inner ring of the roller bearing, insert the cage with rollers. Before assembly apply 
grease to the cage with rollers.
During assembly pay 
increased attention. 
Conduct the assembly in 
clean white gloves.
On the bearing body, apply 
ALHYL to both contact sides.
Apply grease to 
the inner side of 
the external ring 
of the bearing.
Apply ALHYL paste to the 
sealing surface.. 
Before assembly, 
apply grease to the 
cage with rollers.

### Page 21

No of Sh:
81
Sheet No:
51
Outer combustion liner replacement assembly
Description of Working Steps:
5.16 Tie two rubber bands together (must be new). Then insert the rubber band to the cage with 
rollers so that the rubber band presses all rollers towards the inner ring. 
5.17 Carefully mount the bearing body to the inner ring of the roller bearing according to position 
marks while centring the external ring of the bearing to the rollers and centring of the bearing 
body to the centring of the guide vane ring. Slide the free part of the band through one of the 
openings in the bearing body. After light mounting of the bearing body to the cage with rollers, 
pull out and cut the band that held the bearing rollers. After removal of the band make sure no 
part of it remained in the area of the bearing (both ends of the band must be clearly cut).
The bearing body mount on the 
cage with rollers and centre it 
according to the PT guide vane 
ring. Using tweezers, pull the 
free part of the band through 
the opening in the body.
Insert the rubber band to the 
cage with rollers so that the 
rubber band presses all 
rollers towards the inner 
ring.
Pull the free part of the 
band to take out the part 
that holds together the 
rollers in the bearing cage. 
Cut it and remove the 
band.
Check the cut band. 
The cut must be 
clean. No part of 
the band can 
remain in the 
engine.

### Page 22

No of Sh:
81
Sheet No:
52
Outer combustion liner replacement assembly
Description of Working Steps:
5.18 Using at least 4 technological nuts and technological spacers crosswise evenly tighten the 
body to the guide vane ring flange and technologically pre-assemble the bearing body. 
Tightening must be completely even. During installation, lightly turn the rotor, which must 
turn freely during the whole tightening. Apply ALHYL to the thread and countersunk head of 
those bolts. Connect the bearing body to the PT guide vane ring along with the labyrinth using 
2 screws M3x10 CSN 02 1151.22. Loosen technological nuts with washers. 
5.19 Remove technological nuts and spacers from the Bearing Housing M601-3046.9. 
The bearing body 
pre-assemble 
using four nuts 
and spacers.
Then assemble 
the bearing body 
with two M3x10 
screws with the 
top of their heads 
under the flange 
level.
Bearing Housing
M601-3046.9

### Page 23

No of Sh:
81
Sheet No:
53
Outer combustion liner replacement assembly
Description of Working Steps:
5.20 Apply sealing compound Alhyl to the flange contact surface of the Oil Sump Cover XM601-
3505.5 and Bearing Housing M601-3046.9 with 2 pieces of bolts M3x10.
5.21 Install the Oil Sump Cover XM601-3505.5 and Deflector M601-3043.4 with the TOP mark 
NOTE: Put the Deflector M601-3043.4 with the divided part to the top of the engine and 
the Oil Sump Cover XM601-3505.5.
Oil Sump Cover XM601-3505.5
 Bearing Housing M601-3046.9
Alhyl sealing compound
Alhyl sealing compound layer
Oil Sump Cover
XM601-3505.5
 TOP mark
Deflector M601-3043.4 - 3 pieces

### Page 24

No of Sh:
81
Sheet No:
54
Outer combustion liner replacement assembly
Description of Working Steps:
5.22 Put 12 pieces of pre-bent Lock Washers 5,2 ONL 3288.2 and apply Molyka to 
the threads of the stud bolts.
5.23 Install 11 Nuts LN 5250 and 1 Nut LN 5251 to the stud bolts. Install the Nut LN 5251 under 
the flange for the scavenge oil pipe M601-304.6. The tabs of the Lock Washers must touch 
the Oil Sump Cover XM601-3505.5, hold the Lock Washers 5,2 ONL 3288.2 in position to 
prevent movement. Torque 11 pieces of Nuts LN 5250 to 5,8+0,2 Nm and 1 piece of Nut LN 
Oil Sump Cover 
XM601-3505.5
Lock Washer 
5,2 ONL 3288.2                
12 pieces
LN 5251
Flange for the oil scavenge pipe 
M601-304.6
LN 5250
Oil Sump Cover XM601-3505.5

### Page 25

No of Sh:
81
Sheet No:
55
Outer combustion liner replacement assembly
Description of Working Steps:
5.24 Safety all nuts with the 12 Lock Washers 5,2 ONL 3288.2.
5.25 Install the Pressure Oil Pipe M601-342.9 to the Oil Sump Cover XM601-3505.5. Put the 
Gasket M601-3012.5 between Pressure Oil Pipe M601-342.9 and the Oil Sump Cover 
XM601-3505.5 and install 2 Bolts M601-3005.3 and 2 Lock Washers 5,2 ONL 3288.2. Apply 
sealing compound Alhyl to both sides of the Lock Washers 5,2 ONL 3288.2 and to the 
threads and under the head of the Bolts M601-3005.3 and install Lock Washers and Bolts 
immediately. Torque both Bolts M601-3005.3 in 3 steps: first step torque both Bolts to 
Oil Sump Cover
XM601-3505.5
Lock Washer 5,2 ONL 3288.2                
12 pieces

### Page 26

No of Sh:
81
Sheet No:
56
Outer combustion liner replacement assembly
Description of Working Steps:
5.26 Install the Pressure Oil Pipe M601-304.6 to the Oil Sump Cover XM601-3505.5. Put the Gasket M601-
3010.5 between Pressure Oil Pipe M601-304.6 and the Oil Sump Cover XM601-3505.5 and install 2 
Bolts LN 5135 and 2 Lock Washers 5,2 ONL 3288.2. Apply sealing compound Alhyl to both sides of 
the Lock Washers 5,2 ONL 3288.2 and to the threads and under the head of the Bolts LN 5135 and 
install Lock Washers and Bolts immediately. Torque both Bolts LN 5135 in 3 steps: first step torque 
Bolt M601-3005.3 - 2 pieces
Pressure Oil Pipe M601-342.9
Lock Washers 5,2 ONL 3288.2            
2 pieces
Gasket M601-3012.5
Gasket M601-3010.5
Lock Washers 5,2 ONL 3288.2            
2 pieces
Bolt LN 5135 2 pieces
Scavenge Oil Pipe M601-304.6

### Page 27

No of Sh:
81
Sheet No:
57
Outer combustion liner replacement assembly
Description of Working Steps:
5.27 Check for the correct clearance of minimum 1 mm around the Pressure Oil Pipe M601-342.9 and 
Scavenge Oil Pipe M601-304.6.
5.28 Safety the bolts on the Pressure Oil Pipe and Scavenge Oil Pipe with the 4 Lock Washers 5,2 ONL 
3288.2.
5.29 Apply Molyka to the inner threads in the PT NGVR for the Bolts M601- 3004.3 for connection 
with the Cooling Air Deflector M601-329.5.
Lock Washers 5,2 ONL 3288.2            
2 pieces
Lock Washers 5,2 ONL 3288.2            
2 pieces
Molyka

### Page 28 (OCR)

No of Sh: 81
GE Aviation  Business & General Aviation  Sheet No: 58
Outer combustion liner replacement - assembly
Description of Working Steps:
5.30  Install the Cooling Air Deflector M601-329.5 into the PT NGVR with the TOP mark („XXX") to the top
of the engine. Install 12 Bolts M601-3004.3 and torque them crosswise to 2t0,2 Nm.
Cooling Air Deflector M601-329.5
Bolt M601-3004.3
12 pieces
5.31  Safety the 12 bolts with Locking Wire dia. ø0,63 mm.
Locking Wire ø0,63 mm

### Page 29

No of Sh:
81
Sheet No:
59
Outer combustion liner replacement assembly
5.32 Manually turn the GT rotor. Turning must be easy and no strange sounds must come 
from the area of the generator.
5.33 Bind lashing wire to cap nuts of the oil intake pipes -342.9 and oil discharge pipes -304.6, 
i.e. cap nuts -3006.9 and -3007.9 for subsequent pulling the nuts from the outlet system
so that it has at least 250 mm. At M601D also bind the lashing wire to the bushing from 
the thermocouples.   
5.34 From the outlet system of the engine, disassemble the sealing from the lateral flange and 
one exhaust bend. Clean the contact surfaces of the flanges.  Center the position of the 
piston ring in the PT guide vane ring by putting a piece of paper under the piston ring 
ends.Cut overlapping paper with razorblade.
Bind lashing wire to 
the cap nuts (or 
thermocouple 
bushing). Using the 
wire, you will be able, 
after connecting the 
outlet system of the 
generator, to pull the 
nuts through the 
outlet system.
Correct placing of the piston ring is achieved by 
insertion of piece of paper under the piston 
ring. Subsequently cut the paper.

### Page 30

No of Sh:
81
Sheet No:
60
Outer combustion liner replacement assembly
Description of Working Steps:
5.35 At the front holder on the engine splitting preparation connected to the outlet system, 
connect the crane and carefully slide it on the bearing part of the engine splitting 
preparation fixed on the aircraft. After mounting, before loosening the crane, stop the 
remove the crane hook.
with the outlet
system of the 
engine on the 
holder using screw 
on the front holder.
Insert stopper bolt 
on the bearing part 
of the outlet
system.
Fix the crane using 
the front holder.
After mounting the outlet
system of the engine to the 
bearing part of the engine 
splitting preparation, 
disconnect the crane and 
prepare leading needles (6 
pieces around the 
perimeter).
Stopper bolt

### Page 31

81
Sheet No:
61
Outer combustion liner replacement assembly
Description of Working Steps:
5.36 Disassemble technological screws from the GT guide vane ring flange and centrifugal 
possible to pull through lashing wires connected to cap nuts -3006.9 and -3007.9 through the 
exhaust case coat in the appropriate places (at M601D, pull the wire through from the 
thermocouple bushing). Then slide the outlet system to the position where the centring 
needles touch the front of the PT guide vane ring flange. In this position, check and adjust, if 
necessary, evenness of flanges, insert around the perimeter in the openings other six leading 
needles, then mount centring needles in the relevant openings in flanges of the PT guide vane 
ring and the ce ntrifugal compressor case. Slide the outlet system even further so that the 
space between the flanges is 20 mm in maximum, in this position, check again alignment of 
flanges, if necessary, set with screw No. 1 on the preparation. Screw No. 2 must be free, 
during approximation keep checking with your hand the mobility of the power (free) turbine. 
After securing the correct position, lightly move the outlet system to the PT guide vane ring 
flange and secure it with at least 6 screws with applied Molyka. Cap nuts of oil pipes - 3006.9 
and -3007.9 pull through the coat of the exhaust case (at M601D, pull also the bushing from 
the thermocouples through the coat and measure it). CAREFUL: do not forget to insert the 
spacer between the exhaust case and flange of the PT guide vane ring if it was part of the 
engine. Check evenness even from the side (not only height-se), if necessary, press the outlet 
system to the relevant side.
If washer was part of the engine, 
it must be reassembled. Check mobility of the 
PT turbine with your 
hand inserted in the 
exhaust. If the turbine 
gets stuck, the system 
must be returned to 
the position where it 
moved, and then 
continue in bearing on, 
or adjust the position.
Pull the cap nuts wires through the 
relevant openings.
Conduct bearing on very 
slowly and carefully. The 
flanges must be 
completely even all the 
time. Keep checking the 
mobility of the PT 
turbine.
Make sure 
the nut 
does not 
prevent 
sliding.

### Page 32

No of Sh:
81
Sheet No:
62
Outer combustion liner replacement assembly
Description of Working Steps:
5.37 Add number of other screws to the flange (in particular short ones, do not forget to rub 
them in Molyka) and disassemble the engine splitting preparation from the engine. This 
reduction gearbox holder, the other part with centring needles and the third part (while 
disassembling the third part, replace the pins of the preparation with pins of the engine bed 
progressively, the engine bed needles with crown secure with cotter pin.) Add screws and 
nuts to the longitudinal parting flange of the exhaust case at the openings from 
disassembled parts of the preparation.
Disassemble all parts of the engine
splitting preparation and store 
them in the case.
Disassemble the second 
part of the preparation 
with centring needles 
from the top and bottom 
part.

### Page 33

No of Sh:
81
Sheet No:
63
Outer combustion liner replacement assembly
Description of Working Steps:
5.38 Connect the flanges of the centrifugal compressor case and the outlet system using 41 
screws -3007.7, 19 screws -8019.7 (rub them in Molyka) and 60 self-locking nuts - 3009.4 
(numbers of long and short screws may differ, long screws are where a holder is connected 
under the nut). In the 10th opening (counted from the top connection of the outlet system 
) insert screw -
also holder -8015.6 (slightly turned to the top of the engine). Insert holders of the front 
partition under the nut of 5th, 15th and 25th screw, also insert and use screws - 8019.7. At 
positions 11 and 12, insert the holder of the fire detector under the nuts (if assembled).
To openings 2, 8, 14, 20 and 26 (right half of the engine), also insert screws -8019.7, connect 
the holders of the thermocouple collector under the nuts on these screws.
To openings 3, 4, 6, 7, 8, 16, and 26 ( counted from the bottom connection of the outlet
system clockwise) insert -8019.7. Under the nuts of screws 3 and 4, insert the top part of 
the holder -839.8, at screw 6 and 7, insert the top part of the holder -840.8 under the nut. 
Under the nut of screw 5, 15 and 25, insert the holders of the front firewall -8044.6. Under 
nuts 9, 16 and 26, connect the thermocouple collectors. On position 25 and 26, insert the 
holder of fire detector (if assembled).
Tighten the nuts crosswise to 6 Nm.
Screws with nuts under 
which the thermocouple 
collectors are connected.
Screws with nuts under 
which the holders of the 
front firewall are 
connected.
Screws with nuts under 
which the fire detector 
holder are connected.
Screws with nuts under 
which the top parts of 
the holders -839.8 and -
840.8 are connected 
assemble by oil pipes.
Screw with nut under 
which the holder -8015.6 
is connected.
PL
2.
8.
14.
20.
26.
9.
16.
26.

### Page 34

No of Sh:
81
Sheet No:
64
Outer combustion liner replacement assembly
Description of Working Steps:
5.39 Do a visual inspectionand resistance measurement of each thermocouple. 
Visual inpection: contacts without movement (wobbling) and not bended, nut on the 
measuring end must be tight.
Electrical resistance inspection: measure both electrical resistance of the thermocouple 
(between the two contacts) and insulation resistance of the thermocouple (between one 
of the contacts and the thermocouple casing).Do visual inspection: contacts without 
movement (wobbling), not bended, nut on the measuring end must be tight.
Pass / fail criteria:
1)
2)
5.40 To nine flanges on the exhaust case progressively insert 9 thermocouple transmitters (does 
not apply to M601D). Each thermocouple must go to the same place from which it was 
removed, their position is marked according to 1.22. Before tightening check whether each 
transmitter sits well in the flange, then tighten it with 2 screws LN 5444 (apply Molyka to 
the inner threads in the exhaust case), insert lock washers 5.2 ONL 3288.2 under the screw 
heads, secure the screws after tightening. Do the resistance measurement again, refer to 
step 5.32. Install 
gearbox.  
5.41 Connect to the exhaust case flange thermocouple transmitter bus. According to the sketch 
on sheet 63. Before the bus platform is fixed, according to the need, release its 
inconvenient distortion with hand so that individual wires to be tightened and connected 
to individual poles of the thermocouple transmitters are not under extreme pressure, 
distorted, crossed, slacking, etc.
To the flanges on the exhaust 
case, insert 9 thermocouple 
transmitters. Before tightening, 
try to centre the thermocouple 
transmitters.
Thermocouple 
transmitters position with 
reduction gearbox. After 
tightening of the screws, 
secure the lock washers.
CONTACTS
THERMOCOUPLE CASING NUT
MEASURING TIP

### Page 35

No of Sh:
81
Sheet No:
65
Outer combustion liner replacement assembly
Description of Working Steps:
5.40 Assemble cables to the thermocouple transmitters. Connect cables with red insulation to 
with LN 5084 bolts and LN 5167 self-locking nuts and the cables with green 
insulation with LN 5444 bolts and LN 5168 self-locking nuts. Position the cable 
heads to be almost horizontal with the exhaust case and to be oriented anti-clockwise 
(viewing from the direction of flight). The only exception is the connection of two 
thermocouple transmitters, where in one case, the cable heads are oriented to the front 
partition (at the thermocouple transmitter located next to the flange for intake of cooling air 
of the GT oil collector cover) and in the other thermocouple transmitter, the cables are 
oriented clockwise (the lowest thermocouple transmitter on the left side of the exhaust 
case). While connecting the wires to the thermocouple transmitter poles, make sure the 
wires are not torn, partially broken, crossed (i.e. damaged) and that the outlet thermocouple 
contacts are not damaged bent during assembly. During tightening, hold the screws, then 
secure them and place the wire eyes under the screw heads. After assembly, check insulation 
resistance of the whole thermocouple set the insulation resistance must amount to at least 
the holder can be put together from two parts, in certain strongly 
bandaged places of the platform, holder insert cannot be used. During assembly of the cable 
platform, maintain the distance of the cable outlets from the pipes (at least 5mm), at the 
platform, contact of braid and pipes is allowed. The screws are inserted to the thermocouple 
transmitters poles from the accessory gearbox, at the transmitter on the left side, they are 
inserted from top to bottom, and at the transmitter thermocouples (the bottom one on the 
left), they are inserted from the reduction gearbox.
At M601D version, 
connect the bus to the 
bushing in the exhaust 
case.
On the left side of the engine, 
there are two thermocouple 
transmitters exceptionally 
positioned this way.

### Page 36

No of Sh:
81
Sheet No:
66
Outer combustion liner replacement assembly
Description of Working Steps:
5.41 At the exhaust case opening (pressure oil intake), take out the oil pipe cap nut using the 
lashing wire (or hook) through the sealing connection. Using the cap nut on the oil intake 
pipe, connect the pressure oil bushing -829.9, the bushing must be oriented for subsequent 
connection of the pressure oil pipe to GT. 
5.42 At the opening in the exhaust case (oil scavenge), take out the oil pipe cap nut using lashing 
wire (or hook) through the sealing connection. Using cap nut, connect the pressure oil 
bushing -8030.9 to the oil discharge pipe. Using cap nut, assemble the bushing to the oil 
discharge pipe and secure the cap nut.
Insert sealing rings to ONL connections. CAREFUL: 
you must be absolutely sure that the ring did not 
move and does not prevent oil flow or cause pipe 
leakage.
Connect bushing using cap 
nut.
Insert sealing rings to ONL connections. 
CAREFUL: you must be absolutely sure 
that the ring did not move and does not 
prevent oil flow or cause pipe leakage.
Connect the 
bushing using cap 
nut with scavenge
pipe and secure 
both.
Connect the bushing using cap nut.
Apply   
Molyka to the 
bushing 
threading.
Apply   
Molyka to 
the bushing 
threading.

### Page 37

No of Sh:
81
Sheet No:
67
Outer combustion liner replacement assembly
Description of Working Steps:
5.43 To the hollow screw of the drain pipe LN 6169, insert sealing ring (Cu) 10x14 CSN 02 9310 
and slide it through the drain pipe -806.7, then mount another sealing ring on the screw and 
screw it to the flange threading on the bottom of the exhaust case. Secure the screw with 
lashing wire. Before assembly, apply Molyka to the hollow bolt threading. 
5.44 Slide cover -8048.8 on the torqumeter pipe -840.9. Connect the torquemeter pipe to the 
pipe -841.6 using cap nut. Tighten the nut and secure with lashing wire. Then mount the 
sealing -8060.8 (2 pieces) and rubber insert -8061.8 to the pipe. Fix the sealing and rubber 
insert to the front firewall using covers -8048.8, fix the covers to the firewall with 2 screws 
LN 5084, washers LN 5165 and nuts LN 5167.
Before assembly, place -
8048.8 cover, -8060.8 
sealing and rubber insert 
-8061.8 on the pipe.
After connecting the pipe, 
tighten both covers on the front 
firewall.
Secure cap nut after 
tightening with 
lashing wire.
Insert hollow screw through the 
drain pipe and fix it to the 
exhaust case threading. On both 
sides of the pipe (on the screw), 
sealing rings (Cu) must be 
placed. After tightening, secure 
the screw with lashing wire.
Sealing rings (Cu) 10x14 CSN 02 9310

### Page 38

No of Sh:
81
Sheet No:
68
Outer combustion liner replacement assembly
Description of Working Steps:
5.45 Check O rings LN 5161 (2 pieces) and LN 5162 (2 pieces), which are on pipes -826.6 and  -
827.6, or replace if necessary.
5.46 At the pressure oil pipe -826.6, clean the contact surfaces (on the side of the pipe to face the 
reduction gearbox) and apply a thin layer of Hylomar. Apply grease to both O-rings (on each 
side of the pipe).. Then, insert the pipe to the cover -8048.8 and put pipes through the opening 
in the fornt firewall and insert the second cover. Insert one end to the accessory gearbox and 
the other to reduction gearbox. Insert sealing -8052.8 on pipe -826.6, insert cover -8053.8, 
sealing -8052.8 and fix the covers to the partition with screws LN 5084, nuts LN 5167 and 
washers LN 5165.
5.47 To the reduction gear box, fix a pipe with two M5 CSN 021401.44 nuts, insert lock washers 5.2 
LMN 3290 under the nuts.   
5.48 Insert a rubber pad on pipe -826.6 and fix the pipe to the flange of the exhaust case and 
centrifugal compressor case. Fix the bottom part of the holder -840.8 to the pipe and both 
parts of the holder with inserted rubber washer pad M601-8073.8 connect with 2 screws LN 
5190 and self-locking nuts LN 5168.
5.49 Assemble the pressure oil pipe to GT -839.6 using cap nuts to the pipe - 826.6 and pressure oil 
bushings -827.9 and secure with lashing wire. 
5.50 To the pipe sucking oil from the reduction gearbox -827.6, insert a cover -8054.6 and insert -
8055.6 and covers connect similarly as in 4.41. Insert one end to the AGB and the other to the 
RGB. Before assembly, coat on the side the contact surface of the pipe flange in Hylomar, and 
Apply grase to both O-rings (on each side of the pipe). . Fix the pipe to the reduction gearbox 
with two nuts MS CSN 02 1401.44, insert lock washers 5.2 LMN 3290 under the the nuts.
Apply a thin layer of grease on 
the end of pipes with the O 
ring and put them in the 
accessory gearbox.
Before pulling            
pipes through the front firewall, slide a cover on them, as well as after 
pulling, before installation of the pipes in the accessory gearbox.

### Page 39

No of Sh:
81
Sheet No:
69
Outer combustion liner replacement assembly
Description of Working Steps:
5.51 Slide insert on the pipe -827.6 and fix the pipe to the holder on the flange of the exhaust 
case and to the centrifugal compressor case using the bottom part of the holder -839.8, 
screw LN 5190 and nut LN 5168 (a rubber pad M601-8072.8 is inserted in the holder). Put 
sealing -827.6 on the pipe.
Tighten the covers M601-8048.8 
and M601-8049.8 with sealings 
and inserts on the front firewall.
According to 5.44, 
assemble the pipe  -
839.6 and secure. 
Clean contact surfaces 
and apply thin layer of 
Hylomar (only the cap 
part).
Fix pipes to the 
flange of the 
exhaust case and 
centrifugal 
compressor case
with holders.
Between covers, insert 
sealing -8052.8 (for 
pipe -826.6) or 8054.9 
(for -827.9) and rubber 
washers -8053.8 (for -
826.6) or 8055.6 on 
the front firewall.

### Page 40

No of Sh:
81
Sheet No:
70
Outer combustion liner replacement assembly
Description of Working Steps:
5.52 In the flange of the exhaust case, insert air intake pipe -880.8. Apply ALHYL paste on the 
flange on the exhaust case before assembling the air pipe for sealing.
Apply ALHYL paste to the contact 
surfaces from both sides.
Insert the pipe in the opening on 
the exhaust case. Make sure the 
pipe is in the right position. 
reduction gearbox.
Apply ALHYL paste to the 
exhaust case flange.

### Page 41

No of Sh:
81
Sheet No:
71
Outer combustion liner replacement assembly
Description of Working Steps:
5.53 To the inflate pipe -828.7, slide cover -8048.8 from the side with O ring, slide the pipe through 
the opening in the front firewall and slide on the other cover -8048.8. Apply thin layer of 
grease to the side of the pipe with the O ring LN 5295 and insert it to the connection of the 
air outlet pipe -108.7 (XM601-159.3 on H-series engines) and secure them.The pipe M601-828.7 
is connected with bolts LN 5444 and Lock Washers 5,2 ONL 3288.2 to the exhaust case and pipe M601-
880.8. Insert gasket M601-8082.8 between the pipe M601-880.8 and pipe M601-828.7. Apply Alhyl to 
all flanges and gasket. Then assemble the inflate pipe -828.7 with the labyrinth inflate pipe PT -
861.9 using cap nut, and secure the nut with lashing wire after tightening. Then, insert, 
between sealing covers -8005.7, rubber insert -8006.7 and sealing -8005.7 on the inflate pipe 
-828.7 and fix them in the opening in the front firewall with covers using LN 5084 nuts and LN 
5167 nuts. Insert washers LN 5165 under the nuts. 
Slide the end of the 
pipe with O ring to 
the air discharge 
pipe. Apply thin 
layer of grease to the 
O-ring.
Apply ALHYL 
paste to the pipe 
contact surface.
After tightening the screws, 
secure lock washers. Then 
connect the PT labyrinth inflate 
pipe using cap nut, and secure 
the nut with lashing wire.
Insert sealing 
covered in 
ALHYL paste 
between the 
inflate pipe and 
the air intake 
pipe.
Between covers in the front firewall,
insert rubber sealing washer and 
tighten the cover screws.

### Page 42

No of Sh:
81
Sheet No:
72
Outer combustion liner replacement assembly
Description of Working Steps:
5.54 On the top part of the exhaust case, mount to 3 -4055.4 screws the front holder (cable 
platform) -848.6 (screws to position 2, 11 20 from the reduction gearbox flange). Applies to 
versions M601E, M601F and GE H-series. 
5.55 To the top part of the exhaust case, assemble 2 -4055.4 screws and the holders of the 
electrical installation platform (screws to position 3 and 13 from the reduction  gearbox 
flange), the other holder connect to the section parting plane on position 6 from the exhaust 
case connection on the right side. Applies to versions M601D and M601Z
Assemble the front 
holder -848.6 
(cable platform) to 
three screws -
4055.4 with 
relevant self-
locking nuts              
-3009.4.
 2
11
20
Assemble the electrical installation platform to two -
4055.4 screws with relevant self-locking nuts -
3009.4 to longitudinal parting plane on the exhaust 
case and one -3007.7 screw with self-locking nut -
3009.7 on the section parting plane.
3
13
6

### Page 43

No of Sh:
81
Sheet No:
73
Outer combustion liner replacement assembly
Description of Working Steps:
5.56 Connect electrical installation and fire detector (if assembled) cables to the front holder -
848.6 (to the cable platform). Applies to M601E, M601F and GE H-series.
5.57 Loosen the pipe to Electro-Hydraulic Actuator -846.9 (when Electro-Hydraulic Actuator is 
installed on the engine) from the propeller governor and electrohydraulical actuator screwing 
and slide electrical installation cable with the propeller heating bus under it. Then reassemble 
the pipe, tighten and secure cap nut with lashing wire on the side of the propeller governor 
and hollow screw on the side of electrohydraulic actuator (at versions with propeller heating).
Release the pipe to 
Electro-Hydraulic 
Actuator, slide the 
propeller heating bus 
cable under it and 
reassemble the pipe. 
Tighten and secure with 
lashing wire the cap nut 
on the propeller 
governor side and the 
hollow screw on the 
electrohydraulic actuator
side.
Connect cables to the front 
holder (cable platform) using 
three connectors.

### Page 44 (OCR)

No of Sh: 81
GE Aviation  Business & General Aviation  Sheet No: 74
Outer combustion liner replacement - assembly
Description of Working Steps:
5.58  To the reduction gearbox flange, assemble, to position 3 and 4 to the left clockwise from the
centring screw fire detector (if assembled) using two self-locking nuts M6 ONL 3248, and
insert washers LN 5275 under them. Fix the cable with holder to the reduction gearbox
flange to position 1.
Assemble fire detector including the holder to
position 3 and 4 using two self-locking nuts M6
and washers LN 5275.
Centring screw
Fix the detector cable to the
reduction gearbox flange to
position 1.
5.59  Lead the cable to the propeller speed transmitter. At engines with Electro-Hydraulic
Actuator, lead it along it and fix it by holders and two longer screws (under two nuts M6
CSN 02 1402.44 with lock washers 6.2 LMN 3290) of electrohydraulic actuator. At engines
without Electro-Hydraulic Actuator, fix the cable to the reduction gearbox flange on
position 1 to the right next to the centring screw and to two screws (under nuts M6 CSN 02
1402.44 with lock washers 6.2 LMN 3290). Insert the connector to the indicator propeller
speed transmitter, tighten and securing with lashing wire. Secure lock washers.

### Page 45

No of Sh:
81
Sheet No:
75
Outer combustion liner replacement assembly
Description of Working Steps:
5.60 If electrohydraulic actuator is part of the engine, insert to it the relevant connector (plug), 
tighten and secure with lashing wire.
5.61 Lead the electrical installation cable to the propeller governor and electromagnetic signaller 
of chips (or to the ELM switch). If Electro-Hydraulic Actuator is part of the engine, lead the 
cable along the pipe to Electro-Hydraulic Actuator -864.9 (two holders). If Electro-
Hydraulic Actuator is not part of the engine, connect the cable to screw 9 on the reduction
gearbox flange from the centring screw. Or assemble the cable according to the original 
assembly.
Secure the connector with lashing 
wire from the drilled flange through 
cap nut to the connector screws.Insert the connector to the 
electrohydraulic actuator.
Lead the cable along the pipe to 
Electro-Hydraulic Actuator -864.9 
to the propeller governor flange.

### Page 46 (OCR)

No of Sh:
81
GE Aviation
Business & General Aviation  Sheet No:
76
Outer combustion liner replacement - assembly
Description of Working Steps:
5.62  Assemble the pipe of the feathering pump -818.6 (if it was assembled). On it, slide the cover
sheet -8048.8, sealing -8058.8 and rubber insert -8059.8 and slide it through the front
firewall. Then slide on the cover sheet M601-8048.8 from the other side and fix and
tighten cap nuts on both sides of the pipe and secure with lashing wire. Insert the electrical
harness between the pipe M601-818.6 and the RGB case before tightening of the pipe.
Install the bolts LN 5084 in the cover sheets and the firewall, install LN 5165 washers and
LN 5167 nuts.
Fix the feathering pump pipe -818.6 and secure with
lashing wire. Before fixing the pipe, slide the electrical
installation cable under it. Fix the cable to the pipe.
Slide cover sheet -8048.8, sealing and rubber insert  Front firewall
on it and slide it through the front firewall, then
Rear firewall
insert cover sheet M601-8048.8 from the other side
After fixing the pipe tighten the cover sheets.
- Sealing (-8058.8)
Rubber insert (-8059.8)

### Page 47

No of Sh:
81
Sheet No:
77
Outer combustion liner replacement assembly
Description of Working Steps:
5.63 Connect the connector to the ELM switch and secure with lashing wire. If ELM is part of the 
engine.
5.64 Assemble the control rod of the propeller governor to the reduction gearbox flange with 
holder and two nuts M6 CSN 02 1402.44 with lock washers 6.2 ONL 3288.1. Secure the nuts 
(if such kind of control is assembled).
Connect the 
connector to the ELM 
switch. Secure the 
connector with 
lashing wire.
Fix the cable to the 
propeller governor.
Assemble the control rod 
to the reduction gearbox 
flange using 2 M6 nuts 
with lock washers. Secure 
the nuts.

### Page 48 (OCR)

No of sh: 81
GE Aviation
Business & General Aviation  Sheet No: 78
Outer combustion liner replacement - assembly
Description of Working Steps:
5.65  Electrical installation cable attach to the feathering pump pipe -818.6, or as it was
attached originally. Then connect, tighten and secure the plug to the propeller governor.
Or connect and tighten plug ELM (if it is part of the engine).
5.66  Fix the remaining cable to the screw according to the picture and then connect and secure
the electromagnetic signaller of chips.
Attach the cable to the feathering
pump pipe (according to the
version, if not already done
pursuant to 4.57).
Connect plug to the propeller
governor and secure it with lashing
wire against loosening.
Connect the cable to the
oil screen screw (can be
connected to the other
screw).
Connect and secure the
electromagnetic
signaller of chips.

### Page 49

No of Sh:
81
Sheet No:
79
Outer combustion liner replacement assembly
Description of Working Steps:
5.67 Assemble propeller regulator control device.
For H80-200 engines: Use the assembly procedure from ASB no. ASB-H80-76-00-00-0047[04], 
all steps from 1.32 till 1.45 for the assembly and adjustment of the Push-Pull Control System
5.62.1 Connect the control case -731.4 to the holder on the outlet system using to LN 5289 
screws. Fix the case so that the holder of the outlet system is under the screw heads, then 
there is insulation -7114.4, then case holder, insulation -7114.4 and -7036.7 liner. Tighten the 
screws using nuts M5 CSN 02 1401.44, insert lock washers 5.2 ONL 3288.2 under them (see 
scheme below). Apply thin layer of mixture of molybdenum sulphide and oil (Molyka) to the 
screw threading. Insert the holder from the torquemeter pipeunder the bottom nut with lock 
washer (at M601E versions).
5.62.2 Connect connecting eye-bending shafts of kinetic connection -703.9 to the double-
lever (double-lever pin) using crown nut -7142.4 and cotter pin LN 5209, and secure it.
5.62.3 Connect control rod of the propeller regulator to the propeer regulator using pin, 
washer and cotter pin, and secure it. 
5.62.2.
5.62.1.
Between the screw 
head and 
insulation, exhaust 
case holder is 
located.
Control case 
holder
Pertinax 
insulation
Liner
5.62.3.

### Page 50

81
Sheet No:
80
Outer combustion liner replacement assembly
Description of Working Steps:
5.68 Assemble the fire extinguishing platform, secure the cap nuts with lashing wire (if 
assembled).
5.69 Check the completeness of the engine.
5.70 Assemble propeller and engine cowlings.
5.71 Add oil to the engine, discharge air from the oil system. Record the executed work in the 
engine log book.
5.72 Verification of the engine function execute with engine test according to the applicable 
EMM, including test flight. 
Assemble the platform to 
the front firewall and the 
extinguishing pipe using 
cap nuts. Secure the nuts 
with lashing wire.
Assemble the platform 
to the holder of the 
fire detector.
Assemble the platform to the 
flange of the reduction gearbox
using the holders on both sides. 
2x2 pieces of M6 nuts and lock 
washers 6.2 ONL 3290.

### Page 51

No of Sh:
81
Sheet No:
81
Outer combustion liner replacement
Verification of the engine function
Description of Working Steps:
6 Verification of the engine function
Execute verification of the engine function by the engine test according to the relevant manual.
Execute the engine test according to the procedures in the following manuals (apart from 
points 7, 10 and 11):
a) For engines GE H80, H80-100, H80-200, H85-100, H85-200, H75-100, H75-200 pursuant to 
sue from 14.Dec.2012.
b) For engines WALTER M601E and M601E- TECHNICAL 
OPERATION OF TURBOPROP ENGINE WALTER M601E, WALTER M601E-21 MANUAL NO. 
0982055
c) For engines WALTER M601E-11, WALTER M601-11S, WALTER M601E-11A, WALTER M601E-
TURBOPROP ENGINE WALTER M601E-11, WALTER M601-11S, WALTER M601E-11A, WALTER 
M601E- 2, 1st EDITION of 
1.7.2008.
d) For engines WALTER M601D-1, WALTER M601D-11, WALTER M601D-11NZ, WALTER M601D-2, 
WALTER M601D-1, WALTER M601D-11, WALTER M601D-11NZ, WALTER M601D-2, WALTER 
9, 1st EDITION from 1.7.2008.
e)
51, 1st edition of 1.7.2008
f) For engines WALTER M601F, WLATER M601F-22 and WALTER M601F-32, manual for assembly 
0982062 WALTER M601F, WALTER M601F-22. WALTER M601F-32, Izdanije 1., data izdanija 
1.7.2008g.
Execute test flight.
                 Record executed work in the engine log book.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
