# Agusta Alert Bollettino Tecnico 109EP-1: Revision B

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-0194; AD 2021-07-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Agusta Alert Bollettino Tecnico 109EP-1](https://openairdocs.org/service-documents/leonardo/109ep-1.md)
- Title as filed: Agusta ABT 109EP-1 Rev B
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/41/c6/41c6d3a65d5e9d375759f01ea47fab0489224496caef12430d1a59fdf20bfb04
- Page: https://openairdocs.org/service-documents/leonardo/109ep-1/file/41c6d3a65d5e

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

ALERT
AGUSTA  21017 Cascina Costa di Samarate (VA) Italy
Via GiovanniAgusta, 520
A FINMECCANICA COMPANY  Tel.: +390331 229111 - Fax: +390331 229605-222595
TRANSLATION OF
BOLLETTINO TECNICO  N° 109EP-1
Technical content of this Bollettino Tecnico is E.N.A.C. - R.A.I. approved
The E.N.A.C. - R.A.I. states mandatory compliance with inspections, modifications  DATE July 21, 1998
or technical directives and related time of compliance by means of
relevant Prescrizioni di Aeronavigabilita.  REV. B December 19, 2000
this bulletin is:  Compliance with  MANDATORY
MODELS AFFECTED: A109E.
SUBJECT:  INSPECTION OF THE TIP CAP OF MAIN ROTOR BLADES P/N 709-0103-
01 (ALL DASH NUMBERS).
REASON:  To inspect tip cap of subject blades for presence of debonds and/or cracks.
HELICOPTERS AFFECTED:
All main rotor blades P/N 709-0103-01 up to S/N 1428 included, preceded by
code A5 or EM, installed on Agusta A109E helicopters or stocked parts.
NOTE
The main rotor blades P/N 709-0103-01
that have replaced the tip cap and have
installed the new tip cap P/N 709-0103-
29-109 do not require compliance with
this Bollettino. The P/N 709-0103-29-
109 is marked on upperside of tip cap
(in the area indicated in Figure 1).
COMPLIANCE:
Within and not later than ten (10) operating hours from the receipt of this
Bollettino and subsequently every twenty-five (25) operating hours.
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership  of aircraft has changed, please, forward to new owner.
ALERT  Page 1 016 | E

### Page 2 (OCR)

B.T. 109EP-1.
DESCRIPTION:
Cases of openings on tip cap leading edge of blades P/N 709-0103-01 have
occurred, with subsequent increase of helicopter vibratory level. The
investigation has evidenced the presence of extense areas of debond of the
honeycomb core, causing a "pulsated" effect on tip cap, leading to cracks on
leading edge (joint line of shells) of tip cap.
This Bollettino is issued with the purpose of providing an inspection (upper
and lower sides) using a hammer for presence of voids:
B  • between metal shells and honeycomb core of the tip cap;
• tip cap and blade joint area.
In addition this Bollettino prescribes a liquid penetrant inspection to determine
for possible presence of cracks or leading edge (welded joint line of the tip
cap shells).
REQUIRED MANPOWER:
One and-a-half (1.5) estimated manpower hours are required for each main
rotor blade for compliance with this Bollettino.
WARRANTY: If during the accomplishment of this Bollettino the tip cap is found outside the
allowable limits please inform Agusta.
REQUIRED MATERIALS:
The following consumable materials are required to accomplish this Bollettino:
abrasive paper grit N° 320 or more fine
solvent (exane, or petroleum ether, or aliphatic naphtha according to
TT-N-95 type 2) or solvent 9PR5 available from BRENT International;
B  visible dye penetrant P6R available from BRENT International;
nonaqueous wet developer 9D1B spray available from BRENT
International;
one or more white light sources able to provide an illuminance of at
least 1000 lux on inspection area.
Page 2 of 6

### Page 3 (OCR)

B.T. 109EP-1
Alternative products to the solvents, penetrant and developer specified above
are permitted provided that:
they comply to the requirements of AMS2644 (class 2 for the solvent,
type 2 and method "c" for the penetrant and form "e" for the developer);
they are listed in the pertinent QPL-AMS-2644-1;
the penetrant and developer are produced by the same company.
SPECIAL TOOLS: N.A.
WEIGHT AND BALANCE CHANGES: N.A.
REFERENCES:
Pertinent Maintenance Manual.
PUBLICATIONS AFFECTED:
Pertinent Maintenance Manual.
COMPLIANCE INSTRUCTIONS:
NOTE
The procedure reported below is
applicable to each one of the four main
rotor blades, if affected by this
Bollettino.
1.  Using the steel hammer P/N 109-3101-58-1 and in accordance with the pertinent
Maintenance Manual, perform a detailed inspection of the blade tip cap (upper
and lower sides) for presence of voids:
• between metal shells and honeycomb core (refer to figure 1);
• tip cap to blade bondage area (in this area no debond voids are permitted).
Page 3 of 6 | B

### Page 4 (OCR)

B.T. 109EP-1
CAUTION
tapping inspection with the
hammer must be carried out by skilled
personnel, able to identify defects if
present on the bonded components. If
skilled personnel is not available please
contact Agusta.
Visually inspect the tip cap (upperside and lowerside) for swellings and/or
deformations.
Using the visible dye penetrant method, inspect the tip cap leading edge along the
welded joint line of the shells for presence of cracks as follows (refer to figure 1):
NOTE 1
The following  inspection does not
require blade removal from helicopter.
NOTE 2
The  following  operation must be
accomplished at the first application of
the liquid penetrant inspection.
3.1.  Using abrasive paper grit n° 320 or more fine, remove the paint from area B, on
both upper and lower sides, inboard 5 to 10 mm from leading edge and starting at
30 mm from the trailing edge. Mask surrounding painted areas using adhesive
tape.
B
3.2.  Perform liquid penetrant inspection as follows:
CAUTION
Personnel  conducting the liquid
penetrant inspection must be qualified
in accordance with the ASNT practice
SNT-TC-1A or other equivalent practice
standard. The blade, the penetrant and
ambient temperatures shall be between
4 and 45°C.
3.2.1.  Thoroughly degrease inspection area using a cloth soaked in solvent (refer to
paragraph REQUIRED MATERIALS).
Leave solvent to completely evaporate.
3.2.2.  Using adhesive tape mask trailing edge inboard for approximately 30mm to avoid
possible penetrant infiltration in the tip cap.
Page 4 of 6

### Page 5 (OCR)

B.T. 109ЕP-1
3.2.3.  Apply the penetrant in the inspection area extending approximately 5mm inboard
from trailing edge (refer to view A of figure 1), on both upper and lower sides.
Penetrant dwell time shall be 30 to 40 minutes.
3.2.4.  Remove excess penetrant with a clear dry cloth followed by a cloth dampened in
solvent until the background color has been completely removed.
NOTE
Do not directly pour the solvent on the
inspection area.
3.2.5. Apply a thin and uniform layer of developer 9D1B, after 10 to 15 minutes illuminate
area to 1000 lux and examine it presence of cracks.
3.2.6.  Upon completion of inspection, clean affected area with a clean dry cloth followed
by a cloth dampened in solvent.
4.  The blade that show debonds voids which exceed the prescribed limits of the
pertinent Maintenance Manual and/or swellings, deformations and/or cracks, must
be removed from service.
In this case, please inform immediately Agusta.
NOTE
The inspections required with this
Bollettino are not applicable if tip cap
replacement with new cap P/N 709-
0103-29-109.
The replacement is carried out by
Agusta or authorized Service Station.
5.  Return the helicopter in ready to flight condition.
Page 5 of 6 1 B

### Page 6 (OCR)

B.T. 109EP-1
TIP CAP
1P/N 709-0103-29-109
LAP PLATE  MARKING
163.0  INSPECTION AREA OI
THE LEADING EDGE
115.0
VIEW A
AREA
187.0  HONEY COMB
CORE
29.5
B
27.0  221.0
273.0
INSPECTION AREA ON
PAINTED AREA
THE LEADING EDGE
DIMENSIONS IN MILLIMETERS
VIEW A
~5
FIGURE 1
Page 6 of 6

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
