# Leonardo Alert Service Bulletin 139-450: Revision C

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2020-0283; AD 2021-23-22 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 139-450](https://openairdocs.org/service-documents/leonardo/sb-139-450.md)
- Title as filed: Leonardo Helicopters ASB No. 139-450 Rev C
- Pages: 58
- PDF: https://openairdocs.org/files/sha256/3b/f2/3bf2445cb83dd4df860172b9b879194374b8edc3d8a25e5aa9e094ba0c293f15
- Page: https://openairdocs.org/service-documents/leonardo/sb-139-450/file/3bf2445cb83d

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N° 1 39-450
DA TE:  April 20, 2016 
REV. :  C - April 10, 2018 
Pag
e 1 of 57 
TITLE 
ATA 62 -
 MAIN ROTOR DAMPER INSPECTIONS 
REVISION LOG 
Present revision C is issued to remove from the effectivity of this Service Bulletin MR 
damper P/N 3G6220V01353, because it is no more subject to the inspections herein 
described. The maintenance program applicable to MR damper P/N 3G6220V01353 has 
been reported in AMPI Chapter 5 Issue 15. 
Revision A introduced an Eddy current inspection as valid alternative to the ones already 
prescribed with the first issue and limited the checks on the body end up to 1200 FH while 
for body ends having logged more than 1200 FH since new a more stringent inspection 
program was provided in Service Bulletin 139-452.  
Revision B was issued to introduce new MR damper P/N 3G6220V01353, fitting the new 
body end P/N M006-01H046-041. 
Revision bars in the outer margin identify changes. 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 2 of 57 REVISION: C - April 10, 2018 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
NOTE 
This Service Bulletin cancels and supersedes BT 139-
41
0 Rev. A and BT 139-446. 
Part I: all MR dampers P/N 3G6220V01351 and P/N 3G6220V01352 installed on 
A
B139 / AW139 helicopters (except S/N 31004, S/N 31007 and S/N 41237). 
 all MR dampers P/N 3G6220V01351, P/N 3G6220V01352 kept in stock that 
have logged three hundred (300) FH or more since new.  
Part II: all MR dampers that have been already inspected according to Part I and that 
have replaced the rod end assy with a component P/N M006-01H004-041 or 
P/N M006-01H004-045 or P/N M006-01H004-053 not marked as per Service 
Bulletin 139-450 figure 7. 
Part III: all body ends P/N M006-01H002-041 or P/N M006-01H002-047 and rod ends 
P/N M006-01H004-041 or P/N M006-01H004-045 or P/N M006-01H004-053, 
part of MR dampers P/N 3G6220V01351 and P/N 3G6220V01352 installed on 
AB139 / AW139 helicopters (except S/N 31004, S/N 31007 and S/N 41237). 
Part IV: all body ends P/N M006-01H002-041 or P/N M006-01H002-047 and rod ends 
P/N M006-01H004-041 or P/N M006-01H004-045 or P/N M006-01H004-053, 
part of MR dampers P/N 3G6220V01351 and P/N 3G6220V01352 installed on 
AB139 / AW139 helicopters (except S/N 31004, S/N 31007 and S/N 41237). 
Part V: all MR dampers P/N 3G6220V01351 and P/N 3G6220V01352 up to S/N 
MCR8086 included, that are installed on AB139 / AW139 helicopters (except 
S/N 31004, S/N 31007 and S/N 41237) and have accumulated less than 600 
FH since new. 
Part VI: all AB139 / AW139 helicopters (except S/N 31004, S/N 31007 and S/N 41237) 
equipped with MR dampers P/N 3G6220V01351 and P/N 3G6220V01352. 
Part VII: all MR dampers P/N 3G6220V01351 and all MR dampers P/N 3G6220V01352 
up to S/N MCR8764 (included) having rod end P/N M006-01H004-041 or -045 
or -053, except MR dampers listed in table 1 of Annex A and MR dampers 
marked with “BT 139 -446 Part II” or “BT 139 -446 Part III” on the logcard, 
installed on AB139 / AW139 helicopters (except S/N 31004, S/N 31007 and 
S/N 41237). 
 all MR dampers P/N 3G6220V01351 and P/N 3G6220V01352 that have 
removed the damper rod end assy in accordance with AMP procedure before

### Page 3

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 3 of 57 
the issuance of BT 139-446, even if they have S/N higher than MCR8764 or 
they are listed in table 1 of Annex A. 
Part VIII: all MR dampers P/N 3G6220V01351 and all MR dampers P/N 3G6220V01352 
up to S/N MCR8764 (included) having rod end assy P/N M006-01H004-041 or 
-045 or -053, except MR dampers listed in table 1 of Annex A and MR 
dampers marked with “BT 139 -446 Part II” or “BT 139- 446 Part III” on the 
logcard, kept in stock. 
NOTE 
MR damper ends marked as per figure 7 are not 
a
ffected by part I and part II of this Service Bulletin. 
NOTE 
The MR damper exact S/N may be composed of either 
f
our or five digits, possibly preceded by letters MCR 
and/or followed by letters A and/or B. For the purpose 
of the present instructions, only valid numerical 
characters are considered, neglecting “MCR”, “A”, “B” 
and initial zeros. 
Possible examples follow: 
 S/N 0272 will be referred to as S/N 272; 
 S/N 00344AB will be referred to as S/N 344; 
 S/N MCR1848A will be referred to as S/N 1848; 
 S/N MCR07568 will be referred to as S/N 7568; 
 S/N MCR10755 will be referred to as S/N 10755; 
MAG confirms that no duplicates exist in the valid 
numerical digits of item serialization (that means that 
only one among S/N 715, S/N MCR0715, S/N 
MCR00715 or S/N MCR0715AB exists).

### Page 4

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 4 of 57 REVISION: C - April 10, 2018 
B. COMPLIANCE 
NOTE 
Rod end and body end time since new or since 
ov
erhaul can be computed based on 
removal/installation data recorded on MR damper 
logcard Section 2. 
Part I: 
 
within thirty (30) FH since receipt of this Service Bulletin or at first MR damper 
removal, whichever comes first, on MR dampers that have logged three 
hundred (300) FH or more since new. 
 within thirty (30) FH since receipt of this Service Bulletin or when they reach 
three hundred (300) FH since new, whichever occurs later, on MR dampers that 
have not already logged three hundred (300) FH. 
 before next installation on the helicopter for MR dampers kept in stock that have 
logged three hundred (300) FH or more since new. 
Part II: three hundred (300) FH after the replacement of the rod end assy. 
Part III: 
 for rod end, after the last flight of each day or before the first flight of each day 
since the rod end has logged three hundred (300) FH or more since new or 
since overhaul. 
 for body end, after the last flight of each day or before the first flight of each day 
since the body end has logged three hundred (300 ) FH or more since new and 
until it has logged twelve hundred (1200) FH since new. 
Part IV: 
 for rod end 
 within thirthy (30) FH since receipt of this Service Bulletin and then every ten 
(10) FH for rod ends that have logged less than three hundred (300) FH since 
new or since overhaul. 
 after the last flight of each day or before the first flight of each day since the 
rod end has logged three hundred (300) FH or more since new or since 
overhaul.  
 for body end 
 within thirthy (30) FH since receipt of this Service Bulletin and then every ten 
(10) FH for body ends that have logged less than three hundred (300) FH 
since new.

### Page 5

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 5 of 57 
 after the last flight of each day or before the first flight of each day since the 
body end has logged three hundred (300) FH or more since new and until it 
has logged twelve hundred (1200) FH since new. 
Part V: within thirthy (30) FH since receipt of this Service Bulletin and then every 
twenty (20) FH until the affected damper reaches six hundred (600) FH Time 
Since New. 
Part VI: within fifty (50) FH since receipt of this Service Bulletin and then every one 
hundred (100) FH. 
Part VII: within fifty (50) FH since receipt of this Service Bulletin. 
Part VIII: within three (3) months since receipt of this Service Bulletin or before the first 
installation on the helicopter, whichever is first. 
NOTE 
For part IV and part V the compliance time must be 
sche
duled starting from the date of the last inspection 
performed according to BT 139-410, if this has been 
already accomplished at least one time. 
For part VI the compliance time must be scheduled 
starting from the date of the last inspection performed 
according to BT 139-446 part I, if this has been already 
accomplished at least one time. 
Compliance with part VII and VIII is not required for 
helicopters / parts that have already accomplished BT 
139-446 part II or part III respectively. 
C. CONCURRENT REQUIREME NTS 
N.A. 
D. REASON 
This Service Bulletin is issued in order to introduce a new one off and a new periodic 
inspection and to collect the existing periodic inspections of MR damper. 
E. DESCRIPTION 
Some failures of MR damper in the inboard spherical bearing area were experienced 
by AW139 fleet; in addition, cases of rod end loosening were reported. This Service 
Bulletin introduces the inspections to be performed on the MR damper, until 
replacement with P/N 3G6220V01353 when the body end reaches twelve hundred 
(1200) FH.

### Page 6

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 6 of 57 REVISION: C - April 10, 2018 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technica l 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin the following MMH are deemed necessary: 
Part I: six (6) MMH; 
Part II: four (4) MMH; 
Part III: half (0.5) MMH 
Part IV: half (0.5) MMH; 
Part V: half (0.5) MMH; 
Part VI: two (2) MMH; 
Part VII:five (5) MMH; 
Part VIII:half (0.5) MMH for each MR damper. 
MMH are based on hands-on time and can change with personnel and facilities 
available. 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE DESCRIPTION PART 
DM01 39- A-00-20-00-00A-120A-A Helicopter on ground for a safe 
m
aintenance 
I thru VII 
DM02 39- A-GG-02-00-00A-066A-A Platform, left (GG-01-00) I thru VII

### Page 7

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 7 of 57 
DATA MODULE DESCRIPTION PART 
DM03 39- A-62-22-02-00A-520A-A Main rotor damper – Remove 
procedures 
I, II, IV, 
V
I, VII 
DM04 39- A-62-22-02-00A-720A-A Main rotor damper – Install 
procedures 
I, II, IV, 
V
I, VII 
DM05 39- A-62-22-02-01A-921A-B Rod end (lag damper) - 
R
eplacement (remove and install 
a new item) 
IV, VI, VII 
DM06 39- A-62-22-07-00A-520A-A Anti-rotation block - Remove 
procedu
re 
VI 
DM07 39- A-62-22-07-00A-720A-A Anti-rotation block - Install 
procedu
re 
VI 
2) ACRONYMS 
AMDI Aircraft Material Data Information 
AMP Aircraft Maintenance Publication 
AMPI Aircraft Maintenance Planning information 
AR As Required 
BT Bollettino Tecnico 
DM Data Module 
FH Flight Hours 
ITEP Illustrated Tools and Equipment Publication 
LHD Leonardo Helicopter Division 
LS Local Supply 
MMH Maintenance-Man-Hours 
MMIR Maintenance Malfunction Information Report 
MR Main Rotor 
3) ANNEX 
Annex A MAG In Service Query Record n° ISQR- 16-002 
Annex B MR damper eddy current inspection 
J. PUBLICATIONS AFFECTED 
N.A. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 8

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 8 of 57 REVISION: C - April 10, 2018 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
A MR damper or a rod end assy, as applicable, can be ordered to LHD only in case 
replacement is requested by this Service Bulletin. 
NOTE 
MR damper P/N 3G6220V01353 is fully 
i
nterchangeable and mixable on the same MR Hub 
with a damper with different P/N. 
If a MR damper P/N 3G6220V01353 is furnished to 
replace a damper with different P/N, also a new 
antirotation block P/N 3G6220A05353 must be 
supplied to replace the existing one. 
The new anti-rotation block P/N 3G6220A05353 can 
be used also with damper with different P/N. 
2) CONSUMABLES  
The following consumable materials, or equivalent, are necessary to accomplish this 
Service Bulletin: 
# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 
1 Commercial Masking tape, adhesive AR LS (1) I, II 
2 Commercial Clean, lint-free, dry cloth (C011) or a bsorbent toweling AR LS (1) I, II 
3 QPL-AMS2644 Penetrant, Type II, Method C, in aerosol c ontainer AR LS (1) I, II 
4 QPL-AMS2644 Solvent remover, class 2, in aerosol c ontainer AR LS (1) I, II 
5 MS20995C41 Safety wire (C241) AR LS VII, V III 
6 
PERMACEL P422 Cod. No. 
900002514 
or 900002515 or 
900002516 or 900002517 
Tape, antifretting AR LS VII, V III 
7 MIL-PRF-85285, Ty. I C olor N° 37038 Polyurethane paint, black AR LS (1) I, II 
8 TT- N- 95 Aliphatic naphtha (C059) AR LS III 
9 Commercial Strap, tiedown 2 LS  
Refer also to AMDI for the consumable materials required to comply with the AMP DM 
referenced in the compliance instructions. 
3) LOGISTIC MATRIX 
N.A.

### Page 9

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 9 of 57 
NOTE 
(1) Required to perform the dye penetrant inspection. Refer to Annex B for 
consumable materials required for the Eddy Current inspection. 
B. SPECIAL TOOLS 
The following special tools, or equivalent, are necessary to accomplish this Service 
Bulletin: 
# P/N DESCRIPTION Q.TY NOTE PART 
10 RMGE-DS-06-2010-LH or a pproved alternative Platform left (GG-01-00) AR LS I thru VII 
11 / Magnifying glass (5 power) 1 LS (B1) I, II, III 
12 / Brush, fine tipped 1 LS (B1) I, II 
13 Commercial Luxmeter 1 LS (B1) I, II 
14 / Small, clean, dry, not contamined recipient ( beaker or equivalent) 1 LS (B1) I, II 
15 Commercial Mirror 1 LS III, V 
16 Commercial Torque wrench (capability up to 100 Nm - 8 85 lb in) 1 LS VI, VII, VIII 
17 Commercial Spanner 1-5 /16” 1 LS VII, VIII 
18 Commercial Spanner 5/8” 1 LS VI, VII, VIII 
19 Commercial Digital centesimal caliper 1 LS VI 
Refer also to ITEP for the special tools required to comply with the AMP DM 
referenced in the compliance instructions.  
SPECIAL TOOLS NOTE 
 Required to perform the dye penetrant inspection. Refer to Annex B for special (B1)
tools required for the Eddy Current inspection. 
C. INDUSTRY SUPPORT INFORMATION 
WARRANTY: Owners/Operators who comply with the instructions of this Service 
Bulletin no later than the applicable date in the “Compliance” section will be eligible to 
receive Main Rotor Damper or a Rod End Assy, as applicable, on a free of charge 
basis, except for Consumable Materials & Special Tools. 
Please Issue relevant MMIR form to your Warranty Administration Dpt.

### Page 10

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 10 of 57 REVISION: C - April 10, 2018 
3. ACCOMPLISHMENT INSTRUCTIONS 
PART I 
NOTE 
Skip steps 1 thru 3 when performing the inspection on 
t
he MR dampers kept in stock. 
1. In accordance with DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on ground for 
a safe maintenance. Disconnect the battery, all electrical power sources and/or the 
external power supply. 
2. Put the platform (GG- 01-00), or an approved alternative, adjacent to the left side of the 
fuselage. 
3. Remove the MR dampers. Refer to AMP, see DM n° 39-A-62-22-02-00A-520A-A. 
NOTE 
It is suggested to start the inspection on all the MR 
da
mpers at the same time. 
NOTE 
As an alternative to the dye penetrant inspection 
de
scribed at following step 4, it is allowed to perform 
the Eddy Current inspection, according to Annex B. 
4. With reference to figures 1 thru 6, perform the dye penetrant inspection of the MR 
damper. Operative conditions and inspection sequence shall be compliant with ASTM 
E1417, in particular the following steps shall be followed: 
4.1 Put the MR damper on a suitable work bench, as shown in figure 2. 
4.2 With reference to figure 3, on each spherical bearing, protect the liner with 
masking tape as follows: 
NOTE 
The areas to be inspected are shown in figure 1 (one 
si
de shown, the other is symmetrical), identified by the 
red boxes. 
CAUTION 
Make sure that the solvent does not come in contact 
w
ith the spherical bearing liner. 
4.2.1 Clean the surface on both sides of both ends with a clean cloth (C011) 
soa
ked with solvent. Let the solvent air dry.

### Page 11

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 11 of 57 
NOTE 
If there are slippage marks in the areas to be 
i
nspected, remove the paint, from the damper end 
surface only, using solvent. 
CAUTION 
Make sure that the adhesive masking tape adheres 
compl
etely to the damper ends surface, when 
performing following step 4.2.2. 
4.2.2 Protect the surface all around the areas to be inspected according to 
f
igures 3 thru 5, using adhesive masking tape. Make sure that the tape 
is tangent to the bearing seat, according to figures 4 and 5. 
4.3 Inspect the damper ends as follows: 
CAUTION 
Make sure that, during the inspection, the part is 
al
ways under appropriate illumination. The lighting 
system shall provide at least 1000 lx (100 fc) at the 
examination surface. Use the luxmeter to confirm this 
condition. 
4.3.1 Clean the areas to be inspected, on both sides of both ends, with a 
cl
ean cloth (C011) soaked with solvent. Let the solvent air dry. 
CAUTION 
Make sure that the recipient is clean, dry and free from 
an
y contaminant. 
4.3.2 Put a few drops of penetrant in a small recipient (beaker or equivalent) . 
CAUTION 
Make sure not to apply too much penetrant, when 
pe
rforming following step 4.3.3. 
4.3.3 Apply the penetrant with a clean, dry, fine tipped brush on all the ar eas 
to be inspected, according to figure 6 (same application to be carried 
out on the other side). Let the penetrant dwell. 
NOTE 
Dwell time must be at least one hour and no more than 
t
wo hours. 
4.3.4 Clean the penetrant in excess by first with a cl ean, dry, lint-free cloth 
(C011) or absorbent towelling.

### Page 12

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 12 of 57 REVISION: C - April 10, 2018 
4.3.5 If penetrant in excess remain, remove it with a solvent dampened lint-
free cloth (C011) or towel, until the penetrant in excess has been 
completely removed. Let the solvent air dry. 
4.3.6 Let the penetrant develop for at least thirty minutes without developer. 
4.3.7 Inspect the areas shown in figure 1 using the magnifying glass. 
4.3.7.1 If you don’t find indication of cracks, go to step 4.4. 
4.3.7.2 If you find indication of cracks, confirm the crack by wipe-off. 
4.3.7.3 If, at step 4.3.7.2, you have confirmed presence of cracks on 
the body end or on the rod end, contact Product Support 
Engineering ( CSE.AW139.AW@leonardocompany.com) for 
further instruction. 
4.4
 Remove the adhesive masking tape from all the serviceable damper ends. 
CAUTION 
Make sure that the solvent does not come in contact 
w
ith the spherical bearing liner. 
4.5 Clean all the surfaces on both sides of both ends using a cloth (C011) soaked 
w
ith solvent until all the penetrant has been removed. 
4.6 Mark a black dot, using polyurethane black paint, on the rod end and on the body 
end, in positions shown in figure 7. 
4.7 If you have removed slippage marks, cleaning the damper end surface at step 
4.2.1, restore the slippage mark using the applicable paint colour: yellow, green 
or blue. Use commercially available varnish such as thread securing/sealing 
product or equivalent alternatives. Let dry for one hour at 25°C, or as otherwise 
specified by product specification. 
5. Install the MR damper/dampers. Refer to AMP, see DM n° 39-A-62-22-02-00A-720A-A. 
6. Remove the platform (GG- 01-00) from the left side of the fuselage. 
7. Return the helicopter to flight configuration. 
8. Record for compliance with part I of this Service Bulletin on the MR damper logcard. 
9. Send the attached compliance form to the following mail box: 
cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
an
d compile the “Service Bulletin Application Communication”.

### Page 13

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 13 of 57 
PART II 
1. In accordance with DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on ground for 
a safe maintenance. Disconnect the battery, all electrical power sources and/or the 
external power supply. 
2. Put the platform (GG- 01-00), or an approved alternative, adjacent to the left side of the 
fuselage. 
3. Remove the affected MR damper. Refer to AMP, see DM n° 39-A-62-22-02-00A-520A-
A. 
NOTE 
As an alternative to the dye penetrant inspection 
de
scribed at following step 4, it is allowed to perform 
the Eddy Current inspection, according to Annex B. 
4. With reference to figures 1 thru 6, perform the dye penetrant inspection of the affected 
MR damper rod end. Operative conditions and inspection sequence shall be compliant 
with ASTM E1417, in particular the following steps shall be followed: 
4.1 Put the MR damper on a suitable work bench, as shown in figure 2. 
4.2 With reference to figure 3 view B, on the rod end spherical bearing, protect the 
liner with masking tape as follows: 
NOTE 
The area to be inspected is shown in figure 1 view B 
(
one side shown, the other is symmetrical), identified 
by the red boxes. 
CAUTION 
Make sure that the solvent does not come in contact 
w
ith the spherical bearing liner. 
4.2.1 Clean the surface on both sides of the rod end with a clean cloth 
(
C011) soaked with solvent. Let the solvent air dry. 
NOTE 
If there are slippage marks in the areas to be 
i
nspected, remove the paint, from the damper end 
surface only, using solvent. 
CAUTION 
Make sure that the adhesive masking tape adheres 
compl
etely to the damper end surface, when 
performing following step 4.2.2.

### Page 14

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 14 of 57 REVISION: C - April 10, 2018 
4.2.2 Protect the surface all around the areas to be inspected according to 
figures 3 thru 5, using adhesive masking tape. Make sure that the tape 
is tangent to the bearing seat, according to figures 4 and 5. 
4.3 Inspect the damper rod end as follows: 
CAUTION 
Make sure that, during the inspection, the part is 
al
ways under appropriate illumination. The lighting 
system shall provide at least 1000 lx (100 fc) at the 
examination surface. Use the luxmeter to confirm this 
condition. 
4.3.1 Clean the areas to be inspected, on both sides of the rod end, with a 
cl
ean cloth (C011) soaked with solvent. Let the solvent air dry. 
CAUTION 
Make sure that the recipient is clean, dry and free from 
an
y contaminant. 
4.3.2 Put a few drops of penetrant in a small recipient (beaker or equivalent) . 
CAUTION 
Make sure not to apply too much penetrant, when 
pe
rforming following step 4.3.3. 
4.3.3 Apply the penetrant with a clean, dry, fine tipped brush on all the areas 
t
o be inspected, according to figure 6 view B (same application to be 
carried out on the other side). Let the penetrant dwell. 
NOTE 
Dwell time must be at least one hour and no more than 
t
wo hours. 
4.3.4 Clean the penetrant in excess by first with a clean, dry, lint-free cl oth 
(C011) or absorbent towelling. 
4.3.5 If penetrant in excess remain, remove it with a solvent dampened lint-
free cloth (C011) or towel, until the penetrant in excess has been 
completely removed. Let the solvent air dry. 
4.3.6 Let the penetrant develop for at least thirty minutes without developer. 
4.3.7 Inspect the areas shown in figure 1 using the magnifying glass. 
4.3.7.1 If you don’t find indication of cracks, go to step 4.4. 
4.3.7.2 If you find indication of cracks, confirm the crack by wipe-off.

### Page 15

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 15 of 57 
4.3.7.3 If, at step 4.3.7.2, you have confirmed presence of cracks on 
the rod end, contact Product Support Engineering 
(CSE.AW139.AW@leonardocompany.com) for further 
instruction.  
4.4 Remove the adhesive masking tape from the serviceable rod end. 
CAUTION 
Make sure that the solvent does not come in contact 
w
ith the spherical bearing liner. 
4.5 Clean all the surfaces on both sides of the rod end using a cloth (C011) soake d 
with solvent until all the penetrant has been removed. 
4.6 Mark a black dot, using polyurethane black paint, on the rod end, in position 
shown in figure 7. 
4.7 If you have removed slippage marks, cleaning the damper end surface at step 
4.2.1, restore the slippage mark using the applicable paint colour: yellow, green 
or blue. Use commercially available varnish such as thread securing/sealing 
product or equivalent alternatives. Let dry for one hour at 25°C, or as otherwise 
specified by product specification. 
5. Install the MR damper . Refer to AMP, see DM n° 39-A-62-22-02-00A-720A-A. 
6. Remove the platform (GG- 01-00) from the left side of the fuselage. 
7. Return the helicopter to flight configuration. 
8. Record for compliance with part II of this Service Bulletin on the MR damper logcard. 
9. Send the attached compliance form to the following mail box: 
cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
an
d compile the “Service Bulletin Application Communication”.

### Page 16

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 16 of 57 REVISION: C - April 10, 2018 
PART III 
1. In accordance with DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on ground for 
a safe maintenance. Disconnect the battery, all electrical power sources and/or the 
external power supply. 
2. Put the platform (GG- 01-00), or an approved alternative, adjacent to the left side of the 
fuselage. 
NOTE 
Refer to the “Compliance” section to define the 
ap
plicability of the following steps 3 thru 5. 
3. With reference to figure 8, turn the MR head to move the applicable MR damper above 
the platform and get access to the work area. 
NOTE 
As an alternative to the detailed inspection described 
at 
following step 4, it is allowed to perform the Eddy 
Current inspection, according to Annex B, on the areas 
shown in figure 19. 
4. With reference to figures 8 and 19, perform a detailed inspection on the MR damper, 
using the magnifying glass and mirror: 
NOTE 
The areas to be inspected on the MR damper are 
sho
wn in figure 19 (top side shown, bottom side is 
symmetrical). 
CAUTION 
Make sure that the aliphatic naphtha (C059) does not 
come 
in contact with the spherical bearing liner. 
4.1 Clean the surface to be inspected, on both sides of both ends, with a clean cloth  
(C011) soaked with aliphatic naphtha (C059). 
4.2 Do a detailed inspection of the damper rod end (3) for cracks. If you find cracks, 
contact Product Support Engineering (CSE.AW139.AW@leonardocompany.com) 
for further instruction. 
4.3
 Do a detailed inspection of the damper body end (2) for cracks. If you find cracks, 
contact Product Support Engineering (CSE.AW139.AW@leonardocompany.com) 
for further instruction. 
5. 
Repeat steps 3 and 4 until you have checked all the applicable MR dampers. 
6. Remove the platform (GG- 01-00) from the left side of the fuselage.

### Page 17

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 17 of 57 
7. Return the helicopter to flight configuration and record for compliance with part III of this 
Service Bulletin.

### Page 18

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 18 of 57 REVISION: C - April 10, 2018 
PART IV 
1. In accordance with DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on ground for 
a safe maintenance. Disconnect the battery, all electrical power sources and/or the 
external power supply. 
NOTE 
Refer to the “Compliance” section to define the 
ap
plicability of the following steps 2 thru 4. 
2. With reference to figure 8, get access to the work area. 
NOTE 
Damper (1) and/or rod end (3) removal is not 
ne
cessary to perform the inspection. 
3. With reference to figures 8 and 9 perform the inspection as follows: 
3.1 Examine the bearing of the rod end (3) for rotation in the damper seat by looking 
for slippage marks misalignment. If you find rotation (as shown in figure 9), 
replace the rod end. Refer to AMP, see DM n° 39-A-62-22-02-01A-921A-B. 
3.2 Examine the bearing of the body end (2) for rotation in the damper seat by looking 
for slippage marks misalignment. If you find rotation (as shown in figure 9), 
replace the damper (1). Refer to AMP, see DM n° 39-A-62-22-02-00A-520A-A 
and 39-A-62-22-02-00A-720A-A. 
4. Repeat step 3 to inspect the other MR dampers. 
5. Return the helicopter to flight configuration and record for compliance with Part IV of this 
Service Bulletin on the helicopter logbook. 
6. Send the attached compliance form to the following mail box: 
cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
an
d compile the “Service Bulletin Application Communication”.

### Page 19

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 19 of 57 
PART V 
1. In accordance with DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on ground for 
a safe maintenance. Disconnect the battery, all electrical power sources and/or the 
external power supply. 
2. With reference to figure 10, get access to the work area. 
3. With reference to figure 11, do a visual inspection of the lag damper broached ring nut 
(6). 
NOTE 
Damper (1) and rod end (3) removal is not necessary 
t
o perform the inspection. The parts are shown 
removed/disassembled for better clarity purposes only. 
3.1 With reference to figures 11 and 12, using a mirror, check the four  teeth of the 
broached ring (5) and relative four damper piston slots (4) for damage, correct 
engagement and alignment. 
3.2 In case of findings (a sample of possible damage is shown in figure 13) contact 
Product Support Engineering ( CSE.AW139.AW@leonardocompany.com) for 
further instruction. 
4. 
Repeat step 3 to inspect the other MR dampers. 
5. Return the helicopter to flight configuration and record for compliance with Part V of this 
Service Bulletin on the helicopter logbook. 
6. Send the attached compliance form to the following mail box: 
cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
an
d compile the “Service Bulletin Application Communication”.

### Page 20

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 20 of 57 REVISION: C - April 10, 2018 
PART VI 
1. In accordance with DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on ground for 
a safe maintenance. Disconnect the battery, all electrical power sources and/or the 
external power supply. 
2. Put the platform (GG- 01-00), or an approved alternative, adjacent to the left side of the 
fuselage. 
3. With reference to figure 16, turn the MR head to move the applicable MR damper above 
the platform and get access to the work area. 
4. With reference to figures 16 thru 18, perform the following checks on the first MR 
damper: 
NOTE 
Before starting the friction check, lightly rotate the body 
en
d around the damper axis to put it near the middle 
position (0°). 
4.1 Perform a bearing friction torque check of the damper body end according to 
figure 18 view G. If the value is higher than 30.0 Nm (265.5 lb in), proceed with 
step 4.1.1, otherwise go to step 4.2. 
4.1.1 Replace the MR damper (see AMP DM n° 39-A-62-22-02-00A-520A-A 
and DM n° 39-A-62-22-02-00A-720A-A). 
4.1.2 Go to step 4.3. 
4.2 Perform a bearing friction torque check of the damper rod end according to figure 
18 view H. If the value is higher than 30.0 Nm (265.5 lb in), replace the damper 
rod end (see AMP DM n° 39-A-62-22-02-01A-921A-B), otherwise proceed with 
step 4.3. 
4.3 With reference to figures 16 and 17 do a detailed inspection for wear of the 
damper anti-rotation block as follows: 
4.3.1 Mark a reference line on the MR hub lower arm at a distance of 55 mm 
(2.16 in) from the body end blocking ring, according to figure 17 view 
E. Use a digital centesimal caliper to measure the distance and an 
erasable ink pen to mark the reference line. 
4.3.2 With reference to figure 16 section D-D, move the body end to the fully 
up position using a torque wrench, in order to measure dimension “A”. 
4.3.3 Measure dimension “A” from the lower surface of the MR hub arm to 
the lower surface of the body end, alongside the reference line 
previously marked, using a digital centesimal caliper, as shown in 
figure 17 view F.

### Page 21

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 21 of 57 
4.3.4 Make sure that the measured dimension “A” is lower than 26.90 mm 
(1.06 in). 
4.3.5 With reference to figure 16 section D-D, move the body end to the fully 
down position using a torque wrench, in order to measure dimension 
“B”. 
4.3.6 Measure dimension “B” from the lower surface of the MR hub arm to 
the lower surface of the body end, alongside the reference line 
previously marked, using a digital centesimal caliper, as shown i n 
figure 17 view F. 
4.3.7 Make sure that the measured dimension “B” is higher than 24.35 mm 
(0.96 in). 
4.3.8 If the dimension measured are not within the given limits, replace the 
anti-rotation block with a new one. Refer to AMP, see DM n° 39-A- 62-
22-07-00A-520A-A and DM n° 39-A-62-22-07-00A-720A-A. 
5. Repeat steps 3 and 4 until you have checked all the MR dampers. 
6. Remove the platform (GG- 01-00) from the left side of the fuselage. 
7. Return the helicopter to flight configuration and record for compliance with part VI of this 
Service Bulletin on the helicopter logbook. 
8. Send the attached compliance form to the following mail box: 
cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
an
d compile the “Service Bulletin Application Communication”.

### Page 22

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 22 of 57 REVISION: C - April 10, 2018 
PART VII 
1. In accordance with DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on ground for 
a safe maintenance. Disconnect the battery, all electrical power sources and/or the 
external power supply. 
2. Put the platform (GG- 01-00), or an approved alternative, adjacent to the left side of the 
fuselage. 
3. Get access to the cockpit. Set the rotor brake lever to OFF. 
4. With reference to figure 14, turn the MR head to move the applicable MR damper above 
the platform and get access to the work area. 
NOTE 
Do not remove the damper rod end (2) from the pitch 
con
trol lever during this procedure. The damper (1) is 
shown removed in some figures for better clarity 
purposes only. 
5. Wit h reference to figure 14 section C-C, do a visual inspection of the damper rod end 
installation. 
5.1 Make sure that the special washer P/N 3G6220A05052 is installed. 
5.2 If the special washer P/N 3G6220A05052 is present, go to step 6. 
5.3 If the special washer P/N 3G6220A05052 is not present, do as follows: 
5.3.1 Remove the MR damper. Refer to AMP, see DM n° 39-A-62-22-02-
00A-520A-A. 
5.3.2 Perform disassembly, inspections and assembly of the damper as 
prescribed by the compliance instructions (paragraph 8) in Annex A. 
CAUTION 
Install special washer P/N 3G6220A05052 according to 
B
T 139-402 when you install the lag damper at 
following step 5.3.3. 
5.3.3 Install the MR damper. Refer to AMP, see DM n° 39- A-62-22-02-00A-
720A-A. 
5.3.4 Go to step 7. 
6. With reference to figure 14 view A and to figure 15, check the torque of the damper 
broached ring nut (3) on the first MR damper.

### Page 23

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 23 of 57 
WARNING 
MAKE SURE THAT THE ROTOR BRAKE ENGAGES 
W
HEN YOU PERFORM THE TORQUE CHECK. AN 
INJURY TO PERSONS OR DAMAGE TO THE 
EQUIPMENT CAN OCCUR IF THE MAIN ROTOR 
HEAD TURNS. 
6.1 Set the rotor brake lever to ON. 
6.2
 Get access to the damper rod end (2). 
NOTE 
Identify and record the wiring scheme before removing 
t
he safety wire. 
6.3 Cut and remove the safety wire from the damper. Discard the safety wire. 
6.4
 With reference to figures 14 and 15, move the ring nut (3) away from the 
broaching of the rod end (2) toward the damper body (1). Use a plastic mallet 
and a soft plunger to disengage it from the broaching of the rod end (2). When 
you do this operation, make sure not to disengage the ring nut (3) from the lock 
ring (5). 
6.5 Protect the rod end (2) with a film of antifretting tape PERMACEL P422 or 
equivalent. 
CAUTION 
To torque the ring nut at following step 6.6, make sure 
t
o rotate the ring nut clockwise (looking outboard from 
the MR hub), according to figure 15. 
6.6 Set the torque wrench to 53 Nm (469 lb in), lock the rod end with a spanner,  and 
try to torque the ring nut (3). 
6.6.1 Verify that the ring nut (3) does not rotate with respect to the rod end 
(2). 
6.6.2 If rotation is not found go to step 6.7, otherwise proceed with following 
step 6.6.3. 
6.6.3 Remove the MR damper. Refer to AMP, see DM n° 39-A-62-22-02-
00A-520A-A. 
6.6.4 Perform disassembly, inspections and assembly of the MR damper as 
prescribed by steps 8 thru 23 of the compliance instructions (paragraph 
8) in annex A. 
6.6.5 Install the MR damper. Refer to AMP, see DM n° 39-A-62-22-02-00A-
720A-A.

### Page 24

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 24 of 57 REVISION: C - April 10, 2018 
6.6.6 Go to step 7. 
6.7 Torque the ring nut (3) to 63 Nm (558 lb in). 
6.8 After torque application, move the ring nut (3) backwards to the damper (1) and 
do as follows: 
6.8.1 Make sure that the broached teeth (4) of the rod end are perfectly 
aligned to the lock ring (5). 
6.8.2 If they are aligned, go to step 6.11, otherwise proceed with step 6.9. 
CAUTION 
Do not release the torque to align the teeth. Unscrew 
actio
n will introduce potential loosening of rod end 
during in flight operation. 
6.9 If the teeth are misaligned, increase the torque value to reach the correct 
al
ignment, up to a maximum of 80 Nm (708 lb in). Do not exceed 80 Nm (708 lb 
in). 
6.10 If it is not possible to align the teeth within this range, do as follows: 
6.10.1 Remove the MR damper. Refer to AMP, see DM n° 39-A-62-22-02-
00A-520A-A. 
6.10.2 Remove the rod end (2) from the MR damper according to the 
applicable steps of AMP DM n° 39-A-62-22-02-01A-921A-B. 
6.10.3 Perform steps 19 thru 23 of the compliance instructions (paragraph 8) 
in Annex A. 
6.10.4 Install the MR damper. Refer to AMP, see DM n° 39-A-62-22-02-00A-
720A-A. 
6.10.5 Go to step 7. 
6.11 Remove the protective tape from the rod end (2). 
6.12 Make sure that there are not scratches or dents on the rod end (2). 
6.13 Move the ring nut (3) in its position on the broaching of the rod end (2). Do this 
until top and bottom holes on the ring nut (3) come in view for the installation of 
the wire. 
6.14 Safety the damper with new safety wire (C241), according to the scheme 
recorded at step 6.3. 
6.15 Record for compliance with part VII of this Service Bulletin on the component 
logcard. 
7. Repeat steps 3 thru 6 until you have checked all the MR dampers. 
8. Remove the platform (GG- 01-00) from the left side of the fuselage. 
9. Return the helicopter to flight configuration. 
10. Record for compliance with part VII of this Service Bulletin on the helicopter logbook.

### Page 25

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 25 of 57 
11. Send the attached compliance form to the following mail box: 
cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
an
d compile the “Service Bulletin Application Communication”.

### Page 26

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 26 of 57 REVISION: C - April 10, 2018 
PART VIII 
1. Perform the torque check on the MR damper according to the compliance instructions 
(paragraph 8) in Annex A. 
NOTE 
If the damper is in new condition (zero FH since new), 
when performing the torque check according to Annex 
A, do not apply steps 8.7 thru 8.16. 
2. Send the attached compliance form to the following mail box: 
 cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
an
d compile the “Service Bulletin Application Communication”.

### Page 27

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 27 of 57 
 
 
  
Areas to be inspected (two on body end and two on rod end) shown in red boxes 
(on
e side shown, the other is symmetrical) 
Figure 1 
 
Damper must be removed from the helicopter and positioned on a suitable work bench 
Figure 2 
  
VIEW A 
BODY END 
VIEW B 
ROD END

### Page 28

S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 28 of 57 REVISION: C - April 10, 2018 
Body end and rod end must be protected with masking tape as shown (on both sides) 
Figure 3 
 
On the rod end apply the masking tape as shown. Red line (shown on the picture for 
reference only) is tangent to the spherical bearing seat (yellow line, shown on the 
picture for reference only). 
Figure 4 
VIEW B 
ROD END 
VIEW A 
BODY END

### Page 29

S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 29 of 57 
 
On the body end apply the masking tape as shown. Red line (shown on the picture for 
reference only) is tangent to the spherical bearing seat (yellow line, shown on the 
picture for reference only). 
Figure 5 
 
 
Apply dye penetrant on both sides of both ends in the areas shown.  
Figure 6 
 
VIEW A 
BODY END 
VIEW B 
ROD END

### Page 30 (OCR)

K LEONARDO
HELICOPTERS
NDT INSPECTION MARKING ON DAMPER ROD END
MARK A DOT HERE
USING BLACK PAINT
NDT INSPECTION MARKING ON DAMPER BODY END
Figure 7
S.B. N°139-450 ALERT
DATE: April 20, 2016
Page 30 of 57  REVISION: C - April 10, 2018

### Page 31

Figure 
8 
S.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 31 of 57

### Page 32

Figure 
9 
 S.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 32 of 57 REVISION: C - April 10, 2018 
 
 
 
 
 
 
Sample of bearing rotation (slippage marks misalignment)

### Page 33

Figure 10 
S
.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 33 of 57

### Page 34 (OCR)

* LEONARDO  HELICOPTERS
Figure 11
S.B. N°139-450 ALERT
DATE: April 20, 2016
Page 34 of 57  REVISION: C - April 10, 2018

### Page 35

Figure 12 
S
.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 35 of 57 
 
 
 
Area to be inspected for damage, correct engagement and alignment 
  
View A 
A 
BROACHED 
R
ING TOOTH 
PISTON SLOT

### Page 36

Figure 13 
 S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 36 of 57 REVISION: C - April 10, 2018 
 
 
Sample of damage on piston slot

### Page 37

Figure 14 
S
.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 37 of 57

### Page 38 (OCR)

K LEONARDO
HELICOPTERS
MOVE THE RING NUT (3) AWAY FROM
THE BROACHING OF THE ROD END (2)  2
IF THE BROACHED TEETH (4) ARE
NOT CORRECTLY ALIGNED
TO THE LOCK RING (5)
INCREASE THE TORQUE VALUE UP TO
A MAXIMUM OF 80 Nm (708 Ib in)
Page 38 of 57
RING NUT BACKING
CORRECT POSITION
HOLD THE ROD END WITH A SPANNER
TORQUE THE RING NUT TO 63 Nm (558 Ib in)
AS SHOWN (RED ARROW) IN THE PICTURE
(TWO OPERATORS REQUIRED)
MAKE SURE THAT THE BROACHED TEETH (4)
OF THE ROD END (2) ARE PERFECTLY ALIGNED
TO THE LOCK RING (5)
IT IS NECESSARY TO MOVE THE RING NUT (3)
BACKWARDS TO THE DAMPER TO DO THIS
Figure 15
S.B. N°139-450 ALERT
DATE: April 20, 2016
REVISION: C - April 10, 2018

### Page 39 (OCR)

* LEONARDO
HELICOPTERS
E
VIEW
(TYPICAL 5 POSITIONS
BODY END
FULLY UP POSITION
ANTI-ROTATION BLOCK
DIMENSION A
DIMENSION B
FULLY DOWN POSITION
SECTION D-D
Figure 16
S.B. N°139-450 ALERT
DATE: April 20, 2016
REVISION: C - April 10, 2018  Page 39 of 57

### Page 40 (OCR)

• LEONARDO
HELICOPTERS
MARK A REFERENCE LINE
55.0 mm FROM THE
BODY END BLOCKING RING
USE A DIGITAL
CENTESIMAL CALIPER
40
MEASURE DIMENSION
VIEW E  "A" AND "B" IN THE RED AREA
DIMENSION TO BE MEASURED
FROM LOWER SIDE OF MR HUB
TO LOWER SURFACE OF BODY END  VIEW FROM BOTTOM SIDE OF BODY
ALONGSIDE THE REFERENCE  END SHOWING CALLIPER CONTACT AREA
LINE PREVIOUSLY MARKED
MOVE UP TO MEASURE
DIMENSION "A"
IN FULLY UP POSITION
MOVE DOWN TO MEASURE
DIMENSION "B" IN FULLY
DOWN POSITION
VIEW F
Figure 17
S.B. N°139-450 ALERT
DATE: April 20, 2016
Page 40 of 57  REVISION: C - April 10, 2018

### Page 41 (OCR)

* LEONARDO  HELICOPTERS
VIEW H
FILLING
Figure 18
S.B. N°139-450 ALERT
DATE: April 20, 2016
REVISION: C - April 10, 2018  Page 41 of 57

### Page 42 (OCR)

* LEONARDO  HELICOPTERS
AREAS TO BE INSPECTED
(ROD END)
UPPER SIDE SHOWN
LOWER SIDE SYMMETRICAL
AREA TO BE INSPECTED
(BODY END)
UPPER SIDE SHOWN
LOWER SIDE SYMMETRICAL
Figure 19
S.B. N°139-450 ALERT
DATE: April 20, 2016
Page 42 of 57  REVISION: C - April 10, 2018

### Page 43

ANNEX A 
S
.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 43 of 57 
ANNEX A 
MAG IN SERVICE QUERY RECORD N° ISQR-16-002

### Page 44 (OCR)

• LEONARDO
ANNEX A  HELICOPTERS
IN SERVICE QUERY
MECAER I AVIATION I GROUP  RECORD
Report Data
ISQR n.  ISQR-16-002  ISQR Opening Date  2016-01-25
Affected Item Data  Item Usage Data  Equipment Type
Item Name  Main Rotor Lag Damper  Item TSN (total FH)  N/A  Damper  LGCP
Item P/N (MAG)  M006-01H001-007/-009  Item total cycles/Indg  N/A  MLG S/A  Brakes
Item P/N (Cust.)  3G6220V01351/1352  Item TSO (FH)  N/A  NLG S/A  HBS
Item S/N  See below  R/A  •  Steering  •
Uplock  Wheels
Installation Data  A/C Data  LGCV  FCS/FCR
NHA P/N  N/A  A/C Type  AW 139  WBPEM  HSA
NHA Name  AW139 helicopter  A/C S/N  N/A  Ctrl lever  Other (specify) D
NHA S/N  N/A  A/C TSN (total FH)  N/A  Skids
Applicant
Customer  AgustaWestland
Department  Customer Support & Service
Name / Title  Alessandro Crespi
Query data
Email from A. Crespi to M.
Query ref. info  Attachments
Cantarella and others 2016-01-25  MR Damper AW139 e
AW189 - BT Verifica c
Query details  CLASSIFICATION: Level 4
See attached email.
Response
Email to A. Crespi 2016-01-27 and
Response ref. info  2016-02-01. Email to R. Vanni  Attachments
2016-02-11
Response details
1. Introduction
The present document provides information requested by AW about the tasks to be performed on the Main Rotor Lag
Dampers P/N M006-01H001-007/-009 to make sure that the installation torque applied to the Eye End Assembly is
within the reduced range of 60-80 Nm.
2. Applicability
The present instructions apply to  All MR dampers P/N 3G6220V01351 (MAG P/N M006-01H001-007) and P/N 3G6220V01352 (MAG P/N M006-
01H001-009) up to S/N MCR8764 included, except MR dampers listed in Table 1.
• All MR Dampers P/N 3G6220V01351 (MAG P/N M006-01H001-007) and P/N 3G6220V01352 (MAG P/N M006-
01H001-009) that have removed the damper eye end, in accordance to applicable AW139 Aircraft Maintenance
Procedure, before the issue of Finmeccanica Helicopter Division Bollettino Tecnico 139-446 (endorsing present
instructions).
NOTE: The MRLD exact S/N may be composed of either four or five digits, possibly preceded by letters MCR and/or
followed by letters A and/or B.  For the purpose of the present instructions, only valid numerical characters are
considered, neglecting "MCR", "A", "B" and initial zeros.
Possible examples follow:
S/N 0272 will be referred to as S/N 272;
S/N 00344AB will be referred to as S/N 344;
S/N MCR1848A will be referred to as S/N 1848;
S/N MCR07568 will be referred to as S/N 7568;
S/N MCR10755 will be referred to as S/N 10755;
MAG confirms that no duplicates exist in the valid numerical digits of item serialization (that is, only one among S/N
715, S/N MCR0715, S/N MCRO0715 or S/N MCR0715AB exists).
Mecaer Aviation Group S.p.A. Proprietary Information
ALL INFORMATION CONTAINED IN OR DISCLOSED BY THIS DOCUMENT IS CONSIDERED CONFIDENTIAL AND PROPRIETARY BY MECAER AVIATION GROUP S.P.A..
ALL DESIGN, MANUFACTURE, USE, REPRODUCTION AND SALES RIGHTS ARE RESERVED BY MAG S.P.A.
MOD-PS-1-001 Rev.0
S.B. N°139-450 ALERT
DATE: April 20, 2016
Page 44 of 57  REVISION: C - April 10, 2018

### Page 45 (OCR)

ANNEX A  * LEONARDO  HELICOPTERS
IN SERVICE QUERY
MECAERIAVIATION| GROUP  RECORD
3. References
M006-01H001 MAG Drawing, AW139 Main Rotor Lag Damper, rev. AB
M006-283  MAG Engineering Change Order, AW139 Main Rotor Lag Damper, 9/10/2015
62-21-06  00/00 (AGUSTAN 36220001151/6220001392) and AVAIN KOTOR HEAD-  007/009 (AGUSTA P/N 3G6220V01351/3G6220V01352) and AW 149/189
DAMPER P/N M134-01H001-001 (AGUSTA P/N 4F6220V00251), Issue 4 Rev. 3
4. Place of embodiment
Mecaer, AgustaWestland, Helicopter Operator Maintenance
5. Compliance
At the first return to MAG of affected Dampers. According to AgustaWestland dispositions for Dampers installed on
helicopters. Before installation for items held in stock as spare.
6. Required Manpower
One half (0,5) maintenance man-hour (MMH) with Damper removed from H/C, potential NDT excluded.
7. Materials Information
a. Required Material
P/N  Description  Qty  Note
MS20995C41  Safety Wire  AR
M006-01H020-103  Broached Ring  AR
PD-680  Cleaning solvent  AR  equivalent alternatives may be used
Commercial  Scotch Brite  AR
Commercial  Solvent Class 2  AR  See step 10c. and related note
Commercial  Penetrant Type 1  AR  See step 10c. and related note
Commercial  Developer Form D  AR  See step 10c. and related note
b. Required Tools
P/N  Description  Qty  Note
Commercial  Torque Wrench  50-80 Nm range
Commercial  Wrench  33.3mm min. (1.31in.)
Commercial  Hammer
Commercial  Aluminum or Teflon pin
M006-01T029  Locking Tool  Alternative method: vise equipped with protective
teflon or rubber false jaws
M00601H001001A23L  Wrench tool
8.  Compliance Instructions
With Damper on ground, proceed as follows. Refer to CMM IPL numeration, as per Figure 1;
Manually verify that the Eye End assy (1-60) does not rotate with respect to the Piston. Record the result of this
verification;
3.  Cut and remove the two "U shape" wire-locking from broached ring nut (1-40), see Figure 2;
4. Install damper on tool P/N M006-01T029 or lock Body End side on a vise equipped with protective teflon or
rubber false jaws;
5.  Using a hammer and an aluminum or Teflon pin, gently move broached ring nut (1-40) away from the eye end
(towards the damper body side) as necessary to disengage the eye end assy (1-60) from the broached ring (1-
50). Take care that the broached ring nut (1-40) is still engaged with the broached ring (1-50);
NOTE
Piston shall be adequately extended so to provide
sufficient clearance to allow broached ring nut to be
moved back.
6. If locked on a vise, remove damper from the vise and lock broached ring nut (1-40) on the vise. Otherwise, lock
broached ring nut (1-40) with a wrench;
7. Set torque wrench to 50 Nm and, by using wrench tool P/N M00601H001001A23L, try to torque eye end (1-60).
Verify that the Eye End assy (1-60) does not rotate with respect to the Piston. If Eye End assy (1-60) rotates
with respect to the Piston, proceed to step 8. If no rotation is detected, proceed to step 17. Record the result of
this verification;
Mecaer Aviation Group S.p.A. Proprietary Information
ALL INFORMATION CONTAINED IN OR DISCLOSED BY THIS DOCUMENT IS CONSIDERED CONFIDENTIAL AND PROPRIETARY BY MECAER AVIATION GROUP S.P.A..
ALL DESIGN, MANUFACTURE, USE, REPRODUCTION AND SALES RIGHTS ARE RESERVED BY MAG S.P.A.
MOD-PS-1-001 Rev.0
S.B. N°139-450 ALERT
DATE: April 20, 2016
REVISION: C - April 10, 2018  Page 45 of 57

### Page 46 (OCR)

LEONARDO
ANNEX A  HELICOPTERS
IN SERVICE QUERY
MECAERIAVIATIONI GROUP  RECORD
Unscrew eye end assy (1-60), remove broached ring (1-50) and broached ring nut (1-40);
Clean eye end assy (1-60), broached ring (1-50) and broached ring nut (1-40) and the internal threaded section
of the damper piston with cleaning solvent PD-680 or equivalent and dry thoroughly with dry, filtered
compressed air;
10. With reference to Figure 3:
Inspect broached ring (1-50) for evidence of wear and damages, with particular attention to the four pins
engaging the piston grooves. Refer to Figure 4 for an example of acceptable broached ring. In presence of
wear or damages replace it with a new one.
Visually inspect damper piston, in the locking grooves area, for wear, damages and cracks. Refer to Figure
4 for an example of acceptable piston. In presence of damages replace the damper.
In case of rotation detected during verifications performed at steps 2 or 7, perform a fluorescent penetrant
NDT inspection of piston extremity area, in accordance with ASTM E1417 using a solvent Class 2, a
penetrant Type 1, Method C, Level 2 or 3 with a developer in Form D - no cracks are allowed.
All the products listed in the SAE AMS2644 QPL
(Qualified Products List) and qualified as Type 1, Level
2, Methods A B or D, may also be used for this
inspection only  if applied in accordance with the
used for method C (penetrant excess
removal with solvent).
CAUTION
COMPLETION  PENETRANT  INSPECTION
CAREFULLY CLEAN THE PART IN ORDER TO REMOVE
ANY RESIDUE OF FLUORESCENT PRODUCT.
11. Install broached ring nut (1-40) on the damper piston rod; orienting the arrow, if marked, to the eye end. If
arrow is not marked, broached ring nut (1-40) may be installed both ways;
Install broached ring (1-50) on the piston;
Install by hand the eye end assy (1-60) on the piston. It must be possible to smoothly screw the eye end. If it is
possible to screw the eye end assy (1-60) until abutment and last thread fillet engagement by hand, proceed to
step 15. Otherwise, proceed to step 14;
Unscrew the eye end assy (1-60) and brush the threaded part with Scotch Brite and return to step 13;
Make sure broached ring is axially aligned with the piston. Engage broached ring nut (1-40) on the broached
ring (1-50). Take care not to engage the eye end assy (1-60);
Install damper on tool M006-01T029 or lock broached ring nut on a vise or with a wrench;
By using wrench tool P/N M00601H001001A23L, torque eye end (1-60) to 60 Nm (531 Ib.in).If broached ring
(1-50) and eye end (1-60) broachings are not correctly aligned, increase the load up to achieve the correct
alignment, without exceeding 80 Nm (708 Ib.in). In case broaching cannot be aligned within this range proceed
to step 18. Otherwise, proceed to step 21;
CAUTION
NEVER TRY TO ALIGN COMPONENT BROACHINGS BY
UNSCREWING  EYE  END,  IT  CAN  CAUSE AN
UNCONTROLLED TORQUE LOSS.
Loosen and remove Eye End (1-60);
Disengage broached ring nut (1-40) from broached ring (1-50);
20. Remove broached ring (1-50) and rotate it by 90°. If broached ring (1-50) has been already mated to piston in
all four possible positions, replace broached ring (1-50) with a new one. Proceed to step 13;
Move the broached ring nut (1-40) towards the eye end assy and verify its correct positioning;
Using wire MS20995C41, safety wire the broached ring nut (1-40) and the eye end assy (1-60) in two positions
(refer to Figure 2);
Limited axial movement of broached ring nut (1-40)
after lockwiring is acceptable.
23. Record AW Service Bulletin embodiment by marking the number of Finmeccanica Helicopter Division Bollettino
Tecnico endorsing present instructions (BT 139-446, Part III) on item Log Card
Mecaer Aviation Group S.p.A. Proprietary Information
ALL INFORMATION CONTAINED IN OR DISCLOSED BY THIS DOCUMENT IS CONSIDERED CONFIDENTIAL AND PROPRIETARY BY MECAER AVIATION GROUP S.P.A.
ALL DESIGN, MANUFACTURE, USE, REPRODUCTION AND SALES RIGHTS ARE RESERVED BY MAG S.P.A.
MOD-PS-1-001 Rev.0
S.B. N°139-450 ALERT
DATE: April 20, 2016
Page 46 of 57  REVISION: C - April 10, 2018

### Page 47 (OCR)

ANNEX A  * LEONARDO  HELICOPTERS
IN SERVICE QUERY
MECAERIAVIATION| GROUP  RECORD
40
50
60
Figure 1 - IPL Items identification
Figure 2 - Eye End lockwiring - 2 positions, "U" shape - Internal path
Mecaer Aviation Group S.p.A. Proprietary Information
ALL INFORMATION CONTAINED IN OR DISCLOSED BY THIS DOCUMENT IS CONSIDERED CONFIDENTIAL AND PROPRIETARY BY MECAER AVIATION GROUP S.P.A..
ALL DESIGN, MANUFACTURE, USE, REPRODUCTION AND SALES RIGHTS ARE RESERVED BY MAG S.P.A.
MOD-PS-1-001 Rev.0
S.B. N°139-450 ALERT
DATE: April 20, 2016
REVISION: C - April 10, 2018  Page 47 of 57

### Page 48 (OCR)

ANNEX A  * LEONARDO  HELICOPTERS
IN SERVICE QUERY
MECAERIAVIATIONI GROUP  RECORD
PISTON CRACKS
AFFECTED AREA
(starting from grooves)
BROACHED RING
WEAR AREA (PINS)
Figure 3 - Inspection details
BROACHED RING  PISTON
PIN
GROOVE•
Figure 4 - Examples of acceptable broached ring and piston
Mecaer Aviation Group S.p.A. Proprietary Information
ALL INFORMATION CONTAINED IN OR DISCLOSED BY THIS DOCUMENT IS CONSIDERED CONFIDENTIAL AND PROPRIETARY BY MECAER AVIATION GROUP S.P.A..
ALL DESIGN, MANUFACTURE, USE, REPRODUCTION AND SALES RIGHTS ARE RESERVED BY MAG S.P.A.
MOD-PS-1-001 Rev.0
S.B. N°139-450 ALERT
DATE: April 20, 2016
Page 48 of 57  REVISION: C - April 10, 2018

### Page 49 (OCR)

ANNEX A  K LEONARDO  HELICOPTERS
IN SERVICE QUERY
MECAERIAVIATIONIGROUP  RECORD
S/N  S/N  S/ N  S/N  S/N  S/N  S/ N
64  830  1495  2228  5020  5911  6921
91  848  1497  2231  5055  5918  6935
117  851  1505  2236  5063  5947  6937
147  884  1507  2251  5100  5950  6944
148  901  1517  2255  5114  5961  6957
152  903  1530  2259  5126  5978  6958
161  917  1532  2267  5131  5990  6959
165  918  1540  2275  5153  5992  6969
167  920  1560  2277  5168  6022  6992
180  937  1562  2295  5187  6037  6994
183  957  1563  2296  5194  6081  7052
192  977  1565  2300  5196  6098  7062
193  992  1567  2315  5233  6113  7076
200  998  1579  2318  5245  6121  7089
201  1007  1580  2333  5250  6136  7113
202  1008  1586  2346  5273  6138  7123
223  1030  1590  2420  5283  6168  7130
224  1035  1600  2425  5285  6175  7131
233  1049  1604  2431  5304  6184  7132
264  1051  1656  2438  5307  6225  7133
266  1054  1667  2450  5308  6229  7160
267  1059  1673  2451  5310  6243  7180
276  1080  1691  2458  5312  6257  7199
306  1094  1714  2495  5340  6260  7202
320  1099  1739  2506  5349  6264  7243
330  1102  1742  2515  5365  6295  7273
336  1107  1745  2519  5367  6312  7412
349  1109  1747  2524  5369  6314  7462
361  1118  1767  2530  5385  6334  7478
366  1121  1781  2532  5414  6345  7490
396  1124  1786  2536  5422  6371  7491
414  1128  1796  2543  5466  6373  7492
420  1158  1797  2545  5495  6409  7493
424  1160  1799  2557  5498  6419  7534
431  1179  1813  2563  5508  6469  7578
447  1203  1824  2582  5519  6509  7598
453  1204  1848  2583  5521  6521  7621
473  1214  1856  2584  5528  6551  7635
476  1218  1857  2585  5536  6574  7645
484  1227  1860  2595  5545  6577  7646
490  1237  1870  2599  5556  6579  7648
492  1248  1871  2616  5571  6597  7654
498  1251  1884  2623  5589  6616  7674
515  1273  1888  2626  5594  6628  7678
550  1276  1897  2628  5600  6629  7690
572  1277  2629  5605  6645  7721
582  1279  1926  2632  5630  6646  7748
586  1283  1941  2640  5631  6658  7780
587  1305  1957  2656  5641  6659  7855
593  1317  1959  2662  5643  6660  7859
602  1325  1974  2676  5645  6662  7860
603  1328  1987  2677  5648  6673  7862
604  1330  1995  2680  5651  6675  7998
644  1364  2005  2695  5684  6738  8029
671  1371  2031  2697  5691  6739  8063
687  1379  2044  2700  5708  6740  8088
692  1384  2046  2702  5723  6742  8095
694  1394  2059  2704  5724  6769  8112
700  1396  2067  2710  5746  6780  8162
702  1398  2078  2711  5747  6781  8190
707  1421  2110  2719  5794  6786  8223
719  1427  2120  2751  5795  6826  8364
736  1429  2142  2756  5796  6838  8365
747  1447  2156  2771  5815  6882  8402
Mecaer Aviation Group S.p.A. Proprietary Information
ALL INFORMATION CONTAINED IN OR DISCLOSED BY THIS DOCUMENT IS CONSIDERED CONFIDENTIAL AND PROPRIETARY BY MECAER AVIATION GROUP S.P.A..
ALL DESIGN, MANUFACTURE, USE, REPRODUCTION AND SALES RIGHTS ARE RESERVED BY MAG S.P.A.
MOD-PS-1-001 Rev.0
S.B. N°139-450 ALERT
DATE: April 20, 2016
REVISION: C - April 10, 2018  Page 49 of 57

### Page 50 (OCR)

LEONARDO
ANNEX A  HELICOPTERS
IN SERVICE QUERY
MECAER | AVIATION I GROUP  RECORD
770  1448  2165  2777  5819  6888  8630
780  1458  2172  2786  5820  6889
783  1477  2197  2809  5824  6893
796  1484  2200  2845  5836  6896
797  1487  2206  2856  5868  6897
824  1494  2219  4836  5869  6906
Table 1 - List of S/N excluded from these instructions (confirmed having 60-80Nm applied)
Follow up required  • (see dedicated section below)
Signature
M.
Follow up
Ref. Document  Responsible
Name  Signature  Follow up Closing Date
Mecaer Aviation Group S.p.A. Proprietary Information
ALL INFORMATION CONTAINED IN OR DISCLOSED BY THIS DOCUMENT IS CONSIDERED CONFIDENTIAL AND PROPRIETARY BY MECAER AVIATION GROUP S.P.A.
ILL DESIGN, MANUFACTURE, USE, REPRODUCTION AND SALES RIGHTS ARE RESERVED BY MAG S.P.A
MOD-PS-1-001 Rev.0
S.B. N°139-450 ALERT
DATE: April 20, 2016
Page 50 of 57  REVISION: C - April 10, 2018

### Page 51

ANNEX B 
S
.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 51 of 57 
ANNEX B 
MR DAMPER EDDY CURRENT INSPECTION

### Page 52

ANNEX B 
 S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 52 of 57 REVISION: C - April 10, 2018 
REQUIRED EQUIPMENT 
For this inspection the following equipment is required: 
 E
ddy Current instrument model MIZ-21 SR manufactured by Zetec Inc. (US) (see NOTE 
below), 
 90° pencil, absolute shielded probe with frequency range 200kHz-2MHz (manufactured by 
VM Products Inc. USA with adaptor VM9 9Z21-M/H for Zetec instrument) and relevant 
cable (see NOTE below), 
 a flat calibration block be made in 15-5PH Steel with a reference notch of 0.5 mm depth 
manufactured by electro discharge machining (see figure B3), 
 adhesive PTFE tape to protect the tip of the probe from wear damage, 
 Solvent or aliphatic naphtha (C059). 
NOTE 
Other instruments and probes can be used provided that the following mandatory 
con
ditions are observed: 
 the probe is absolute and shielded type with central frequency range of 2.0MHz;  
 the system “instrument plus probe” shall obtain equivalent results from the calibration; 
 the setup is at least carried out by a Level 2 in accordance with EN4179/NAS410 and 
the relevant Work Instruction is approved by the Level 3 in accordance with 
EN4179/NAS410.

### Page 53

ANNEX B 
S
.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 53 of 57 
COMPLIANCE INSTRUCTIONS 
WARNING 
THE INSPECTIONS PERFORMED IN ACCORDANCE 
W
ITH THIS PROCEDURE SHALL BE CARRIED OUT 
BY PERSONNEL QUALIFIED AT LEAST LEVEL 2 IN 
THE EDDY CURRENT METHOD IN ACCORDANCE 
WITH THE REQUIREMENTS OF EN4179/NAS410. 
NOTE 
As required by PART I, PART II and PART III of this 
S
ervice Bulletin, the inspection areas are localised on 
the body end and rod end close to the spherical 
bearing. Refer to figures B1 and B2 to identify the 
areas on body end and rod end, respectively. 
CAUTION 
Make sure that the solvent does not come in contact 
w
ith the spherical bearing liner. 
1. Make sure that the whole surfaces of the areas of inspection are free from any grease, 
scale, conductive sealants or other excessive contaminants that can interfere with the 
inspections. If necessary, clean the surface on both sides with a clean cloth (C011) 
soaked with solvent. Let the solvent air dry. 
CAUTION 
During the inspection, it is important to: 
 
always maintain the probe as perpendicular as 
possible to the surface; 
 move it slowly and uniformly; 
 take care to the signal from the edge effect. 
2. Connect the probe on the instrument by relevant cable. 
3. Switch on the instrument and set up the parameters listed in figure B4. 
4. Perform instrument calibration as follows: 
NOTE 
The calibration shall be carried out before the 
i
nspection and rechecked after the end of the 
inspection; it shall be performed on the requested 
reference block in accordance with steps 4.1 thru 4.3. 
4.1 Put the sensor of the probe on the reference standard away from the notch.

### Page 54

ANNEX B 
 S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 54 of 57 REVISION: C - April 10, 2018 
4.2 Press the compensation key and adjust the phase of the instrument in a way that 
the lift-off signal results in horizontal deflection from the centre to the left, so that 
it is clearly distinguished from the defect indication (see trace A on Figure B4), 
4.3 Perform the scanning inspection on the reference block to verify that, in 
correspondence of the reference notch 0.5 mm deep, a vertical deflection signal 
and at least of four main divisions of the screen or at least 80% of full screen is 
obtained (see trace B on Figure B4). 
5. Perform the inspection as follows: 
NOTE 
Figures B1 and B2 are related to body end and rod 
en
d, respectively. Performing the inspection described 
in steps 5.1 thru 5.4, refer to the applicable figure for 
the component to be inspected. 
5.1 P ut the probe on the area identified “balancing/compensation” in figure B1 / B2 
and perform the balancing/compensation. Adjust the phase in a way that the lift-
off signal results in horizontal deflection. 
5.2 Perform the detailed examination on the inspection areas identified in figure B1 / 
B2 using circular path directions and, if possible, using the chamfering edge to 
drive the sensor. 
NOTE 
Each indication of crack is typically associated with a 
r
apid variation of the signal on the screen in the 
direction close to that due to the reference notch. 
5.3 Process and consider relevant any vertical deflection, unless it can be attri buted 
to lift-off or edge effect. If any vertical deflection is found, verify the instrument 
calibration and repeat the inspection to confirm the crack. 
5.4 Recheck the instrument calibration as described in step 4.

### Page 55

ANNEX B 
S
.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 55 of 57 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Areas of inspection and balancing for Body end 
Figure B1 
  
Upper side 
Balancing/compensation area 
Body end, inspection areas 
Lower side 
Body end, inspection areas 
Balancing/compensation area

### Page 56

ANNEX B 
 S
.B. N°139-450 ALERT 
 DATE: April 20, 2016 
Page 56 of 57 REVISION: C - April 10, 2018 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Areas of inspection and balancing for Rod end 
Figure B2 
Upper side 
Balancing/compensation area 
Rod end, inspection areas 
Balancing/compensation area 
Lower side 
Rod end, inspection areas

### Page 57

ANNEX B 
S
.B. N°139-450 ALERT 
DATE: April 20, 2016 
REVISION: C - April 10, 2018 Page 57 of 57 
 
 
REFERENCE STANDARD BLOCKS FOR EDDY CURRENT 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE 
 The dimensions are in mm with ± 0,7 mm of tolerances for all the dimensions a 
part from those of the notch (*) that shall be not higher than ± 0.02 mm; the 
surface shall be flat and parallel within ± 0.05 mm; the roughness shall be equal 
or better than 63 RMS. 
 The reference notch shall be carried out by machining or EDM 
 
 
 
Figure B3

### Page 58

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
