# Agusta Bollettino Tecnico 139-126: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2012-0886, the docket of AD 2014-03-01. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Agusta Bollettino Tecnico 139-126](https://openairdocs.org/service-documents/leonardo/sb-139-126.md)
- Title as filed: U.S. DOT/FAA - Agusta 139-126
- Pages: 7
- PDF: https://openairdocs.org/files/sha256/89/c1/89c1f4efbb766f2190d90712914cbecd8811c6fd970e1f27ab7b2cfc6448c6d3
- Page: https://openairdocs.org/service-documents/leonardo/sb-139-126/file/89c1f4efbb76

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

BOLLETTINO TECNICO N° 139-126 
 
The technical content of this document is approved 
under the authority of DOA nr. EASA.21J.005 DATE June 20, 2008  
 
 REV. / 
 
 
Compliance with 
this bulletin is: 
 
 
 
 
Page 1 of 5 
 
SUBJECT: WIRE STRIKE PROTECTION SYSTEM (WSPS) TOP CABLE CUTTER 
ASSY P/N 423-83001-1 REWORK 
 
REASON: to rework WSPS Top Cable Cutter Assy P/N 423-83001-1. 
 
HELICOPTERS AFFECTED: AB139/AW139 helicopters equipped with WSPS P/N 
4G9540F00211 and P/N 4G9540F00311 from S/N 31005 up to S/N 31131 (except S/N 
31007) and from S/N 41001 up to S/N 41013 (except S/N 41012). 
 
COMPLIANCE: within 200 flight hours from receipt of this Bollettino. 
 
NOTE 
If this Bollettino is not accomplished within the 
required compliance, WSPS Upper Installation P/N 
4G9540A00111 must be removed from the helicopter 
to continue flight operati ons until replacement of the 
Top Cable Cutter assy with a new or reworked one. 
See the following referenced AMP Data Modules to 
remove WSPS Upper Installation P/N 
4G9540A00111:

### Page 2

B.T. 139-126 
 
 
 
Page 2 of 5 
 
39-A-25-68-03-00A-520A-K Left strut aft fitting – 
Remove procedures 
39-A-25-68-04-00A-520A-K Right strut aft fitting – 
Remove procedures 
39-A-25-68-09-00A-520A-K Cross bar – Remove 
procedures 
 
DESCRIPTION: provide instructions to rework and shorten the WSPS Top Cable Cutter 
Assy P/N 423-83001-1, in order to increase the clearance between the WSPS and the 
main rotor blades. 
 
REQUIRED MANPOWER: it is estimated that in order to  accomplish this Bollettino three 
(3) man-hours are necessary. 
 
WARRANTY: N.A. 
 
REQUIRED MATERIALS: the following consumable materials are required for 
compliance with this Bollettino: 
 
SPEC./AW Code Number DESCRIPTION  Q.TY  NOTE  
MIL-DTL-81706, Cl. 1A, Form. I 
cod. 81110514 
Chemical conversion coating 
KP-XPF-1 (C061) 
AR Local supply
 
SPECIAL TOOLS: N.A. 
 
WEIGHT AND BALANCE CHANGES: N.A. 
 
REFERENCES: 
9 AW139  Aircraft Maintenance Publication (AMP) 
9 AW139  Aircraft Structural Repair Publication (ASRP) 
9 AW139  Material Data Information (AMDI)

### Page 3

B.T. 139-126 
 
 
 
Page 3 of 5 
 
PUBLICATIONS AFFECTED: 
9 AW139  Illustrated Parts Data (IPD) 
 
COMPLIANCE INSTRUCTIONS: 
1. Prepare the helicopter for a safe ground ma intenance. Disconnect the battery and all 
the electrical power sources and/or the external power supply. Refer to AMP, see data 
module n° 39-A-00-20-00-00A-120A-A. 
2. Remove the top cable cutter P/N 423-83001- 1. Refer to AMP, see data module n° 39-
A-25-68-06-00A-520A-K. 
WARNING 
OPERATIONS DESCRIBED AT STEP 3 MUST BE 
EXECUTED ONLY BY SKILLED STRUCTURAL OR 
MECHANICAL TECHNICIANS. 
3. In accordance with figure 1, rework t op cable cutter P/N 423-83001-1 as follows: 
3.1 Put the top cable cutter P/N 423-83001-1 on an applicable work bench. 
NOTE 
Tolerances of ± 0.7 mm are allowed for all 
measurements indicated in Figure 1 (i.e. cut lines, 
reference lines, diameters). 
NOTE 
The use of a local manufactured template to facilitate 
the operations (cut and hole location) is allowed. 
3.2 Trim the top cable cutter edge as shown in detail A.  
3.3 Perform a hole (nominal dia 4.8 mm) in the position indicated on Detail A. 
3.4 Protect the cut area wit h primer KP-XPF-1 (C061). Refer to ASRP (see DM n° 
39-A-51-61-03-00A-084A-A) for material application.

### Page 4

B.T. 139-126 
 
 
 
Page 4 of 5 
 
3.5 Restore paint as required. 
3.6 Mark BT 139-126 Rev./ on the reworked top cable cutter in a visible and 
permanent way. 
NOTE 
Top Cable Cutter for spare par ts or new build aircraft 
is identified by P/N 3G9506P01431. 
4. Install the top cable cutter reworked at step 3. Refer to AMP, see data module n° 39-
A-25-68-06-00A-720A-K. 
5. Return helicopter to flight  configuration and record for compliance of this Bollettino.

### Page 5

B.T. 139-126 
 
 
 
Page 5 of 5 
 
 
 
Figure 1 
NOTE: TOLERANCES OF ± 0.7 MM ARE 
ALLOWED FOR ALL MEASUREMENTS

### Page 6

(No text on this page.)

### Page 7

Note: 
Remarks: 
Informazioni: 
Information: 
 
Al fine di gestire le varianti alla configurazione base, in relazione all’emissione del Bollettino Tecnico, preghiamo di voler compilare il presen-
te modulo in tutte le sue parti e spedirlo all’indirizzo sopra indicato. Si ringrazia per la gentile collaborazione data.  
We request your cooperation in filling this form,  in order to  keep out statistical data relevant to aircraft configuration up- to-date. The form should be filled in all 
its parts and sent to the above address. We thank you beforehand for the information given. 
MODULO APPLICAZIONE BOLLETTINO TECNICO 
TECHNICAL BULLETIN COMPLIANCE FORM 
Data: 
Date: 
Numero: 
Number: 
Revisione: 
Revision: 
Prego spedire a questo indirizzo: 
Please send to the following address: 
 
AGUSTA S.p.A. 
PRODUCT SUPPORT ITALY 
Via per Tornavento,  15 
21019 Somma Lombardo (VA) - ITALY 
Tel.: +39 0331 711100 
Fax: +39 0331 711180
Telefono: 
Telephone: 
Fax: 
Data Applicazione B.T.: 
B.T. Compliance Date: 
Denominazione Cliente ed Indirizzo: 
Customer Name and Address: 
Modello Elicottero 
Helicopter Model S/N Matricola Tail Number Ore Totali Total Hours Ore D.U.R. T.S.O.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
