# Leonardo Alert Service Bulletin 109-158: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2023-2238, the docket of AD 2024-15-11. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 109-158](https://openairdocs.org/service-documents/leonardo/sb-109-158.md)
- Title as filed: Leonardo Helicopters ASB 109-158
- Pages: 25
- PDF: https://openairdocs.org/files/sha256/27/d8/27d85f4cddfd6cf6cf3f1ab217707fd11fc7932e7414315cb0b659e7799a02f7
- Page: https://openairdocs.org/service-documents/leonardo/sb-109-158/file/27d85f4cddfd

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Pa ge 1 of 24 
N°  109-158 
DA TE:  March 21, 2023 
REV. :  / - M arch 15, 2017 
TITLE 
ATA 64 – TAIL ROTOR HOUSING AND SLIDER GROUP DISASSEMBLY AND 
R
EASSEMBLY 
REVISION LOG 
First Issue 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S.B. N°109-158 ALERT 
 DATE: March 21, 2023 
Page 2 of 24 REVISION: / 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
Part I: 
All A109C helicopters that have performed maintenance activities requiring the 
disassembly of the tail rotor duplex bearing housing after the helicopter delivery. 
Part II: 
All A109C helicopters. 
B. COMPLIANCE 
Part I: 
Within and not later than 100 (one hundred) flight hours or 6 (six) months, whichever 
occurs first, after the issue of this Service Bulletin. 
Part II: 
At each assembly of the tail rotor duplex bearing housing. 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin is issued in order to prescribe the disassembly and reassembly of 
the housing and slider assembly of the tail rotor rotating controls. 
E. DESCRIPTION 
There have been reported cases of ring-nut tighten loss, likely as a result of poor 
maintenance tasks accomplishment of the assembly instructions for the tail rotor 
housing and slider group. 
In order to minimize the likelihood of occurrence of potential human errors during 
maintenance, LH updated the maintenance instructions in order to provide additional 
guidelines, including a better identification Vital Points (VP) for the assembly of the tail 
rotor duplex bearing support. 
As such, this Service Bulletin requires (Part I) to perform the installation of the tail rotor 
duplex bearing housing following the IETP updated instructions and (Part II) requires to 
follow such updated instructions whenever the TR duplex bearing housing is assembled. 
During the procedure, the operator must obey the Local Regulations applicable to the 
Vital Points.

### Page 3

S.B. N°109-158 ALERT 
DATE: March 21, 2023 
REVISION: / Page 3 of 24 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA nr. 
EASA.21.J.005. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness Directives. 
G. MANPOWER 
To comply with this Service Bulletin, the following MMH are deemed necessary: 
Part I: 8 (eight). 
Part II: N.A. 
MMH are based on hands-on time and can change with personnel and facilities available. 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
1) PUBLICATIONS 
SECTION/PARAGRAPH DESCRIPTION PART 
PAR01 00-20-1 Helicopter Safety I 
PAR02 64-00-12 Tail rotor hub and blades 
assembly – Removal/Installation 
I 
PAR03 64-30-3 Pitch change mechanism – 
Removal/Installation 
I, II 
2) ACRONYMS & ABBREVIATIONS 
AMDI Aircraft Material Data Information 
MM Maintenance Manual 
DOA Design Organization Approval 
IETP Interactive Electronic Technical Publications 
EASA European Aviation Safety Agency 
LH Leonardo Helicopters 
PTUM Pictorial Tools Usage Manual 
MMH Maintenance Man Hours 
P/N Part Number 
S/N Serial Number 
3) ANNEX 
Annex A MM Section 64-30 Rev. 5

### Page 4

S.B. N°109-158 ALERT 
 DATE: March 21, 2023 
Page 4 of 24 REVISION: / 
J. PUBLICATIONS AFFECTED 
N.A. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 5

S.B. N°109-158 ALERT 
DATE: March 21, 2023 
REVISION: / Page 5 of 24 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
N.A. 
2) CONSUMABLES 
Refer also to AMDI for the consumable materials required to comply with the MM 
Paragraphs referenced in the accomplishment instructions. 
3) LOGISTIC MATRIX 
N.A. 
B. SPECIAL TOOLS 
Refer to PTUM for the special tools required to comply with the MM Paragraphs 
referenced in the accomplishment instructions. 
C. INDUSTRY SUPPORT INFORMATION 
N.A.

### Page 6

S.B. N°109-158 ALERT 
 DATE: March 21, 2023 
Page 6 of 24 REVISION: / 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
have been removed to gain access to the 
modification area and adequately protect them until 
their later re-use. 
b) Shape the cables in order to prevent interference 
with the structure and the other existing installations, 
using where necessary suitable lacing cords and 
plastic cable tiedown. 
PART I 
1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe 
maintenance. Disconnect the battery, all electrical power sources and/or the external 
power supply. 
2. In accordance with MM Paragraph 64-00-12, remove from the helicopter the tail rotor hub 
and blades assembly. 
3. In accordance with MM Paragraph 64-30-3, remove the tail rotor pitch change mechanism. 
4. In accordance with MM Paragraph 64-30-3, disassemble the tail rotor housing and slider 
assembly. 
NOTE 
Vital Point (VP): the point of a component, assembly or 
installation, where incorrect assembly or an undetected 
error could cause the loss of rotorcraft and/or fatalities. 
5. In accordance with MM Paragraph 64-30-3 Rev. 5 (R ef. Leonardo WebPortal or Annex A 
of this Service Bulletin), assemble the tail rotor housing and slider assembly. 
6. In accordance with MM Paragraph 64-30-3, install the tail rotor housing and slider 
assembly. 
7. In accordance with MM Paragraph 64-00-12, install on the helicopter the tail rotor hub and 
blades assembly. 
8. Return the helicopter to a ready to flight condition and record for compliance with Part I of 
this Service Bulletin on the helicopter logbook. 
9. Send the attached compliance form to the following mail box: 
engineering.support.lhd@leonardo.com

### Page 7

S.B. N°109-158 ALERT 
DATE: March 21, 2023 
REVISION: / Page 7 of 24 
As an alternative, gain access to My Communications section on Leonardo WebPortal and 
compile the “Service Bulletin Application Communication”.

### Page 8

S.B. N°109-158 ALERT 
 DATE: March 21, 2023 
Page 8 of 24 REVISION: / 
PART II 
NOTE 
Vital Point (VP): the point of a component, assembly or 
installation, where incorrect assembly or an undetected 
error could cause the loss of rotorcraft and/or fatalities. 
1. During the application of any maintenance operati on requiring the assembly of the TR 
duplex bearing housing, it is required to perform the relevant assembly procedure in 
accordance with MM Paragraph 64-30-3 Rev. 5 (Ref. Leonardo WebPortal or Annex A of 
this Service Bulletin) or later published issues. 
2. Record for compliance with Part II of this Service Bulletin on the helicopter logbook. 
3. Send the attached compliance form to the following mail box: 
engineering.support.lhd@leonardo.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal and 
compile the “Service Bulletin Application Communication”. 
 
  Non cancellare mai questo segnalibro Non cancellare mai interruzione sezione 

### Page 9

ANNEX A 
S.B. N°109-158 ALERT 
DATE: March 21, 2023 
REVISION: / Page 9 of 24 
 
 
 
 
ANNEX A 
MM SECTION 64-30 REV. 5

### Page 10 (OCR)

LEONARDO
ANNEX A  HELICOPTERS
A109C-MM
- MAINTENANCE
MANUAL
A109C
HELICOPTER
MODEL
THIS 2nd ISSUE ENTIRELY SUPERSEDES ISSUE 1 DATED 26th SEPTEMBER 1994 INCLUDING
REVISION 15 DATED 14" JULY 2010
Second Issue:  15th March 2013
Revision:  No. 5 - 10th March 2023
THIS PUBLICATION IS ISSUED BY LEONARDO S.p.A.
This document contains proprietary data and information and shall not be disclosed, reproduced in whole or in part for any purpose, other
than helicopter operation or maintenance, without prior written authorization from LEONARDO S.p.A.
PUBLICATION CODE 502052101
S.B. N°109-158 ALERT
DATE: March 21, 2023
Page 10 of 24  REVISION: /

### Page 11 (OCR)

ANNEX A  * LEONARDO  HELICOPTERS
A109C-MM
SECTION 64-30
PITCH CHANGE MECHANISM
64-30-1. DESCRIPTION
The pitch change mechanism, mounted on the 90° gearbox, consist of a sleeve sliding on the 90° output shaft, connected
to the tail rotor blades by a slider and two pitch links, and to the control pedals by links and levers.
The components of the pitch change mechanism are shown in figure 64-17.
64-30-2. MAINTENANCE
64-30-3. Removal/installation
(Fig 64-17)
A. Input Conditions:
(1) Required conditions:
- Helicopter safe for maintenance (Chap 00).
- Access panels P6 and P12 removed (Sect 06-40).
- Tail rotor hub and blade assembly removed (Sect 64-00).
(2) Support equipment:
Tool, T/R pitch change slider ring nut removal/installation (LSE NO 9).
- Tool, T/R pitch change housing ring nut removal/installation (LSE NO 10).
- Tool, T/R pitch change housing duplex bearing removal (LSE NO 11).
- Tool, T/R pitch change housing duplex bearing installation (LSE NO 12).
- Tool, T/R pitch change slider installation (LSE NO 13).
- Tool, T/R duplex bearing removal (LSE NO 17).
- Syringe (Local supply).
- Heating gun (Local supply).
- Feeler gage (Local supply)
- Depth micrometer gage (Local supply).
- Refrigerator (Local supply).
(3) Consumable materials:
Rev. 5  641
S.B. N°109-158 ALERT
DATE: March 21, 2023
REVISION: /  Page 11 of 24

### Page 12 (OCR)

ANNEX A  * LEONARDO  HELICOPTERS
A109C-MM
WARNING: THE CONSUMABLE MATERIALS THE NOMENCLATURE OF WHICH IS PREFIXED BY "D)"
ARE DANGEROUS MATERIALS. BEFORE USE, MAKE SURE TO KNOW THE SAFETY PRECAU-
TIONS AND FIRST AID INSTRUCTIONS PRINTED ON:
- THE LABEL ON THE CONTAINER THE MATERIAL WAS SUPPLIED IN
- THE MATERIAL SAFETY DATA SHEET
- THE LOCAL SAFETY REGULATIONS.
ALSO MAKE SURE THAT THE APPLICABLE FIRST AID MATERIALS ARE AVAILABLE.
Abrasive paper No 300 or 400 (LCM NO 6).
(D) MEK (Methyl-ethy 1-ketone) (LCM NO 9).
(D) Retaining compound (LCM NO 19).
- (D) Grease (LCM NO 22).
- (D) Primer (LCM NO 23).
Safety wire (LCM NO 24).
(D) Lubricating oil (LCM NO 25).
(D) Adhesive (LCM NO 29).
(D) Corrosion inhibiting compound (LCM NO 40).
(D) Corrosion inhibiting compound (LCM NO 41).
(D) Primer (LCM NO 34).
Safety wire (LCM NO 36).
(D) Solvent, cleaning (LCM NO 37).
Soft lint-free cloth (Local supply).
(4) Other recommendations:
WARNING: THIS INSTALLATION INCLUDES VITAL POINTS (VP). DURING THE PROCEDURE, YOU MUST
OBEY THE LOCAL REGULATIONS APPLICABLE TO THE VITAL POINTS.
CAUTION: MAKE SURE THAT YOU DO NOT MIX GREASES OF DIFFERENT BRANDS ALTHOUGH THE
SPECIFICATIONS ARE THE SAME
REFER TO THE HELICOPTER LOG BOOK TO PREVENT MIXTURE OF UNWANTED GREASES.
CAUTION: THIS COMPONENT INCLUDES CRITICAL PARTS. EXAMINE THE COMPONENT FOR SIGNS OF  STRUCTURAL DAMAGE, BEFORE YOU INSTALL IT ON THE HELICOPTER REFER TO SECT
20-60.
64-2  Rev. 5
S.B. N°109-158 ALERT
DATE: March 21, 2023
Page 12 of 24  REVISION: /

### Page 13 (OCR)

ANNEX A  K LEONARDO  HELICOPTERS
A109C-MM
(i) Cut the lock wire, in two places, then, with the wrench (2, figure 64-17C) part of the tool (LSE NO 10),
remove the ring nut (5, figure 64-17A).
NOTE: Items 1, 3 and 4 of figure 64-17D are part of the tool (LSE NO 17).
(i) Put the duplex bearing housing (2) on the support (1).
NOTE: To help remove the duplex bearing (4, figure 64-17A) from the duplex bearing housing (3) a light heating of the
extemal part of the duplex bearing housing with a heating gun is permitted. The temperature must not be more
than 90° C. To prevent damage to the duplex bearing do not apply hot air directly on the duplex bearing boots.
(k) Put the two adapters (3 and 4, figure 64-17D) on the duplex bearing housing (2) then with an applicable
press remove the duplex bearing (4, figure 64-17A) from the duplex bearing housing (3).
(10) Remove boot (39).
(11) Remove attaching parts of levers (5 and 49), then remove levers and shims (8) and extract pivot (9) from lugs
on gearbox.
(12) Disconnect lever (40) from link (46) by removing attaching parts, remove lever (40). Discard cotter pin.
(13) Disconnect link (46) from lugs on gearbox by removing attaching parts; remove link (46). Discard cotter pin.
C. Installation Procedure.
(1) Position pivot (9, fig 64-17) in 90° gearbox lugs.
(2) Install laminated shims (8) and levers (5 and 49) on pivot (9). Do not torque attaching parts.
NOTE: If any of the following items: 90° gearbox case, pivot (8) levers (5 and 49) laminated shims (8) have been
replaced, proceed as follows:
(a) Position pivot (9) in 90° gearbox lugs.
(b) Position levers (5 and 49) on pivot (9) without shims and secure temporarily in position.
(c) Measure the total gap between one lever and the adjacent lug with a feeler gauge. Half of the gap is the
dimension of each laminated shim (8).
(d) Remove levers (5 and 49) from pivot (9).
(e) Fit laminated shims (8) on pivot (9) then reinstall levers (5 and 49) and secure. Do not torque nuts (3 and
51) at this time.
(f) Check for free rotation of pivot. If shim thickness is unsatisfactory, modify the shims the same amount on
either side to obtain an axial play between 0.03 to 0.08 mm between 90° gearbox lugs bearings and levers
NOTE: Before installing the boot in the housing and slider group deform the boot metallic rim to an oval shape with a
maximum diameter of 43 thru 44 mm (1.693 thru 1.732 in) as shown in DETAIL C of Fig 64-17. This is to help
a tighter fit in the seat. Put the inboard boot in its position in the housing and slider group.
(3) Position boot (39) on gearbox shaft.
(4) Reassemble housing (15) and slider assembly (23) as follows:
Rev. 1  647
S.B. N°109-158 ALERT
DATE: March 21, 2023
REVISION: /  Page 13 of 24

### Page 14 (OCR)

ANNEX A  K LEONARDO  HELICOPTERS
A109C-MM
CAUTION: BEFORE YOU ASSEMBLE THE HOUSING AND SLIDER GROUP (1, FIG. 64-17E), PUT THE COM-
PONENT THAT FOLLOW AND THE RELATED ATTACHING PARTS ON AN APPLICABLE
WORK TABLE.
CAREFULLY EXAMINE THE COMPONENT AND THE RELATED ATTACHING PARTS FOR
CORROSION, NICKS AND DAMAGE, WEAR AND FRETTING. IF YOU FIND THAT THE COMPO-
NENT IS DAMAGED, REPLACE IT.
- THE DUPLEX BEARING (4)
- THE HOUSING (5).
(a) Divide the two parts of the duplex bearing (4).
NOTE: Do Step C. (4)(b) thru Step C. (4)(d) only for removed bearings. New bearings are supplied already lubricated and
must not be filled with grease.
(b) Fill the Syringe (Local supply) with the Grease (LCM NO 22).
(c) Before you install the bearing (8), fill it with 3.5 cc (0.21 in?) of grease with the syringe from the side
opposite to the boot. Refer to Detail A of Fig. 64-17E.
(d) Do Step C. (4)(c) again on the bearing (9).
(e) Put the bearing (8) against the bearing (9) with the boot sides externally and the internal and external V-
marks aligned to show an arrow. See Detail A, Fig. 64-17E.
(f) Install the duplex bearing (4) into the housing (5) in the way that follows:
1. Apply a thin layer of Primer (LCM NO 23) on the mating surfaces between the duplex bearing (4) and
housing (5).
2. Put the housing (5) on the Base (10), part of the tool (LSE NO 12).
WARNING: BE CAREFUL WHEN YOU USE HEAT. HOT PARTS CAN CAUSE INJURY TO THE PERSONS.
ALWAYS USE APPLICABLE PROTECTIVE CLOTHING.
Heat the housing (5) to a temperature between 60 and 70 °C with the Heating gun (Local supply).
This will help you to install the duplex bearing (4) into the housing. Make sure that the temperature is
not more than 90 °C (heating gun set to a temperature of 90 °C).
NOTE: As an alternative to heating the housing (5); you can cool down the duplex bearing (4) with the Refrigerator
(Local supply) to a temperature between -18 and -40 °C for 30 minutes. Do not touch the cold duplex bearing
with bare hands to prevent injury.
4. Push the duplex bearing (4) into the housing (5). To do this, use the Pin (11), part of the tool (LSE NO
12) and an applicable arbor press.
5. Make sure there is no clearance between the two bearings (8 and 9) and between the outer ring of
duplex bearing (4) and the shoulder of the housing (5). To do this, use the applicable Feeler gage
(Local supply).
6. Remove the housing-bearing assembly (12) from the base (10).
NOTE: Before you continue, make sure that all the components are at ambient temperature.
(g) Install the ring nut (3) into the housing-bearing assembly (12). Obey the instructions that follow:
1. Clean the threads of the ring nut (3) and the housing (5) with the Cloth, soft lint-free (Local supply)
and the Solvent, cleaning (LCM NO 37). (VP)
64-8  Rev. 5
S.B. N°109-158 ALERT
DATE: March 21, 2023
Page 14 of 24  REVISION: /

### Page 15 (OCR)

ANNEX A  K LEONARDO  HELICOPTERS
A109C-MM
2. Dry the threads of the ring nut (3) and the housing (5) with a clean Cloth, soft lint-free (Local supply).
(VP)
3. Apply a layer of Primer (LCM NO 34) on the threads of the ring nut (3).
4. Apply a layer of Primer (LCM NO 34) on the threads of the housing (5).
Apply four drops of Sealing compound (LCM NO 19) on the threads of the ring nut (3). Put them in
four equally spaced positions (90 degrees apart). (VP)
6. Lock the Base (14), part of the tool (LSE NO 10) in an applicable vice.
7. Put the housing-bearing assembly (12) on the base (14), then lock it with the two Bolts (13), part of
the tool (LSE NO 10).
. Install the ring nut (3) in the housing-bearing assembly (12) with the Wrench (15), part of the tool
(LSENO 10).
9. Torque the ring nut (3) to 118 thru 127 Ni (87 thru 94 1bf ft). (VP)
10. Make sure that the duplex bearing (4) turns freely. (VP)
11. Refer to Detail B of Fig. 64-17E
Measure and record the dimension L.
b. Make sure that the dimension you find is between 23.75 to 24.0 mm (0.935 to 0.945 in).
c.  If you find that the dimension is not in the given limits, remove the duplex bearing (4). Then, do
Step C. (4)(f) and Step C. (4)(g) again.
12. Refer to Detail C of Fig. 64-17E.
a. Measure and record the dimension M.
b. Calculate and record the dimension N with this formula: N = M - L
NOTE: The safety wire must be installed with the double-twist method and put in tension. Example of an acceptable
safety wire installation is shown in Detail B1 of Fig. 64-17E. As a general approach, an "o" angle between 60°
and 120° is adviseable.
14. Safety the ring nut (3) to the housing (5) with the new Safety wire (LCM NO 36) in two places as
shown in Detail B1 of Fig. 64-17E. Refer also to Section 20-10. (VP)
(h) Apply a thin layer of Oil (LCM NO 25) on the internal surface of the duplex bearing (4).
(i) Put the Bushing (18), part of the tool (LSE NO 13) in its position on the Pin (19), part of the tool (LSE NO
13).
(i) Put the housing group (16) on the pin (19) above the bushing (18).
(k) Put the slider (2) on the pin (19).
Rev. 5  649
S.B. N°109-158 ALERT
DATE: March 21, 2023
REVISION: /  Page 15 of 24

### Page 16 (OCR)

K LEONARDO
ANNEX A  HELICOPTERS
A109C-MM
NOTE: To help you install the slider (2), heat the housing group (16) in an oven preheated to a temperature of 50 °C for
15 to 30 minutes.
As an alternative to heating the housing group (16); you can cool down the slider (2) with the Refrigerator
(Local supply) to a temperature between -18 and -40 °C for 30 minutes. Do not touch the cold slider with bare
hands to prevent injury.
(1) Push the slider (2) into the housing group (16). To do this, use the Barrel (17), part of the tool (LSE NO 13)
and an applicable arbor.
(m) Remove the housing-slider assembly (20) from the pin (19).
NOTE: Before you continue, make sure that all the components are at ambient temperature.
(n) Make sure there is no clearance between the inner rings of the two bearings (8 and 9) and the shoulder of
the slider (2). To do this, use the applicable Feeler gage (Local supply).
(o) Refer to Detail D of Fig. 64-17E:
1. Measure and record the dimension N. To do this, use an applicable Depth micrometer gage (Local
supply).
2. Make sure that the dimension N measured agrees with the dimension calculated at Step C. (4)(g) 12.b.
3. If you find that the dimension N does not agree, remove the duplex bearing (4). Then, do Step C. (4)(1)
and Step C. (4)(o) again.
(p) Lock the Base (22), part of the tool (LSE NO 9) in an applicable vice.
(q) Put the housing-slider assembly (20) on the base (22).
(r) Move the braces (23) of the slider against the pins (24) of the base (22). Refer to Detail E of Fig. 64-17E.
(s) Clean the threads of the ring nut (6) and the slider (2) with the Cloth, soft lint-free (Local supply) and the
Solvent, cleaning (LCM NO 37). (VP)
(t) Dry the threads of the ring nut (6) with a clean Cloth, soft lint-free (Local supply). (VP)
(u) Apply a layer of Primer (LCM NO 34) on the threads of the ring nut (6).
(v) Apply a layer of Primer (LCM NO 34) on the threads of the slider (2).
(w) Apply four drops of Sealing compound (LCM NO 19) on the threads of the ring nut (6). Put them in four
equally spaced positions (90 degrees apart). (VP)
(x) Install the ring nut (6) with the Wrench (21), part of the tool (LSE NO 9).
(y) Torque the ring nut (6) to 49 thru 59 Nm (36 thru 43 1bf ft). (VP)
(z) Remove the housing and slider group (1) from the base (22).
(aa) Install the new Lock ring (7).
(ab) Bend the clawed tabs of the lock ring (7) on the ring nut (6). Make sure that the two clawed tabs of the lock
ring (7) are correctly engaged.
(5) Connect lever (40) and links (10) to housing (15) Torque nuts to 3,4-4,5 Nm, then install cotter pins.
64-10  Rev. 5
S.B. N°109-158 ALERT
DATE: March 21, 2023
Page 16 of 24  REVISION: /

### Page 17 (OCR)

· LEONARDO
ANNEX A  HELICOPTERS
A109C-MM
1. Support
2. Duplex bearing housing
3. Adapter
4. Adapter
A6CD814A
Figure 64-17D. T/R Pitch change housing duplex bearing removal
Rev. 1  6417
S.B. N°109-158 ALERT
DATE: March 21, 2023
REVISION: /  Page 17 of 24

### Page 18 (OCR)

K LEONARDO
ANNEX A  HELICOPTERS
A109C-MM
1. Housing and slider group  16. Housing group
2. Slider  17. Barrel (Part of the LSE NO 13)
3. Ring nut  18. Bushing (Part of LSE NO 13)
4. Douplex bearing  19. Pin (Part of LSE NO 13)
5. Housing  20. Housing-slider assembly
6. Nut  21. Wrench (Part of LSE NO 9)
7. Lock ring  22. Base (Part of LSE NO 9)
8. Bearing  23. Brace
9. Bearing  24. Pin
10. Base (Part of LSE NO 12)
11. Pin (Part of LSE NO 12)
12. Housing-bearing assembly
13. Bolt (Part of LSE NO 10)
14. Base (Part of LSE NO 10)
15. Wrench (Part of LSE NO 10)
EXTERNA
/-MARK (REF
VIERNA  BORE SIDE
V-MARK (REF
NTERN
-MARK (REF
INTERNAL
BOOT SIDE  SIDE
(REF)
A6CD815B
Figure 64 17E (sheet 1 of 5). Housing and slider group
64-18  Rev. 5
S.B. N°109-158 ALERT
DATE: March 21, 2023
Page 18 of 24  REVISION: /

### Page 19 (OCR)

· LEONARDO
ANNEX A  HELICOPTERS
A109C-MM
A6CD816B
Figure 64 17E (sheet 2 of 5). Housing and slider group
Rev. 5  64-19
S.B. N°109-158 ALERT
DATE: March 21, 2023
REVISION: /  Page 19 of 24

### Page 20 (OCR)

ANNEX A  · LEONARDO  HELICOPTERS
A109C-MM
HOUSE BEARING
ASSY
SAFETY WIRE _
- SAFETY WIRE
SAFETY WIRING SCHEME OF RING NUT
Figure 64-17E (sheet 3 of 5). Housing and slider group
64-20  Rev. 5
Page 20 of 24

### Page 21 (OCR)

A LEONARDO
ANNEX A  HELICOPTERS
A109C-MM
20
18
A6CD818B
Figure 64 17E (sheet 4 of 5). Housing and slider group
Rev. 5  6421
S.B. N°109-158 ALERT
DATE: March 21, 2023
REVISION: /  Page 21 of 24

### Page 22 (OCR)

ANNEX A  · LEONARDO  HELICOPTERS
A109C-MM
E
20
23
24
22
ROTATION SENSE
23
22
24 -
Figure 64 17E (sheet 5 of 5). Housing and slider group
64-22
Page 22 of 24

### Page 23 (OCR)

ANNEX A  * LEONARDO  HELICOPTERS
A109C-MM
Figure 64-17F. Deleted
Figure 6417G. Deleted
Figure 64-17H. Deleted
Figure 64-18. Deleted
Figure 6419. Deleted
64-30-8. Housing grease fittings - replacement
(Fig 64-17)
A. Input Conditions:
(1) Required conditions:
- Helicopter safe for maintenance (Chap 00).
- Housing removed (Para 64-30-3).
(2) Support equipment:
Punch (local supply).
Small tap hammer (local supply).
- Arbor press (local supply).
(3) Consumable materials:
WARNING: THE CONSUMABLE MATERIALS THE NOMENCLATURE OF WHICH IS PREFIXED BY I (D)"
ARE DANGEROUS MATERIALS.
BEFORE USE, MAKE SURE TO KNOW THE SAFETY PRECAUTIONS AND FIRST AID INSTRUC-
TIONS PRINTED ON:
- THE LABEL ON THE CONTAINER THE MATERIAL WAS SUPPLIED IN
- THE MATERIAL SAFETY DATA SHEET
- THE LOCAL SAFETY REGULATIONS.
ALSO MAKE SURE THAT THE APPLICABLE FIRST AID MATERIALS ARE AVAILABLE.
- Cleaner, alkaline (LCM NO 38).
Conversion coating (LCM NO 39).
(4) Other recommendations: None.
B. Remove the two grease fittings (1, Fig 64-20) of the housing (2) in the way that follows:
(1) Put the housing (2) on a clean and flat working surface in a well-lit work area.
CAUTION: DO NOT DAMAGE THE INTERNAL WALL OF THE HOUSING (2) DURING THE GREASE FIT-
TINGS (1) REMOVAL.
NOTE: To prevent housing (2) damage, it is recommended to insert the punch into the grease fittings (1).
(2) Gently remove the grease fittings (1) with an applicable punch and small hammer. Push from the inside to the
outside of the housing (2).
(3) Do a visual inspection for integrity of the housing bores, the grease fittings and of the surrounding surface. If
you find damage contact the Design Authority.
(4) Clean the housing bores with cleaning compound (LCM NO 38).
Rev. 5  6423
S.B. N°109-158 ALERT
DATE: March 21, 2023
REVISION: /  Page 23 of 24

### Page 24 (OCR)

ANNEX A  K LEONARDO  HELICOPTERS
A109C-MM
(5) Apply the chemical conversion coating (LCMINO 39) on the repair area of the housing bores.
C. Install the two grease fittings (1) of the housing (2) in the way that follows:
(1) Gently push the grease fittings (1) into the housing (2) with an arbour press from the outside to the inside, up to
the touch surface. Make sure you insert the grease fittings parallel to the housing bore axis.
(2) Make sure that the grease fittings (1) are correctly installed and that no damage occurred to the grease fittings
and to the housing during installation.
A6CD855A
2 Fitting  Housing
Figure 64-20. Housing grease fittings - replacement
64-24  Rev. 2
S.B. N°109-158 ALERT
DATE: March 21, 2023
Page 24 of 24  REVISION: /

### Page 25

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
