# Agusta Mandatory Alert Bollettino Tecnico 109K-53: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2011-0823; AD 2011-17-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Agusta Mandatory Alert Bollettino Tecnico 109K-53](https://openairdocs.org/service-documents/leonardo/109k-53.md)
- Title as filed: U.S. DOT/FAA - Agusta Bollettino Tecnico No. 109K-53
- Pages: 9
- PDF: https://openairdocs.org/files/sha256/9e/9b/9e9b05c063f19e2a41e5511e503a8cffd21858a0634d7531a985cd9da464cd48
- Page: https://openairdocs.org/service-documents/leonardo/109k-53/file/9e9b05c063f1

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

TRANSLATION OF 
BOLLETTINO TECNICO
                N°  109K-53 
 
The technical content of this document is approved 
under the authority of DOA nr EASA.21J.005.
                DATE  December 18, 2009 
 
 
                                REV.  ,  
 
 
Compliance with 
this bulletin is: 
 
 
 
 
 
 
                   Page 1 of 7 
 
SUBJECT: INSPECTION OF THE MAIN ROTOR SCISSOR FITTING ASSY  
P/N 109-0110-67 FIXING BOLTS P/N 109-0101-78-5. 
 
REASON: Perform a “one-time” inspection of the subject bolts to verify the presence 
of two washers under the head of each bolt and provide the instructions 
to restore the correct installation. 
 
HELICOPTERS AFFECTED: 
All the main rotor hub assy P/N 109 -0101-01 installed on the Agusta 
A109K2 helicopters or eventually in stock. 
 
COMPLIANCE: 
PART I^: 
Within the next 5 flight hours after the receipt of this Bollettino. 
 
PART II^: 
Within 25 flight hours after the compliance with PART I^ and however 
within and not later than April 30, 2010. 
 
DESCRIPTION: 
A case of fracture of two of the three bolts P/N 109-0101- 78-5 fixing the 
main rotor scissor fitting assy P/N 109-0110- 67 has been reported in 
flight on an A109K2 helicopter. 
The occurrence did not cause harm to the occupants nor damage to the 
helicopter. 
The investigations revealed that the malfunction was caused by incorrect 
information contained in the technical publications. 
This Bollettino is issued in order to provide the necessary instructions to 
perform a “one-time” inspection to verify the correct installation of the 
main rotor scissor fitting assy P/N 109-0110-67, that includes the 
installation of two washers under the head of each bolt  
P/N 109-0101- 78-5 (PART I^) and, if necessary, to restore the design 
  
 
MANDATORY
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
An Company
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331-229111 - Fax: +39 0331-229605/222595
ALERT
ALERT

### Page 2

B.T. 109K-53 
 
 
 
Page 2 of 7 
 
conditions by replacing the bolts P/N 109-0101- 78-5 that were not 
installed following the correct sequence (PART II^).  
 
REQUIRED MANPOWER: 
The following estimated manpower hours are required for compliance 
with this Bollettino: 
PART I^: Negligible; 
PART II^: 3 (three). 
 
WARRANTY: 
The parts required to apply the present Bollettino shall be supplied on a 
free of charge basis by Agusta upon request, except for consumable 
materials. 
Upon application of this Bollettino, Customers are requested to submit to 
Agusta Warranty Administration the Technical Bulletin Compliance form 
attached to this Bulletin duly completed in all its parts. 
 
REQUIRED MATERIALS: 
PART I^: 
N.A. 
 
PART II^: 
The following materials are required for compliance with PART II^ of this 
Bollettino: 
 
P/N    DENOMINATION    Q.TY  
109-0101-78-5 Bolt 3 
NAS1149C0463R Washer 3 
NAS1149C0432R Washer 3 
 
In addition the following consumable materials are necessary: 
 
SPECIFICATION DENOMINATION Q.TY 
MS20995C32  Lockwire A.R. 
MIL-PRF-16173  Corrosion preventive compound A.R. 
GR 1 CL 2  (cod. 999999999000000191) 
 
SPECIAL TOOLS: 
N.A. 
 
WEIGHT AND BALANCE CHANGES:  
N.A. 
 
REFERENCES: 
A109K2 Maintenance Manual.  
 
PUBLICATIONS AFFECTED: 
 A109K2 Maintenance Manual; 
 A109K2 Overhaul Manual.

### Page 3

B.T. 109K-53 
 
 
 
Page 3 of 7 
 
COMPLIANCE INSTRCTIONS: 
PART I^: 
(See figure 1) 
 
1. Prepare the helicopter on ground for a safe maintenance, 
disconnect any power supply. 
 
2. With reference to figure 1, gain access to the main rotor hub and 
verify that under the head of the three fixing bolts  
P/N 109 -0101-78-5 of the main rotor scissor fitting assy  
P/N 109-0110-67 two washers are installed. 
   
2.1 If for each bolt two washers are installed, p erform the step 3. and 
4. 
 
NOTE 
In this case the compliance with PART II^ of 
this Bollettino is not required. 
 
2.2 Even if under the head of only one bolt a single washer is 
installed, perform the PART II^ within the compliance limits of this 
Bollettino.  
 
3. Return the helicopter to a ready to flight condition. 
 
4. Record compliance with PART I^ of this Bollettino in the 
helicopter log book. 
 
 
PART II^: 
(See figures 1 and 2) 
 
1. Prepare the helicopter on ground for a safe maintenance, 
disconnect any power supply. 
 
2. With reference to figures 1 and 2, proceed with the removal of 
three bolts P/N 109-0101-78-5 as follows: 
 
2.1. With reference to the A109K2 Maintenance Manual , unhook the 
four springs  P/N 109 -0101-56 and the four springs  
P/N 109-0101-57 from the half cover assy P/N 109-0101-98. 
 
2.2. With reference to the A109K2 Maintenance Manual , disconnect 
the rotating half scissor assy P/N 109 -8110-16 from the main 
rotor scissor fitting assy P/N 109-0110-67.

### Page 4

B.T. 109K-53 
 
 
 
Page 4 of 7 
 
NOTE 
To remove the sleeve inside the rotating 
half scissor assy P/N 109-8110-16, use a 
suitable aluminum drift. 
 
2.3. Cut the lockwire and remove the three bolts  
P/N 109-0101-78-5 with the relevant washers, and the main rotor 
scissor fitting assy P/N 109-0110-67. 
 
2.4. Cut the lockwire and remove the two bolts 
P/N 109-0101-78-3 with the relevant washers , the spring holder 
bracket P/N 109-0104-13 and the half cover assy  
P/N 109-0101-98. 
 
3. With reference to figures 1 and 2, proceed with the reassembly of 
the parts previously removed from the main rotor hub as follows: 
 
NOTE 
Apply a light coat of corrosion preventive 
compound MIL-PRF-16173 on the mating 
surfaces and on the bolts unthreaded stem. 
 
3.1. Reinstall the half cover assy P/N 109-0101-98 and the main rotor 
scissor fitting assy P/N 109-0110-67 by means of three new bolts 
P/N 109-0101- 78-5, three new washers NAS1149C0463R 
(nominal thickness 1.5 mm) and three new washers 
NAS1149C0432R (nominal thickness 0.8 mm) under the bolts 
head (ref. figure 1). 
 
3.2. Reinstall the spring holder bracket P/N 109-0104-13 by means of 
the previously removed two bolts P/N 109-0101- 78-3 with two 
washers AN960C416 or NAS1149C0463R and two washers 
AN960C416L or NAS1149C0432R under the bolts head (ref. 
figure 1). 
 
3.3. Torque 7.8 to 9.8 Nm the three bolts P/N 109- 0101-78-5 and the 
two bolts P/N 109-0101- 78-3 and secure them with lockwire 
MS20995C32. 
 
NOTE 
Apply a light coat of corrosion preventive 
compound MIL-PRF-16173 on the head of 
the installed bolts and on the washers. 
 
3.4. With reference to the A109K2 Maintenance Manual, reconnect 
the rotating half scissor assy P/N 109- 8110-16 to the main rotor 
scissor fitting assy P/N 109-0110-67.

### Page 5

B.T. 109K-53 
 
 
 
Page 5 of 7 
 
3.5. With reference to the A109K2 Maintenance Manual , connect the 
four springs  P/N 109 -0101-56 and the four springs  
P/N 109-0101-57 to the half cover assy P/N 109-0101-98. 
 
4. Return the helicopter to a ready to flight condition. 
 
5. Record compliance with PART II^ of this Bollettino in the 
helicopter log book.

### Page 6 (OCR)

B.T. 109K-53
109-0101-98
HALF COVER ASSY
109-0101-57
SPRING
109-0110-67
M.R. SCISSOR FITTING ASSY
NAS1149C0463R WASHER (3 OFF)
NAS1149C0432R WASHER (3 OFF)
109-0101-56
109-0101-78-5 BOLT (3 OFF)  SPRING
109-0104-13 SPRING HOLDER BRACKET
AN960C416 WASHER  109-0101-78-3 BOLT (2 OFF)
OR:
NAS1149C0463R WASHER (2 OFF)  AN960C416L WASHER
OR:
NAS1149C0432R WASHER (2 OFF)
FIGURE 1
Page 6 of 7

### Page 7 (OCR)

B.T. 109K-53
109-8110-16
ROTATING HALF
SCISSOR ASSY
FIGURE 2
Page 7 of 7

### Page 8

(No text on this page.)

### Page 9

Note: 
Remarks: 
Informazioni: 
Information: 
 
Al fine di gestire le varianti alla configurazione base, in relazione all’emissione del Bollettino Tecnico, preghiamo di voler compilare il presen-
te modulo in tutte le sue parti e spedirlo all’indirizzo sopra indicato. Si ringrazia per la gentile collaborazione data.  
We request your cooperation in filling this form,  in order to  keep out statistical data relevant to aircraft configuration up- to-date. The form should be filled in all 
its parts and sent to the above address. We thank you beforehand for the information given. 
MODULO APPLICAZIONE BOLLETTINO TECNICO 
TECHNICAL BULLETIN COMPLIANCE FORM 
Data: 
Date: 
Numero: 
Number: 
Revisione: 
Revision: 
Prego spedire a questo indirizzo: 
Please send to the following address: 
 
AGUSTA S.p.A. 
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING DPT.
Via del Gregge, 100 
21015 Lonate Pozzolo (VA) - ITALY 
Tel.: +39 0331 664600 
Fax: +39 0331 664684
Telefono: 
Telephone: 
Fax: 
Data Applicazione B.T.: 
B.T. Compliance Date: 
Denominazione Cliente ed Indirizzo: 
Customer Name and Address: 
Modello Elicottero 
Helicopter Model S/N Matricola Tail Number Ore Totali Total Hours Ore D.U.R. T.S.O.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
