# Gulfstream Service Bulletin 150-24-193: No revision named

- Rights: © Gulfstream Aerospace Corporation. Filed by the FAA in regulations.gov docket FAA-2018-1006; AD 2019-03-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Gulfstream Service Bulletin 150-24-193](https://openairdocs.org/service-documents/gulfstream/sb-150-24-193.md)
- Title as filed: SB-150-24-193
- Pages: 8
- PDF: https://openairdocs.org/files/sha256/1f/21/1f2197e13a67a67cbc62ca88e82ba356c06fb1fbced1046cb01adeb41a61740b
- Page: https://openairdocs.org/service-documents/gulfstream/sb-150-24-193/file/1f2197e13a67

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SERVICE BULLETIN
SUBJECT
 
 
  
 
 
 
 
 
  
 
  
 
 
 
 
 
        
  
 
NUMBER  150-24-193 
 
 
 
 
ELECTRICAL POWER (ATA 24) – UPPER AND 
LOWER FRONT RELAY BOX REPLACEMENT 
 
 
 
 
 
 
 
MARCH 30, 2018

### Page 2

Gulfstream
SERVICE BULLETIN
Service Bulletin No. 150-24-193
Page 1 of 6
ELECTRICAL POWER - UPPER AND LOWER FRONT RELAY BOX REPLACEMENT
PLANNING INFORMATION
1. Effectivity
Aircraft serial numbers 201 through 326
2. Concurrent Requirement
None
3. Reason
Due to the possibility of corrosion in the relay box connector’s solder joint to the printed 
circuit board, acrylic conformal coating has been added to prevent this condition.
4. Description
This service bulletin provides instructions to remove and replace the upper front relay 
box IAI P/N 25G8130301-XXX with an improved upper front relay box
IAI P/N 25G8130301-516 upgraded to MOD A, and to remove and replace the lower 
front relay box IAI P/N 25G8130300-XXX with an improved lower front relay box
IAI P/N 25G8130300-520 upgraded to MOD A.
5. Compliance
Compliance with this service bulletin is mandatory at the next suitable planned 
maintenance period within 36 months from the original release date of this service 
bulletin.
6. Approval
This service bulletin has been reviewed by the Civil Aviation Authority of Israel (CAAI). 
The design content herein complies with the applicable Civil Aviation Regulations and 
is CAAI-approved.
7. Manpower
The following information is for planning purposes only:
Estimated labor-hours: 220
March 30, 2018

### Page 3

Gulfstream
SERVICE BULLETIN
Service Bulletin No. 150-24-193
Page 2 of 6
8. Weight and Balance
None
9. Electrical Load Data
No Change
10. Software Accomplishment Summary
None
11. References
G150 Aircraft Maintenance Manual (AMM), Chapters 20 and 24
G150 Illustrated Parts Catalog (IPC), Chapter 24
Gulfstream Aerospace LP G150 TC Design Change MOD G15-10087
Aircraft serial number specific Instructions for Continued Airworthiness (ICA) for Cabin 
Interior STC ST10316SC-D, Document GA32204AXXX, Chapter 25-34-00 Galley
G150 Completion Center Maintenance Handbook (CCMH), Chapter 25
This Service Bulletin incorporates design data approved under G150 TC design 
change MOD G15-10087 for installation on the standard type certificated aircraft. 
Approval for any deviation from the instructions contained in this service bulletin should 
be obtained, if required, from the local regulatory authority in accordance with the local 
relevant regulations.
NOTE: All references in th is document are intended to be inclusive of any 
amendments or revisions unless otherwise stated.
12. Other Publications Affected
G150 IPC, Chapter 24
13. Interchangeability or In termixability of Parts
N/A
March 30, 2018

### Page 4

Gulfstream
SERVICE BULLETIN
Service Bulletin No. 150-24-193
Page 3 of 6
MATERIAL INFORMATION
1. Material - Availability
NOTE: Due to material lead times, and the limited number of units being available at 
any one time, it is critical to confirm material availability by contacting 
Gulfstream Scheduling at 800-810-GULF (4853) or 912-965-4178.
If not scheduled, down times could increase significantly.
Removed components must be returned to Gulfstream Aerospace Material 
Services Repair Control Center within five (5) days of receiving replacement 
parts. Repair Control may be reached at 800-810-GULF (4853) or 
912-965-4178.
2. Warranty Information - Component
Labor and materials will be at no charge if the aircraft is still within the component warranty 
periods and this service bulletin is accomplished within the recommended compliance time, 
as stated in this document, at a Gulfstream G150 Authorized Warranty Facility or Factory 
Authorized Service Center. *
*Coverage is granted per the terms and conditions of the Gulfstream Aircraft Sales 
Agreement to the original purchaser or subsequent owner with appropriate Assignment of 
Warranties on file with Gulfstream.
NOTE: Additional labor hours incurred due to aircraft configuration or mechanical 
difficulties must be charged on a separate work order and submitted for 
warranty consideration.
3. Material Necessary for Each Aircraft
A. Material to be Procured:
* Upgraded to MOD A
New P/N Keyword Old P/N Qty
* IAI P/N 25G8130301-516 Upper Front 
Relay Box
IAI P/N 
25G8130301-510/-512/-
514/-516
1
* IAI P/N 25G8130300-520 Lower Front 
Relay Box
IAI P/N 
25G8130300-512/-516/-
518/-520
1
March 30, 2018

### Page 5

Gulfstream
SERVICE BULLETIN
Service Bulletin No. 150-24-193
Page 4 of 6
B. Materials Supplied by Operator:
None
4. Reidentified Parts
None
5. Special Tooling
Low resistance digital ohmmeter, GSE2401147 (247001) or equivalent
Torque wrench 0 - 15 inch pounds, GSE5101144 (151DIN) or equivalent
March 30, 2018

### Page 6

Gulfstream
SERVICE BULLETIN
Service Bulletin No. 150-24-193
Page 5 of 6
ACCOMPLISHMENT INSTRUCTIONS
CAUTION: PROTECT WIRE BUNDLE S, CONNECTORS AND SURROUNDING 
STRUCTURE DURING ANY MAINTENANCE PROCEDURES FROM 
SHAVINGS, DEBRIS AND CONTAMINATION. MAINTAIN A PROPERLY 
CLEANED WORK AREA THROUGHOUT THE PROCEDURE TO ENSURE THE 
INTEGRITY OF THE AFFECTED COMPONENT/SYSTEM. VISUALLY 
INSPECT WORK AREA USING ADDITIONAL LIGHT AS NECESSARY TO 
VERIFY ABSENCE OF ANY DEBRIS PRIOR TO COMPLETION OF 
PROCEDURE. FAILURE TO COMPLY MAY RESULT IN DAMAGE TO 
COMPONENTS AND/OR SYSTEMS.
1. Prepare aircraft for safe maintenance. Re fer to Aircraft Maintenance Manual (AMM), 
Chapter 20.
CAUTION: MAKE SURE ELECTRICAL POWER IS DISCONNECTED FROM AIRCRAFT. 
FAILURE TO COMPLY MAY RESULT IN INJURY TO PERSONNEL AND/OR 
DAMAGE TO AIRCRAFT.
2. Disconnect external electrical power from  aircraft. Refer to AMM, Chapter 20.
3. Remove interior to gain access to front relay box.
NOTE: Both the upper and lower front relay boxes are located on the right side of 
the aircraft directly above/below one another.
4. Inspect data plate to determ ine if MOD A unit is installed. If MOD A unit is installed, 
then no further action is required for the upper front relay box. Proceed to Step 6.
5. Remove and replace upper front relay box, IAI P/N 25G8130301-510/-512/-514/-516 
with IAI P/N 25G8130301-516 upgraded to MOD A in accordance with AMM, Chapter 
24-60-03. Perform the Follow On instructions only when arriving to Step 9 below.
NOTE: Ensure bonding strap is removed from airframe side and sent back with the 
removed unit.
6. Remove interior to gain a ccess to lower front relay box.
7. Inspect data plate to determ ine if MOD A unit is installed. If MOD A unit is installed, 
then no further action is required for the lower front relay box. Proceed to Step 9.
8. Remove and replace lowe r front relay box, IAI P/N 25G8130300-512/-516/-518/-520 
with IAI P/N 25G8130300-520 upgraded to MOD A in accordance with AMM, Chapter 
24-60-04. Perform the Follow On instructions only when arriving to Step 9 below.
NOTE: Ensure bonding strip is removed from airframe side and sent back with the 
removed unit.
March 30, 2018

### Page 7

Gulfstream 
SERVICE BULLETIN
Service Bulletin No. 150-24-193
Page 6 of 6
9. Perform the Follow On instru ctions for replacement of upper and/or lower front relay 
boxes in AMM, Chapter 24-60-03 and/or 24-60-04 in accordance with the box(es) 
which was/were actually replaced. If both boxes were replaced, then common actions 
which appear in both Follow On sections should be performed only once.
10. Tag any removed relay boxes, IAI P/ N 25G8130301-510/-512/-514/-516 and IAI P/N 
25G8130300-512/-516/-518/-520, and return to Gulfstream.
NOTE: Protective caps must be used on all connectors and relay boxes should be 
placed in an ESD bag. The unti shall be placed into the product specific 
wooded crate with product specific foam inserts. Otherwise, additional fees 
may be incurred. Contact Parts Sales if none are available. Crates and 
foam inserts used in shipping upgraded units shall be used for returned 
units.
11. Install interior removed in Steps 3 and 6.
12. Ensure work area is clean a nd clear of foreign objects (FOD).
13. Record compliance with this service bulleti n in the aircraft’s permanent maintenance 
records and return aircraft to flight status.
14. Report compliance with this service bu lleting to Gulfstream Computerized 
Maintenance Program (CMP) by uploading the attached service reply card, along with 
the CMP task card(s) sign-off using MyGulfstream, MyCMP Document Upload or 
e-mail to cmp.docproc@campsystems.com.
If technical assistance is required, contact your area Gulfstream Field Service 
Representative or call Gulfstream Customer Support at 800-810-GULF (4853).
March 30, 2018

### Page 8

GULFSTREAM G150 
SERVICE BULLETIN NO. 150-24-193 
SERVICE REPLY CARD 
Service Bulletin prepared by Gulfstream Aerospace, 500 Gulfstream Road, P.O. Box 2206, Savannah, Georgia 
31402-2206, USA. © 2018 Gulfstream Aerospace. All rights reserved, including the right to reproduce this publication.  
No part may be reproduced, stored in any retrieval system, or transmitted in any part or form or by any means, 
electronic, photocopying, microfilm, microfiche, mechanical, or otherwise, without prior written permission of 
Gulfstream Aerospace. This technical data is controlled under the Export Administration Regulations by General 
License TSU.  It may not be transferred to a third party without the prior written approval of the U.S. Department of 
Commerce. 
 
Please upload this page, along with the CMP task card(s) sign-off using MyGulfstream, 
MyCMP Document Upload, or e-mail to cmp.docproc@campsystems.com 
  
The following Service Bulletin (SB) has been addressed: 
SB CMP NUMBER A/C AIRCRAFT TYPE COMPLIANCE  DATE 
981930  Gulfstream G150  
 
Aircraft Hours _ _____________________ 
Aircraft Landings_____________________  
 
This Service  Bulletin is not applicable because: 
 
_______ Serial Number not affected 
_______ Equipment not installed 
_______Previously complied with (annotate method of compliance below) 
_______Other (explain reason below) 
 
 
   
SIGNATURE TITLE / CERTIFICATE    
NUMBER 
COMPANY 
 
   
COMMENTS / SUGGESTIONS / ACTIONS TAKEN:

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
