# Hamilton Sundstrand Alert Service Bulletin 54H60-61-A154

## Copies (2)

Copies the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.

- Revision 1 ("Hamilton Sundstrand ASB 54H60-61-A154  Rev 1"): PDF https://openairdocs.org/files/sha256/e6/c7/e6c7a1ab95e083f32b04bf99e120b0d159e04256da85d3efae542af819d85cf0; text https://openairdocs.org/service-documents/hamilton-sundstrand/54h60-61a154/file/e6c7a1ab95e0.md. Rights: © Hamilton Sundstrand Corporation. Filed by the FAA in regulations.gov docket FAA-2021-0032; AD 2022-08-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Hamilton Sundstrand SB_54h60_61_a154 ("Hamilton Sundstrand SB_54h60_61_a154"): PDF https://openairdocs.org/files/sha256/9c/50/9c500e09b02429ea1ea8925f7defe1b46a2adb85505e76529a7e3221f9429c8f; text https://openairdocs.org/service-documents/hamilton-sundstrand/54h60-61a154/file/9c500e09b024.md. Rights: © Hamilton Sundstrand Corporation. Filed by the FAA in regulations.gov docket FAA-2019-1008; AD 2020-12-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Hamilton Sundstrand](https://openairdocs.org/service-documents/hamilton-sundstrand.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: 54H60-61-A154
- Latest revision known: 54H60-61-A154, Revision 1, dated May 29, 2020 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/hamilton-sundstrand/54h60-61a154

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2022-08-10](https://openairdocs.org/ad/2022-08-10.md), effective May 27, 2022: Revision 1
- [AD 2020-12-07](https://openairdocs.org/ad/2020-12-07.md), effective Jul 20, 2020: No revision named

Also cited in [2 proposed ADs](https://openairdocs.org/service-documents/hamilton-sundstrand/54h60-61a154/proposed.md).

## Text (20 pages)

Revision 1, the newest copy. Rights: © Hamilton Sundstrand Corporation. Filed by the FAA in regulations.gov docket FAA-2021-0032; AD 2022-08-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

(No text on this page.)

### Page 2 (OCR)

UTC Aerospace Systems
Hamilton Sundstrand Corporation, a UTC Aerospace Systems Company
ALERT SERVICE BULLETIN
PLANNING INFORMATION
A. Effectivity
(1) Hamilton Sundstrand Variable Pitch Aircraft Propeller, Model 54H60, Part Number
(PN) 54H60 series, all serial numbers (SN)s that contain a blade below SN 813320.
NOTE:  If a propeller contains a blade below SN 813320, all of the blades on that
propeller are subject to this bulletin.
(2) Hamilton Sundstrand Variable Pitch Aircraft Propeller, Model 54H60, PN 54H60
series, all serial numbers, if the propeller contains blades that have not been
overhauled within ten years.
B. Concurrent Requirements
(1) Beginning August 1, 2020, this bulletin must be done at the same time as Alert Service
Bulletin (ASB) 54H60-61-A155.
C. Reason
(1) Problem
(a) Propeller blades below SN 813320 may be more susceptible to have intergranular
cracks in the taper bore (refer to Figure 1).
TYPICAL
CRACK
ASB-54H60-61-A154-135353
Figure 1
Typical Crack Orientation and Location in the Propeller Blade Taper Bore
U.S. Export Classification: EAR 9E991
COLLINS AEROSPACE PROPRIETARY - Subject to the restriction on the title or cover page.
Original Issue Date: Aug 26/19  54H60-61-A154
Revision 1: May 29/20  Page 2

### Page 3

(No text on this page.)

### Page 4

(No text on this page.)

### Page 5

(No text on this page.)

### Page 6

(No text on this page.)

### Page 7

(No text on this page.)

### Page 8

(No text on this page.)

### Page 9 (OCR)

• UTC Aerospace Systems
Hamilton Sundstrand Corporation, a UTC Aerospace Systems Company
ALERT SERVICE BULLETIN
INTERNAL
TAPER BORE
INSPECTION
AREA
ASB-54H60-61-A154-135352
Figure 2
Internal Taper Bore on the Propeller Blade
(2) Equipment Setup:
NOTE: This procedure is written for the Nortec 600 series eddy current tester.
Equivalent equipment must be set up to meet the same inspection sensitivity
and coverage.
WARNING: USE ISOPROPYL ALCOHOL, TT-1-735 OR ASTM D770, CORRECTLY.
ISOPROPYL ALCOHOL IS FLAMMABLE, EXPLOSIVE, AND A MILD
POISON. IT CAN HAVE A BAD EFFECT ON YOUR HEALTH OR
SAFETY. BEFORE YOU USE THE ISOPROPYL ALCOHOL, GET THE
MATERIAL SAFETY DATA SHEET FROM THE MANUFACTURER OR
SUPPLIER OF THE MATERIAL AND READ IT CAREFULLY. READ THE
DETAILED WARNING, WO046SE, IN THE WARNINGS REGISTRY SPM
20-00-04. BEFORE YOU USE THE ISOPROPYL ALCOHOL, PUT ON
CHEMICAL-SPLASH GOGGLES. MAKE SURE THAT YOU HAVE
SUFFICIENT AIRFLOW TO KEEP THE ISOPROPYL ALCOHOL FUMES
BELOW THE MATERIAL SAFETY DATA SHEET LIMIT.
(a) Clean the eddy current probe with a clean lint-free cleaning cloth made moist with
isopropyl alcohol, TT-I-735.
U.S. Export Classification: EAR 9E991
COLLINS AEROSPACE PROPRIETARY - Subject to the restriction on the title or cover page.
Original Issue Date: Aug 26/19  54H60-61-A154
Revision 1: May 29/20  Page 9

### Page 10 (OCR)

UTC Aerospace Systems
Hamilton Sundstrand Corporation, a UTC Aerospace Systems Company
ALERT SERVICE BULLETIN
(b) Use the 16-pin lemo cable to connect the eddy current probe to the eddy current
tester.
CAUTION: MAKE SURE TO APPLY TEFLON TAPE ON THE EDDY CURRENT
PROBE CORRECTLY. THE TAPE MUST EXTEND COMPLETELY
OVER THE PROBE TIP AND UP THE TWO SIDES OF THE PROBE
LEG. THIS WILL DECREASE THE RISK OF BLADE DAMAGE WHILE
YOU DO THE INSPECTION.
(c) Apply Teflon tape to the end of the eddy current probe as shown in Figure 3.
NOTE:  The Teflon tape may need to be replaced frequently. It is critical to make
sure that Teflon tape is applied correctly and used in all steps of this
procedure.
TEFLON TAPE
EXTENDS COMPLETELY
OVER THE PROBE  EDDY
TIP AND UP THE TWO  CURRENT
SIDES OF PROBE LEG  PROBE
SHAFT
ASB-54H60-61-A154-135355
Figure 3
Teflon Tape Application
(d) Turn the eddy current tester power on and let the tester run for at least 10 minutes
before the inspection.
NOTE: The screen trace or flying dot can drift up to two major divisions in 15
minutes or less when the eddy current tester is initially powered up.
(e) Set the eddy current tester (refer to Figure 4) to the default settings by either:
• Selecting LOAD DEFAULT and pressing the enter (checkmark) key when
prompted during start-up.
• Doing the steps that follow:
1 Press the ADV SETUP key.
2 Select the SETUP 1 MENU.
3 Select LOAD DEFAULT.
4 Press the enter (checkmark) key (refer to Figure 4) when prompted.
U.S. Export Classification: EAR 9E991
COLLINS AEROSPACE PROPRIETARY - Subject to the restriction on the title or cover page.
Original Issue Date: Aug 26/19  54H60-61-A154
Revision 1: May 29/20  Page 10

### Page 11 (OCR)

UTC Aerospace Systems
Hamilton Sundstrand Corporation, a UTC Aerospace Systems Company
ALERT SERVICE BULLETIN
OLYMPUS
Vp# 9.8
ENTER
(CHECKMARK)
KEY
DO 49.1
NORTED BO0
ASB-54H60-61-A154-135358
Figure 4
Eddy Current Tester
(f) Press the MAIN/FILTER key to go back to the home screen.
Adjust the eddy current tester settings (refer to Table 3). Minor adjustments to
these settings are permitted as necessary, to get optimum signal characteristics.
NOTE: Display erase or display persist, if used, must be set at no less than 2
seconds. Shorter intervals can make it difficult to measure amplitudes
of crack signals relative to the null or reference level and can cause
crack indications to be erased before the signal completes an up and
down motion.
Table 3
Initial Settings for Surface Scan of Aluminum
Parameter  Description/Setting
ADV SETUP MENU (SETUP & SPECIAL)
FRQ MODE (Column 1)  SINGLE
PRB DRV (Column 1)  MEDIUM
U.S. Export Classification: EAR 9E991
COLLINS AEROSPACE PROPRIETARY - Subject to the restriction on the title or cover page.
Original Issue Date: Aug 26/19  54H60-61-A154
Revision 1: May 29/20  Page 11

### Page 12

(No text on this page.)

### Page 13

(No text on this page.)

### Page 14 (OCR)

UTC Aerospace Systems
Hamilton Sundstrand Corporation, a UTC Aerospace Systems Company
ALERT SERVICE BULLETIN
(h) Examine the sensitivity of your inspection set-up by scanning over the 0.005,
0.010 and 0.020-inch deep reference notches.
• The three responses should appear similar to Figure 6.
• The response from the 0.005-inch notch should make a minimum 5% FSH
vertical response (one-half of one division) and should be clearly discernible
from the baseline noise.
1 If these responses are not obtained, examine the eddy current tester setup
and do the standardization procedure again. If, after re-standardization, this
sensitivity cannot be obtained, select a different eddy current probe and do
the standardization procedure again.
80% VERTICAL
SIGNAL TRACE
ASB-54H60-61-A154-135350
Figure 5
Signal Response from a 0.020-Inch Notch in Aluminum
U.S. Export Classification: EAR 9E991
COLLINS AEROSPACE PROPRIETARY - Subject to the restriction on the title or cover page.
Original Issue Date: Aug 26/19  54H60-61-A154
Revision 1: May 29/20  Page 14

### Page 15 (OCR)

• UTC Aerospace Systems
Hamilton Sundstrand Corporation, a UTC Aerospace Systems Company
ALERT SERVICE BULLETIN
- 0.020 INCH DEEP NOTCHI
0.010 INCH DEEP NOTCH
0.005 INCH DEEP NOTCH
ASB-54H60-61-A154-135351
Figure 6
Acceptable Sensitivity Check Signal (Aluminum)
(4) General Inspection Technique
(a) Do a scan as follows:
CAUTION: MAKE SURE THAT GOOD CONTACT IS MAINTAINED BETWEEN
THE PROBE TIP AND THE PART TO BE INSPECTED. IF GOOD
CONTACT IS NOT MAINTAINED, THE EDDY CURRENT TESTER
WILL GIVE INCORRECT INDICATIONS.
1 Place the eddy current probe on the part to be inspected. Make sure that
there is good contact between the probe tip and the part.
2 Make sure that the probe tip is located a minimum of twice the probe
diameter from the nearest edge.
3 Press the NULL key on the eddy current tester and hold the eddy current
probe still until nulling is complete.
NOTE:  Periodic nulling can be necessary during the inspection to keep the
baseline at 10% FSH and 80% full screen width (FSW).
U.S. Export Classification: EAR 9E991
COLLINS AEROSPACE PROPRIETARY - Subject to the restriction on the title or cover page.
Original Issue Date: Aug 26/19  54H60-61-A154
Revision 1: May 29/20  Page 15

### Page 16

(No text on this page.)

### Page 17 (OCR)

• UTC Aerospace Systems
Hamilton Sundstrand Corporation, a UTC Aerospace Systems Company
ALERT SERVICE BULLETIN
- SEE NOTE
PROBE SHAFT
CLIPS IN REAR
SUPPORT
PROBE TIP
PROTRUDES
THROUGH
HOLE
EDDY
CURRENT
PROBE
NOTE:
THE EDDY CURRENT PROBE IS REMOVED TO SHOW THE HOLE.  ASB-54H60-61-A154-135356
Figure 7
Eddy Current Probe in Taper Bore Scanning Fixture
(c) Place the eddy current probe (with the taper bore scanning fixture, DA000767)
into the taper bore, beyond the bushing, as follows (refer to Figure 8):
1 Put the probe tip in contact with the taper bore inner surface and pull the
probe to the butt end of the blade until the probe leg is resting against the
inside edge of the bushing as shown in Figure 8.
(d) Make sure that the probe tip is on the taper bore inner surface and the probe leg
touches the inside edge of the bushing as shown in Figure 8. Press NULL on the
eddy current tester.
NOTE:  If necessary, the null point can be moved vertically to 20% FSH and
50% FSW to help keep the lift-off response on the display while
scanning.
U.S. Export Classification: EAR 9E991
COLLINS AEROSPACE PROPRIETARY - Subject to the restriction on the title or cover page.
Original Issue Date: Aug 26/19  54H60-61-A154
Revision 1: May 29/20  Page 17

### Page 18 (OCR)

UTC Aerospace Systems
Hamilton Sundstrand Corporation, a UTC Aerospace Systems Company
ALERT SERVICE BULLETIN
TAPER  (SEE NOTE)
BORE
- BUSHING
EDDY
CURRENT
PROBE
TAPER BORE
SCANNING
FIXTURE
BUTT END
PROBE TIP ON
TAPER BORE
SURFACE
PROBE LEG RESTING
AGAINST INSIDE
EDGE OF BUSHING
NOTE:
APPLY LIGHT PRESSURE AT ARROWS WITH FINGERS WHILE SCANNING.  ASB-54H60-61-A154-135357
Figure 8
Cross Section of Taper Bore Inspection Area
(e) Make sure that the lift-off signal on the eddy current tester is horizontal. Move the
eddy current probe and re-null until horizontal lift-off is obtained.
NOTE:  If the lift-off signal is not horizontal, the probe tip is not making contact
with the taper bore inner surface.
(f) Using the inside edge of the bushing as a guide, circumferentially scan around the
inner diameter surface of the taper bore two times as follows:
The standardization must be verified at 10-minute intervals (minimum).
If the notch signal does not provide 70-90% deflection, the
standardization and inspection must be done again.
1 Apply light pressure with your fingers while scanning (refer to Figure 8).
2 Make sure that the probe tip stays normal to the inspection surface to
prevent excessive lift-off.
U.S. Export Classification: EAR 9E991
COLLINS AEROSPACE PROPRIETARY - Subject to the restriction on the title or cover page.
Original Issue Date: Aug 26/19  54H60-61-A154
Revision 1: May 29/20  Page 18

### Page 19

(No text on this page.)

### Page 20

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
