# Leonardo Bollettino Tecnico 109SP-110: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2018-0726; AD 2019-09-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Bollettino Tecnico 109SP-110](https://openairdocs.org/service-documents/leonardo/109sp-110.md)
- Title as filed: Leonardo Bollettino Tecnico 109SP-110
- Pages: 23
- PDF: https://openairdocs.org/files/sha256/68/73/6873d1f57b37b61b753f20898d1a35d551dc98be42070f046617de3122082834
- Page: https://openairdocs.org/service-documents/leonardo/109sp-110/file/6873d1f57b37

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

BOLLETTINO TECNICO N° 109SP-110 
The technical content of this document is approved 
under the authority of DOA nr. EASA.21J.005 DATE February 13, 2017 
REV. / 
Compliance with 
this Bulletin is: 
Page 1 of 22 
SUBJECT 
RESCUE HOIST OPTIONAL EQUIPMENT P/N 109-B810-16-101 AND 
P/N 109-B810-16-201. 
REASON 
Provide the necessary instructions to inspect and modify the actual rescue hois t 
installation. 
HELICOPTERS AFFECTED 
All the AW109SP equipped with the rescue hoist kit  P/N 109-B810- 16-101 
and -201. 
COMPLIANCE 
PART I^ 
Within and not later than 10 FH after the receipt of this Bollettino tecnico. 
PART II^ 
Within and not later than 25 FH after the receipt of this Bollettino tecnico. 
MANDATORY
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
ALERT

### Page 2

B.T. 109SP-110 
Page 2 of 22 
PART III^ 
Before the next rescue hoist operation. 
DESCRIPTION 
As a result of the investigation of an operational event which led to a damage of the 
Rescue Hoist cable,  Leonardo Helicopters decided to  introduce a one -time 
inspection of the rescue hoist handle, of the passengers’ cabin doorframe and , in 
case of damages,  of the rescue hoist cable (PART I^), to change  the attaching 
means of the Rescue Hoist handle on the Rescue Hoist support (PART II^) and to 
temporarily introduce in the Section Normal Procedure a n additional check of the 
rescue hoist cable  to be performed before the first flight of the day  (PART III^, this 
waiting for the full implementation of a handle and doorframe protection). 
REQUIRED MANPOWER 
PART I^ 
An estimated 2 (two) manpower hours are required for compliance with this Part. 
PART II^ 
An estimated 1 (one) manpower hours are required for compliance with this Part. 
PART III^ 
Negligible. 
 
WARRANTY 
Owners/Operators who comply with the instructions of this Bulletin, no later than the 
applicable date in the “Compliance section” will be eligible to receive REQUIRED 
MATERIALS on free of charge basis, except for Consumable Materials & Special 
Tools.  
NOTE: Customers who fail to comply with the instructions in this bulletin before the 
compliance date are not eligible for the aforementioned special policy.  
 
Please Issue relevant M.M.I.R. form ( (M)aintenance (M)alfunction (I)nformation 
(R)eport ) to your Warranty Administration Dpt.

### Page 3

B.T. 109SP-110 
Page 3 of 22 
  
NOTE: INSPECTION REPORT is mandatory; in case the MMIR is not accompanied 
by these documents, it will be rejected. Please destroy locally the removed parts. 
REQUIRED MATERIALS 
The following materials are required for compliance with this Bollettino Tecnico: 
PART I^: None 
 
PART II^: 
P/N DESCRIPTION Q.TY NOTE 
MS27039C1-13 Screw, Machine  .2 Local Supply 
NAS1149C0332R  Washer .2 Local Supply 
NAS1149C0316R  Washer .2 Local Supply 
MS21042L3  Nut, self-locking  .2 Local Supply (*) 
 
(*) To get this item refer to the approved manufacturer list only (Refer to Data 
Module 0B-A-00-00-00-00A-947A-D within the 0B -A-IPD-00-X “Illustrated Parts 
Data”). 
 
Moreover the following consumable materials, or equivalent, are necessary to 
accomplish this Bollettino Tecnico: 
Spec./AW code number DESCRIPTION Q.TY NOTE 
Commercial  
Type 03 Cl 2 
(AW code: 900004957) 
Loctite 242 AR Local Supply 
 
PART III^: None 
SPECIAL TOOLS 
N.A. 
WEIGHT AND BALANCE CHANGES 
N.A.

### Page 4

B.T. 109SP-110 
Page 4 of 22 
REFERENCES 
 0B-A-AMP-00-X Maintenance Publication. 
 0B-B-ASRP-00-X Structural Repair Publication. 
 109G0040A019 AW109SP Rotorcraft Flight Manual – Optional Equipment 
Supplements. 
 109G0040A021 AW109SP Rotorcraft Flight Manual – Optional Equipment 
Supplements REGA. 
PUBLICATIONS AFFECTED 
 0B-A-AMP-00-X Maintenance Publication. 
 0B-A-IPD-00-X Illustrated Parts Data Information. 
 
COMPLIANCE INSTRUCTIONS 
GENERAL NOTES 
Replace the hardware found damaged during the following 
operation. 
PART I 
1. Prepare the helicopter on ground for a safe maintenance and disconnect 
any power supply, in accordance with the instructions given in the  
0B-A-AMP-00-X Maintenance Publication. 
2. Inspect the rescue hoist handle assy (ref. Figure 1)  and upper part of 
cabin doorframe (ref. Figure 3) for any damage caused by hoist cable (ref. 
Figures 10 and 11). 
2.1 If no damage is found go to step 4. 
2.2 If damage is found, repair in accordance with the instructions given 
in the 0B-B-ASRP-00-X Structural Repair Publication.

### Page 5

B.T. 109SP-110 
Page 5 of 22 
3. Inspect the first 6 meters/20 feet of the hoist cable as follows: 
WARNING  
The rescue hoist contains an Electrically -Initiated 
Explosive Device (EIED). Be careful when you do the 
operation test of the rescue hoist system.  
– Make sure that there are no radio or rad ar 
transmissions in the safety distance. Refer to the 
local regulations for more data.  
– Make sure that the electrical power to the EIED is 
disconnected  
– Keep your hands, cloths and body away from the 
components that are in movement.  
– Always wear protective  goggles and gloves when 
you work on the hoist.  
– Only approved persons can stay near the helicopter 
during the operations on the rescue hoist.  
If you do not obey these instructions, you can cause an 
explosion and possibly cause an injury to persons. 
 
3.1 Connect an external electrical power in accordance with the 
instructions given in the 0B-A-AMP-00-X Maintenance Publication. 
3.2 On the circuit breaker panel make sure that the circuit breakers 
that follow are closed:  
– HOIST CONTR  
– HOIST PWR. 
 
CAUTION 1:  
Do not extend the hoist cable beyond the length that 
enables the cable hook assembly to contact the ground 
unless provision is made to prevent damage and 
entanglement of the cable. 
 
CAUTION 2:  
During the following procedures, reel cable  out using 
care not to pull cable taut against the cable guide 
rollers, as kinking of the cable can result. Avoid 
damaging cable on rough surfaces, such as the ground.

### Page 6

B.T. 109SP-110 
Page 6 of 22 
NOTE 1: 
When reeling-out the hoist cable, gently coil the cable 
into a 1 meter per 1 meter container (as a minimum), or 
equivalent, which will prevent cable contact with the 
ground or other abrasive surface. 
3.3 Slowly rotate the control pendant REEL IN/OUT thumbwheel in the 
REEL OUT direction and reel-out the cable to 6 meters / 20 feet 
length at a controlled speed. 
NOTE 2: 
Cleaning the cable with a low-lint cloth will aid in the 
inspection requirement to locate broken wires. Broken 
wires will snag the cloth being used to clean the cable. 
3.4 Perform cable dimension check by using a micrometre, (ref. Figure 
4) measure the diameter of the rescue hoist cable as follows:
3.4.1 Measurements are to be taken at 1 meter / 3.28 feet intervals and, 
in addition, at any position where it is believed that necking or 
wear may have occurred. 
3.4.2 Measure the diameter of the cable 90 degrees apart (diameter A 
and B). 
3.4.3 Add the two measurements together and divide by 2 ( (A+B)/2 ). If, 
at any position the cable diameter is less than 4.70 mm / 0.185 
inch replace the cable in accordance with the instructions given in 
the 0B-A-AMP- 00-X Maintenance Publication (Data Module 
0B-B-25-91-01-08A-921A-A). 
3.5 Slowly rotate the control pendant REEL IN/OUT thumbwheel in the 
REEL IN direction and slowly reel-in the cable at a controlled 
speed. 
3.6 As the cable is reeling in, remove dirt from cable and visually 
inspect cable for broken wires, kinks, bird caging, flattened areas, 
abrasion, necking or other visible damage (r ef. Figures 5 to 9 for 
these damages examples).  
3.7 Slowly reel-in the cable until the limit switches stop the hoist 
operation automatically and the final reel-in movement applies a 
tension to the hoist cable.

### Page 7

B.T. 109SP-110 
Page 7 of 22 
3.8 Release the control pendant REEL IN/OUT thumbwheel. Make 
sure the thumbwheel  returns to the center (neutral) position 
automatically. 
3.9 Disconnect the external power source in accordance with the 
instruction given in the 0B-A-AMP-00-X Maintenance Publication. 
4. Return the helicopter to a ready to flight condition. 
5. Fill and forward the Technical Bulletin Compliance Form to Leonardo 
Helicopters. To following address: 
AW109 Product Support Engineering: 
(AW109.mbx.aw@leonardocompany.com). 
As an alternative, gain access to My Communications section on 
Leonardo Web Portal on AW website and compile the “Technical Bulletin 
Application Communication”. 
6. Record compliance with PART I of this Bollettino Tecnico in the helicopter 
log book. 
 
PART II 
1. Prepare the helicopter on ground for a safe maintenance and disconnect 
any power supply, in accordance with the instructions given in the  
0B-A-AMP-00-X Maintenance Publication. 
2. Gain access to the handle assy of the rescue hoist. 
3. In accordance with the ins tructions given in the 0B -A-AMP-00-X 
Maintenance Publication and Figure 1,  remove (FWD zone) the nut 
MS21042L3, the washer P/N NAS1149C0316R, the bolt P/N AN3C6 and 
the washer P/N NAS1149C0332R.

### Page 8

B.T. 109SP-110 
Page 8 of 22 
NOTE 1 
Apply one drop of the Adhesive (Loctite) on the threads. 
NOTE 2 
It is allowed to add NAS1149D0316J or NAS1149D0332J 
or NAS1149D0616J between the handle assy and the 
plate up to fill the gap between the two surfaces. 
 
4. With reference to Figure 2, install the washer P/N NAS1149C0332R, the 
machine screw MS27039C1 -13 with head on outer side, the washer  
P/N NAS1149C0316R and the nut MS21042L3 on inner side. 
 
4.1 Torque the nut to 2.3 – 2.8 Nm. 
 
5. In accordance with the instructions given in the 0B -A-AMP-00-X 
Maintenance Publication and Figure 1,  remove (AFT zone) the nut 
MS21042L3, the washer P/N NAS1149C0316R, the bolt P/N AN3C6 and 
the washer P/N NAS1149C0332R. 
 
NOTE 3 
Apply one drop of the Adhesive (Loctite) on the threads. 
NOTE 4 
It is allowed to add NAS1149D0316J or NAS1149D0332J 
or NAS1149D0616J between the handle assy and the 
plate up to fill the gap between the two surfaces. 
 
6. With reference to Figure 2, install the washer P/N NAS1149C0332R, the 
machine screw MS27039C1 -13 with head on outer side , the  washer  
P/N NAS1149C0316R and the nut MS21042L3 on inner side. 
 
6.1 Torque the nut to 2.3 – 2.8 Nm. 
 
7. Return the helicopter to a ready to flight condition.

### Page 9

B.T. 109SP-110 
Page 9 of 22 
8. Fill and forward the Technical Bulletin Comp liance Form to Leonardo 
Helicopters. To following address: 
AW109 Product Support Engineering: 
(AW109.mbx.aw@leonardocompany.com). 
As an alternative, gain access to My Communications section on 
Leonardo Web Portal on AW website and compile the “Technical Bulletin 
Application Communication”. 
9. Record compliance with PART II of this Bollettino Tecnico in the 
helicopter log book. 
 
 
PART III 
NOTE 
The additional daily pre -flight check must be performed 
after the check at point 8 and before the check at point 9. 
 
1. Applicable to AW109SP S/N 22203, 22213 and subs.: insert the “Normal 
Procedure – Additional check” page reported in Annex A of this Bollettino 
Tecnico at page 13 of 34 of Supplement 5  of the Docu ment 
109G0040A019 AW109SP Rotorcraft Flight Manual – Optional 
Equipment Supplements. 
Applicable to AW109SP S/N 22202, 22204 to 22212: insert the “ Normal 
Procedure – Additional check” page reported in Annex A of this Bollettino 
Tecnico at page 19 of 34 of S upplement 9.2 -5 of the Document 
109G0040A021 AW109SP Rotorcraft Flight Manual – Optional 
Equipment Supplements REGA.

### Page 10

B.T. 109SP-110 
Page 10 of 22 
2. Fill and forward the Technical Bulletin Compliance Form to Leonardo 
Helicopters. To following address: 
AW109 Product Support Engineering: 
(AW109.mbx.aw@leonardocompany.com). 
As an alternative, gain access to My Communications section on 
Leonardo Web Portal on AW website and compile the “Technical Bulletin 
Application Communication”. 
Record compliance with PART III of this Bollettino Tecnico in the 
helicopter log book.

### Page 11 (OCR)

B.T. 109SP-110
→Q
Remove
-NAS1149C0332R WASHER
Remove
AN3C6 BOLT
Remove
MS21042L3 NUT
Remove
NAS1149C0316R WASHER
109-0717-91-113
HANDLE ASSY REF
Remove
Remove  AN3C6 BOLT  Remove
MS21042L3 NUT  NAS1149C0332R WASHER
Remove
NAS1149C0316R WASHER
Figure 1
Page 11 of 22

### Page 12 (OCR)

B.T. 109SP-110
NAS1149C0316R WASHER
- MS21042L3 NUT
MS27039C1-13
MACHINE SCREW
NAS1149C0332R WASHER
109-0717-91-113
HANDLE ASSY REF
MS21042L3 NUT
MS27039C1-13  NAS1149C0316R WASHER
MACHINE SCREW
NAS1149C0332R WASHER
Figure 2
Page 12 of 22

### Page 13

B.T. 109SP-110 
Page 13 of 22 
  
 
 
 
 
 
 
 
Figure 3  
Passengers’ Cabin Doorframe Inspection Area

### Page 14

B.T. 109SP-110 
Page 14 of 22 
 
 
 
Figure 4 
Cable Diameter Measuring

### Page 15

B.T. 109SP-110 
Page 15 of 22 
 
 
Figure 5 
Cable Broken Wire

### Page 16

B.T. 109SP-110 
Page 16 of 22 
 
 
Figure 6 
Cable Severe Kink

### Page 17

B.T. 109SP-110 
Page 17 of 22 
 
 
Figure 7 
Cable Necking

### Page 18

B.T. 109SP-110 
Page 18 of 22 
 
 
Figure 8 
Cable Bird Cage

### Page 19

B.T. 109SP-110 
Page 19 of 22 
 
 
 
 
 
 
 
 
Figure 9 
Cable Abrasion And Flattened

### Page 20 (OCR)

B.T. 109SP-110
Figure 10
Handle damages
(for reference only)
Figure 11
Passengers' Caibn doorframe damages
(for reference only)
Page 20 of 22

### Page 21

ANNEX A                                                           B.T. 109SP-110 
Page 21 of 22 
 
ANNEX A

### Page 22

B.T. 109SP-110                                                          ANNEX A 
Page 22 of 22 
 
 


### Page 23

Remarks:
Information: 
 BOLLETTINO TECNICO COMPLIANCE FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
