# Leonardo Alert Service Bulletin 119-094: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-0837; AD 2021-20-18 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 119-094](https://openairdocs.org/service-documents/leonardo/sb-119-094.md)
- Title as filed: Leonardo Helicopters ASB No. 119-094
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/fe/b2/feb2f0816bfb4248853755ebf4e1a5de38da84f50177cded4ccf67958e08068f
- Page: https://openairdocs.org/service-documents/leonardo/sb-119-094/file/feb2f0816bfb

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N° 119-094
DATE:  November 15, 2018 
REV. :  / - March 3, 2017 
Page 1 of 10 
TITLE
ATA 56 - LEFT AND RIGHT PASSENGERS CABIN DOORS WINDOW BONDING. 
REVISION LOG 
New Issue 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S.B. N°119-094 
 DATE: November 15, 2018 
Page 2 of 10 REVISION: / 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
Leonardo AW119MKII helicopters S/N 14831, 14834, 14838, 14840, 14841, 14842, 
14843, 14844, 14901, 14904, 14905, 14906 and 14918. 
B. COMPLIANCE 
Within and not later than 100 flight hours or 6 months since the date of issuance of this 
Service Bulletin, whichever occurs first. 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin provides the necessary instructions to restore the passengers' 
cabin window bonding in accordance with the approved design data. 
E. DESCRIPTION 
During the replacement of a passengers' cabin window of an AW119MKII, the 
maintenance personnel have found difficulties in the window removal. 
The investigation concluded that the gasket was bonded to the window (or on both 
sides) instead of to the door frame and that this configuration could be present on a 
batch of helicopters. 
Due to this, Leonardo Helicopters issues this Service Bulletin in order to remove the 
standard windows installed on the affected helicopters and to reinstall them in 
accordance with the approved design data. 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on

### Page 3

S.B. N°119-094 
DATE: November 15, 2018 
REVISION: / Page 3 of 10 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin six (6) (MMH) are deemed necessary. 
Maintenance-Man-Hours are based on hands-on time and can change with personnel 
and facilities available 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE DESCRIPTION 
DM01 00-20 Helicopter on ground for a safe maintenance. 
2) ACRONYMS 
AMDI Aircraft Material Data Information 
DOA Design Organization Approval 
EASA European Aviation Safety Agency 
LHD Leonardo Helicopter Division 
MMH Maintenance Man Hour 
MMIR Maintenance Malfunction Inspection Report 
N.A. Not Applicable 
SB Service Bulletin 
P/N Part Number 
PTUM Pictorial Tool Usage Manual 
3) ANNEX 
N.A. 
J. PUBLICATIONS AFFECTED 
A119 / AW119 MKII Maintenance Manual. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 4

S.B. N°119-094 
 DATE: November 15, 2018 
Page 4 of 10 REVISION: / 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
1 999-1700-48-101G - Rubber gasket 6 m - - - 
2 999-1700-49-101G - Rubber seal filler 6 m - - - 
2) CONSUMABLES 
# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 
3 199-05-152 TY I, CL 2 (AW code: 900003249) Adhesive RTV732 AR (1) - 
4 Solvent 
(AW code: 505405407) 
Ardrox 5503 AR (1) - 
5 CCC-C-46 
(AW code: 590210190) 
Soft Lint-Free Cloth AR (1) - 
6 Commercial (AW code: 590220125) Masking tape AR (1) - 
 
Refer also to AMDI for the consumable materials required to comply with the 
Maintenance Manual DM referenced in the accomplishment instructions. 
NOTE 
(1) Item to be procured as local supply. 
B. SPECIAL TOOLS 
The following special tools, or equivalent, are necessary to accomplish this Service 
Bulletin: 
# P/N DESCRIPTION Q.TY NOTE PART 
7 3G5605G00132 TOOL KIT, WINDOWS INSTL 1 (B1) - 
 
Refer also to PTUM for the special tools required to comply with the Maintenance 
Manual DM referenced in the accomplishment instructions. 
SPECIAL TOOLS NOTE 
 Please contact Leonardo Helicopters Division order administration to request the (B1)
tools supply on loan. As soon as the present Service Bulletin is implemented the 
tools supplied on loan shall be promptly returned to Leonardo Helicopters 
Division.

### Page 5

S.B. N°119-094 
DATE: November 15, 2018 
REVISION: / Page 5 of 10 
C. INDUSTRY SUPPORT INFORMATION 
Owners/Operators who comply with the instructions of this Service Bulletin no later 
than the applicable date in the “Compliance” section will be eligible to receive 
REQUIRED MATERIALS on free of charge basis, except for Consumable Materials 
and Special Tools.  
NOTE: Customers who fail to comply with the instructions in this Service Bulletin 
before the compliance date are not eligible for the aforementioned special policy.  
Please Issue relevant MMIR form to your Warranty Administration Dpt.

### Page 6

S.B. N°119-094 
 DATE: November 15, 2018 
Page 6 of 10 REVISION: / 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Replace the hardware found damaged during the 
following operation. 
b) Let adhesive and sealant cure at room temperature 
for at least 24 hours unless otherwise specified. 
c) At the end of the rework operations, remove all the 
used tools and completely remove any working 
residual using a suitable air cleaner. 
d) All lengths are in mm. 
e) Refer to CSRP-A-CSRP- 00-X for the applicable 
structural standard practice procedures. 
1. In accordance with Maintenance Manual Section 00-20 prepare the helicopter on ground 
for a safe maintenance. Disconnect the battery, all electrical power sources and/or the 
external power supply. 
2. With reference to Figure 1 , proceed in the rework of the left passengers cabin door 
window installation as described in the following procedure: 
2.1 With reference to Figure 1, pull the strap assy P/N A487A002A and remove the 
seal filler P/N 109- 0361-72-111 from the gasket P/N 109-0361-72-113. Discard 
the seal filler and keep the strap assy for later reuse.  
2.2 Hold the left window P/N 109- 0821-34-105 or P/N 109-0822-68-137 externally to 
make sure that it does not fall down. 
2.3 Carefully push the window P/N 109- 0821-34-105 or P/N 109- 0822-68-137 
outboard. 
2.4 Remove and discard the gasket P/N 109- 0361-72-113 from the window or from 
the passengers' cabin door structure. 
2.5 If necessary, remove the rubber particles from the window or from the 
passengers' cabin door structure with the plastic scraper. Clean the seal seat on 
the window and from the passengers' cabin door structure with a soft lint-free 
cloth and the cleaning solvent Ardrox 5503. Dry the cleaned area with a clean 
cloth. 
2.6 Cut the rubber gasket P/N 999 -1700-48-101G at a length of 2700 mm to obtain 
the new gasket P/N 109-0361-72-113. 
2.7 Cut the rubber seal filler P/N 999- 1700-49-101G at a length of 2700 mm to obtain 
the new seal filler P/N 109-0361-72-111.

### Page 7

S.B. N°119-094 
DATE: November 15, 2018 
REVISION: / Page 7 of 10 
CAUTION 
Surfaces to be bonded shall be clean, dry and free of 
oil or grease. 
2.8 Clean the internal tight groove of the gasket P/N 109- 0361-72-113 and the 
gasket seat on the door structure with a soft lint-free cloth  and the cleaning 
solvent Ardrox 5503. Dry the cleaned area with a clean cloth. 
NOTE 
The tight groove of the gasket P/N 109-0361-72-113 
engages the door structure as per Figure 1  
section A-A. 
NOTE 
Make sure that there is no clearance between the two 
ends of the gasket. 
2.9 With reference to Figure 1 section A-A and Detail Gasket, install the gasket  
P/N 109-0361-72-113 on the window frame of the left door structure with the filler 
seal groove facing inboard. The joint line of the gasket must be positioned as 
shown in Figure 1. 
CAUTION 
Perform the operation carefully to avoid damaging the 
gasket. 
2.10 Install the left window P/N 109-0821-34-105 or P/N 109- 0822-68-137 by means 
of a suitable plastic scraper, in the gasket P/N 109- 0361-72-113 previously 
installed on the window frame of the door structure. 
2.11 Apply the masking tape along the entire perimeter of the door structure near th e 
gasket P/N 109- 0361-72-113 to prevent the same from being soiled with 
adhesive in the subsequent operation. 
WARNING 
DO NOT APPLY ADHESIVE BETWEEN GASKET 
AND THE LOWER CORNER RADIUS OF THE DOOR 
STRUCTURE AS PER FIGURE 1. 
2.12 With reference to Figure 1, on the internal side of the passengers' cabin door, 
bond the edges of the door structure in the groove of the gasket  
P/N 109- 0361-72-113 by means of the 199- 05-152 TY I CL 2 adhesive. Make 
sure to apply the correct quantity of the adhesive in the groove of the gasket. Do 
not let the adhesive squeeze out of the gasket.

### Page 8

S.B. N°119-094 
 DATE: November 15, 2018 
Page 8 of 10 REVISION: / 
2.13 If the window P/N 109-0821-34-105 or P/N 109-0822-68-137 is dirty, immediately 
clean the dirty area with a clean cloth. 
NOTE 
Do not pull the seal filler to try to make its installation 
easier. If you pull it, the seal filler contour gets a 
deformation. The deformation of the filler wedge 
contour decreases the seal strength. 
NOTE  
Do not torque the seal filler when you install it along 
the curved parts of the seal. 
NOTE 
The strap assy P/N A487A002A must be located in the 
upper part of the gasket (Ref. Figure 1). 
2.14 Install the seal filler P/N 109- 0361-72-111 as described in the following 
procedure: 
2.14.1 With reference to Figure 1 section A-A, insert the seal filler  
P/N 109- 0361-72-111 into the buttonhole of the strap assy  
P/N A487A002A. 
2.14.2 Keep one end of the seal filler P/N 109- 0361-72-111 in its position with 
the thumb. The joint line of the seal filler must be positioned exactly as 
shown in Figure 1. 
2.14.3 Carefully put the seal filler P/N 109- 0361-72-111 in the related groove 
of the gasket P/N 109- 0361-72-113 by hand and tool kit 
3G5605G00132. 
2.14.4 Make sure that there is no clearance between the two ends of the seal 
filler P/N 109-0361-72-111.  
2.14.5 With reference to Figure 1 section A- A, lock the strap assy  
P/N A487A002A to the stud P/N MS27980-17B. 
WARNING 
DO NOT APPLY ADHESIVE BETWEEN GASKET 
AND THE LOWER CORNER RADIUS OF THE DOOR 
STRUCTURE AS PER FIGURE 1. 
2.15 With reference to Figure 1, on the external side of the passengers' cabin door, 
bond the edges of the door structure in the groove of the gasket  
P/N 109- 0361-72-113 by means of the 199- 05-152 TY I CL 2 adhesive. Make

### Page 9

S.B. N°119-094 
DATE: November 15, 2018 
REVISION: / Page 9 of 10 
sure to apply the correct quantity of the adhesive in the groove of the gasket. Do 
not let the adhesive go off from the gasket. 
2.16 If the window P/N 109- 0821-34-105 or P/N 109-0822-68-137 is dirty, immediately 
clean the dirty area with a clean cloth. 
2.17 Remove the masking tape from the passengers' cabin door structure. 
3. Repeat steps from 2.1 to 2.17 on the right passengers ’ cabin door window  
P/N 109-0821-34-106 or 109-0822-68-138. 
4. Return the helicopter to a ready to flight conditio n and record for compliance with this 
Service Bulletin on the helicopter logbook. 
5. Send the attached compliance form to the following mail box: 
 aw109.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 10

Figure 1 
 S.B. N°119-094 
 DATE: November 15, 2018 
Page 10 of 10 REVISION: /

### Page 11

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
