# Agusta Bollettino Tecnico 119-22: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2008-0327, the docket of AD 2008-14-05. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Agusta Bollettino Tecnico 119-22](https://openairdocs.org/service-documents/leonardo/sb-119-22.md)
- Title as filed: U.S. DOT/FAA - Agusta BT 119-22
- Pages: 20
- PDF: https://openairdocs.org/files/sha256/0d/2b/0d2bd89d166610faeee00e1d989f1b6ed68fe2e2e0ee0f6c4874910097e5d939
- Page: https://openairdocs.org/service-documents/leonardo/sb-119-22/file/0d2bd89d1666

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

Via Giovanni Agusta, 520
AGUSTA  Tel.: +39 0331-229111 - Fax: +39 0331-229605/222595  21017 Cascina Costa di Samarate (VA) Italy
AN AGUSTAWESTLAND COMPANY
TRANSLATION OF
BOLLETTINO TECNICO  N 119-22
The technical content of this document is approved  DATE July 11, 2007
under the authority of DOA nr EASA.21J.005.
REV.
Compliance with  MANDATORY
this bollettino is:
SUBJECT:INSPECTION AND REPLACEMENT OF THE HYDRAULIC LINES
P/N 109-0761-64-103 AND 109-0761-65-103 BY MEANS OF THE KIT
P/N 109-0824-03-101 APPLICATION
REASON: Avoid the possible interference between the hydraulic lines P/N 109-
0761-64-103 and 109-0761-65-103, of the No° 1 hydraulic system, and
tail rotor control rod assy P/N 109-0032-01-41.
HELICOPTERS AFFECTED:
All the Agusta A119 helicopters up to S/N 14028 included.
COMPLIANCE:
PARTI
Within the next 50 (fifty) flight hours and successively periodically repeat
the inspection each 100 (one hundred) flight hours up to the compliance
of PART I^
PART I^
Within and not later than July 31, 2008.
DESCRIPTION:
Cases of interference between hydraulic line P/N 109-0761-65-103 and
the tall rotor control rod assy have been reported on some A109 series
helicopters.
The interference during the normal flight operations can produce wear of
hydraulic lines with the subsequent loss of hydraulic fluid.
The A119 helicopters are potentially subject to the same type of
malfunction because constructively and functionally similar in subject
area.
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Page 1 of 17

### Page 2 (OCR)

B.T. 119-22
To avoid the above, two new hydraulic lines P/N 109-0763-96-101 and
P/N 109-0763-97-101 have been produced, that coupled with a new
mounting method, allow an increase in clearance between lines and tail
rotor control rod assy.
This Bollettino is issued in order to provide:
- Inspection requirements  (PART I^), for interference, until the
compliance of the PART II^ of this Bollettino;
- the necessary instructions for the Kit P/N 109-0824-03-101 installation
(PARTI).
REQUIRED MANPOWER:
The following estimated manpower hours are required for compliance
with this Bollettino:
PART 1^: 2 (two).
PART I|^: 16 (sixteen).
WARRANTY:
The parts required to apply the present Bollettino shall be supplied on a
free of charge basis by Agusta upon request, except for the consumable
Upon application of this Bollettino, Customers are requested to submit to
Agusta Warranty Administration the Technical Bulletin Compliance form
attached to this Bollettino duly completed in all its parts.
REQUIRED MATERIALS:
The following materials are required for compliance with this Bollettino:
PART I^:
N.A.
PART I^:
PART NUMBER  DENOMINATION  Q.TY
109-0824-03-101  Hydraulic line tail rotor servo actuator
retrofit kit
109-0763-96-101  Hydraulic line assy
109-0763-97-101  Hydraulic line assy
AN3-22A  Bolt  . 1
MS21042L3  Self-locking nut  .. 1
AS21919WDG04  Clamp
AS21919WDG05  Clamp  . 1
NAS1149D0332K  Washer  . 1
NAS43DD3-36N  Spacer  .2
NAS43DD3-35N  Spacer  . 1
AN743Z13  Bracket  .2
AS5406D04  Fitting
999-8001-64-1  Sleeve  300 mm
NAS1738B4-2  Rivet
or:
CR3213-4-2  Rivet
Page 2 of 17

### Page 3 (OCR)

B.T. 119-22
In addition the following consumable materials are necessary
SPECIFICATION  DENOMINATION  Q.TY
TT-N-95  Aliphatic naphtha  A.R.
or:
PD-680 Type I|  Cleaning solvent  A.R.
MIL-P-23377  Epoxy polyamide primer  A.R.
(cod. 900004523)
MS20995C32E  Lockwire  A.R.
SPECIAL TOOLS:
N.A.
WEIGHT AND BALANCE CHANGES:
Negligible.
REFERENCES:
A119 Maintenance Manual.
A119 Rotorcraft Flight Manual.
PUBLICATIONS AFFECTED:
A119 Illustrated Parts Catalog.
COMPLIANCE INSTRUCTIONS:
GENERAL NOTES
> Unless otherwise specified retain all
parts that will be removed. Replace
damaged hardware.
> Place an identification tag on all
components  that are re-usable,
including the attaching hardware that
have been removed to gain access to
the modification area and adequately
protect them until their later re-use.
• Exercise extreme care during drilling
operations to prevent cables or hosing
damage.
> All dimensions are in mm.
Page 3 of 17

### Page 4 (OCR)

B.T. 119-22
> After the completion of structural work,
remove all shaving and sharp edges. If
necessary  re-apply  protective
treatment.
• Clean the areas that may have been
contaminated by hydraulic fluid or
engine oil using aliphatic naphtha.
PARTI
1.  Prepare the helicopter on ground for a safe maintenance,
disconnect any power supply.
N  Remove the main transmission upper forward fairing.
Gain access to inside box beam through lightening hole. Using
a mirror and a suitable light source, inspect the possible
interference area between the hydraulic lines and the tail rotor
control rod assy P/N 109-0032-01-41 (ref. figure 1).
CAUTION
During the visual inspection move several
times the pedals completely back and forth in
order to single out the least clearance point
or the possible presence of e interference.
NOTE
In case the displacing/removal of the sealant
seep protections is required, after the
inspection restore the protections.
4.  In case there is no interference between the hydraulic lines and
the tail rotor control rod assy, proceed as follows:
4.1.  Reinstall the main transmission upper forward fairing.
4.2.  Return the helicopter to a ready to flight condition.
4.3.  Record compliance with this PART of the Bollettino in the
helicopter log book.
4.4.  Repeat this PART (within the next 100 hours and subsequently
every 100 hours) until the compliance with PART II of this
Bollettino.
Page 4 of 17

### Page 5 (OCR)

B.T. 119-22
In case interference between the hydraulic lines and the tail
rotor control rod assy is reported, perform the PART II.
PART I^
1.  Prepare the helicopter on ground for a safe maintenance,
disconnect any power supply.
2.  Remove the upper forward fairing, open the left engine oil fan
compartment access doors.
3.  Disconnect the forward rod end of the droop compensator
control system linear actuator in accordance with instructions
provided in the A119 Maintenance Manual (ref. figure 2).
3.1.  Rotate Droop stop aft and secure.
Remove hydraulic lines P/N 109-0761-64-103 and 109-0761-
65-103 as follows:
4.1.  Remove mounting hardware of hydraulic lines P/N 109-0761-
64-103 and 109-0761-65-103 from the helicopter roof (ref.
figure 1).
4.2.  If installed, displace/remove the sealant seep deck protections.
4.3.  Remove the inspection panel P/N 109-0322-10-41, located on
LH box beam; retain hardware for later reuse.
4.4.  In order to facilitate hydraulic lines removal, remove the bracket
P/N 109-0761-25-5 mounting hardware, retain the hardware for
later reuse (ref figure 3).
4.5.  Disconnect hydraulic lines P/N 109-0761-64-103 and 109-0761-
65-103 from the relevant mount and withdraw them from the
helicopter box beam.
NOTE 1
Follow the HYDRAULIC POWER SYSTEMS
MAINTENANCE PRECAUTIONS related to
the hydraulic systems, reported in the A119
Maintenance Manual, chapter 29
NOTE 2
Adequately recover the drained oil from the
hydraulic lines.
Page 5 of 17

### Page 6 (OCR)

B.T. 119-22
NOTA 3
Plug all the disconnected hydraulic lines to
avoid oil spillage and contaminations.
Remove clamps that fix together the removed hydraulic lines
and retain hardware for later reuse.
In case during the inspection (PART I^) interference between
hydraulic lines and the tail rotor control rod assy has been
reported, or damage of the hydraulic lines in the area of
possible interference with the tail rotor control rod assy have
been reported, perform the following procedure (from step 5.1.
to step 5.19.).
5.1.  Remove the left access door P/N 109-0322-10-13 and open the
left upper servicing platform D9 (ref. A119 Maintenance Manual
chapter 6).
5.2.  Remove line P/N 109-0680-14-101 from the solenoid valve P/N
109-0711-09-103 in accordance with A119 Maintenance
Manual (ref. figures 4 and 5).
5.3.  Remove clamp P/N AS21919WDG32 or MS21919WDG32
(whichever is installed) as shown in figure 5.
5.4.  Remove clamps located on the ducts P/N 6050501245 or
NAS1375A08SM196 (whichever is installed) and shown in
figure 5, move the connecting hose P/N 109-0680-11-101 to
gain access to the junction area.
5.5.  Remove line P/N 109-0680-14-101, note the locking system in
order to reproduce it during the installation phase (ref. figure 5).
CAUTION
During removal, pay particular attention to
not damage the ring P/N NAS595.
5.6.  In order to facilitate the tail rotor control rod removal, it is
allowed to remove the exhaust duct of the engine oil cooler fan
P/N 109-0620-90-101.
5.7.  Disconnect rod assy P/N 109-0032-08 or P/N 109-0040-55
(whichever is installed) from the bellcrank P/N 109-0040-35 in
accordance with A119 Maintenance Manual (ref. figure 6).
5.8.  Disconnect tail rotor control rod assy P/N 109-0032-01-41 in
accordance with A119 Maintenance Manual.
Page 6 of 17

### Page 7 (OCR)

B.T. 119-22
CAUTION
Do not change the tail rotor control rod assy
length during reinstallation.
5.9.  In order to avoid tail rotor control rod assy damage, adequately
protect the engine bay support rib lightening hole.
5.10.  Withdraw tail rotor control rod assy through the door P/N 109-
0322-10-41 hole.
NOTE
It is allowed to reuse the removed control rod
when, after the inspection as per the A119
Maintenance Manual, only when within the
limits provided in the Manual.
Be sure not to change the tail rotor control
rod assy length during the repair procedure.
5.11.  If a damaged tail rotor control rod assy is found annotate the
total length and replace it with a new rod assy in accordance
with A119 Maintenance Manual.
5.12.  Place tail rotor control rod assy in its position through door P/N
109-0322-10-41 hole.
5.13.  Install tail rotor control rod assy P/N 109-0032-01-41 in
accordance with A119 Maintenance Manual.
CAUTION
If the tail rotor control rod assy length is
unchanged, adjustment of flight controls is
not required.
5.14.  Install rod  assy P/N 109-0032-08 or P/N 109-0040-55
(whichever is removed) to bellcrank P/N 109-0040-35 in
accordance with A119 Maintenance Manual (ref. figure 6).
5.15.  Reconnect pipe P/N 109-0680-14-101 and relevant ring, and
lock as previously noted (ref. figure 5).
5.16.  Insert ducts P/N 6050501245 or NAS1375A08SM196
(whichever is installed) on hose P/N 109-0680-11-101 and
tighten the metallic clamps (ref. figure 5).
5.17.  Install pipe P/N 109-0680-14-101 at the solenoid valve P/N 109-
0711-09-103 in accordance with A119 Maintenance Manual (ref
figures 4 and 5).
Page 7 of 17

### Page 8 (OCR)

B.T. 119-22
5.18.  If removed, install exhaust duct of the engine oil cooler fan P/N
109-0620-90-101.
5.19.  Install the previously removed left access door P/N 109-0322-
10-13, close the left upper servicing platform D9 (ref. A119
Maintenance Manual chapter 6).
6.  Assemble together the brackets P/N AN743Z13 (as shown in
figure 7) using:
a)  Clamps P/N AS21919WDG04, AS21919WDG05;
b)  Bolt P/N AN3-22A, washers P/N NAS1149D0332K;
c)  N°  2  spacers P/N NAS43DD3-36N, and n°1
spacer P/N NAS43DD3-35N;
d)  Nut P/N MS21042L3.
In accordance with figure 7, using the fixing assy made at step
6, countermark and drill • 3,6 - 3,8 mm the beam and the
brackets.
Remove fixing assy made at step 6 and then remove the
bracket mount.
9.  Clean area from contaminates and debris and restore the
protective treatment using epoxy polyamide primer.
NOTE
Pay particular attention to avoid that the
shavings fall in box beam.
10.  Install brackets P/N AN743Z13, using n° 4 rivets P/N
NAS1738B4-2 as shown in figure 7.
11.  Install new hydraulic lines in accordance with the following
procedure:
11.1.  Install, as shown in figure 3, between hydraulic lines P/N 109-
0763-96-101 and P/N 109-0763-97-101 clamps removed from
lines P/N 109-0761-64-103 and 109-0761-65-103 using the
relevant hardware.
11.2.  pipe  P/N  109-0763-97-101,  install  sleeve
P/N 999-8001-64-1, between clamp and fitting as shown in
figure 3.
11.3.  Install and secure, using relevant hardware and fittings
hydraulic lines P/N 109-0763-96-101 and P/N 109-0763-97-101
as shown in figure 3.
Page 8 of 17

### Page 9 (OCR)

B.T. 119-22
NOTE
In case the connection between the hydraulic
P/N 109-0763-97-101 and line
P/N 109-0762-40-1 is difficult, it is possible to
replace fitting P/N AN815-4D,  already
installed, with fitting P/N AS5406D04.
11.4.  Install bracket P/N 109-0761-25-5 using relevant hardware (ref
figure 3).
11.5.  Secure, to box beam, the hydraulic lines P/N 109-0763-96-101
and P/N 109-0763-97-101 (as shown in figure 7) using:
a) Clamps P/N AS21919WDG04, AS21919WDG05;
b)  Bolt P/N AN3-22A, washers P/N NAS1149D0332K;
c)  N° 2  spacers P/N NAS43DD3-36N, and n°1
spacer P/N NAS43DD3-35N;
d)  Nut P/N MS21042L3.
CAUTION
Verify hydraulic lines P/N 109-0763-96-101
and P/N 109-0763-97-101 do not interfere
between themselves. It is allowed to use
clamps  P/N  AS21919WDG04,
AS21919WDG05 and relevant hardware to
space lines adequately.
12.  Gain access inside box beam through lighteing hole, using a
mirror and a suitable light source, verify that there is no
interference between the hydraulic lines P/N 109-0763-97-101,
109-0761-96-101 and the tail rotor control rod assy.
CAUTION
During visual inspection move pedals several
times completely back and forth in order to
be sure that there is no interference between
hydraulic lines and tail rotor control rod.
13.  Reinstall droop compensator control system linear actuator in
accordance with A119 Maintenance Manual (ref. figure 2).
14.  Bleed the n° 1 hydraulic system in accordance with A119
Maintenance Manual.
15.  Perform functional check of the n° 1 hydraulic system flight
controls in accordance with A119 Maintenance Manual, verify
that there is no leakage from the installed fittings
Page 9 of 17

### Page 10 (OCR)

B.T. 119-22
16.  If removed, perform linear actuator of the droop compensator
control system  adjustment in accordance with A119
Maintenance Manual and moreover verify its stroke.
17.  Reinstall inspection panel in its position on box beam, reusing
previously removed hardware.
18.  Restore sealant seep deck protections that may have been
removed at step 4.2.
19.  Install fairing and the doors previously removed. (ref. step 2)
20.  Perform operational check of heating system in accordance
with A119 Maintenance Manual
21.  Return the helicopter to a ready to flight condition.
22.  Record compliance with this PART of the Bollettino in the
helicopter log book.
Page 10 of 17

### Page 11 (OCR)

B.T. 119-22
FWD
Pipe assy
109-0761-64-103
Pipe assy
109-0761-65-103
TAIL ROTOR CONTROL ROD
AREA TO BE INSPECTED
TOP VIEW
REFERENCE ILLUSTRATION
FIGURE 1
Page 11 of 17

### Page 12 (OCR)

B.T. 119-22
• LINEAR ACTUATOR REF.
REFERENCE ILLUSTRATION
FIGURE 2
Page 12 of 17

### Page 13 (OCR)

B.T. 119-22
AS5406D04 Fitting (Ref.)
Pipe assy
109-0762-40-1 (Ref.)
Pipe assy
109-0762-41-1 (Ref.)
Pipe assy
109-0763-96-101
Pipe assy  Sleeve
109-0763-97-101  999-8001-64-1
Typ. 2 places
MS21919WDG4 Clamp (Ref.)  Bracket
MS21919WDG5 Clamp (Ref.)  109-0761-25-5 (Ref.)
AN3-12A Bolt (Ref.)
AN960JD10L Washer (2 OFF Ref.)
MS21042L3 Nut (Ref.)
REFERENCE ILLUSTRATION
FIGURE 3
Page 13 of 17

### Page 14 (OCR)

B.T. 119-22
USTRATION
FIGURE 4

### Page 15 (OCR)

B.T. 119-22
SOLENOID VALVE REF.
PROTECTION DUCT REF.
CLAMPS REF.
\AS21919WDG32 CLAMP REF.
• 109-0680-14-101 PIPE ASSY REF.
FITTING REF.
109-0680-11-101 CONNECTING HOSE REF.
REFERENCE ILLUSTRATION
FIGURE 5
Page 15 of 17

### Page 16 (OCR)

B.T. 119-22
Tail rotor control rod assy P/N 109-0032-01-41
Bellcrank
P/N 109-0040-35 (Ref.)
Rod assy
P/N 109-0032-08 (Ref.)
P/N 109-0040-55 (Ref:)
REFERENCE ILLUSTRATION
FIGURE 6
Page 16 of 17

### Page 17 (OCR)

B.T. 119-22
Install:
AN3-22A Bolt (1 OFF)  Install:
MS21042L3 Self locking nut (1 OFF)  NAS43DD3-35N Spacer (1 OFF)
AS21919WDG04 Clamp (1 OFF)  25.5
AS21919WDG05 Clamp (1 OFF)  TYP
NAS1149DO332K Washer (1 OFF)  NAS43DD3-36N Spacer (2 OFF)  109-0763-97-101  Pipe assy
too
Countermark and drill
Install:  • 3,6 - 3,8  109-0763-96-101  Pipe assy
AN743Z13 Bracket (2 OFF)
NAS1738B4-2 Rivet (4 OFF)
REFERENCE ILLUSTRATION
FIGURE 7
Page 17 of 17

### Page 18

(No text on this page.)

### Page 19 (OCR)

AGUSTA
AN AGUSTAWESTLAND COMPANY
Prego spedire a questo indirizzo:  Data:
Please send to the following address:  MODULO APPLICAZIONE BOLLETTINO TECNICO  Date:
TECHNICAL BULLETIN COMPLIANCE FORM
AGUSTA S.p.A.
VICE DIREZIONE GENERALE  Numero:
Number:
CUSTOMER SUPPORT
Via per Tornavento, 15
21019 Somma Lombardo (VA) - ITALY  Revisione:
Tel.: +39 0331 711100  Revision:
Fax: +39 0331 711397
Denominazione Cliente ed Indirizzo:  Telefono:
Customer Name and Address:  Telephone:
Fax:
Data Applicazione B.T.:
B.T. Compliance Date:
Modello Elicottero  Helicopter Model  S/N  Matricola  Tail Number  Total Hours  Ore Totali  Ore D.U.R.  T.S.O.
Note:
Remarks:
Informazioni:
Mod. AG AST 034 E 07  Information:
Al fine di gestire le varianti alla configurazione base, in relazione all'emissione del Bollettino Tecnico, preghiamo di voler compilare il presen-
te modulo in tutte le sue parti e spedirlo all'indirizzo sopra indicato. Si ringrazia per la gentile collaborazione data.
We request your cooperation in filling this form, in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address. We thank you beforehand for the information given.

### Page 20

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
