# Agusta Bollettino Tecnico 109-110: Revision A

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2008-0834; AD 2008-24-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Agusta Bollettino Tecnico 109-110](https://openairdocs.org/service-documents/leonardo/sb-109-110.md)
- Title as filed: U.S. DOT/FAA - Agusta BT 109-110 Rev A
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/d9/74/d9744f0bcf3757341d25d66d3f3e22181f1395d0efb5447fc4519efd3b47ed53
- Page: https://openairdocs.org/service-documents/leonardo/sb-109-110/file/d9744f0bcf37

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AGUSTA  Via Giovanni Agusta, 520  21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331-229111 - Fax: +39 0331-229605/222595
AN AGUSTAWESTLAND COMPANY
TRANSLATION OF
BOLLETTINO TECNICO  Ne 109-110
The technical content of this document is approved  DATE July 28, 1999
under the authority of DOA nr. EASA.21J.005
REV. A December 12, 2005
Compliance with  MANDATORY
this bulletin is:
THIS BOLLETTINO CANCELS AND SUPERSEDES THE BOLLETTINO TECNICO
TELEGRAFICO N° 109-5, DATED JANUARY 27, 1987.
SUBJECT: INSPECTION FOR CRACKS OF TAIL ROTOR BLADES P/N
109-0132-02-11/-15/-121.
REASON: To emphasize the importance of performing a detailed inspection of the
subject tail rotor blades for cracks, already prescribed in Bollettino
tecnico telegrafico n° 109-5, dated January 27, 1987.
HELICOPTERS AFFECTED:
All Agusta helicopters A109A and A109AIl equipped with tail rotor blades
P/N 109-0132-02-11/-15/-121 with 400 (four-hundred) or more flight  JA
hours.
NOTE
Tail rotor blades P/N 109-0132-02-125 do
not  require compliance with this
Bollettino.
COMPLIANCE:
PART I^:
Upon receipt of this Bollettino for blades having accumulated 400 (four
hundred) flight hours, if the Bollettino tecnico telegrafico n° 109-5, dated
January 27, 1987 has not been accomplished.
PART I|^:
Prior to the first flight of the day.
PART IIIA:
Each 100 (hundred) flight hours.
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Page 1 of 6 A

### Page 2 (OCR)

B.T. 109-110
DESCRIPTION:
A second case has been reported of failure of one tail rotor blade P/N
109-0132-02, followed by the loss of tail rotor and 90° gearbox assembly.
The crack originated in the central area of the blade, in proximity of the
tip of the root doubler in the chordwise sense.
The scope of this Bollettino is to prescribe a visual inspection (PART II^)
and a liquid penetrant inspection (PART I^ and PART III) for presence of
eventual cracks.
Subsequently new tail rotor blade P/N 109-0132-02-125 were designed
and certified which have improved structural characteristics with respect
to the blades P/N 109-0132-02-11/-15/-121, and do not require
compliance with this Bollettino.
REQUIRED MANPOWER:
The following estimated manpower hours are necessary, for each blade,
for compliance with this Bollettino :
PART I^: 1.5 manpower
PART I|^: negligible
PART III^: 1 manpower
WARRANTY: N.A.
REQUIRED MATERIALS:
The following consumable materials are necessary to accomplish this
Bollettino:
PARTI^:
SPECIFICATION  NOMENCLATURE  Q.TY
MIL-R-25134  Ardrox 204S, solvent  A.R
(code 531056779)
MIL-L-81352  Transparent acrylic lacquer  A.R.
or MIL-PRF-81352
In addition the materials indicated in the PART III^ of this Bollettino are
necessary.
PART I^:
SPECIFICATION  NOMENCLATURE  Q.TY
TT-N-95  Aliphatic naphtha  A.R.
(code 531055030)
PARTE I|^:
SPECIFICATION  NOMENCLATURE  Q.TY
TT-N-95  Aliphatic naphtha  A.R.
(code 531055030)
Materials to perform the liquid penetrant inspection:
• visible dye penetrant P6R available from BRENT International,
• dry developer 9D1B available from BRENT International,
• a white light source able to give an illuminance of at least 1000 lux on
the area of inspection.
A Page 2 of 6

### Page 3 (OCR)

B.T. 109-110.
Instead of the indicated penetrant and developer, other products can be
used providing that:
• they comply with the requirements of AMS 2644 (type 2 and method
"C" for the penetrant and form "e" for the developer),
• they are listed in the pertinent QPL-AMS-2644-1,
• they are (penetrant and dry developer) produced by the same
company.
SPECIAL TOOLS: N.A.
WEIGHT AND BALANCE CHANGES: N.A.
REFERENCES:
Maintenance Manual.
PUBLICATIONS AFFECTED:
Maintenance Manual.
Flight Manual.
COMPLIANCE INSTRUCTIONS:
NOTE
The procedure reported below is applicable
to each one of the two tail rotor blades, if
affected by this Bollettino.
PART I^:
1.  Identify and outline with adhesive tape the inspection area in
accordance with figure 1 (blade upper and lower sides).
2.  Using solvent Ardrox 204S or equivalent (MIL-R-25134), remove
the finish paint in the above area without removing the primer
underneath.
To remove the transparent paint, use solvent abundantly, in order to
completely remove all paint residue.
CAUTION 1
Paint removal procedure is of the utmost
importance. Failure to thoroughly remove all
paint may lead to the occlusion of cracks.
CAUTION 2
Use  of  methylethylketone  iS  not
recommended as damage to the bonding
agent may occur.
Do not use abrasive materials to remove the
paint to avoid damaging the areas of the
blade. In case of presence of damage refer
to the Maintenance Manual.
Page 3 of 6 A

### Page 4 (OCR)

B.T. 109-110
3. Perform the liquid penetrant inspection as follows:
CAUTION
Personnel conducting the liquid penetrant
inspection for this specification must be
qualified in accordance with the ASNT
practice SNT-TC-1A or other equivalent
practice or standard.
The inspection shall comply with the
requirements of ASTM E 1417. The blade,
penetrant and ambient temperatures shall be
in the range from 4 to 45 °C.
3.1. On the area of paint removal apply the penetrant for 30 to 40
minutes of dwell time.
NOTE
Remove the excess of penetrant with a
cheesecloth soaked with aliphatic naphtha or
equivalent. The solvent shall not be poured
directly on the inspection area.
Apply a uniform and thin layer of developer by means of a powder
bellows; after 10 to 15 minutes of developer time, illuminate the
area at 1000 lux minimum and carefully inspect it.
If presence cracks is detected, the blade must be removed from
service. In this case, please inform Agusta immediately.
The potential crack would be shown running
in a straight line, exactly parallel to the blade
chord; it does not therefore follow the contour
of the doubler and it is clearly different from
evidence of bonding agent porosity that may
appear along the edge of the doubler.
Upon completion of the inspection, if no cracks are found, clean
he stripped areas with aliphatic naphtha, and protect with
ransparent acrylic lacquer in accordance with the Maintenance
Return the helicopter in ready to flight condition.
PART I^:
Use a cheesecloth soaked with aliphatic naphtha or equivalent to
clean the protected area with transparent lacquer of the tail rotor
blade (ref. figure 1).
A Page 4 of 6

### Page 5 (OCR)

B.T. 109-110
2.  Perform a visual inspection on blade upper and lower sides for
cracks, if necessary use a 3 to 5 power magnifying glass.
If presence of cracks is suspected perform the PART III^ of this
Bollettino.
CAUTION
In case of presence of other damage (nicks,
dents, corrosion, etc.) on the metal refer to
Maintenance Manual.
PART III^:
1.  Using solvent Ardrox 204S or equivalent (MIL-R-25134), remove
the transparent lacquer in the identified area shown in figure 1
(blade upper and lower sides), without removing the primer
underneath.
To remove the transparent lacquer use solvent abundantly, in
order to completely remove all paint residue.
CAUTION 1
Paint removal procedure is of the utmost
importance. Failure to thoroughly remove all
paint may lead to the occlusion of cracks.
CAUTION 2
Use  of  methylethylketone  not
recommended as damage to the bonding
agent may occur.
Do not use abrasive materials to remove the
paint to avoid damaging the areas of the
blade. In case of presence of damage refer
to the Maintenance Manual.
Perform the liquid penetrant inspection in accordance with
paragraph 3. of PART I^ of this Bollettino.
If presence of cracks is detected, the blade must be removed from
service. In this case, please inform Agusta immediately.
Page 5 of 6 A

### Page 6 (OCR)

Page 6 of 6  B.T. 109-110
Center of the blade retention bolt hole
100 mm
190 mm -
220 mm -
Inspection area (upper and lower sides)
FIGURE 1

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
