# Agusta Mandatory Bollettino Tecnico 109SP-032: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2011-1454; AD 2011-27-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Agusta Mandatory Bollettino Tecnico 109SP-032](https://openairdocs.org/service-documents/leonardo/109sp-032.md)
- Title as filed: U.S. DOT/FAA - Agusta Service Information - 1
- Pages: 7
- PDF: https://openairdocs.org/files/sha256/01/48/01489633c6c7e3fe195310fb4d80f78a79dbbb83377dda7ff95305ec81ff960c
- Page: https://openairdocs.org/service-documents/leonardo/109sp-032/file/01489633c6c7

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ALERT 
 
 
 
 
 
TRANSLATION OF  
BOLLETTINO TECNICO 
N°  109SP-032 
 
The technical content of this document is approved 
under the authority of DOA nr EASA.21J.005. 
DATE  August 05, 2011 
  
 
 REV.  xxxxxxx 
 
 
Compliance with 
this bollettino is: 
 
 
 
 
 
 
                                 ALERT                 Page 1 of 6 
 
SUBJECT: INSPECTION OF THE LEFT ELEVATOR ASSY P/N 109 -0200-02-803 
AND RIGHT ELEVATOR ASSY P/N 109-0200-02-804. 
 
REASON: Introduce an inspection to the subject elevators to verify the presence of 
cracks on the upper skin. 
 
HELICOPTERS AFFECTED: 
All the Agusta AW109SP helicopters. 
 
COMPLIANCE: 
 For those left elevator assy P/N 109-0200-02-803 and/or right elevator 
assy P/N 109-0200-02-804 having less than 400 (four hundred) flight 
hours: 
 at reaching of 400 (four hundred) flight hours within and not later 
than 30 (thirty) flight hours and subsequently each 50 (fifty) flight 
hours. 
 
 For those left elevator assy P/N 109-0200-02-803 and/or right elevator 
assy P/N 109 -0200-02-804 having more or equal than 400 (four 
hundred) flight hours: 
 within and not later than 3 0 (thirty) flight hours after the receipt of 
this Bollettino and however within and not later than November 30, 
2011, and subsequently each 50 (fifty) flight hours. 
 
DESCRIPTION: 
A case of fracture of the left elevator along the riveting of the upper skin 
to the fourth rib has been reported on an A109S helicopter. 
The performed investigations have revealed that the fracture reported on 
the elevator is due to fatigue. 
MANDATORY
An appropriate entry should  be made in the  aircraft log book upon  accomplishment.
If ownership of aircraft has changed, please, forward to new owner .
An Company
Via GiovanniAgusta, 520
21017 Cascina Costa di Samarate (VA) Italy
T el.: +39 0331-229111 - Fax: +39 0331-229605/222595

### Page 2

B.T. 109SP-032 
 
 
Page 2 of 6 
 
The left and right elevators installed o f the A109S helicopter s are very 
similar to the left elevator assy P/N 109-0200-02-803 and right elevator 
assy P/N 109-0200-02-804 of the AW109SP helicopters. 
This Bollettino is issued in order to provide the necessary instructions to 
perform a visual inspection with a 5÷10 magnification lens to verify the  
presence of cracks on the upper skin of the left elevator assy P/N 109-
0200-02-803 and right elevator assy P/N 109 -0200-02-804, in 
correspondence of the riveting of the upper skin to the fourth rib. 
In case of doubt about the presence or absence of cracks  are also given 
instructions to carry out an inspection penetrant. 
 
REQUIRED MANPOWER: 
Negligible. 
In case of liquid penetrant inspection 1 (one) hour for each elevator assy. 
 
WARRANTY: 
Within the calendar terms mentioned at point “Compliance”, the parts 
required to apply the present Bollettino shall be supplied on a free of 
charge basis by Agusta upon Customer’s request, except for consumable 
materials. 
Upon application of this Bollettino, Customers are requested to submit to 
Agusta Warranty Administration  the Technical Bulletin Compliance form, 
attached to this Bulletin duly completed in all its parts, and relevant 
M.M.I.R. (Maintenance Malfunction Information Report). 
 
REQUIRED MATERIALS: 
The following materials could be required for compliance with this 
Bollettino: 
 
P/N DENOMINATION Q.TY 
109-0200-02-803 Left elevator assy 1 
109-0200-02-804 Right elevator assy 1 
 
The following consumable materials are required for compliance with this 
Bollettino: 
 
SPECIFICATION DENOMINATION Q.TY 
TT-N-95 type 2 Aliphatic Naphtha A.R. 
 (code 531055030) 
Commercial Gauze A.R. 
 (code 590164695) 
 
SPECIAL TOOLS:  
The following special tools are required for compliance with this 
Bollettino: 
 
 P/N    DENOMINATION    
 Commercial   5÷10 magnification lens 
 P6R    Penetrant ARDROX 
 9PR5    Solvent ARDROX 
 9D1B    Developer ARDROX

### Page 3

B.T. 109SP-032 
 
 
Page 3 of 6 
 
 P/N    DENOMINATION    
 Commercial   Fine-pointed brush 
 Commercial   White light source of at least 1000 lux 
 Commercial   Soft brush 
 
WEIGHT AND BALANCE CHANGES:  
N.A. 
 
REFERENCES: 
0B-A-AMP-00-X Maintenance Publication. 
 
PUBLICATIONS AFFECTED:  
0B-B-AMPI-00-P-EASA  Maintenance Planning Information; 
0B-B-AMPI-00-P-FAA  Maintenance Planning Information; 
0B-C-AMPI-00-P-EASA  Maintenance Planning Information; 
0B-A-AMP-00-X Maintenance Publication. 
 
COMPLIANCE INSTRUCTIONS: 
(See figure 1) 
 
1. Prepare the helicopter on ground for a safe maintenance, 
disconnect any power supply. 
 
2. Gain access to the upper side of the left elevator assy P/N 109-
0200-02-803 and accurately clean inspection area using a gauze 
soaked in aliphatic naphtha (ref. figure 1). 
 
3. Using a 5 ÷10 magnification lens perform a visual inspection to 
verify the presence of cracks in the elevator upper skin in 
correspondence of the fourth rib fixing rivets line in the area 
shown in figure 1. 
 
3.1 In ca se on the elevator upper skin there is NOT presence of 
cracks, no corrective action is required. P roceed as described in 
steps 4 and following. 
 
3.2 In case on the elevator upper skin there is presence of cracks, 
contact the AgustaWestland, and the elevato r must be removed, 
in accordance with the instructions given in the 0B -A-AMP-00-X 
Maintenance Publication, to perform a repair. 
 
3.3 In case of doubt about the presence of cracks  on the elevator 
upper skin, proceed in the following liquid penetrant inspection: 
 
CAUTION 
Personnel conducting the liquid penetrant 
inspection must be qualified in accordance 
with EN4179/NAS410A practise or other 
equivalent practise or standard.

### Page 4

B.T. 109SP-032 
 
 
Page 4 of 6 
 
3.3.1 If necessary clean again with aliphatic naphtha the area to 
inspect in order to remove the contaminants. Leave dry the 
aliphatic naphtha. 
 
3.3.2 Outline the area to inspect using only tape in which the does not 
absorb the solvent. 
 
NOTE 
The penetrant, the part to be inspected 
and the room temperatures shall be 
between 15÷45 °C. 
 
3.3.3 Using a fine -pointed brush  apply the P6R penetrant in all the 
area to inspect (ref. figure 1) for 30÷40 minutes dwell time. 
 
3.3.4 Under a white light source of at least  1000 lux, remove excess 
penetrant firstly with a dry clean gauze and then a gauze 
dampened (NOT SOAKED) with 9PR5 solvent. 
 
NOTE 
The solvent must never be poured directly 
over the area to inspect. 
 
3.3.5 Repeat the removal of the excess penetrant with gauze 
dampened with 9PR5 solvent, until it was completely removed 
any residual background colour. 
 
3.3.6 After complete evaporation of solvent, apply a  thin uniform layer 
of 9D1B developer spraying it from a distance of 30÷40 cm. Prior 
to use shake the developer spray can for at least 1 minute. 
 
CAUTION 
Accidental developer leakages require t he 
full clean of the part and the full re 
processing of the part. 
 
3.3.7 After 10 minutes of developer dwell time, carefully check the 
inspection area (ref. figure 1) to interpret any red signs on a white 
background. 
 
CAUTION 
The operator cannot wear sungl asses or 
photochromic lenses. 
 
3.3.8 In case on the elevator upper skin there is presence of cracks, 
contact the AgustaWestland, and the elevator must be removed, 
in accordance with the instructions given in the 0B -A-AMP-00-X 
Maintenance Publication, to perform a repair.

### Page 5

B.T. 109SP-032 
 
 
Page 5 of 6 
 
3.3.9 After inspection, accurately clean the affected area from any 
used products residual with gauze soaked in 9PR5 solvent and 
eventually using a soft brush. 
 
4. Repeat steps 2 and 3 for the right elevator assy P/N 109-0200-
02-804. 
 
5. Return the helicopter to a ready to flight condition. 
 
6. Record compliance with this Bollettino in the helicopter log book.

### Page 6 (OCR)

B.T. 109SP-032
INSPECT THIS AREA FOR CRAKS WITH  5÷10 MAGNIFICATION LENS OR WITH PENETRANT  FOURTH RIB  60 mm  VIEW LOOKING DOWN  109-0200-02-804 RIGHT ELEVATOR ASSY (SHOWN)  109-0200-02-803 LEFT ELEVATOR ASSY (OPPOSITE)
FWD
UPPER SKIN
CHORD LINE 625.0 (REF)  C=
FIGURE 1
Page 6 of 6

### Page 7

Note: 
Remarks: 
Informazioni: 
Information: 
 
Al fine di gestire le varianti alla configurazione base, in relazione all’emissione del Bollettino Tecnico, preghiamo di voler compilare il presen-
te modulo in tutte le sue parti e spedirlo all’indirizzo sopra indicato. Si ringrazia per la gentile collaborazione data.  
We request your cooperation in filling this form,  in order to  keep out statistical data relevant to aircraft configuration up- to-date. The form should be filled in all 
its parts and sent to the above address. We thank you beforehand for the information given. 
MODULO APPLICAZIONE BOLLETTINO TECNICO 
TECHNICAL BULLETIN COMPLIANCE FORM 
Data: 
Date: 
Numero: 
Number: 
Revisione: 
Revision: 
Prego spedire a questo indirizzo: 
Please send to the following address: 
 
AGUSTA S.p.A. 
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING DPT.
Via del Gregge, 100 
21015 Lonate Pozzolo (VA) - ITALY 
Tel.: +39 0331 664600 
Fax: +39 0331 664684
Telefono: 
Telephone: 
Fax: 
Data Applicazione B.T.: 
B.T. Compliance Date: 
Denominazione Cliente ed Indirizzo: 
Customer Name and Address: 
Modello Elicottero 
Helicopter Model S/N Matricola Tail Number Ore Totali Total Hours Ore D.U.R. T.S.O.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
