# Grimes Aerospace Service Bulletin 10-1571-33-0041

Copy: No revision named ("FAA-2017-0906_Grimes SB 10-1571-33-0041"), 12 pages: PDF https://openairdocs.org/files/sha256/d9/7a/d97a04092eb67a6f05315a585389ca140723c55ca4bc1e69e992d7e07ec3fa14; text https://openairdocs.org/service-documents/grimes/sb-10-1571-33-0041/file/d97a04092eb6.md. Rights: © Grimes Aerospace. Filed by the FAA in regulations.gov docket FAA-2017-0906; AD 2018-07-21 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Grimes Aerospace](https://openairdocs.org/service-documents/grimes.md)
- Type: Service bulletin (Service Bulletin)
- Number: 10-1571-33-0041
- Page: https://openairdocs.org/service-documents/grimes/sb-10-1571-33-0041

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2018-07-21](https://openairdocs.org/ad/2018-07-21.md), effective May 21, 2018: No revision named
- [AD 2005-12-16](https://openairdocs.org/ad/2005-12-16.md), effective Jul 20, 2005: No revision named

Also cited in [2 proposed ADs](https://openairdocs.org/service-documents/grimes/sb-10-1571-33-0041/proposed.md).

## Text (12 pages)

Rights: © Grimes Aerospace. Filed by the FAA in regulations.gov docket FAA-2017-0906; AD 2018-07-21 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

GRIMES  SERVICE
AEROSPACE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
PLANNING INFORMATION
a.  EFFECTIVITY
This service bulletin describes the procedures to modify the 10-1571-(SERIES)
Passenger Service Unit (PSU), to prevent moisture from contributing to
electrical shorting and or failure of the PSU. These recommended changes
will be incorporated into new production PSU with serial number 1000 and
subsequent.
b.  REASON
Excessive moisture may cause shorting of the connectors J1 or J2 and
terminals of transformers T1, 12 or T3.
C.  DESCRIPTION
Incorporation of this service bulletin and associated kit, will insulate these
components from moisture that could result in electrical shorting and failure
of the PSU. After incorporation of this Service Bulletin the change will be
identified with revision "C".
a.  COMPLIANCE
Incorporation of this service bulletin is recommended, specifically in known
locations where heavy moisture / condensation has been reported, around
or  near the PSU.
e.  APPROVAL
This service bulletin contains no modification information that revises the
approved configuration and therefore does not require government or other
regulatory agency approval.
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV.  DATE __  _ FIGURE NO..  PAGE NO. 1 ~ 12

### Page 2 (OCR)

GRIMES  SERVICE
AEROSPACE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
PLANNING INFORMATION---(CONTINUED)
MANPOWER
The estimated manhours required to accomplish the modifications contained
in this service bulletin are as follows:
Disassembly  0.05 hours
Modification  0.33 hours
Assembly  0.10 hours
Test  0.10 hours
Total  0.58 hours
g.  MATERIAL, COST AND AVAILABILITY
Grimes Modification Kit 10-1624-1 may be procured from :
Grimes Aerospace Company
Product Support Group
240 Twain Avenue
Urbana, OH 43078 USA
Telephone: 513-653-5225
Fax:  513-652-2322
SITA:  DAYFLCR
The price of Grimes Modification Kit 10-1624-1 is $ 5.45 for all orders
shipped on or before 12/31/93. After this date the price is subject to change.
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV.  _ DATE  _ FIGURE NO.  PAGE NO. _  2

### Page 3 (OCR)

GRIMES  AEROSPACE  SERVICE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
PLANNING INFORMATION---(CONTINUED)
MATERIAL, COST AND AVAILABILITY-.-(CONTINUED)
The following additional customer furnished materials or EQUIVALENT are
required to incorporate these changes.
(1) ADHESIVE / SEALANT, SILICONE RUBBER SEALANT, NO. 3145
Dow Corning Corp, Midland Michigan.
n.  TOOLING - Not Applicable
i.  WEIGHT AND BALANCE - None
ELECTRICAL LOAD DATA - Not Affected
SOFTWARE ACCOMPLISHMENT SUMMARY - Not Applicable
REFERENCES
GRIMES DRAWING 10-1571, REV C, PASSENGER SERVICE UNIT
GRIMES DRAWING 10-1624, KIT, MODIFICATION
COMPONENT MAINTENANCE MANUAL 33-20-64
m.  OTHER PUBLICATIONS AFFECTED
None
n.  FAMILY TREE CHARTS OF MODIFICATION RELATIONSHIPS
Not Applicable
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV. _  _ DATE _  _ FIGURE NO. _  PAGE NO.3

### Page 4 (OCR)

GRIMES  SERVICE
AEROSPACE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
ACCOMPLISHMENT INSTRUCTIONS---(See Figure 1)
CAUTION
PLEASE USE ELECTRO-STATIC DEVICE (ESD) PRECAUTIONS
1.  DISASSEMBLY
NOTE:  Place a soft cloth on the bench before proceeding with disassembly.
Position the LENS side of the PSU face down on the cloth, to protect the
lens side of PSU from damage.
A. (Fig. 1) Unplug connector J2 of lead wire assembly (110) from the mating
connector of access cover assembly (60). Loosen four (captive), ¼ turn
fasteners, to "partially" free the access cover assembly from the mounting
plate assembly (280).
CAUTION:
Use care with the handling of access cover assembly as it will still be attached
electrically to mounting plate assembly by way of electrical wires to the circuit
card assembly (CCA) and mounting plate assembly.
B. (Fig. 1) Disconnect connector J3 of lead wire assembly (185), from the
(Fig. 2) mating connector (75) J3 on (Fig. 1) CCA (45A).
C. (Fig. 1) Remove six screw assemblies (55) holding CCA (45A) to access
cover assembly (60).
D. Remove CCA (45A) from access cover assembly (60).
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV.  DATE __  FIGURE NO.  PAGE NO.  4

### Page 5 (OCR)

GRIMES  AEROSPACE  SERVICE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
ACCOMPLISHMENT INSTRUCTIONS---(CONTINUED)
2.  MODIFICATION... (See Figure 2 and 3)
NOTE:
Use extreme care in all handling and modification procedures, to avoid
damage to any electrical component.
A. (Fig. 2) Examine the board-mounted mating connectors J1 and J2 of CCA
(45A), for foreign objects and or broken / bent pins inside connector.
Clean CCA and replace connector it necessary.
B. (Fig. 3) Remove from the Kit, gaskets (65A) and (70A).
C. (Fig. 3) Install gasket (65A), inside connector (J1), carefully compressing
the gasket over the pins, so that both halves of each pin are visible after
installation of gasket. Repeat this identical procedure for gasket (70A),
installing gasket (70A) inside connector (J2).
CAUTION
Area should be well ventilated before applying adhesive / sealant.
D. (Figs. 2 and 3) Using a syringe (or similar application device), apply
silicone rubber adhesive / sealant over the pins of transformers (115)
T1, T2, and T3, per Figure 3.
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV.  DATE _  FIGURE NO.  PAGE NO.

### Page 6 (OCR)

GRIMES  AEROSPACE  SERVICE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
ACCOMPLISHMENT INSTRUCTIONS---(CONTINUED)
2.  MODIFICATION... (CONTINUED) (See Figure 2 and 3)
Apply sealant to form a radius, approximately 0.063 inches
(1.6 mm), along bottom edges of connectors J1 and J2.
NOTE:  This material cures in any position but should not be disturbed after
5 - 10 minutes of application. Allow 24 hours for full cure.
ASSEMBLY---(See Figure 1)
A. (Fig. 1) Carefully position CCA (45A) in access cover assembly (60) and
secure CCA with six screw assemblies (55).
B. Install connector (185) of lead wire assembly to the mating connector J3
on the CCA. Carefully position access cover assembly (60) in place and
then secure access cover assembly using the four (captive), ¼ turn
fasteners.
C. Install connector of lead wire assembly (110) to mating connector J2 of
access cover assembly (60).
D. Stamp or mark, with permanent ink, "REV C" and "MODIFIED PER
SB10-1571-33-0041" on the access cover assembly (60).
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV.  DATE _  FIGURE NO.  PAGE NO.

### Page 7 (OCR)

GRIMES  SERVICE
AEROSPACE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
ACCOMPLISHMENT INSTRUCTIONS---(CONTINUED)
4.  TESTING---(See Figure 4)
NOTE:  For the following tests, DC ground should be connected to earth
ground for maximum touch switch sensitivity.
A. Apply + 28 volts to pin 1 of connector J1 and ground pin 9.
B. The three lamps in "NO SMOKING" sign shall illuminate.
C. Remove the ground lead from pin 9 and connect it to pin 12.
D. The three lamps in "Fasten Seat Belt" sign shall illuminate.
E. Apply 115 VAC, 400 Hz, between pins 2 and 3 of connector J1 and
+ 28 VDC to pin 1 and DC ground to pin 4.
F. Sequentially touch the reading light touch plates. The two or three reading
lights, as applicable, shall illuminate.
G. Touch the call touch plate. The attendant call light shall illuminate.
With an oscilloscope connected to pin 5, a momentary chime signal shall
be present.
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV.  _ DATE FIGURE NO.  PAGE NO.

### Page 8 (OCR)

GRIMES  SERVICE
AEROSPACE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
ACCOMPLISHMENT INSTRUCTIONS---(CONTINUED)
4.  TESTING---(CONTINUED) (See Figure 4)
H. Momentarily apply ground (use DC ground) to J1-pin 7. All reading
lights shall illuminate. Repeat this step to turn off lights.
. Test complete. Disconnect 115 VAC, 400 HZ from pins 2 and 3 of
connector J1 and + 28 VDC from pin 1 and DC ground from pin 4.
MATERIAL INFORMATION
FIG  ITEM  NEW  QTY  PRICE  KEY WORD  OLD  INSTRUCTIONS
NO.  NO.  PART NUMBER  PART NUMBER  DISPOSITION
20  NONE  N/A  LENS  25-1301-()  RETAIN
1, 2  45A  NONE  N/A  CIRCUIT CARD ASSY  11-5341-()  MODIFY
1  55  NONE  6  NA  SCREW ASSY  NAS1301-4-4  RETAIN
1  60  NONE  1  ACCESS CVR. ASSY  11-5339-()  RETAIN
185  NONE  1  N/A  LEAD WIRE ASSY  11-5337-()  RETAIN
280  NONE  N/A  MTG PLATE ASSY  11-5328-()  RETAIN
2, 3  65  NONE  1  N/A  CONNECTOR J1  CO-7636  RETAIN
2,3  65A  60-4940-3  1  ***  GASKET (KIT)  NONE  INSTALL
2,3  70  NONE  1  NA  CONNECTOR J2  CO-7622  RETAIN
2,3  70A  60-4940-1  1  **7  GASKET (KIT)  NONE  INSTALL
2,3  115  NONE  3  N/A  XMFR. T1,12,13  55-1085-1  RETAIN
REF  N/A  10-1624-1  EA  $5.45  KIT, MOD  NONE  INSTALL
NOTE: ITEMS WITH THE ***, ARE COMPONENTS OF THE KIT AND ARE NOT SEPARATELY PRICED.
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV.  DATE _  FIGURE NO. -  PAGE NO.  8

### Page 9 (OCR)

GRIMES  AEROSPACE  SERVICE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
33¢
225A
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV. — DATE FIGURE NO.  PAGE NO.

### Page 10 (OCR)

GRIMES  SERVICE
AEROSPACE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
-35
135-
—115
K3
•35
130-
10-
15
70A
65.  -35
65A
20-
-115
35
125~
-35
75~
-105
-35
25  II0A 95,100
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV.  DATE  FIGURE NO. 2  PAGE NO.

### Page 11 (OCR)

GRIMES  AEROSPACE  SERVICE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
J2
• Sealant (7 Places)
- 60-4940-1  - 60-4940-3
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV.  _ DATE _  _ FIGURE NO. _  3  PAGE NO.

### Page 12 (OCR)

GRIMES  AEROSPACE  SERVICE
BULLETIN
PASSENGER SERVICE UNIT
GRIMES PART NUMBER 10-1571-(SERIES)
FOKKER 100
300
CALL
7 ON
IISVAC  400Hz  AC GNO  NO SMOKING  OPTIONAL  SPKR  TEST  GNO
Electrical Schematic Diagram
DATE 10/15/93 TITLE: PASSENGER SERVICE UNIT
10-1571-33-0041
REV.  _ DATE _  FIGURE NO.4  PAGE NO.  12

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
