# Grob Service Bulletin 1078-186/2: No revision named

- Rights: © Grob. Filed by the FAA in regulations.gov docket FAA-2013-0013, the docket of AD 2013-08-04. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Grob Service Bulletin 1078-186/2](https://openairdocs.org/service-documents/grob/sb-1078-186-2.md)
- Title as filed: U.S. DOT/FAA - 1078-186_2 MSB, Inspection of elevator  trim tab arm Rev.2
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/53/ec/53ecdadbfb4f4f0ee5b47cf217487504b15f83ae85e4eec420da2c5c5f78b25c
- Page: https://openairdocs.org/service-documents/grob/sb-1078-186-2/file/53ecdadbfb4f

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

MSB1078-186/2 
Page  1 of 6 
28 March 2012 
Replaces Issue: 08. Mar 2012  
  
 
1078-186_2 MSB, Inspection of elevator  trim tab arm Rev.2  G 115E/EG 
 
Grob Aircraft AG, Lettenbachstrasse 9, D-86874 Tussenhausen-Mattsies 
SERVICE BULLETIN NO. MSB1078-186/2 
I. TECHNICAL DETAILS  
1.1 Category:  
 
Mandatory 
 
1.2 Airplanes affected:  
 
G 115E all S/N  
G 115EG all S/N 
 
1.3 Time of Compliance:  
 
Part A: Next 50 hours inspection or next regular inspection whichever comes first , before receipt 
of material for terminating action. 
Note: Replacement of an affected trim tab arm in accordan ce with the instructions of 
MSB 1078-186 at original issue is acceptable to com ply with Part A of this Service 
Bulletin. 
 
Accomplishment of MSB 1078-186/1 is acceptable to c omply with Part A of this 
Service Bulletin. 
 
Part B: Terminating action: Next 50 hours inspection or next regular inspection whichever 
comes first, after receipt of material.  
 
1.4 Subject:  
 
ATA-Code: 55-20 Elevators and Trim tab 
  Inspection of elevator trim tab arm 
 
1.5 Reason:  
 
Grob received a report from a fleet operator that an elevator trim tab arm P/N 115E-3758 was 
found cracked from a rear mounting hole (either L/H or R/H) to the rear edge of the trim tab arm.

### Page 2

MSB1078-186/2 
Page  2 of 6 
28 March 2012 
Replaces Issue: 08. Mar 2012  
  
 
1078-186_2 MSB, Inspection of elevator  trim tab arm Rev.2  G 115E/EG 
 
Grob Aircraft AG, Lettenbachstrasse 9, D-86874 Tussenhausen-Mattsies 
 
Fig. 1 
 
Dye penetrant check of defective items revealed, that a visual inspection of an installed item 
mandated with MSB1078-186 at original issue may not be sufficient to detect every crack on the 
bracket (Fig. 2).  
 
 
Fig. 2 
 
Therefore a dye penetrant check or more significant NDT of the dismounted parts has been 
mandated by MSB1078-186/1  to  ensure safe operation until the terminating action will be  
accomplished. 
 
Investigation of defective parts revealed corrosion cracking as cause for cracks. To prevent 
future cracking, the Trim Tab Arm 115E-3758 is replaced by 115E-3758/1, which is 
manufactured from an alloy resistant to corrosion cracking. In addition to that, shaping is 
improved and a paint coat is applied.  
 
1.6 Concurrent documents:  
 
G 115E:   AMM TR No. 05-21 
G 115EG: AMM / JG TR No. 05SMC-03, 05SMC-04, 05GV-0 4 
Location of crack

### Page 3

MSB1078-186/2 
Page  3 of 6 
28 March 2012 
Replaces Issue: 08. Mar 2012  
  
 
1078-186_2 MSB, Inspection of elevator  trim tab arm Rev.2  G 115E/EG 
 
Grob Aircraft AG, Lettenbachstrasse 9, D-86874 Tussenhausen-Mattsies 
1.7 Approval Note:  
 
The technical content of this document is approved under the authority of EASA Design 
Organization Approval No. EASA.21J.030.  
 
These information or instructions relate to change no. MÄM1078-161 which has been approved 
under the authority of EASA Design Organisation Approval No. EASA.21J.030.  
 
1.8 Accomplishment/ Instructions  
 
Part A   
 
1.8.1 Ensure that the aircraft is safe for parking I.A.W. G 115E AMM chapter 10-10 and G 115EG 
Job Guide in analogy. 
 
1.8.2 Inspect elevator trim tab operating arm for s igns of cracking, especially both upper and 
lower surfaces from the rear bolt mounting holes to the rear of the operating arm. 
 
1.8.3 Remove trim tab I.A.W. G 115E AMM chapter 55- 20 para. 3B and G 115EG Job Guide 
in analogy 
 
1.8.4 Remove trim tab arm (item 10  in Fig. 3 ) by removing nut, washer and bolt (item 20, 30, 
40  in Fig. 3 ) 
 
 
10 
20 
30 
40 
Left Elevator 
 
Fig. 3 
 
 
1.8.5 Perform dye penetrant check or more significa nt NDT on trim tab arm P/N 115E-3758 
 
1.8.6 If no crack  is found, clean trim tab bracket and proceed with 1.8.8

### Page 4

MSB1078-186/2 
Page  4 of 6 
28 March 2012 
Replaces Issue: 08. Mar 2012  
  
 
1078-186_2 MSB, Inspection of elevator  trim tab arm Rev.2  G 115E/EG 
 
Grob Aircraft AG, Lettenbachstrasse 9, D-86874 Tussenhausen-Mattsies 
1.8.7 If a crack is confirmed , the trim tab arm has to be replaced by a new item. 
Note: Any finding has to be reported to Grob with aircraft S/N and flight hours. 
 
1.8.8 Install trim tab arm P/N 115E-3758 using bolt , washer and new locking nut (item 20, 30, 
40  in Fig. 3 ). Apply correct torque value I.A.W. G 115E AMM chapter 20-10 and 
G 115EG Job Guide in analogy. 
Note: In place of installing the original trim tab arm according 1.8.8, you may proceed with 
1.8.14 of Part B following receipt of new material. 
 
1.8.9 Install trim tab I.A.W. G 115E AMM chapter 55 -20 para. 3C and G 115EG Job Guide in 
analogy 
Note: Make sure, that the bolt holes of trim rods 3 are i n alignment with the trim arm and the 
bolts may be installed easily. If necessary adjust accordingly I.A.W. G 115E AMM chapter 
27-31 para. B and G 115EG Job Guide in analogy. 
 
1.8.10 Return aircraft to service as per relevant p rocedures and regulations. 
 
Part B Terminating Action  
 
1.8.11 Ensure that the aircraft is safe for parking  I.A.W. G 115E AMM chapter 10-10 and 
G 115EG Job Guide in analogy. 
 
1.8.12 Remove trim tab I.A.W. G 115E AMM chapter 55 -20 para. 3B and G 115EG Job Guide 
in analogy 
 
1.8.13 Remove trim tab arm (item 10 in Fig. 3) by r emoving nut, washer and bolt (item 20, 30, 
40 in Fig. 3) 
 
1.8.14 Install new trim tab arm P/N 115E-3758/1  (item 4 of List 2.2) using bolt, washer and new 
locking nut (item 20, 30, 40 in Fig. 3). Apply correct torque value I.A.W. G 115E AMM 
chapter 20-10 and G 115EG Job Guide in analogy. 
 
1.8.15 Install trim tab I.A.W. G 115E AMM chapter 5 5-20 para. 3C and G 115EG Job Guide in 
analogy 
Note: Make sure, that the bolt holes of trim rods 3 are i n alignment with the trim arm and the 
bolts may be installed easily. If necessary adjust accordingly I.A.W. G 115E AMM chapter 
27-31 para. B and G 115EG Job Guide in analogy. 
 
1.8.16 Return aircraft to service as per relevant p rocedures and regulations.

### Page 5

MSB1078-186/2 
Page  5 of 6 
28 March 2012 
Replaces Issue: 08. Mar 2012  
  
 
1078-186_2 MSB, Inspection of elevator  trim tab arm Rev.2  G 115E/EG 
 
Grob Aircraft AG, Lettenbachstrasse 9, D-86874 Tussenhausen-Mattsies 
1.9 Repetitive Actions  
 
Repeat special inspection in para 1.8 Part A every 200FH until the terminating action Part B is 
accomplished.  
For regular inspection refer to G 115E AMM, Chap. 05-20, para. 10 and G 115EG Job Guide in 
analogy.  
 
II. PLANNING INFORMATION  
2.1 Weight and CG  
 
N/A 
 
2.2 Material and Availability  
 
Item P/N  Description Qty. / A/C 
1 115E-3758 Trim Tab Arm  (pre-modification)  1 
2 LN9348-05 Lock Nut 4 
3 LN9348-06 Lock Nut 1 
4 115E-3758/1 Trim Tab Arm (post modification) 1 
 
2.3 Special Tools  
 
N/A 
 
2.4 Labor costs  
 
N/A 
2.5 Reference documents  
 
Corresponding AMM and IPC 
 
2.6 Credit  
 
N/A

### Page 6

MSB1078-186/2 
Page  6 of 6 
28 March 2012 
Replaces Issue: 08. Mar 2012  
  
 
1078-186_2 MSB, Inspection of elevator  trim tab arm Rev.2  G 115E/EG 
 
Grob Aircraft AG, Lettenbachstrasse 9, D-86874 Tussenhausen-Mattsies 
III. REMARKS  
The instructions in paragraph 1.8 have to be accomplished and certified in the logbook by 
authorized staff: 
 
- in EASA countries  according to Article 5 VO EG 2042/03 (VO EG 1056/2008) Appendix III – 
Part 66 
 
- in non-EASA countries  according to national regulations with respect to maintenance. 
 
 
If you have sold your aircraft in the meantime, we kindly ask you to forward this information to 
the new owner and to provide us with the name and address of the new owner as well as with 
the respective serial number. 
 
For questions and assistance please contact: 
 
 Rudi Vodermeier,  Head of Customer Service & Suppo rt,   
phone:  +49 8268 998139 
 fax:            +49 8268 998200 
 e-mail:  productsupport@grob-aircraft.de  
 
 
SB-Index: http://www.grob-aircraft.eu/service-and-support/g-115.html  
Order:   http://www.grob-aircraft.eu/service-and-support/general/order-form.html

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
