# Agusta Bollettino Tecnico 109S-15: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2012-0501; AD 2012-23-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Agusta Bollettino Tecnico 109S-15](https://openairdocs.org/service-documents/leonardo/109s-15.md)
- Title as filed: U.S. DOT/FAA - Agusta Service Information - 2
- Pages: 10
- PDF: https://openairdocs.org/files/sha256/35/4d/354d439254a7cc0ae10d2390c97efd0c666f8c7d8a8f7f0afa980ea822d598ad
- Page: https://openairdocs.org/service-documents/leonardo/109s-15/file/354d439254a7

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ALERT 
 
 
 
 
 
TRANSLATION OF  
BOLLETTINO TECNICO  N°  109S-15 
 
The technical content of this document is approved 
under the authority of DOA nr EASA.21J.005. 
DATE  July 12, 2007 
  
 
 
REV.  xxxxxxx 
 
 Compliance with 
this bollettino is: 
 
 
 
 
 
 
                               ALERT                  Page 1 of 8 
 
SUBJECT:INSPECTION AND REWORK OF THE LOWER SEMICHANNEL 
ASSEMBLIES P/N 109-0642-01-171 OF THE FORWARD FIREWALL. 
 
REASON: Perform an “una tantum” (one time) inspection on the two subject lower 
semi-channel assemblies for the presence of the metallic spacers        
P/N 109-0642-01-195, and if present, perform an inspection on the main 
drive shaft, check the spacers for correct fixation and check the gaskets       
P/N 109-0642-01-169 for correct seating. 
 
HELICOPTERS AFFECTED: 
All the Agusta A109S helicopters up to S/N 22034 included, except for 
the S/Ns 22026 and 22033. 
 
COMPLIANCE: 
Within the next 20 (twenty) flight hours after the receipt of this Bollettino 
and however within and not later than September 30, 2007. 
 
DESCRIPTION: 
Cases of mechanical damage of the main drive shaft                            
P/N 109-0415-06-103 have been reported on some A109 series 
helicopters. 
The resultant investigation identified the reason of the malfunction in the 
missing fixing rivets of the metallic spacers P/N 109-0642-01-195 to the 
lower semichannel assy P/N 109-0642-01-171 of the forward firewall. 
The lack of the rivets has allowed the metallic spacers to rotate and 
come into contact with the main drive shaft. 
Not all the helicopters are equipped with the metallic spacers               
P/N 109-0642-01- 195 on the lower semichannel assy                           
P/N 109-0642-01-171, in that the spacers are installed, if required, to 
guarantee a clearance between the main drive shafts and the 
semichannels.

### Page 2

B.T. 109S-15 
 
 
 
Page 2 of 8 
 
 
Moreover, durin g the investigation, cases of wrong positioning of the 
gaskets P/N 109-0642-01-169 have been reported. 
This Bollettino provides the instructions to perform an “una tantum” (one 
time) inspection on the two lower semichannel for the presence of the 
metallic spacers. 
If installed, it is necessary to perform  an inspection on the main drive 
shaft in the semichannels area for damage, correct fixation of the spacer 
on the semichannels and the gaskets for correct seating. 
 
REQUIRED MANPOWER: 
An estimated 3 (three) manpower hours are required for compliance with 
this Bollettino. 
 
WARRANTY: 
The parts required to apply this Bollettino shall be supplied on a free of 
charge basis, except the consumable materials, by Agusta upon request. 
Customers are requested to inform  Agusta – Warranty Administration – 
by means of the attached Technical Bulletin Compliance Form the 
Bollettino implementation. 
 
REQUIRED MATERIALS: 
The following materials could be required for compliance with this 
Bollettino: 
 
P/N DENOMINATION Q.TY 
MS20427M3-5   
or:     Rivet     4 
MS20426T3-5 
A298A04TW02 Rivet 4 
 
In addition the following consumable materials are necessary: 
 
SPECIFICATION DENOMINATION Q.TY 
199-05-107  Adhesive EC776 A.R. 
Type II Class 5   (cod. 500204274) 
TT-M-261 Methylethylketone A.R. 
     (cod. 505407211)     
 
SPECIAL TOOLS:  
N.A. 
 
WEIGHT AND BALANCE CHANGES:  
N.A. 
 
REFERENCES: 
A109S Air Vehicle Maintenance Publication.

### Page 3

B.T. 109S-15 
 
 
 
Page 3 of 8 
 
 
PUBLICATIONS AFFECTED:  
A109S Air Vehicle Maintenance Publication. 
 
COMPLIANCE INSTRUCTIONS: 
 
GENERAL NOTES 
Ø Unless otherwise specified retain all 
parts that will be removed in following 
operations. Replace damaged 
hardware. 
 
Ø After drilling remove all swarf and sharp 
edges and if required restore the 
finishing. 
 
Ø All dimensions are in mm. 
 
(See figures 1 and 2) 
 
1. Prepare the helicopter on ground for a safe maintenance, 
disconnect any power supply. 
 
2. Open the left engine cowling D22 and the right engine cowling 
D28, in accordance with the instructions given in the A109S Air 
Vehicle Maintenance Publication. 
 
NOTE 
The followin g inspection procedure is 
applicable for both lower semichannel 
assemblies P/N 109-0642-01-171, right 
side and left side of the helicopter. 
 
3. With reference to figures 1 and 2, verify if between the lower 
semichannel assy P/N 109-0642-01-171 and the door assy       
P/N 109-0642-01-181 and -182 upper semichannel, the two 
metallic spacers P/N 109-0642-01-195 are installed (semichannel 
left side and right side).  
 
NOTE 
To verify the metallic spacers                  
P/N 109-0642-01-195 presence use a 
mirror and a suitable light source. 
 
3.1 If between the lower semichannel and the upper semichannel  
metallic spacers P/N 109-0642-01-195 are not installed, no 
corrective action is necessary. Perform Step 6 and subsequent of 
this Bollettino.

### Page 4

B.T. 109S-15 
 
 
 
Page 4 of 8 
 
 
3.2 If between the low er semichannel and the upper semichannel  
metallic spacers P/N 109-0642-01-195 are installed, proceed in 
accordance with Step 4 and subsequent of this Bollettino. 
 
4. Perform the inspection on the main drive shaft, the metallic 
spacers for correct fixation on  the semichannels and the gaskets 
for correct seating as follows: 
 
4.1 In accordance with figures 1 and 2, from the forward firewall assy 
P/N 109-0642-01-101,  acting on the relevant fixing hardware, 
remove the lower semichannel assy P/N 109-0642-01-171. 
 
NOTE 1 
To facilitate the lower semichannel assy 
P/N 109-0642-01-171 removal (helicopter 
right side and left side), the removal of the 
left engine cowling D22 and the right engine 
cowling D28, in accordance with the 
instructions given in the A109S Air Vehicl e 
Maintenance Publication is recommended. 
 
NOTE 2 
Take note of the installation position and 
side of the spacers and gaskets on the 
semichannel, in that the parts shall be 
reinstalled in their original position. 
 
4.2 If present, remove the fixing rivets of  the metallic spacers          
P/N 109-0642-01- 195 to the lower semichannel assy                  
P/N 109-0642-01-171. 
 
4.3 From the lower semichannel assy P/N 109 -0642-01-171 remove 
the gaskets P/N 109-0642-01-169 and the metallic spacers        
P/N 109-0642-01-195. 
 
NOTE 1 
During this operation pay particular 
attention to avoid spacers and gaskets 
damage. 
 
NOTE 2 
If two or more stacked gaskets are present, 
they must be retained for reuse. 
 
4.4 Remove the old adhesive from the parts using cheesecloth 
moistened in Methylethylketone.

### Page 5

B.T. 109S-15 
 
 
 
Page 5 of 8 
 
 
4.5 If not present, in accordance with figure 2, perform the two Ø 2,5 
mm holes through the metallic spacers P/N 109-0642-01-195 and 
the lower semichannel assy P/N 109-0642-01-171, taking care not 
to protrude stick out the meta llic spacer towards the inside of the 
semichannel. 
 
NOTE 
If in the metallic spacers the holes are 
present, use them as template to drill the 
lower semichannel. 
 
4.6 In accordance with figure 2, on the lower semichannel assy        
P/N 109-0642-01-171 insta ll the n. 1+1 metallic spacers            
P/N 109-0642-01-195 using two MS20427M3 rivets or two 
MS20426T3 rivets or two rivets P/N A298A04TW02. 
 
CAUTION 
Install the spacers on the semichannel in 
the original position and side, as noted at 
step 4.1. 
 
4.7 In accordance with figure 2, on the n. 1+1 metallic spacers        
P/N 109-0642-01- 195 bond the n. 1+1 gaskets                           
P/N 109-0642-01-169 using adhesive EC776. 
 
CAUTION 
If at step 4.3 stacked gaskets have been 
removed, bond them over the m etallic 
spacers. 
 
4.8 Inspect the main drive shaft tube in the semichannels area for 
damage (nicks and/or scratches). 
 
NOTE 
In case the removal of the main drive shaft 
P/N 109-0415-06-103 shall be necessary 
reinstall the lower semichannel assy         
P/N 109-0642-01-171, before to start with the 
removal operations in accordance with the 
instructions given in the A109S Air Vehicle 
Maintenance Publication. 
 
4.9 In case damages are reported, the main drive shaft shall be 
removed from the helicopter, in accordance with the instructions 
given in the A109S Air Vehicle Maintenance Publication, for the 
damages depth measurement.

### Page 6

B.T. 109S-15 
 
 
 
Page 6 of 8 
 
 
CAUTION 
In case the damages depth is above to the 
value reported in the A109S Air Vehicle 
Maintenance Publication, remove the shaft 
from the service and replace it with one of 
the same P/N. 
 
4.10 If removed, reinstall the main drive shaft on the helicopter, in 
accordance with the instructions given in the A109S Air Vehicle 
Maintenance Publication. 
 
4.11. If not already performed, reinstall the lower semichannel assy P/N 
109-0642-01-171 on the forward firewall assy  P/N 109-0642-01-
101, using the previously removed fixing hardware.  
 
4.12. Using a feeler gauge verify that the minimum clearance around the 
main drive shaft and the upper and low er semichannels is not less 
than 4,0 mm.  
 
CAUTION 
If in one or more places the minimum 
distance should be less than 4,0 mm 
immediately contact the Agusta Customer 
Support. 
 
5. If removed, reinstall the left engine cowling D22 and the right 
engine cowling D28, in accordance with the instructions given in 
the A109S Air Vehicle Maintenance Publication. 
 
6. Return the helicopter in ready to flight condition. 
 
7. Record compliance of this Bollettino in the helicopter log book.

### Page 7 (OCR)

B.T. 109S-15
109-0642-01-181 LH DOOR ASSY (REF)
R ASSY (REF)  DETAIL A  (SEE FIGURE 2)
109-0642-01-182 RH
VIEW LOOKING AFT
109-0642-01-101  FWD FIREWALL ASSY (REF)
FIGURE 1
(Reference illustration)
Page 7 of 8

### Page 8 (OCR)

B.T. 1095-15.
Ø2,5 mm DRILL ON INSTALLATION
INSTALL:
MS20427M3 RIVET
OR:
MS20426T3 RIVET
OR:
A298A04TW02 RIVET
(TYP. 2 PLACES)
UPPER SEMICHANNEL OF THE
DOOR ASSY 109-0642-01 (REF.)
MS27039-08-05 SCREW
NAS1149C0332R WASHER (REF.)
(TYP. 2 PLACES)
109-0642-01-169 GASKET (REF.)
B  BOND WITH ADHESIVE EC776  (TYP. 2 PLACES)
109-0642-01-195 METALLIC SPACER (REF.)
(TYP. 2 PLACES)
109-0642-01-171
LOWER SEMICHANNELL ASSY (REF.)
MS21069L3K NUTPLATE (REF.)
(TYP. 2 PLACES)
DETAIL A
18.0 (REF.)
DRILL ON INSTALLATION  (TYP.)
ø5.0
(REF.)
73.0
109-0641-01-171  92.0 (REF.)
LOWER SEMICHANNELL ASSY (REF.)
VIEW FROM B
FIGURE 2
(Reference illustration - Dimensions in mm)
Page 8 of 8

### Page 9

Note: 
Remarks: 
Informazioni: 
Information: 
 
Al fine di gestire le varianti alla configurazione base, in relazione all’emissione del Bollettino Tecnico, preghiamo di voler compilare il presen-
te modulo in tutte le sue parti e spedirlo all’indirizzo sopra indicato. Si ringrazia per la gentile collaborazione data.  
We request your cooperation in filling this form,  in order to  keep out statistical data relevant to aircraft configuration up- to-date. The form should be filled in all 
its parts and sent to the above address. We thank you beforehand for the information given. 
MODULO APPLICAZIONE BOLLETTINO TECNICO 
TECHNICAL BULLETIN COMPLIANCE FORM 
Data: 
Date: 
Numero: 
Number: 
Revisione: 
Revision: 
Prego spedire a questo indirizzo: 
Please send to the following address: 
 
AGUSTA S.p.A. 
CUSTOMER SUPPORT 
Via per Tornavento,  15 
21019 Somma Lombardo (VA) - ITALY 
Tel.: +39 0331 711100 
Fax: +39 0331 711397 
Telefono: 
Telephone: 
Fax: 
Data Applicazione B.T.: 
B.T. Compliance Date: 
Denominazione Cliente ed Indirizzo: 
Customer Name and Address: 
Modello Elicottero 
Helicopter Model S/N Matricola Tail Number Ore Totali Total Hours Ore D.U.R. T.S.O.

### Page 10

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
