# Leonardo Emergency Alert Service Bulletin 109EP-157: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2017-0940; AD 2018-07-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Emergency Alert Service Bulletin 109EP-157](https://openairdocs.org/service-documents/leonardo/109ep-157.md)
- Title as filed: Leonardo Helicopters SB Emergency Alert 109-EP157
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/a5/a5/a5a529c838e88dc0ebbde66265454d4af7c05f1aaf613c7e48a33b97ac97598e
- Page: https://openairdocs.org/service-documents/leonardo/109ep-157/file/a5a529c838e8

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N°  109EP-157
DA TE:  September 8, 2017 
REV. : /-March 3, 2017 
Pa ge 1 of 10 
TITLE 
ATA 62 – MAIN ROTOR BLADE TIP CAP, INSPECTION OF 
REVISION LOG 
New Issue 
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
EMERGENCY ALERT
SERVICE BULLETIN

### Page 2

S.B. N°109EP-157 EMERGENCY ALERT 
 DATE: September 8, 2017 
Page 2 of 10 REVISION: / 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
All the A109EP equipped with main rotor blade P/N 709-0103-01-111 S/N 681 and  
S/N 683 which has accumulated less than 400FH (Time Since New). 
NOTE 
If any of the above Main Rotor Blade is in stock, please 
contact aw109.mbx.aw@leonardocompany.com to 
obtain information on how to handle the parts. 
B. COMPLIANCE 
Within and not later than 25 (twenty-five) flight hours since the date of issuance of this 
Service Bulletin and subsequently each 25 (twenty-five) flight hours. 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin is issued in order to provide the necessary instruction to perform 
a repetitive inspection of the tip cap installed on a defined batch of main rotor blades 
P/N 709-0103-01-111 to detect potential debonding. 
E. DESCRIPTION 
A case of debonding of the tip cap from the main rotor blade has been reported on an 
AW109SP helicopter, this resulting in the loss of the tip cap in flight. This event did not 
compromise the conduct of flight. 
The investigation has individuated as cause of the occurrence the incorrect bonding 
procedures during the manufacturing of some main rotor blades. 
Leonardo Helicopters, as precautionary measure, issued this Service Bulletin to 
perform a tapping test in order to detect potential debonding and to perform the 
replacement of the main rotor blade. 
F. APPROVAL 
The content of this Service Bulletin is approved under the authority of DOA nr. 
EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal.

### Page 3

S.B. N°109EP-157 EMERGENCY ALERT 
DATE: September 8, 2017 
REVISION: / Page 3 of 10 
E.A.S.A. states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If a helicopter listed in the effectivity embodies a modification or repair not LHD 
certified and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin the following Maintenance-Man-Hours are 
deemed necessary: 
approximately one (1) MMH. 
Maintenance-Man-Hours are based on hands-on time and can change with personnel 
and facilities available. 
H. WEIGHT AND BALANCE 
N.A.  
 
 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE / SECTION DESCRIPTION 
DM01 00-20-1 Helicopter safety 
DM02 62-11-17 Damage on tip cap 
DM03 62-11-6 Main rotor blade Removal/installation 
2) ACRONYMS 
DOA Design Organization Approval 
DM Data Module 
EASA European Aviation Safety Agency 
LHD Leonardo Helicopter Division 
MMIR Maintenance Malfunction Information Report 
N.A. Not Applicable 
P/N Part Number 
SB Service Bulletin

### Page 4

S.B. N°109EP-157 EMERGENCY ALERT 
 DATE: September 8, 2017 
Page 4 of 10 REVISION: / 
S/N Serial Number 
3) ANNEX 
Annex A Hammer Tapping Inspection AW109 Tip-Cap. 
J. PUBLICATIONS AFFECTED 
N.A. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 5

S.B. N°109EP-157 EMERGENCY ALERT 
DATE: September 8, 2017 
REVISION: / Page 5 of 10 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
P/N DESCRIPTION Q.TY NOTE 
709-0103-01-111 Main rotor blade AR  
2) CONSUMABLES 
N.A.     
B. SPECIAL TOOLS 
P/N DESCRIPTION Q.TY NOTE PART 
109-3101-58-1 or 
equivalent 
Tapping hammer (steel head) 1   
     
C. INDUSTRY SUPPORT INFORMATION 
WARRANTY: Owners/Operators who comply with the instructions of this Service 
Bulletin no later than the applicable date in the “Compliance” section will be eligible to 
receive REQUIRED MATERIALS on free of charge basis, except for Consumable 
Materials and Special Tools.  
NOTE: Customers who fail to comply with the instructions in this Service Bulletin 
before the compliance date are not eligible for the aforementioned special policy.  
Please Issue relevant MMIR form to your Warranty Administration Dpt.  
NOTE: WRM will include RETURN MATERIAL AUTHORIZATION (RMA) number; the 
unit disembarked (P/N 709-0103-01-111 Main Rotor Blade) from the aircraft has to be 
returned to LHD within thirty (30) calendar days after the shipment of the replacement 
part. In case of missing return within thirty (30) calendar days, Customer will be 
invoiced for the price of the replacement part.  
NOTE: The S/N and INSPECTION REPORT are mandatory; in case the MMIR is not 
accompanied by these documents, it will be rejected.

### Page 6

S.B. N°109EP-157 EMERGENCY ALERT 
 DATE: September 8, 2017 
Page 6 of 10 REVISION: / 
3. ACCOMPLISHMENT INSTRUCTIONS 
1. In accordance with Maintenance Manual Section 00-20-1, prepare the helicopter on 
ground for a safe maintenance. 
2. Gain access to the main rotor blades P/N 709-0103-01-111. 
NOTE 
The authorized personnel who will carry out the test 
must comply with the requirements listed in Annex A. 
3. Perform a tapping test in accordance with Annex A  on the Main Rotor Blade area 
identified in Figure 1. 
4. In case no debonding is found, proceed with step 6. 
5. In case debonding is found, check its dimensions with Maintenance Manual Section  
62-11-17 (debonding limits). 
5.1 In case debonding is found within acceptable limits proceed with step 6. 
5.2 In case debonding is found outside the acceptable limits, before next flight 
remove the Main Rotor Blade affected in accordance with Maintenance Manual  
procedures and contact Leonardo Helicopters Spa Customer Support at the 
following mail box: 
aw109.mbx.aw@leonardocompany.com 
6. Return the helicopter to a ready to flight configuration and record for compliance with this 
Service Bulletin on the Main Rotor Blade log card. 
7. Send the attached compliance form to the following mail box: 
 aw109.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 7 (OCR)

: LEONARDO
HELICOPTERS
STA  STA  STA
5200  5280  5630
25 mm
TIP CAP
EROSION SHIELD
115 mm
TOP SURFACE
TIF CAP
80 mm
Tapping hammer area  TRAILING EDGE
BOTTOM SURFACE
TIP CAP
EROSION SHIELD
AREA A (Between Tip Cap and Blade body)
AREA B (Between Tip Cap and Blade body)
Tapping area of both upper and lower sides
Figure 1
S.B. N°109EP-157 EMERGENCY ALERT
DATE: September 8, 2017
REVISION: /  Page 7 of 10

### Page 8

S.B. N°109EP-157 EMERGENCY ALERT 
 DATE: September 8, 2017 
Page 8 of 10 REVISION: / 
ANNEX A 
HAMMER TAPPING INSPECTION AW109 TIP-CAP

### Page 9

ANNEX A 
S.B. N°109EP-157 EMERGENCY ALERT 
DATE: September 8, 2017 
REVISION: / Page 9 of 10 
 
SPECIFIC REQUIREMENTS OF INSPECTION 
Carry out hammer tapping inspection with hammer P/N 109-3101-58-1 of both upper 
and lower sides and nose of the blade to detect potential debonding. Report results. 
 
GENERAL REQUIREMENTS 
1. PERSONNEL AUTHORIZATION REQUIREMENTS 
In order to be authorized to carry out hammer tapping inspections, the assigned 
personnel shall: 
1.1 have passed the near vision examination and colour perception requirements 
specified in EN4179 / NAS410; 
1.2 have passed an audiometric test which  consists of a test at 500, 1000, 2000 and 
3000 Hz frequencies with the following acceptance criteria: 
a. average maximum loss of 30 dB at the four frequencies, 
b. maximum loss of 50 dB at every single frequency. 
NOTE 
The above requirements shall be considered as a minimum; other 
tests and requirements based on local national health and safety 
protection rules are acceptable on condition that the above 
requirements are satisfied or exceeded. 
1.3 have a minimum of 40 hours of documented practical experience obtained under the 
direct supervision of personnel having previous authorization in hammer tapping 
inspection; 
1.4 have knowledge of the type of structure to be tested in order to be aware of the 
change of sound due to the configuration/lay-up of the part, such as, but not limited 
to: 
 Different thickness of the top layers, 
 Overlap areas, 
 Inserts, 
 Changes to the geometrical form of the part, 
 Edge effects, 
 Changes to the distance between supports and fasteners, 
 Changes to the thickness of adhesive, 
 Areas with sealant, 
 Changes to the type of honeycomb, 
 Areas with core filler or splice adhesive.

### Page 10

ANNEX A 
 S.B. N°109EP-157 EMERGENCY ALERT 
 DATE: September 8, 2017 
Page 10 of 10 REVISION: / 
1.5 be aware of the change of sound on a specific structure when it is defective and 
when it is intact. 
2. MAINTENANCE OF AUTHORIZATION 
In order to maintain the authorization to carry out hammer tapping inspections, the 
assigned personnel shall repeat with annual frequency the tests reported at items no.1.1 
and no. 1.2 in paragraph no.1. 
 
3. HAMMER TAPPING 
The hammer shall comply with the requirements of part number 109-3101-58-1 with the 
tapping head made of steel. 
 
4. PROCEDURE 
This type of inspection is conducted by impacting the component and performing a 
subjective evaluation of the emitted sound. 
Tapping shall be performed from a height of 25 mm to 40 mm from the surface without 
causing dents on the area being inspected, by moving smoothly along the direction of 
test and complying with the grid of 3 mm maximum. 
Tap on bends and edges with the conical side (#1 in Fig. A) of the Tap hammer, while 
Tap on the flat areas with the rounded side of the Tap hammer (#2 in Fig. A). 
Tapping shall be performed with the minimum energy necessary to generate a clear and 
audible sound and repeatable with the same intensity. 
The inspection shall be performed in a quiet environment. The maximum level of noise 
(sum of the environmental noise with the noise due to the tapping inspection) should not 
exceed 80dB, as stated by the health protection rules. The noise level due to the tapping 
inspection shall be at least 5dB higher than the environmental noise without the tapping. 
 
 
Figure A – Sketch of the Tapping hammer.

### Page 11

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
