# Hamilton Sundstrand Service Bulletin ERPS06G-29-6

Copy: No revision named ("SB ERPS06G-29-6"), 18 pages: PDF https://openairdocs.org/files/sha256/09/1b/091b0fe0a58ed97ab02189404eaba8eb1f83828f2ad073e099490ffcf8f2be31; text https://openairdocs.org/service-documents/hamilton-sundstrand/erps06g-29-6/file/091b0fe0a58e.md. Rights: © Hamilton Sundstrand Corporation. Filed by the FAA in regulations.gov docket FAA-2011-0388; AD 2011-16-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Hamilton Sundstrand](https://openairdocs.org/service-documents/hamilton-sundstrand.md)
- Type: Service bulletin (Service Bulletin)
- Number: ERPS06G-29-6
- Page: https://openairdocs.org/service-documents/hamilton-sundstrand/erps06g-29-6

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2011-16-03](https://openairdocs.org/ad/2011-16-03.md), effective Sep 9, 2011: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/hamilton-sundstrand/erps06g-29-6/proposed.md).

## Text (18 pages)

Rights: © Hamilton Sundstrand Corporation. Filed by the FAA in regulations.gov docket FAA-2011-0388; AD 2011-16-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

Hamilton Sundstrand
A United Technologies Company
SERVICE BULLETIN
© 2009 Hamilton Sundstrand Corporation
PROPRIETARY
TOLD ALL SUCH INFORMATION IN CONDENCE AND ACRES RE SHALL USED ONLY FOR RECIPIENTS INTERNAL PURPOSES TO MAINTAIN RECIPENTS  RECIPIENT AGREES TO
SUCH INFORMATION IN
REPAIRS MODIFICATONS SPARE PARIS DESION OF CONFIGURANTON CHANCES OR TO OBTAN PAN OR AN OCHER GSOVEANENT OR REQUATORY APPROVAL  THIS DOCUMENT AND THE INFORMATION
AGREES NOT TO DISCLOSE  SUCH INFORMATION TO ANY THIRD PARTY, EXCEPT AS MAY OTHERWISE BE PROVIDED FOR IN AN APPLICABLE
AGREEMENT BETWEEN RECIPIENT AND HSC.  COPYING OR DISCLOSURE OF  THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN BY ANYONE WTHOUT
HSC'S PRIOR WRITTEN PERMISSION IS NOT AUTHORIZED AND MAY RESULT IN CRIMINAL AND/OR CIVIL LIABILITY.
THE ANY TO SYSTEMS AND OR PARIS MALACTURED BY OR FOR ANATO% SUNDS AND OR PROVED BY HAMILTON SUNOSTRAND DO NOT RELY V AM  WAY ON DATA IN THIS DOCUMENT TO MAINTAIN OR OTHERWISE SUPPORT SYSTEMS AND/OR PARTS THAT WERE NOT MANUFACTURED BY OR FOR HAMILTON
SUNDSTRAND OR APPROVED BY HAMILTON SUNDSTRAND WITHOUT EVIDENCE THAT THE FEDERAL AVIATION ADMINISTRATION OR OTHER HEGULATORY AGENCY
HAS DETERMINED THAT THE DATA IN THIS DOCUMENT IS VALID FOR SUCH USE
Information Subject to Export Control Laws
THE TECHNICAL DATA IN THIS DOCUMENT (OR FILE) IS CONTROLLED FOR EXPORT UNDER THE EXPORT ADMINISTRATION REGULATIONS (EAR), 15 CFR PARTS 730.
774, ECCN: 9E991. VIOLATIONS OF THESE LAWS MAY BE SUBJECT TO FINES AND PENALTIES UNDER THE EXPORT ADMINISTRATION ACT.
Emergency Hydraulic Power - RAT Turbine-Lower Gearbox Assembly - Replace Balance Washer Screws
1.  Planning Information
A. Effectivity
The Hamilton Sundstrand Ram Air Turbine (RAT) Turbine-Lower Gearbox Assemblies, Model
ERPS06G, that are listed below and used on the Airbus A330 and A340 aircraft are affected by this
service bulletin:
Part Number
Series  Serial Numbers
766542  0028, 0101, 0102, 0103, 0153, 0212, 0219, 0253, 0426, 0442, 0506, 0541, 0551, 0630,
0647, 0740, 0744, 0763, 0765, 0819, 0854, 0864, 0885, 0912, 0913, 0914, 0915, 0916,
0917, 0918, 0919, 0920, 0921, 0922, 0923, 0924, 0926, 0927, 0928, 0929, 0930, 0931,
0932, 0933, 0934, 0935, 0936, 0937, 0938, 0939, 0940, 0941, 0942, 0943, 0944, 0945,
0946, 0947, 0948, 0949, 0950, 0951, 0952, 0953, 0954, 0955, 0956, 0957, 0958, 0959,
0960, 0961, 0962, 0964, 0965, 0967, 0969, 0970, 0971, 0972, 0973, 0974, 0975, 0977,
0978, 0979, 0980, 0981, 0982, 0984, 0985, 0986, 0987, 0988, 0989, 0991, 0992, 0993,
0994, 0995, 0996, 0997, 0998, 0999,  1000, 1001, 1002, 1003, 1005, 1006, 1007, 1009,
1015, 1018, 1019, 1020, 1024, 1025, 1026, 1031, 1034, 1035
1701401  0010, 0016, 0107, 0139, 0172, 0174, 0194, 0205, 0244, 0245, 0267, 0268, 0272, 0278,
0300, 0311, 0317, 0324, 0332, 0344, 0346, 0354, 0356, 0362, 0386, 0400
For information only: Records indicate the following Hamilton Sundstrand Ram Air Turbine (RAT)
Modules, Model ERPS06M, were delivered with affected RAT turbine-lower gearbox assemblies
from the list above:
NOTE: Not all turbine-lower gearbox assembly serial numbers can be allocated to a RAT module
serial number. Therefore, the following list of RAT modules is not exhaustive.
NOTE: The following list of RAT modules is given for information only, because the subject turbine-
lower gearbox assemblies may have been installed on another RAT module by the opera-
tor.
Jul 20/09  ERPS06G-29-6
Page 1 of 18

### Page 2 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
Part Number
Series  Serial Numbers
766351  0164
768084  0010, 0017, 102, 0167, 0172, 0219, 0233, 0242, 0256, 0257, 0259, 0265, 0268, 0277,
0297, 0303, 0317, 0330, 0348, 0350
770379  0156, 0410, 0426, 0490
770952  0525, 0535
1702934  0613, 0719, 0723, 0742, 0744, 0797, 0832, 0842, 0863, 0892, 0893, 0894, 0895, 0896,
0897, 0898, 0899, 0900, 0901, 0903, 0904, 0905, 0906, 0907, 0908, 0909, 0910, 0911,
0912, 0913, 0914, 0915, 0916, 0917, 0918, 0919, 0920, 0921, 0922, 0923, 0924, 0925
0926, 0927, 0928, 0929, 0930, 0931, 0932, 0933, 0934, 0935, 0936, 0937, 0938, 0939,
0941, 0942, 0944, 0946, 0947, 0948, 0949, 0950, 0951, 0952, 0954, 0955, 0956, 0957,
0958, 0959, 0961, 0962, 0963, 0964, 0965, 0966, 0968, 0969, 0970, 0971, 0972, 0973,
0974, 0975, 0976, 0977, 0978, 0979, 0981, 0982, 0983, 0985, 0994, 0999, 1000, 1001,
B. Concurrent Requirements
None.
C. Reason
Hamilton Sundstrand has discovered that RATs were manufactured with nonconforming screws. To
date, there have been five instances of a fractured balance washer screw on multiple RAT/turbine-
lower gearbox assembly part number configurations. Fracture of a balance washer screw can result
in the loss of the associated balance washer and create an unacceptable turbine imbalance. Inspec-
tion of other screws in Hamilton Sundstrand stock revealed metallographic nonconformities consis-
tent with those of the fractured screws. The suspect screws have been isolated to a lot from a
specific supplier. Analysis indicates the nonconformance could be a result of the supplier's heat treat
process, which increases susceptibility to brittle fracture. Replacement of the suspect screws with
confirmed conforming screws will eliminate potential loss of a balance washer. Incorporation of this
bulletin will ensure that the turbine-lower gearbox assembly balance washer screws conform to
specification.
D. Description
This bulletin gives instructions to replace the balance washer screws and identify the turbine-lower
gearbox assembly.
For a turbine-lower gearbox assembly with a missing balance washer, or with a balance washer
screw that cannot be removed in its entirety, instructions are also given to disassemble the turbine-
lower gearbox assembly as necessary to remove the fractured screw and balance washer, balance
the turbine assembly, assemble the turbine-lower gearbox assembly, and test the turbine-lower gear-
box assembly.
Jul 20/09  ERPS06G-29-6
Page 2
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 3 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
E. Compliance
Incorporation of this service bulletin is to be accomplished at the earliest opportunity.
F. Approval
This service bulletin contains no modification information that revises the approved configuration and
therefore does not require Federal Aviation Administration (FAA) or other regulatory agency
approval.
G. Manpower
A maximum of 0.5 man-hour will be required to replace the balance washer screws and identify the
turbine-lower gearbox assembly.
For a turbine-lower gearbox assembly with a missing balance washer, or with a balance washer
screw that cannot be removed in its entirety, a maximum of 9.0 man-hours will be required to disas-
semble the turbine-lower gearbox assembly as necessary to remove the fractured screw and bal-
ance washer, balance the turbine assembly, assemble the turbine-lower gearbox assembly, and test
the turbine-lower gearbox assembly.
H. Material - Cost and Availability
(1) Hamilton Sundstrand will supply replacement parts on a no-charge basis until July 19, 2011.
Replacement parts are currently available in limited quantities. Operators approved by Hamilton
Sundstrand to perform modification of units at their facility should place a single "no charge"
order to Hamilton Sundstrand. Operators can forward these orders to their assigned Hamilton
Sundstrand Commercial Spares Administrator (or fax to +1-815-226-2624, if the responsible
Administrator is not known). In addition, operators can also use the Hamilton Sundstrand web-
site at www.hamiltonsundstrand.com to contact the Commercial Spares group. Upon entering
the website, select "Customer Service" followed by "Commercial Spares" for other contact and
order processing options that are available.
(a) The two methods for establishing order quantities based on available fleet records are
listed below. In each case, Hamilton Sundstrand will acknowledge the operator order with
an established delivery rate.
1  For operators who can establish a listing of affected units in their fleet through the
review of records, Hamilton Sundstrand requests that a single purchase order be sub-
mitted for the total parts requirement. To minimize processing delays, orders must
clearly reference the service bulletin number, serial numbers of affected units, total
quantity of parts, and anticipated incorporation schedule. [To calculate the total quan-
tity of parts to order, refer to paragraph 3. (Material Information) for the parts break-
down on a per unit basis.]
If, at some point in the future, an operator finds that additional quantities of parts are
required, they should contact Hamilton Sundstrand with the details so that arrange-
ments can be made to provide them with the additional quantities.
Jul 20/09  ERPS06G-29-6
Page 3
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 4 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
For operators who cannot establish the total fleet requirements through the review of
records, Hamilton Sundstrand requests that an initial purchase order be submitted to
support 25 percent of their operating fleet or two aircraft, whichever is greater. This
will allow an operator to have parts available on shelf in the event that an affected unit
is found while performing inspections in accordance with this service bulletin. To mini-
mize processing delays, orders must clearly reference the service bulletin number
and quantity of parts. [To calculate the total quantity of parts to order, refer to para-
graph 3. (Material Information) for the parts breakdown on a per unit basis.]
If the initial quantity of parts provided is used and aircraft remain to be inspected,
operators should contact Hamilton Sundstrand with the details so that arrangements
can be made to provide additional parts.
(2) Hamilton Sundstrand will also give the following:
(a) A maximum labor allowance of 0.5 man-hour multiplied by the operator's current approved
hourly rate for accomplishment of this service bulletin in the shop. The labor allowance will
expire July 19, 2011.
(b) A maximum labor allowance of 0.5 man-hour multiplied by the operator's current approved
hourly rate for replacement of the balance weight/washer screws on the aircraft. The labor
(c) If removal from the aircraft is required, a maximum labor allowance of 6.0 man-hours multi-
plied by the operator's current approved hourly rate for replacement of the RAT on the air-
craft and test on wing. The labor allowance will expire July 19, 2011.
(d) Operators should forward a claim for labor reimbursement to their assigned Hamilton
Sundstrand Rockford Warranty Administrator. If the responsible Administrator is not
known, the claim should be mailed to Warranty Administration, 4747 Harrison Ave, Rock-
ford, IL 61126, USA, MS 106-6. The claim should reference the service bulletin number,
* serial numbers modified, date modified, total hours, and approved labor rate.
(3) For units with a missing balance weight/washer, or with a balance weight/washer screw that
cannot be removed in its entirety, Hamilton Sundstrand will incorporate this modification into
returned units at no charge until July 19, 2011. Contact Hamilton Sundstrand at the address
that follows for scheduling information:
Hamilton Sundstrand
4747 Harrison Avenue
P.O. Box 7002
Rockford, IL 61125-7002
Attention: Repair Administration
Mail Stop 151-6
Telephone: +1-815-226-6849
Fax: 815-394-2414
Tooling - Price and Availability
No tooling other than that required for shop maintenance of the turbine-lower gearbox assembly is
required to do this modification.
Jul 20/09  ERPS06G-29-6
Page 4
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 5 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
J. Weight and Balance
None.
K. Electrical Load Data
Not changed.
L. References
Applicable Aircraft Maintenance Manual (AMM), Hamilton Sundstrand Component Maintenance
Manual (CMM) 29-21-45, and Hamilton Sundstrand Standard Practices Manual (SPM) 20-00-00.
M. Other Publications Affected
Hamilton Sundstrand CMM 29-21-45 will be revised to incorporate this service bulletin.
2.  Accomplishment Instructions
A. General
CAUTION:  THE TURBINE-LOWER GEARBOX ASSEMBLY CONTAINS DESIGN CRITICAL
CHARACTERISTICS, PROCESSES, AND PROCEDURES. THE DESIGN CRITICAL
CHARACTERISTICS ARE IDENTIFIED WITH THE SYMBOL >>DCC<<. REFER TO
THE INTRODUCTION SECTION OF CMM 29-21-45 FOR A COMPLETE EXPLANA-
TION OF DESIGN CRITICAL CHARACTERISTICS.
(1)  The user should obtain the material safety data sheets [Occupational Safety and Health Act
(OSHA) Form 20 or equivalent] from the manufacturers or suppliers of materials to be used.
The user must become completely familiar with the manufacturer/supplier information and
adhere to the procedures, recommendations, warnings, and cautions of the manufacturer/sup-
plier for the safe use, handling, storage, and disposal of these materials. The user should also
read the long version of the warnings contained in this service bulletin. The long version warn-
ings are contained in Hamilton Sundstrand Warnings Registry 341-006 available free of charge
to all organizations that are on distribution for this Service Bulletin. The Warnings Registry
341-006 is also available at www.hsvas.com.
Jul 20/09  ERPS06G-29-6
Page 5
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 6 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
B. Modification - On the Aircraft
(1) Make sure the RAT is deployed (refer to the applicable AMM).
CAUTION:  THE TURBINE-LOWER GEARBOX ASSEMBLY TURBINE BLADE SHOULD BE PRO-
TECTIVELY COVERED DURING BALANCE WASHER SCREW REMOVAL AND
INSTALLATION. THE BLADES CAN BE EASILY DAMAGED.
(2)  Install a protective covering on the turbine-lower gearbox assembly turbine blades to prevent
damage to the blades from contact with the tooling or screws.
(3) Rotate the turbine assembly and do a check for missing balance washers (refer to Figure 1 of
this bulletin for the location of the balance washers).
NOTE:  The number of balance washers installed will vary according to the magnitude of the
imbalance that existed before the turbine assembly was balanced.
- The threaded holes around the turbine circumference (in the rear balance plane)
that are not used for balance washers have a set screw installed. The set screw
is secured using a 5/64-inch hex tool. The set screws should not be removed or
replaced.
- The threaded holes around the turbine circumference (in the rear balance plane)
with balance washers installed, use a countersunk socket head cap screw
MS24667-14 to secure the washers.
- The threaded holes around the turbine circumference (in the front balance
plane) each have a balance washer installed and use a countersunk socket
head cap screw MS24667-14 to secure the washers.
NOTE:  Missing balance washers are evidenced by the remaining screw shank and the lack of
a visible hexagonal screw socket on the turbine assembly.
(4) If any balance washers are missing (because of a fractured screw), the turbine-lower gearbox
assembly or RAT must be removed from the aircraft (refer to applicable AMM) for removal of the
fractured screw and to balance the turbine assembly. The unit must either be returned to Hamil-
ton Sundstrand or to a repair facility that has the capability to disassemble, repair, balance, and
test the turbine-lower gearbox assembly.
CAUTION:  REPLACE THE BALANCE WASHER SCREWS ONE AT A TIME. DO NOT REMOVE
ALL OF THE SCREWS AT THE SAME TIME. IF MORE THAN ONE SCREW IS
REMOVED AT A TIME, THE TURBINE ASSEMBLY MUST BE RE-BALANCED.
(5) If no balance washers are missing, do the steps that follow to replace the balance washer
screws (one at a time):
(a) For each balance washer that is unsymmetrical in shape, use a suitable temporary mark-
ing method (tape, indelible ink, or equivalent) to mark the radial orientation of the installed
balance washer. The original installed radial orientation of the washer must be maintained.
NOTE:  If a balance washer is circular in shape, it is not necessary to mark its radial orien-
tation.
Jul 20/09  ERPS06G-29-6
Page 6
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 7 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
(b) Rotate the turbine assembly until the balance washer is positioned in a manner to minimize
the potential for the balance washer to fall out (when the associated screw is removed).
CAUTION: DO NOT USE A WORN HEX TOOL WITH ROUNDED CORNERS TO REMOVE
THE SCREW. IF A WORN TOOL IS USED, THE POTENTIAL EXISTS FOR
STRIPPING THE SOCKET HEAD OF THE SCREW.
CAUTION: USE CARE NOT TO DAMAGE EITHER THE BALANCE WASHER OR TURBINE
ASSEMBLY IF IT IS NECESSARY TO STRIKE THE HEAD OF THE SCREW
BECAUSE THE BREAK-AWAY TORQUE IS EXCESSIVE.
(c) While holding the balance washer in place, use a 3/32-inch hex tool to remove one screw
from one balance washer.
NOTE: The use of a hex insert bit is preferred.
NOTE:  If the screw break-away torque is excessive, it is permissible to lightly strike the
head of the screw using a small hammer and a 5/16-inch (8-millimeter) pin punch.
It should not be necessary to strike more than two times.
(d) If the screw is fractured (with the balance washer installed) or if a screw fractures during
removal, do the steps that follow to remove the remaining portion of the screw:
1  Report any occurrences of a fractured screw to Hamilton Sundstrand as follows:
Greg Kuczek
Hamilton Sundstrand Service Engineering
Phone: +1- 815-226-6581
Fax: +1-860-660-4995
E-Mail: gregory.kuczek@hs.utc.com
If the remaining portion of the fractured screw is protruding above the turbine surface,
do the steps that follow:
Apply protective tape on the turbine (in the area of the screw) to prevent surface
damage during the removal attempt.
b Use pliers, a vice grip, or an equivalent gripping tool to remove the screw.
© Remove the protective tape from the turbine.
d If the screw is removed in its entirety, proceed to step 2.B.(5)(e) of this bulletin.
Jul 20/09  ERPS06G-29-6
Page 7
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 8 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
If the remaining portion of the screw is flush or below the turbine surface, or if the
screw can not be removed in its entirety, do the steps that follow:
Hamilton Sundstrand recommends the turbine-lower gearbox assembly or
RAT be removed from the aircraft (refer to the applicable AMM) for removal
of the fractured screw. The unit should either be returned to Hamilton Sund-
strand or to a repair facility that has the capability to disassemble, repair, bal-
ance, and test the turbine-lower gearbox assembly.
However, as an option, and at the operator's discretion, an attempt to
mechanically extract a screw while the turbine-lower gearbox assembly is
installed on the aircraft is allowed.
The procedure to mechanically extract a fractured screw, or one with a
stripped socket head, must not use any heat or fluid. Care must be taken to
make sure no filings or fragments enter the turbine assembly.
The turbine hub and turbine blades should be protectively covered to prevent
mechanically induced damage during the extraction procedure.
The self-locking screw thread insert should be visually inspected (after the
screw is extracted) to make sure there is no mechanical damage.
Some screws, depending on how near they are to a turbine blade, can not be
extracted unless the turbine blades are disassembled from the turbine
assembly. In those cases, the turbine-lower gearbox assembly or RAT must
be removed from the aircraft and disassembled as necessary to remove the
screw.
a  Use a screw extractor (or equivalent) to remove the remaining portion of the frac-
tured screw. Make sure no filings or fragments enter the turbine assembly. Do not
use heat or fluid to remove the screw.
NOTE: If the screw can not be extracted, the turbine-lower gearbox assembly
or RAT must be removed from the aircraft (refer to applicable AMM) and
disassembled as necessary to remove the screw. The unit should either
be returned to Hamilton Sundstrand or to a repair facility that has the
capability to disassemble, repair, balance, and test the turbine-lower
gearbox assembly.
b  Do a visual check of the self-locking screw thread insert to make sure there is no
mechanical damage.
(e) If the balance washer inadvertently falls off after the screw is removed, install the balance
washer in its original installed orientation, as determined from the marking method used in
• step 2.B.(5)(a) of this bulletin.
(T)  While holding the balance washer in place, install a new screw MS24667-14. Torque the
screw 18 to 22 pound inches (2.1 to 2.4 Newton meters).
(g)  Use a suitable temporary marking method (tape, indelible ink, or equivalent) to mark the
location where the balance washer screw has been replaced.
Jul 20/09  ERPS06G-29-6
Page 8
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 9 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
(h) Repeat steps 2.B.(5)(b) through (g) of this bulletin for each balance washer screw.
(i) Remove any tape (that was used to mark the orientation of the installed balance washers
or the locations where the screws had been replaced).
1) Remove the protective covering from the turbine-lower gearbox assembly turbine blades.
(6) After all of the balance washer screws have been replaced, identify the turbine-lower gearbox
assembly as follows:
(a)  Engrave or vibro-etch the symbol 29-6 on a blank area of the turbine-lower gearbox identi-
fication plate (refer to Figure 1 of this bulletin for the location of the turbine-lower gearbox
identification plate).
(7) Make sure the RAT is re-stowed (refer to the applicable AMM).
(8) Proceed to paragraph 2.F. of this bulletin.
Jul 20/09  ERPS06G-29-6
Page 9
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 10 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
C. Modification - In the Shop
CAUTION:  THE TURBINE-LOWER GEARBOX ASSEMBLY TURBINE BLADES SHOULD BE
PROTECTIVELY COVERED DURING BALANCE WASHER SCREW REMOVAL AND
INSTALLATION. THE BLADES CAN BE EASILY DAMAGED.
(1) Install a protective covering on the turbine-lower gearbox assembly turbine blades to prevent
damage to the blades from contact with the tooling or screws.
(2) Rotate the turbine assembly and do a check for missing balance washers (refer to Figure 1 of
this bulletin for the location of the following balance washers):
- Balance washers (10, IPL Figure 2, CMM 29-21-45), (20 through -20C), and
(30 through -30E).
NOTE: The number of balance washers installed will vary according to the magnitude of the
imbalance that existed before the turbine assembly was balanced.
- The threaded holes around the turbine circumference (in the rear balance plane)
that are not used for balance washers have a set screw installed. The set screw
is secured using a 5/64-inch hex tool. The set screws should not be removed or
replaced.
- The threaded holes around the turbine circumference (in the rear balance plane)
with balance washers installed, use a countersunk socket head cap screw
MS24667-14 to secure the washers [refer to screw (40, IPL Figure 2,
CMM 29-21-45)].
- The threaded holes around the turbine circumference (in the front balance
plane) each have a balance washer installed and use a countersunk socket
head cap screw MS24667-14 to secure the washers [refer to screw
(40, IPL Figure 2, CMM 29-21-45)].
NOTE:  Missing balance washers are evidenced by the remaining screw shank and the lack of
a visible hexagonal screw socket on the turbine assembly.
(3) If any balance washers are missing (because of a fractured screw), do the steps that follow:
(a) Report any occurrences of a fractured screw to Hamilton Sundstrand as follows:
Greg Kuczek
Hamilton Sundstrand Service Engineering
Phone: +1 - 815-226-6581
Fax: +1-860-660-4995
E-Mail: gregory.kuczek@hs.utc.com
Jul 20/09  ERPS06G-29-6
Page 10
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 11 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
(b) Disassemble the turbine-lower gearbox assembly (refer to CMM 29-21-45, DISASSEM-
BLY) as necessary to remove the following parts and to get access to the fractured screw.
- Balance washers (10, IPL Figure 2, CMM 29-21-45), (20 through -20C), and
(30 through -30E)
- Screws (40, IPL Figure 2, CMM 29-21-45)
NOTE:  Some screws, depending on how near they are to a turbine blade, can not be
extracted unless the turbine blades are disassembled from the turbine assembly.
in those cases, the unit must be disassembled as necessary to remove the screw.
(c)  Use a screw extractor (or equivalent) to remove the remaining portion of the fractured
screw. Make sure no filings or fragments enter the turbine assembly. Do not use heat or
fluid to remove the screw.
(d) Do a visual check of the self-locking screw thread insert to make sure there is no mechani-
cal damage.
(e) Assemble the turbine assembly as necessary (refer to CMM 29-21-45, ASSEMBLY).
(f) Remove the protective covering from the turbine-lower gearbox assembly turbine blades.
(g) Balance the turbine assembly (refer to CMM 29-21-45, ASSEMBLY).
(h) Assemble the turbine-lower gearbox assembly as necessary (refer to CMM 29-21-45,
ASSEMBLY).
(i) Do a test of the turbine-lower gearbox assembly (refer to CMM 29-21-45, TESTING AND
FAULT ISOLATION).
() After all of the balance washer screws have been replaced, identify the turbine-lower gear-
box assembly as follows (refer to SPM 20-00-00, ASSEMBLY):
1  Add the symbol 29-6 to a blank area of the identification plate (120 or -120A, IPL Fig-
ure 1, CMM 29-21-45) or (120, IPL Figure 1A).
(k) Proceed to paragraph 2.F. of this bulletin.
CAUTION: REPLACE THE BALANCE WASHER SCREWS ONE AT A TIME. DO NOT REMOVE
ALL OF THE SCREWS AT THE SAME TIME. IF MORE THAN ONE SCREW IS
REMOVED AT A TIME, THE TURBINE ASSEMBLY MUST BE RE-BALANCED.
(4) If no balance washers are missing, do the steps that follow to replace the balance washer
screws (one at a time):
(a) For each balance washer that is unsymmetrical in shape, use a suitable temporary mark-
ing method (tape, indelible ink, or equivalent) to mark the radial orientation of the installed
balance washer. The original installed radial orientation of the washer must be maintained.
NOTE  If a balance washer is circular in shape, it is not necessary to mark its radial orien-
tation.
(b) Position the unit to access the balance washer facing up.
Jul 20/09  ERPS06G-29-6
Page 11
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 12 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
CAUTION:  DO NOT USE A WORN HEX TOOL WITH ROUNDED CORNERS TO REMOVE
THE SCREW. IF A WORN TOOL IS USED, THE POTENTIAL EXISTS FOR
STRIPPING THE SOCKET HEAD OF THE SCREW.
CAUTION:  USE CARE NOT TO DAMAGE EITHER THE BALANCE WASHER OR TURBINE
ASSEMBLY IF IT IS NECESSARY TO STRIKE THE HEAD OF THE SCREW
BECAUSE THE BREAK-AWAY TORQUE IS EXCESSIVE.
(c)  While holding the balance washer in place, use a 3/32-inch hex tool to remove one screw
from one balance washer.
NOTE: The use of a hex insert bit is preferred.
NOTE: If the screw break-away torque is excessive, it is permissible to lightly strike the
head of the screw using a small hammer and a 5/16-inch (8-millimeter) pin punch.
It should not be necessary to strike more than two times.
(d) If the screw is fractured (with the balance washer installed) or if a screw fractures during
removal, do the steps that follow to remove the remaining portion of the screw:
1  Report any occurrences of a fractured screw to Hamilton Sundstrand as follows:
Greg Kuczek
Hamilton Sundstrand Service Engineering
Phone: +1- 815-226-6581
Fax: +1-860-660-4995
E-Mail: gregory.kuczek@hs.utc.com
2  If the remaining portion of the fractured screw is protruding above the turbine surface,
do the steps that follow:
a Apply protective tape on the turbine (in the area of the screw) to prevent surface
damage during the removal attempt.
Use pliers, a vice grip, or an equivalent gripping tool to remove the screw.
Remove the protective tape from the turbine.
d If the screw is removed in its entirety, proceed to step 2.C.(4)(e) of this bulletin.
If the remaining portion of the screw is flush or below the turbine surface, or if the
screw can not be removed in its entirety, do the steps that follow:
NOTE:  The procedure to mechanically extract a fractured screw, or one with a
stripped socket head, must not use any heat or fluid. Care must be taken to
make sure no filings or fragments enter the turbine assembly.
The turbine hub and turbine blades should be protectively covered to prevent
mechanically induced damage during the extraction procedure.
The self-locking screw thread insert should be visually inspected (after the
screw is extracted) to make sure there is no mechanical damage.
Jul 20/09  ERPS06G-29-6
Page 12
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 13 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
Disassemble the turbine-lower gearbox assembly (refer to CMM 29-21-45, DIS-
ASSEMBLY) as necessary to remove the following balance washers and to get
access to the fractured screw (40, IPL Figure 2, CMM 29-21-45);
- Balance washers (10, IPL Figure 2, CMM 29-21-45), (20 through -20C),
and (30 through -30E)
NOTE: Some screws, depending on how near they are to a turbine blade, can
not be extracted unless the turbine blades are disassembled from the
turbine assembly. In those cases, the unit must be disassembled as
necessary to remove the screw.
b  Use a screw extractor (or equivalent) to remove the remaining portion of the frac-
tured screw. Make sure no filings or fragments enter the turbine assembly. Do not
use heat or fluid to remove the screw.
Do a visual check of the self-locking screw thread insert to make sure there is no
mechanical damage.
If disassembly of the turbine assembly was not required to remove the fractured
screw, proceed to step 2.C.(4)(e) of this bulletin.
If disassembly of the turbine assembly was required to remove the fractured screw, do
the following:
a  Remove the remaining screws (40, IPL Figure 2, CMM 29-21-45) and the follow-
ing balance washers:
- Balance washers (10), (20 through -20C), and (30 through -30E)
Assemble the turbine assembly as necessary (refer to CMM 29-21-45, ASSEM-
BLY).
Remove the protective covering from the turbine-lower gearbox assembly turbine
blades.
Balance the turbine assembly (refer to CMM 29-21-45, ASSEMBLY).
Assemble the turbine-lower gearbox assembly as necessary (refer to
CMM 29-21-45, ASSEMBLY).
f  Do a test of the turbine-lower gearbox assembly (refer to CMM 29-21-45, TEST-
ING AND FAULT ISOLATION).
g  After all of the balance washer screws have been replaced, identify the turbine-
lower gearbox assembly as follows (refer to SPM 20-00-00, ASSEMBLY):
- Add the symbol 29-6 to a blank area of the identification plate (120 or
-120A, IPL Figure 1, CMM 29-21-45) or (120, IPL Figure 1A).
Proceed to paragraph 2.F. of this bulletin.
Jul 20/09  ERPS06G-29-6
Page 13
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 14 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
(e) If the balance washer inadvertently falls off after the screw is removed, install the balance
washer in its original installed orientation, as determined from the marking method used in
step 2.C. (4)(a) of this bulletin.
(f) While holding the balance washer in place, install a new screw MS24667-14. Torque the
screw 18 to 22 pound inches (2.1 to 2.4 Newton meters).
(g) Use a suitable temporary marking method (tape, indelible ink, or equivalent) to mark the
location where the balance washer screw has been replaced.
(h) Repeat steps 2.C. (4)(b) through (g) of this bulletin for each balance washer screw.
Remove any tape (that was used to mark the orientation of the installed balance washers
or the locations where the screws had been replaced).
(i) Remove the protective covering from the turbine-lower gearbox assembly turbine blades.
(5) After all of the balance washer screws have been replaced, identify the turbine-lower gearbox
assembly as follows (refer to SPM 20-00-00, ASSEMBLY):
(a) Add the symbol 29-6 to a blank area of the identification plate (120 or -120A, IPL Figure 1,
CMM 29-21-45) or (120, IPL Figure 1A).
D. Identification
NOTE:  After the screws have been replaced, the turbine-lower gearbox assembly is identified by
adding the symbol 29-6 to a blank area of the identification plate.
E. Test
(1) For units in the shop (if no balance washers were found missing, disassembly of the turbine was
not required, and the balance washer screws were replaced one screw at a time), a test of the
turbine-lower gearbox assembly is optional based on operator experience, normal shop prac-
tices and reason for removal (refer to CMM 29-21-45, TESTING AND FAULT ISOLATION).
Jul 20/09  ERPS06G-29-6
Page 14
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 15 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
F. Return Balance Washer Screws to Hamilton Sundstrand
(1) If the unit had a missing balance washer or a fractured screw, return all of the removed screws
(including the remnants of the fractured screw) to Hamilton Sundstrand for further investigation
as follows:
(a) Put the screws in a mailing package.
(b) Tag the screws (or include a note) to identify the part number and serial number of the tur-
bine-lower gearbox assembly that the screws were removed from and to identify the appli-
cable aircraft MSN.
(c) Return the screws with the applicable turbine-lower gearbox part number, turbine-lower
gearbox serial number, and aircraft MSN to the address that follows:
Hamilton Sundstrand Service Engineering
4747 Harrison Avenue
P.O. Box 7002
Rockford, IL 61125-7002
Attention: Greg Kuczek
Phone: +1- 815-226-6581
Fax: +1-860-660-4995
E-Mail: gregory.kuczek@hs.utc.com
G. Notification of Completion Form
(1) Do the following upon completion of this service bulletin:
(a) Make a copy of the "Notification of Completed SB ERPS06G-29-6" form (refer to Figure 2
of this bulletin), complete the form, and fax the completed form to Hamilton Sundstrand as
follows:
Hamilton Sundstrand Corporation
Retrofit Management Group
Fax: +1-860-998-3695
Jul 20/09  ERPS06G-29-6
Page 15
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 16 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
LOCATION OF RAT
IDENTIFICATION PLATE •
(DO NOT MARK)
(BALANCE WASHERS MAY BE
CIRCULAR OR RECTANGULAR)
SCREW  LOCATION OF BALANCE WASHERS
MS24667-14  ON THE REAR BALANCE PLANE
-(QUANTITY WILL VARY)
- LOCATION OF BALANCE WASHERS
ON THE FRONT BALANCE PLANE
LOCATION OF TURBINE-LOWER  (QUANTITY 12)
GEARBOX ASSEMBLY
766542 SERIES
IDENTIFICATION PLATE
SCREW
MS24667-14
(QUANTITY 12)  ~ LOCATION OF
TURBINE-LOWER
(BALANCE WASHERS MAY BE  GEARBOX ASSEMBLY
CIRCULAR OR RECTANGULAR)  1701401 SERIES  IDENTIFICATION PLATE
RAM AIR TURBINE MODULE 1702934 IS SHOWN  ERPS06G296-103946
RAT Module
Figure 1
Jul 20/09  ERPS06G-29-6
Page 16
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 17 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
NOTIFICATION OF COMPLETED SB ERPS06G-29-6
"Replace Balance Washer Screws"
SENT FROM:
Sender Name:
Sender Company:
Aircraft Operator:
Sender Fax #:
Send Date:
**PLEASE SUBMIT THIS NOTIFICATION SHEET WITHIN 10 DAYS AFTER MODIFICATION**
SEND TO:
Hamilton Sundstrand Corporation
Retrofit Management Group
Fax: +1-860-998-3695
Turbine-lower
Gearbox  Bulletin
Assembly  RAT  Aircraft MSN  Completion
Serial Number  Serial Number  or Tail Number  Date  Comments
Notification of Completion Form
Figure 2
60/02 1  ERPS06G-29-6
Page 17
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 18 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
3. Material Information
NOTE: Refer to Hamilton Sundstrand CMM 29-21-45 for expendable parts information.
Qty  Unit  Disposition/
New P/N  Per Unit  List Price  Key Word  Old P/N  Instructions
Same  RF  Not Applicable  Turbine-lower  766542 Series  Change and identify
(Note 1)  Gearbox  1701401 Series  (Note 2)
Assembly
Same  AR  (Note 4)  Screw  MS24667-14  Remove suspect old
(Note 3)  screws, install new
conforming screws
Note 1: Turbine-lower gearbox assemblies modified according to this service bulletin are identified by marking
the symbol 29-6 on the turbine-lower gearbox assembly identification plate.
Note 2: End item interchangeability is not affected.
Note 3: Operators should order a quantity of 18 screws for each unit for incorporation of this bulletin.
Note 4: Hamilton Sundstrand will supply the noted part at no charge (refer to paragraph 1.H. of this bulletin for
details).
Jul 20/09  ERPS06G-29-6
Page 18
Use or disclosure of this data is subject to restrictions on the front page of this document.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
