# GippsAero Service Bulletin SB-GA8-2017-174

Copy: Revision 2 ("SB-GA8-2017-174 Issue 2"), 20 pages: PDF https://openairdocs.org/files/sha256/2d/93/2d9359d4ab63f7c21fe80bb92de9bee3aa9e4483c3b3f5f4330ffc57bc359ee0; text https://openairdocs.org/service-documents/gippsaero/sb-ga8-2017-174/file/2d9359d4ab63.md. Rights: © GippsAero. Filed by the FAA in regulations.gov docket FAA-2018-0771; AD 2019-07-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [GippsAero](https://openairdocs.org/service-documents/gippsaero.md)
- Type: Service bulletin (Service Bulletin)
- Number: SB-GA8-2017-174
- Latest revision known: SB-GA8-2017-174, Issue 2, dated May 23, 2018 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/gippsaero/sb-ga8-2017-174

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2019-07-08](https://openairdocs.org/ad/2019-07-08.md), effective May 23, 2019: Revision 2

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/gippsaero/sb-ga8-2017-174/proposed.md).

## Text (20 pages)

Rights: © GippsAero. Filed by the FAA in regulations.gov docket FAA-2018-0771; AD 2019-07-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

PO Box 881, Morwell,  Victoria 3840, Australia   
Ph + 61 (0) 3 5172 1200 
Fax + 61 (0) 3 5172 1201 
www.mahindraaerospace.com 
MANDATORY 
Service Bulletin 
SB-GA8-2017-174 Issue 2 Date of Issue:   23-May-2018 Page 1 of 18 
Issue 2 
SB-GA8-2017-174 
Issue 2 
Subject 
Wing Strut and Strut Fitting Inspection and Replacement 
Applicability 
This Service Bulletin is applicable to the serial numbers listed for the part numbers identified in Table 1. 
Critical part serial numbers can have five (5) or six (6) digits, with a prefix of either ‘00’ or ‘000’. Note 
Table 1 only lists the last three (3) or four (4) relevant numbers. 
Table 1 – Applicability 
PART NUMBER PART SERIAL NUMBERS 
GA8-570026-035 
Strut 
Struts delivered on new aircraft: 350 thru 361, 363 thru 398, 402 thru 406, 409 
thru 440, 442 thru 449, 451, 452, 459, 461, 462, 465, 466 thru 483, 486 thru 497, 
500 thru 503, 506, 507, 510 thru 515, 520 thru 523, 526 thru 533, 552 thru 554, 
559, 560, 562 
 
Struts provided as replacement items: 362, 399, 400, 484, 498, 499, 512, 513, 
524, 525, 527, 538, 539, 542, 543, 544, 545, 546, 547 
GA8-570026-029 
Strut Fitting – Fuselage End 718 thru 808, 889 thru 1022 
GA8-570026-031 
Strut Fitting – Wing End 716 thru 806, 967 thru 1020 
GA8-571022-105  
Forward Strut Fitting, RH 289, 290, 296, 297, 299, 300, 301, 308 thru 320, 322, 323, 325 thru 347  
GA8-571022-106 
Forward Strut Fitting, LH 
288, 289, 290, 292, 295, 298, 303, 306 thru 314, 316 thru 319, 321 thru 326, 329 
thru 333, 335 thru 345 
GA8-571022-107 
Aft Strut Fitting, LH 307 thru 346 
GA8-571022-108 
Aft Strut Fitting, RH 308 thru 347 
GippsAero records show the aircraft serial numbers listed in Table 2 are affected, however all Operators 
must check the individual serial numbers identified in Table 1 as the following list may be incomplete. 
Table 2 – Known Affected Aircraft 
AIRCRAFT AIRCRAFT SERIAL NUMBERS 
GA8 and GA8-TC 320 Aircraft 139 Aircraft 158 thru 239 inclusive 
Amendments 
Issue 1:  Initial Issue, released 26-Feb-2018 
Issue 2:  Amends requirement for strut removal for inspections to be  a one-off only, inspection Part C1 
and C2  are combined . Recurring o n-wing inspections  introduced for Wing and Strut Fittings ; 
outlined in Part C3 . Table 3 updated to include Part C3 . References to Service Letter SL-GA8-
2018-37 included where relevant.  Rework of interfacing fuselage lug. Other minor changes 
highlighted by vertical change bars.

### Page 2

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 2 of 18 
Issue 2 
Background 
GippsAero has recently id entified that some P/N GA8 -570026-035 Struts, P/N GA8 -570026-029 Strut 
Fitting – Fuselage End, P/N GA8 -570026-031, Strut Fitting – Wing End, and P/N GA8571022 -105,-106,-
107 and -108 Strut Fittings cannot be assured as meeting their material specification requirements. This 
Service Bulletin introduces inspection requirements and replacement instructions for identified Wing 
Struts and Fittings. Safe flight with the identified Wing Strut Assemblies  and Strut Fittings can continue as 
their certified strength is unaffected , however there ma y be a reduction in the Strut and Strut Fitting 
fatigue lives. As a precaution GippsAero is mandating replacement of Struts and Strut Fittings as detailed 
in this Service Bulletin.  
Compliance 
This Service Bulletin requires an initial general visual inspection by 31 st August 2018; recurring general 
visual inspections are required at intervals not exceeding 110 hours.  This Service Bulletin requires a one-
off detailed visual inspection, that involves the strut removal, by 31st August 2018; then recurring on-wing 
visual inspections are required at 1000 hours intervals. This Service Bulletin also introduces new 
mandatory replacement times for affected parts. More detail is provided under Continuing Airworthiness 
on Page 4. 
Weight and Balance 
The inspections outlined herein do not impact the aircraft’s weight and balance. 
A single replacement Strut Assembly, P/N GA8 -570016-041, adds 1.4 lbs to the aircraft 52 ” aft of the 
datum. 
Approval 
The airframe inspection described in this  Service Bulletin  and part replacement intervals have been 
approved pursuant to Australian Civil Aviation Safety Regulation 21.098 (1998). GippsAero Reference 
GAE11#2215. 
Labour 
- 2 man hours should be allocated for completing the work detailed in Part B of this Service 
Bulletin.  
- 3 man hours should be allocated for completing the work detailed in Part C1 and C2 of this 
Service Bulletin. 
- 3 man hours should be allocated for completing the work detailed in Part C3 of this Service 
Bulletin. 
- 5 man hours should be allocated for completing the work detailed in Part D of this Service 
Bulletin. 
- 5 man hours should be allocated for completing the work detailed in Part E of this Service 
Bulletin. 
These estimates do not include time required to do normal maintenance preparation or set up equipment. 
Spare Parts and Warranty 
Replacement Wing Strut Assemblies and Wing Strut Fittings can be obtained by contacting  GippsAero 
Customer Service: 
Tel: +61 (0)3 5172 1200 
Fax: +61 (0)3 5172 1201 
Email: aircraft.parts@mahindraaerospace.com 
Aircraft covered by warranty may claim the direct cost of incorporating the requirements of this Service 
Bulletin by contacting GippsAero Customer Service: 
Tel: +61 (0)3 5172 1200 
Fax: +61 (0)3 5172 1201 
Email: aircraft.warranty@mahindraaerospace.com

### Page 3

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 3 of 18 
Issue 2 
Part Identification 
The parts affected by this Service Bulletin are identified in Figure 1. 
 
Figure 1 – Part Identification 
LHS Shown, RHS Opposite

### Page 4

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 4 of 18 
Issue 2 
Continuing Airworthiness 
The requirements of this Service Bulletin are shown in Table 3. 
Table 3 – Service Bulletin Requirements 
SERVICE 
BULLETIN 
APPLICABILITY 
See Table 1 for Serial 
Number effectivity 
ACTION and 
DESCRIPTION STARTS INTERVAL TERMINATES 
 
PART A All Identification of affected parts - - -  
PART B All General visual inspection by 31st August 2018 100 +/-10 hours when parts replaced by   Part D or Part E  
PART C1 
and 
PART C2 
GA8-571022-105  
Forward Strut Fitting, RH 
One-off detailed 
non-destructive 
inspection 
 
by 31st August 
2018 
 
N/A 
 
when inspection 
performed 
 
GA8-571022-106 
Forward Strut Fitting, LH 
 
GA8-571022-107 
Aft Strut Fitting, LH 
 
GA8-571022-108 
Aft Strut Fitting, RH 
 
GA8-570026-029 
Strut Fitting – Fuselage End 
 
GA8-570026-031 
Strut Fitting – Wing End 
 
PART C3 
GA8-571022-105  
Forward Strut Fitting, RH 
Detailed non-
destructive 
inspection 
by 31st August 
2018 
1000 +/- 10 
hours 
 when parts 
replaced by   
Part D 
 
GA8-571022-106 
Forward Strut Fitting, LH 
 
GA8-571022-107 
Aft Strut Fitting, LH 
 
GA8-571022-108 
Aft Strut Fitting, RH 
 
GA8-570026-029 
Strut Fitting – Fuselage End Detailed non-
destructive 
inspection 
by 31st August 
2018 
1000 +/- 10 
hours 
 when parts 
replaced by   
Part E 
 
GA8-570026-031 
Strut Fitting – Wing End 
 
PART D 
GA8-570026-035 
Strut Replacement 
Not exceeding 9,000 part hours in service  
OR 
within 5 calendar years of date of issue of this 
Service Bulletin whichever occurs first 
 
GA8-570026-029 
Strut Fitting – Fuselage End 
Replacement 
Not exceeding 6,000 part hours in service  
nOR 
within 3 calendar years of date of issue of this 
Service Bulletin whichever occurs first 
 
 
GA8-570026-031 
Strut Fitting – Wing End 
 
PART E 
GA8-571022-105  
Forward Strut Fitting, RH 
Replacement 
Not exceeding 6,000 part hours in service  
OR 
within 3 calendar years of date of issue of this 
Service Bulletin whichever occurs first 
 
GA8-571022-106 
Forward Strut Fitting, LH 
 
GA8-571022-107 
Aft Strut Fitting, LH 
 
GA8-571022-108 
Aft Strut Fitting, RH

### Page 5

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 5 of 18 
Issue 2 
Table 4 shows the non -destructive inspection requirements for a typical block of 1000 flight hours after 
the date of issue of this Service Bulletin. 
Table 4 – Inspection requirements 
 Inspection Type  
Aircraft Hours in Service General Visual  (Part B) One-Off  Detailed Visual  (Part C1 and C2) On Wing Detailed Visual  (Part C3)  
By 31st August 2018    
+100     
+200     
+300     
+400     
+500    
+600    
+700    
+800    
+900    
+1000    
Part B and Part C3 inspections must continue until any of the parts identified in Table 1 reach the 
replacement times shown in Table 3.

### Page 6

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 6 of 18 
Issue 2 
Parts 
The spare parts that may be required to do Parts C1 and C2 or C3 for one Strut Assembly are listed  in 
Table 5. 
Table 5 – Parts C1 and C2 or C3      (KIT SB-GA8-2017-174-1) 
ITEM PART NUMBER DESCRIPTION QTY ALTERNATE  
1 NAS6610-38 BOLT, HEX HEAD, CLOSE TOLERANCE 2 -  
2 AN960-1016 WASHER, PLAIN 2 NAS1149G1063P NAS1149F1063P  
3 MS21245L10 NUT, SELF LOCKING, HEXAGON 2 MS21083N10  
4 AN316-10R NUT, JAM 2 NASM316-10R  
 
The spare parts required to do Part D for one Strut Assembly are listed in Table 6. 
Table 6 – Part D      (KIT SB-GA8-2017-174-2) 
ITEM PART NUMBER DESCRIPTION QTY ALTERNATE  
5 NAS6610-38 BOLT, HEX HEAD, CLOSE TOLERANCE 2 -  
6 AN960-1016 WASHER, PLAIN 2 NAS1149G1063P NAS1149F1063P  
7 MS21245L10 NUT, SELF LOCKING, HEXAGON 2 MS21083N10  
8 AN316-10R NUT, JAM 2 NASM316-10R  
9 GA8-570016-041 STRUT ASSEMBLY 1 -  
 
The spare parts required to do Part E for one wing are listed in Table 7. 
Table 7 – Part E       (KIT SB-GA8-2017-174-3 and -4) 
ITEM PART NUMBER DESCRIPTION QTY – LH WING (-3) QTY – RH WING (-4) ALTERNATE 
10 GA8-571022-106 FORWARD STRUT FITTING, LH 1 - - 
11 GA8-571022-107 AFT STRUT FITTING, LH 1 - - 
12 GA8-571022-105 FORWARD STRUT FITTING, RH - 1 - 
13 GA8-571022-108 AFT STRUT FITTING, RH - 1 - 
14 AN5-15A BOLT, MACHINE, AIRCRAFT 1 1 - 
15 AN5-16A BOLT, MACHINE, AIRCRAFT 1 1 - 
16 AN5-17A BOLT, MACHINE, AIRCRAFT 1 1 - 
17 AN5-20A BOLT, MACHINE, AIRCRAFT 2 2 - 
18 AN960-516 WASHER, PLAIN 9 9 NAS1149G0563P NAS1149F0563P 
19 MS21042-5 NUT, SELF LOCKING 5 5 - 
20 NAS6610-38 BOLT, HEX HEAD, CLOSE TOLERANCE 2 2 - 
21 AN960-1016 WASHER, PLAIN 2 2 NAS1149G1063P NAS1149F1063P 
22 MS21245L10 NUT, SELF LOCKING, HEXAGON 2 2 - 
23 AN316-10R NUT, JAM 2 2 NASM316-10R

### Page 7

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 7 of 18 
Issue 2 
Approved Non-Destructive Inspections 
Parts C1, C2 and C3 of this Service Bulletin require mandatory visual inspections of primary aircraft 
structure. These visual inspections assess the condition of the parts and their paint or primer coatings. 
They also look for corrosion, scratches, scoring, dents or cracks in machined parts and the wing strut. 
All mandatory visual inspections require the use of at least 10x magnification and a strong supplementary 
source of light. A borescope (or Videoscope) is required for the On-Wing inspection in Part C3.   
This Service Bulletin also identifies Eddy Current Inspection (ECI) or fluorescent Liquid Penetrant 
Inspection (LPI) as approved alternate procedures for the inspections. Where a non -destructive 
inspection is required by this Service Bulletin, GippsAero will identify general industry standards for either 
ECI or LPI if used as approved alternatives to the mandatory visual inspection. These industry standard s 
can be used by any local non -destructive testing provider to develop inspection  techniques specific to the 
relevant parts. 
Names of Features on Strut Fittings 
Examples of t he names of geometric features and locations on the  Strut Fittings are shown in Figure 2. 
When doing the visual inspections required by this Service Bulletin, all of these features and locations 
must be examined and these names should be used when communicating the results of any inspections 
to GippsAero. 
 
 
Figure 2 – Strut Fitting Feature Names

### Page 8

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 8 of 18 
Issue 2 
Accomplishment Instructions 
All of the following accomplishment  instructions are applicable to either the Left Hand Side (LHS) or the 
Right Hand Side (RHS) of the aircraft, unless noted otherwise.  
WARNING: 
IT IS THE RESPONSIBILITY OF ALL PERSONNEL TO ENSURE WORK 
HEALTH AND SAFETY REQUIREMENTS ARE MET AT ALL TIMES. ALL 
PERSONNEL MUST COMPLY WITH ALL WORK HEALTH AND SAFETY 
REQUIREMENTS AS DEFINED OR RECOMMENDED BY: 
- AIRCRAFT MAINTENANCE AND OPERATION MANUALS; 
- RELEVANT NAA REGULATIONS AND ADVISORY DOCUMENTATION; 
- ORGANISATION MANUALS, INCLUDING NAA ENDORSED 
OPERATIONAL AND MAINTENANCE MANUALS; AND 
- RELEVANT LOCAL, STATE AND FEDERAL GOVERNMENT 
REQUIREMENTS. 
WARNING: 
READ THE APPLICABLE MATERIAL SAFETY DATA SHEET (MSDS) FOR ANY 
CONSUMABLE USED DURING THE ACCOMPLISHMENT OF THIS SERVICE 
BULLETIN AND EMPLOY ANY RECOMMENDED PERSONAL PROTECTIVE 
EQUIPMENT (PPE) CONTAINED THEREIN. 
NOTE: 
Unless otherwise specified, reference to the GA8 or GA8-TC 320 Service Manual 
and FAA Advisory Circular (AC) 43.13-1B & -2B should be made when carrying out 
the procedures prescribed in this Service Bulletin.  In case of a discrepancy 
between the Service Manual and the AC, the Service Manual takes precedence.  
Part A – Preparation  
1. Put the aircraft on a stable, level surface such as inside a maintenance hangar.  
2. Make the aircraft safe for maintenance by at least electrically isolating the aircraft by disconnecting 
the aircraft battery.  
3. Apply the aircraft park brake or otherwise chock at least the main landing gear wheels. 
4. Remove Strut to Fuselage and Strut to Wing fairings. Retain fasteners if serviceable.  
5. Slide fairing(s) away from Strut attachment joint(s). 
CAUTION: 
CROSS CHECK PHYSICAL PART IDENTIFICATION AND AIRCRAFT LOG 
BOOK CAREFULLY IF STRUT ASSEMBLIES HAVE BEEN PREVIOUSLY 
REPLACED DURING AIRCRAFT SERVICE. 
IF PHYSICAL PART IDENTIFICATION IS NOT POSSIBLE, OR A 
DISCREPANCY EXISTS BETWEEN PHYSICAL PART AND AIRCRAFT 
LOGBOOK, CONTACT GIPPSAERO 
6. Identify and record the Wing Strut part number and serial number. Verify the aircraft’s log book 
contains the correct information. 
7. Identify and record the Strut Fitting – Wing End and Strut Fitting – Fuselage End part numbers and 
serial numbers. Verify the aircraft’s log book contains the correct information. 
8. Identify and record the Forward and Aft Strut Fitting part numbers and serial numbers. Verify the 
aircraft’s log book contains the correct information.

### Page 9

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 9 of 18 
Issue 2 
Part B – Directed Detailed Visual Inspection 
All of the following accomplishment instructions are applicable to either the Left Hand Side (LHS) or the 
Right Hand Side (RHS) of the aircraft, unless noted otherwise. 
CAUTION: 
THIS SECTION OF THE SERVICE BULLETIN DOES NOT AUTHORISE ANY 
REWORK. IF YOU THINK REWORK MAY BE REQUIRED, CONTACT 
GIPPSAERO 
NOTE: 
Removal of the Wing Strut Assembly from the aircraft will not be required 
1. Clean the inspection areas identified in Figure 3 using a cleaning solvent or airframe cleaning 
compound. 
2. Do a detailed visual inspection, using at least 10x magnification and a strong light source  of the 
areas of the Strut, Strut Fittings (Wing End and Fuselage End) and Strut Fittings (Forward and Aft) 
in Figure 3. Look for cracked or damaged surface protection (primer and paint), corrosion or other 
damage. 
 
 
Figure 3 – Directed Detailed Visual Inspection Areas 
3. If any indications of cracking or corrosion are found, remove paint from the inspection area and do 
another detailed visual inspection. 
4. If any indications of cracking or corrosion are found, replace all affected parts in accordance with 
Part D or Part E of this Service Bulletin. Contact GippsAero for assistance if required. 
5. If no cracks or corrosion are found, do a torque check of all the fasteners connecting the Strut 
Fittings to the Strut using values from Chapter 20 of the GA8/GA8-TC 320 Service Manual. If any 
fasteners are found loose, contact GippsAero for assistance. Otherwise, continue.  
6. If any areas of paint are removed for inspection, or found to be damaged, restore the surface 
protection. Apply a chemical conversion coating, Type 1, Class 1A per MIL-DTL-5541. Apply a 
coat of primer that conforms to MIL-PRF-23377 or FED-SPEC-TT-P-1757. Apply a topcoat of paint 
that conforms to MIL-PRF-85285 and matches the surrounding colour. 
NOTE: 
Surface protection is very important and helps prevent corrosion. Make sure to 
restore any removed or damaged surface protection.   
use a mirror to inspect fitting 
and inside surfaces of the strut   
use a mirror to inspect fitting 
and inside surfaces of the strut

### Page 10

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 10 of 18 
Issue 2 
7. Install Strut to Fuselage and Strut to Wing fairings, inspection is complete.  
Part C – Detailed Non-Destructive Inspection 
All of the following accomplishment instructions are applicable to either the Left Hand Side (LHS) or the 
Right Hand Side (RHS) of the aircraft, unless noted otherwise. 
The inspections required by this section of the Service Bulletin are:  
- one-off inspection that removes the Strut and performs detailed visual inspections of Part C1 and C2 
- recurring On-Wing detailed visual inspections in Part C3 that removes the Strut bolts at 1000 hour 
intervals 
CAUTION: 
THIS SECTION OF THE SERVICE BULLETIN AUTHORISES LIMITED REWORK. IF 
ADDITIONAL REWORK IS REQUIRED, CONTACT GIPPSAERO 
Part C1 and Part C2 – Preparation 
1. Shore aircraft wing by placing on trestles or similar supporting device in accordance with Chapter 
7-20-00 of the GA8/GA8-TC 320 Service Manual. Service Letter SL-GA8-2018-37 also provides 
additional guidance on how to shore the wing, remove the bolts and remove the Strut. 
2. Remove upper and lower Strut bolts, nuts and washers. 
3. Remove Wing Strut from aircraft. 
4. Clean bolts, nuts and washers using a cleaning solvent. Inspect the bolts, nuts and washers for 
serviceability.  
Look for corrosion, scores, scratches or any other damage. Look for damaged surface protection 
(Cadmium plating). Check that the locknut has a minimum prevailing torque of 1 8 in-lbs. 
Bolt hole diameter standard value: 0.623” – 0.624” 
If corrosion is evident or Cadmium plating is compromised, or if the hardware is not within above 
limits, replace the affected hardware with new parts as listed in Table 5.  
Part C1 – Forward and Aft Strut Fittings (Wing) Inspection 
1. Clean wing Forward and Aft Strut Fittings attached to the wing identified in Figure 4 using a 
cleaning solvent or airframe cleaning compound. 
2. Do a detailed visual inspection using at least 10x magnification and a strong light source of the lug 
faces, inner surfaces of the Strut Fitting bolt holes, fastener lands and Fitting shank.  
Look for corrosion, cracks, scores, scratches or any other damage. Look for cracked or damaged 
surface protection (primer and paint). Check lug bolt holes for any evidence of elongation, damage 
or corrosion.  
Bolt hole diameter standard value: 0.6245” – 0.6255” 
If corrosion or cracks are found, or if the bolt hole is not within the standard value, replace all 
affected parts in accordance with Part E of this Service Bulletin. Contact GippsAero for assistance 
if required.  
Otherwise, continue. 
NOTE: 
Doing an Eddy Current Inspection of the bolt holes in accordance with 
SAE-ARP-4402 is an approved alternative method of inspection for these parts 
Doing a fluorescent liquid penetrant inspection in accordance with 
ASTM E-1417 is an approved alternative method of inspection for these parts 
3. If any areas of paint are removed for inspection, or found to be damaged, restore the surface 
protection. Apply a chemical conversion coating, Type 1, Class 1A per MIL-DTL-5541. Apply a 
coat of primer that conforms to MIL-PRF-23377 or FED-SPEC-TT-P-1757. Where required, apply 
a topcoat of paint that conforms to MIL-PRF-85285 and matches the surrounding colour. 
NOTE: 
Surface protection is very important and helps prevent corrosion. Make sure to 
restore any removed or damaged surface protection.

### Page 11

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 11 of 18 
Issue 2 
 
             
Figure 4 – Inspection areas in Strut Fittings (Forward and Aft) 
 
Part C2 - Wing Strut Fittings and Fuselage Attachment Inspection 
1. Clean the inspection areas of the Strut and all Strut Fittings identified in Figure 5 and interfacing 
parts on the fuselage using a cleaning solvent or airframe cleaning compound. 
2. Do a detailed visual inspection using at least 10x magnification and a strong light source of the lug 
faces, inner surfaces of the Strut Fitting bolt holes, lug clevis and fastener lands  and interfacing 
parts on the fuselage.  
Look for corrosion, cracks, scores, scratches or any other damage. Look for cracked or damaged 
surface protection (primer and paint). Check lug bolt holes for any evidence of elongation, damage 
or corrosion.  
Bolt hole diameter standard value: 0.625” – 0.627” 
If corrosion or cracks are found, or if the Strut Fitting bolt hole/s is/are not within the standard 
value, replace the Strut Assembly in accordance with Part D of this Service Bulletin. Contact 
GippsAero for assistance if required.  
NOTE: 
Doing an Eddy Current Inspection of the bolt holes in accordance with 
SAE-ARP-4402 is an approved alternative method of inspection for these parts  
Doing a fluorescent liquid penetrant inspection in accordance with 
ASTM E-1417 is an approved alternative method of inspection for these parts

### Page 12

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 12 of 18 
Issue 2 
 
Figure 5 – Wing Strut and Strut Fittings inspection areas 
3. If there is evidence of foul on the strut fitting lug inner face and fuselage lug outer faces, remove 
material from the fuselage lug by blending as shown in Figure 6. 
 
 
Figure 6 – Allowable Rework to Fuselage Lug 
 
RIB 5/6   
Note:  
Finish the blended edge s with 
an abrasive pad or similar to 
achieve a maximum surface 
roughness of 63 Ra

### Page 13 (OCR)

TAPER REGION
DETAIL C  0.250
(SHORT STRAP)
CHAMFER 45° TO 0.040  90
TAPER
REGION
0.500
60°
SECTION A-A
DETAIL B
SHORT STRAP
0.040 -  0.040
Note:
Finish the blended edges with  BLEND TO MATCH
an abrasive pad or similar to  STRAP PROFILE
achieve  a  maximum surface
roughness of 63 Ra  0.050  0.040
0.040-
OUTER DOUBLER
DETAIL B
Figure 6 - Allowable Rework to Fuselage Lug - Continued
SB-GA8-2017-174  Issue 2  Date of Issue: 23-May-2018  Page 13 of 18
Issue 2

### Page 14

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 14 of 18 
Issue 2 
4. Restore the surface protection of any areas of paint are removed for inspection/rework, or found to 
be damaged. Apply a chemical conversion coating, Type 1, Class 1A per MIL -DTL-5541. Apply a 
coat of primer that conforms to MIL-PRF-23377 or FED-SPEC-TT-P-1757. Where required, apply 
a topcoat of paint that conforms to MIL-PRF-85285 and matches the surrounding colour. 
5. Apply a thin coat of general purpose airframe grease to the mating surfaces of the Strut Fittings. 
Install removed Wing Strut using serviceable bolts, nuts and washers Items 1, 2, 3 and 4. Remove 
any excess grease from the threads of the Bolt and torque the AN316 nut to between 55 and 65 
lb.ft. 
 
Part C3 – On-Wing Forward and Aft Strut Fittings (Wing), Strut and Strut Fitting Inspection  
These inspections require a borescope/videoscope inspection of the Strut Fitting lug bolt holes that can 
be done without removing the Strut Assembly. 
1. Shore aircraft wing by placing on trestles or similar supporting device in accordance with Chapter 
7-20-00 of the GA8/GA8-TC 320 Service Manual. Service Letter SL-GA8-2018-37 also provides 
additional guidance on how to shore the wing, remove the bolts and remove the Strut.  
2. Remove upper Strut bolt, nuts and washers. Inspect the removed hardware for serviceability as 
described in Part C1 and Part C2 – Preparation Step 4. 
NOTE: 
Remove one bolt at a time. 
CAUTION: 
MAKE SURE WING AND STRUT WILL NOT MOVE BEFORE INSERTING ANY 
OBJECT INTO THE LUG BOLT HOLES 
3. Clean the inspection areas of the Strut, visible external areas of Strut Fittings and the Strut Fitting 
lug bolt holes using a cleaning solvent or airframe cleaning compound. Work carefully in the lug 
bolt holes and remove all foreign objects. 
4. Do a detailed visual inspection using at least 10x magnification and a strong light source of the 
visible external surfaces of the Strut Fittings. 
Do a detailed visual inspection of the inside of the lug bolt holes using a borescope /videoscope.  
Look for corrosion, cracks, scores, scratches or any other damage. Look for cracked or damaged 
surface protection (primer and paint). Check lug bolt holes for any evidence of elongation, damage 
or corrosion.  
Bolt hole diameter standard value: 0.625” – 0.627” 
If corrosion or cracks are found, perform Part C1 / C2 inspection. If the bolt hole/s is/are not within 
the standard value, replace the unserviceable part(s) in accordance with Part D (for the Strut 
Assembly) or Part E (for the Wing Strut Fittings) of this Service Bulletin  as required . Contact 
GippsAero for assistance if required. 
Otherwise, continue. 
5. Apply a thin coat of a general purpose airframe grease to the mating surfaces of the Strut Fittings . 
Install serviceable or new bolt, nuts and washers (Items 1, 2, 3 and 4 of Table 5). Remove any 
excess grease from the threads of the Bolt and torque the AN316 nut to between 55 and 65 lb.ft.  
6. Remove lower Strut bolt, nuts and washers. Inspect the removed hardware for serviceability as 
described in Part C1 and Part C2 – Preparation Step 4 
7. Perform Part C3 steps 3 through 4 on the lower Strut fitting.  
8. Apply a thin coat of general purpose airframe grease to the mating surfaces of the Strut Fittings. 
Install serviceable or new bolt, nuts and washers (Items 1, 2, 3 and 4 of Table 5). Remove any 
excess grease from the threads of the Bolt and torque the AN316 nut to between 55 and 65 lb.ft.

### Page 15

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 15 of 18 
Issue 2 
Part D – Strut Assembly Replacement 
Table 1 identifies Struts, Strut Fitting s – Wing End and Strut Fitting s – Fuselage End that 
require replacement as outlined in Continuing Airworthiness on Page 4. 
If any Strut Assembly has any of affected parts listed in  Table 1, replace the entire Strut 
Assembly. 
NOTE: 
If the Wing Strut Fittings also require replacement, do Part E at the same time 
as Part D. 
If Wing Strut Fittings do not require replacement, or do require replacement but 
are not being replaced at this time, do Part C1 at the same time as Part D. 
1. Remove Strut to Fuselage and Strut to Wing fairings. Retain fasteners if serviceable.  
2. Slide fairing(s) away from Strut attachment joint(s). 
3. Shore aircraft wing by placing on trestles or similar supporting device in accordance with Chapter 
7-20-00 of the GA8/GA8-TC 320 Service Manual. Service Letter SL-GA8-2018-37 also provides 
additional guidance on how to shore the wing, remove the bolts and remove the Strut. 
4. Remove and discard all upper and lower Strut bolts, nuts and washers. 
5. Remove Strut Assembly from aircraft. 
6. Remove Strut to Fuselage and Strut to Wing fairings from Strut Assembly and retain if serviceable. 
7. If inspection has found corrosion or other forms of damage, contact GippsAero to determine if the 
removed Strut Fittings must be returned to GippsAero for further assessment . 
8. Put Strut to Fuselage and Strut to Wing fairings on new Strut Assembly.  
NOTE: 
Take care when installing Fairings. Do not damage the Strut Assembly. 
9. Apply a thin coat of general purpose airframe grease to the mating surfaces of the Strut Fittings. 
Install new Strut Assembly, Item 9, in reverse order using Items 5, 6, 7 and 8. Remove any excess 
grease from the threads of the Bolt and torque the AN316 nut to between 55 and 65 lb.ft. 
10. If required, do a Wing Rigging check in accordance with Chapter 57-10-10 of the GA8/GA8-TC 
320 Service Manual.

### Page 16

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 16 of 18 
Issue 2 
Part E – Wing Strut Fitting Replacement 
Table 1 identifies wing Strut Fittings that require replacement as outlined in Continuing 
Airworthiness on Page 4. 
1. Shore aircraft wing by placing on trestles or similar supporting device in accordance with Chapter 
7-20-00 of the GA8/GA8-TC 320 Service Manual. Service Letter SL-GA8-2018-37 also provides 
additional guidance on how to shore the wing, remove the bolts and remove the Strut.  
2. Remove and discard all upper and lower Strut bolts, nuts and washers. 
3. Remove Wing Strut from aircraft. 
4. Remove wing access panels as shown in Figure 7 to access wing Strut Fittings. 
 
Figure 7 – Wing Access Panels 
5. Remove and discard all wing Strut Fittings bolts, nuts and washers.  
6. Remove wing Strut Fittings. If inspection has found corrosion or other forms of damage, contact 
GippsAero to determine if the removed Strut Fittings must be returned to GippsAero for further 
assessment.  
7. Do a detailed visual inspection using at least 10x magnification and a strong light source of the 
Front Spar under the Strut Fittings.  
Look for corrosion, cracks, scores, scratches or any other damage. Look for cracked or damaged 
surface protection (primer and paint). Check the fastener holes for any evidence of elongation, 
corrosion or damage.  
Wing Front Spar bolt hole diameter standard value: 0.3125” – 0.3130” 
If damage is found on the Front Spar, or the bolt holes are outside the standard value, contact 
GippsAero for assistance. Otherwise, continue. 
8. If any areas of paint are removed for inspection, or found to be damaged, restore the surface 
protection. Apply a chemical conversion coating, Type 1, Class 1A per MIL-DTL-5541. Apply a 
coat of primer that conforms to MIL-PRF-23377 or FED-SPEC-TT-P-1757. If applicable apply a 
topcoat of paint that conforms to MIL-PRF-85285 and matches the surrounding colour. 
NOTE: 
Surface protection is very important and helps prevent corrosion. Make sure 
to restore any removed or damaged surface protection.

### Page 17

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 17 of 18 
Issue 2 
8. Use a strut bolt to align the Strut Fitting ‘big end’ lug bolt holes. Temporarily locate the Strut 
Fittings and check that fastener holes in the Fitting and the Front Spar are aligned.  
NOTE: 
The Strut Fitting and Front Spar fastener holes are aligned if the bolts can be 
installed with light pressure. 
Check that there is clearance between the Forward and Aft Strut Fittings and the Front Spar 
flanges on the forward and aft sides of the Spar in the area shown in Figure 8. 
 
Figure 8 – Clearance check 
Forward shown, aft side the same 
9. If there is no clearance between the Wing Strut Fitting and the Front Spar flange(s), remove 
material from the edge of the Front Spar flange(s) by blending as shown in Figure 9.  
 
Figure 9 – Allowable rework to Front Spar flange(s) edge 
Do not exceed a maximum depth of 0.040” and finish the blended edge with an abrasive pad or 
similar to achieve a maximum surface roughness of 63 Ra.  
10. Apply a chemical conversion coating, Type 1, Class 1A per MIL-DTL-5541, to any reworked area 
of the Front Spar. Apply a coat of primer that conforms to MIL-PRF-23377 or FED-SPEC-TT-P-
1757. If applicable apply a topcoat of paint that conforms to MIL-PRF-85285 and matches the 
surrounding colour.

### Page 18

SB-GA8-2017-174 Issue 2 Date of Issue:  23-May-2018 Page 18 of 18 
Issue 2 
11. Install new wing Strut Fittings and fasteners as shown in Figure 10 wet with the anti-corrosive, 
chromated jointing compound Duralac. Torque all nuts to between 100 and 140 in-lbs. 
 
Figure 109 – Strut Fitting Installation  
(Balloons show item number from Table 7) 
12. Apply a thin coat of a general purpose airframe grease to the mating surfaces of the Strut Fittings. 
Install Strut Assembly in reverse order using Items 20, 21, 22 and 23. Remove any excess grease 
from the threads of the Bolt and torque the AN316 nut to between 55 and 65 lb.ft. 
13. If required, do a Wing Rigging check in accordance with Chapter 57-10-10 of the GA8/GA8-TC 
320 Service Manual. 
 
Documentation 
Update aircraft log book to reflect incorporation of this Service Bulletin.  
Compliance Notice 
Complete the Document Compliance Notice and return to GippsAero by mail, fax or email.

### Page 19

DOCUMENT COMPLIANCE NOTICE 
 
Document: 
SB-GA8-2017-174 
Issue 2 
 
 
Aircraft Serial Number:  GA8-______________ 
Please record any actions done to any of the part numbers listed in this Service Bulletin and return to 
GippsAero by mail, fax or email. 
 Inspection Type     
Part Number Part B Part C1/C2 Part C3 Part Replaced Hours in Service  
GA8-570026-035      
GA8-570026-029       
GA8-570026-031       
GA8-571022-105       
GA8-571022-106      
GA8-571022-107      
GA8-571022-108      
Please note the results of any inspections (i.e. nothing found, evidence of corrosion, cracking 
indication): 
Part Number Inspection Result 
GA8-570026-035 
GA8-570026-029 
GA8-570026-031 
GA8-571022-105 
GA8-571022-106 
GA8-571022-107 
GA8-571022-108 

### Page 20

DOCUMENT COMPLIANCE NOTICE 
 
Document: 
SB-GA8-2017-174 
Issue 2 
 
 
Service Bulletin SB-GA8-2017-174, Issue 2 has been incorporated in the above aircraft  and/or Strut 
serial number. 
Date of Incorporation: _____________________  
Signed: ________________________ Print Name: ____________________________  
   
 
 
Please post, fax or email this compliance notice to: 
GippsAero Technical Services 
P.O. Box 881 
Morwell Victoria 3840 
Australia 
Fax.:  +61 03 5172 1201 
Email: aircraft.techpubs@mahindraaerospace.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
