# Leonardo Alert Service Bulletin 109EP-177: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2023-1894, the docket of AD 2023-25-08. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 109EP-177](https://openairdocs.org/service-documents/leonardo/109ep-177.md)
- Title as filed: Leonardo Helicopters ASB No. 109EP-177 Rev A (reduced size PDF)
- Pages: 54
- PDF: https://openairdocs.org/files/sha256/81/bd/81bdcffe23921e7e1e4bfb5649be8cf1678b62167c4f7ae976d573e04f7c545b
- Page: https://openairdocs.org/service-documents/leonardo/109ep-177/file/81bdcffe2392

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Pa ge 1 of 53 
N°  109EP-177 
DA TE:  January 11, 2022 
REV. :  A - M arch 3, 2022 
TITLE 
ATA 62 – INSPECTION OF MAIN ROTOR SCISSOR CHAIN 
REVISION LOG 
Helicopters which are already complying with previous issue of this Service Bulletin must 
n
ot perform any additional actions. 
Revision A is issued in order to introduce the following changes: 
- added tolerance for Part IV and Part V compliance time; 
- PSE mailbox update; 
- Minor amendments. 
Revision bars identify changes. 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 2 of 53 REVISION: A - March 3, 2022 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
Part I: all A109E helicopters. 
Part II: all A109E helicopters not fulfilling Part I or Part IV or Part V requirements. 
Part III: all A109E helicopters not fulfilling Part I or Part IV or Part V requirements. 
Part IV: all A109E helicopters. 
Part V: all A109E helicopters. 
B. COMPLIANCE 
Part I: Within and not later than 25 FH or 3 months, whichever occurs first, after the 
issue of this Service Bulletin. 
Part II: Every 25 FH until replacement of affected components as per Part III. 
Part III: Within and not later than 400 FH or 2 years, whichever occurs first, after the 
detection of affected parts. 
Part IV: Every 50 FH. A tolerance of 5 FH is allowed. Tolerances are not cumulative. 
Part V: Every 200 FH. A tolerance of 10 FH is allowed. Tolerances are not cumulative. 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin is issued in order to provide the necessary instructions on how to 
perform the inspection of the main rotor scissor bearing P/N NHBY6V204. 
E. DESCRIPTION 
Some cases of excessive axial play have been detected on the ball bearing of the 
lower half of the M/R rotating scissor assy. In few cases, this resulted in the slippage 
of the ball bearing outside its seat without jeopardizing the functionality of the scissor 
assy. These events have been detected on-ground during the required maintenance 
scheduled inspections or Pilot’s Daily Pre-Flight Checks of the rotating scissor for 
condition and security. The investigation on the root cause is still ongoing but 
Leonardo Helicopters decided, as a precautionary measure, to issue this SB to 
perform (Part I) a one-time check to evaluate the correct coupling between the two 
halves of the rotating scissor assy and to check the axial play of the ball bearing  
P/N NHBY6V204. In case non-conformities are detected, instructions are provided to 
keep the axial play under control (Part II) until the replacement of the affected parts

### Page 3

S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 3 of 53 
(Part III). In addition, instructions are provided to perform qualitative (Part IV) and 
quantitative (Part V) evaluations of the axial play of the ball bearing as a regular 
inspection task.  
Revision A of this Service Bulletin is issued to allow a tolerance to the compliance time 
of Part IV and Part V.  
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin, the following MMH are deemed necessary: 
Part I: 2 (two) MMH 
Part II: 1 (one) MMH 
Part III: 4 (four) MMH 
Part IV: 0,30 (half an hour) MMH 
Part V: 1 (one) MMH 
MMH do not consider inspections and/or replacements which depend on inspections 
outcomes. MMH are based on hands-on time and can change with personnel and 
facilities available. 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
1) PUBLICATIONS 
Following Data Modules refer to MM:

### Page 4

S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 4 of 53 REVISION: A - March 3, 2022 
DATA MODULE DESCRIPTION PART 
DM01 00-20-1 Helicopter safety – Pre-operation All 
DM02 06-40-1 Access panels and doors All 
DM03 62-31-15 Rotating scissors, Maintenance 
Practices 
All 
DM04 62-31-16 Rotating scissors, Inspection I, II, IV, V  
DM05 62-31-25A Swashplate and Support, 
Disassembly/Assembly 
III  
DM06 62-21-50 Floating ring, Removal/Installation III 
 
Following Data Modules refer to CR&OP: 
DATA MODULE DESCRIPTION PART 
DM07 3C-A-62-31-03-01C-921A-C Lower lever - Bushings - 
Replacement (remove and install 
a new item) 
III 
DM08 3C-A-62-31-03-01B-921A-C Lower lever - Bushings - 
Replacement (remove and install 
a new item) 
III 
DM09 3C-A-62-31-02-01C-921A-C  Upper lever - Bushings - 
Replacement (remove and install 
a new item) 
III 
DM10 3C-A-62-31-02-01B-921A-C  Upper lever - Bushings - 
Replacement (remove and install 
a new item) 
III 
DM11 3C-A-62-21-08-01A-921A-C Scissors support flange - 
Bushings - Replacement (remove 
and install a new item) 
III 
2) ACRONYMS & ABBREVIATIONS 
AMDI Aircraft Material Data Information 
MM Maintenance Manual 
CR&OP Component Repair and Overhaul Publication 
DM Data Module 
DOA Design Organization Approval 
EASA European Aviation Safety Agency 
LH Leonardo Helicopters 
MMH Maintenance Man Hours 
P/N Part Number 
3) ANNEX 
ANNEX A – M/R rotating scissor force check 
ANNEX B – M/R rotating scissor dimensional check

### Page 5

S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 5 of 53 
ANNEX C – M/R rotating scissor axial play check on board the helicopter 
ANNEX D – M/R rotating scissor axial play check on ground 
ANNEX E – Detailed compliance form 
J. PUBLICATIONS AFFECTED 
A109E-MM Maintenance Manual A109E Helicopter Model. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 6

S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 6 of 53 REVISION: A - March 3, 2022 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
PART I 
# P/N  ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
1 MS24665-283 MS24665-285 Pin, cotter 1 . (1) - 
2 MS24665-302  Pin, cotter 1 . (1) - 
PART II 
N.A. 
PART III 
N.A. 
PART IV 
N.A. 
PART V 
N.A. 
Refer also to IPC for the spare parts required to comply with the MM 
Paragraphs/CR&OP DM referenced in the accomplishment instructions. 
2) CONSUMABLES 
 
Refer to AMDI for the consumable materials required to comply with the MM/CR&OP 
DM referenced in the accomplishment instructions. 
3) LOGISTIC MATRIX 
N.A. 
NOTE 
(1) Item to be procured as local supply. 
B. SPECIAL TOOLS 
The following special tools, or equivalent, are necessary to accomplish this Service 
Bulletin: 
# P/N DESCRIPTION Q.TY NOTE PART 
3 Commercial Dynamometer 1 (B1) I

### Page 7

S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 7 of 53 
# P/N DESCRIPTION Q.TY NOTE PART 
4 Commercial Non-elastic cable 1 (B1) I 
5 Commercial Caliper 1 (B1) I 
6 Commercial or P/N 3G6005G04751 Support arm, dial gauge 1 (B2) I,II,IV,V 
7 Commercial or P/N 1502251 Dial gauge 1 (B2) I,II,IV,V 
8 Commercial or P/N 1500019 Extension dial gauge 1 (B2) I,II,IV,V 
9 Commercial or P/N 3G6005G01531 Support dial gauge (M/R damper hub side) 1 (B2) I,II,IV,V 
Refer also to PTUM for the special tools required to comply with the MM 
Paragraphs/CR&OP DM referenced in the accomplishment instructions. 
Refer also to Annex A for the equipment/tools required for the force check of the main 
rotor rotating scissor. 
Refer also to Annex B for the equipment/tools required for the dimensional check of 
the main rotor rotating scissor. 
Refer also to Annex C for the equipment/tools required for the axial play measurement 
on board the helicopter. 
SPECIAL TOOLS NOTE 
 Tool to be procured as local supply.  
 Equivalent P/N may be locally supplied or manufactured i.a.w. Annex C – Axial 
play measurement on board the helicopter. 
C. INDUSTRY SUPPORT INFORMATION 
Owners/Operators who comply with the instructions of this Service Bulletin no later 
than the applicable date in the “Compliance” section will be eligible to receive 
REQUIRED MATERIALS on free of charge basis, except for Consumable Materials 
and Special Tools. 
NOTE 1: Customers who fail to comply with the instructions in this Service Bulletin 
before the compliance date are not eligible for the aforementioned special policy. 
Please Issue relevant MMIR form to your Warranty Administration Dpt accompanied 
by INSPECTION REPORT and PICTURE of the affected area. 
NOTE 2: The INSPECTION REPORT and PICTURE are mandatory; in case the 
MMIR is not accompanied by these documents, it will be rejected.

### Page 8

S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 8 of 53 REVISION: A - March 3, 2022 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the 
modification area and adequately protect them until 
their later re-use. 
b) Exposed thread surface and nut must be protected 
using a layer of tectyl according to MIL-C-16173 
grade I. 
c) All lengths are in mm. 
d) The items indicated in this Service Bulletin can be 
installed on the helicopter with different P/N. Refer 
to IPD Chapter 62 for the applicable P/N. 
e) The logics of operations and instructions required 
into this SB are explained at high level in the flow 
chart reported in Figure 1. 
PART I 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. M/R rotating scissor coupling inspection 
NOTE 
It is mandatory, in any case, to record all the measures 
collected during the Force Check and, if required, the 
Dimensional Check into the Detailed compliance form 
(Annex E). 
2.1 Perform the upper and lower M/R rotating scissor  lever reference value force 
check as per Annex A step 3. 
2.2 Perform the upper and lower M/R rotating scissor lever maximum torque force 
check as per Annex A step 4.

### Page 9

S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 9 of 53 
NOTE 
Reinstall new cotter-pins and nuts according to the 
applicable AMP DMs. 
 
NOTE 
The completion of the installation of the M/R rotating 
scissor assy is not required if the axial play check at 
step 3 will be performed directly on ground and not on 
board the helicopter. 
2.3 If at least one of the measures at steps 4.1.4 a nd 4.1.6 of Annex A is not within 
acceptable values, perform Dimensional Check as per Annex B and proceed with 
step 2.4, otherwise complete the installation of the M/R scissor assy i.a.w. MM 
Paragraph 62-31-15 and proceed with Step 3. 
2.4 If at least one of the dimensional checks required by Annex B has failed, in 
accordance with MM Paragraph 62-31-15, reinstall the M/R rotating scissor. 
Proceed with Step 3. 
2.5 If all checks as per Annex B are compliant with allowable limits, in accordance 
with MM Paragraph 62-31-15, partially install the M/R scissor assy attaching only 
the upper scissor lever assy to the bracket flange assy. 
2.6 Repeat M/R rotating scissor maximum torque force check as per Annex A step 4. 
If this second application is failed, contact Leonardo Helicopters for instructions.  
2.7 In accordance with MM Paragraph 62-31-15, reinstall the lower scissor lever assy 
on the swashplate retaining bolt. Proceed to Step 3. 
3. M/R rotating scissor axial play check 
NOTE 
It is mandatory, in any case, to record the measures 
collected during the Axial Play Check into the Detailed 
compliance form (Annex E). 
NOTE 
If the ball bearing is found dislodged from its seat, 
record the finding on the Annex E – Detailed 
compliance form and proceed directly with step 4.

### Page 10

S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 10 of 53 REVISION: A - March 3, 2022 
NOTE 
If support arm P/N 3G6005G04751 or equivalent is not 
available or the M/R rotating scissor assy has been 
already removed from the helicopter it is possible to 
perform the axial play check on ground i.a.w. Annex D. 
3.1 In accordance with Annex C or with Annex D, as a pplicable, perform the axial 
play check of the ball bearing P/N NHBY6V204.  
3.2 Record the value measured in Annex E – Detailed compliance form and proceed 
with step 4. 
4. Inspection Outcomes 
4.1 With reference to Figure 1 and to the results of the inspections recorded into the 
detailed compliance form (Annex E), define the applicable actions as required by 
Table 1 and proceed with step 5: 
NOTE 
Colours used in Table 1 recalls the outcomes of 
Scissor Coupling Check and Axial Play inspection as 
detailed in the flow chart reported in Figure 1 and in the 
Detailed Compliance Form: 
- Green: Test passed  
- Yellow: Test failed. 
- Red: Axial Play Check failed (axial play greater than 
0.75mm). Immediate replacement of parts identified 
in Table 1 is required. 
- Grey: Contact Leonardo Helicopters.

### Page 11 (OCR)

LEONARDO
HELICOPTERS
Step 2 - SCISSOR COUPLING CHECK
UNCERTAIN RESULT (2ND
PASSED  FAILED  maximum torque force check
failed)
Consider the helicopter affected by Part Il until
PASSED  Consider the helicopter affected by Part IV  and Part V.  Part Ill and then consider the helicopter  replacement of all affected components as per
affected by Part IV and Part V.
FAILED (axial play  Consider the helicopter affected by Part Il until  Consider the helicopter affected by Part Il until
value between 0.25  replacement of all affected components as per  replacement of all affected components as per
mm and 0.75 mm)  Part Ill and then consider the helicopter  affected by Part IV and Part V.  Part Ill and then consider the helicopter  affected by Part IV and Part V.
Before next flight, replace lower scissor lever
assy as per Part Ill. If the lower scissor lever is
the only component not fulfilling Part I
FAILED (axial play  Before next flight, replace lower scissor lever  dimensional check, consider the helicopter
value greater than  assy as per Part Ill and then consider the  affected by Part IV and Part V, otherwise  Contact Leonardo Helicopters.
0.75 mm)  helicopter affected by Part IV and Part V.  consider the helicopter affected by Part Il until
replacement of all affected components as per
Part Ill and then consider the helicopter
affected by Part IV and Part V.
Before next flight, replace lower scissor lever
assy, retaining bolt and washer as per Part III.
If the lower scissor lever is the only
Before next flight, replace lower scissor lever  component not fulfilling Part I dimensional
FAILED (ball bearing  assy, retaining bolt and washer as per Part III  check, consider the helicopter affected by Part
dislodged)  and then consider the helicopter affected by  IV and Part V, otherwise consider the
Part IV and Part V.  helicopter affected by Part Il until replacement
of all affected components as per Part III and
then consider the helicopter affected by Part
IV and Part V.
Table 1 - Part I inspections - Outcomes assessment
5. With reference to MM Paragraph 06-40-1, reinstall the access panels P17, P18 and P24
on the helicopter.
6. Return the helicopter to flight configuration and record for compliance with Part I of this
Service Bulletin on the helicopter logbook.
NOTE
"XXXXX" in the subject line below is the helicopter S/N.
7. Send the detailed compliance form (Annex E) with Subject line "109EP-177 Rev.A - S/N
XXXXX - Detailed Compliance Form to the following mail box:
engineering.support. hd@leonardo.com
8. Send the attached compliance form to the following mail box:
engineering.support. hd@leonardo.com
As an alternative, gain access to My Communications section on Leonardo WebPortal
and compile the "Service Bulletin Application Communication".
S.B. N°109EP-177 ALERT
DATE: January 11, 2022
REVISION: A - March 3, 2022  Page 11 of 53

### Page 12

S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 12 of 53 REVISION: A - March 3, 2022 
PART II 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. With reference to MM Paragraph 06-40-1, remove the access panels P17, P18 and P24 
from the helicopter. 
NOTE 
If the ball bearing is found dislodged from its seat, 
record the finding and proceed directly with step 4. 
NOTE 
If support arm P/N 3G6005G04751 or equivalent is not 
available or the M/R rotating scissor has been already 
removed from the helicopter it is possible to perform 
axial play check on ground i.a.w. Annex D. 
3. In accordance with Annex C or Annex D, as applica ble, perform the axial play check of the 
ball bearing P/N NHBY6V204. Record the measure acquired.  
4. Accounting for the results of the inspection performed at step 3, perform the actions 
below: 
4.1 If axial play value is between 0.25 mm and 0.75 mm, proceed with step 5. 
NOTE 
If the lower scissor lever is the only component not 
fulfilling Part I requirements, after accomplishment of  
step 4.2 or 4.3, the helicopter has to be considered 
affected by Part IV and Part V. 
4.2 If axial play value is greater than 0.75 mm, rep lace lower scissor lever assy  
P/N 109-0134-25-101 (or P/N 109-0134-10-105 or P/N 109-0134-10-101) as per 
Part III and proceed with step 5. 
4.3 If ball bearing is found dislodged, replace lower scissor lever assy  
P/N 109-0134-25-101 (or P/N 109-0134-10-105 or P/N 109-0134-10-101), 
retaining bolt and washer as per Part III and proceed with step 5. 
5. With reference to MM Paragraph 06-40-1, reinstall the access panels P17, P18 and P24 
on the helicopter.  
6. Return the helicopter to flight configuration and record for compliance with Part II of this 
Service Bulletin on the helicopter logbook. 
7. Send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardo.com

### Page 13

S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 13 of 53 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 14

S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 14 of 53 REVISION: A - March 3, 2022 
PART III 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. With reference to MM Paragraph 06-40-1, remove the access panels P17, P18 and P24 
from the helicopter. 
3. With reference to MM Paragraph 62-31-15, remove the rotating scissor assy from the 
helicopter. 
NOTE 
- If spare components (any of the parts 
reported in Table 2) have to be replaced, they 
can be referred to as serviceable only after 
being positively checked as per Annex B 
(dimensional check) before installation on 
board the helicopter. 
- A complete spare rotating scissor assy can 
be referred to as serviceable if positively tested 
according to Annex A step 4 (force check). 
4. With reference to Table 2 and steps below, replac e the components found outside the 
tolerances defined in Part I (as reported in the Detailed Compliance Form in Annex E) with 
a serviceable part as follows: 
NOTE 
If the nut P/N MS17825-6 is removed, discard the part 
and replace with a new one according to applicable 
DM. 
Description P/N 
F
or replacement,  
refer to step 
Scissor Bracket Flange assy 
109-0111-49-101 
or 
109-0111-11-105 
4.1 
Rotary Scissor Sleeve 
109-0110-69-109 
or 
109-0110-69-105 
4.2 
Rotary Scissor Sleeve 109-0110-69-111 4.3

### Page 15

S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 15 of 53 
or 
109-0110-69-107 
Lower Scissor Lever assy 
109-0134-25-101 
or 
109-0134-10-101 
or 
109-0134-10-105 
4.4 
Upper Scissor Lever assy 
109-0134-23-105 
or 
109-8110-16-1 
4.5 
Table 2 
4.1 For scissor bracket flange assy P/N 109-0111-49-101 (or P/N 109-0111-11-105), 
perform the actions below: 
4.1.1 With reference to MM Paragraph 62-21-50, remove the scissor bracket 
flange assy from the helicopter. 
CAUTION 
Only approved personnel (Leonardo Helicopters 
Facilities, Leonardo Authorized Component Repair 
Centres within the approved capabilities or Customers 
trained by Leonardo Helicopters for specific activities) 
are permitted to perform the bushing replacement 
according to step 4.1.2. 
4.1.2 If all the out of tolerances dimensions can be  restored replacing the 
bushings, with reference to CR&OP DM 3C-A-62-21-08-01A-921A-C, 
perform replacement of bushings and, with reference to MM Paragraph 
62-21-50, reinstall the restored scissor bracket flange assy and 
proceed with step 5. Otherwise proceed with next step. 
4.1.3 With reference to MM Paragraph 62-21-50, discard and replace the 
scissor bracket flange assy. 
4.2 For rotary scissor sleeve P/N 109-0110-69-109 (or P/N 109-0110-69-105), 
perform the actions below: 
4.2.1 With reference to MM Paragraph 62-31-15, discard and replace the 
rotary scissor sleeve and install the rotating scissor assy. 
4.3 For rotary scissor sleeve P/N 109-0110-69-111 (or 109-0110-69-107) 
replacement, perform the actions below:

### Page 16

S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 16 of 53 REVISION: A - March 3, 2022 
4.3.1 With reference to MM Paragraph 62-31-15, disassemble the rotating 
scissor assy. 
4.3.2 With reference to MM Paragraph 62-31-15, discard and replace the 
rotary scissor sleeve and assemble the rotating scissor assy. 
4.4 For lower scissor lever assy P/N 109-0134-25-101 (or 109-0134-10-105 or 109-
0134-10-101), perform the actions below: 
4.4.1 With reference to MM Paragraph 62-31-15, disassemble the rotating 
scissor assy. 
CAUTION 
Only approved personnel (Leonardo Helicopters 
Facilities, Leonardo Authorized Component Repair 
Centres within the approved capabilities or Customers 
trained by Leonardo Helicopters for specific activities) 
are permitted to perform the bushing replacement 
according to step 4.4.2. 
4.4.2 If all the out of tolerances dimensions can be  restored replacing the 
bushings (and the axial play measured at Part I is not greater than 0.25 
mm) with reference to CR&OP DM 3C-A-62-31-03-01C-921A-C for P/N 
109-0134-25-101 (CR&OP DM 3C-A-62-31-03-01B-921A-C for  
P/N 109-0134-10-105 or P/N 109-0134-10-101), perform replacement 
of bushings and, with reference to MM Paragraph 62-31-15, assemble 
the rotating scissor assy and proceed with step 5. Otherwise proceed 
with next step. 
4.4.3 With reference to MM Paragraph 62-31-15, discard and replace the 
lower scissor lever assy and reassemble the rotating scissor assy. 
NOTE 
If the bearing ball has been found out of its seat, 
perform steps 4.4.4 and 4.4.5. 
4.4.4 Discard and replace the washer P/N 109-0130-49 -1. 
4.4.5 With reference to MM Paragraph 62-31-25A, discard and replace the 
retaining bolt P/N NAS1306-28D. 
4.5 For upper scissor lever assy P/N 109-0134-23-105 (or P/N 109-8110-16-1) 
replacement, perform the actions below: 
4.5.1 With reference to MM Paragraph 62-31-15, disassemble the rotating 
scissor assy.

### Page 17

S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 17 of 53 
CAUTION 
Only approved personnel (Leonardo Helicopters 
Facilities, Leonardo Authorized Component Repair 
Centres within the approved capabilities or Customers 
trained by Leonardo Helicopters for specific activities) 
are permitted to perform the bushing replacement 
according to step 4.5.2 
4.5.2 If all the out of tolerances dimensions can be  restored replacing the 
bushings, with reference to CR&OP DM 3C-A-62-31-02-01C-921A-C 
for P/N 109-0134-23-105 (CR&OP DM 3C-A-62-31-02-01B-921A-C for 
P/N 109-8110-16-1), perform replacement of bushings and, with 
reference to MM Paragraph 62-31-15, assemble the rotating scissor 
assy and proceed with step 5. Otherwise proceed with next step. 
4.5.3 With reference to MM Paragraph 62-31-15, discard and replace the 
upper scissor lever assy and reassemble the rotating scissor assy. 
5. Perform the maximum torque force check as per Annex A step 4. If at least one of the 
measures at steps 4.1.4 and 4.1.6 of Annex A is not within acceptable values, contact 
Leonardo Helicopters for instructions, otherwise proceed with next step. 
6. With reference to MM Paragraph 06-40-1, reinstall the access panels P17, P18 and P24 
on the helicopter.  
7. Return the helicopter to flight configuration and record for compliance with Part III of this 
Service Bulletin on the helicopter logbook. 
8. Send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardo.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 18

S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 18 of 53 REVISION: A - March 3, 2022 
PART IV 
NOTE:  
If complying with a 200FH inspection, Part IV is not 
required. Perform only Part V. 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. With reference to MM Paragraph 06-40-1, remove the access panels P17, P18 and P24 
from the helicopter. 
3. In accordance to the steps below, perform the qualitative axial play check of the ball 
bearing P/N NHBY6V204 directly on board the helicopter: 
3.1 Pull and push repetitively the rotating scissor assy along the retaining bolt axis to 
detect possible unusual axial play check. 
3.2 If no unusual play is detected, proceed with step 5, otherwise go to step 3.3.  
3.3 If unusual play is detected, perform a quantitative axial play check as described at 
step 4. 
4. In accordance to the steps below, perform the quantitative axial play check of the ball 
bearing P/N NHBY6V204: 
NOTE 
If support arm P/N 3G6005G04751 or equivalent is not 
available or the M/R rotating scissor assy has been 
already removed from the helicopter it is possible to 
perform axial play check on ground i.a.w. Annex D. 
4.1 In accordance with Annex C or Annex D, as applic able, perform the axial play 
check of the ball bearing P/N NHBY6V204. 
4.2 If the axial play is not greater than 0.25 mm, proceed with step 5 
4.3 If the axial play is between 0.25 mm and 0.75 mm, perform Part II until the 
replacement of affected components as per Part III.  
4.4 If the axial play is greater than 0.75 mm, replace the lower scissor lever assy as 
per Part III and then consider the helicopter affected by Part IV and Part V. 
5. With reference to MM Paragraph 06-40-1, reinstall the access panels P17, P18 and P24 
on the helicopter.  
6. Return the helicopter to flight configuration and record for compliance with Part IV of this 
Service Bulletin on the helicopter logbook. 
7. Send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardo.com

### Page 19

S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 19 of 53 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 20

S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 20 of 53 REVISION: A - March 3, 2022 
PART V 
NOTE:  
If complying with a 200FH inspection, Part IV is not 
required. Perform only Part V. 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. With reference to MM Paragraph 06-40-1, remove the access panels P17, P18 and P24 
from the helicopter. 
3. In accordance to the steps below, perform the quantitative axial play check of the ball 
bearing P/N NHBY6V204: 
NOTE 
If support arm P/N 3G6005G04751 or equivalent is not 
available or the M/R rotating scissor assy has been 
already removed from the helicopter it is possible to 
perform axial play check on ground i.a.w. Annex D. 
3.1 In accordance with Annex C or Annex D, as applic able, perform the axial play 
check of the ball bearing P/N NHBY6V204. 
3.2 If the axial play is not greater than 0.25 mm, proceed with step 4 
3.3 If the axial play is between 0.25 mm and 0.75 mm, perform Part II until the 
replacement of affected components as per Part III.  
3.4 If the axial play is greater than 0.75 mm, replace the lower scissor lever assy as 
per Part III and then consider the helicopter affected by Part IV and Part V. 
4. With reference to MM Paragraph 06-40-1, reinstall the access panels P17, P18 and P24 
on the helicopter.  
5. Return the helicopter to flight configuration and record for compliance with Part V of this 
Service Bulletin on the helicopter logbook. 
6. Send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardo.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”. 
 
 
 
 
  
Non cancellare mai questo segnalibro Non cancellare mai interruzione sezione 

### Page 21 (OCR)

LEONARDO
HELICOPTERS
PART IV  Qualitative Axial Play  Check each 50 FH  PART V  Quantitative Axial Play  Check each 200 FH  PART IV  PASSED  Y/N  PART I!  Quantitative Axial Play  Check.  Each 25 FH  PART III  Replacement of affected  parts within 400FH / 2Y
PARTI  STEP 4  Scissor  Axial Play  Coupling  Check  Check  PASSED  PASSED  PASSED  FAILED  FAILED  PASSED  FAILED  FAILED  FAILED  PASSED  FAILED  FAILED  IMMEDIATE  REPLACEAELE DENS  IMMEDIATE  REPLACEMENT OF NON  SERVICEABLE PARTS
PASSED  FAILED  PASSED  FAILED  FAILED
CONTACT LHD  2° FORCE  CHECK  PASSED Y/N
DIMENSIONAL  CHECK  PASSED Y/N  CHECK  < 0.75 mm
SCISSOR  COUPLING  CHECK  STEP 2  AXIAL PLAY  CHECK  STEP 3
Figure 1
S.B. N°109EP-177 ALERT
DATE: January 11, 2022
REVISION: A - March 3, 2022  Page 21 of 53

### Page 22

ANNEX A 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 22 of 53 REVISION: A - March 3, 2022 
ANNEX A 
M/R ROTATING SCISSOR FORCE CHECK

### Page 23

ANNEX A 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 23 of 53 
1 PURPOSE AND APPLICABILITY 
This procedure details the instructions to perform the force check of the M/R rotating 
scissor assy. 
2 EQUIPMENT AND MATERIALS 
The following materials, equipment and tools are requested. 
2.1 MATERIALS 
N.A. 
2.2 EQUIPMENT/TOOLS 
a. Dynamometer  
b. Non-elastic cable  
3 REFERENCE FORCE CHECK INSTRUCTION 
3.1 With reference to MM Paragraph  06-40-1, remove the access panels P17, P18 
and P24 from the helicopter. 
3.2 With reference to Figures A1 and A2, using a dynamometer, perform the reference 
force check of the rotating scissor assy as follows: 
3.2.1 With reference to MM paragraph 62-31-15, detach the lower scissor lever 
assy from the retaining bolt. Discard the nut P/N MS17825-6. 
NOTE 
For better accessibility to the interested area, pull down 
the collective control lever. 
NOTE 
To perform the measure described at step 3.2.2 and 
3.2.4, use a non-elastic cable. 
3.2.2 With reference to Figure A1, with upper scisso r lever in horizontal position 
and lower scissor lever in vertical position, using a suitable cable installed 
on the fulcrum point of the rotating scissor assy, measure the force along 
the vertical direction needed to lift the rotating scissor assy.  
3.2.3 Record the measure in Annex E - Detailed compliance form.  
3.2.4 With reference to Figure A2, using a suitable cable installed on the lower 
part of the lower scissor lever, keeping fixed in position the upper scissor 
lever in horizontal position, measure the force needed for the relative 
rotation between the lower scissor lever and the upper scissor lever.  
3.2.5 Record the measure in Annex E - Detailed compliance form.

### Page 24

ANNEX A 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 24 of 53 REVISION: A - March 3, 2022 
4 MAXIMUM TORQUE FORCE CHECK INSTRUCTION 
NOTE 
The check at step 4.1 must be performed with 
components properly cleaned by dust, sand, excess of 
lubricating grease and corrosion protecting compound 
from the affected fittings. No removal or disassembly is 
required. 
4.1 With reference to Figure A1 and A2, using a dyna mometer, perform the maximum 
torque force check as follows: 
4.1.1 If not already performed, with reference to MM Paragraph 62-31-15, detach 
the lower scissor lever assy from the retaining bolt. Discard the nut P/N 
MS17825-6. 
NOTE 
For better accessibility to the interested area, pull down 
the collective control lever. 
NOTE 
Remove from the bevels of the upper scissor lever any 
primer and print burrs in the area of coupling between 
the upper scissor and lower scissor levers. 
4.1.2 Remove and discard the cotter pin P/N MS24665- 283 or MS24665-285 that 
attaches the upper scissor lever to the lower scissor lever and torque the 
nut P/N MS17825-6 to the torque of 10.0 N∙m. 
NOTE 
Remove from the bevels of the flange any primer and 
print burrs in the area of coupling between the upper 
scissor lever and scissor bracket flange. 
4.1.3 Remove and discard the cotter pin P/N MS24665- 302 that attaches the 
upper scissor lever to the scissor bracket flange and torque the nut  
P/N MS17825-6 to the torque of 10.0 N∙m. 
NOTE 
To perform the measure described at step 4.1.4 and 
4.1.6, use a non-elastic cable. 
4.1.4 With reference to Figure A1, with upper scisso r lever in horizontal position 
and lower scissor lever in vertical position, using a suitable cable installed

### Page 25

ANNEX A 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 25 of 53 
on the fulcrum point of the rotating scissor assy, measure the force along 
the vertical direction needed to lift the rotating scissor assy.  
4.1.5 Record the measure in Annex E - Detailed compliance form. The maximum 
acceptable value is 6.7 N. 
4.1.6 With reference to Figure A2, using a suitable cable installed on the lower 
part of the lower scissor lever, keeping fixed in position the upper scissor 
lever in horizontal position, measure the force needed for the relative 
rotation between the lower scissor lever and the upper scissor lever.  
4.1.7 Record the measure in Annex E - Detailed compliance form. The maximum 
acceptable value is 3.1 N.

### Page 26 (OCR)

K LEONARDO
ANNEX A  HELICOPTERS
FORCE  PIRECTION
UPPER HALF IN
HORIZONTAL
POSITION
LOWER HALF IN
VERTICAL POSITION
For reference only: the scissor in the picture could not be fully representative of the item
actually installed on the aircraft
Figure A1
S.B. N°109EP-177 ALERT
DATE: January 11, 2022
Page 26 of 53  REVISION: А - March 3, 2022

### Page 27

ANNEX A 
Figure A2 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 27 of 53 
 
 
 
 
 
 
 
 
For reference only: the scissor in the picture could not be fully representative of the item 
actually installed on the aircraft

### Page 28

ANNEX B 
 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 28 of 53 REVISION: A - March 3, 2022 
ANNEX B 
M/R ROTATING SCISSOR DIMENSIONAL CHECK

### Page 29

ANNEX B 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 29 of 53 
  
1 PURPOSE AND APPLICABILITY 
This procedure details the instructions to perform the dimensional check of the M/R 
rotating scissor. 
2 EQUIPMENT AND MATERIALS 
The following materials, equipment and tools are requested. 
2.1 MATERIALS 
N.A. 
2.2 EQUIPMENT/TOOLS 
a. Calliper  
3 DIMENSIONAL CHECK INSTRUCTION 
3.1 With reference to MM Paragraph 62-31-15, remove the M/R rotating scissor assy 
from the helicopter. Discard the nut P/N MS17825-6 that attaches the upper 
scissor lever to the scissor bracket flange. 
3.2 With reference to MM Paragraph 62-31-15, disassemble the M/R rotating scissor 
assy. Discard the nut P/N MS17825-6. 
3.3 With reference to Figures B1 thru B4, using a calliper, perform the dimensional 
check of the components described as follows: 
NOTE 
If the helicopter installs the rotating scissor assy  
P/N 109-0134-21-103 perform steps 3.3.1 thru 3.3.8 
and then proceed with step 3.3.16. 
If the helicopter installs the rotating scissor assy  
P/N 109-0134-09-101 perform steps 3.3.9 thru 3.3.15. 
3.3.1 With reference to Figure B1 Section B-B, measu re the dimension “a” in four 
different positions, spaced 90 degrees apart. Allowable values are  
a = 63.15÷63.20 mm. Record the measured values in Annex E - Detailed 
compliance form. 
3.3.2 With reference to Figure B2 Section B-B, measure the dimension “b” in four 
different positions, spaced 90 degrees apart. Allowable values are  
b = 59.15÷59.20 mm. Record the measured values in Annex E - Detailed 
compliance form.

### Page 30

ANNEX B 
 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 30 of 53 REVISION: A - March 3, 2022 
3.3.3  With reference to Figure B2 Section B-B, measure the dimension “c” in 
four different positions, spaced 90 degrees apart. Allowable values are  
c = 63.20÷63.25 mm. Record the measured values in Annex E - Detailed 
compliance form. 
3.3.4 With reference to Figure B2 Section B-B, measure the dimension “d” in four 
different positions, spaced 90 degrees apart. Allowable values are  
d = 86.95÷87.285 mm. Record the measured values in Annex E - Detailed 
compliance form. 
3.3.5 With reference to Figure B3 Section A-A, measure the dimension “e” in four 
different positions, spaced 90 degrees apart. Allowable values are  
e = 74.10÷74.15 mm. Record the measured values in Annex E - Detailed 
compliance form. 
3.3.6 With reference to Figure B3 Section A-A, measure the dimension “f” in four 
different positions, spaced 90 degrees apart. Allowable values are  
f = 87.20÷87.25 mm. Record the measured values in Annex E - Detailed 
compliance form. 
3.3.7 With reference to Figure B4 Detail A, measure the dimension “g” in four 
different positions, spaced 90 degrees apart. Allowable values are  
g = 59.20÷59.25 mm. Record the measured values in Annex E - Detailed 
compliance form. 
3.3.8 With reference to Figure B4 Detail A, measure the dimension “h” in four 
different positions, spaced 90 degrees apart. Allowable values are  
h = 74.00÷74.185 mm. Record the measured values in Annex E - Detailed 
compliance form. 
3.3.9 With reference to Figure B5, measure the dimension “i” in four different 
positions, spaced 90 degrees apart. Allowable values are i = 74.95÷75.285 
mm. Record the measured values in Annex E - Detailed compliance form. 
3.3.10 With reference to Figure B5, measure the dimension “j” in four different 
positions, spaced 90 degrees apart. Allowable values are j = 51.20÷51.25 
mm. Record the measured values in Annex E - Detailed compliance form. 
3.3.11 With reference to Figure B6, measure the dimension “k” in four different 
positions, spaced 90 degrees apart. Allowable values are k = 51.15 
mm÷51.20 mm. Record the measured values in Annex E - Detailed 
compliance form. 
3.3.12  With reference to Figure B7 Section A-A, measure the dimension “l” in four 
different positions, spaced 90 degrees apart. Allowable values are

### Page 31

ANNEX B 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 31 of 53 
l = 66.10 mm÷66.15 mm. Record the measured values in Annex E - 
Detailed compliance form. 
3.3.13 With reference to Figure B7 Section B-B, measure the dimension “m” in 
four different positions, spaced 90 degrees apart. Allowable values are  
m = 75.20÷75.25 mm. Record the measured values in Annex E - Detailed 
compliance form. 
3.3.14 With reference to Figure B8 Detail A, measure the dimension “n” in four 
different positions, spaced 90 degrees apart. Allowable values are  
n = 51.20÷51.25 mm. Record the measured values in Annex E - Detailed 
compliance form. 
3.3.15 With reference to Figure B8 Detail A, measure the dimension “o” in four 
different positions, spaced 90 degrees apart. Allowable values are  
o = 66.00÷66.10 mm. Record the measured values in Annex E - Detailed 
compliance form. 
NOTE 
Reinstall new cotter-pins and nuts according to the 
applicable AMP DMs. 
3.3.16 With reference to MM Paragraph 62-31-15 reass emble M/R rotating scissor 
assy.

### Page 32

ANNEX B 
Figure B1 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 32 of 53 REVISION: A - March 3, 2022 
 
  
a = 63.15 ÷ 63.20
ISO VIEW
SECTION B-B
B
B
VIEW A
A
Lower Scissor Lever Assy

### Page 33

ANNEX B 
Figure B2 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 33 of 53 
 
 
 
b = 59.15 ÷ 59.20 
ISO VIEW
SECTION B-B 
B
B
VIEW A
A
c = ÷ 63.20 63.25 
d = ÷  86.95 87.285
Upper Scissor Lever Assy

### Page 34

ANNEX B 
Figure B3 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 34 of 53 REVISION: A - March 3, 2022 
 
 
e = 74.10 ÷ 74.15
SECTION A-A
A
A
SIDE VIEW
f = 87.20 ÷ 87.25
SECTION B-B
B
B
SIDE VIEW
Rotary Scissor Sleeve

### Page 35

ANNEX B 
Figure B4 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 35 of 53 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
T O P VIEW 
g = 5 .20 ÷ 59 .259
D
ETAIL A 
DETAIL A 
h = 74.00 ÷ 74.185 
ISO VIEW
Scissor Bracket Flange Assy

### Page 36

ANNEX B 
Figure B5 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 36 of 53 REVISION: A - March 3, 2022 
 
 
 
j = ÷  51.25 51.20
i
 = 74.95 ÷ 75.285 
Lower Scissor Lever Assy

### Page 37

ANNEX B 
Figure B6 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 37 of 53 
 
 
k 51.15 ÷ 51.20=
Upper Scissor Lever Assy

### Page 38

ANNEX B 
Figure B7 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 38 of 53 REVISION: A - March 3, 2022 
 
 
l = 66.10 ÷ 66.15
A
A
m = 75.20 ÷ 75.25
B
B
SECTION A-A
SIDE VIEW
SECTION B-B
SIDE VIEW
Rotary Scissor Sleeve

### Page 39

ANNEX B 
Figure B8 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 39 of 53 
 
TOP VIEW
n = 51.20 ÷ 51.25
DETAIL A
DETAIL A
o = 66.00 ÷ 66.10
Scissor Bracket Flange Assy

### Page 40

ANNEX C 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 40 of 53 REVISION: A - March 3, 2022 
 
ANNEX C 
M/R ROTATING SCISSOR AXIAL PLAY CHECK ON BOARD THE 
HELICOPTER

### Page 41

ANNEX C 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 41 of 53 
1 PURPOSE AND APPLICABILITY 
This procedure details the instructions to perform the axial play check of the ball 
bearing P/N NHBY6V204 directly on board the helicopter.  
2 EQUIPMENT AND MATERIALS 
The following materials, equipment and tools are requested. 
2.1 MATERIALS 
N.A. 
2.2 EQUIPMENT/TOOLS 
a.   Support Arm, Dial Gauge 
b.   Dial Gauge 
c. Extension Dial Gauge 
d. Support Dial Gauge  
3 AXIAL PLAY CHECK INSTRUCTION 
NOTE 
An axial play greater than 0.25 mm is considered  
 temporary acceptable following inspection 
requirements detailed in Part II of this Service Bulletin. 
3.1 Install the support arm dial gauge P/N 3G6005G04 751 or equivalent (Figure C1 for 
reference) on the dial gauge P/N 1502251, provided of the extension dial gauge 
P/N 1500019. 
3.2 Install the support arm with the dial gauge on the support dial gauge P/N 
3G6005G01531 or equivalent (Figure C1 for reference). 
3.3 As showed in the red box in Figure C2, install the support dial gauge in its position 
on the pitch control lever. 
3.4 As showed in the red box in Figure C3, put the plunger of the dial gauge against 
the lower part of the lower scissor lever, just below the ball bearing. Hold the dial 
gauge in that position on the pitch control lever. 
3.5 Push and pull by hand the lower scissor lever along the bearing axis. 
3.6 The axial play measurement shall be obtained summing the total displacements, 
between pushing and pulling, showed on the dial gauge. 
3.7 An axial play value greater than 0.25 mm is considered not conformant to the 
requirements. 
3.8 Remove the dial gauge and the applicable supports from the pitch control lever.

### Page 42

ANNEX C 
Figure C1 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 42 of 53 REVISION: A - March 3, 2022

### Page 43 (OCR)

K LEONARDO
ANNEX C  HELICOPTERS
For reference only
Figure C2
S.B. N°109EP-177 ALERT
DATE: January 11, 2022
REVISION: A - March 3, 2022  Page 43 of 53

### Page 44 (OCR)

_ LEONARDO
ANNEX C  HELICOPTERS
REMOVE  SIN
For reference only
Figure C3
S.B. N°109EP-177 ALERT
DATE: January 11, 2022
Page 44 of 53  REVISION: A - March 3, 2022

### Page 45

ANNEX D 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 45 of 53 
 
ANNEX D 
M/R ROTATING SCISSOR AXIAL PLAY CHECK ON GROUND

### Page 46

ANNEX D 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 46 of 53 REVISION: A - March 3, 2022 
1 PURPOSE AND APPLICABILITY  
This procedure details the instructions to perform the axial play check of the ball 
bearing P/N NHBY6V204 on ground.  
2 AXIAL PLAY CHECK INSTRUCTION 
NOTE 
An axial play greater than 0.25 mm is considered  
 temporary acceptable following inspection 
requirements detailed in Part II of this Service Bulletin. 
NOTE 
To perform the axial play check as per step 2.2, it is 
required to remove the rotating scissor assy  
from the helicopter. No disassembly required. 
2.1 With reference to MM Paragraph 62-31-15, remove the M/R rotating scissor assy 
from the helicopter. Discard the nut P/N MS17825-6 that attaches the upper 
scissor lever to the flange assy. 
2.2 With reference to MM Paragraph 62-31-16, perform the axial play check of the ball 
bearing P/N NHBY6V204.  
2.3 With reference to MM paragraph 62-31-15, reinstall the rotating scissor assy with 
the new nut.

### Page 47

ANNEX E 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 47 of 53 
 
ANNEX E 
DETAILED COMPLIANCE FORM

### Page 48

ANNEX E 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 48 of 53 REVISION: A - March 3, 2022 
  
Please send to the following address 
LEONARDO S.p.A. 
CUSTOMER SUPPORT & SERVICES - 
ITALY 
PRODUCT SUPPORT ENGINEERING & 
LICENSES DEPT. 
Via Giovanni Agusta, 520 
21017 Cascina Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036 Fax: +39 0331 225988 
DETAILED COMPLIANCE 
FORM DATE 
Number: S.B. N°109EP-177 
Revision: A 
Customer Name and Address: Telephone: 
Fax: 
S.B. Compliance Date: 
Helicopter Model S/N Aircraft 
FH 
Lower Scissor 
Lever Assy FH 
Upper Scissor 
Lever Assy FH  T.S.O. 
      
Lower Scissor Lever Assy P/N S/N 
  
Upper Scissor Lever Assy P/N S/N 
  
Part I 
Part I Step 2 - SCISSOR COUPLING CHECK 
Part I Step 2.1 - REFERENCE VALUE FORCE CHECK (Refer to Annex 
A Step 3) 
STEP RECORDED VALUE  
Annex A, Step 3.2.2 - Upper Scissor 
Lever assy  
P/N 109-0134-23-105 or  
109-8110-16-1

### Page 49

ANNEX E 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 49 of 53 
Annex  A Step 3.2.4 - Lower Scissor 
Lever assy  
P/N 109-0134-25-101 or  
109-0134-10-105 or 109-0134-10-
101 
 
Part I Step 2.2 - MAXIMUM TORQUE FORCE CHECK (Refer to Annex A 
Step 4) 
STEP THRESHOLD RECORDED VALUE   PASSED / FAILED 
Annex A Step 4.1.4 - 
Upper Scissor Lever assy  
P/N 109-0134-23-105 or  
109-8110-16-1 
≤6.7 N   
Annex A Step 4.1.6 - 
Lower Scissor Lever assy  
P/N 109-0134-25-101 or 
109-0134-10-105 or 109-
0134-10-101 
≤3.1 N   
MAXIMUM TORQUE FORCE CHECK PASSED / FAILED (1)  
Part I Step 2.3 - DIMENSIONAL CHECK (2) (Refer to Annex B) 
STEP THRESHOLD RECORDED VALUES PASSED / FAILED 
Annex B Step 3.3.1 - 
Lower Scissor Lever assy  
P/N 109-0134-25-101 
63.15 - 63.20 mm 
 
(3) 
 
 
 
Annex B Step 3.3.2 - 
Upper Scissor Lever assy  
P/N 109-0134-23-105 
59.15 - 59.20 mm 
 
(3) 
 
 
 
Annex B Step 3.3.3 - 
Upper Scissor Lever assy  
P/N 109-0134-23-105 
63.20 - 63.25 mm 
 
(3) 
 
 
 
Annex B Step 3.3.4 - 
Upper Scissor Lever assy  
P/N 109-0134-23-105 
86.95 - 87.285 mm 
 (3)

### Page 50

ANNEX E 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 50 of 53 REVISION: A - March 3, 2022 
 
Annex B Step 3.3.5 - 
Rotary Scissor Sleeve 
P/N 109-0110-69-109 
74.10 - 74.15 mm 
 
(3) 
 
 
 
Annex B Step 3.3.6 - 
Rotary Scissor Sleeve 
P/N 109-0110-69-111 
87.20 - 87.25 mm 
 (3) 
 
 
 
Annex B Step 3.3.7 – 
Scissor Bracket Flange 
assy 
P/N 109-0111-49-101 
59.20 - 59.25 mm 
 (3) 
 
 
 
Annex B Step 3.3.8- 
Scissor Bracket Flange 
assy 
P/N 109-0111-49-101 
74.00 - 74.185 mm 
 (3) 
 
 
 
Annex B Step 3.3.9 - 
Lower Scissor Lever assy  
P/N 109-0134-10-105 or 
109-0134-10-101 
74.95 - 75.285 mm 
 
(3) 
 
 
 
Annex B Step 3.3.10 - 
Lower Scissor Lever assy  
P/N 109-0134-10-105 or 
109-0134-10-101 
51.20 - 51.25 mm 
 
(3) 
 
 
 
Annex B Step 3.3.11 - 
Upper Scissor Lever assy  
P/N 109-8110-16-1 
51.15 - 51.20 mm 
 
(3)

### Page 51

ANNEX E 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 51 of 53 
 
 
Annex B Step 3.3.12 - 
Rotary Scissor Sleeve 
P/N 109-0110-69-105 
66.10 - 66.15 mm 
 
(3) 
 
 
 
Annex B Step 3.3.13 - 
Rotary Scissor Sleeve 
P/N 109-0110-69-107 
75.20 - 75.25 mm 
 
(3) 
 
 
 
Annex B Step 3.3.14 - 
Scissor Bracket Flange 
assy 
P/N 109-0111-11-105 
51.20 - 51.25 mm 
 
(3) 
 
 
 
Annex B Step 3.3.15 - 
Scissor Bracket Flange 
assy 
P/N 109-0111-11-105 
66.00 - 66.10 mm 
 
(3) 
 
 
 
DIMENSIONAL CHECK PASSED / FAILED (4) 
 
Part I Step 2.6 – 2nd MAXIMUM TORQUE FORCE CHECK (Refer to 
Annex A Step 4)  
STEP THRESHOLD RECORDED VALUES PASSED / FAILED 
Annex A Step 4.1.4 - 
Upper Scissor Lever assy  
P/N 109-0134-23-105 or  
109-8110-16-1 
≤6.7 N

### Page 52

ANNEX E 
S.B. N°109EP-177 ALERT 
 DATE: January 11, 2022 
Page 52 of 53 REVISION: A - March 3, 2022 
Annex A Step 4.1.6 - 
Lower Scissor Lever assy  
P/N 109-0134-25-101 or 
109-0134-10-105 or 109-
0134-10-101 
≤3.1 N  
 
2ND MAXIMUM TORQUE FORCE CHECK PASSED / FAILED (1)  
SCISSOR COUPLING CHECK OUTCOME: 
PASSED / FAILED (5) 
 
Part I Step 3 - AXIAL PLAY CHECK (Refer to Annex C or D) 
STEP THRESHOLD RECORDED VALUES PASSED / FAILED 
Annex C Step 3 or Annex 
D Step 2 –  
Ball Bearing 
P/N NHBY6V204 
≤0.25 mm   
AXIAL PLAY CHECK PASSED / FAILED (6) 
 
NOTES 
(1) Maximum Torque Force Check is considered PASSED if the checks 4.1.4 and 4.1.6 in 
Annex A are both PASSED. 
(2) Dimensional Check i.a.w. step 3.3 in Annex B is required only if Maximum Torque Force 
Check i.a.w. step 4.1 in Annex A is FAILED. 
(3) Checks 3.3.1 thru 3.3.15 in Annex B are considered PASSED if all four measures are within 
threshold. 
(4) Dimensional Check is considered PASSED if the checks 3.3.1 thru 3.3.8 (for helicopters 
installing the rotating scissor assy P/N 109-0134-21-103) or 3.3.9 thru 3.3.15 (for helicopters 
installing the rotating scissor assy P/N 109-0134-09-101) in Annex B are all PASSED. If the 
Dimensional Check is PASSED, perform a 2ND Maximum Torque Force Check. 
(5) Scissor Coupling Check is considered PASSED if Maximum Torque Force Check, and 
Dimensional Check (if required), are PASSED (see Table E1) 
(6) Axial Play Check is considered PASSED if the check 3 in Annex C or 2 in Annex D is 
PASSED.

### Page 53

ANNEX E 
S.B. N°109EP-177 ALERT 
DATE: January 11, 2022 
REVISION: A - March 3, 2022 Page 53 of 53 
 
 
SCISSOR COUPLING CHECK OUTCOME REFERENCE TABLE 
MAXIMUM TORQUE 
FORCE CHECK 
DIMENSIONAL 
CHECK 
2ND MAXIMUM 
TORQUE 
FORCE CHECK 
SCISSOR COUPLING 
CHECK OUTCOME 
PASSED N/A N/A PASSED 
FAILED PASSED PASSED PASSED 
FAILED FAILED N/A FAILED 
FAILED PASSED FAILED 
UNCERTAIN RESULT: 
CONTACT LEONARDO 
HELICOPTERS 
Table E1

### Page 54

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
