# GippsAero Mandatory Service Bulletin SB-GA8-2005-23

Copy: Revision 8 ("GippsAero Service Bulletin SB-GA8-2005-23 Issue 8"), 22 pages: PDF https://openairdocs.org/files/sha256/71/b4/71b422306e5592b96b38031ab8547db59956c0068dec12b99891193f92b5dcfc; text https://openairdocs.org/service-documents/gippsaero/sb-ga8-2005-23/file/71b422306e55.md. Rights: © GippsAero. Filed by the FAA in regulations.gov docket FAA-2024-0035; AD 2024-07-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [GippsAero](https://openairdocs.org/service-documents/gippsaero.md)
- Type: Service bulletin (Mandatory Service Bulletin)
- Number: SB-GA8-2005-23
- Latest revision known: SB-GA8-2005-23, Issue 8, dated October 11, 2023 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/gippsaero/sb-ga8-2005-23

## ADs that cite it (3) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2024-07-07](https://openairdocs.org/ad/2024-07-07.md), effective Jun 3, 2024: Revisions 3, 7 and 8
- [AD 2010-18-06](https://openairdocs.org/ad/2010-18-06.md), effective Aug 30, 2010: Revision 3
- [AD 2005-22-02](https://openairdocs.org/ad/2005-22-02.md), effective Nov 17, 2005: Revision 2

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/gippsaero/sb-ga8-2005-23/proposed.md).

## Text (22 pages)

Rights: © GippsAero. Filed by the FAA in regulations.gov docket FAA-2024-0035; AD 2024-07-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

PO Box 881, Morwell, Victoria 3840, Australia   
Ph + 61 (0) 3 5172 1200 
Fax + 61 (0) 3 5172 1201 
www.gippsaero.com.au 
MANDATORY 
Service Bulletin 
SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 1 of 21 
 
SB-GA8-2005-23 
Issue 8 
1 Subject: 
Forward Cargo Door Slide 
2 Applicability: 
Table 1: Aircraft Applicability. 
AIRCRAFT SERIAL NUMBER(s) 
GA8 & GA8-TC 320 All GA8 and GA8-TC 320 Aircraft. 
3 Amendments: 
Issue 1:  Initial Issue. 
Issue 2:  Background amplified. 13 Sep 2005. 
Issue 3:  Service Bulletin was rewritten in total. GippsAero Reference GAE11#843.  
Issue 4:  Inspection of operating rod and requirement for handle with integrated stop added.             
Template updated. GippsAero Reference GAE11#2371. 
Issue 5:  Door handle part number amended, Part C compliance date extended. Typos corrected. 
GippsAero Reference GAE11#2483. 
Issue 6:  Service Bulletin rewritten in total and Part D added. GippsAero Reference GAE11#2415. 
Issue 7:  Part B Revised and formatting updated.  GippsAero Reference GAE11#2808. 
Issue 8:  Revised to improve clarity & compliance schedule.  Refer to change bars. GippsAero Reference 
GAE11#2816. 
4 Background: 
Following in-flight rear cabin door separation s from GA8 and GA8 -TC 320 aircraft, this Service Bulletin 
provides a programme of inspections and upgrades to the door tracks and latching mechanism. 
PART A: Requires installation of a backing plate to forward door slider.  Gives ongoing inspection and 
serviceability criteria of the forward cargo door slide.   
PART B: Provides an inspection and upgrades for the door latch operating rod. 
PART C: Requires installation of a door handle with an integral stop. 
PART D: Requires installation of a physical stop to the forward cargo door slide.

### Page 2

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 2 of 21 
 
5 Compliance: 
Initial and recurring compliance requirements are given below. 
Table 2: Compliance Requirements for SB-GA8-2005-23 
Part Applicability Initial Compliance Recurring Compliance 
A1 All aircraft in Table 1. Within 50 Flight Hours or 2 calendar months, whichever is sooner. - 
A2 All aircraft in Table 1. At next scheduled 100-hourly or annual inspection. At each 100-hourly or annual inspection. 
B1 All aircraft in Table 1. Within 50 Flight Hours or 2 calendar months, whichever is sooner. At each 100-hourly or annual inspection. 
B2 All aircraft in Table 1. When required by PART B1. - 
B3 All aircraft in Table 1. When required by PART B1. - 
C All aircraft in Table 1. Within 150 Flight Hours or 4 calendar months, whichever is sooner. - 
D1 All aircraft in Table 1. Within 50 Flight Hours or 2 calendar months, whichever is sooner. - 
D2 All aircraft in Table 1. When required by PART D1.  - 
6 Weight and Balance: 
There is negligible effect to the weight and balance of the aircraft. 
7 Approval: 
This Service Bulletin has been approved in accordance with the requirements of Australian Civil Aviation 
Safety Regulation 21.095 (1998). 
8 Parts: 
The materials required to complete PART A of this Service Bulletin are detailed in Table 3. 
Table 3: PART A Kit Number SB-GA8-2005-23-01. 
ITEM PART NUMBER DESCRIPTION QTY 
1 GA8-521022-225 Notched Slide-Centre 1 
2 GA8-521022-227 Notched Backing Plate 1 
3 MS24694-S65 Structural Screw 2 
4 AN3-11 Bolt 1 
5 AN960-10L Washer thin 1 
6 AN310-3 Castle nut 1 
7 MS24665-132 Split pin 1 
8 GA8-521022-153 Forward Slide Gauge 1

### Page 3

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 3 of 21 
 
The materials required to complete PART B of this Service Bulletin are detailed in Table 4. 
Table 4: PART B items. 
ITEM PART NUMBER DESCRIPTION QTY 
9 GA8-521012-055 Actuating Rod Assy  1 
9-A GA8-521022-231 Actuating Rod Fitting 2 
9-B GA8-521022-233 Rear Door Rod End, ¼” 2 
9-C NAS601-101 Screw, Machine, Pan Head 6 
9-D MS21042-062 Nut, Self-Locking, Reduced Hex 6 
9-E MS35338-43  Washer, Lock-Spring 3 
9-F AN525-10R11 Screw, Washer Head 1 
 
The materials required to complete PART C of this Service Bulletin are detailed in Table 5. 
Table 5: PART C items. 
ITEM PART NUMBER DESCRIPTION QTY 
10 GA8-521012-0473 Door Handle 1 
11 GA8-521022-159 Handle Bush 1 
 
The materials required to complete PART D1 of this Service Bulletin are detailed in Table 6 and Table 7. 
Table 6: PART D1 Kit Number SB-GA8-2005-23-04. 
ITEM PART NUMBER DESCRIPTION QTY 
12 GA8-521022-221 Centre Rail Aft Stop 1 
13 GA8-521022-223 Radiused Washer 2 
14 MS24694-S6 Structural Machined Screw 2 
15 MS21042-08 Nut, Self-Locking 2 
16 MS24665-132 Split pin 1 
Table 7: Compounds 
ITEM COMPOUND DESCRIPTION 
C1 Silicone Sealant, Silicone, General Purpose, Neutral Cure. 
C2 Duralac Duralac Jointing Compound 
C3 Grease General Purpose Grease, MIL-PRF-81322 or equivalent: Aeroshell Grease 22, Mobil Grease 28, Rheolube 733. 
C4 Loctite 222 Thread locking compound 
C5 Primer MIL-PRF-23377 Type I & II Class C2 
C6 Topcoat Polyurethane topcoat, Colour “Horizon Grey”.   MIL-PRF-85285 Type I Class H or equivalent. 
 
  
 
1 Acceptable alternatives: MS51957-31, MS16995-19, NAS601-12. 
2 Acceptable alternatives: MS21083-N06, AN364-632A 
3 Acceptable alternative: P/No. GA8-521012-051.

### Page 4

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 4 of 21 
 
The materials also required to complete PART D1 of this Service Bulletin, if not completing PART A or 
PART D2, are detailed in Table 8. 
Table 8: PART D additional items. 
ITEM PART NUMBER DESCRIPTION QTY 
1 GA8-521022-225 Notched Slide-Centre 1 
2 GA8-521022-227 Notched Backing Plate 1 
 
9 Parts Availability: 
New parts can be obtained directly from GippsAero. 
Tel: +61 (0)3 5172 1200 
Fax: +61 (0)3 5172 1201 
Email: PARTS@gippsaero.com.au 
10 Labour: 
Table 9 details the approximate time that should be allocated for completing the requirements of each Part 
in this Service Bulletin. 
Table 9: Allocated time for completing each Part. 
PART APPROXIMATE TIME REQUIRED 
A1 30 minutes 
A2 15 minutes 
B1 60 minutes 
B2 60 minutes, if required. 
B3 60 minutes, if required. 
C 45 minutes 
D1 60 minutes 
D2 60 minutes, if required. 
11 Warranty: 
Aircraft under warranty may claim the direct cost of carrying this Service Bulletin via GippsAero Customer 
Service. 
Tel: +61 (0)3 5172 1200 
Fax: +61 (0)3 5172 1201 
Email: Support@gippsaero.com.au

### Page 5

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 5 of 21 
 
12 Accomplishment Instructions: 
GENERAL NOTES: 
Ensure the aircraft is prepared for maintenance and that appropriate safety precautions are taken 
when performing work outlined in this Service Bulletin. 
Unless otherwise specified, reference to the GA8 Service manual as well as FAA AC43.13 -1B 
should be made when carrying out the procedure prescribed in this Service Bulletin.  In case of 
discrepancy between the Service Manual and the AC, the Service Manual takes precedence. 
When carrying out work outlined by this Service Bulletin, care is to be taken to ensure damage to 
surrounding structure and installations does not occur. 
Torque all fasteners in accordance with the GA8 Service Manual unless stated otherwise.  Values 
are for dry (unlubricated) threads unless shown otherwise. 
WARNING: 
IT IS THE RESPONSIBILITY OF ALL PERSONNEL TO ENSURE WORK HEALTH AND 
SAFETY REQUIREMENTS ARE MET AT ALL TIMES. ALL PERSONNEL MUST COMPLY 
WITH ALL WORK HEALTH AND SAFETY REQUIREMENTS AS DEFINED OR 
RECOMMENDED BY: 
- EQUIPMENT OEM INSTALLATION AND OPERATION MANUALS; 
- AIRCRAFT MAINTENANCE AND OPERATION MANUALS; 
- ASSOCIATED AIRCRAFT MODIFICATION INSTRUCTIONS; 
- RELEVANT NAA REGULATIONS AND ADVISORY DOCUMENTATION; 
- ORGANISATION MANUALS, INCLUDING NAA ENDORSED OPERATIONAL 
AND MAINTENANCE MANUALS; AND 
- RELEVANT LOCAL, STATE AND FEDERAL GOVERNMENT REQUIREMENTS.  
WARNING: 
READ THE APPLICABLE MATERIAL SAFETY DATA SHEET (MSDS) FOR ANY 
MATERIAL/CONSUMABLE USED DURING THE ACCOMPLISHMENT OF THIS S ERVICE 
BULLETIN AND EMPLOY ANY RECOMMENDED PERSONAL PROTECTIVE 
EQUIPMENT (PPE) CONTAINED THEREIN.  
 
NOTE: 
Unless stated otherwise, hardware removed during the procedure below is be inspected 
and re-used if serviceable.

### Page 6

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 6 of 21 
 
12.1 PART A1: SLIDER BACKING PLATE INSTALLATION 
1. Open the door handle so that the door swings out to gain access to the Forward Cargo Door Slide 
Assembly, see Figure 1 below. 
 
Figure 1: Forward Cargo Door Slide with door swung open. 
2. Inspect the slide assembly.   If the Backing Plate  (Item 2 of Figure 4) is fitted, no further action is 
required.  If the Backing Plate is NOT fitted, do the remaining steps of this part. 
3. Remove the Forward Cargo Door Slide, by removing the vertical bolt and sliding the slider out of the 
track. On earlier versions of the GA8 aircraft it is necessary to remove the Nylon Track End as shown 
in Figure 2 to be able to remove the slider. 
 
Figure 2: Nylon Track End. 
4. Figure 3 shows how a worn part normally looks and where to measure the groove width.  The TOP 
and BOTTOM profile differs on a worn part and as such both the top and bottom slide grooves are 
to be measured with a calliper. 
 
Figure 3: A worn slider indicating where to measure. 
FORWARD CARGO DOOR SLIDE 
REMOVE THE VERTICAL 
BOLT AND DISCARD.

### Page 7

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 7 of 21 
 
5. Measure the groove width and if the groove is wider than 0.145” at any point along the slider , or if 
the part is cracked or excessively worn, a new slider, Item 1, must be fitted. 
6. Irrespective of Item 1, Items 2 to 7 MUST be fitted as shown in Figure 4 and listed in Table 3. 
  
Figure 4: Old (left) and New (right) Forward Cargo Door Guide Assembly. 
Table 10: Part numbers for the new assembly and the parts it is replacing. 
ITEM 
OLD ASSEMBLY  NEW ASSEMBLY 
QTY 
PART NUMBER DESCRIPTION  PART NUMBER DESCRIPTION 
1 GA8-521022-149 Slide-Centre  GA8-521022-225 Notched Slide-Centre 1 
2 - -  GA8-521022-227 Notched Backing Plate 1 
3 MS24694-S64 Structural Screw  MS24694-S65 Structural Screw 2 
4 AN3-10A Bolt  AN3-11 Bolt 1 
5 AN960-10 Washer  AN960-10L Washer Thin 1 
6 MS21042-3 Nut, Reduced Hexagon  AN310-3 Castle Nut 1 
7 - -  MS24665-132 Split Pin 1 
7. Reinstall the new slider assembly and refit the Nylon Track End if it was removed. Note that the notch 
in Item 1 and Item 2 must be facing aft, refer to Figure 22 of PART D 1 for the correct installed 
orientation.

### Page 8

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 8 of 21 
 
12.2 PART A2: SLIDER WEAR INSPECTION 
1. Open the Rear Cabin Door handle so that the door swings out to gain access to the slider (see PART 
A1, Step 1). 
2. Try to insert the Forward Slide Gauge (Item 8 in Table 3) between the slider and the track as shown 
in Figure 5 and Figure 6 below. Standard Feeler gauges made up to 0.098” 
(0.023”+0.024”+0.025”+0.026”) may also be used. 
 
Figure 5: Checking with the Forward Slide Gauge. Note that all four corners require checking. 
 
Figure 6: Forward Slide Gauge inserted between the slide and track, indicating a worn part. Note track in 
the image has been removed from the aircraft for clarity. Checking can be completed with the track 
installed on the aircraft. 
3. If it is possible to fit the Forward Slide Gauge or feeler gauge between the track and slider (as shown 
in Figure 6 above) at any of the four corners carry out PART A1, Step 2 though 4. 
OR 
4. If Item 8 (or standard feeler gauge) is unavailable, carry out the inspection under PART A1, Step 2 
through 4. 
  
FORWARD SLIDE GAUGE

### Page 9

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 9 of 21 
 
12.3 PART B1: DOOR MECHANISM INSPECTION 
NOTE: 
PARTS B1, B2 and B3 may be done during a single inspection. 
Section B1 inspection must be done on standard operating rods AND those reworked per Section B3.  
1. Remove the Rear Mechanism Cover by removing the screws marked in Figure 7.  
2. With the door handle held fully open / against the stop, check that the operating rod does not touch 
the rear door handle pivot post, refer to Figure 9.  If the rod does touch the pivot post, do PART B2. 
3. Inspect threaded studs and rod ends at both ends of the operating rod as shown in Figure 8. If there 
is any indication of bending: 
i. For actuation rods fitted with female rod ends, do PART B3. 
ii. For actuation rods fitted with male rod ends, replace the parts with new Item(s) 9-B, then 
repeat the inspections and necessary rectification actions detailed in PART B2 and B3.  
4. Check door adjustment as detailed in Section 52-20-10 of the applicable aircraft service manual. 
5. Check that the door ha ndle engages strongly with the catch when in the closed position ( Figure 7).  
Weak engagement may be caused by wear to the handle bush or by damage (bending) of the handle 
and must be corrected by replacing the pivot bush (with Item 11 from Table 5) or the handle (Item 10 
from Table 5) as appropriate. 
6. After finishi ng inspection and required actions, reinstall the Rear Mechanism Cover  as shown in 
Figure 7. 
 
 
Figure 7: Rear Mechanism Cover (latch in closed position). 










AN525-832R6 x2 
GA8-252024-155 
REAR MECHANISM COVER  
DOOR HANDLE MUST 
ENGAGE STRONGLY 
INTO CATCH WHEN 
THE DOOR IS CLOSED 
AND LATCHED.

### Page 10

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 10 of 21 
 
 
Figure 8: Rear Door Handle Mechanism - Inspection Areas. 
 
 
  
INTEGRATED STOP (Marked in Red) OPERATING ROD INSPECTION AREAS

### Page 11

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 11 of 21 
 
12.4 PART B2: DOOR PIVOT REWORK 
1. Disconnect the rod ends from the handle and pivot arm. Remove the forward rod end and pull out 
the operating rod. 
2. Rework the pivot post as detailed in Figure 9. 
3. Install the operating rod through frame bush prior to installing forward Rod End. Install rod ends and 
connect to the handle and pivot arm. 
NOTE: 
Minimum thread engagement to not be less than the rod end check hole. 
Perform functional check to ensure the door operates correctly 
4. Adjust door mechanism as detailed in Section 52-20-10 of the applicable aircraft service manual. 
5. After finishing inspection and required actions, reinstall the Rear Mechanism Cover  as shown in  
Figure 7. 
  
VIEW A (NOT TO SCALE) 
 
Figure 9: Rear Door Handle Pivot Post – Rework Area. 
  



Notes: 
1. Only Pivot post shown for clarity. 
2. Rework using blending guidelines of 
AC43.13-1B Chapter 6 Section 7 and 10. 
3. Ensure rod end and rod have a minimum 
clearance of 0.040in from pivot post. 
4. Restore surface protection IAW Service 
Manual using compound C5 (Table 7). 
CHECK FOR CLEARANCE 
BETWEEN OPERATING ROD / 
ROD END AND PIVOT POST 
Operating Rod 
PIVOT POST 
INTEGRATED STOP 
(Marked in Red)

### Page 12

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 12 of 21 
 
12.5 PART B3: DOOR OPERATING ROD REWORK 
1. Disconnect the existing rod ends from the handle and pivot arm. Remove the forward rod end and 
pull out the operating rod. 
2. Replace with a new assembly, Item 9 of Table 4, OR, Ø0.313 rod assemblies may be reworked as 
detailed in the following steps. 
i. Cut 0.625 inches (15.9 mm) from each end of the existing Operating Rod. 
ii. Temporarily fit the Rod, Fittings (Item 9-A) and rod ends (Item 9-B) to the door as shown in 
Figure 10. 
iii. Rotate the fittings so that the screws are vertical, as shown in Figure 10.  Match-drill the 
rod to the Fittings (Item 9-A). Drill size #28 (0.1405 in). 
iv. Install screws, trim any excess thread below nuts and de-burr.  Ensure 1.5 full threads 
extend beyond the nut. 
v. Remove Fittings (Item 9-A) from the rod.  Apply compound C1 and do the final assembly of 
the AFT Fitting (Item 9-A) as shown in Figure 10.  
3. Install the operating rod through frame bush.  Do this before installing FWD Fitting (Item 9-A). 
4. Assemble FWD Fitting (Item 9-A) and rod end (Item 9 -B) as shown in Figure 10, then connect the 
rod as detailed in Figure 11 and Figure 13.  Check for clearance and make any required adjustments 
as detailed in Figure 14 to Figure 16. 
5. If needed, the Pivot Arm may be modified in accordance with Figure 14. 
6. If needed, the door skin may be modified in accordance with Figure 15. 
7. If needed, increase cut-out size in interior trim as shown in Figure 16. 
8. Once sufficient clearance is achieved, do the final assembly of the Fitting (Item 9-A), using compound 
C1 (Table 7) as shown in Figure 10. 
9. Install rod ends (Item 9-B) and connect to the handle and pivot arm as shown in Figure 11 (for P/No. 
GA8-521012-047 Door Handle) Figure 12 (for P/No. GA8-521012-051 Door Handle) and Figure 13, 
using the original hardware or Items 9-E and 9-F as required. 
10. Do the inspection detailed in Section B2 and, if needed, rework the pivot post ( Figure 9). 
11. Adjust door as detailed in Section 52-20-10 of the applicable aircraft service manual. 
NOTE: 
Minimum thread engagement to not be less than the rod end check hole. 
Perform functional check to ensure the door operates correctly 
12. After finishing inspection and required actions, reinstall the Rear Mechanism Cover  as shown in  
Figure 7. 
   
Figure 10: Rod End Fitting Installation FWD (Left) and AFT (Right).  Some parts omitted for clarity.  
EACH SCREW: ITEMS 9-C AND 9-D. 
EACH ROD END: ITEM 9-B.

### Page 13

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 13 of 21 
 
 
Figure 11: AFT Rod End Installation – P/No. GA8-521012-047 Door Handle 
 
Figure 12: AFT Rod End Installation – P/No. GA8-521012-051 Door Handle 
 
 
Figure 13: FWD Rod End Installation 
AN525-10R12 
MS35338-43 x 3 
AN960-10L 
MS21042-3 
AN3-7A 
AN960-10 
MS21042-3 AN960-10 
P/No. GA8-521012-047 
DOOR HANDLE 
P/No. GA8-521012-051 
DOOR HANDLE 
AN525-10R11 
MS35338-43 x 2 
AN960-10L 
MS21042-3 
AFTER ASSEMBLY, CHECK C LEARANCE 
BETWEEN SCREW AND DOOR SKIN. 
AFTER ASSEMBLY, CHECK C LEARANCE 
BETWEEN SCREW AND DOOR SKIN.

### Page 14

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 14 of 21 
 
 
Figure 14: Pivot Arm Clearance 
 
  
Figure 15: Door Skin Clearance 
DETAIL VIEW A
A
Notes: 
1. Only Pivot Arm shown for clarity. 
2. Rework using blending guidelines of 
AC43.13-1B Chapter 6 Section 7 and 10. 
3. Ensure rod end and rod have a minimum 
clearance of 0.040 in from pivot  arm. 
4. Restore surface protection IAW Service 
Manual using compounds C5 and C6 
(Table 7). 
SKIN SECTION INDICATED 
MAY BE REMOVED IN LINE 
WITH THE ROD END. 
Notes: 
1. Some parts omitted for clarity. 
2. Rework using blending guidelines of 
AC43.13-1B Chapter 6 Section 7 and 10. 
3. Removal of mounting hardware for the 
pivot arm is required. 
4. It is recommended to insert a thin steel 
item – such as a razor blade – between 
the skin and the frame to prevent 
damage to the frame. 
5. Restore surface protection IAW Service 
Manual using compounds C5 and C6 
(Table 7). 
DOOR FRAME 
DOOR SKIN

### Page 15

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 15 of 21 
 
 
Figure 16: Door Trim Clearance 
 
 
 
 
 
  
ENSURE MINIMUM 0.080” 
CLEARANCE BETWEEN 
ROD ASSEMBLY AND 
DOOR TRIM.

### Page 16

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 16 of 21 
 
12.6 PART C: DOOR HANDLE INSPECTION 
1. Remove Rear Mechanism Cover, refer to Figure 7.  
2. Inspect rear door handle for integrated stop (bent over tab), refer to Figure 8 and Figure 9. Replace 
door handles without an integrated stop with Item 10 from Table 5.  Use a sufficient amount of grease 
(compound C3 of Table 7) on the handle shaft. 
NOTE: 
Install screw to outer door handle with compound C4 (Table 7). 
3. Check for excessive play in the handle. If required, replace the handle bush with Item 11 from Table 
5. 
4. Adjust door as detailed in Section 52-20-10 of the applicable aircraft service manual. 
5. If a new handle has been fitted, carry out a Door Mechanism Inspection in accordance with PART 
B1. 
6. Reinstall the Rear Mechanism Cover, refer to Figure 7.

### Page 17

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 17 of 21 
 
12.7 PART D1: TRACK STOP INSTALLATION 
1. Inspect the aircraft to see if a centre rail aft stop is fitted  (Figure 22).  If a stop is fitted, no further 
action is required.  If a stop is NOT fitted, do the remaining steps of this part. 
2. Remove enough interior trim panels  and insulation to gain access to the area identified  by the blue 
square in Figure 17. 
 
Figure 17: Removal of interior trim and insulation. View looking at the interior structure of the aircraft's 
port side fuselage wall. 
3. Remove the Rear Door Pivot Hinge Fairing identified in Figure 18. 
 
Figure 18: Removal of the Rear Door Pivot Hinge Fairing. View looking at the exterior surface of the 
aircraft’s port side fuselage wall. 
 
4. Drill out the NAS1097AD4 countersunk rivet  (MS20470AD4 universal rivet for early aircraft serial 
numbers), identified by the red circle in Figure 19, and enlarge the hole to a diameter between 0.165” 
(4.2mm) and 0.169” (4.3mm).

### Page 18

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 18 of 21 
 
 
Figure 19: Location of rivet to drill out. View looking at the exterior surface of the aircraft’s port side 
fuselage wall. 
5. Drill a hole 2.000”, below the rivet location drilled out in PART D1, Step 3, as illustrated in Figure 20. 
The diameter of the hole should be between 0.165” (4.2mm) and 0.169” (4.3mm).  The lower hole 
existing in the Centre Rail Aft Stop (P/N: GA8 -521022-221) can be used as a guide to mark this 
location. 
 
Figure 20: Maximum permissible trimming of the Centre Cargo Door Rail (GA8-521022-023). All 
dimensions are in inches. 
6. Trial fit the Centre Rail Aft Stop. If the centre tapered feature of the component overlaps with the 
Centre Cargo Door Rail, it is permissible to trim (or notch) the aft end of the Centre Cargo Door Rail 
to the maximum dimension shown by the red trim line in Figure 20 (i.e. 0.188” forward of the Centre 
Rail Aft Stop attachment holes). If trimming the of Centre Cargo Door Rail is to be conducted in situ, 
it is recommended that a thin piece steel sheet is placed between the fuselage skin and the Centre 
Cargo Door Rail, to protect the aircraft’s structure during trimming. 
7. If the Centre Rail Aft Sto p does not fit over the Centre Cargo Door Rail  side walls, try clamping the 
side walls to return them perpendicular with the aircraft’s fuselage wall. If this is not possible, refer to 
the “Parts Availability” section of this Service Bulletin for contact details to order a replacement Centre 
Cargo Door Rail (P/N: GA8-521024-023). 
8. Wet install the Centre Rail Aft Stop (P/N: GA8 -521022-221) using two (2) off MS24694 -S6 screws, 
two (2) off Radiused Washers (P/N: GA8-521022-223) and two (2) of MS21042-08 nuts as per Figure 
21. A sufficient amount of anti-corrosive joining compound (Item C1 in Table 7) should be applied to 
the faying surfaces of the Centre Rail Aft Stop component the Left Hand Side Wall Skin (GA8 -
535021-037). Refer to Section 20-10-20 of the GA8 Service Manual for recommended torque values.

### Page 19

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 19 of 21 
 
 
Figure 21: Installation of the Centre Rail Aft Stop (P/N: GA8-521022-221) component. View looking at the 
interior structure of the aircraft's port side fuselage wall. 
9. Replace the existing Slide-Centre (P/N: GA8-521022-149) and Backing Plate ( if fitted, P/N: GA8-
521022-151) with the Notched Slide -Centre (P/N: GA8 -521022-225) and Notched Backing Plate  
(P/N: GA8-521022-227). Alternatively, if the existing Slide -Centre and Backing Plate components 
are in an acceptable condition, they may be modified to include the notched feature as per PART 
D2. Figure 22 shows the correct orientation in which the Forward Cargo Door Guide Assembly should 
be installed. Note that a replacement split pin is included in the SB -GA8-2005-23-04 kit (refer to 
Table 6). 
10. Assemble the centre rail slider assembly using the New Assembly configuration detailed in Figure 4 
and Table 10. 
 
Figure 22: Correct orientation of the Forward Cargo Door Guide Assembly. View looking at the exterior 
surface of the aircraft’s port side fuselage wall. 
11. Perform a functional check of the Rear Cabin Door to ensure that opening and closing of the door is 
unobstructed.  Check door adjustment as detailed in Section 52 -20-10 of the applicable aircraft 
service manual. 
12. Reinstall the Rear Door Pivot Hinge Fairing removed in PART D1, Step 2. 
13. Reinstall any insulation and interior trim panels removed in PART D1, Step 1.

### Page 20

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 20 of 21 
 
12.8 PART D2: DOOR SLIDER REWORK TO SUIT TRACK STOP 
NOTE: 
If the existing Slide-Centre (P/N: GA8-521022-149) component does not satisfy the requirements of 
PART A2, the slider is in an unacceptable condition and must not be used. 
1. Modify an existing Slide-Centre (P/N: GA8-521022-149) component in accordance with Figure 23. 
 
 NOTES: 
a. NOT TO SCALE 
b. Unless otherwise stated, all dimension are in inches. 
c. Tolerances: Unless otherwise stated all dimensions are ± 0.005” [0.13mm]  
d. De-burr sharp edges. 
e. Using indelible ink, permanently part mark the Modified Slide-Centre component as         
SB-521022-225. 
Figure 23: Machining of an existing Slide-Centre (P/N: GA8-521022-149) to form Modified Slide-Centre 
(P/N: SB-521022-225). 
 
2. Modify an existing Backing Plate (P/N: GA8-521022-151) component in accordance with Figure 24. 
 
 NOTES: 
a. NOT TO SCALE 
b. Unless otherwise stated, all dimension are in inches. 
c. Tolerances: Unless otherwise stated all dimensions are ± 0.005” [0.13mm] 
d. De-burr sharp edges. 
e. Apply primer to the machined area that conforms to MIL-PRF-23377K (or a later approved 
revision) or FEDSPEC-TT-P-1757B (or a later approved revision). Apply topcoat of white 
paint that conforms to MILPRF-85285E (or later approved revision). 
f. Using indelible ink, permanently part mark the Modified Backing Plate component as      
SB-521022-227. 
Figure 24: Machining of an existing Backing Plate (P/N: GA8-521022-151) to form Modified Backing 
Plate (P/N: SB-521022-227). 
  
A
DETAIL A
B
DETAIL B

### Page 21

SB-GA8-2005-23 Issue 8 Date of Issue:  11th Oct 2023 Page 21 of 21 
 
  
13 Documentation: 
Update the aircraft logbook to reflect incorporation of Issue 8 of this Service Bulletin. The logbook should 
state what sections have been incorporated (i.e. PART D1, PART D1 & D2 or PART A1 & D1).  
 
14 Continuing Airworthiness: 
Periodic inspection requirements for the rear cabin door are detailed in Section 5. 
15 Compliance Notice: 
Complete the Document Compliance Notice and return to GippsAero by mail, fax or email.

### Page 22

DOCUMENT COMPLIANCE NOTICE 
 
Document: 
SB-GA8-2005-23 
Issue 8 
 
 
Aircraft Serial Number: GA8-______________ 
The following parts of Service Bulletin SB-GA8-2005-23 Issue 8 have been incorporated in the 
above aircraft (tick as appropriate). 
 
☐ PART A 
☐ PART B 
☐ PART C 
☐ PART D 
Date of Incorporation: ________________  
 __________________________________  
 Signed 
Print Name: ________________________  
Please post, fax or email this compliance notice to: 
GippsAero Technical Services 
P.O. Box 881 
Morwell Victoria 3840 
Australia 
Fax.: +61 03 5172 1201 
Email:  TECHPUBS@gippsaero.com.au

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
