# Agusta Alert Bollettino Tecnico 119-38: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2010-0824; AD 2010-12-51 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Agusta Alert Bollettino Tecnico 119-38](https://openairdocs.org/service-documents/leonardo/sb-119-38.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin - Agusta BT No 119-038
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/02/13/0213848aef759322e9f032cfb492983380de9869a9f94b52cfc3ac49c1bec9ee
- Page: https://openairdocs.org/service-documents/leonardo/sb-119-38/file/0213848aef75

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

XX 
 
 
 
 
 
TRANSLATION OF  
BOLLETTINO TECNICO N°  119-38 
 
The technical content of this document is approved 
under the authority of DOA nr EASA.21J.005. DATE  March 25, 2010 
  
 REV.  xxxxxxx 
 
 
Compliance with 
this bollettino is: 
 
 
 
 
 
 
                    
                            ALERT Page 1 of 9 
 
SUBJECT:ONE-TIME INSPECTION OF THE 90° GEARBOX ASSY   
P/N 109-0440-06-103. 
 
REASON: Perform a one -time inspection  of the subject 90° gearbox to verify the 
presence of the bushing P/N 109 -0135-14-101 and provide the 
instructions to restore the correct configuration and for the re 
identification to P/N 109-0440-06-105. 
 
 HELICOPTERS AFFECTED: 
All the Agusta A119 and AW119MKII helicopters equipped with the 90° 
gearbox assy P/N 109 -0440-06-103 and all the 90° g earbox assy  
P/N 109-0440-06-103 at stock. 
 
COMPLIANCE: 
PART I^: 
Before the next flight from receipt of this Bollettino. 
 
PART II^: 
Within and not later than 5 (five) flight hours from receipt of this Bollettino 
and however within and not later than June 30, 2010 and however before 
the removal of the 90° gearbox inspected as per PART I^.  
 
DESCRIPTION: 
One case of missing bushing P/N 109 -0135-14-101 inside the 90° 
gearbox assy P/N 109-0440-06-103 output m ast, has been reported on 
an AW119MKII model helicopter. 
This Bollettino is issued in order to provide the necessary instructions to 
perform: 
PART I^:  a one -time inspection to verify the presence of the bushing   
P/N 109-0135-14-101 inside the 90° gearbox assy  P/N 109-0440-06-103 
 
    ALERT

### Page 2

B.T. 119-38 
 
 
 
Page 2 of 9 
 
output mast and, in case of absence , for the replacement of the gearbox  
and some parts of the tail rotor installation with the new 90° gearbox assy 
P/N 109-0440-06-105. 
PART II^: the 90° gearbox assy P/N 109-0440-06-103 re-identification to 
P/N 109-0440-06-105, in which the inspection has confirmed the bushing 
presence, by means of the installation of an additional nameplate.  
 
REQUIRED MANPOWER: 
The following estimated manpower hours are required for compliance 
with this Bollettino: 
PART I^: Negligible; 
PART II^: 1.5 (one and half). 
 
WARRANTY: 
The parts required to apply the present Bollettino shall be supplied on a 
free of charge basis by Agusta upon request except for the consumable 
items. 
Upon application of this Bollettino, Customers are requested to submit to 
Agusta Warranty Administration the Technical Bulletin Compliance form 
attached to this Bulletin duly completed in all its parts. 
 
REQUIRED MATERIALS: 
PART I^: 
The following materials could be required for compliance with PART I^ of 
this Bollettino: 
P/N    DENOMINATION   Q.TY 
109-0440-06-105 90° gearbox assy 1 
NAS1149C0463R Washer 3 
109-0135-02-101 T/R Control rod assy. 1 
109-0135-03-101 T/R Lever assy 1 
109-0135-05-101 T/R Half scissors assy 4 
109-0135-06-101 T/R Fitting assy 1 
109-0135-08-101 T/R Scissors sleeve 6 
NAS6604D22 Bolt 6 
 
In addition the following consumable material is necessary: 
 
SPECIFICATION DENOMINATION Q.TY 
TT-N-95 type 2  Aliphatic naphtha A.R. 
     (code 531055030)     
 
PART II^: 
The following material is required for compliance with PART I^ of this 
Bollettino: 
P/N    DENOMINATION   Q.TY 
A149A003A1 Nameplate 1

### Page 3

B.T. 119-38 
 
 
 
Page 3 of 9 
 
In addition the following consumable material is necessary: 
 
SPECIFICATION DENOMINATION Q.TY 
199-05-002   Adhesive EA934NA A.R. 
TY II CL 2   (code 900004603)     
TT-N-95 type 2  Aliphatic naphtha A.R. 
     (code 531055030)     
Commercial   Abrasive paper n. 220    A.R. 
     or equivalent 
Commercial  Masking tape A.R. 
 
SPECIAL TOOLS:  
N.A. 
 
WEIGHT AND BALANCE CHANGES:  
Negligible. 
 
REFERENCES: 
A119 / AW119MKII Maintenance Manual.  
 
PUBLICATIONS AFFECTED:  
N.A. 
 
COMPLIANCE INSTRUCTIONS: 
PART I^: 
(See figures 1÷2) 
 
1. Prepare the helicopter on ground for a safe maintenance, 
disconnect any power supply. 
 
2. Gain access to the tail rotor installation and with reference to 
figure 1, remove the forward boot P/N 109-0135-10 from the hub 
locking nut P/N 109-0135-12. 
 
NOTE 
If necessary clean the area to be inspected 
using a clean cloth dampened with aliphatic 
naphtha. 
 
3. With reference to figure  2, insert a 0.3 mm thickness gauge 
between the T/R control rod P/N 109-0135-02 and the hub 
locking nut  P/N 109 -0135-12 keeping the thickness gauge 
against  the T/R control rod assy P/N 109-0135-02. 
 
NOTE 
Use a thickness gauge that can be inserted 
between the control rod P/N 109-0135-02 
and the T/R hub l ocking nut   
P/N 109-0135-12.

### Page 4

B.T. 119-38 
 
 
 
Page 4 of 9 
 
 
3.1 If the thickness gauge goes in  for 5±1 mm the bushing  
P/N 109 -0135-14-101 is installed, return the fwd boot   
P/N 109-0135-10 in its initial position on the T/R hub l ocking nut 
P/N 109-0135-12 and perform steps 7. and 8.. 
 
NOTE 
In this case the 90° gearbox assy  
P/N 109 -0440-06-103 must be re -identified 
to P/N 109 -0440-06-105 performing the 
PART II^ within the compliance limits of this 
Bollettino. 
 
3.2 If the thickness gauge goes in for more than  6 mm the bushing 
P/N 109-0135-14-101 is not installed, proceed with the following 
steps. 
 
4. In accordance with the instructions given in the  
A119/AW119MKII Maintenance Manual from the helicopter 
remove: 
 T/R control rod P/N 109-0135-02; 
 T/R lever P/N 109-0135-03; 
 N. 4 T/R half scissors assy P/N 109-0135-05; 
 T/R fitting assy P/N 109-0135-06; 
 N. 6 T/R scissors sleeve P/N 109-0135-08; 
 N. 6 T/R sleeve connecting bolts P/N NAS6604D22; 
 The 90° gearbox assy P/N 109-0440-06-103. 
 
NOTE 
The removed parts must be sent to Agusta. 
 
5. In accordance with the instructions given in the  
A119/AW119MKII Maintenance Manual on the helicopter install 
the following efficient parts: 
 90° gearbox assy P/N 109-0440-06-105; 
 N. 6 T/R sleeve connecting bolts P/N NAS6604D22; 
 N. 6 T/R scissors sleeve P/N 109-0135-08-101; 
 T/R  fitting assy P/N 109-0135-06-101; 
 N. 4 T/R half scissors assy P/N 109-0135-05-101; 
 T/R lever P/N 109-0135-03-101; 
 T/R control rod P/N 109-0135-02-101. 
 
6. In accordance with the instructions given in the 
A119/AW119MKII Maintenance Manual perform the tail rotor 
dynamic balance. 
 
7. Return the helicopter in a ready to flight condition.

### Page 5

B.T. 119-38 
 
 
 
Page 5 of 9 
 
8. Record compliance with PART I^ of this Bollettino in the 
helicopter log book. 
 
NOTE 
The 90° gearbox assy P/N 109 -0440-06-
103 at stock must be visually inspected to 
verify the presence of the bus hing  
P/N 109-0135-14-101. 
If the bushing is  not installed the 90° 
gearbox shall be sent to Agusta. 
If the bushing is installed , the 90° g earbox 
must be re-identified in accordan ce with 
PART II^. 
 
 
PART II^: 
(See figure 3) 
 
1. Prepare the helicopter on ground for a safe maintenance, 
disconnect any power supply. 
 
2. In accordance with the instructions given in the A119/AW119MKII 
Maintenance Manual remove the fairing P12. 
 
3. Using an etch pen, on the 90° gearbox assy nameplate cross out  
the entire P/N 109-0440-06-103. 
 
4. With reference to figure 3, using a punch, write on the nameplate  
P/N A149A003A1: 
 
4.1 In the upper square write 109-0440-06-105. 
 
4.2 In the lower square write B.T. 119-38. 
 
5. On the  90° gearbox determine the area where to install the 
nameplate P/N A149A003A1 in pro ximity of the existing 
nameplate. 
 
6. Pre-fit the nameplate P/N A149A003A1 to ensure a tight fit with 
the 90° gearbox surface. 
 
7. On the 90° gearbox mask the area around the nameplate   
P/N A149A003A1 using masking tape. 
 
8. On the 90° gearbox  remove only the finish paint  from the 
nameplate P/N A149A003A1 installation area using abrasive 
paper n. 220 or finer grit. 
 
9. Rub the surface of the nameplate  P/N A149A003A1 to be 
bonded using abrasive paper n. 220 or finer grit.

### Page 6

B.T. 119-38 
 
 
 
Page 6 of 9 
 
 
10. Clean the repaired area with aliphatic naphtha. 
 
11. Mix the components of the adhesive EA934NA using a non -
metallic spatula and wait between 30 and 40 minutes before its 
use. 
 
12. Bond the nameplate P/N A149A003A1 on the 90° gearbox. Hold 
the nameplate in position by means of adhesive tape. 
 
NOTE 
After the bonding, all around the nameplate 
there should be evidence of adhesive 
squeeze-out; remove any excess adhesive. 
 
13. Leave adhesive to cure for 24 hours at ambient temperature. 
 
14. Remove the adhesive tape and restore the finish and the 90° 
gearbox painting scheme.  
 
15. In accordance with the instructions given in the A119/AW119MKII 
Maintenance Manual reinstall the fairing P12. 
 
16. Return the helicopter in a ready to flight condition. 
 
17. Record compliance with PART II^ of this Bollettino in the 
helicopter log book.

### Page 7

B.T. 119-38 
 
 
 
Page 7 of 9 
 
 
 
 
 
 
 
View A 
 
FIGURE 1 
109-0135-12 NUT 109-0135-10 FWD BOOT

### Page 8 (OCR)

B.T. 119-38
109-0135-02
CONTROL ROD ASSY
109-0135-12 NUT
0.30 mm THICKNESS GAUGE  109-0135-10 FWD BOOT
FIGURE 2
Page 8 of 9

### Page 9

B.T. 119-38 
 
 
 
Page 9 of 9 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
    FIGURE 3 
A149A003A1   
NAMEPLATE

### Page 10

(No text on this page.)

### Page 11

Note: 
Remarks: 
Informazioni: 
Information: 
 
Al fine di gestire le varianti alla configurazione base, in relazione all’emissione del Bollettino Tecnico, preghiamo di voler compilare il presen-
te modulo in tutte le sue parti e spedirlo all’indirizzo sopra indicato. Si ringrazia per la gentile collaborazione data.  
We request your cooperation in filling this form,  in order to  keep out statistical data relevant to aircraft configuration up- to-date. The form should be filled in all 
its parts and sent to the above address. We thank you beforehand for the information given. 
MODULO APPLICAZIONE BOLLETTINO TECNICO 
TECHNICAL BULLETIN COMPLIANCE FORM 
Data: 
Date: 
Numero: 
Number: 
Revisione: 
Revision: 
Prego spedire a questo indirizzo: 
Please send to the following address: 
 
AGUSTA S.p.A. 
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING DPT.
Via del Gregge, 100 
21015 Lonate Pozzolo (VA) - ITALY 
Tel.: +39 0331 664600 
Fax: +39 0331 664684
Telefono: 
Telephone: 
Fax: 
Data Applicazione B.T.: 
B.T. Compliance Date: 
Denominazione Cliente ed Indirizzo: 
Customer Name and Address: 
Modello Elicottero 
Helicopter Model S/N Matricola Tail Number Ore Totali Total Hours Ore D.U.R. T.S.O.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
