# Leonardo Alert Service Bulletin 109EP-173: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2025-2556, the docket of AD 2026-09-09. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 109EP-173](https://openairdocs.org/service-documents/leonardo/109ep-173.md)
- Title as filed: Leonardo Helicopters ASB 109EP-173 Rev B
- Pages: 110
- PDF: https://openairdocs.org/files/sha256/40/dc/40dc918516e4d1406ebaa12da87063e5a8340b3a8c7f8507518bdce3e6a13c6d
- Page: https://openairdocs.org/service-documents/leonardo/109ep-173/file/40dc918516e4

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ERRATA CORRIGE 
 
 
Please find here attached the pages that have to be replaced in the basic Service Bulletin 
n°109EP-173 Rev. B.  
 
 PAGE 25 “ACCOMPLISHMENT INSTRUCTIONS Step 65” 
 
Was: 
 
• Move the collective stick three or four times. Ma ke sure that the collective controls are free 
to operate without friction against the structure. 
 
Becomes: 
 
• Move the collective stick three or four times. Ma ke sure that the collective controls are free 
to operate without friction against the structure. 
• In accordance with MM Paragraph 67-11-16, adjust fixed friction. 
 
 
 PAGE 47 “ACCOMPLISHMENT INSTRUCTIONS Step 72” 
 
Was: 
 
• Move the collective stick three or four times. Ma ke sure that the collective controls are free 
to operate without friction against the structure. 
 
Becomes: 
 
• Move the collective stick three or four times. Ma ke sure that the collective controls are free 
to operate without friction against the structure. 
• In accordance with MM Paragraph 67-11-16, adjust fixed friction.

### Page 2

N ° 109EP-173 
D ATE:  November 10, 2020 
REV. :  B  - August 24, 2023 
P age 1 of 108 
TITLE 
ATA 53 - CENTRAL FUSELAGE FRAME ASSY AT STA 1815, INSPECTION, REPAIR 
AND REINFORCEMENT OF 
REVISION LOG 
Revision B is issued in order to introduce the following changes: 
- Amend minor errors; 
- Introduce Part IV and Part V. 
Revision bars identify changes. 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 3

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 2 of 108 REVISION: B - August 24, 2023 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
All the A109E helicopters from S/N 11001 thru S/N 11674 included. 
B. COMPLIANCE 
NOTE 
The helicopter’s posts that have been repaired in 
accordance with Part II (LH side) or Part III (RH side) of 
this Service Bulletin, or in accordance with repair 
drawing P/N 109-0952-67-117 (LH side) or P/N  
109-0952-67-102 (RH side), shall be inspected in 
accordance with Part I after they have accumulated 
more than 1000 FH of 3500 landings since repair. 
NOTE 
The helicopter’s posts that have been reinforced in 
accordance with Part IV (LH side) or Part V (RH side) of 
this Service Bulletin are no longer affected by the 
relevant inspection (ref. Part I). 
Helicopter that have accumulated more than 1000FH or  3500 landings, whichever 
occurs first: 
 PART I: 
Within and not later than 100FH from the issuance of this SB and every 100FH 
thereafter. 
 PART II AND PART III: 
- Within and not later than the next 25FH if the length of crack on the FWD 
CAP does not exceed 50 mm and no other damages are detected in the 
affected area.

### Page 4

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 3 of 108 
NOTE 
If the length of the cracks exceeds the boundaries of the 
FWD CAP, INNER FORWARD ANGLE or WEB (ref. 
Figure 1), the repair scheme reported in Part II and III of 
this Service Bulletin could not be applicable. In this case 
contact Leonardo Engineering Dept 
engineering.support.lhd@leonardo.com before the next 
flight. 
- Before the next flight if the length of crack on t he FWD CAP is greater than 
50 mm and/or any other crack(s) are detected. 
 PART IV AND PART V: 
Within and not later than August 31, 2026. 
 
Helicopter that have accumulated up to 1000FH or 3500 landings, whichever occurs 
first: 
 PART I: 
Within and not later 100FH upon the achievement of 1000FH or 3500 landings 
and every 100FH thereafter. 
 PART II AND PART III: 
- Within and not later than the next 25FH if the length of crack on the FWD 
CAP does not exceed 50 mm and no other damages are detected in the 
affected area. 
NOTE 
If the length of the cracks exceeds the boundaries of the 
FWD CAP, INNER FORWARD ANGLE or WEB (ref. 
Figure 1), the repair scheme reported in Part II and III of 
this Service Bulletin could not be applicable. In this case 
contact Leonardo Engineering Dept 
engineering.support.lhd@leonardo.com before the next 
flight. 
- Before the next flight if the length of crack on t he FWD CAP is greater than 
50 mm and/or any other crack(s) are detected. 
 PART IV AND PART V: 
Within and not later than August 31, 2026.

### Page 5

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 4 of 108 REVISION: B - August 24, 2023 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin is issued in order to provide the necessary instruction on how to 
perform an inspection to detect cracks in the center fuselage at intersection of lateral 
pylon (LH and RH side) with floor spar, and, in case of findings, to repair it. Moreover, 
the instructions for corrective actions (reinforcements) are provided. 
E. DESCRIPTION 
Some occurrences of cracks have been found in the fuselage of the Leonardo S.p.a. 
A109E helicopters at the intersection of the lateral pylon with the floor spar at the STA 
1815, either in the LH and RH side.  
In Part I of this Service Bulletin are given the instruction to perform an inspection in the 
area affected by the possible cracks, in Part II are given the instruction for LH side 
fuselage repair and in Part III are given the instruction for RH side fuselage repair.  
Revision B is issued to provide the instruction for LH side fuselage reinforcement (Part 
IV) and for RH side fuselage reinforcement (Part V). 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA nr. 
EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
with Local Aviation Authority. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin the following MMH are deemed necessary: 
Part I: approximately 6 (six) hours; 
Part II: approximately 120 (one hundred and twenty) hours; 
Part III: approximately 120 (one hundred and twenty) hours.

### Page 6

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 5 of 108 
Part IV: approximately 120 (one hundred and twenty) hours; 
Part V: approximately 120 (one hundred and twenty) hours. 
MMH are based on hands-on time and can change with personnel and facilities 
available. 
H. WEIGHT AND BALANCE 
PART I, II and III: 
N.A. 
PART IV 
WEIGHT (kg) 0.91 
 ARM (mm) MOMENT (kgmm) 
LONGITUDINAL BALANCE 1880 1710 
PART V 
Negligible.

### Page 7

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 6 of 108 REVISION: B - August 24, 2023 
I. REFERENCES 
I.1 PUBLICATIONS  
DATA MODULE DESCRIPTION PART 
DM01 00-20-1 Helicopter safety All 
DM02 06-40-1 Access panels and doors II, III, IV, V 
DM03 00-10-4 Connection/disconnection of external 
electrical power 
II, III, IV, V 
DM04 00-10-8 Connection/disconnection of external 
hydraulic power 
II, III, IV, V 
DM05 25-11-9 Crew seats - removal/installation II, III, IV, V  
DM06 25-21-12 Forward seat - removal/installation II, III, IV, V  
DM07 21-21-1 Air distribution system II, III, IV, V 
DM08 52-11-9 LH/RH cockpit doors - 
removal/installation 
II, III, IV, V 
DM09 67-11-1 Collective pitch control system II, IV 
DM10 67-11-9 Collective pitch control lever - 
removal/installation 
II, IV 
DM11 25-81-7 Cockpit soundproofing panels - 
removal/installation 
All 
DM12 25-81-9 Passenger soundproofing panels - 
removal/installation 
All 
DM13 52-71-6 Operational test of cockpit/passenger 
compartment caution system 
II, III, IV, V 
DM14 67-12-1 Cyclic pitch control system III, V 
DM15 67-00-12 Control tube - general maintenance  II, III, IV, V  
DM16 07-30-1 Hoisting of complete helicopter II, III, IV, V  
DM17 07-30-2 Hoisting of helicopter without main 
rotor 
II, III, IV, V 
DM18 67-00-25 Collective pitch control adjustment II, IV 
DM19 67-00-26 Cyclic pitch control adjustment III, V 
DM20 67-11-16 Fixed friction adjustment II; IV 
I.2 ACRONYMS 
AR As Required 
DOA Design Organization Approval 
EASA European Aviation Safety Agency 
LHD Leonardo Helicopters Division 
LS Local Supply 
DM Data Module 
FH Flight Hours

### Page 8

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 7 of 108 
MMH Maintenance Man Hours 
N.A. Not Applicable 
P/N Part Number 
SB Service Bulletin 
S/N Serial Number 
I.3 ANNEX 
N.A. 
J. PUBLICATIONS AFFECTED 
A109E-MM Maintenance Manual A109E Helicopter Model. 
A109E-MPM Maintenance Planning Manual A109E Helicopter Model. 
3C-A-ASRP-00-X - AW119/A109 Series Air Vehicle Structural Repair Publication. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 9

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 8 of 108 REVISION: B - August 24, 2023 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
A.1   PARTS 
PART I 
N.A. 
PART II 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
1 109-0952-67-117  REPAIR ASSY, LH REF .  - 
2 109-0320-90-207 109-0320-90-207A1 Cap, forward LH 1 .. (1) - 
3 109-0320-90-7  Panel REF .. (1)(2) - 
4 109-0320-90-507  Cap, forward LH 1 .. (3) - 
5 109-0320-90-505  Panel REF .. (3)(4) - 
6 109-0952-67-119  Angle 1 .. (17) 709-052L1 
7 109-0952-67-121  Internal butt-strap 1 ..  709-052L1 
8 109-0952-67-123  External butt-strap 1 ..  709-052L1 
9 109-0952-67-125  Web 1 .. (18) 709-052L1 
10 109-0360-88-109  Seal assy, co-pilot door 1 .. (5) 709-052L1 
11 A233A001B AW004FE001B Fastener, seal 36 ..  709-052L1 
12 109-0360-86-109  Seal assy, LH  passenger door 1 .. (5) 709-052L1 
13 A879A05L150  Rivet, solid 5 ..  709-052L1 
14 MS27039-1-08   Screw 8 ..  709-052L1 
15 MS20426AD3-5  Rivet, solid, 100° countersunk head 0.1kg ..  709-052L1 
16 MS20426AD3-6  Rivet, solid, 100° countersunk head 0.1kg ..  709-052L1 
17 MS20426AD4-5  Rivet, solid, 100° countersunk head 0.1kg ..  709-052L1 
18 MS20426AD5-5  Rivet, solid, 100° countersunk head 0.1kg ..  709-052L1 
19 MS20426AD5-6  Rivet, solid, 100° countersunk head 0.1kg ..  709-052L1 
20 MS20426AD5-8  Rivet 0.1kg ..  709-052L1 
21 MS20426AD5-9  Rivet 0.1kg ..  709-052L1 
22 MS20470AD5-5  Rivet, solid, universal head 0.1kg ..  709-052L1 
23 MS20470AD5-6  Rivet, solid, universal head 0.1kg ..  709-052L1 
24 MS20470AD5-7  Rivet 0.1kg ..  709-052L1 
25 MS21069L08  Nut plate, self-locking 1 ..  709-052L1 
26 MS21071L08  Nut plate, self-locking 1 ..  709-052L1 
27 NAS9301B-4-02  Rivet, blind, protruding head 100 ..  709-052L1 
28 NAS9301B-4-03  Rivet, blind, protruding head 20 ..  709-052L1 
29 NAS9301B-4-04  Rivet, blind, protruding head 10 ..  709-052L1 
30 MS24665-151  Cotter Pin 2 ..  709-052L1 
31 MS24665-155  Cotter Pin 2 ..  709-052L1 
32 MS20615-4M3  Rivet, universal head 0.1kg ..  709-052L1 
33 MS20427M4-3  Rivet, 100° countersunk head 0.1kg ..  709-052L1 
34 MS20600AD4-3 MS20600AD4W3 Rivet, blind 80 ..  709-052L1 
35 NAS1720H4L4A  Rivet, blind 80 ..  709-052L1 
36 NAS1721H4L2A  Rivet, blind 30 ..  709-052L1

### Page 10

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 9 of 108 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
37 NAS1721H4L4A  Rivet, blind 20 ..  709-052L1 
        
PART III 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
38 109-0952-67-102  REPAIR ASSY, RH REF .  - 
39 109-0320-90-208 109-0320-90-208A1 Cap, forward RH 1 ..  709-052L2 
40 109-0320-90-8  Panel REF .. (6) - 
41 109-0952-67-111  Angle 1 .. (16) 709-052L2 
42 109-0952-67-113  Internal butt-strap 1 ..  709-052L2 
43 109-0952-67-115  External butt-strap 1 ..  709-052L2 
44 109-0952-67-109  Web 1 .. (15) 709-052L2 
45 109-0360-88-110  Seal assy, co-pilot door 1 ... (7) 709-052L2 
46 A233A001B AW004FE001B Fastener, seal 36 ..  709-052L2 
47 109-0360-86-110  Seal assy, LH passenger door 1 .. (7) 709-052L2 
48 A879A05L150  Rivet, solid 5 ..  709-052L2 
49 MS20426AD4-5  Rivet, solid, 100° countersunk head 0.1kg ..  709-052L2 
50 MS20470AD5-5  Rivet, solid, universal head 0.1kg ..  709-052L2 
51 MS20470AD5-6  Rivet, solid, universal head 0.1kg ..  709-052L2 
52 MS20470AD5-7  Rivet 0.1kg ..  709-052L2 
53 MS20470AD5-8  Rivet 0.1kg ..  709-052L2 
54 MS20470AD5-9  Rivet 0.1kg ...  709-052L2 
55 NAS9301B-4-02  Rivet, blind, protruding head 100 ..  709-052L2 
56 NAS9301B-4-03  Rivet, blind, protruding head 20 ..  709-052L2 
57 NAS9301B-4-04  Rivet, blind, protruding head 10 ..  709-052L2 
58 MS24665-151  Cotter Pin 4 ..  709-052L2 
59 MS20615-4M3  Rivet, universal head 0.1kg ..  709-052L2 
60 MS20615-4M4   Rivet, 100° countersunk head 0.1kg ..  709-052L2 
61 MS20600AD4-3 MS20600AD4W3 Rivet, blind 80 ..  709-052L2 
62 NAS1720H4L4A  Rivet, blind 80 ..  709-052L2 
63 NAS1721H4L2A  Rivet, blind 30 ...  709-052L2 
64 NAS1721H4L4A  Rivet, blind 20 ..  709-052L2 
        
PART IV 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
65 109G5330R01-201  LATERAL MOUNTING REINFORCEMENT REF .  - 
66 109-0320-90-207 109-0320-90-207A1 Cap, forward LH 1 .. (1)(12) 709-052L3 
67 109-0320-90-7  Panel REF .. (1)(2) - 
68 109-0320-90-507  Cap, forward LH 1 .. (3)(12) - 
69 109-0320-90-505  Panel REF .. (3)(4) - 
70 109-0952-67-123  External Butt-Strap 1 ..  709-052L3 
71 109-0952-67-125  Web 1 .. (12)(18) 709-052L3 
72 109G5307P39-113  Angle LH 1 ..  709-052L3 
73 109G5307P39-115  Left Cap 1 ..  709-052L3 
74 109G5307P39-117  Doubler 1 ..  709-052L3 
75 109G5330A25-101  Stiffener Machined LH 1 ..  709-052L3 
76 109G5330R01-205  Doubler LH 1 ..  709-052L3 
77 A879A05L150  Rivet 6 ..  709-052L3 
78 CR2245-4-2  Rivet 1 ..  709-052L3 
79 CR2245-4-5  Rivet 2 ..  709-052L3

### Page 11

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 10 of 108 REVISION: B - August 24, 2023 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
80 CR2245-5-3  Rivet 1 ..  709-052L3 
81 MS20426AD3-5  Rivet 0.1kg ..  709-052L3 
82 MS20426AD4-5  Rivet 0.1kg ..  709-052L3 
83 MS20426AD5-5  Rivet 0.1kg ..  709-052L3 
84 MS20470AD4-5  Rivet 0.1kg ..  709-052L3 
85 MS20470AD5-5  Rivet 0.1kg ..  709-052L3 
86 MS21071L08  Nut Plate 2 ..  709-052L3 
87 NAS1739B4-3  Rivet 8 ..  709-052L3 
88 NAS9301B-4-02  Rivet 80 ..  709-052L3 
89 NAS9301B-4-03  Rivet 28 ..  709-052L3 
90 NAS9301B-4-04  Rivet 12 ..  709-052L3 
91 NAS9301B-5-02  Rivet 12 ..  709-052L3 
92 NAS9301B-5-03  Rivet 10 ..  709-052L3 
93 NAS9301B-5-04  Rivet 10 ..  709-052L3 
94 109G5330R01-203  ANGLE REPAIR INSTALLATION LH REF ..  - 
95 109-0952-67-119  Angle 1 … (12)(17) 709-052L3 
96 109-0952-67-121  Internal Butt-Strap 1 …  709-052L3 
97 MS20470AD5-5  Rivet 0.1kg …  709-052L3 
PART V 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
98 109G5330R01-202  LATERAL MOUNTING REINFORCEMENT REF .  - 
99 109-0320-90-208 109-0320-90-208A1 FWD Cap RH 1 .. (12) 709-052L3 
100 109-0320-90-8  Panel REF .. (6) - 
101 109-0952-67-109  Web 1 .. (12)(15) 709-052L3 
102 109-0952-67-115  External Butt-Strap 1 ..  709-052L3 
103 109G5307P39-114  Angle LH 1 ..  709-052L3 
104 109G5307P39-116  Left Cap 1 ..  709-052L3 
105 109G5307P39-117  Doubler 1 ..  709-052L3 
106 109G5330A25-102  Stiffener Machined LH 1 ..  709-052L3 
107 109G5330R01-206  Doubler LH 1 ..  709-052L3 
108 A879A05L150  Rivet 6 ..  709-052L3 
109 CR2245-4-2  Rivet 1 ..  709-052L3 
110 CR2245-4-5  Rivet 2 ..  709-052L3 
111 CR2245-5-3  Rivet 1 ..  709-052L3 
112 MS20426AD3-5  Rivet 0.1kg ..  709-052L3 
113 MS20426AD4-5  Rivet 0.1kg ..  709-052L3 
114 MS20426AD5-5  Rivet 0.1kg ..  709-052L3 
115 MS20470AD4-5  Rivet 0.1kg ..  709-052L3 
116 MS20470AD5-5  Rivet 0.1kg ..  709-052L3 
117 MS21071L08  Nut Plate 2 ..  709-052L3 
118 NAS1739B4-3  Rivet 8 ..  709-052L3 
119 NAS9301B-4-02  Rivet 80 ..  709-052L3 
120 NAS9301B-4-03  Rivet 28 ..  709-052L3 
121 NAS9301B-4-04  Rivet 12 ..  709-052L3 
122 NAS9301B-5-02  Rivet 12 ..  709-052L3 
123 NAS9301B-5-03  Rivet 10 ..  709-052L3 
124 NAS9301B-5-04  Rivet 10 ..  709-052L3 
125 109G5330R01-204  ANGLE REPAIR INSTALLATION LH REF ..  - 
126 109-0952-67-111  Angle 1 … (12)(16) 709-052L3 
127 109-0952-67-113  Internal Butt-Strap 1 …  709-052L3 
128 MS20470AD5-5  Rivet 0.1kg …  709-052L3

### Page 12

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 11 of 108 
A.2 CONSUMABLES 
The following consumable materials, or equivalent, are necessary to accomplish this 
Service Bulletin: 
# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 
129 199-05-002 TY I, Cl 2 (cod. 900000581) Adhesive EA9309.3NA (C100) AR (8) II, III, IV, V 
130 199-05-004 TY II, Cl 2 (cod. 900001586) Sealant PROSEAL 890B2 (C148) AR (8)(11) II, III, IV, V 
131 AWMS05-001TY I, Cl B, Gr 2 (cod. 999999999000015245) Sealant MC780 B-2 (C501) AR (8)(11) II, III, IV, V 
132 MIL-PRF-23377 TY I, Cl C2 (cod. 999999999000010181) Primer, epoxy-polyamide (446) AR (8) II, III, IV, V 
133 Commercial Soft lint-free cloth (011) AR (8) All 
134 MIL-PRF-680 TY II Cleaning solvent (C287) AR (8) All 
135 Commercial Masking tape (C064) AR (8) II, III, IV, V 
136 Commercial  Scotch-Brite (C015) AR (8) II, III, IV, V 
Refer also to AMDI for the consumable materials required to comply with the MM 
Paragraphs referenced in the accomplishment instructions. 
A.3   LOGISTIC MATRIX 
In order to apply this Service Bulletin, the following Logistic P/N can be ordered in 
accordance with the applicable notes: 
LOGISTIC P/N Q.TY (PER HELO) NOTE PART 
709-052L1 1 (9) II 
709-052L2 1 (10) III 
709-052L3 1 (13) (14) IV, V 
109-0320-90-207 or 109-0320-90-207A1 1 (1) II, IV 
109-0320-90-7 1 (1)(2) II, IV 
109-0320-90-507 1 (3) II, IV 
109-0320-90-505 1 (3)(4) II, IV 
109-0320-90-8 1 (6) III, V 
109-0320-90-208 or 109-0320-90-208A1 1 (12) V 
NOTE 
(1) Item required for helicopters from S/N 11001 thru S/N 11600. 
(2) This item can be obtained reworking the existing panel P/N 109-0320-90-7. 
(3) Item required for helicopters from S/N 11601 thru S/N 11674. 
(4) This item can be obtained reworking the existing panel P/N 109-0320-90-505. 
(5) Seal assy co-pilot door P/N 109-0360-88-109 and seal assy LH passenger door P/N 
109-0360-86-109 will be obtained from gasket P/N A232A001BB. Q.ty 7 m are 
required to comply with Part II of this Service Bulletin. 
(6) This item can be obtained reworking the existing panel P/N 109-0320-90-8. 
(7) Seal assy pilot door P/N 109-0360-88-110 and seal assy RH passenger door P/N 
109-0360-86-110 will be obtained from gasket P/N A232A001BB. Q.ty 7 m are

### Page 13

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 12 of 108 REVISION: B - August 24, 2023 
required to comply with Part III of this Service Bulletin. 
(8) Local supply. 
(9) Required for LH side fuselage repair. 
(10) Required for RH side fuselage repair. 
(11) These materials are alternatives 
(12) Reuse the removed part if it is not damaged. 
(13) Required for LH side fuselage reinforcement. 
(14) Required for RH side fuselage reinforcement. 
(15) This item can be obtained reworking the existing web P/N 109-0320-96-72. 
(16) This item can be obtained reworking the existing RH angle P/N 109-0320-96-74. 
(17) This item can be obtained reworking the existing LH angle P/N 109-0320-96-73. 
(18) This item can be obtained reworking the existing web P/N 109-0320-96-71. 
B. SPECIAL TOOLS 
The following special tools, or equivalent, are necessary to accomplish this Service 
Bulletin: 
# P/N DESCRIPTION Q.TY NOTE PART 
137 109-3000-01-41 or  109-3000-03-143 Flight controls rigging pin set 1 (B1)(B2) II, III, IV, V 
138 GB941-009-000  or equivalent Hydraulic system test bench 1 (B1)(B2) II, III, IV, V 
139 GPU400  or equivalent Electric power unit 1 (B1)(B2) II, III, IV, V 
140 109-3900-01-1 Hoisting ring, main transmission 1 (B1)(B2) II, III, IV, V 
141 109-3000-05-101 Minimum collective lever 1 (B1)(B2) II, IV 
Refer also to PTUM for the special tools required to comply with the MM Paragraphs 
referenced in the accomplishment instructions. 
SPECIAL TOOLS NOTE 
 Commercial item used for general maintenance. Local supply. 
 If necessary, please contact Leonardo Helicopters Division order administration to 
request the tools supply on loan. As soon as the present Service Bulletin is 
implemented the tools supplied on loan shall be promptly returned to Leonardo 
Helicopters Division. 
C. INDUSTRY SUPPORT INFORMATION 
Owners/Operators who comply with the instructions of this Service Bulletin no later than 
the applicable date in the “Compliance” section will be eligible to receive REQUIRED 
MATERIALS on free of charge basis, except for Consumable Materials and Special 
Tools.

### Page 14

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 13 of 108 
NOTE: Customers who fail to comply with the instructions in this Service Bulletin before 
the compliance date are not eligible for the aforementioned special policy. 
Please Issue relevant MMIR form to your Warranty Administration Dpt.

### Page 15

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 14 of 108 REVISION: B - August 24, 2023 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the modification 
area and adequately protect them until their later re-
use. 
b) Shape the cables in order to prevent interference 
with the structure and the other existing installations, 
using where necessary suitable lacing cords. 
c) Exercise extreme care during drilling operations to 
prevent instruments, cables and hoses damage. 
d) After drilling, remove all swarf and sharp edges. 
Apply on bare metal a light film of primer unless the 
hole is used for ground connection. 
e) During the installation of bonding braids or 
components requiring grounding, clean the surface 
structure in order to obtain a good ground contact. 
f) Let adhesive cure at room temperature for at least 
24 hours unless otherwise specified. 
g) Exposed thread surface and nut must be protected 
using a layer of tectyl according to MIL-C-16173 
grade I. 
h) Refer to CSRP-A-CSRP-00-X for the applicable 
structural standard practice procedures. 
i) Refer to AMP Chapter 20 for the applicable standard 
torque values for threaded fasteners. 
j) All lengths are in mm. 
PART I 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. With reference to Figure 1, open both the passenger doors and both the cockpit doors and 
secure them in opened position to gain access to the indicated areas. 
3. If installed, remove any item of furnishing on the passenger compartment that might

### Page 16

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 15 of 108 
prevent the access to the inspection zone. 
4. If installed, in accordance with MM Paragraphs 25-81-7 and 25-81-9, remove the cockpit 
and passenger compartment soundproofing panels or the moquette lining that might 
prevent the access to the inspection zone. 
5. With reference with Figure 2, on both lateral posts, remove the access panels on the aft 
side (P/N 109-0320-96-309 on LH side and P/N 109-0320-96-310 on RH side) and on the 
inboard side (P/N 109-0320-96-521 on LH side and P/N 109-0320-96-522 on RH side). 
Retain all the fixing hardware for later reuse. 
6. If necessary, clean the inspection areas using a soft lint-free cloth (not soaked) and 
cleaning solvent MIL-PRF-680 Type II or equivalent. 
7. With reference to Figure 1, using a bright source of light, visually inspect the whole zone 
of intersection between the lateral post and the floor spar, on both sides of the fuselage, 
for evidence of cracks. Pay particular attention to the forward area of the post (toward 
cockpit) and to inboard side of the post. 
8. In case of no findings, reinstall all the component removed from Step 3 to Step 5 and 
proceed to Step 10. 
9. In case of findings, in accordance with CSRP standard repair procedures perform a 
fluorescent liquid penetrant inspection of the crack to determine the exact extent, then 
stop-drill at both ends of crack to relieve the stresses in the extremities and to prevent any 
further propagation. 
9.1 If the length of crack on the FWD CAP does not exceed 50 mm and no other 
damages are detected in the affected area, proceed in accordance with PART IV 
(LH side of fuselage) or PART V (RH side of fuselage) of this Service Bulletin within 
and not later than the next 25 flight hours otherwise. 
9.2 If the length of crack on the FWD CAP is greater than 50 mm and/or any other 
crack(s) are detected but not exceeding the boundaries of the FWD CAP, INNER 
FORWARD ANGLE or WEB (ref. Figure 1) proceed in accordance with PART IV 
(LH side of fuselage) or PART V (RH side of fuselage) of this Service Bulletin 
before the next flight. 
9.3 If the length of the cracks exceeds the boundaries of the FWD CAP, INNER 
FORWARD ANGLE or WEB (ref. Figure 1), the repair/reinforce scheme reported 
in this Service Bulletin could not be applicable. In this case contact Leonardo 
Engineering Dept at the following mail box: 
engineering.support.lhd@leonardo.com. 
10. Return the helicopter to a ready to flight condition and record for compliance with Part I of 
this Service Bulletin on the helicopter logbook.

### Page 17

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 16 of 108 REVISION: B - August 24, 2023 
11. Gain access to My Communications section on Leonardo WebPortal and compile the 
“Service Bulletin Application Communication”.  
As an alternative, send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardo.com  
and (for North, Central and South America) also to: 
 AWPC.Engineering.Support@leonardocompany.us

### Page 18

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 17 of 108 
PART II 
NOTE 
If undamaged, parts P/N 109-0320-96-71  
(or P/N 109-0320-96-505) and 109-0320-96-73  
(or P/N 109-0320-96-507) may not be cut and reused in 
their respective position. 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. With reference to Figure 11 and Figure 12, remove the collective control rod assy  
P/N 109-0032-02-41 and the tail rotor control rod assy P/N 109-0032-02-25 as follows: 
2.1 In accordance with MM Paragraph 25-11-9, remove the co-pilot seat. 
2.2 If installed, in accordance with MM Paragraph 25-21-12, remove the forward 
passenger seat. 
2.3 In accordance with the pertinent MM Paragraph, remove any other item of 
equipment/furnishing that might prevent the access to the work area. 
2.4 If installed, in accordance with MM Paragraphs 25-81-7 and 25-81-9, remove the 
cockpit and passenger compartment soundproofing panels or the moquette lining 
that might prevent the access to the inspection zone. 
2.5 In accordance with MM Paragraph 21-21-1, remove the air distribution duct P/N 
109-0710-32-105 from the left door post. 
2.6 Remove the access panel P/N 109-0320-90-63. 
2.7 Remove the access door P/N 109-0322-10-13 on the upper part of the fuselage, 
over the door post. 
2.8 Using masking tape, identify the position and the sense of installation of each 
control rod assy. 
2.9 With reference to Figure 11, on the lower end of the collective control rod assy, 
remove the cotter pin, the nut, the bolt and the washers that attach the lower end 
of the control rod assy to the lever. Discard the cotter pin. If necessary, move 
slightly the collective control lever and/or the pedals to allow an easy removal of 
the bolt. 
CAUTION 
During the hardware removing, keep the rod assy to 
prevent it from falling.

### Page 19

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 18 of 108 REVISION: B - August 24, 2023 
2.10 With reference to Figure 11, on the upper end of the collective control rod assy, 
remove the cotter pin, the nut, the bolt and the washers that attach the upper end 
of the control rod assy to the lever. Discard the cotter pin. 
NOTE 
Do not change the length of the collective control rod 
assy. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
2.11 Withdraw the collective control rod assy from t he upper side of helicopter. 
2.12 With reference to Figure 12, on the lower end of the tail rotor control rod assy, 
remove the cotter pin, the nut, the bolt and the washer that attach the lower end of 
the control rod assy to the lever. Discard the cotter pin. 
CAUTION 
During the hardware removing, keep the rod assy to 
prevent it from falling. 
2.13 With reference to Figure 12, on the upper end o f the tail rotor control rod assy, 
remove, the nut, the bolt and the washer that attach the lower end of the control 
rod assy to the lever. Discard the cotter pin. 
NOTE 
Do not change the length of the tail rotor control rod 
assy. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
2.14 Withdraw the tail rotor control rod assy from t he upper side of helicopter. 
3. In accordance with MM Paragraph 52-11-9, remove the pilot and co-pilot door. Open both 
the passenger compartment doors and lock them in opened position. 
4. Remove the co-pilot door seal assy P/N 109-0360-88-109 and the passenger door seal 
assy P/N 109-0360-86-109. Remove any trace of adhesive and rubber from installation 
areas using a plastic scraper and a soft cloth moistened with solvent. 
5. In accordance with MM Paragraph 25-11-9, remove the pilot seat. 
6. Remove the support panels located under the pilot and co-pilot seat. Remove also the

### Page 20

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 19 of 108 
centre panel located between the seats and any control located on it (e.g. friction knob, 
cargo hook release handle). 
7. If installed, in accordance with MM Paragraphs 67-00-12 and 67-11-9, remove the co-pilot 
collective control lever. 
8. Set the collective control in fully-up position then lock the collective torque tube using the 
friction. 
9. Remove the collective lever guard assy P/N 109-0700-25-127 (if the helicopter is equipped 
with dual control) or the fairing P/N 109-0011-28-1 (if the helicopter is not equipped with 
dual control). 
10. Remove and retain for later re-use all the access panels located on the door sill. 
11. With reference to Figure 2, remove the access panels P/N 109-0320-96-521 and  
P/N 109-0320-96-309 located on the post. Retain all the fixing hardware for later reuse. 
12. Remove the air conditioning duct located inside the door lower sill. Cap thoroughly the 
open ends of the adjacent ducts to prevent any unwanted entry of foreign materials in the 
air conditioning system. 
13. Remove the collective stick connector located on the right side of the co-pilot seat support 
structure. Wrap the connector using a plastic sheet and stow it in a safe place. 
14. In accordance with MM Paragraphs 67-00-12 and 67-11-9, remove the collective control 
torque tube. To make easier the reinstallation of the torque tube at the end of the repair, 
it is advisable to mark the position of the following components on the torque tube using a 
thin felt-tip pen: 
 LVDT sensors (collective transducers); 
 Engine-out switch (if installed in accordance with SB 109EP-081); 
 Collective friction; 
 Support on the LH side of the torque tube. 
15. With reference to Figure 13, remove the LH post centre fairing P/N 109-0324-29-101 by 
removing the related attaching screws. 
16. Remove the cockpit/passenger doors caution system switch from the fairing removed at 
previous Step 15 by removing the two attaching screws. Leave the switch attached to the 
wire. Take note of quantity of shims below the switch in order to allow the reinstallation in 
their original position. 
17. If applied, remove any sill-liner or anti-slip paint from the upper side of the fairings P/N 
109-0324-25-303 and 109-0324-30-201. 
18. In accordance with MM Paragraphs 07-30-1 or 07-30-2, raise the helicopter using the 
lifting device P/N 109-3900-01-1 connected to a suitable crane/hoist and put the cable in 
tension.

### Page 21

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 20 of 108 REVISION: B - August 24, 2023 
19. With reference to Figure 13, remove the LH lower fairing P/N 109-0324-25-303 by drilling-
out the attaching rivets. Break the sealant layer between the fairing and the structure using 
a thin blade or putty knife. 
20. With reference to Figure 13, remove the LH post lower fairing P/N 109-0324-30-201 by 
drilling-out the attaching rivets. Break the sealant layer between the fairing and the 
structure using a thin blade or putty knife. 
21. Remove any trace of sealant from the structure and from the inner side of the fairings P/N 
109-0324-25-303 and 109-0324-30-201 using a plastic scraper or putty knife. Clean 
thoroughly using Scotch-Brite and a clean, lint-free cloth moistened with cleaning solvent 
MIL-PRF-680 TY II. 
22. Drill-out all the rivets that attach the forward LH cap, the forward LH protection P/N  
109-0311-40-133 and the doubler P/N 109-0311-40-128 (under the forward LH protection 
P/N 109-0311-40-133). Break the sealant layer between the cap, the protection, the 
doubler and the structure using a thin blade or putty knife. Remove any trace of sealant 
from the structure using a plastic scraper or putty knife. Clean thoroughly using Scotch-
Brite and a clean, lint-free cloth moistened with cleaning solvent MIL-PRF-680 TY II. 
23. If installed, remove and retain for later reuse any additional shim that is installed between 
the rear part of the forward LH cap and the post structure. 
NOTE 
For A109E helicopters from S/N 11001 thru S/N 11600 
included. 
24. With reference to Figure 15, temporarily remove the internal doubler, then put the new 
forward LH cap P/N 109-0320-90-207 or -207A1 in the same position as the removed one. 
If necessary, remove some rivets on the post to allow an easy positioning. 
NOTE 
For A109E helicopters from S/N 11601 thru S/N 11674 
included. 
25. With reference to Figure 15, temporarily remove the internal doubler, then put the new 
forward LH cap P/N 109-0320-90-507 (in the same position as the removed one. If 
necessary, remove some rivets on the post to allow an easy positioning. 
26. In order to fit the new forward cap to the existing structure, proceed as follow: 
26.1 With reference to Figure 15, trim the forward end to the necessary length. 
26.2 With reference to Figure 20, trim the two tabs at the aft end to the necessary length 
and shape. 
26.3 With reference to Figure 22, mark and cut the round notch for the torque tube. 
26.4 Mark and drill some holes to temporary secure the forward LH cap to the structure.

### Page 22

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 21 of 108 
26.5 With reference to Figure 15, put in position the forward steel external protection 
and secure it in position in the forward part with Cleco fasteners. This allows the 
use the aft holes to complete the drilling of the new FWD LH cap. 
26.6 With reference to Figure 14, drill all the remaining holes, except the holes in the 
upper external side for attachment of external fairings P/N 109-0324-25-303 and 
109-0324-30-201. 
26.7 Using the holes in the spar as a reference, drill the two Ø 6.25 mm holes for 
attachment of the support P/N 109-0011-18-1 of the torque tube. 
27. With reference to Figure 16 thru Figure 18, find and mark the cutting line for the web P/N  
109-0320-96-71 (or P/N 109-0320-96-505). Identify and remove all the rivets that attach 
the web to LH angle P/N 109-0320-96-73 (or P/N 109-0320-96-507), to forward and aft 
bulkhead P/N 109-0320-96, and to LH ribs P/N 109-0320-96-47 and P/N 109-0320-96-49. 
Using a putty knife, break the sealant/adhesive between the parts. 
28. With reference to Figure 20, identify and remove the twelve additional rivets that attach 
the web P/N 109-0320-96-71 (or P/N 109-0320-96-505) to the forward and aft bulkheads. 
They must be removed to allow installation, at the end of the repair procedure, of the 
external butt-strap P/N 109-0952-67-123. 
29. Remove the rivets that have been identified and marked in the previous Steps 27 and 28. 
NOTE 
Insert a thin steel sheet between the web and the 
forward and aft bulkheads to avoid damages while 
cutting the metal. 
30. With reference to Figure 17, cut the web P/N 109 -0320-96-71 (or P/N 109-0320-96-505). 
31. With reference to Figure 17, identify and mark the cutting lines for angle  
P/N 109-0320-96-73 (or P/N 109-0320-96-507). The slant of cut shown in figure is 
indicative. Always make sure that cutting lines are equally spaced from the adjacent rivets. 
Identify all the rivets that attach the portion of angle to other structural elements of the 
post. 
32. With reference to Figure 17, remove the rivets identified in the previous Step 31. 
33. With reference to Figure 16 and Figure 19, remove the four rivets that attach the two nut-
plates to the forward side of the post. Discard the two nut-plates. 
34. With reference to Figure 16 and Figure 17, cut the angle P/N 109-0320-96-73  
(or P/N 109-0320-96-507). 
35. With reference to Figure 16 thru Figure 22, put the new angle P/N 109-0952-67-119, the 
new butt strap P/N 109-0952-67-121 and the web P/N 109-0952-67-125 in position on 
interior of the post. Mark the exact length of the angle P/N 109-0952-67-119, depending

### Page 23

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 22 of 108 REVISION: B - August 24, 2023 
on the cutting position of the existing angle. 
36. With reference to Figure 23 and Figure 24, mark the exact length of the internal butt-strap 
P/N 109-0952-67-121. 
NOTE 
When marking the position of the rivet holes, make sure 
that the distance between the hole centre and the edge 
of the sheet is at least 2.5 times the diameter of the rivet. 
37. Remove the new angle P/N 109-0952-67-119 and the  new butt strap  
P/N 109-0952-67-121 and cut them to the exact length as defined in Steps 35 and 36. 
Reinstall the items in position and mark the position of the rivet holes. 
38. Drill the holes to attach the new angle P/N 109-0952-67-119, the new butt strap P/N 109-
0952-67-121 and the web P/N 109-0952-67-125 to the forward bulkhead  
P/N 109-0320-96. Attach the parts in position with Cleco fasteners. 
39. Put the web P/N 109-0952-67-125 in position on the post. Drill the holes to secure the new 
internal butt strap P/N 109-0952-67-121. 
40. With reference to Figure 20, put the external butt-strap P/N 109-0952-67-123 in position. 
If necessary, adapt the shape to the profile of the post to allow the correct installation. 
Mark and drill the attachment holes. 
41. With reference to Figure 23 and Figure 24, cut the oversize material from the external  
butt-strap. 
42. Remove the paint from the existing web P/N 109-0320-96-71 (or P/N 109-0320-96-505) 
and from the new web P/N 109-0952-67-125 in the area of installation of the external  
butt-strap P/N 109-0952-67-123. 
NOTE 
For accessibility reason, it is allowed to install rivets P/N 
A879A05L150 on opposite direction (rivet from outside 
to inside STA1815 honeycomb). 
43. With reference to Figure 19 thru Figure 22, put in position the new angle  
P/N 109-0952-67-119, the new butt strap P/N 109-0952-67-121 and the web  
P/N 109-0952-67-125. Bond the internal butt-strap P/N 109-0952-67-121 with adhesive 
EA9309.3NA. Starting from the forward side of the post, install the rivets. 
44. With reference to Figure 19 thru Figure 22, bond the external butt-strap  
P/N 109-0952-67-123 to the post using adhesive EA9309.3NA and rivets. Seal edges of 
external butt-strap P/N 109-0952-67-123 using PROSEAL 890B2. 
45. With reference to Figure 19, reinstall and bond with adhesive EA9309.3NA all the shims 
that were installed under the lower end of forward LH bulkhead P/N 109-0320-96.

### Page 24

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 23 of 108 
NOTE 
Make sure that the rivets in the zone of installation of the 
torque tube support P/N 109-0011-18-1 have the 
countersunk head on both sides. Make sure that the 
head does not protrude over the surface. Flush the 
heads if necessary. 
NOTE 
For A109E helicopters from S/N 11001 thru S/N 11600 
included. 
46. With reference to Figure 14 and Figure 15, put t he forward cap P/N 109-0320-90-207 or -
207A1 in position and bond with PROSEAL 890B2. Install the forward cap using the same 
type of rivets as previously removed or the alternate rivets. 
NOTE 
For A109E helicopters from S/N 11601 thru S/N 11674 
included. 
47. With reference to Figure 14 and Figure 15, put t he forward cap P/N 109-0320-90-507 in 
position and bond with PROSEAL 890B2. Install the forward cap using the same type of 
rivets as previously removed or the alternate rivets 
48. Seal the edges of the forward LH cap using sealant PROSEAL 890B2. 
49. Seal the edges of the external butt-strap P/N 109-0952-67-123 and of the web  
P/N 109-0952-67-125 using sealant PROSEAL 890B2. 
50. With reference to Figure 19, install the two nutplates MS21071L08 and MS21069L08 in 
position. Use the collective lever guard assy P/N 109-0700-25-127 (if the helicopter is 
equipped with dual control) or the fairing P/N 109-0011-28-1 (if the helicopter is not 
equipped with dual control) to mark the position of the nutplates. 
51. Temporarily put the LH post lower fairing P/N 109-0324-30-201 and the LH lower fairing 
P/N 109-0324-25-303 in position and drill the rivet holes in the upper part of the forward 
LH cap P/N 109-0320-90-207 or -207A1 or -507. 
52. Touch-up the exposed areas of the repaired zones with primer and paint to restore the 
original aspect. 
53. With reference to Figure 13, bond with PROSEAL 890B2 then attach with rivets the LH 
lower fairing P/N 109-0324-25-303. Make sure that that the drain holes in the fairing are 
not plugged by the sealant. 
54. With reference to Figure 13, bond with PROSEAL 890B2 then attach with rivets the LH 
post lower fairing P/N 109-0324-30-201. Make sure that that the drain holes in the fairing 
are not plugged by the sealant.

### Page 25

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 24 of 108 REVISION: B - August 24, 2023 
55. In accordance with MM Paragraphs 07-30-1 or 07-30-2, lay down the helicopter. 
56. Reinstall the cockpit/passenger doors caution system switch on the LH post centre fairing 
P/N 109-0324-29-101 using the related screws. Put the shims (if any) in their original 
position. 
57. With reference to Figure 13, reinstall the LH post centre fairing P/N 109-0324-29-101 using 
the related attaching screws. 
58. If originally installed, reinstall the sill-liner or apply the anti-slip paint on the upper side of 
the fairings P/N 109-0324-25-303 and 109-0324-30-201. 
59. Reinstall the cockpit and passenger doors seals. 
60. In accordance with MM Paragraph 21-21-1, reinstall the air conditioning duct located 
inside the door lower sill. 
61. Reinstall the collective stick connector removed at Step 13. 
62. In accordance with MM Paragraphs 67-00-12 and 67-11-9, reinstall the collective control 
torque tube. 
63. If removed (Ref. Step 7), in accordance with MM Paragraphs 67-00-12 and 67-11-9, 
reinstall the co-pilot collective control lever. 
64. With reference to Figure 11 and Figure 12, reinstall the collective control rod assy P/N 
109-0032-04-41 and the tail rotor control rod assy P/N 109-0032-02-25 as follows: 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
64.1 Put the collective control rod assy in position  on interior of the left cabin post by 
inserting it from the top. Observe the correct sense of installation, as identified in 
previous Step 2.8. 
64.2 Attach the upper end of the collective control rod assy to the lever using the bolt 
AN174-12, the washer A160A0432K (under bolt head and with countersunk side 
toward the bolt head), the washer AN960-PD416 (under the nut) and the nut 
MS17825-4. Torque the nut to 3.4 thru 4.5 Nm and install a new cotter pin 
MS24665-153. 
64.3 Attach the lower end of the collective control rod assy to the lever using the bolt 
AN174-12, the washer A160A0432K (under bolt head and with countersunk side 
toward the bolt head), the washer AN960-PD416 (under the nut) and the nut 
MS17825-4. If necessary, move slightly the collective control lever as necessary 
to allow the insertion of the bolt. Torque the nut to 3.4 thru 4.5 Nm and install a 
new cotter pin MS24665-153.

### Page 26

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 25 of 108 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
64.4 Put the tail rotor control rod assy in position  on interior of the left cabin post by 
inserting it from the top. Observe the correct sense of installation, as identified in 
previous Step 2.8. 
64.5 Attach the upper end of the tail rotor control rod assy to the lever using the bolt 
AN174-12, the washer AN960-PD416 under the nut and the nut MS17825-4. 
Torque the nut to 3.4 thru 4.5 Nm and install a new cotter pin MS24665-151. 
64.6 Attach the lower end of the tail rotor control rod assy to the lever using the bolt 
AN174-12, the washer AN960-PD416 under the nut and the nut MS17825-4. If 
necessary, move slightly the pedals as necessary to allow the insertion of the bolt. 
Torque the nut to 3.4 thru 4.5 Nm and install a new cotter pin MS24665-151. 
64.7 Remove the masking tape that has been put on the rods to identify the direction of 
installation (ref. Step 2.8). 
64.8 Perform a duplicate inspection of installation of the control rods. The duplicate 
inspection must include, but is not limited to, correct assembly, security, correct 
application of cotter pins, thread engagement and protrusion, and a functional 
check for complete range, freedom of movement and operation in correct sense. 
65. For the collective installation affected by collective control rod assy P/N 109-0032-02-41 
and Torque Tube removal and re-installation, perform the following step of MM Paragraph 
67-00-25 (ref. Figures 3 thru 10): 
 Put the minimum collective lever positioning Tool (LSE 198) in its position on the 
interseat console; 
 Move the pilot collective stick down and put the lower side of the stick against the 
pin of the tool. Being collective control rod assy P/N 109-0032-02-41 mechanically 
connected to the lower and upper lever, as per Step 64.2 and 64.3, also the mixing 
unit will be moved FWD. Pay attention to provide hydraulic power supply at 1500 
PSI before moving the stick; 
 Check that the minimum Collective Stop is engaged as per Step X. If not, apply the 
following Step from Step A up to Step H; 
 Remove the Tool (minimum collective lever) from the cockpit; 
 Loosen the adjustable friction; 
 Move the collective stick three or four times. Make sure that the collective controls 
are free to operate without friction against the structure.

### Page 27

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 26 of 108 REVISION: B - August 24, 2023 
 In accordance with MM Paragraph 67-11-16, adjust fixed friction. 
66. Perform an operational test of the collective control system, and of the tail rotor control 
system, to make sure that the control linkages move freely. 
67. Reinstall all the access panels you have removed to perform the repair. 
NOTE 
For A109E helicopters from S/N 11001 thru S/N 11600 
included. 
68. Panel P/N 109-0320-90-7, removed at Step 10, can  be reused after removing thoroughly 
any trace of sealant using a plastic scraper and a cloth moistened with solvent  
MIL-PRF-680 TY II. 
NOTE 
For A109E helicopters from S/N 11601 thru S/N 11674 
included. 
69. Panel P/N 109-0320-90-505, removed at Step 10, c an be reused after removing 
thoroughly any trace of sealant using a plastic scraper and a cloth moistened with solvent  
MIL-PRF-680 TY II. 
70. Reinstall the collective lever guard assy P/N 109-0700-25-127 (if the helicopter is 
equipped with dual control) or the fairing P/N 109-0011-28-1 (if the helicopter is not 
equipped with dual control). 
71. Reinstall the support panels located under the pilot and co-pilot seat. Reinstall also the 
centre panel located between the seats and any control located on it (e.g. friction knob, 
cargo hook release handle). 
72. Reinstall the access door P/N 109-0322-10-13 on the upper part of the fuselage, over the 
door post, and move the platform away from helicopter. 
73. Reinstall the access panel P/N 109-0320-90-63. 
74. In accordance with MM Paragraph 21-21-1, reinstall the air distribution duct  
P/N 109-0710-32-105 on the door post. 
75. With reference to the pertinent MM Paragraph, reinstall all the items of 
equipment/furnishing that were removed to gain access to work area. 
76. If originally installed, in accordance with MM Paragraph 25-21-12, reinstall the forward 
passenger seat. 
77. In accordance with MM Paragraph 25-11-9, reinstall the pilot and co-pilot seat. 
78. If originally installed, in accordance with MM Paragraphs 25-81-7 and 25-81-9, reinstall 
the cockpit and passenger compartment soundproofing panels or the moquette lining. 
79. In accordance with MM Paragraph 52-11-9, reinstall the pilot and co-pilot doors and close 
the passenger compartment doors.

### Page 28

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 27 of 108 
80. In accordance with MM Paragraph 52-71-6, perform an operational test of the 
cockpit/passenger doors caution system. 
81. Return the helicopter to a ready to flight condition and record for compliance with Part II 
of this Service Bulletin on the helicopter logbook. 
82. Gain access to My Communications section on Leonardo WebPortal and compile the 
“Service Bulletin Application Communication”.  
As an alternative, send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardo.com  
and (for North, Central and South America) also to: 
 AWPC.Engineering.Support@leonardocompany.us

### Page 29

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 28 of 108 REVISION: B - August 24, 2023 
PART III 
NOTE 
If undamaged, parts P/N 109-0320-96-72  
(or P/N 109-0320-96-506) and 109-0320-96-74  
(or P/N 109-0320-96-508) may not be cut and reused in 
their respective position. 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. With reference to Figure 25 and Figure 26, remove the lateral cyclic control rod assy  
P/N 109-0032-19-101 and the longitudinal cyclic control rod assy P/N 109-0032-07-01 as 
follows: 
2.1 In accordance with MM Paragraph 25-11-9, remove the pilot seat. 
2.2 If installed, in accordance with MM Paragraph 25-21-12, remove the forward 
passenger seat. 
2.3 In accordance with the pertinent MM Paragraph, remove any other item of 
equipment/furnishing that might prevent the access to the work area. 
2.4 If installed, in accordance with MM Paragraphs 25-81-7 and 25-81-9, remove the 
cockpit and passenger compartment soundproofing panels or the moquette lining 
that might prevent the access to the inspection zone. 
2.5 In accordance with MM Paragraph 21-21-1, remove the air distribution duct P/N 
109-0710-32-105 from the left door post. 
2.6 Remove the access panel 109-0320-90-206. 
2.7 Remove the access door P/N 109-0322-10-14 on the upper part of the fuselage, 
over the door post. 
2.8 Using masking tape, identify the position and the sense of installation of each 
control rod assy. 
2.9 With reference to Figure 25, on the lower end of the lateral cyclic control rod assy, 
remove the cotter pin, the nut, the bolt and the washers that attach the lower end 
of the control rod assy to the lever. Discard the cotter pin. If necessary, move 
slightly the cyclic control stick to allow an easy removal of the bolt. 
CAUTION 
During the hardware removing, keep the rod assy to 
prevent it from falling.

### Page 30

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 29 of 108 
2.10 With reference to Figure 25, on the upper end of the lateral cyclic control rod assy, 
remove the cotter pin, the nut, the bolt and the washers that attach the upper end 
of the control rod assy to the lever. Discard the cotter pin. 
NOTE 
Do not change the length of the lateral cyclic control rod 
assy. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
2.11 Withdraw the lateral cyclic control rod assy to ward the upper side of helicopter. 
2.12 With reference to Figure 26, on the lower end of the longitudinal cyclic control rod 
assy, remove the cotter pin, the nut, the bolt and the washers that attach the lower 
end of the control rod assy to the lever. Discard the cotter pin. 
CAUTION 
During the hardware removing, keep the rod assy to 
prevent it from falling. 
2.13 With reference to Figure 26, on the upper end o f the longitudinal cyclic control rod 
assy, remove the cotter pin, the nut, the bolt and the washers that attach the upper 
end of the control rod assy to the lever. Discard the cotter pin. 
NOTE 
Do not change the length of the longitudinal cyclic 
control rod. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
2.14 Withdraw the longitudinal cyclic control rod to ward the upper side of helicopter. 
3. In accordance with MM Paragraph 52-11-9, remove the pilot and co-pilot door. Open both 
the passenger compartment doors and lock them in opened position. 
4. Remove the pilot door seal assy P/N 109-0360-88-110 and the passenger door seal assy 
P/N 109-0360-86-110. Remove any trace of adhesive and rubber from installation areas 
using a plastic scraper and a soft cloth moistened with solvent. 
5. In accordance with MM Paragraph 25-11-9, remove the co-pilot seat. 
6. Remove the support panels located under the pilot and co-pilot seat. Remove also the

### Page 31

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 30 of 108 REVISION: B - August 24, 2023 
centre panel located between the seats and any control located on it (e.g. friction knob, 
cargo hook release handle). 
7. Remove and retain for later re-use all the access panels located on the door sill. 
8. With reference to Figure 2, remove the access panels P/N 109-0320-96-522 and  
P/N 109-0320-96-310 located on the post. Retain all the fixing hardware for later reuse. 
9. Remove the air conditioning duct located inside the door lower sill. Cap thoroughly the 
open ends of the adjacent ducts to prevent any unwanted entry of foreign materials in the 
air conditioning system. 
10. In accordance with MM Paragraphs 67-00-12 and 67-12-1, remove and retain for later 
reuse the following components of the flight control system: 
 Lateral cyclic control rod P/N 109-0032-01-1; 
 Longitudinal cyclic control rod P/N 109-0032-03-1; 
 Lateral cyclic lever P/N 109-0020-17-1; 
 Lateral cyclic control rod P/N 109-0032-02-1. 
11. With reference to figure 13, remove the RH post centre fairing P/N 109-0324-29-102 by 
removing the related attaching screws. 
12. Remove the cockpit/passenger doors caution system switch from the fairing removed at 
previous Step 11 by removing the two attaching screws. Leave the switch attached to the 
wire. Take note of quantity of shims below the switch in order to allow the reinstallation in 
their original position. 
13. If applied, remove any sill-liner or anti-slip paint from the upper side of the fairings P/N 
109-0324-25-304 and 109-0324-30-202. 
14. In accordance with MM Paragraphs 07-30-1 or 07-30-2, raise the helicopter using the 
lifting device P/N 109-3900-01-1 connected to a suitable crane/hoist and put the cable in 
tension. 
15. With reference to Figure 27, remove the RH lower fairing P/N 109-0324-25-304 by drilling-
out the attaching rivets. Break the sealant layer between the fairing and the structure using 
a thin blade or putty knife. 
16. With reference to Figure 27, remove the RH post lower fairing P/N 109-0324-30-202 by 
drilling-out the attaching rivets. Break the sealant layer between the fairing and the 
structure using a thin blade or putty knife. 
17. Remove any trace of sealant from the structure and from the inner side of the fairings P/N 
109-0324-25-304 and 109-0324-30-202 using a plastic scraper or putty knife. Clean 
thoroughly using Scotch-Brite and a clean, lint-free cloth moistened with cleaning solvent 
MIL-PRF-680 TY II. 
18. Drill-out all the rivets that attach the forward RH cap, the forward RH protection P/N

### Page 32

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 31 of 108 
109-0311-40-134 and the doubler P/N 109-0311-40-128 (under the forward RH protection 
P/N 109-0311-40-134). Break the sealant layer between the cap, the protection, the 
doubler and the structure using a thin blade or putty knife. Remove any trace of sealant 
from the structure using a plastic scraper or putty knife. Clean thoroughly using Scotch-
Brite and a clean, lint-free cloth moistened with cleaning solvent MIL-PRF-680 TY II. 
19. If installed, remove and retain for later reuse any additional shim that is installed between 
the rear part of the forward RH cap and the post structure. 
20. With reference to Figure 28, temporarily remove the internal doubler, then put the new 
forward RH cap P/N 109-0320-90-208 or -208A1 in the same position as the removed 
one. If necessary, remove some rivets on the post to allow an easy positioning. 
21. In order to fit the new forward cap to the existing structure, proceed as follow: 
21.1 With reference to Figure 28, trim the forward end to the necessary length. 
21.2 With reference to Figure 33 and Figure 34, trim the two tabs at the aft end to the 
necessary length and shape. 
21.3 Mark and drill some holes to temporary secure the forward RH cap to the structure. 
21.4 With reference to Figure 28, put in position the forward steel external protection 
and secure it in position in the forward part with Cleco fasteners. This allows the 
use the aft holes to complete the drilling of the new FWD RH cap. 
21.5 With reference to Figure 28, drill all the remaining holes, except the holes in the 
upper external side for attachment of external fairings P/N 109-0324-25-304 and 
109-0324-30-202. 
22. With reference to Figure 29 thru Figure 31, find and mark the cutting line for the web P/N  
109-0320-96-72 (or P/N 109-0320-96-506). Identify and remove all the rivets that attach 
the web to RH angle P/N 109-0320-96-74 (or P/N 109-0320-96-508), to forward and aft 
bulkhead P/N 109-0320-96, and to RH ribs P/N 109-0320-96-48 and P/N 109-0320-96-
50. Using a putty knife, break the sealant/adhesive between the parts. 
23. With reference to Figure 33 and Figure 34, identify and remove the twelve additional rivets 
that attach the web P/N 109-0320-96-72 (or P/N 109-0320-96-506) to the forward and aft 
bulkheads. They must be removed to allow installation, at the end of the repair procedure, 
of the external butt-strap P/N 109-0952-67-115. 
24. Remove the rivets that have been identified and marked in the previous Steps 22 and 23. 
NOTE 
Insert a thin steel sheet between the web and the 
forward and aft bulkheads to avoid damages while 
cutting the metal. 
25. With reference to Figure 30, cut the web P/N 109 -0320-96-72 (or P/N 109-0320-96-506).

### Page 33

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 32 of 108 REVISION: B - August 24, 2023 
26. With reference to Figure 30, identify and mark the cutting lines for angle P/N  
109-0320-96-74 (or P/N 109-0320-96-508). The slant of cut shown in figure is indicative. 
Always make sure that cutting lines are equally spaced from the adjacent rivets. Identify 
all the rivets that attach the portion of angle to other structural elements of the post. 
27. With reference to Figure 30, remove the rivets identified in the previous Step 26. 
28. With reference to Figure 29 and Figure 30, cut the angle P/N 109-0320-96-74  
(or P/N 109-0320-96-508). 
29. With reference to Figure 29 thru Figure 34, put the new angle P/N 109-0952-67-111, the 
new internal butt strap P/N 109-0952-67-113 and the web P/N 109-0952-67-109 in 
position on interior of the post. Mark the exact length of the angle P/N 109-0952-67-111, 
depending on the cutting position of the existing angle. 
30. With reference to Figure 35 and Figure 36, mark the exact length of the internal butt-strap 
P/N 109-0952-67-113. 
NOTE 
When marking the position of the rivet holes, make sure 
that the distance between the hole centre and the edge 
of the sheet is at least 2.5 times the diameter of the rivet. 
31. Remove the new angle P/N 109-0952-67-111 and the  new butt strap  
P/N 109-0952-67-113 and cut them to the exact length as defined in Steps 29 and 30 
above. Reinstall the items in position and mark the position of the rivet holes. 
32. Drill the holes to attach the new angle P/N 109-0952-67-111, the new butt strap  
P/N 109-0952-67-113 and the web P/N 109-0952-67-109 to the forward bulkhead  
P/N 109-0320-96. Attach the parts in position with Cleco fasteners. 
33. Put the web P/N 109-0952-67-109 in position on the post. Drill the holes to secure the new 
butt strap P/N 109-0952-67-113. 
34. With reference to Figure 33 and Figure 34, put the external butt-strap  
P/N 109-0952-67-115 in position. If necessary, adapt the shape to the profile of the post 
to allow the correct installation. Mark and drill the attachment holes. 
35. With reference to Figure 35 and Figure 36, cut the oversize material from the external butt-
strap. 
36. Remove the paint from the existing web P/N 109-0320-96-72 (or P/N 109-0320-96-506) 
and from the new web P/N 109-0952-67-109 in the area of installation of the external butt-
strap P/N 109-0952-67-115.

### Page 34

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 33 of 108 
NOTE 
For accessibility reason, it is allowed to install rivets P/N 
A879A05L150 on opposite direction (rivet from outside 
to inside STA1815 honeycomb). 
37. With reference to Figure 32 thru Figure 34, put in position the new angle  
P/N 109-0952-67-111, the new butt strap P/N 109-0952-67-113 and the web  
P/N 109-0952-67-109. Bond the internal butt-strap P/N 109-0952-67-113 with 
EA9309.3NA. Starting from the forward side of the post, install the rivets. 
38. With reference to Figure 32 thru Figure 34, bond the external butt-strap  
P/N 109-0952-67-115 to the post using EA9309.3NA adhesive and rivets. Seal edges of 
external butt-strap P/N 109-0952-67-115 using PROSEAL 890B2. 
39. With reference to Figure 32, reinstall and bond with EA9309.3NA all the shims that were 
installed under the lower end of forward RH bulkhead P/N 109-0320-96. 
NOTE 
Make sure that the rivets in the zone of installation of the 
torque tube support P/N 109-0011-18-1 have the 
countersunk head on both sides. Make sure that the 
head does not protrude over the surface. Flush the 
heads if necessary. 
40. With reference to Figure 28, put the forward cap  P/N 109-0320-90-208 or -208A1 in 
position and bond with PROSEAL 890B2. Install the forward cap using the same type of 
rivets as previously removed or the alternate rivets. 
41. Seal the edges of the forward RH cap using sealant PROSEAL 890B2. 
42. Seal the edges of the external butt-strap P/N 109-0952-67-115 and of the web  
P/N 109-0952-67-109 using sealant PROSEAL 890B2. 
43. Temporarily put the RH post lower fairing P/N 109-0324-30-202 and the RH lower fairing 
P/N 109-0324-25-304 in position and drill the rivet holes in the upper part of the forward 
RH cap P/N 109-0320-90-208 or -208A1. 
44. Touch-up the exposed areas of the repaired zones with primer and paint to restore the 
original aspect. 
45. With reference to Figure 27, bond with PROSEAL 890B2 then attach with rivets the RH 
lower fairing P/N 109-0324-25-304. Make sure that that the drain holes in the fairing are 
not plugged by the sealant. 
46. With reference to Figure 27, bond with PROSEAL 890B2 then attach with rivets the RH 
post lower fairing P/N 109-0324-30-202. Make sure that that the drain holes in the fairing 
are not plugged by the sealant.

### Page 35

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 34 of 108 REVISION: B - August 24, 2023 
47. In accordance with MM Paragraphs 07-30-1 or 07-30-2, lay down the helicopter. 
48. Reinstall the cockpit/passenger doors caution system switch on the RH post centre fairing 
P/N 109-0324-29-102 using the related screws. Put the shims (if any) in their original 
position. 
49. With reference to Figure 27, reinstall the LH post centre fairing P/N 109-0324-29-102 using 
the related attaching screws. 
50. If originally installed, reinstall the sill-liner or apply the anti-slip paint on the upper side of 
the fairings P/N 109-0324-25-304 and 109-0324-30-202. 
51. Reinstall the cockpit and passenger doors seals. 
52. In accordance with MM Paragraphs 67-00-12 and 67-12-1, reinstall the following 
components of the flight control system: 
 Lateral cyclic control rod P/N 109-0032-01-1; 
 Longitudinal cyclic control rod P/N 109-0032-03-1; 
 Lateral cyclic lever P/N 109-0020-17-1; 
 Lateral cyclic control rod P/N 109-0032-02-1. 
53. In accordance with MM Paragraph 21-21-1, reinstall the air conditioning duct located 
inside the door lower sill. 
54. With reference to Figure 25 and Figure 26, reinstall the lateral cyclic control rod assy and 
the longitudinal cyclic control rod assy P/N 109-0032-07-01 as follows: 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
54.1 Put the longitudinal control rod assy in positi on on interior of the right cabin post by 
inserting it from the top. Observe the correct sense and position of installation, as 
identified in previous Step 2.8. 
54.2 With reference to Figure 26, attach the upper end of the longitudinal control rod to 
the lever using the bolt AN174-12, one washer AN960-PD416 (under the bolt 
head), one washer AN960-PD416 under the nut, and the nut MS17825-4. Torque 
the nut to 3.4 thru 4.5 Nm and install a new cotter pin MS24665-153. If necessary, 
install one additional washer AN960-PD416 under the nut to obtain the correct 
engagement of the nut.

### Page 36

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 35 of 108 
54.3 With reference to Figure 26, attach the lower end of the longitudinal control rod to 
the lever using the bolt AN174-12, one washer AN960-PD416 (under the bolt 
head), one washer AN960-PD416 under the nut, and the nut MS17825-4. If 
required, move slightly cyclic control stick as necessary to allow the insertion of the 
bolt. Torque the nut to 3.4 thru 4.5 Nm and install a new cotter pin  
MS24665-153. If necessary, install one additional washer AN960-PD416 under the 
nut to obtain the correct engagement of the nut. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
54.4 Put the lateral control rod assy in position on  interior of the right cabin post by 
inserting it from the top. Observe the correct sense and position of installation, as 
identified in previous Step 2.8. 
54.5 With reference to Figure 25, attach the upper end of the lateral control rod to the 
lever using the bolt AN174-12, one washer AN960-PD416 (under the bolt head), 
one washer AN960-PD416 under the nut, and the nut MS17825-4. Torque the nut 
to 3.4 thru 4.5 Nm and install a new cotter pin MS24665-153. If necessary, install 
one additional washer AN960-PD416 under the nut to obtain the correct 
engagement of the nut. 
54.6 With reference to Figure 25, attach the lower end of the lateral control rod) to the 
lever using the bolt AN174-12, one washer AN960-PD416 (under the bolt head), 
one washer AN960-PD416 under the nut, and the nut MS17825-4. If required, 
move slightly cyclic control stick as necessary to allow the insertion of the bolt. 
Torque the nut to 3.4 thru 4.5 Nm and install a new cotter pin MS24665-153. If 
necessary, install one additional washer AN960-PD416 under the nut to obtain the 
correct engagement of the nut. 
54.7 Remove the masking tape that has been put on the rods to identify the direction of 
installation (ref. Step 2.8). 
54.8 Perform a duplicate inspection of installation of the control rods. The duplicate 
inspection must include, but is not limited to, correct assembly, security, correct 
application of cotter pins, thread engagement and protrusion, and a functional 
check for complete range, freedom of movement and operation in correct sense. 
55. To check that the Fixed Flight Component have been properly re-installed, get access to 
the cyclic control stick on the left side of the cockpit, and with hydraulic power supply at 
1500 PSI perform the following Step of MM Paragraph 67-00-26, (ref. Figures 3 thru 10):

### Page 37

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 36 of 108 REVISION: B - August 24, 2023 
 Disengage the spring P/N 109-0020-36 from the bracket; 
 Fully loosen the friction control; 
 Step B; 
 Step C. If rigging pins do not fit, apply MM Paragraph 67-00-26; 
 Engage the spring P/N 109-0020-36 on bracket; 
 Step H; 
 Do the adjustment of the fixed frictions of the cyclic control system. 
56. Perform an operational test of the cyclic control system to make sure that the control 
linkages move freely. 
57. Reinstall all the access panels you have removed to perform the repair. 
58. Panel P/N 109-0320-90-8, removed at Step 7, can be reused after removing thoroughly 
any trace of sealant using a plastic scraper and a cloth moistened with solvent  
MIL-PRF-680 TY II. 
59. Reinstall the support panels located under the pilot and co-pilot seat. Reinstall also the 
centre panel located between the seats and any control located on it (e.g. friction knob, 
cargo hook release handle). 
60. Reinstall the access door P/N 109-0322-10-14 on the upper part of the fuselage, over the 
door post, and move the platform away from helicopter. 
61. Reinstall the access panel P/N 109-0320-90-206. 
62. In accordance with MM Paragraph 21-21-1, reinstall the air distribution duct  
P/N 109-0710-32-106 on the door post. 
63. With reference to the pertinent MM Paragraph, reinstall all the items of 
equipment/furnishing that were removed to gain access to work area. 
64. If originally installed, in accordance with MM Paragraph 25-21-12, reinstall the forward 
passenger seat. 
65. In accordance with MM Paragraph 25-11-9, reinstall the pilot and co-pilot seat. 
66. If originally installed, in accordance with MM Paragraphs 25-81-7 and 25-81-9, reinstall 
the cockpit and passenger compartment soundproofing panels or the moquette lining. 
67. In accordance with MM Paragraph 52-11-9, reinstall the pilot and co-pilot doors and close 
the passenger compartment doors. 
68. In accordance with MM Paragraph 52-71-6, perform an operational test of the 
cockpit/passenger doors caution system.  
69. Return the helicopter to a ready to flight condition and record for compliance with Part III 
of this Service Bulletin on the helicopter logbook. 
70. Gain access to My Communications section on Leonardo WebPortal and compile the 
“Service Bulletin Application Communication”.

### Page 38

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 37 of 108 
As an alternative, send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardo.com  
and (for North, Central and South America) also to: 
 AWPC.Engineering.Support@leonardocompany.us

### Page 39

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 38 of 108 REVISION: B - August 24, 2023 
PART IV 
NOTE 
If the helicopter’s LH post has been repaired in 
accordance with Part II (LH side) of this Service Bulletin, 
or in accordance with repair drawing P/N 109-0952-67-
117 (LH side), the helicopter could install web with P/N 
109-0320-96-71 (or P/N 109-0320-96-505 or P/N 109-
0952-67-125), and LH angle with P/N 109-0320-96-73 
(or P/N 109-0320-96-507 or P/N 109-0952-67-119). 
NOTE 
If undamaged, parts P/N 109-0320-96-71  
(or P/N 109-0320-96-505) and 109-0320-96-73  
(or P/N 109-0320-96-507) may not be cut and reused in 
their respective position. 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. With reference to Figure 11 and Figure 12, remove the collective control rod assy  
P/N 109-0032-02-41 and the tail rotor control rod assy P/N 109-0032-02-25 as follows: 
2.1 In accordance with MM Paragraph 25-11-9, remove the co-pilot seat. 
2.2 If installed, in accordance with MM Paragraph 25-21-12, remove the forward 
passenger seat. 
2.3 In accordance with the pertinent MM Paragraph, remove any other item of 
equipment/furnishing that might prevent the access to the work area. 
2.4 If installed, in accordance with MM Paragraphs 25-81-7 and 25-81-9, remove the 
cockpit and passenger compartment soundproofing panels or the moquette lining 
that might prevent the access to the inspection zone. 
2.5 In accordance with MM Paragraph 21-21-1, remove the air distribution duct  
P/N 109-0710-32-105 from the left door post. 
2.6 Remove the access panel P/N 109-0320-90-63. 
2.7 Remove the access door P/N 109-0322-10-13 on the upper part of the fuselage, 
over the door post. 
2.8 Using masking tape, identify the position and the sense of installation of each 
control rod assy.

### Page 40

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 39 of 108 
2.9 With reference to Figure 11, on the lower end of the collective control rod assy, 
remove the cotter pin, the nut, the bolt and the washers that attach the lower end 
of the control rod assy to the lever. Discard the cotter pin. If necessary, move 
slightly the collective control lever and/or the pedals to allow an easy removal of 
the bolt. 
CAUTION 
During the hardware removing, keep the rod assy to 
prevent it from falling. 
2.10 With reference to Figure 11, on the upper end o f the collective control rod assy, 
remove the cotter pin, the nut, the bolt and the washers that attach the upper end 
of the control rod assy to the lever. Discard the cotter pin. 
NOTE 
Do not change the length of the collective control rod 
assy. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
2.11 Withdraw the collective control rod assy from t he upper side of helicopter. 
2.12 With reference to Figure 12, on the lower end of the tail rotor control rod assy, 
remove the cotter pin, the nut, the bolt and the washer that attach the lower end of 
the control rod assy to the lever. Discard the cotter pin. 
CAUTION 
During the hardware removing, keep the rod assy to 
prevent it from falling. 
2.13 With reference to Figure 12, on the upper end o f the tail rotor control rod assy, 
remove, the nut, the bolt and the washer that attach the lower end of the control 
rod assy to the lever. Discard the cotter pin. 
NOTE 
Do not change the length of the tail rotor control rod 
assy. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter.

### Page 41

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 40 of 108 REVISION: B - August 24, 2023 
2.14 Withdraw the tail rotor control rod assy from the upper side of helicopter. 
3. In accordance with MM Paragraph 52-11-9, remove the pilot and co-pilot door. Open both 
the passenger compartment doors and lock them in opened position. 
4. Remove the co-pilot door seal assy P/N 109-0360-88-109 and the passenger door seal 
assy P/N 109-0360-86-109. Remove any trace of adhesive and rubber from installation 
areas using a plastic scraper and a soft cloth moistened with solvent. 
5. In accordance with MM Paragraph 25-11-9, remove the pilot seat. 
6. Remove the support panels located under the pilot and co-pilot seat. Remove also the 
centre panel located between the seats and any control located on it (e.g. friction knob, 
cargo hook release handle). 
7. If installed, in accordance with MM Paragraphs 67-00-12 and 67-11-9, remove the co-pilot 
collective control lever. 
8. Set the collective control in fully-up position then lock the collective torque tube using the 
friction. 
9. Remove the collective lever guard assy P/N 109-0700-25-127 (if the helicopter is equipped 
with dual control) or the fairing P/N 109-0011-28-1 (if the helicopter is not equipped with 
dual control). 
10. Remove and retain for later re-use all the access panels located on the door sill. 
11. With reference to Figure 2, remove the access panels P/N 109-0320-96-521 and  
P/N 109-0320-96-309 located on the post. Retain all the fixing hardware for later reuse. 
12. Remove the air conditioning duct located inside the door lower sill. Cap thoroughly the 
open ends of the adjacent ducts to prevent any unwanted entry of foreign materials in the 
air conditioning system. 
13. Remove the collective stick connector located on the right side of the co-pilot seat support 
structure. Wrap the connector using a plastic sheet and stow it in a safe place. 
14. In accordance with MM Paragraphs 67-00-12 and 67-11-9, remove the collective control 
torque tube. To make easier the reinstallation of the torque tube at the end of the repair, 
it is advisable to mark the position of the following components on the torque tube using a 
thin felt-tip pen:  
 LVDT sensors (collective transducers); 
 Engine-out switch (if installed in accordance with SB 109EP-081); 
 Collective friction; 
 Support on the LH side of the torque tube. 
15. With reference to Figure 13, remove the LH post centre fairing P/N 109-0324-29-101 by 
removing the related attaching screws. 
16. Remove the cockpit/passenger doors caution system switch from the fairing removed at

### Page 42

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 41 of 108 
previous Step 15 by removing the two attaching screws. Leave the switch attached to the 
wire. Take note of quantity of shims below the switch in order to allow the reinstallation in 
their original position. 
17. If applied, remove any sill-liner or anti-slip paint from the upper side of the fairings  
P/N 109-0324-25-303 and 109-0324-30-201. 
18. In accordance with MM Paragraphs 07-30-1 or 07-30-2, raise the helicopter using the 
lifting device P/N 109-3900-01-1 connected to a suitable crane/hoist and put the cable in 
tension. 
19. With reference to Figure 13, remove the LH lower fairing P/N 109-0324-25-303 by drilling-
out the attaching rivets. Break the sealant layer between the fairing and the structure using 
a thin blade or putty knife. 
20. With reference to Figure 13, remove the LH post lower fairing P/N 109-0324-30-201 by 
drilling-out the attaching rivets. Break the sealant layer between the fairing and the 
structure using a thin blade or putty knife. 
21. Remove any trace of sealant from the structure and from the inner side of the fairings  
P/N 109-0324-25-303 and 109-0324-30-201 using a plastic scraper or putty knife. Clean 
thoroughly using Scotch-Brite and a clean, lint-free cloth moistened with cleaning solvent 
MIL-PRF-680 TY II. 
22. Drill-out all the rivets that attach the forward LH cap, the forward LH protection  
P/N 109-0311-40-133 and the doubler P/N 109-0311-40-128 (under the forward LH 
protection P/N 109-0311-40-133). Break the sealant layer between the cap, the protection, 
the doubler and the structure using a thin blade or putty knife. Remove any trace of sealant 
from the structure using a plastic scraper or putty knife. Clean thoroughly using Scotch-
Brite and a clean, lint-free cloth moistened with cleaning solvent MIL-PRF-680 TY II. 
23. If installed, remove and retain for later reuse any additional shim that is installed between 
the rear part of the forward LH cap and the post structure. 
24. With reference to Figure 38, remove the forward LH cap P/N 109-0320-90-207 or -507. 
Discard only if the part is damaged. 
25. With reference to Figure 38, remove the left cap P/N 109-0320-90-53. 
26. With reference to Figure 40 View E-E, temporarily remove the FWD bulkhead LH  
P/N 109-0320-96-311, the LH core P/N 109-0320-90-117 and the LH angle  
P/N 109-0320-90-41. 
27. With reference to Figure 41, remove the filler P/N 109-0320-90-175. 
28. With reference to Figure 38, install the LH angle P/N 109G5307P39-113 by means of 
adhesive EA9309.3NA. 
29. With reference to Figure 41, install the stiffener machined LH P/N 109G5330A25-101 by 
means of adhesive EA9309.3NA.

### Page 43

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 42 of 108 REVISION: B - August 24, 2023 
30. With reference to Figure 37 thru Figure 41, install the following parts by means of the 
indicated rivets: 
 the left cap P/N 109G5307P39-115; 
 the doubler P/N 109G5307P39-117; 
 the previously removed FWD bulkhead LH P/N 109-0320-96-311, 
 the previously removed LH core P/N 109-0320-90-117; 
 the previously removed LH angle P/N 109-0320-90-41. 
31. With reference to Figure 42 thru Figure 47, find and mark the cutting line for the web  
P/N 109-0320-96-71 (or P/N 109-0320-96-505). Identify and remove all the rivets that 
attach the web to LH angle P/N 109-0320-96-73 (or P/N 109-0320-96-507), to forward and 
aft bulkhead P/N 109-0320-96, and to LH ribs P/N 109-0320-96-47 and P/N 109-0320-96-
49. Using a putty knife, break the sealant/adhesive between the parts. 
32. With reference to Figure 43, identify and remove the twelve additional rivets that attach 
the web P/N 109-0320-96-71 (or P/N 109-0320-96-505) to the forward and aft bulkheads. 
They must be removed to allow installation of the external butt-strap P/N 109-0952-67-
123. 
33. Remove the rivets that have been identified and marked in the previous Steps 31 and 32. 
NOTE 
Insert a thin steel sheet between the web and the 
forward and aft bulkheads to avoid damages while 
cutting the metal. 
34. With reference to Figure 42 thru Figure 44, cut the web P/N 109-0320-96-71  
(or P/N 109-0320-96-505). 
NOTE 
Perform the following Steps from 35 to 47 ONLY if the 
angle P/N 109-0320-96-73 (or P/N 109-0320-96-507) is 
damaged, otherwise skip to Step 48. 
35. With reference to Figure 43, identify and mark t he cutting lines for angle  
P/N 109-0320-96-73 (or P/N 109-0320-96-507). The slant of cut shown in figure is 
indicative. Always make sure that cutting lines are equally spaced from the adjacent rivets. 
Identify all the rivets that attach the portion of angle to other structural elements of the 
post. 
36. With reference to Figure 43, remove the rivets identified in the previous Step 35. 
37. With reference to Figure 41 and Figure 42, remove the four rivets that attach the two nut-
plates to the forward side of the post. Discard the two nut-plates.

### Page 44

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 43 of 108 
38. With reference to Figure 45 and Figure 46, cut the angle P/N 109-0320-96-73  
(or P/N 109-0320-96-507). 
39. With reference to Figure 42 thru Figure 47, put the new angle P/N 109-0952-67-119, the 
new butt strap P/N 109-0952-67-121, the web P/N 109-0952-67-125 and the doubler P/N 
109G5330R01-205 in position on interior of the post. Mark the exact length of the angle 
P/N 109-0952-67-119, depending on the cutting position of the existing angle. 
40. With reference to Figure 45 and Figure 46, mark the exact length of the internal butt-strap 
P/N 109-0952-67-121. 
NOTE 
When marking the position of the rivet holes, make sure 
that the distance between the hole centre and the edge 
of the sheet is at least 2.5 times the diameter of the rivet. 
41. Remove the new angle P/N 109-0952-67-119 and the  new butt strap  
P/N 109-0952-67-121 and cut them to the exact length as defined in Steps 39 and 40. 
Reinstall the items in position and mark the position of the rivet holes. 
42. Drill the holes to attach the new angle P/N 109-0952-67-119, the new butt strap  
P/N 109-0952-67-121, the web P/N 109-0952-67-125 and the doubler  
P/N 109G5330R01-205 to forward and aft bulkhead P/N 109-0320-96. Attach the parts in 
position with Cleco fasteners. 
43. Put the web P/N 109-0952-67-125 in position on the post. Drill the holes to secure the new 
internal butt strap P/N 109-0952-67-121. 
44. With reference to Figure 43, put the external butt-strap P/N 109-0952-67-123 in position. 
If necessary, adapt the shape to the profile of the post to allow the correct installation. 
Mark and drill the attachment holes. 
45. Remove the paint from the existing web P/N 109-0320-96-71 (or P/N 109-0320-96-505) 
and from the new web P/N 109-0952-67-125 in the area of installation of the external butt-
strap P/N 109-0952-67-123. 
NOTE 
For accessibility reason, it is allowed to install rivets  
P/N A879A05L150 on opposite direction (rivet from 
outside to inside STA1815 honeycomb). 
46. With reference to Figure 42 thru Figure 47, put in position the new angle  
P/N 109-0952-67-119, the new butt strap P/N 109-0952-67-121, the web  
P/N 109-0952-67-125 and the doubler P/N 109G5330R01-205. Install by means of 
adhesive EA9309.3NA. Starting from the forward side of the post, install the rivets. Seal 
edges by means of sealant PROSEAL 890B2 or MC780 B-2.

### Page 45

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 44 of 108 REVISION: B - August 24, 2023 
47. With reference to Figure 42 thru Figure 44, install the external butt-strap  
P/N 109-0952-67-123 to the post by means of adhesive EA9309.3NA and rivets. Seal 
edges by means of sealant PROSEAL 890B2 or MC780 B-2. 
NOTE 
Perform the following Steps from 48 to 54 ONLY if the 
angle P/N 109-0320-96-73 (or P/N 109-0320-96-507) is 
undamaged. 
48. With reference to Figure 41 and Figure 42, remov e the four rivets that attach the two  
nut-plates to the forward side of the post. Discard the two nut-plates. 
49. With reference to Figure 42 thru Figure 44, put the web P/N 109-0952-67-125 and the 
doubler P/N 109G5330R01-205 in position on interior of the post. 
NOTE 
When marking the position of the rivet holes, make sure 
that the distance between the hole centre and the edge 
of the sheet is at least 2.5 times the diameter of the rivet. 
50. Drill the holes to attach the the web P/N 109-09 52-67-125 and the doubler  
P/N 109G5330R01-205 to forward and aft bulkhead P/N 109-0320-96. Attach the parts in 
position with Cleco fasteners. 
51. With reference to Figure 43, put the external butt-strap P/N 109-0952-67-123 in position. 
If necessary, adapt the shape to the profile of the post to allow the correct installation. 
Mark and drill the attachment holes. 
52. Remove the paint from the existing web P/N 109-0320-96-71 (or P/N 109-0320-96-505) 
and from the new web P/N 109-0952-67-125 in the area of installation of the external  
butt-strap P/N 109-0952-67-123. 
NOTE 
For accessibility reason, it is allowed to install rivets  
P/N A879A05L150 on opposite direction (rivet from 
outside to inside STA1815 honeycomb). 
53. With reference to Figure 42 thru Figure 44, put in position the web  
P/N 109-0952-67-125 and the doubler P/N 109G5330R01-205. Install by means of 
adhesive EA9309.3NA. Starting from the forward side of the post, install the rivets. Seal 
edges by means of sealant PROSEAL 890B2 or MC780 B-2. 
54. With reference to Figure 42 thru Figure 44, install the external butt-strap  
P/N 109-0952-67-123 to the post by means of adhesive EA9309.3NA and rivets. Seal 
edges by means of sealant PROSEAL 890B2 or MC780 B-2. 
55. With reference to Figure 19, reinstall and bond with adhesive EA9309.3NA all the shims

### Page 46

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 45 of 108 
that were installed under the lower end of forward LH bulkhead P/N 109-0320-96. 
NOTE 
Make sure that the rivets in the zone of installation of the 
torque tube support P/N 109-0011-18-1 have the 
countersunk head on both sides. Make sure that the 
head does not protrude over the surface. Flush the 
heads if necessary. 
NOTE 
Reuse the removed part if it is not damaged. 
56. With reference to Figure 38, Figure 39 and Figur e 48, put the forward cap  
P/N 109-0320-90-207 or -507 in position and bond by means of adhesive EA9309.3NA 
and PROSEAL 890B2. Install the forward cap by means of the indicated rivets. Seal the 
edges of the forward LH cap by means of sealant PROSEAL 890B2 or MC780 B-2. 
57. With reference to Figure 41 and 42, install the two nutplates P/N MS21071L08 in the 
indicated position by means of the rivets. 
58. Temporarily put the LH post lower fairing P/N 109-0324-30-201 and the LH lower fairing 
P/N 109-0324-25-303 in position and drill the rivet holes in the upper part of the forward 
LH cap P/N 109-0320-90-207 or -507. 
59. Touch-up the exposed areas of the repaired zones with primer and paint to restore the 
original aspect. 
60. With reference to Figure 13, bond with PROSEAL 890B2 then attach with rivets the LH 
lower fairing P/N 109-0324-25-303. Make sure that that the drain holes in the fairing are 
not plugged by the sealant. 
61. With reference to Figure 13, bond with PROSEAL 890B2 then attach with rivets the LH 
post lower fairing P/N 109-0324-30-201. Make sure that that the drain holes in the fairing 
are not plugged by the sealant. 
62. In accordance with MM Paragraphs 07-30-1 or 07-30-2, lay down the helicopter. 
63. Reinstall the cockpit/passenger doors caution system switch on the LH post centre fairing 
P/N 109-0324-29-101 using the related screws. Put the shims (if any) in their original 
position. 
64. With reference to Figure 13, reinstall the LH post centre fairing P/N 109-0324-29-101 using 
the related attaching screws. 
65. If originally installed, reinstall the sill-liner or apply the anti-slip paint on the upper side of 
the fairings P/N 109-0324-25-303 and P/N 109-0324-30-201. 
66. Reinstall the cockpit and passenger doors seals. 
67. In accordance with MM Paragraph 21-21-1, reinstall the air conditioning duct located

### Page 47

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 46 of 108 REVISION: B - August 24, 2023 
inside the door lower sill. 
68. Reinstall the collective stick connector removed at Step 13. 
69. In accordance with MM Paragraphs 67-00-12 and 67-11-9, reinstall the collective control 
torque tube. 
70. If removed (Ref. Step 7), in accordance with MM Paragraphs 67-00-12 and 67-11-9, 
reinstall the co-pilot collective control lever. 
71. With reference to Figure 11 and Figure 12, reinstall the collective control rod assy  
P/N 109-0032-04-41 and the tail rotor control rod assy P/N 109-0032-02-25 as follows: 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
71.1 Put the collective control rod assy in position  on interior of the left cabin post by 
inserting it from the top. Observe the correct sense of installation, as identified in 
previous Step 2.8. 
71.2 Attach the upper end of the collective control rod assy to the lever using the bolt 
P/N AN174-12, the washer P/N A160A0432K (under bolt head and with 
countersunk side toward the bolt head), the washer P/N AN960-PD416 (under the 
nut) and the nut P/N MS17825-4. Torque the nut to 3.4 thru 4.5 Nm and install a 
new cotter pin P/N MS24665-153. 
71.3 Attach the lower end of the collective control rod assy to the lever using the bolt 
P/N AN174-12, the washer P/N A160A0432K (under bolt head and with 
countersunk side toward the bolt head), the washer P/N AN960-PD416 (under the 
nut) and the nut P/N MS17825-4. If necessary, move slightly the collective control 
lever as necessary to allow the insertion of the bolt. Torque the nut to 3.4 thru  
4.5 Nm and install a new cotter pin P/N MS24665-153. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
71.4 Put the tail rotor control rod assy in position  on interior of the left cabin post by 
inserting it from the top. Observe the correct sense of installation, as identified in 
previous Step 2.8.

### Page 48

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 47 of 108 
71.5 Attach the upper end of the tail rotor control rod assy to the lever using the bolt  
P/N AN174-12, the washer P/N AN960-PD416 under the nut and the nut  
P/N MS17825-4. Torque the nut to 3.4 thru 4.5 Nm and install a new cotter pin  
P/N MS24665-151. 
71.6 Attach the lower end of the tail rotor control rod assy to the lever using the bolt  
P/N AN174-12, the washer P/N AN960-PD416 under the nut and the nut  
P/N MS17825-4. If necessary, move slightly the pedals as necessary to allow the 
insertion of the bolt. Torque the nut to 3.4 thru 4.5 Nm and install a new cotter pin 
P/N MS24665-151. 
71.7 Remove the masking tape that has been put on the rods to identify the direction of 
installation (ref. Step 2.8). 
71.8 Perform a duplicate inspection of installation of the control rods. The duplicate 
inspection must include, but is not limited to, correct assembly, security, correct 
application of cotter pins, thread engagement and protrusion, and a functional 
check for complete range, freedom of movement and operation in correct sense. 
72. For the collective installation affected by collective control rod assy P/N 109-0032-02-41 
and Torque Tube removal and re-installation, perform the following step of MM Paragraph 
67-00-25 (ref. Figures 3 thru 10): 
 Put the minimum collective lever positioning Tool (LSE 198) in its position on the 
interseat console; 
 Move the pilot collective stick down and put the lower side of the stick against the 
pin of the tool. Being collective control rod assy P/N 109-0032-02-41 mechanically 
connected to the lower and upper lever, as per Step 71.2 and 71.3, also the mixing 
unit will be moved FWD. Pay attention to provide hydraulic power supply at 1500 
PSI before moving the stick; 
 Check that the minimum Collective Stop is engaged as per Step X. If not, apply the 
following Step from Step A up to Step H; 
 Remove the Tool (minimum collective lever) from the cockpit; 
 Loosen the adjustable friction; 
 Move the collective stick three or four times. Make sure that the collective controls 
are free to operate without friction against the structure. 
 In accordance with MM Paragraph 67-11-16, adjust fixed friction. 
73.  Perform an operational test of the collective control system, and of the tail rotor control 
system, to make sure that the control linkages move freely. 
74. Reinstall all the access panels you have removed to perform the repair.

### Page 49

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 48 of 108 REVISION: B - August 24, 2023 
NOTE 
For A109E helicopters from S/N 11001 thru S/N 11600 
included. 
75. Panel P/N 109-0320-90-7, removed at Step 10, can  be reused after removing thoroughly 
any trace of sealant using a plastic scraper and a cloth moistened with solvent  
MIL-PRF-680 TY II. 
NOTE 
For A109E helicopters from S/N 11601 thru S/N 11674 
included. 
76. Panel P/N 109-0320-90-505, removed at Step 10, c an be reused after removing 
thoroughly any trace of sealant using a plastic scraper and a cloth moistened with solvent 
MIL-PRF-680 TY II. 
77. Reinstall the collective lever guard assy P/N 109-0700-25-127 (if the helicopter is 
equipped with dual control) or the fairing P/N 109-0011-28-1 (if the helicopter is not 
equipped with dual control). 
78. Reinstall the support panels located under the pilot and co-pilot seat. Reinstall also the 
centre panel located between the seats and any control located on it (e.g. friction knob, 
cargo hook release handle). 
79. Reinstall the access door P/N 109-0322-10-13 on the upper part of the fuselage, over the 
door post, and move the platform away from helicopter. 
80. Reinstall the access panel P/N 109-0320-90-63. 
81. In accordance with MM Paragraph 21-21-1, reinstall the air distribution duct  
P/N 109-0710-32-105 on the door post. 
82. With reference to the pertinent MM Paragraph, reinstall all the items of 
equipment/furnishing that were removed to gain access to work area. 
83. If originally installed, in accordance with MM Paragraph 25-21-12, reinstall the forward 
passenger seat. 
84. In accordance with MM Paragraph 25-11-9, reinstall the pilot and co-pilot seat. 
85. If originally installed, in accordance with MM Paragraphs 25-81-7 and 25-81-9, reinstall 
the cockpit and passenger compartment soundproofing panels or the moquette lining.  
86. In accordance with MM Paragraph 52-11-9, reinstall the pilot and co-pilot doors and close 
the passenger compartment doors. 
87. In accordance with MM Paragraph 52-71-6, perform an operational test of the 
cockpit/passenger doors caution system. 
88. In accordance with weight and balance changes, update the Chart A (see Rotorcraft Flight 
Manual, Part II, section 6).

### Page 50

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 49 of 108 
89. Return the helicopter to a ready to flight condition and record for compliance with Part IV 
of this Service Bulletin on the helicopter logbook. 
90. Gain access to My Communications section on Leonardo WebPortal and compile the 
“Service Bulletin Application Communication”.  
As an alternative, send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardo.com  
and (for North, Central and South America) also to: 
 AWPC.Engineering.Support@leonardocompany.us

### Page 51

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 50 of 108 REVISION: B - August 24, 2023 
PART V 
NOTE 
If the helicopter’s LH post has been repaired in 
accordance with Part III (RH side) of this Service 
Bulletin, or in accordance with repair drawing P/N 109-
0952-67-102 (RH side), the helicopter could install web 
with P/N 109-0320-96-72 (or P/N 109-0320-96-506 or 
P/N 109-0952-67-109), and RH angle with  
P/N 109-0320-96-74 (or P/N 109-0320-96-508 or  
P/N 109-0952-67-111). 
NOTE 
If undamaged, parts P/N 109-0320-96-72  
(or P/N 109-0320-96-506) and 109-0320-96-74  
(or P/N 109-0320-96-508) may not be cut and reused in 
their respective position. 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. With reference to Figure 25 and Figure 26, remove the lateral cyclic control rod assy  
P/N 109-0032-19-101 and the longitudinal cyclic control rod assy P/N 109-0032-07-01 as 
follows: 
2.1 In accordance with MM Paragraph 25-11-9, remove the pilot seat. 
2.2 If installed, in accordance with MM Paragraph 25-21-12, remove the forward 
passenger seat. 
2.3 In accordance with the pertinent MM Paragraph, remove any other item of 
equipment/furnishing that might prevent the access to the work area. 
2.4 If installed, in accordance with MM Paragraphs 25-81-7 and 25-81-9, remove the 
cockpit and passenger compartment soundproofing panels or the moquette lining 
that might prevent the access to the inspection zone. 
2.5 In accordance with MM Paragraph 21-21-1, remove the air distribution duct  
P/N 109-0710-32-105 from the left door post. 
2.6 Remove the access panel P/N 109-0320-90-206. 
2.7 Remove the access door P/N 109-0322-10-14 on the upper part of the fuselage, 
over the door post. 
2.8 Using masking tape, identify the position and the sense of installation of each 
control rod assy.

### Page 52

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 51 of 108 
2.9 With reference to Figure 25, on the lower end of the lateral cyclic control rod assy, 
remove the cotter pin, the nut, the bolt and the washers that attach the lower end 
of the control rod assy to the lever. Discard the cotter pin. If necessary, move 
slightly the cyclic control stick to allow an easy removal of the bolt. 
CAUTION 
During the hardware removing, keep the rod assy to 
prevent it from falling. 
2.10 With reference to Figure 25, on the upper end o f the lateral cyclic control rod assy, 
remove the cotter pin, the nut, the bolt and the washers that attach the upper end 
of the control rod assy to the lever. Discard the cotter pin. 
NOTE 
Do not change the length of the lateral cyclic control rod 
assy. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
2.11 Withdraw the lateral cyclic control rod assy to ward the upper side of helicopter. 
2.12 With reference to Figure 26, on the lower end of the longitudinal cyclic control rod 
assy, remove the cotter pin, the nut, the bolt and the washers that attach the lower 
end of the control rod assy to the lever. Discard the cotter pin. 
CAUTION 
During the hardware removing, keep the rod assy to 
prevent it from falling. 
2.13 With reference to Figure 26, on the upper end o f the longitudinal cyclic control rod 
assy, remove the cotter pin, the nut, the bolt and the washers that attach the upper 
end of the control rod assy to the lever. Discard the cotter pin. 
NOTE 
Do not change the length of the longitudinal cyclic 
control rod assy. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter.

### Page 53

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 52 of 108 REVISION: B - August 24, 2023 
2.14 Withdraw the longitudinal cyclic control rod assy toward the upper side of 
helicopter. 
3. In accordance with MM Paragraph 52-11-9, remove the pilot and co-pilot door. Open both 
the passenger compartment doors and lock them in opened position. 
4. Remove the pilot door seal assy P/N 109-0360-88-110 and the passenger door seal assy 
P/N 109-0360-86-110. Remove any trace of adhesive and rubber from installation areas 
using a plastic scraper and a soft cloth moistened with solvent. 
5. In accordance with MM Paragraph 25-11-9, remove the co-pilot seat. 
6. Remove the support panels located under the pilot and co-pilot seat. Remove also the 
centre panel located between the seats and any control located on it (e.g. friction knob, 
cargo hook release handle). 
7. Remove and retain for later re-use all the access panels located on the door sill  
8. With reference to Figure 2, remove the access panels P/N 109-0320-96-522 and  
P/N 109-0320-96-310 located on the post. Retain all the fixing hardware for later reuse. 
9. Remove the air conditioning duct located inside the door lower sill. Cap thoroughly the 
open ends of the adjacent ducts to prevent any unwanted entry of foreign materials in the 
air conditioning system. 
10. In accordance with MM Paragraphs 67-00-12 and 67-12-1, remove and retain for later 
reuse the following components of the flight control system: 
 Lateral cyclic control rod P/N 109-0032-01-1; 
 Longitudinal cyclic control rod P/N 109-0032-03-1; 
 Lateral cyclic lever P/N 109-0020-17-1; 
 Lateral cyclic control rod P/N 109-0032-02-1. 
11. With reference to figure 13, remove the RH post centre fairing P/N 109-0324-29-102 by 
removing the related attaching screws. 
12. Remove the cockpit/passenger doors caution system switch from the fairing removed at 
previous Step 11 by removing the two attaching screws. Leave the switch attached to the 
wire. Take note of quantity of shims below the switch in order to allow the reinstallation in 
their original position. 
13. If applied, remove any sill-liner or anti-slip paint from the upper side of the fairings  
P/N 109-0324-25-304 and 109-0324-30-202. 
14. In accordance with MM Paragraphs 07-30-1 or 07-30-2, raise the helicopter using the 
lifting device P/N 109-3900-01-1 connected to a suitable crane/hoist and put the cable in 
tension. 
15. With reference to Figure 27, remove the RH lower fairing P/N 109-0324-25-304 by drilling-
out the attaching rivets. Break the sealant layer between the fairing and the structure using

### Page 54

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 53 of 108 
a thin blade or putty knife. 
16. With reference to Figure 27, remove the RH post lower fairing P/N 109-0324-30-202 by 
drilling-out the attaching rivets. Break the sealant layer between the fairing and the 
structure using a thin blade or putty knife. 
17. Remove any trace of sealant from the structure and from the inner side of the fairings  
P/N 109-0324-25-304 and 109-0324-30-202 using a plastic scraper or putty knife. Clean 
thoroughly using Scotch-Brite and a clean, lint-free cloth moistened with cleaning solvent 
MIL-PRF-680 TY II. 
18. Drill-out all the rivets that attach the forward RH cap, the forward RH protection  
P/N 109-0311-40-134 and the doubler P/N 109-0311-40-128 (under the forward RH 
protection P/N 109-0311-40-134). Break the sealant layer between the cap, the protection, 
the doubler and the structure using a thin blade or putty knife. Remove any trace of sealant 
from the structure using a plastic scraper or putty knife. Clean thoroughly using Scotch-
Brite and a clean, lint-free cloth moistened with cleaning solvent MIL-PRF-680 TY II. 
19. If installed, remove and retain for later reuse any additional shim that is installed between 
the rear part of the forward RH cap and the post structure. 
20. With reference to Figure 38, remove the forward RH cap P/N 109-0320-90-208. Discard 
only if the part is damaged. 
21. With reference to Figure 38, remove the right cap P/N 109-0320-90-54. 
22. With reference to Figure 40 View E-E, temporarily remove the FWD bulkhead RH  
P/N 109-0320-96-312, the RH core P/N 109-0320-90-118 and the RH angle  
P/N 109-0320-90-42. 
23. With reference to Figure 41, remove the filler P/N 109-0320-90-175. 
24. With reference to Figure 38, install the RH angle P/N 109G5307P39-114 by means of 
adhesive EA9309.3NA. 
25. With reference to Figure 41, install the stiffener machined RH 109G5330A25-102 by 
means of adhesive EA9309.3NA. 
26. With reference to Figure 37 thru Figure 41, install the following parts by means of the 
indicated rivets: 
 the left cap P/N 109G5307P39-116; 
 the doubler P/N 109G5307P39-117; 
 the previously removed FWD bulkhead RH P/N 109-0320-96-312, 
 the previously removed RH core P/N 109-0320-90-118; 
 the previously removed LH angle P/N 109-0320-90-42. 
27. With reference to Figure 42 thru Figure 47, find and mark the cutting line for the web  
P/N 109-0320-96-72 (or P/N 109-0320-96-506). Identify and remove all the rivets that

### Page 55

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 54 of 108 REVISION: B - August 24, 2023 
attach the web to RH angle P/N 109-0320-96-74 (or P/N 109-0320-96-508), to forward 
and aft bulkhead P/N 109-0320-96, and to RH ribs P/N 109-0320-96-48 and  
P/N 109-0320-96-50. Using a putty knife, break the sealant/adhesive between the parts. 
28. With reference to Figure 43, identify and remove the twelve additional rivets that attach 
the web P/N 109-0320-96-72 to the forward and aft bulkheads. They must be removed to 
allow installation of the external butt-strap P/N 109-0952-67-115. 
29. Remove the rivets that have been identified and marked in the previous Steps 27 and 28. 
NOTE 
Insert a thin steel sheet between the web and the 
forward and aft bulkheads to avoid damages while 
cutting the metal. 
30. With reference to Figure 42 thru Figure 44, cut the web P/N 109-0320-96-72  
(or P/N 109-0320-96-506). 
NOTE 
Perform the following Steps from 31 to 43 ONLY if the 
angle P/N 109-0320-96-74 (or P/N 109-0320-96-508) is 
damaged, otherwise skip to Step 44. 
31. With reference to Figure 43, identify and mark t he cutting lines for angle  
P/N 109-0320-96-74 (or P/N 109-0320-96-508). The slant of cut shown in figure is 
indicative. Always make sure that cutting lines are equally spaced from the adjacent rivets. 
Identify all the rivets that attach the portion of angle to other structural elements of the 
post. 
32. With reference to Figure 43, remove the rivets identified in the previous Step 31. 
33. With reference to Figure 41 and Figure 42, remove the four rivets that attach the two  
nut-plates to the forward side of the post. Discard the two nut-plates. 
34. With reference to Figure 41 and Figure 42, cut the angle P/N 109-0320-96-74  
(or P/N 109-0320-96-508). 
35. With reference to Figure 42 thru Figure 47, put the new angle P/N 109-0952-67-111, the 
new internal butt strap P/N 109-0952-67-113, the web P/N 109-0952-67-109 the doubler 
P/N 109G5330R01-206 in position on interior of the post. Mark the exact length of the 
angle P/N 109-0952-67-111, depending on the cutting position of the existing angle. 
36. With reference to Figure 45 and Figure 46, mark the exact length of the internal  
butt-strap P/N 109-0952-67-113.

### Page 56

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 55 of 108 
NOTE 
When marking the position of the rivet holes, make sure 
that the distance between the hole centre and the edge 
of the sheet is at least 2.5 times the diameter of the rivet. 
37. Remove the new angle P/N 109-0952-67-111 and the  new butt strap  
P/N 109-0952-67-113 and cut them to the exact length as defined in Steps 35 and 36 
above. Reinstall the items in position and mark the position of the rivet holes. 
38. Drill the holes to attach the new angle P/N 109-0952-67-111, the new butt strap P/N  
109-0952-67-113, the web P/N 109-0952-67-109 and the doubler  
P/N 109G5330R01-206 to forward and aft bulkhead P/N 109-0320-96. Attach the parts in 
position with Cleco fasteners. 
39. Put the web P/N 109-0952-67-109 in position on the post. Drill the holes to secure the new 
butt strap P/N 109-0952-67-113. 
40. With reference to Figure 42, put the external butt-strap  
P/N 109-0952-67-115 in position. If necessary, adapt the shape to the profile of the post 
to allow the correct installation. Mark and drill the attachment holes. 
41. Remove the paint from the existing web P/N 109-0320-96-72 (or P/N 109-0320-96-506) 
and from the new web P/N 109-0952-67-109 in the area of installation of the external  
butt-strap P/N 109-0952-67-115. 
NOTE 
For accessibility reason, it is allowed to install rivets P/N 
A879A05L150 on opposite direction (rivet from outside 
to inside STA1815 honeycomb). 
42. With reference to Figure 42 thru Figure 47, put in position the new angle  
P/N 109-0952-67-111, the new butt strap P/N 109-0952-67-113, the web  
P/N 109-0952-67-109 and the doubler P/N 109G5330R01-205. Install by means of 
adhesive EA9309.3NA. Starting from the forward side of the post, install the rivets. Seal 
edges by means of sealant PROSEAL 890B2 or MC780 B-2. 
43. With reference to Figure 42 thru Figure 44, install the external butt-strap  
P/N 109-0952-67-115 to the post by means of adhesive EA9309.3NA and rivets. Seal 
edges by means of sealant PROSEAL 890B2 or MC780 B-2. 
NOTE 
Perform the following Steps from 44 to 50 ONLY if the 
angle P/N 109-0320-96-74 (or P/N 109-0320-96-508) is 
undamaged. 
44. With reference to Figure 41 and Figure 42, remov e the four rivets that attach the two

### Page 57

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 56 of 108 REVISION: B - August 24, 2023 
nut-plates to the forward side of the post. Discard the two nut-plates. 
45. With reference to Figure 42 thru Figure 44, put the web P/N 109-0952-67-109 the doubler 
P/N 109G5330R01-206 in position on interior of the post. 
NOTE 
When marking the position of the rivet holes, make sure 
that the distance between the hole centre and the edge 
of the sheet is at least 2.5 times the diameter of the rivet. 
46. Drill the holes to attach the web P/N 109-0952-6 7-109 and the doubler  
P/N 109G5330R01-206 to forward and aft bulkhead P/N 109-0320-96. Attach the parts in 
position with Cleco fasteners. 
47. With reference to Figure 42, put the external butt-strap  
P/N 109-0952-67-115 in position. If necessary, adapt the shape to the profile of the post 
to allow the correct installation. Mark and drill the attachment holes. 
48. Remove the paint from the existing web P/N 109-0320-96-72 (or P/N 109-0320-96-506) 
and from the new web P/N 109-0952-67-109 in the area of installation of the external butt-
strap P/N 109-0952-67-115. 
NOTE 
For accessibility reason, it is allowed to install rivets P/N 
A879A05L150 on opposite direction (rivet from outside 
to inside STA1815 honeycomb). 
49. With reference to Figure 42 thru Figure 44, put in position the web  
P/N 109-0952-67-109 and the doubler P/N 109G5330R01-205. Install by means of 
adhesive EA9309.3NA. Starting from the forward side of the post, install the rivets. Seal 
edges by means of sealant PROSEAL 890B2 or MC780 B-2. 
50. With reference to Figure 42 thru Figure 44, install the external butt-strap  
P/N 109-0952-67-115 to the post by means of adhesive EA9309.3NA and rivets. Seal 
edges by means of sealant PROSEAL 890B2 or MC780 B-2. 
51. With reference to Figure 32, reinstall and bond with EA9309.3NA all the shims that were 
installed under the lower end of forward RH bulkhead P/N 109-0320-96.

### Page 58

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 57 of 108 
NOTE 
Make sure that the rivets in the zone of installation of the 
torque tube support P/N 109-0011-18-1 have the 
countersunk head on both sides. Make sure that the 
head does not protrude over the surface. Flush the 
heads if necessary. 
NOTE 
Reuse the removed part if it is not damaged. 
52. With reference to Figure 38, Figure 39 and Figur e 48, put the forward cap  
P/N 109-0320-90-208 in position and bond by means of adhesive EA9309.3NA and 
PROSEAL 890B2. Install the forward cap by means of the indicated rivets. Seal the edges 
of the forward LH cap by means of sealant PROSEAL 890B2 or MC780 B-2. 
53. With reference to Figure 41 and 42, install the two nutplates MS21071L08 in the indicated 
position by means of the rivets. 
54. Temporarily put the RH post lower fairing P/N 109-0324-30-202 and the RH lower fairing 
P/N 109-0324-25-304 in position and drill the rivet holes in the upper part of the forward 
RH cap P/N 109-0320-90-208. 
55. Touch-up the exposed areas of the repaired zones with primer and paint to restore the 
original aspect. 
56. With reference to Figure 27, bond with PROSEAL 890B2 then attach with rivets the RH 
lower fairing P/N 109-0324-25-304. Make sure that that the drain holes in the fairing are 
not plugged by the sealant. 
57. With reference to Figure 27, bond with PROSEAL 890B2 then attach with rivets the RH 
post lower fairing P/N 109-0324-30-202. Make sure that that the drain holes in the fairing 
are not plugged by the sealant. 
58. In accordance with MM Paragraphs 07-30-1 or 07-30-2, lay down the helicopter. 
59. Reinstall the cockpit/passenger doors caution system switch on the RH post centre fairing 
P/N 109-0324-29-102 using the related screws. Put the shims (if any) in their original 
position. 
60. With reference to Figure 27, reinstall the LH post centre fairing P/N 109-0324-29-102 using 
the related attaching screws. 
61. If originally installed, reinstall the sill-liner or apply the anti-slip paint on the upper side of 
the fairings P/N 109-0324-25-304 and 109-0324-30-202. 
62. Reinstall the cockpit and passenger doors seals. 
63. In accordance with MM Paragraphs 67-00-12 and 67-12-1, reinstall the following 
components of the flight control system:

### Page 59

S.B. N°109EP-173 ALERT 
 DATE: November 10, 2020 
Page 58 of 108 REVISION: B - August 24, 2023 
 Lateral cyclic control rod P/N 109-0032-01-1; 
 Longitudinal cyclic control rod P/N 109-0032-03-1; 
 Lateral cyclic lever P/N 109-0020-17-1; 
 Lateral cyclic control rod P/N 109-0032-02-1. 
64. In accordance with MM Paragraph 21-21-1, reinstall the air conditioning duct located 
inside the door lower sill. 
65. With reference to Figure 25 and Figure 26, reinstall the lateral cyclic control rod assy and 
the longitudinal cyclic control rod assy P/N 109-0032-07-01 as follows: 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
65.1 Put the longitudinal control rod assy in positi on on interior of the right cabin post by 
inserting it from the top. Observe the correct sense and position of installation, as 
identified in previous Step 2.8. 
65.2 With reference to Figure 26, attach the upper end of the longitudinal control rod to 
the lever using the bolt P/N AN174-12, one washer P/N AN960-PD416 (under the 
bolt head), one washer P/N AN960-PD416 under the nut, and the nut  
P/N MS17825-4. Torque the nut to 3.4 thru 4.5 Nm and install a new cotter pin P/N 
MS24665-153. If necessary, install one additional washer P/N AN960-PD416 
under the nut to obtain the correct engagement of the nut. 
65.3 With reference to Figure 26, attach the lower end of the longitudinal control rod to 
the lever using the bolt P/N AN174-12, one washer P/N AN960-PD416 (under the 
bolt head), one washer P/N AN960-PD416 under the nut, and the nut P/N 
MS17825-4. If required, move slightly cyclic control stick as necessary to allow the 
insertion of the bolt. Torque the nut to 3.4 thru 4.5 Nm and install a new cotter pin 
P/N MS24665-153. If necessary, install one additional washer  
P/N AN960-PD416 under the nut to obtain the correct engagement of the nut. 
CAUTION 
Apply the maximum care to prevent any damage to the 
control rod caused by rubbing with other parts of the 
helicopter. 
65.4 Put the lateral control rod assy in position on  interior of the right cabin post by 
inserting it from the top. Observe the correct sense and position of installation, as 
identified in previous Step 2.8.

### Page 60

S.B. N°109EP-173 ALERT 
DATE: November 10, 2020 
REVISION: B - August 24, 2023 Page 59 of 108 
65.5 With reference to Figure 25, attach the upper end of the lateral control rod to the 
lever using the bolt P/N AN174-12, one washer P/N AN960-PD416 (under the bolt 
head), one washer P/N AN960-PD416 under the nut, and the nut  
P/N MS17825-4. Torque the nut to 3.4 thru 4.5 Nm and install a new cotter pin P/N 
MS24665-153. If necessary, install one additional washer P/N AN960-PD416 
under the nut to obtain the correct engagement of the nut. 
65.6 With reference to Figure 25, attach the lower end of the lateral control rod) to the 
lever using the bolt P/N AN174-12, one washer P/N AN960-PD416 (under the bolt 
head), one washer P/N AN960-PD416 under the nut, and the nut  
P/N MS17825-4. If required, move slightly cyclic control stick as necessary to allow 
the insertion of the bolt. Torque the nut to 3.4 thru 4.5 Nm and install a new cotter 
pin P/N MS24665-153. If necessary, install one additional washer  
P/N AN960-PD416 under the nut to obtain the correct engagement of the nut. 
65.7 Remove the masking tape that has been put on the rods to identify the direction of 
installation (ref. Step 2.8). 
65.8 Perform a duplicate inspection of installation of the control rods. The duplicate 
inspection must include, but is not limited to, correct assembly, security, correct 
application of cotter pins, thread engagement and protrusion, and a functional 
check for complete range, freedom of movement and operation in correct sense. 
66. To check that the Fixed Flight Component have been properly re-installed, get access to 
the cyclic control stick on the left side of the cockpit, and with hydraulic power supply at 
1500 PSI perform the following Step of MM Paragraph 67-00-26, (ref. Figures 3 thru 10): 
 Disengage the spring P/N 109-0020-36 from the bracket; 
 Fully loosen the friction control; 
 Step B; 
 Step C. If rigging pins do not fit, apply MM Paragraph 67-00-26; 
 Engage the spring P/N 109-0020-36 on bracket; 
 Step H; 
 Do the adjustment of the fixed frictions of the cyclic control system. 
67. Perform an operational test of the cyclic control system to make sure that the control 
linkages move freely. 
68. Reinstall all the access panels you have removed to perform the repair. 
69. Panel P/N 109-0320-90-8, removed at Step 7, can be reused after removing thoroughly 
any trace of sealant using a plastic scraper and a cloth moistened with solvent  
MIL-PRF-680 TY II. 
70. Reinstall the support panels located under the pilot and co-pilot seat. Reinstall also the

The text continues at https://openairdocs.org/service-documents/leonardo/109ep-173/file/40dc918516e4.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
