# Hamilton Sundstrand Service Bulletin ERPS08M-29-8

Copy: No revision named ("SB ERPS08M-29-8"), 18 pages: PDF https://openairdocs.org/files/sha256/04/b8/04b889254a8472ef1234b4f2e383e8942a087d611b7f1b2e41b93ac0dd5e56a6; text https://openairdocs.org/service-documents/hamilton-sundstrand/erps08m-29-8/file/04b889254a84.md. Rights: © Hamilton Sundstrand Corporation. Filed by the FAA in regulations.gov docket FAA-2011-0388; AD 2011-16-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Hamilton Sundstrand](https://openairdocs.org/service-documents/hamilton-sundstrand.md)
- Type: Service bulletin (Service Bulletin)
- Number: ERPS08M-29-8
- Page: https://openairdocs.org/service-documents/hamilton-sundstrand/erps08m-29-8

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2011-16-03](https://openairdocs.org/ad/2011-16-03.md), effective Sep 9, 2011: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/hamilton-sundstrand/erps08m-29-8/proposed.md).

## Text (18 pages)

Rights: © Hamilton Sundstrand Corporation. Filed by the FAA in regulations.gov docket FAA-2011-0388; AD 2011-16-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

Hamilton Sundstrand
A United Technologies Company
SERVICE BULLETIN
© 2009 Hamilton Sundstrand Corporation
PROPRIETARY
RECIPIENT  AGREES NOT TO DISCLOSE SUCH INFORMATION TONES OR TO OBTAIN FAA OR ANY OTHER GOVERNMENT OR REGULATORY APPROVAL  PEROR AD OTHER PURPOSE INCLUDING THE CREA TON OR AN OUTRE  NFORMATION TO ANY THIRD PARTY, EXCEPT AS MAY OTHERMSE BE PROVIDED FOR IN AN APPLICABLE
AGREEMENT BETWEEN RECIPIENT AND HSC.  COPYING OR DISCLOSURE OF  THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN BY ANYONE WITHOU
ISC'S PRIOR WRITTEN PERMISSION IS NOT AUTHORIZED AND MAY RESULT IN CRIMINAL AND/OR CIVIL LIABILITY
APPROVED BY HAMILTON SENDS AND THE PAT MAY NOT BE ALICATE ANY OTHER STEMS ANDER PARTS, REGARDLESS OF THEIR APPAREN  APPROVED BY HAMILTON SUNDSTRAND
SIMILARITY TO SYSTEMS AND/OR PARTS MANUFACTURED BY OR FOR HAMILTON SUNDSTRAND OR APPROVED BY HAMILTON SUNDSTRAND. DO NOT RELY IN AN
NAY ON DATA IN THIS DOCUMENT TO MAINTAIN OR OTHERWISE SUPPORT SYSTEMS AND/OR PARTS THAT WERE NOT MANUFACTURED BY OR FOR HAMILTON
SUNDSTRAND OR APPROVED BY HAMILTON SUNDSTRAND WITHOUT EVIDENCE THAT THE FEDERAL AVIATION ADMINISTRATION OR OTHER REGULATORY AGENCY
HAS DETERMINED THAT THE DATA IN THIS DOCUMENT IS VALID FOR SUCH USE
Information Subject to Export Control Laws
THE TECHNICAL DATA IN THIS DOCUMENT (OR FILE) IS CONTROLLED FOR EXPORT UNDER THE EXPORT ADMINISTRATION REGULATIONS (EAR), 15 CER PARTS 730
74, ECCN: 9E991, VIOLATIONS OF THESE LAWS MAY BE SUBJECT TO FINES AND PENALTIES UNDER THE EXPORT ADMINISTRATION ACT
Emergency Hydraulic Power - Ram Air Turbine - Replace Balance Weight/Washer Screws
1.  Planning Information
A. Effectivity
The Hamilton Sundstrand Ram Air Turbines (RAT), Model ERPS08M, that are listed below and used
on Airbus A318, A319, A320, and A321 aircraft.
Part Number
Series  Serial Numbers
762308  0102, 0163, 0173, 0181, 0192, 0252, 0272, 0275, 0287, 0289, 0295, 0340, 0341, 0343
766352  057,072, 07, 0512,085  0006, 0367, 0371, 0373, 0384, 0398, 0403, 0407, 0421, 0425, 0434, 0465, 0490, 0530,  0568, 0591, 0596, 0617, 0631, 0651, 0677, 0684, 0685, 0691, 0692, 0697, 0709, 0716,
0724, 0731, 0734, 0742, 0763, 0770, 0771, 0787, 0797, 0804, 0816, 0823, 0833, 0855,
0871, 0879, 0917, 0931, 0979, 0984, 1004, 1011, 1035, 1046, 1051, 1096, 1168, 1178,
1184, 1186, 1207, 1221, 1237, 1239, 1265, 1278, 1286, 1302, 1309, 1325, 1333, 1370,
1429, 1446, 1453, 1476, 1493, 1574, 1581, 1588, 1602, 1609, 1630, 1644, 1672, 1714,
1764, 1810, 1874, 1940, 2009, 2019, 2046, 2140, 2159, 2164, 2242, 2258, 2409, 2497,
2511, 2607, 2636, 2637, 2653, 2657, 2662, 2674, 2684, 2690, 2692, 2696, 2699, 2700,
2701, 2702, 2703, 2704, 2705, 2706, 2707, 2708, 2709, 2710, 2711, 2712, 2713, 2714,
2715, 2716, 2717, 2718, 2719, 2720, 2721, 2722, 2723, 2724, 2725, 2726, 2727, 2728,
2729, 2730, 2731, 2732, 2733, 2734, 2735, 2736, 2737, 2738, 2739, 2740, 2741, 2742,
2743, 2744, 2745, 2746, 2747, 2748, 2749, 2750, 2751, 2752, 2753, 2754, 2755, 2756,
2757, 2758, 2759, 2760, 2761, 2762, 2763, 2764, 2765, 2766, 2767, 2768, 2769, 2770,
2771, 2772, 2773, 2774, 2775, 2776, 2777, 2778, 2779, 2780, 2781, 2782, 2783, 2784,
2785, 2786, 2787, 2788, 2789  , 2790  ), 2791, 2792, 2793, 2794, 2795, 2796, 2797, 2798,
2799, 2800, 2801, 2802, 2803, 2804, 2805, 2806, 2807, 2808, 2809, 2810, 2811, 2812,
2813, 2814, 2815, 2816, 2817, 2818, 2819, 2820, 2821, 2822, 2823, 2824, 2825, 2826,
2827, 2828, 2829, 2830, 2831, 2832, 2833, 2834, 2835, 2836, 2837, 2838, 2839, 2840,
2841, 2842, 2843, 2844, 2845, 2846, 2847, 2848, 2849, 2850, 2851, 2852, 2853, 2854,
2855, 2856, 2857, 2858, 2859, 2860, 2861, 2862, 2863, 2864, 2865, 2866, 2867, 2868,
2869, 2870, 2871, 2872, 2873, 2874, 2875, 2876, 2877, 2878, 2879, 2880, 2881, 2882,
2883, 2884, 2885, 2886, 2887, 2888, 2889, 2890, 2891,  2892, 2893, 2894, 2895, 2896,
2897, 2898, 2899, 2900, 2901, 2902, 2903, 2904, 2905, 2906, 2907, 2908, 2909, 2910,
(continued on the next page)
Jun 17/09  ERPS08M-29-8
Page 1 of 18

### Page 2 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
Part Number
Series  Serial Numbers
766352  (continued from the previous page)
2911, 2912, 2913, 2914, 2915, 2916, 2917, 2918, 2919, 2920, 2921, 2922, 2923, 2924
2925, 2926, 2927, 2928, 2929, 2930, 2931, 2932,  2933, 2934, 2935, 2936, 2937, 2938,
2939, 2940, 2941, 2942, 2943, 2944, 2945, 2946, 2947, 2948, 2949, 2950, 2951, 2952
2953, 2954, 2955, 2956, 2957, 2958, 2959, 2961, 2962, 2963, 2964, 2965, 2966, 2967
2968, 2969, 2970, 2971, 2972, 2973, 2974  2975  2976, 2977, 2978, 2979, 2980, 2981
2982, 2983, 2984, 2985, 2986, 2987, 2988,  2989,  2990, 2991, 2992, 2993, 2994, 2995,
2996, 2997, 2998, 2999, 3000, 3002, 3003  3004,  3005, 3006, 3007, 3008, 3009, 3010,
3011, 3012, 3013, 3014, 3015, 3016, 3017, 3018, 3019, 3020, 3021, 3022, 3023, 3024
3025, 3026, 3027, 3028, 3029, 3030, 3031, 3032, 3033, 3034, 3035, 3036, 3037, 3038,
3039, 3040, 3041, 3042, 3043, 3044, 3045, 3046, 3047, 3048, 3049, 3050, 3051, 3052,
3053, 3054, 3055, 3056, 3057, 3058, 3059, 3060, 3061, 3062, 3063, 3064, 3065, 3066,
3067, 3068, 3069, 3070, 3071, 3072, 3073, 3074, 3075, 3076, 3077, 3078, 3079, 3080,
3081, 3082, 3083, 3084, 3085, 3086, 3087, 3088, 3089, 3090, 3091, 3092, 3093, 3094,
3095, 3096, 3097, 3098, 3099, 3100, 3101, 3102, 3103, 3104, 3105, 3106, 3107, 3108,
3109, 3110, 3111, 3112, 3113, 3114, 3115, 3116, 3117, 3118, 3119, 3120, 3121, 3122,
3123, 3124, 3125, 3126, 3127, 3128, 3129, 3130, 3131, 3132, 3133, 3134, 3135, 3136,
3137, 3138, 3139, 3140, 3141, 3142, 3143, 3145, 3146, 3147, 3148, 3149, 3150, 3151,
3152, 3153, 3154, 3155, 3156, 3157, 3158, 3159, 3160, 3161, 3162, 3164, 3166, 3167,
3169, 3170, 3171, 3172, 3173, 3175, 3176, 3177, 3178, 3179, 3180, 3182, 3183, 3184,
3185, 3186, 3187, 3188, 3189, 3190, 3191, 3192, 3194, 3195, 3196, 3198, 3199, 3200,
3201, 3202, 3204, 3205, 3206, 3207, 3208, 3209, 3211, 3212, 3213, 3214, 3215, 3216,
3217, 3219, 3220, 3221, 3223, 3224, 3225, 3227, 3229, 3230, 3231, 3232, 3233, 3235,
3236, 3239, 3241, 3242, 3244, 3245, 3246, 3247, 3249, 3252, 3253, 3255, 3256, 3257,
3258, 3259, 3260, 3263, 3264, 3266
B. Concurrent Requirements
None. *
C. Reason
Hamilton Sundstrand has discovered that RATs were manufactured with nonconforming screws. To
date, there have been five instances of a fractured balance weight/washer screw on multiple RAT
part number configurations. Fracture of a balance weight/washer screw can result in the loss of the
associated balance weight/washer and create an unacceptable turbine imbalance. Inspection of
other screws in Hamilton Sundstrand stock revealed metallographic nonconformities consistent with
those of the fractured screws. The suspect screws have been isolated to a lot from a specific sup-
plier. Analysis indicates the nonconformance could be a result of the supplier's heat treat process,
which increases susceptibility to brittle fracture. Replacement of the suspect screws with confirmed
conforming screws will eliminate potential loss of a balance weight/washer. Incorporation of this bul-
letin will ensure that the RAT balance weight/washer screws conform to specification.
Jun 17/09  ERPS08M-29-8
Page 2
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 3 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
D. Description
This bulletin gives instructions to replace the balance weight or washer screws and identify the RAT.
For a RAT with a missing balance weight/washer, or with a balance weight/washer screw that cannot
be removed in its entirety, instructions are also given to disassemble the RAT as necessary to
remove the fractured screw and balance weight or washer, balance the turbine assembly, assemble
the RAT, and test the RAT.
E. Compliance
Incorporation of this service bulletin is to be accomplished at the earliest opportunity.
F. Approval
This service bulletin contains no modification information that revises the approved configuration and
therefore does not require Federal Aviation Administration (FAA) or other regulatory agency
approval.
G. Manpower
A maximum of 0.5 man-hour will be required to replace the balance weight/washer screws and iden-
tify the RAT.
For a RAT with a missing balance weight/washer, or with a balance weight/washer screw that cannot
be removed in its entirety, a maximum of 9.0 man-hours will be required to disassemble the RAT as
necessary to remove the fractured screw and balance weight or washer, balance the turbine assem-
bly, assemble the RAT, and test the RAT.
H. Material - Cost and Availability
(1) Hamilton Sundstrand will supply replacement parts on a no charge basis until August 10, 2010.
Replacement parts are currently available in limited quantities. Operators approved by Hamilton
Sundstrand to perform modification of units at their facility should place a single "no charge"
order to Hamilton Sundstrand. Operators can forward these orders to their assigned Hamilton
Sundstrand Commercial Spares Administrator (or fax to +1-815-226-2624, if the responsible
Administrator is not known). In addition, operators can also use the Hamilton Sundstrand web-
site at www.hamiltonsundstrand.com to contact the Commercial Spares group. Upon entering
the website, select "Customer Service" followed by "Commercial Spares" for other contact and
order processing options that are available. Orders must clearly reference fleet requirements,
noting the service bulletin number, serial numbers of affected units, total quantity of parts, and
anticipated incorporation schedule (refer to paragraph 3. for the parts breakdown). Hamilton
Sundstrand will acknowledge the operator order with an established delivery rate.
(2) Hamilton Sundstrand will also give the following:
(a)  A maximum labor allowance of 0.5 man-hour multiplied by the operator's current approved
hourly rate for accomplishment of this service bulletin in the shop. The labor allowance will
expire August 10, 2010.
(b) A maximum labor allowance of 0.5 man-hour multiplied by the operator's current approved
hourly rate for replacement of the balance weight/washer screws on the aircraft. The labor
allowance will expire August 10, 2010.
Jun 17/09  ERPS08M-29-8
Page 3
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 4 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
(c) If removal from the aircraft is required, a maximum labor allowance of 6.0 man-hours multi-
plied by the operator's current approved hourly rate for replacement of the RAT on the air-
craft and test on wing. The labor allowance will expire August 10, 2010.
(d)  Operators should forward a claim for labor reimbursement to their assigned Hamilton
Sundstrand Rockford Warranty Administrator. If the responsible Administrator is not
known, the claim should be mailed to Warranty Administration, 4747 Harrison Ave, Rock-
ford, IL 61126, USA, MS 106-6. The claim should reference the service bulletin number,
serial numbers modified, date modified, total hours, and approved labor rate.
(3)  For units with a missing balance weight/washer, or with a balance weight/washer screw that
cannot be removed in its entirety, Hamilton Sundstrand will incorporate this modification into
returned units at no charge until August 10, 2010. Contact Hamilton Sundstrand at the address
that follows for scheduling information:
Hamilton Sundstrand
4747 Harrison Avenue
P.O. Box 7002
Rockford, IL 61125-7002
Attention: Repair Administration
Mail Stop 151-6
Telephone: +1-815-226-6849
Fax: 815-394-2414
Tooling - Price and Availability
No tooling other than that required for shop maintenance of the RAT is required to do this modifica-
tion.
J. Weight and Balance
None.
K. Electrical Load Data
Not changed.
L. References
Applicable Aircraft Maintenance Manual (AMM), Hamilton Sundstrand Component Maintenance
Manuals (CMM) 29-21-42 and 29-21-44, and Hamilton Sundstrand Standard Practices Manual
(SPM) 20-00-00.
M. Other Publications Affected
Hamilton Sundstrand MMs 29-21-42 and 29-21-44 will be revised to incorporate this service bulle-
tin.
Jun 17/09  ERPS08M-29-8
Page 4
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 5 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
2. Accomplishment Instructions
A. General
CAUTION:  THE RAT CONTAINS DESIGN CRITICAL CHARACTERISTICS, PROCESSES, AND
PROCEDURES. THE DESIGN CRITICAL CHARACTERISTICS ARE IDENTIFIED
WITH THE SYMBOL >>DCC<<. REFER TO THE INTRODUCTION SECTION OF
CMM 29-21-42 OR CMM 29-21-44 FOR A COMPLETE EXPLANATION OF DESIGN
CRITICAL CHARACTERISTICS.
(1) The user should obtain the material safety data sheets [Occupational Safety and Health Act
(OSHA) Form 20 or equivalent] from the manufacturers or suppliers of materials to be used.
The user must become completely familiar with the manufacturer/supplier information and
adhere to the procedures, recommendations, warnings, and cautions of the manufacturer/sup-
plier for the safe use, handling, storage, and disposal of these materials. The user should also
read the long version of the warnings contained in this service bulletin. The long version warn-
ings are contained in Hamilton Sundstrand Warnings Registry 341-006 available free of charge
to all organizations that are on distribution for this Service Bulletin. The Warnings Registry
341-006 is also available at www.hsvas.com.
B. Modification - On the Aircraft
(1) Make sure the RAT is deployed (refer to the applicable AMM).
CAUTION: THE RAT TURBINE BLADE SHOULD BE PROTECTIVELY COVERED DURING BAL-
ANCE WEIGHT/WASHER SCREW REMOVAL AND INSTALLATION. THE BLADES
CAN BE EASILY DAMAGED.
(2) Install a protective covering on the RAT turbine blades to prevent damage to the blades from
contact with the tooling or screws.
(3) Rotate the turbine assembly and do a check for missing balance weights and washers (refer to
Figure 1 or 2 of this bulletin for the location of the balance weights/washers).
NOTE: The number of balance weights/washers installed will vary according to the magnitude
of the imbalance that existed before the turbine assembly was balanced.
- The threaded holes around the turbine circumference that are not used for bal-
ance weights/washers have a set screw installed. The set screw is secured
using a 5/64-inch internal hex tool. The set screws should not be removed or
replaced.
- The threaded holes around the turbine circumference with balance weights/
washers installed, use a countersunk socket head cap screw MS24667-14 to
secure the weights/washers.
NOTE:  Missing balance weights/washers are evidenced by the remaining screw and primer
residue (in a rectangular or circular shaped pattern) on the turbine assembly (refer to
Figure 3 of this bulletin).
(4) If any balance weights/washers are missing (because of a fractured screw), the RAT must be
removed from the aircraft (refer to the applicable AMM) for removal of the fractured screw and
to balance the turbine assembly. The RAT must either be returned to Hamilton Sundstrand or to
a repair facility that has the capability to disassemble, repair, balance, and test the RAT.
Jun 17/09  ERPS08M-29-8
Page 5
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 6 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
CAUTION:  REPLACE THE BALANCE WEIGHT/WASHER SCREWS ONE AT A TIME. DO NOT
REMOVE ALL OF THE SCREWS AT THE SAME TIME. IF MORE THAN ONE SCREW
IS REMOVED AT A TIME, THE TURBINE ASSEMBLY MUST BE RE-BALANCED.
(5) If no balance weights/washers are missing, do the steps that follow to replace the balance
weight/washer screws (one at a time):
(a) For each balance washer that is unsymmetrical in shape, use a suitable temporary mark-
• ing method (tape, indelible ink, or equivalent) to mark the radial orientation of the installed
balance washer. The original installed radial orientation of the washer must be maintained.
NOTE: If a balance washer is circular in shape, it is not necessary to mark its radial orien-
tation.
(b) Rotate the turbine assembly until the balance weight/washer is positioned in a manner to
minimize the potential for the balance weight/washer to fall out (when the associated screw
is removed).
CAUTION: DO NOT USE A WORN INTERNAL HEX TOOL WITH ROUNDED CORNERS TO
REMOVE THE SCREW. IF A WORN TOOL IS USED, THE POTENTIAL EXISTS
FOR STRIPPING THE SOCKET HEAD OF THE SCREW.
CAUTION:  USE CARE NOT TO DAMAGE EITHER THE BALANCE WEIGHT/WASHER OR
TURBINE ASSEMBLY IF IT IS NECESSARY TO STRIKE THE HEAD OF THE
SCREW BECAUSE THE BREAK-AWAY TORQUE IS EXCESSIVE.
(c) While holding the balance weight/washer in place, use a 3/32-inch internal hex tool to
remove one screw from one balance weight/washer.
NOTE: The use of a hex insert bit is preferred.
NOTE: If the screw break-away torque is excessive, it is permissible to lightly strike the
head of the screw using a small hammer and a 5/16-inch (8-millimeter) pin punch.
It should not be necessary to strike more than two times.
(a)  If the screw is fractured (with the balance weight/washer installed) or if a screw fractures
during removal, do the steps that follow to remove the remaining portion of the screw:
1 Report any occurrences of a fractured screw to Hamilton Sundstrand as follows:
Greg Kuczek
Hamilton Sundstrand Service Engineering
Phone: +1- 815-226-6581
Fax: +1-860-660-4995
E-Mail: gregory.kuczek@hs.utc.com
2  If the remaining portion of the fractured screw is protruding above the turbine surface,
do the steps that follow:
Apply protective tape on the turbine (in the area of the screw) to prevent surface
damage during the removal attempt.
Use pliers, a vice grip, or an equivalent gripping tool to remove the screw.
Jun 17/09  ERPS08M-29-8
Page 6
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 7 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
C Remove the protective tape from the turbine.
g If the screw is removed in its entirety, proceed to step 2.B. (5)(e) of this bulletin.
If the remaining portion of the screw is flush or below the turbine surface, or if the
screw can not be removed in its entirety, do the steps that follow:
NOTE: Hamilton Sundstrand recommends the RAT be removed from the aircraft
(refer to the applicable AMM) for the removal of the fractured screw. The
RAT should either be returned to Hamilton Sundstrand or to a repair facility
that has the capability to disassemble, repair, balance, and test the RAT.
However, as an option, and at the operator's discretion, an attempt to
mechanically extract a screw while the RAT is installed on the aircraft is
allowed.
The procedure to mechanically extract a fractured screw, or one with a
stripped socket head, must not use any heat or fluid. Care must be taken to
make sure no filings or fragments enter the turbine assembly.
The turbine hub and turbine blades should be protectively covered to prevent
mechanically induced damage during the extraction procedure.
The self-locking screw thread insert should be visually inspected (after the
screw is extracted) to make sure there is no mechanical damage.
Some screws, depending on how near they are to a turbine blade, can not be
extracted unless the turbine blades are disassembled from the turbine
assembly. In those cases, the RAT must be removed from the aircraft and
disassembled as necessary to remove the screw.
a  Use a screw extractor (or equivalent) to remove the remaining portion of the frac-
tured screw. Make sure no filings or fragments enter the turbine assembly. Do not
use heat or fluid to remove the screw.
NOTE: If the screw can not be extracted, the RAT must be removed from the
aircraft (refer to the applicable AMM) and disassembled as necessary to
remove the fractured screw. The RAT should either be returned to
Hamilton Sundstrand or to a repair facility that has the capability to dis-
assemble, repair, balance, and test the RAT.
Do a visual check of the self-locking screw thread insert to make sure there is no
mechanical damage.
(e)  If the balance weight/washer inadvertently falls off after the screw is removed, install the
balance weight/washer in its original installed orientation, as determined from the marking
method used in step 2.B.(5)(a) of this bulletin.
(f) While holding the balance weight/washer in place, install a new screw MS24667-14.
Torque the screw 16 to 20 pound inches (1.9 to 2.2 Newton meters).
NOTE: It is not necessary to remove the existing primer residue or apply new primer if the
balance weight/washer inadvertently fell off after the screw was removed.
Jun 17/09  ERPS08M-29-8
Page 7
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 8 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
(g) Use a suitable temporary marking method (tape, indelible ink, or equivalent) to mark the
location where the balance weight/washer screw has been replaced.
(h) Repeat steps 2.B.(5)(b) through (g) of this bulletin for each balance weight/washer screw.
(i) Remove any tape (that was used to mark the orientation of the installed balance weights/
washers or the locations where the screws had been replaced).
Remove the protective covering from the RAT turbine blades.
(6) After all of the balance weight/washer screws have been replaced, identify the RAT as follows:
(a) Engrave or vibro-etch the symbol 29-8 on a blank area of the RAT nameplate or identifica-
tion plate (refer to Figure 1 or 2 of this bulletin for the location of the RAT nameplate or
identification plate).
(7) Make sure the RAT is re-stowed (refer to the applicable AMM).
(8) Proceed to paragraph 2.F. of this bulletin.
C. Modification - In the Shop
CAUTION:  THE RAT TURBINE BLADE SHOULD BE PROTECTIVELY COVERED DURING BAL-
ANCE WEIGHT/WASHER SCREW REMOVAL AND INSTALLATION. THE BLADES
CAN BE EASILY DAMAGED.
(1) Install a protective covering on the RAT turbine blades to prevent damage to the blades from
contact with the tooling or screws.
(2) Rotate the turbine assembly and do a check for missing balance weights and washers (refer to
Figure 1 or 2 of this bulletin for the location of the following balance weights/washers):
- Balance weights or washers (10 or -10A, IPL Figure 4, CMM 29-21-42), (15),
and (20, -20A, -20B, or -20C)
- Balance weights or washers (10 or -10A, IPL Figure 4, CMM 29-21-44), (20),
and (30, -30A, -30B, or -30C).
NOTE: The number of balance weights/washers installed will vary according to the magnitude
of the imbalance that existed before the turbine assembly was balanced.
- The threaded holes around the turbine circumference that are not used for bal-
ance weights/washers have a set screw installed. The set screw is secured
using a 5/64-inch internal hex tool. The set screws should not be removed or
replaced.
- The threaded holes around the turbine circumference with balance weights/
washers installed, use a countersunk socket head cap screw MS24667-14 to
secure the weights/washers [refer to screw (30, IPL Figure 4, CMM 29-21-42) or
(40, IPL Figure 4, CMM 29-21-44)).
NOTE:  Missing balance weights/washers are evidenced by the remaining screw and primer
residue (in a rectangular or circular shaped pattern) on the turbine assembly (refer to
Figure 3 of this bulletin).
Jun 17/09  ERPS08M-29-8
Page 8
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 9 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
(3) If any balance weights/washers are missing (because of a fractured screw), do the steps that
follow:
(a) Report any occurrences of a fractured screw to Hamilton Sundstrand as follows:
Greg Kuczek
Hamilton Sundstrand Service Engineering
Phone: +1- 815-226-6581
Fax: +1-860-660-4995
E-Mail: gregory.kuczek@hs.utc.com
(b) Disassemble the RAT (refer to CMM 29-21-42 or 29-21-44, DISASSEMBLY) as necessary
to remove the following parts and to get access to the fractured screw.
- Balance weights or washers
(10 or -10A, IPL Figure 4, CMM 29-21-42), (15), and (20, -20A, -20B, or -20C)
or (10 or -10A, IPL Figure 4, CMM 29-21-44), (20), and (30, -30A, -30B, or -30C)
- Screws (30, IPL Figure 4, CMM 29-21-42) or (40, IPL Figure 4, CMM 29-21-44)
Some screws, depending on how near they are to a turbine blade, can not be
extracted unless the turbine blades are disassembled from the turbine assembly.
In those cases, the RAT must be disassembled as necessary to remove the
screw.
(c) Use a screw extractor (or equivalent) to remove the remaining portion of the fractured
screw. Make sure no filings or fragments enter the turbine assembly. Do not use heat or
fluid to remove the screw.
(d)  Do a visual check of the self-locking screw thread insert to make sure there is no mechani-
cal damage.
(e) Assemble the turbine assembly as necessary (refer to CMM 29-21-42 or 29-21-44,
ASSEMBLY).
(f) Remove the protective covering from the RAT turbine blades.
(g) Balance the turbine assembly (refer to CMM 29-21-42 or 29-21-44, ASSEMBLY).
(h) Assemble the RAT as necessary (refer to CMM 29-21-42 or 29-21-44, ASSEMBLY).
(i) Do a test of the RAT (refer to CMM 29-21-42 or 29-21-44, TESTING AND FAULT ISOLA-
TION).
() After all of the balance weight/washer screws have been replaced, identify the RAT as fol-
lows (refer to SPM 20-00-00, ASSEMBLY):
1  Add the symbol 29-8 to a blank area of the RAT nameplate (550, IPL Figure 1,
CMM 29-21-42) or identification plate (-410A, -410B, or -410C, IPL Figure 1,
CMM 29-21-44).
(k) Proceed to paragraph 2.F. of this bulletin.
Jun 17/09  ERPS08M-29-8
Page 9
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 10 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
CAUTION:  REPLACE THE BALANCE WEIGHT/WASHER SCREWS ONE AT A TIME. DO NOT
REMOVE ALL OF THE SCREWS AT THE SAME TIME. IF MORE THAN ONE SCREW
IS REMOVED AT A TIME, THE TURBINE ASSEMBLY MUST BE RE-BALANCED.
(4) If no balance weights/washers are missing, do the steps that follow to replace the balance
weight/washer screws (one at a time):
(a) For each balance washer that is unsymmetrical in shape, use a suitable temporary mark-
ing method (tape, indelible ink, or equivalent) to mark the radial orientation of the installed
balance washer. The original installed radial orientation of the washer must be maintained.
NOTE: If a balance washer is circular in shape, it is not necessary to mark its radial orien-
tation.
(b) Position the unit to access the balance weight/washer facing up.
CAUTION: DO NOT USE A WORN INTERNAL HEX TOOL WITH ROUNDED CORNERS TO
REMOVE THE SCREW. IF A WORN TOOL IS USED, THE POTENTIAL EXISTS
FOR STRIPPING THE SOCKET HEAD OF THE SCREW.
CAUTION:  USE CARE NOT TO DAMAGE EITHER THE BALANCE WEIGHT/ASHER OR
TURBINE ASSEMBLY IF IT IS NECESSARY TO STRIKE THE HEAD OF THE
SCREW BECAUSE THE BREAK-AWAY TORQUE IS EXCESSIVE.
(c) While holding the balance weight/washer in place, use a 3/32-inch internal hex tool to
remove one screw from one balance weight/washer.
NOTE: The use of a hex insert bit is preferred.
NOTE: If the screw break-away torque is excessive, it is permissible to lightly strike the
head of the screw using a small hammer and a 5/16-inch (8-millimeter) pin punch.
It should not be necessary to strike more than two times.
(d) If the screw is fractured (with the balance weight/washer installed) or if a screw fractures
during removal, do the steps that follow to remove the remaining portion of the screw:
1  Report any occurrences of a fractured screw to Hamilton Sundstrand as follows:
Greg Kuczek
Hamilton Sundstrand Service Engineering
Phone: +1- 815-226-6581
Fax: +1-860-660-4995
E-Mail: gregory.kuczek@hs.utc.com
2  If the remaining portion of the fractured screw is protruding above the turbine surface,
do the steps that follow:
Apply protective tape on the turbine (in the area of the screw) to prevent surface
damage during the removal attempt.
Use pliers, a vice grip, or an equivalent gripping tool to remove the screw.
Remove the protective tape from the turbine.
Jun 17/09  ERPS08M-29-8
Page 10
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 11 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
d If the screw is removed in its entirety, proceed to step 2.C.(4)(e) of this bulletin.
If the remaining portion of the screw is flush or below the turbine surface, or if the
screw can not be removed in its entirety, do the steps that follow:
NOTE:  The procedure to mechanically extract a fractured screw, or one with a
stripped socket head, must not use any heat or fluid. Care must be taken to
make sure no filings or fragments enter the turbine assembly.
The turbine hub and turbine blades should be protectively covered to prevent
mechanically induced damage during the extraction procedure.
The self-locking screw thread insert should be visually inspected (after the
screw is extracted) to make sure there is no mechanical damage.
a Disassemble the RAT (refer to CMM 29-21-42 or 29-21-44, DISASSEMBLY) as
necessary to get access to the fractured screw.
NOTE: Some screws, depending on how near they are to a turbine blade, can
not be extracted unless the turbine blades are disassembled from the
turbine assembly. In those cases, the RAT must be disassembled as
necessary to remove the screw.
Use a screw extractor (or equivalent) to remove the remaining portion of the frac-
tured screw. Make sure no filings or fragments enter the turbine assembly. Do not
use heat or fluid to remove the screw.
Do a visual check of the self-locking screw thread insert to make sure there is no
mechanical damage.
4  If disassembly of the turbine assembly was not required to remove the fractured
screw, proceed to step 2.C.(4)(e) of this bulletin.
If disassembly of the turbine assembly was required to remove the fractured screw, do
the following:
a  Remove the remaining screws (30, IPL Figure 4, CMM 29-21-42) or (40, IPL Fig-
ure 4, CMM 29-21-44) and the following balance weights/washers:
- Balance weights or washers (10 or -10A, IPL Figure 4, CMM 29-21-42),
(15), and (20, -20A, -20B, or -20C)
or (10 or -10A, IPL Figure 4, CMM 29-21-44), (20),
and (30, -30A, -30B, or -30C)
Assemble the turbine assembly as necessary (refer to CMM 29-21-42 or
29-21-44, ASSEMBLY).
Remove the protective covering from the RAT turbine blades.
d Balance the turbine assembly (refer to CMM 29-21-42 or 29-21-44, ASSEMBLY)
Assemble the RAT as necessary (refer to CMM 29-21-42 or 29-21-44, ASSEM-
BLY).
Jun 17/09  ERPS08M-29-8
Page 11
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 12 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
Do a test of the RAT (refer to CMM 29-21-42 or 29-21-44, TESTING AND FAULT
ISOLATION).
g  After all of the balance weight/washer screws have been replaced, identify the
RAT as follows (refer to SPM 20-00-00, ASSEMBLY):
- Add the symbol 29-8 to a blank area of the RAT nameplate (550, IPL Fig-
ure 1, CMM 29-21-42) or identification plate (-410A, -410B, or -410C,
IPL Figure 1, CMM 29-21-44).
Proceed to paragraph 2.F. of this bulletin.
(e) If the balance weight/washer inadvertently falls off after the screw is removed, install the
balance weight/washer in its original installed orientation, as determined from the marking
method used in step 2.C. (4)(a) of this bulletin.
(f) - While holding the balance weight/washer in place, install a new screw MS24667-14.
Torque the screw 16 to 20 pound inches (1.9 to 2.2 Newton meters).
NOTE: It is not necessary to remove the existing primer residue or apply new primer if the
balance weight/washer inadvertently fell off after the screw was removed.
(g)  Use a suitable temporary marking method (tape, indelible ink, or equivalent) to mark the
location where the balance weight/washer screw has been replaced.
(h). Repeat steps 2.C. (4)(b) through (g) of this bulletin for each balance weight/washer screw.
(i) Remove any tape (that was used to mark the orientation of the installed balance weights/
washers or the locations where the screws had been replaced).
() Remove the protective covering from the RAT turbine blades.
(5) After all of the balance weight/washer screws have been replaced, identify the RAT as follows
(refer to SPM 20-00-00, ASSEMBLY):
(a)  Add the symbol 29-8 to a blank area of the RAT nameplate (550, IPL Figure 1,
CMM 29-21-42) or identification plate (-410A, -410B, or -410C, IPL Figure 1,
CMM 29-21-44).
D. Identification
NOTE: After all of the balance weight/washer screws have been replaced, the RAT is identified by
adding the symbol 29-8 to a blank area of the RAT nameplate or identification plate.
E.  Test
(1) For units in the shop (if no balance weights/washers were found missing, disassembly of the
turbine was not required, and the balance weight/washer screws were replaced one screw at a
time), a test of the RAT is optional based on operator experience, normal shop practices, and
reason for removal (refer to CMM 29-21-42 or 29-21-44, TESTING AND FAULT ISOLATION).
Jun 17/09  ERPS08M-29-8
Page 12
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 13 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
F. Return Balance Weight/Washer Screws to Hamilton Sundstrand
(1) If the unit had a missing balance weight/washer or a fractured screw, return all of the removed
screws (including the remnants of the fractured screw) to Hamilton Sundstrand for further inves-
tigation as follows:
(a) Put the screws in a mailing package.
(b) Tag the screws (or include a note) to identify the part number and serial number of the RAT
the screws were removed from and to identify the applicable aircraft MSN.
(c) Return the screws with the applicable RAT part number, RAT serial number, and aircraft
MSN to the address that follows:
Hamilton Sundstrand Service Engineering
4747 Harrison Avenue
P.O. Box 7002
Rockford, IL 61125-7002
Attention: Greg Kuczek
Phone: +1- 815-226-6581
Fax: +1-860-660-4995
E-Mail: gregory.kuczek@hs.utc.com
G. Notification of Completion Form
(1) Do the following upon completion of this service bulletin:
(a) Make a copy of the "Notification of Completed SB ERPS08M-29-8" form (refer to Figure 4
of this bulletin), complete the form, and fax the completed form to Hamilton Sundstrand as
follows:
Hamilton Sundstrand Corporation
Retrofit Management Group
Fax: +1-860-998-3695
Jun 17/09  ERPS08M-29-8
Page 13
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 14 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
LOCATION OF RAT
NAMEPLATE
LOCATION OF BALANCE
WEIGHTS OR WASHERS
(QUANTITY WILL VARY)  (BALANCE WEIGHTS AND
WASHERS MAY BE
CIRCULAR OR RECTANGULAR)
SCREW
MS24667-14
ERPS08M298-103844
RAT 762308 Series
Figure '
60/21 unr  ERPS08M-29-8
Page 14
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 15 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
- LOCATION OF RAT
IDENTIFICATION PLATE
LOCATION OF BALANCE
WEIGHTS OR WASHERS
(QUANTITY WILL VARY)  (BALANCE WEIGHTS AND
WASHERS MAY BE
CIRCULAR OR RECTANGULAR)
SCREW
MS24667-14
ERPS08M298-103843
RAT 766352 Series
Figure 2
Jun 17/09  ERPS08M-29-8
Page 15
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 16 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
Missing Balance Weight/Washer
Figure 3
Jun 17/09  ERPS08M-29-8
Page 16
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 17 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
NOTIFICATION OF COMPLETED SB ERPS08M-29-8
"Replace Balance Weight/Washer Screws"
SENT FROM:
Sender Name:
Sender Company:
Aircraft Operator:
Sender Fax #:
Send Date:
**PLEASE SUBMIT THIS NOTIFICATION SHEET WITHIN 10 DAYS AFTER MODIFICATION**
SEND TO:
Hamilton Sundstrand Corporation
Retrofit Management Group
Fax: +1-860-998-3695
RAT  Aircraft MSN  Bulletin
Serial Number  or Tail Number  Completion Date  Comments
Notification of Completion Form
Figure 4
60/21 unr  ERPS08M-29-8
Page 17
Use or disclosure of this data is subject to restrictions on the front page of this document.

### Page 18 (OCR)

HAMILTON SUNDSTRAND
SERVICE BULLETIN
3. Material Information
NOTE: Refer to Hamilton Sundstrand CMMs 29-21-42 and 29-21-44 for expendable parts information.
Qty
Per  Unit  Disposition/
New P/N  Unit  List Price  Key Word  Old P/N  Instructions
Same  Not Applicable  Ram Air Turbine  766352 Series  Change and identify
(Note 1)  762308 Series  (Note 2)
Same  AR  (Note 4)  Screw  MS24667-14  Remove suspect old
(Note 3)  screws, install new
conforming screws
Note 1: RATs modified according to this service bulletin are identified by marking the symbol 29-8 on the RAT
nameplate or identification plate.
Note 2: End item interchangeability is not affected.
Note 3: Operators should order a quantity of 10 screws for each unit for incorporation of this bulletin.
Note 4: Hamilton Sundstrand will supply the noted part at no charge (refer to paragraph 1.H. of this bulletin for
details).
Jun 17/09  ERPS08M-29-8
Page 18
Use or disclosure of this data is subject to restrictions on the front page of this document.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
