# Guimbal Service Bulletin 25-006: No revision named

- Rights: © Guimbal. Filed by the FAA in regulations.gov docket FAA-2026-4630; AD 2026-19-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Guimbal Service Bulletin 25-006](https://openairdocs.org/service-documents/guimbal/sb-25-006.md)
- Title as filed: Guimbal Mandatory Service Bulletin SB 25-006 B
- Pages: 17
- PDF: https://openairdocs.org/files/sha256/cf/47/cf47bb638ded3da84f83a848d850e7446446178a0246b74f59f1cb5e3098c666
- Page: https://openairdocs.org/service-documents/guimbal/sb-25-006/file/cf47bb638ded

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  1 / 17 
 
 
Applicability 
Cabri G2 from S/N 1003 to S/N 1389 except 1383 and 1388. 
 
 
Situation 
HG has had reports of weak ELT signals when transmitting. 
 
Testing has showed that the root cause was the location of the ELT antenna. 
 
This Service Bulletin depicts the relocation of the ELT antenna and, if applicable, of the VHF2 
antenna as well. 
  
 
SERVICE BULLETIN 
SB 25-006 B  
 MANDATORY  RECOMMENDED 
 OPTIONAL  REPAIR 
Subject ELT Antenna Relocation 
Date of Entry into Force  December 12th; 2025 
Deadline 6 months from the effective date of the associated AD (June 19th, 2026) 
Associated Airworthiness Directive  EASA AD 2025-0282 
Associated Modification / Repair MOD 25-010 / 25-022 
Impact on Weight and Balance N/A 
HG Contact 
Customer Support 
 
Tel: +33 (0)4 42 39 10 88 E-Mail: support@guimbal.com 
Revision Subject Date 
A Creation Oct. 10th 2025 
B AD reference added, non-structural honeycomb engine cowl repair, minor improvements. Dec. 12th; 2025

### Page 2

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  2 / 17 
Cabri G2 
SERVICE BULLETIN 
Required Material 
Aircraft equipped with VHF2 
 
Reference Designation Qty Part Cons. Tool. 
G71-40-220 ELT Coaxial Cable 1 ●   
G72-03-220 VHF2 Antenna Bracket 1 ●   
G72-03-242 ELT Antenna Bracket 1 ●   
G72-23-110 VHF2 Antenna 1 ●   
HG12-0343 Nut 4 ●   
HG17-0551 Washer 4 ●   
HG22-0700 Pin 4 ●   
HG22-2692 Plug 1 ●   
HG45-1222 PE Tape 300 mm ●   
HG73-1153 Grommet 1 ●   
HG75-3696 ELT Antenna 1 ●   
HG21-2022 Tyrap 20  ●  
Local Procure. Carbide Router 1   ● 
Local Procure. Ø10 mm Drill Bit 1   ● 
Local Procure. Cyanoacrylate glue AR  ●  
 
  
KIT-SB25-006A

### Page 3

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  3 / 17 
Cabri G2 
SERVICE BULLETIN 
Aircraft not equipped with VHF2 
 
Reference Designation Qty Part Cons. Tool. 
G71-40-220 ELT Coaxial Cable 1 ●   
G72-03-242 ELT Antenna Bracket 1 ●   
HG12-0343 Nut 2 ●   
HG17-0551 Washer 2 ●   
HG22-0700 Pin 2 ●   
HG45-1222 PE Tape 300 mm ●   
HG73-1153 Grommet 1 ●   
HG75-3696 ELT Antenna 1 ●   
HG21-2022 Tyrap 20  ●  
HG40-2813 Fiberglass AR  ●  
HG40-0204 Peel ply AR  ●  
HG32-0188 Epoxy Resin AR  ●  
C3027 Cotton Flock AR  ●  
Local Procure. Methyl Ethyl Ketone AR  ●  
Local Procure. P80 Grit Abrasive AR   ● 
Local Procure. P160 Grit Abrasive AR   ● 
Local Procure. Carbide Router 1   ● 
Local Procure. Ø10 mm Drill Bit 1   ● 
 
Note: The references above shall be ordered under KIT-SB25-006A or -006B. 
 
 
Caution: Composite repair material for aircraft not equipped with VHF2 are not 
included in the associated kit . Check section 2 of the SB for applicability  and order 
separately, if required. 
  
KIT-SB25-006B

### Page 4

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  4 / 17 
Cabri G2 
SERVICE BULLETIN 
 
Required Actions 
1 Preliminary Steps 
IPC 7.2-02 
a) Remove the ELT from the luggage compartment, 
 
b) Switch the ELT OFF, 
 
c) Identify the ELT antenna [9] behind the cabin upholstery, pilot side, remove and discard 
the cable [18].

### Page 5

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  5 / 17 
Cabri G2 
SERVICE BULLETIN 
2 ELT Antenna Installation 
Aircraft equipped with VHF2 
 
IPC 7.3-00 
a) Remove the engine cowlings following MM 61-B-01, 
 
b) Disconnect the connector from the VHF2 antenna [13], 
 
c) Remove and discard VHF2 antenna [13], 
 
d) Open the tail boom firewall access door and remove both nuts from the upper LH tailboom 
fitting. Discard the existing VHF2 antenna bracket, 
 
e) Install the ELT antenna bracket G72-03-242 with washers HG17-0551, nuts HG12-0343, 
as shown below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
f) Torque nuts to 7.5 - 9 N.m and install cotter pins HG22-0700, 
 
g) Install the ELT antenna HG75-3696 on the bracket with its associated washer and nuts, as 
shown above, 
 
  
Washer 
HG17-0551 
Antenna Bracket 
G72-03-242 
Nut 
HG12-0343 
ELT Antenna 
HG75-3696

### Page 6

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  6 / 17 
Cabri G2 
SERVICE BULLETIN 
h) Use paper tape to mark the location of the ELT antenna as shown below, 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
i) Remove the ELT antenna and fold back the paper tape as shown below, 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
j) Install the engine cowlings following MM 61-B-02, 
 
k) Close the engine cowlings and fold the paper tape back in place as shown below,

### Page 7

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  7 / 17 
Cabri G2 
SERVICE BULLETIN 
l) Drill a Ø10 mm hole and enlarge to Ø22 mm using a carbide router, 
 
Note: Make sure there is at least a 2 mm gap between the antenna and the composite. 
 
m) If necessary, proceed to paint touch-up using paint listed in MM Supplement J70-013, 
 
n) Install the ELT antenna on the bracket with its associated washer and nuts, 
 
o) Remove both lower nuts and washers from the lower LH and RH tailboom fitting, discard 
nuts and washers, 
 
p) Install antenna bracket G72-03-220 with washers HG17-0551 and nuts HG12-0343 as 
shown below, 
 
q) Torque nuts to 7.5 - 9 N.m and install cotter pins HG22-0700, 
 
r) Close the tail boom firewall access door with associated screws, 
 
s) Install VHF2 antenna G72-23-110 with its associated washer on the antenna bracket, 
pointing downward as shown below, 
 
t) Connect VHF2 coaxial cable to the antenna as shown below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
Washer HG17-0551 
+ nut HG12-0343 
Antenna G72-23-110 
Antenna Bracket  
G72-03-220

### Page 8

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  8 / 17 
Cabri G2 
SERVICE BULLETIN 
u) Identify the interference area between VHF2 antenna and both lateral cowlings as shown 
below, 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
v) Using a carbide router, trim the cowlings, make sure there is at least a 5 mm gap 
between the antenna and the composite, 
 
w) If necessary, proceed to paint touch-up using paint listed in MM Supplement J70-013, 
 
x) Install a plug HG22-2692 in the former VHF2 antenna hole , bond it in place using 
cyanoacrylate glue. 
 
  
LH cowling 
RH cowling

### Page 9

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  9 / 17 
Cabri G2 
SERVICE BULLETIN 
Aircraft not equipped with VHF2 
IPC 6.6-00 
a) Open the tail boom firewall access door and remove both nuts from the upper LH tailboom 
fitting, 
 
b) Install the ELT antenna bracket G72-03-242 with washers HG17-0551, nuts HG12-0343, 
as shown below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
c) Torque nuts to 7.5 - 9 N.m and install cotter pins HG22-0700, 
 
d) Close the tail boom firewall access door with associated screws, 
 
e) Install the ELT antenna HG75-3696 on the bracket with its associated washers and nuts, 
as shown above, 
 
f) Use paper tape to mark the location of the ELT antenna, as shown below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
Washer 
HG17-0551 
Antenna Bracket 
G72-03-242 
Nut 
HG12-0343 
ELT Antenna 
HG75-3696

### Page 10

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  10 / 17 
Cabri G2 
SERVICE BULLETIN 
g) Remove the ELT antenna and fold back the paper tape as shown below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
h) Install the engine cowlings following MM 61-B-02, 
 
i) Close the engine cowlings fold the paper tape back in place as shown below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
j) Check whether the hole to be drilled interferes with existing honeycomb on the inner side. 
If it does, proceed to honeycomb repair as per section 4, prior to drilling, 
 
k) Drill a Ø10 mm hole and enlarge to Ø22 mm using a carbide router, 
 
Note: Make sure there is at least a 2 mm gap between the antenna and the composite. 
 
l) If necessary, proceed to paint touch-up using paint listed in MM Supplement J70-013, 
 
m) Install the ELT antenna on the bracket with its associated washer and nuts.

### Page 11

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  11 / 17 
Cabri G2 
SERVICE BULLETIN 
All aircraft 
3 ELT Antenna Cable Routing 
a) Inside the luggage compartment, identify the bottom forward plexiglass cap, 
 
b) Gain access to this cap by locally removing the upholstery, 
 
Note: This is a delicate task as the upholstery is quite fragile, use care. 
 
c) Drill a Ø10 mm hole inside the plexiglass cap identified above, enlarge to Ø22 mm using 
a carbide router, 
 
d) Install grommet HG73-1153 as shown below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
Looking inside the 
luggage compartment 
Grommet HG73-1153

### Page 12

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  12 / 17 
Cabri G2 
SERVICE BULLETIN 
e) Route the coaxial cable G71-40-220 along the luggage compartment, the engine frame up 
to the ELT antenna, as depicted below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Note: If AC is installed, remove the aft bulkhead prior proceeding to routing.

### Page 13

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  13 / 17 
Cabri G2 
SERVICE BULLETIN 
f) Install PE tape HG45-1222 on the engine frame and maintain ELT coax cable with tyraps 
HG21-2022, 
 
g) Connect the coax cable to the ELT antenna.

### Page 14

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  14 / 17 
Cabri G2 
SERVICE BULLETIN 
4 Engine Cowl Honeycomb Repair 
a) Mark the ELT antenna hole and the honeycomb to be trimmed as shown below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
b) Using a diamond cutting wheel or a carbide router, remove the honeycomb, the edges 
should then be sharp and free of chips as shown below, 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
c) Degrease the area using MEK and let it dry, do not wipe it with a cloth,

### Page 15

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  15 / 17 
Cabri G2 
SERVICE BULLETIN 
d) Mix the resin HG32-0188 with cotton flock C3027 until the desired texture is achieved, then 
apply a coat on the trimmed honeycomb as shown below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
e) Allow to cure at ambient temperature for 12 hours, 
 
f) If needed, flatten the surfaces using P80 grit abrasive, 
 
g) Prepare 3 plies of fiberglass HG40-2813 as shown below: 
• 2 plies Z1 and Z2 orientated at 0°/90°, 
• 1 ply Z3 orientated at ±45°, 
• 1 peel ply HG40-0204 covering the repaired area. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
Z3 
Z1 
Z2

### Page 16

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  16 / 17 
Cabri G2 
SERVICE BULLETIN 
h) Carefully laminate the air bubbles, 
 
i) Allow to cure at ambient temperature for 12 hours then 60°C for 4 to 6 hours, 
 
j) Sand the area using P160 grit abrasive, prior to finishing, 
 
k) Proceed to a paint touch -up on the affected zone  using paint listed in MM Supplement  
J70-013.

### Page 17

SB 25-006 B  The technical content of this document is approved under the authority of the DOA ref. EASA.21J.211  17 / 17 
Cabri G2 
SERVICE BULLETIN 
5 Flight Manual Temporary Revision 
a) If applicable, remove the Flight Manual Temporary Revision J40-001-TR1 from the flight 
manual. 
 
6 Final Steps 
a) Reinstall the ELT inside the luggage compartment, switch the ELT to ARMED, 
 
b) Turn Master and VHF2 ON, check radio transmission and reception, if applicable, 
 
c) Perform an ELT test following MM 72-C-02.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
