# Ipeco Service Bulletin 063-25-20: Revision 1

- Rights: © Ipeco Holdings Ltd. Filed by the FAA in regulations.gov docket FAA-2025-1101; AD 2025-12-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Ipeco Service Bulletin 063-25-20](https://openairdocs.org/service-documents/ipeco/sb-063-25-20.md)
- Title as filed: Ipeco Service Bulletin 063-25-20
- Pages: 15
- PDF: https://openairdocs.org/files/sha256/cc/f3/ccf32d40a2a9ae73dbf9048f6ed824a9fc8b96256e8d385c3f4695c3f9f02bd6
- Page: https://openairdocs.org/service-documents/ipeco/sb-063-25-20/file/ccf32d40a2a9

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SERVICE BULLETIN 
Issue: 1 Date: 25 March 2025 Page 1 of 15 
Form H518-1 
EQUIPMENT / FURNISHINGS 
FLIGHT COMPARTMENT 
PACKER DISTRIBUTION  
INSPECTION 
SERVICE BULLETIN NUMBER 
063-25-20 
ISSUE 1 
ISSUED BY: 
CAGE CODE: K9075 
IPECO HOLDINGS LTD 
AVIATION WAY 
SOUTHEND ON SEA 
SS2 6UN 
UNITED KINGDOM 
TELEPHONE: +44 (0)1702 545118 EMAIL: Technicalsupport@ipeco.com 
IPECO HOLDINGS LTD IS A COMPANY REGISTERED IN ENGLAND AND WALES, COMPANY NO. 00672443 
© Ipeco Holdings Ltd  2025. All rights reserved.   This is a confidential and proprietary document.   This document 
and all information contained herein is the sole property of and proprietary to Ipeco Holdings Ltd. and is supplied in 
confidence.  No intellectual property rights are granted by the delivery of this document nor by the disclosure of its 
content.  This document shall not be reproduced or disclosed to a third party nor shall it be used for any purpose 
other than that for which it is supplied without the express prior written consent of Ipeco Holdings Ltd.

### Page 2 (OCR)

peco
SERVICE BULLETIN
SERVICE BULLETIN NO.
063-25-20
COMPILED BY  R PERRIN
D. CAIRNS
CHECKED BY
TECHNICALLY APPROVED BY  ¡GARDNER
JDah  J.DCasta
COMMERCIALLY APPROVED BY
063-25-20
Issue:  1  Date: 25 March 2025  Page 2 of 15
Form H518-1

### Page 3

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 3 of 15 
Form H518-1 
1 Planning Information 
A. Effectivity 
This Service Bulletin is applicable to the Ipeco 063 Series Crew Seats  with the part 
numbers that follow: 
Ipeco Part Numbers (Pilot Seat) Ipeco Part Numbers (Co-Pilot Seat) 
3A063-0033-(  )-( ) 
3A063-0035-(  )-( ) 
3A063-0037-(  )-( ) 
3A063-0079-(  )-( ) 
3A063-0099-(  )-( ) 
3A063-0034-(  )-( ) 
3A063-0036-(  )-( ) 
3A063-0038-(  )-( ) 
3A063-0080-(  )-( ) 
3A063-0100-(  )-( ) 
B. Concurrent Requirements 
SB063-25-15, SB063-25-16, SB063-25-17, SB063-25-18. 
C. Reason 
There has been reports that after implementation of SB063-25-15, SB063-25-16, 
SB063-25-17 or SB063-25-18, as applicable, unwanted movement of the crew seat 
has occurred. The cause has been found to be that, if the number, type and 
position of the fore/aft tube packers is not equal, the seat does not always lock 
correctly. 
This condition, if not corrected, can cause more examples of unwanted movement 
of the crew seat, and possible decreased control of the aircraft. 
D. Description 
This Service Bulletin gives a full inspection procedure to make sure that: 
 
- The number, type and position of the fore/aft tube packers is correct 
- The direction of the fore/aft control lever is correct 
- The seat locks in all track lock positions.  
 
This Service Bulletin also gives instruction to correct the number, type and position 
of the fore/aft tube packers if necessary. 
E. Compliance Recommendation 
Mandatory

### Page 4

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 4 of 15 
Form H518-1 
F. CAA Approval 
This Service Bulletin has been reviewed and approved by Ipeco. This modification 
does not revise the approved configuration under: 
 
- CAA approval E12862 for the seat variant 3A063-0033/34. 
 
- EASA Approval EASA.21O.10067247 REV.A for the seat variant 3A063-
0035/36/37/38. 
 
- CAA approval E13323 for the seat variant 3A063-0079/80. 
 
- EASA approval EASA.210.10067247 REV.A for the seat variant 3A063-0099/0100 
and has been done under Ipeco ADOA approval UK.AP0126. 
For installation on ATR aircraft, the technical content of this document is approved 
under the Authority of the DOA ref.EASA.21J.044. 
G. Manpower 
The procedures in this Service Bulletin will take approximately 1 hour for each seat. 
Note: This does not include: 
- Time to schedule the work 
- Time to examine the work 
- Time to find the tools. 
- Time to remove seat from aircraft. 
 
H. Weight and Balance 
Not applicable 
I. Electrical Load Data 
Not applicable 
J. Software Accomplishment Summary 
Not applicable 
K. References 
Ipeco Component Manuals: 
 
SM634 (CMM 25-11-21) 
SM635 (CMM 25-11-22) 
SM661 (CMM 25-11-46) 
SM706 (CMM 25-11-90)

### Page 5

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 5 of 15 
Form H518-1 
L. Publications Affected 
Ipeco Component Manuals: 
 
SM634 (CMM 25-11-21) 
SM635 (CMM 25-11-22) 
SM661 (CMM 25-11-46) 
SM706 (CMM 25-11-90) 
M. Interchangeability of Parts 
Not applicable 
N. Warranty Statement 
           The procedures of this Service Bulletin are not included in Ipeco warranty.

### Page 6

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 6 of 15 
Form H518-1 
2 Material Information 
A. Material Cost and Availability 
Required per seat: 
 
Part Number Description Thickness (Inches) Quantity 
3A063-0281 STOP  0.031 4 
3A063-0509 PACKER  0.020 A/R 
For information about cost, lead time and availability of parts, operators can contact 
their nearest Ipeco Service Centre. Please include the information that follows with 
all chargeable orders: 
- Title and Part Number 
- Quantity Required 
- Name of Airline/Operator 
- Part Number of Equipment 
- Serial Number of Equipment 
Operators not included in the regions below can send an order to: 
 
Ipeco Holdings Limited 
Sales Department 
Aviation Way 
Southend-on-Sea 
SS2 6UN 
United Kingdom 
Telephone: +44 (0)1702 549371 
E-mail: sales@ipeco.com

### Page 7

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 7 of 15 
Form H518-1 
Operators in the Americas region can send an order to: 
Ipeco Inc 
2275 Jefferson Street 
Torrance 
California 90501 
USA 
Telephone: +1 310-783-4700 
E-mail: sales@ipecoinc.com 
Operators in the Greater China region can send an order to: 
Ipeco Service Centre Hong Kong Ltd. 
21st Floor 
Nan Dao Commercial Building 
359-361 Queen’s Road Central 
Hong Kong 
China 
Telephone: +852 2543 8039 
E-mail: sales@ipeco.com.hk 
Operators in the South East Asia, Oceania and Japan Region can send an order to: 
Ipeco Singapore Pte Ltd 
690 West Camp Road 
JTC Aviation Two #08-01/02/03 
Singapore 797523 
Telephone: +65 6932 1555 
E-mail: sales@ipeco.com.sg

### Page 8

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 8 of 15 
Form H518-1 
B. Industry Support Information 
For the applicable warranty statement refer to section 1.N. Warranty  
Statement. 
For pricing of the components necessary to do this Service Bulletin, refer to 
section 2.A. Material Cost and Availability. 
C. Material Necessary for Each Component 
Table 1 –Packer Reference 
 Part Number Description Thickness (Inches) Quantity 
1 3A063-0281 STOP  0.031 4 
2 3A063-0509 PACKER  0.020 A/R* 
           Note: * As Required to meet requirements of Section 3, Part B. 
D. Material Necessary for Each Spare 
As Required / if needed 
E. Re-identified Parts / Existing Parts Accountability 
Not applicable 
F. Special Tooling – Price and Availability 
Not applicable 
G. Special Tooling Necessary to do this Service Bulletin 
Not applicable

### Page 9

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 9 of 15 
Form H518-1 
3 Accomplishment Instructions 
Note 1: To do the inspection, and possible correction procedures, in this Service 
Bulletin, the seat must be removed from the aircraft  in accordance with 
applicable Aircraft Maintenance Manual (AMM). 
Note 2: W hen you do the procedures i n this Service Bulletin , keep all removed 
items unless the instructions tell you to discard them. 
Note 3: I tem number shown thus: - (*) refer to items shown in Table 1 of section 
2.C. Material Necessary for Each Component. For example, ( 1) refers to 
item 1.

### Page 10

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 10 of 15 
Form H518-1 
Part A: Inspection of the Packers Installed on the Fore/Aft Tubes  
 
1. Before you inspect the seat, remove it from the aircraft , in accordance with the 
applicable AMM. In the workshop, turn the seat head down so that you have a 
satisfactory view of the bottom of the seat and the fore/aft tubes.  
2. Inspect the two fore/aft tubes for the number , type and position of the Stops (1) 
and the Packers (2). Refer to the instruction below and Figure 1. 
a. Check four Stop s (1) 0.031 inch thick, are  fitted one in each corner, next  to 
the outer side of the bearing housing.  
b. Check Packers (2) 0.020 inch thick, are fitted following the instruction below, 
an example is shown in Figure 1, to remove longitudinal movement.  
Notes:  
- The number of Packers (2) can be different for the fwd and aft positions to remove 
longitudinal movement. 
- The number of Packers (2) in the fwd position must be equal in number  and 
position on the two fore/aft tubes.  
- The number of Packers (2) in the aft position must be equal in number and 
position on the two fore/aft tubes. 
 
3. Put the seat in the full aft position and check the pin is properly engaged in the 
track lock without longitudinal movement.

### Page 11

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 11 of 15 
Form H518-1 
4. Put the seat in the full forward position and check the pin is properly engaged in 
the track lock without longitudinal movement. 
 
5. If the Stops (1) and the Packers (2) are not equal in number, type and/or position 
or there is longitudinal movement, c ontinue to Part B .  If the Stops (1) and the 
Packers (2) are equal in number, type and position and there is no longitudinal 
movement go to Part C.

### Page 12

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 12 of 15 
Form H518-1 
Part B: Removal and Installation of Packers and Stops. 
 
1. If not already done so, make sure that the seat is removed from the aircraft , in 
accordance with the applicable AMM. In the workshop, turn the seat head down 
so that you have a satisfactory view of the bottom of the seat and the fore/aft 
tubes. 
Note: 
- It is not necessary to disassemble the seat structure to do the procedures in this 
Service Bulletin. You can get access to the stops (1) and packers (2) from the bottom 
of the seat.  
 
2. R emove and keep the four Stops (1) and all Packers (2) from the fore/aft tubes. 
To remove the Stops (1) and Packers (2) from the f ore/aft tubes, open the 
installation slot, part of the Stops (1) and Packers (2), then remove the Stops (1) 
and Packers (2) from the fore/aft tubes.  
Note: 
- The Stops (1) and Packers (2) are made from Nylon 6 or 66. You can easily open 
them with no risk of damage. 
 
3. Install the Stops (1) one in each corner, adjacent to the outer side of the bearing 
housing, as shown in Figure 1. Do this before you install the packers (2).  
To install the Stops (1) onto the f ore/aft tubes, open the installation slot, part of 
the Stops (1), then install the Stops (1) onto the fore/aft tubes.  
Note: 
- The direction of the installation slot of the Stops (1) and Packer (2) after assembly  
is not important. 
 
4. Refer to the instruction below and Figure 1 to install the Packers (2) to ensure 
that the pins engage properly in the track lock. 
To install the Packers (2) onto the fore tubes, put the seat in the full aft position 
and add packers (2) until the pin is properly engaged in the track lock without 
longitudinal movement.  
 
To install the Packers (2), open the installation slot, part of the Packers (2), then 
install the Packers (2) onto the fore tubes.

### Page 13

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 13 of 15 
Form H518-1 
To install the Packers (2) onto the aft tubes, put the seat in the full forward position 
and add packers (2) until the pin is properly engaged in the track lock without 
longitudinal movement.  
 
To install the Packers (2), open the installation slot, part of the Packers (2), then 
install the Packers (2) onto the aft tubes. 
 
 
Notes:  
- The number of Packers (2)  can be different for the fwd and aft directions to 
remove longitudinal movement. 
- The number of Packers (2) in the fwd position must be equal in number and 
position on the two fore/aft tubes.  
- The number of Packers (2) in the aft position must equal in number and position 
on the two fore/aft tubes.

### Page 14

SERVICE BULLETIN 
  063-25-20 
   
Issue:  1 Date: 25 March 2025 Page 14 of 15 
Form H518-1 
Part C: Longitudinal Movement and Track Lock Pin Operation 
 
Note:  After the seat is installed in the aircraft again, in accordance with the applicable 
AMM, do the visual and physical tests that follow:  
1. Do a visual check to make sure that the track lock pin fully engages and locks 
into each track lock position through the full range of seats travel. Ref to Figure 
2. 
2. Do a visual check to make sure that the control lever goes back to its locked 
position. Make sure that the hatched area of the placard is fully out of view 
under the lever. Refer to Figure 2. 
3. Before the seat goes back into service, refer to the applicable seat CMM to: 
 
(a) Make sure that the seat engages fully in each lateral track lock position. 
(b) Do a check of the seat's vertical and recline operation.

### Page 15 (OCR)

\peco
SERVICE BULLETIN
Part D: Test & Equipment Marking
1. Use vibro-etch, or a similar method, to add the Service Bulletin number and
issue number to the Modification box on the seat identification label
(nameplate). The nameplate is on the base structure assembly. Refer to
Figure 3.
FIGURE 3
MADE IN
GT. BRITAIN
A Division of Ipeco Holdings Ltd
SEAT  PILOT SEAT
CUSTOMER PART N°
IPECO PART N°  ISSUE  SERIAL N°  INSPECTION
MODIFICATION  DATE  *
SB 063-25-20 Issue *
TSO H° C39a  DATE NFG.
MODEL N°
063-25-20
Issue:  1  Date: 25 March 2025  Page 15 of 15
Form H518-1

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
