# Leonardo Bollettino Tecnico 109-125: Revision A

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-0194; AD 2021-07-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Bollettino Tecnico 109-125](https://openairdocs.org/service-documents/leonardo/sb-109-125.md)
- Title as filed: Leonardo Helicopters ASB 109-125 Rev A
- Pages: 10
- PDF: https://openairdocs.org/files/sha256/e5/cd/e5cdca69adf9af84c9f9f076f9a69aa2d33de0d7298bdcaff0802bbb3a6f8db7
- Page: https://openairdocs.org/service-documents/leonardo/sb-109-125/file/e5cdca69adf9

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N°  109-125 
DA TE:  December 13, 2007 
REV. :  A - October 19, 2020 
Pa ge 1 of 9 
TITLE 
INSPECTION OF THE TIP CAP P/N 709-0103-29-109 OF THE MAIN ROTOR BLADES 
P
/N 709-0103-01-101/-105/-109 
REVISION LOG 
Revision A of this Service Bulletin is issued to introduce the following modification: 
-
 update the BT 109-125 to the new Service Bulletin template; 
- eliminate the magnifying glass inspection prescribed in the first issue of this SB; 
Helicopters which are already complying with the previous issue of this Service Bulletin or 
with Paragraph 62-10-25C of the applicable MM shall only apply the recurring inspection 
following the Accomplishment Instructions required by this revision without changing their 
current scheduling. 
Revision bars in the outer margin identify changes. 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S.B. N°109-125 ALERT 
 DATE: December 13, 2007 
Page 2 of 9 REVISION: A - October 19, 2020 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
All the main rotor blades P/N 709-0103-01-101/-105/-109 installed on the Leonardo 
S.p.a. A109C helicopters (and/or stored as spare parts) equipped with tip cap  
P/N 709-0103-29-109. 
B. COMPLIANCE 
Tip Cap P/N 709-0103-29-109 that have accumulated more than 600 (six hundred) flight 
hours: 
 Within and not later than 50 flight hours after the issue of this Service Bulletin. 
Subsequently every 50 (fifty) flight hours. 
Tip Caps P/N 709-0103-29-109 that have accumulated less than 600 (six hundred) flight 
hours: 
 Within and not later than 600 (six hundred) flight hours. Subsequently every 50 
(fifty) flight hours. 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin is issued in order to provide the necessary instruction on how to 
perform the detailed inspection of Main Rotor Tip Cap Assy P/N 709-0103-29-109. 
E. DESCRIPTION 
In 2007 some cases of loss of a part of the tip P/N 709-0103-29-109 of the main rotor 
blade P/N 709-0103-01 had been reported on an A109E helicopter model, with 
subsequent increase of helicopter vibratory level. The cause of this loss is the fracture 
of the welded bead (joint line of shells) of the tip leading edge. The action prescribed by 
first issue of this Service Bulletin (and subsequently added in the Maintenance Manual) 
consisted in a visual inspection with the aid of a 10x magnifying glass. In case of doubts 
about the presence of cracks and/or damage on the welded bead of the tip cap, it was 
prescribed to perform a detailed inspection with dye penetrant method. Recently, few 
cases of tip cap detachment have occurred, leading to the consideration that the visual 
inspection cannot be considered sufficiently conservative anymore. Thus, the Revision 
A of this SB, is issued to remove the magnifying glass inspection leaving the dye 
penetrant method as the only applicable one.

### Page 3

S.B. N°109-125 ALERT 
DATE: December 13, 2007 
REVISION: A - October 19, 2020 Page 3 of 9 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA nr. 
EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin 3 (three) MMH are deemed necessary. 
MMH are based on hands-on time and can change with personnel and facilities 
available. 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
1) PUBLICATIONS 
PARAGRAPH/SECTION DESCRIPTION PART 
PAR01 00-20-1 Helicopter safety - 
NOTE 
The following paragraph is referred to 
Overhaul Manual. 
PARAGRAPH/SECTION DESCRIPTION PART 
PAR02 62-11-01 Main rotor blade - 
2) ACRONYMS 
DOA Design Organization Approval 
EASA European Aviation Safety Agency 
IETP Interactive Electronic Technical Publications 
IPC Illustrated Parts Catalog

### Page 4

S.B. N°109-125 ALERT 
 DATE: December 13, 2007 
Page 4 of 9 REVISION: A - October 19, 2020 
LHD Leonardo Helicopters Division 
MM Maintenance Manual 
MMH Maintenance Man Hours 
P/N Part Number 
PTUM Pictorial Tools Usage Manual 
3) ANNEX 
N.A. 
J. PUBLICATIONS AFFECTED 
A109C MM - Maintenance Manual 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 5

S.B. N°109-125 ALERT 
DATE: December 13, 2007 
REVISION: A - October 19, 2020 Page 5 of 9 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
N.A. 
2) CONSUMABLES 
The following consumable materials, or equivalent, are necessary to accomplish this 
Service Bulletin: 
# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 
1 TT-N-95, Type II Aliphatic naphtha (C059) AR (2) - 
2 ASTM D235 Cleaning solvent (C120) AR (1)(2) - 
3 SAE-AMS-2644, Type II, Method C Dye Penetrant (C041) AR (2) - 
4 SAE-AMS-2644, Form e, Type II Developer (C404) AR (2) - 
5 Commercial Masking adhesive tape AR (2) - 
6 Commercial Abrasive Paper  (grit no. 320 or finer grit 300) AR (2) - 
Refer also to AMDI for the consumable materials required to comply with the MM 
Paragraphs referenced in the accomplishment instructions. 
3) LOGISTIC MATRIX 
N.A. 
NOTE 
(1) Solvent (C120) is considered alternative at Solvent (C059). 
(2) Item to procured as local supply. 
B. SPECIAL TOOLS 
Refer to PTUM for the special tools required to comply with the MM Paragraphs 
referenced in the accomplishment instructions. 
C. INDUSTRY SUPPORT INFORMATION 
WARRANTY: Owners/Operators who comply with the instructions of this Service 
Bulletin no later than the applicable date in the “Compliance” section will be eligible to 
receive REQUIRED MATERIALS on free of charge basis, except for Consumable 
Materials and Special Tools.  
NOTE: Customers who fail to comply with the instructions in this Service Bulletin before 
the compliance date are not eligible for the aforementioned special policy.  
Please Issue relevant MMIR Form to your Warranty Administration Dpt.

### Page 6

S.B. N°109-125 ALERT 
 DATE: December 13, 2007 
Page 6 of 9 REVISION: A - October 19, 2020 
NOTE 1: In case of cracks found after inspection, as reported on Point 3.8 of this Service 
Bulletin, please kindly inform urgently LHD’s personnel and/or PSE, in order to receive 
all directives.

### Page 7

S.B. N°109-125 ALERT 
DATE: December 13, 2007 
REVISION: A - October 19, 2020 Page 7 of 9 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the modification 
area and adequately protect them until their later re-
use. 
b) All lengths are in mm. 
NOTE 
The procedures reported below are applicable to each 
one of the four main rotor blades and does not require 
to remove it from the helicopter. 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
NOTE 
Next step should be performed only at the first 
scheduled inspection. 
NOTE 
This inspection does not require removal of the blade 
from the helicopter. 
2. With reference to Figure 1 Detail A, on both uppe r and lower sides of the Main Rotor Tip 
Cap Assy P/N 709-0103-29-109 remove paint from the indicated area using abrasive 
paper grit n°320 or more fine. Mask surrounding painted areas using adhesive tape. 
CAUTION 
The personnel in charge of colour contrast liquid 
penetrant inspection here required shall be qualified in 
accordance with standard EN4179/NAS410 or 
equivalent. The temperature of the blade and of the 
penetrant liquid must be between 4°C and 45°C. 
3. Using the visible dye penetrant method, perform t he inspection of the welded bead on tip 
cap leading edge (joint line between the two metal shell) for presence of cracks as follows. 
3.1 Thoroughly degrease the inspection area with a lint free clean cloth soaked with 
solvent. Leave the solvent evaporate completely.

### Page 8

S
.B. N°109-125 ALERT 
DATE: December 13, 2007 
Page 8 of 9 REVISION: A - October 19, 2020 
3.2 Mask with adhesive tape the trailing edge inboard for 30 mm to avoid possible 
seepage of penetrant in the tip cap. 
3.3 Apply the SAE-AMS-2644 Dye Penetrant to the inspection area extending 
approximately 5 mm inboard from trailing edge on both upper and lower sides. 
Penetrant dwell time is 30 to 40 minutes. 
3.4 Remove excess penetrant with a dry lint free cloth followed by a cloth dampened 
with solvent until the background colour has been completely removed. 
NOTE 
Do not pour the solvent directly on the inspection area. 
3.5 Apply a thin and uniform layer of SAE-AMS-2644 De veloper; 10 to 15 minutes later 
illuminate the inspection area to 1000 lux and inspect for presence of cracks. 
3.6 Upon completion of the inspection clean the affected area with a clean lint free 
cloth followed by a cloth dampened with solvent. 
NOTE 
The paint removed from the tip cap must not be 
restored. 
3.7 If no presence of cracks is found on the main rot or blade tip cap return the blade 
to service. 
3.8 In case of presence of cracks inform Design Authority and, in accordance to OM 
Paragraph 62-11-01, replace the Main Rotor Tip Cap P/N 709-0103-29-109. 
4. Return the helicopter to a ready to flight condition and record for compliance with this
Service Bulletin on the helicopter logbook.
5. Send the attached compliance form to the following mail box:
engineering.support.lhd@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal and 
compile the “Service Bulletin Application Communication”.

### Page 9

Figure 1 
S.B. N°109-125 
DATE: December 13, 2007 
REVISION: A - October 19, 2020 Page 9 of 9

### Page 10

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
