# AgustaWestland Bollettino Tecnico 139-368: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2014-0478; AD 2014-07-51 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [AgustaWestland Bollettino Tecnico 139-368](https://openairdocs.org/service-documents/leonardo/sb-139-368.md)
- Title as filed: U.S. DOT/FAA - AgustaWestland BT No 139-368
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/8d/88/8d8867e01aa20a8a57a1e98f275b71ff927ad019676be303e9a266009f664a0c
- Page: https://openairdocs.org/service-documents/leonardo/sb-139-368/file/8d8867e01aa2

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

BOLLETTINO TECNICO N° 139-368 
The technical content of this document is approved 
under the authority of DOA nr. EASA.21J.005 DATE March 19, 2014 
REV. / 
Compliance with 
this bulletin is: 
Page 1 of 9
SUBJECT: INSPECTION / REPLACEMENT OF LOWER HALF SCISSOR SPHERICAL 
BEARING P/N 3G6230V00654. 
REASON: to identify and replace potentially defective lower half scissor spherical 
bearings. 
HELICOPTERS AFFECTED: 
Part I: all AB139/AW139 helicopters installing MR Rotating Scissors P/N 
3G6230A00733 with S/N listed in Table 1 or repaired installing a lower half 
scissor spherical bearing P/N 3G6230V00654 with S/N listed in Table 2. 
Part II: all MR Rotating Scissors P/N 3G6230A00733 with S/N listed in Table 1 and all 
lower half scissor spherical bearing P/N 3G6230V00654 with S/N listed in Table 
2 and all MR Rotating Scissors P/N 3G6230A00733 repaired installing a lower 
half scissor spherical bearing P/N 3G6230V00654 with S/N listed in Table 2 , 
either installed or kept in stock. 
AgustaWestland S.p.A
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
T el.: +39 0331 229111 - Fax: +39 0331 229605/222595
MANDATORY
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
ALERT
ALERT

### Page 2

B.T. 139-368 
Page 2 of 9 
COMPLIANCE: 
Part I: within five (5 ) flight hours or one (1) week from receipt of this Bollettino Tecnico, 
whichever comes first, and then every five (5) flight hours up to accomplishment 
of Part II. 
Part II: within fifty (50) flight hours or thirty (30) days from receipt of this Bollettino 
Tecnico whichever comes first. 
DESCRIPTION: the supplier of the lower half scissor spherical bearing P/N 
3G6230V00654 has indicated a list of S/N that are potentially affected by a quality 
issue. Scope of this Bollettino Tecnico is to identify and replace potentially defective 
lower half scissor spherical bearings  in service establishing a tight interim inspection 
schedule to reduce the impact on aircraft operations in service. 
REQUIRED MANPOWER: it is estimated that, in order to accomplish this Bollettino 
Tecnico the following maintenance man-hours (MMH) are necessary: 
Part I: one (1) MMH; 
Part II: two (2) MMH. 
Man-hours are based on hands-on time and may vary with personnel and facilities 
available. 
WARRANTY: Owners/Operators who comply with the COMPLIANCE INSTRUCTIONS, 
no later than the applicable date in the “Compliance section”, will be eligible to 
receive replacements parts on a “free of charge basis”. 
NOTE: Customers who fail to comply with the instructions in this Bollettino Tecnico 
before the compliance date are not eligible for the aforementioned special policy. 
Issue relevant W.M.M. form ( (W)arranty Claim (M)aintenance Work Order 
(M)alfunction Report ) to your Warranty Administration Dpt.”

### Page 3

B.T. 139-368 
Page 3 of 9 
REQUIRED MATERIALS: the following materials, necessary to accomplish Part II of this 
Bollettino Tecnico, can be requested to AgustaWestland: 
P/N DESCRIPTION Q.TY Note 
3G6230V00654 Lower half scissors spherical bearing AR (1) 
Moreover the following consumable materials, or equivalent, are necessary to 
comply with this Bollettino Tecnico: 
Spec./AW code number DESCRIPTION Q.TY Note 
MIL-L-19537C Acrylic Lacquer (C081) AR Local supply 
Notes: 
(1) As an alternative to lower half scissor spherical bearings, MR rotating scissors  
P/N 3G6230A00733 may be supplied. 
Refer to AMDI for the consumable materials necessary to comply with the AMP data 
modules referenced in Part II of this Bollettino Tecnico. 
SPECIAL TOOLS: the following special tools are necessary to accomplish this 
Bollettino Tecnico: 
P/N DESCRIPTION Q.TY NOTES 
RMGE-DS-06-2010-LH or 
an approved alternative 
Platform (GG-01-00) 
AR 
(2) 
RMGE-DS-06-2010-RH or 
an approved alternative 
Platform (GG-02-00) 
Commercial Permanent black in felt pen Local supply 
Commercial Etch pen Local supply 
Notes: 
(2) Refer to Illustrated Tools and Equipment Publication (ITEP). See data modules 
39-A-GG-01-00-00A-066A-A and 39-A-GG-02-00-00A-066A-A. 
Refer to Illustrated Tools and Equipment Publication (ITEP) also for other special 
tools required to comply with the AMP data modules referenced in Part II of this 
Bollettino Tecnico.

### Page 4

B.T. 139-368 
 
 
 
Page 4 of 9 
 
WEIGHT AND BALANCE CHANGES: N.A. 
REFERENCES: 
 AW139 Aircraft Maintenance Data Information (AMDI) 
 AW139 Aircraft Maintenance Publication (AMP) 
 AW139 Illustrated Tools and Equipment Publication (ITEP) 
PUBLICATIONS AFFECTED: N.A. 
COMPLIANCE INSTRUCTIONS: 
Part I 
1. Prepare the helicopter for a safe ground maintenance. Disconnect the battery and all 
the electrical power sources and/or the external power supply.  Refer to AMP, see 
DM n° 39-A-00-20-00-00A-120A-A. 
2. Put the platforms (GG-01-00 and GG-02-00), or approved alternative s, adjacent to 
the left and to the right side of the fuselage, respectively. 
3. Open access door 473AL. Refer to AMP, see DM n° 39-A-06-41-00-00A-010A-A. 
4. With reference to Figure 1, get access to the MR  area and perform a general v isual 
inspection of the MR rotating scissors P/N 3G6230A00733 and an operational check 
for play and wear of the lower half scissors spherical bearing P/N 3G6230V00654  
(refer to section A-A), paying particular attention to the bearing staking condition; to 
do this manually move the bottom rotating scissors along the axis of the spherical 
bearing. 
4.1. If no unusual play and/or wear is detected , no further action is required. Go to 
step 5. 
4.2. If unu sual play and/or wear is detected, perform a detailed inspection for 
condition, damage and play of the MR  rotating scissors according to steps 9 
through 12.9 of AMP DM n° 39-C-62-31-00-00A-286C-A. 
4.2.1. If play is within limits, no further action is required. Go to step 5.

### Page 5

B.T. 139-368 
 
 
 
Page 5 of 9 
 
4.2.2. If play is beyond limits or wear is detected, report findings to AW139 
Product Support Engineering (aw139.mbx@agustawestland.com). 
5. Close access door 473AL. Refer to AMP, see DM n° 39-A-06-41-00-00A-010A-A. 
6. Remove the platforms from left and right sides of the fuselage. 
7. Return helicopter to flight configuration and record for compliance with Part I of this 
Bollettino Tecnico on the helicopter logbook. 
Part II 
1. Prepare the helicopter for a safe ground maintenance. Disconnect the batte ry and all 
the electrical power sources and/or the external power supply.  Refer to AMP, see 
DM n° 39-A-00-20-00-00A-120A-A. 
2. Put the platform (GG-01-00), or an approved alternative, adjacent to the left side of 
the fuselage. 
3. Open access door 473AL. Refer to AMP, see DM n° 39-A-06-41-00-00A-010A-A. 
NOTE 
As an alternative to the replacement of lower half 
scissor spherical bearing P/N 3G6230V00654 
described at following step 4 , it is allowed to replace  
MR rotating scissors according to AMP DM n° 39-C-
62-31-02-00A-520A-A / 39 -C-62-31-02-00A-720A-A 
installing new components not affected by this 
Bollettino Tecnico according to Table 1. 
Send the affected MR rotating scissors P/N 
3G6230A00733 (the ones removed or kept in stock) 
to AgustaWestland to perform the lower half scissor 
spherical bearing replacement and to mark the letter 
“R” after the S/N of the MR rotating scissor P/N 
3G6230A00733.

### Page 6

B.T. 139-368 
Page 6 of 9 
4. With reference to figure 1, get access to the MR rotating scissors area and  replace
the lower half scissor spherical bearing as described in the following procedure:
4.1. Remove and disassemble the MR rotating scissors. Refer to to AMP, see DM n° 
39-C-62-31-02-00A-520A-A / 39C-62-31-02-00A-530A-B. 
4.2. Replace affected lower half scissor spherical bearing P/N 3G6230V00654 
according to AMP DM n° 39-C-62-31-02-03A-920A-B. 
NOTE 
Discard all the affected lower half scissor spherical 
bearings P/N 3G6230V00654 with S/N as per Table 
2 removed at step 4.2. and kept in stock. 
4.3. Mark on MR lower scissor lever assy P/N 3G6230A00934 the letter “R” after th e 
S/N of the MR rotating scissor P/N 3G6230A00733. 
4.4. Mark the letter “R” on MR lower scissor P/N 3G6230A00934 by means of 
permanent black ink felt pen and apply Acrylic Lacquer (C081) or by means of 
etch pen. 
4.5. Assemble and install the MR rotating scissors. Refer to to AMP, see DM n° 39-
C-62-31-02-00A-710A-B / 39-C-62-31-02-00A-720A-A 
5. Close the access door 473AL. Refer to  AMP, see DM n°  39-A-06-41-00-00A-010A-
A.
6. Remove the platform from the left side of the fuselage.
7. Return helicopter to flight configuration a nd record for compliance with Part II of this
Bollettino Tecnico on the helicopter logbook  and mark the letter “R” after S/N on the
MR rotating scissor logcard.

### Page 7

B.T. 139-368 
 
 
 
Page 7 of 9 
 
 
 
 
 
Figure 1 
BETTER 
BETTER

### Page 8

B.T. 139-368 
 
 
 
Page 8 of 9 
TABLE 1 
MR Rotating Scissors P/N 3G6230A00733 affected S/N 
V1 
V2 
V3 
V4 
V5 
V7 
V8 
V9 
V10 
V11 
V12 
V13 
V14 
V15 
V16 
V17 
V18 
V19 
V20 
V21 
V22 
V23 
V24 
V25 
V26 
V27 
V28 
V29 
V30 
V31 
V32 
V33 
V34 
V35 
V36 
V37 
V38 
V39 
V40 
V41 
V42 
V43 
V44 
V45 
V46 
V47 
V48 
V49 
V50 
V51 
V52 
V53 
V54 
V55 
V56 
V57 
V58 
V59 
V60 
V61 
V62 
V63 
V64 
V65 
V66 
V67 
V68 
V69 
V70 
V71 
V72 
V73 
V74 
V75 
V76 
V77 
V78 
V79 
V80 
V81 
V82 
V83 
V84 
V85 
V86 
V87 
V88 
V89 
V90 
V91 
V92 
V93 
V94 
V95 
V96 
V97 
V98 
V99 
V100 
V101 
V102 
V103 
V104 
V105 
V106 
V107 
V108 
V109 
V110 
V111 
V112 
V113 
V114 
V115 
V116 
V117 
V118 
V119 
V120 
V121 
V122 
V123 
V124 
V125 
V126 
V127 
V128 
V129 
V130 
V131 
V132 
V133 
V134 
V135 
V136 
V137 
V138 
V139 
V140 
V141 
V142 
V143 
V144 
V145 
V146 
V147 
V148 
V149 
V150 
V151 
V152 
V153 
V154 
V155 
V156 
V157 
V158 
V159 
V160 
V161 
V162 
V163 
V164 
V165 
V166 
V167 
V168 
V169 
V170 
V171 
V172 
V173 
V174 
V175 
V176 
V177 
V178 
V179 
V180 
V181 
V182 
V183 
V184 
V185 
V186 
V187 
V188 
V189 
V190 
V191 
V192 
V193 
V194 
V195 
V196 
V197 
V198 
V199 
V200 
V201 
V202 
V203 
V204 
V205 
V206 
V207 
V208 
V209 
V210 
V211 
V212 
V213 
V214 
V215 
V216 
V217 
V218 
V219 
V220 
V221 
V222 
V223 
V224 
V225 
V226 
V227 
V228 
V229 
V230 
V231 
V232 
V233 
V234 
V235 
V236 
V237 
V238 
V239 
V240 
V241 
V242 
V243 
V244 
V245 
V246 
V247 
V249 
V250 
V251 
V252 
V253 
V254 
V255 
V256 
V257 
V258 
V259 
V260 
V261 
V262 
V263 
V264 
V265 
V266 
V267 
V268 
V269 
V270 
V271 
V272 
V273 
V274 
V275 
V276 
V277 
V278 
V279 
V280 
V281 
V282 
V283 
V284 
V285 
V286 
V287 
V288 
V289 
V290 
V291 
V292 
V293 
V294 
V295 
V302 
V303 
V304 
V305 
V432 
V433 
V434 
V435 
V436 
V437 
V438 
V439 
V440 
V441

### Page 9

B.T. 139-368 
 
 
 
Page 9 of 9 
TABLE 2 
Lower Half Scissor Spherical Bearing P/N 3G6230V00654 affected S/N 
KC1 
KC2 
KC3 
KC4 
KC5 
KC6 
KC7 
KC8 
KC10 
KC11 
KC12 
KC13 
KC14 
KC15 
KC16 
KC17 
KC18 
KC19 
KC20 
KC21 
KC22 
KC23 
KC24 
KC25 
KC26 
KC27 
KC28 
KC29 
KC30 
KC31 
KC32 
KC33 
KC34 
KC35 
KC36 
KC37 
KC38 
KC39 
KC40 
KC41 
KC42 
KC43 
KC44 
KC45 
KC46 
KC47 
KC48 
KC49 
KC50 
KC51 
KC52 
KC53 
KC54 
KC55 
KC56 
KC57 
KC58 
KC59 
KC10000 
KC10001 
KC10002 
KC10003 
KC10004 
KC10005 
KC10006 
KC10007 
KC10008 
KC10009 
KC10010 
KC10011 
KC10012 
KC10013 
KC10014 
KC10015 
KC10016 
KC10017 
KC10018 
KC10019 
KC10020 
KC10021 
KC10022 
KC10023 
KC10024 
KC10025 
KC10026 
KC10027 
KC10028 
KC10029 
KC10030 
KC10031 
KC10032 
KC10033 
KC10034 
KC10035 
KC10036 
KC10037 
KC10038 
KC10039 
KC10040 
KC10041 
KC10042 
KC10043 
KC10044 
KC10045 
KC10046 
KC10047 
KC10048 
KC10049 
KC10050 
KC10051 
KC10052 
KC10053 
KC10054 
KC10055 
KC10056 
KC10057 
KC10058 
KC10059 
KC10060 
KC10061 
KC10062 
KC10063 
KC10064 
KC10065 
KC10066 
KC10067 
KC10068 
KC10069 
KC10070 
KC10071 
KC10072 
KC10073 
KC10074 
KC10075 
KC10076 
KC10077 
KC10078 
KC10079 
KC10080 
KC10081 
KC10082 
KC10083 
KC10084 
KC10085 
KC10086 
KC10087 
KC10088 
KC10089 
KC10090 
KC10091 
KC10092 
KC10093 
KC10094 
KC10095 
KC10096 
KC10097 
KC10098 
KC10099 
KC10100 
KC10101 
KC10102 
KC10103 
KC10104 
KC10105 
KC10106 
KC10107 
KC10108 
KC10109 
KC10110 
KC10111 
KC10112 
KC10113 
KC10114 
KC10115 
KC10116 
KC10117 
KC10118 
KC10119 
KC10120 
KC10121 
KC10122 
KC10123 
KC10124 
KC10125 
KC10126 
KC10127 
KC10128 
KC10129 
KC10130 
KC10131 
KC10132 
KC10133 
KC10134 
KC10135 
KC10136 
KC10137 
KC10138 
KC10139 
KC10140 
KC10141 
KC10142 
KC10143 
KC10144 
KC10145 
KC10146 
KC10147 
KC10148 
KC10149 
KC10150 
KC10151 
KC10152 
KC10153 
KC10154 
KC10155 
KC10156 
KC10157 
KC10158 
KC10159 
KC10160 
KC10161 
KC10162 
KC10163 
KC10164 
KC10165 
KC10166 
KC10167 
KC10168 
KC10169 
KC10170 
KC10171 
KC10172 
KC10173 
KC10174 
KC10175 
KC10176 
KC10177 
KC10178 
KC10179 
KC10180 
KC10181 
KC10182 
KC10183 
KC10184 
KC10185 
KC10186 
KC10187 
KC10188 
KC10189 
KC10190 
KC10191 
KC10192 
KC10193 
KC10194 
KC10195 
KC10196 
KC10197 
KC10198 
KC10199 
KC10200 
KC10201 
KC10202 
KC10203 
KC10204 
KC10205 
KC10206 
KC10207 
KC10208 
KC10209 
KC10210 
KC10211 
KC10212 
KC10213 
KC10214 
KC10215 
KC10216 
KC10217 
KC10218 
KC10219 
KC10220 
KC10221 
KC10222 
KC10223 
KC10224 
KC10225 
KC10226 
KC10227 
KC10228 
KC10229 
KC10230 
KC10231 
KC10232 
KC10233 
KC10234 
KC10235 
KC10236 
KC10237 
KC10238 
KC10239 
KC10240 
KC10241 
KC10242 
KC10243 
KC10244 
KC10245 
KC10246 
KC10247 
KC10248 
KC10249 
KC10250 
KC10251 
KC10252 
KC10253 
KC10254 
KC10255 
KC10256 
KC10257 
KC10258 
KC10259 
KC10260 
KC10261 
KC10262 
KC10263 
KC10264 
KC10265 
KC10266 
KC10267 
KC10268 
KC10269 
KC10270 
KC10271 
KC10272 
KC10273 
KC10274 
KC10275 
KC10276 
KC10277 
KC10278 
KC10279 
KC10280 
KC10281 
KC10282 
KC10283 
KC10284 
KC10285 
KC10286 
KC10287 
KC10288 
KC10289 
KC10290 
KC10291 
KC10292 
KC10293 
KC10294 
KC10295 
KC10296 
KC10297 
KC10298 
KC10299 
KC10300 
KC10301 
KC10302 
KC10303 
KC10304 
KC10305 
KC10306 
KC10307 
KC10308 
KC10309 
KC10310 
KC10311 
KC10312 
KC10313 
KC10314 
KC10315 
KC10316 
KC10317 
KC10318 
KC10319 
KC10320 
KC10321 
KC10322 
KC10323 
KC10324 
KC10325 
KC10326 
KC10327 
KC10328 
KC10329 
KC10330 
KC10331 
KC10332 
KC10333 
KC10334 
KC10335 
KC10336 
KC10337 
KC10338 
KC10339 
KC10340 
KC10341 
KC10342 
KC10343 
KC10344 
KC10345 
KC10346 
KC10347 
KC10348 
KC10349 
KC10350 
KC10351 
KC10352 
KC10353 
KC10354 
KC10355 
KC10356 
KC10357 
KC10358 
KC10359 
KC10360 
KC10361 
KC10362 
KC10363 
KC10364 
KC10365 
KC10366 
KC10367 
KC10368 
KC10369 
KC10370 
KC10371 
KC10372 
KC10373 
KC10374 
KC10375 
KC10376 
KC10377 
KC10378 
KC10379 
KC10380 
KC10381 
KC10382 
KC10383 
KC10384 
KC10385 
KC10386 
KC10387 
KC10388 
KC10389 
KC10390 
KC10391 
KC10392 
KC10393 
KC10394 
KC10395 
KC10396 
KC10397 
KC10398

### Page 10

(No text on this page.)

### Page 11

Note: 
Remarks:
Informazioni: 
Information: 
Al f
ine di gestire le varianti alla configurazione base, in relazione all’emissione de l Bollettino Tecnico, preghiamo di voler compilare il presen-
te modulo in tutte le sue parti e spedirlo all’indirizzo sopra indicato. Si ringrazia per la gentile collaborazione data. 
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up- to-date. The form should be filled in all 
its parts and sent to the above address. We thank you beforehand for the information given.
MODULO APPLICAZIONE BOLLETTINO TECNICO 
TECHNICAL BULLETIN COMPLIANCE FORM
Data: 
Date:
Numero: 
Number:
Revisione: 
Revision:
Prego spedire a questo indirizzo: 
Please send to the following address: 
AGUSTAWESTLAND  S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING DPT.
Via del Gregge, 100 
21015 Lonate Pozzolo (VA) - ITALY 
Tel.: +39 0331 664905 
Fax: +39 0331 664684
Telefono: 
Telephone:
Fax:
Data Applicazione B.T.: 
B.T. Compliance Date:
Denominazione Cliente ed Indirizzo: 
Customer Name and Address:
Modello Elicottero 
Helicopter Model S/N Matricola Tail Number Ore Totali Total Hours Ore D.U.R. T.S.O.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
