# Leonardo Bollettino Tecnico 139-465: Revision A

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2018-0737; AD 2019-12-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Bollettino Tecnico 139-465](https://openairdocs.org/service-documents/leonardo/sb-139-465.md)
- Title as filed: Leonardo BT 139-465 Rev A
- Pages: 37
- PDF: https://openairdocs.org/files/sha256/7a/16/7a166da8e0ca3bfb0c95d8d4933b6be58aaee81a6788a17ce297cde8f825cc70
- Page: https://openairdocs.org/service-documents/leonardo/sb-139-465/file/7a166da8e0ca

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

BOLLETTINO TECNICO N° 139-465 
The technical content of this document is approved 
under the authority of DOA nr. EASA.21J.005 DATE December 23, 2016 
REV. A - January 25, 2017 
Compliance with 
this Bulletin is: 
Page 1 of 36 
S
UBJECT 
TAIL ROTOR DRIVE SHAFT (TRDS) INTERFERENCE 
REASON 
To perform visual inspections of the number 1 drive shaft P/N 3G6510A01132 for 
evidence of scratches or indentations and to provide the necessary instructions to 
modify the rear exhaust module P/N 3G7810A00431 and the tunnel assy 
P/N 3G7130A13431 by means of the rear firewalls module retro modification 
P/N 3G7806P06412. 
HELICOPTERS AFFECTED 
AW139 helicopters S/Ns 31499, 31504, 31507, 31509, 31512, 31518, 31519, 
31524, 31529, 31533, 31535, 31536, 31537, 31538, 31539, 31540, 31541, 31542, 
31543, 31544, 31545, 31546, 31547, 31548, 31549, 31550, 31551, 31552, 31553, 
31554, 31555, 31556, 31557, 31558, 31559, 31560, 31561, 31562, 31563, 31564, 
31567, 31569, 31570, 31589, 41363, 41368, 41369, 41370, 41372, 41373, 41374, 
41375, 41378, 41381 and 41384. 
MANDATORY
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595

### Page 2

B.T. 139-465 Rev. A 
Page 2 of 36 
COMPLIANCE 
Part I: 
Within thirty (30) flight hours since receipt of th is Bollettino Tecnico and then 
every one hundred (100) flight hours until accomplishment of Part II. 
Part II: 
Within three hundred (300) flight hours since receipt of this Bollettino Tecnico. 
DESCRIPTION 
Few cases of number 1 drive shaft P/N 3G6510A01132 with evidence of scratches 
on external surface have been reported on AW139 helicopters.  
The investigations performed have demonstrated that , for AW139 helicopters 
equipped with rear exhaust module P/N 3G7810A00431,  tunnel assy 
P/N 3G7130A13431 and number 1 drive shaft P/N 3G651 0A01132, manufacturing 
and installation tolerances could not be sufficient to ensure the necessary clearance 
between the parts. 
Part I of this Bollettino provides the necessary in structions to perform visual 
inspections of the number 1 drive shaft P/N 3G6510A 01132 and, depending on 
findings, the replacement with a serviceable one. 
Part II of this Bollettino provides the necessary i nstructions to perform the retro 
modification of the rear exhaust module and of the tunnel assembly in order to 
increase the clearance between them and the tail rotor shaft. 
Present Revision A is issued to improve and clarify  the instructions for reworking of 
the defective area including a better identificatio n of the zones of the shaft that 
should be protected during the rework (ref. to step 7.3 of Part I). 
REQUIRED MANPOWER 
To comply with this Bollettino Tecnico the following Maintenance-Man-Hours (MMH) 
are deemed necessary: 
Part I:  approximately six (6) MMH. 
Part II: approximately twenty (20) MMH. 
Maintenance-Man-Hours are based on hands-on time an d can change with 
personnel and facilities available.

### Page 3

B.T. 139-465 Rev. A 
Page 3 of 36 
WARRANTY 
Owners/Operators who comply with the instructions of this Bulletin, no later than the 
applicable date in the “Compliance section”, will b e eligible to receive REQUIRED 
MATERIALS on free of charge basis, except for Consu mable Materials & Special 
Tools. 
NOTE: Customers who fail to comply with the instruc tions of this Bulletin before the 
compliance date are not eligible for the aforementioned special policy. 
Please issue relevant M.M.I.R. form ( (M)aintenance  (M)alfunction (I)nformation 
(R)eport ) to your Warranty Administration Dpt. 
REQUIRED MATERIALS 
The following materials are required for compliance with this Bollettino Tecnico: 
PART I 
The following consumable materials, or equivalent, are necessary to accomplish 
Part I of this Bollettino Tecnico: 
Spec./AW code number DESCRIPTION Q.TY NOTE 
TT-N-95-B / Code No. 
531055030 
Aliphatic Naphtha 
(C059) 
AR Local Supply 
Type No 670 Masking Tape (C077) AR Local Supply 
Scotch-Brite Abrasive pad (C015) AR Local Supply 
(1) 
Commercial Protective gloves AR Local Supply 
PART II 
P/N DESCRIPTION Q.TY NOTE 
3G7806P06412 REAR FIREWALLS RETRO 
MODIFICATION 
REF  
Composed of:    
3G7810P01331 REAR EXHAUST MODULE RETRO MODIFICATION REF (2) 
Composed of:    
3G7810A08951 Skin local enlarge cover rear LH ..1  
3G7810A09051 Skin local enlarge cover rear RH ..1

### Page 4

B.T. 139-465 Rev. A 
Page 4 of 36 
3G7810P01551 Stiffener LH reworked ..1  
3G7810P01651 Stiffener RH reworked ..1  
3G7810P01451 Plate ..4  
3G7106P10031 TUNNEL ASSY RETROMOD REF  
Composed of:    
3G7130A25951 Skin local enlarge cover front LH  ..1   
3G7130A26051 Skin local enlarge cover front RH ..1  
3G7130A26151 Seal ..2  
3G7130P00351 Reinforcement tunnel LH ..1  
3G7130P00451 Reinforcement tunnel RH ..1  
3G7130P00551 Reinforcement tunnel LH ..1  
3G7130P00651 Reinforcement tunnel RH ..1  
3G7130P00751 Reinforcement plate LH ..1  
3G7130P00851 Reinforcement plate RH ..1  
3G7130P00951 Reinforcement plate LH ..1  
3G7130P01051 Reinforcement plate RH ..1  
3G7130P01351 Reinforcement  ..2 (3) 
 
Moreover the following consumable materials, or equ ivalent, are necessary to 
accomplish Part II of this Bollettino Tecnico: 
Spec./AW code number DESCRIPTION Q.TY NOTE 
199-05-152 Type III / 
Code No. 
999999999000013871 
Adhesive RTV730 
(C125) 
AR Local Supply 
MIL-S-38249 Type I / 
Code No. 500203980 
Proseal 700 (C032) AR Local Supply 
MS20615-3M3 Rivet 0.3Kg  Local Supply 
MS20615-3M4 Rivet 0.1Kg Local Supply 
MS20615-3M3R Rivet 28 Local Supply 
MS20615-4M3 Rivet 0.1Kg  Local Supply 
NAS1200M3-3 
or NAS1200-3-3 
Rivet 80 or 
0.1Kg  
Local Supply 
NAS1200M3-3-5 Rivet 4 Local Supply 
NAS1200M4-4 Rivet 0.1Kg Local Supply

### Page 5

B.T. 139-465 Rev. A 
Page 5 of 36 
Spec./AW code number DESCRIPTION Q.TY NOTE 
NAS1200M3-4 Rivet 8 (4) 
Local Supply 
SPECIAL TOOLS 
The following special tools are required for compliance with this Bollettino Tecnico: 
PART I 
P/N DESCRIPTION Q.TY NOTE 
MIZ-21 SR Zetec Inc. Eddy Current instrument 
(or equivalent) 
1 (5) 
Commercial Depth Gauge 1 (6) 
Commercial Contact Point 1 (7) 
PART II 
N.A. 
NOTES: 
(1) Abrasive paper fine grain, 320 grit grade, P-C- 451 specification (C017) can 
be used as valid alternative. 
(2) P/N 3G7810A02033KIT or P/N 3G7810P00331 can be provided as a valid 
alternative to rear exhaust module retro modification P/N 3G7810P01331. 
(3) It is possible to obtain this part reworking th e reinforcement tunnel LH  
P/N 3G7130A29451 or RH P/N 3G7130A29551. 
(4) P/N NAS1200-3-4 may be supplied as a valid alte rnative. 
(5) Refer to Annex A for the complete list of the t ools necessary to perform the 
Eddy Current inspection. 
(6) The Depth Gauge shall be composed by: 
• dial indicator with a graduation of (at least) 0.0 1 mm 
(for reference only: Hoffmann P/N 434807 10) 
• base, compatible with the dial indicator, with a “ V” shape that allow 
measurement on a cylinder with a nominal diameter of 114.3 mm 
(for reference only: Hoffmann P/N L40010 8402)

### Page 6

B.T. 139-465 Rev. A 
Page 6 of 36 
(7) Contact point, compatible with the dial indicat or, with a conical shape with 
an angle of 45° and Max Head radius of 0.2mm. 
(for reference only: Hoffmann p/n 434900 13) 
WEIGHT AND BALANCE CHANGES 
Compliance with this Bollettino Tecnico has the fol lowing effects on helicopter 
weight and balance: 
PART I 
N.A. 
PART II 
WEIGHT (Kg) 0.207 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE  7743 1602.8 
LATERAL BALANCE -6.5 -1.35 
REFERENCES 
 AW139 Aircraft Maintenance Publication (AMP). 
 Annex A - 3G6510A00832 tube shaft n° 1 assy Eddy C urrent inspection. 
PUBLICATION AFFECTED 
 AW139 Illustrated Part Data (IPD).

### Page 7

B.T. 139-465 Rev. A 
Page 7 of 36 
COMPLIANCE INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components 
that are re-usable, including the attaching 
hardware that has been removed to gain 
access to the modification area and 
adequately protect them until their later re-
use. 
b) Exercise extreme care during drilling 
operations to prevent instruments, cables and 
hoses damage. 
c) After drilling, remove all debris and sharp 
edges. Apply on bare metal a light film of 
primer unless the hole is used for ground 
connection. 
d) Before rivet installation in places where 
fasteners were just removed, in accordance 
with the procedures reported on ASRP check 
hole diameter and if necessary install 
oversized rivets. If necessary install rivets with 
different grips. 
e) Protect properly all those equipments not 
removed from area affected by the 
modification during installation procedure. 
f) Let adhesive cure at room temperature for at 
least 24 hours unless otherwise specified. 
g) All lengths are in mm. 
PART I 
1. In accordance with AMP DM 39-A-00-20-00-00A-120A -A prepare the helicopter 
on ground for a safe maintenance. Disconnect the ba ttery, all electrical power 
sources and/or the external power supply.

### Page 8

B.T. 139-465 Rev. A 
Page 8 of 36 
2. In accordance with AMP DM 39-A-06-41-00-00A-010A -A open the access door 
310AL, the sliding fairing 473AL and remove the acc ess panel 471AL, 472AR, 
474BL, and 480AL. 
3. In accordance with AMP DM 39-C-78-10-01-00A-520A -A, remove the rear 
exhaust module from the helicopter. 
4. With reference to Figure 1, visual inspect the t ube shaft P/N 3G6510A00832 
(part of the number 1 drive shaft) for evidence of scratches or indentations in 
the indicated area rotating it, if necessary.  
4.1. If no scratches or indentations are detected, proceed as described in 
step 10. 
4.2. If scratches or indentations are detected, pro ceed as described in the 
following step 5. 
5. In accordance with AMP DM 39-B-65-11-01-00A-520A -A remove the number 1 
drive shaft P/N 3G6510A01132. 
6. In accordance with AMP DM 39-B-65-11-04-00A-520A -A remove the number 1 
flexible coupling P/N 4G6510V00151. 
7. With reference to Figure 1 position the number 1  drive shaft 
P/N 3G6510A01132 on a workbench and perform the tub e shaft 
P/N 3G6510A00832 rework as described in the following procedure: 
NOTE 
Clean and dry gloves shall be worn during cleaning 
and all the following operations. 
7.1. With reference to Figure 1, clean and degrease  the indicated area of the 
number 1 drive shaft P/N 3G6510A01132 by means of A liphatic Naphtha 
(C059). 
7.2. With reference to Figure 1, adequately mask th e tube/drive shaft to 
prevent the ingress of rework debris in critical areas. 
NOTE 
Machining operations are not allowed. 
For limits and surface roughness refer to Figure 1. 
7.3. With reference to Figure 1, smooth with wide r adius the defective area of 
the tube/drive shaft by means of Scotch-Brite or ab rasive paper fine grain

### Page 9

B.T. 139-465 Rev. A 
Page 9 of 36 
(320 grit grade) to completely remove scratches, to  break sharp edges 
and remove possible material swellings. Remove the less material quantity 
as possible. Do not exceed a maximum width of the r eworked area of 
10.00 mm as indicated in Figure 1. 
NOTE 
The maximum allowed depth of the 
scratch/indentation is 0.200 mm (0.079 in)  
7.4. With reference to Figure 2, perform a depth ch eck of the reworked area by 
means of a depth gauge, taking care of setting the “zero” of the gauge out 
of the reworked area indicated in Figure 1. 
7.5. If the measured depth of the scratch is higher  than 0.200 mm (0.079 in), in 
accordance with AMP DM 39-B-65-11-01-00A-520A-A and  
DM 39-B-65-11-01-00A-720A-A, replace number 1 drive  shaft 
P/N 3G6510A01132 and skip to Part II. 
7.6. If the measured depth of the scratch is lower than 0.200 mm (0.079 in), in 
accordance with the Annex A, perform the Eddy Curre nt inspection on the 
reworked area of the tube/drive shaft. 
7.7. If cracks are present, in accordance with AMP 
DM 39-B-65-11-01-00A-520A-A and DM 39-B-65-11-01-00 A-720A-A, 
replace number 1 drive shaft P/N 3G6510A01132 and s kip to Part II. 
Otherwise skip to step 7.8. 
7.8. Remove the masking from the tube/drive shaft. 
7.9. Mark the number DTRPTCM 11210016 by means of r ubber stamp and 
permanent ink near the reworked area of the tube sh aft 
P/N 3G6510A00832 of the number 1 drive shaft P/N 3G6510A01132. 
8. In accordance with AMP DM 39-B-65-11-04-00A-720A -A reinstall the number 1 
flexible coupling P/N 4G6510V00151. 
9. In accordance with AMP DM 39-B-65-11-01-00A-720A -A reinstall the number 1 
drive shaft P/N 3G6510A01132. 
10. In accordance with AMP DM 39-C-78-10-01-00A-720 A-A, install the rear 
exhaust module on the helicopter.

### Page 10

B.T. 139-465 Rev. A 
Page 10 of 36 
11. In accordance with AMP DM 39-A-06-41-00-00A-010 A-A close the access door 
310AL, the sliding fairing 473AL and reinstall the access panel 474BL. 
12. In accordance with AMP DM 39-A-06-41-00-00A-010 A-A reinstall the access 
panel 480AL, 471AL and 472AR. 
13. Return helicopter to flight configuration and r ecord for compliance with Part I of 
this Bollettino Tecnico on helicopter log book. 
14. Send the attached compliance form to: 
cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications  section on Leonardo AW 
Customer Portal and compile the “Technical Bulletin  Application 
Communication”.

### Page 11

B.T. 139-465 Rev. A 
Page 11 of 36 
PART II 
1. In accordance with AMP DM 39-A-00-20-00-00A-120A -A prepare the helicopter 
on ground for a safe maintenance. Disconnect the ba ttery, all electrical power 
sources and/or the external power supply. 
2. In accordance with AMP DM 39-A-06-41-00-00A-010A -A open the access door 
310AL, the sliding fairing 473AL and remove the acc ess panel 471AL, 472AR, 
474BL, and 480AL. 
3. In accordance with AMP DM 39-A-71-11-03-00A-520A -A remove the top 
forward cowl in order to get access to the work area. 
4. In accordance with AMP DM 39-C-78-10-01-00A-520A -A, remove the rear 
exhaust module P/N 3G7810A00431 from the helicopter. 
5. In accordance with AMP DM 39-C-78-10-04-00A-520A -A and 
DM 39-C-78-10-06-00A-520A-A, remove the left and th e right exhaust ducts 
from the helicopter. 
6. In accordance with AMP DM 39-C-78-10-01-01A-520A -B, remove the LH and 
the RH ejector assemblies from the rear exhaust module. 
NOTE 
Skip to step 10 if Rear Firewalls Module Assy  
P/N 3G7810A02033KIT or P/N 3G7810P00331 
has been provided. 
NOTE 
In order to avoid any damage on the helicopter, 
the following reworking procedure has to be 
performed on working bench. 
7. With reference to Figures 3 thru 6, rework rear exhaust module 
P/N 3G7810A00431 by means of the rear exhaust modul e retro modification 
P/N 3G7810P01331 as described in the following procedure: 
7.1 With reference to Figure 4 View A and Figure 5 View E, temporarily put in 
place the stiffener for mount rear exhaust LH P/N 3 G7810P01551 and the 
stiffener for mount rear exhaust RH P/N 3G7810P0165 1, coordinating with 
existing holes on the mount rear exhaust LH P/N 3G7 810A04651 and RH 
P/N 3G7810A05851. Mark position of n°34 rivet holes  on related mount

### Page 12

B.T. 139-465 Rev. A 
Page 12 of 36 
rear exhausts. 
7.2 With reference to Figure 4 View A and Detail C cut the mount rear exhaust 
LH P/N 3G7810A04651 and the mount rear exhaust RH 
P/N 3G7810A05851 coordinating with stiffener for mo unt rear exhaust LH 
P/N 3G7810P01551 and RH P/N 3G7810P01651. 
7.3 With reference to Figure 4 Section B-B, perform  a cut out on bend plate 
LH P/N 3G7810A04351 and RH P/N 3G7810A05551 coordin ating with 
skin local enlarge cover rear LH P/N 3G7810A08951 a nd RH 
P/N 3G7810A09051. If necessary, use Figure 11 to pe rform the cut, 
coordinating with mount rear exhaust existing holes. 
7.4 With reference to Figure 4 Section B-B, drill o ut the indicated existing 
rivets.  
7.5 With reference to Figure 5 View E, install stif fener for mount rear exhaust 
LH P/N 3G7810P01551 by means of n°6 rivets P/N MS20 615-3M3R and 
n°11 rivets P/N NAS1200M3-4 on mount rear LH. 
7.6 With reference to Figure 5 View E, install stif fener for mount rear exhaust 
RH P/N 3G7810P01651 by means of n°6 rivets P/N MS20 615-3M3R and 
n°11 rivets P/N NAS1200M3-4 on mount rear RH. 
7.7 With reference to Figure 5 View D and H and Fig ure 6 Section J-J, 
temporarily put in place the skin local enlarge cov er rear LH 
P/N 3G7810A08951 and RH P/N 3G7810A09051 and the n° 4 plates 
P/N 3G7810P01451. Mark position of n°26 rivet holes  of the skin local 
enlarge covers on bend plates. 
NOTE 
Apply sealant Proseal 700 (C032) on the mating 
surfaces of the skin local enlarge cover rear LH 
P/N 3G7810A08951 and RH P/N 3G7810A09051 
and the n°4 plates P/N 3G7810P01451 before 
their installation (ref. step 7.8). 
7.8 With reference to Figure 5 View H and Figure 6 Section J-J, install skin 
local enlarge cover rear LH P/N 3G7810A08951 and RH  
P/N 3G7810A09051 and the n°4 plates P/N 3G7810P0145 1 by means of

### Page 13

B.T. 139-465 Rev. A 
Page 13 of 36 
n°22 rivets P/N MS20615-3M3 and n°4 rivets P/N MS20615-3M4. 
7.9 With reference to Figure 6 Section J-J, seal al l around the edges of the 
skin local enlarge cover rear LH and RH P/N 3G7810A 08951 and 
P/N 3G7810A09051 and the n°4 plates P/N 3G7810P0145 1 by means of 
sealant Proseal 700 (C032). 
8. Temporarily relocate the rear exhaust module P/N  3G7810A00431 on the 
helicopter. 
9. Countermark position of the skin local enlarge c overs on the tunnel assy 
P/N 3G7130A13431, coordinating with those carried o ut with the rear exhaust 
module retromod, so creating reference points for the following steps. 
10. Temporarily remove the tunnel assy P/N 3G7130A1 3431 loosening the relevant 
turn locks. 
NOTE 
In order to avoid any damage on the helicopter, 
the following reworking procedure has to be 
performed on working bench (ref. step 11). 
11. With reference to Figures 3, 7 thru 10, rework tunnel assy P/N 3G7130A13431 
by means of the tunnel assy retromod P/N 3G7106P100 31, as described in the 
following procedure: 
11.1 With reference to Figure 7, remove the extrusi on rubber 
P/N A146A1606KB330 from the tunnel assy. 
11.2 With reference to Figure 7, remove the retaine r seal starboard 
P/N 3G7130A18251 and retainer seals P/N 3G7130A1815 1, drilling out 
existing rivet. 
11.3 With reference to Figure 7, perform the indica ted cut out on tunnel assy 
P/N 3G7130A13431, coordinating with skin local enla rge LH and RH 
P/N 3G7130A25951 and P/N 3G7130A26051, and their pr evious 
countermarked positions. If necessary, use Figure 1 2 to perform the cut, 
coordinating with stud turnlock fasteners existing holes. 
11.4 With reference to Figure 7 Detail J, install s kin local enlarge cover front LH 
P/N 3G7130A25951 and RH P/N 3G7130A26051 on the pro per 
installation position on tunnel assy P/N 3G7130A134 31, by means of n°36

### Page 14

B.T. 139-465 Rev. A 
Page 14 of 36 
rivets P/N NAS1200M3-3 and n°2 rivets P/N NAS1200M4-4. 
11.5 With reference to Figure 7 Section A-A, seal a ll around the edges of the 
skin local enlarge cover front LH P/N 3G7130A25951 and RH 
P/N 3G7130A26051 by means of sealant Proseal 700 (C032). 
11.6 With reference to Figure 8, Figure 9 Section E -E and Section D-D, 
temporarily locate reinforcement tunnel RH P/N 3G71 30P00451, 
reinforcement plate RH P/N 3G7130P00851, reinforcem ent tunnel RH 
P/N 3G7130P00651 and reinforcement plate RH P/N 3G7 130P01051. 
Countermark position of n°19 rivet holes in the tunnel assy. 
11.7 With reference to Figure 8, drill n°19 rivet h oles Ø 2.49÷2.59 in the 
previously marked positions. 
11.8 With reference to Figure 8, Figure 9 Section E -E and Section D-D, install 
reinforcement tunnel RH P/N 3G7130P00451, reinforce ment plate RH 
P/N 3G7130P00851, reinforcement tunnel RH P/N 3G713 0P00651 and 
reinforcement plate RH P/N 3G7130P01051 by means of  n°17 rivets 
P/N NAS1200M3-3 and n°2 rivets P/N NAS1200M3-3-5. 
11.9 With reference to Figure 8 and Figure 9 Sectio n B-B and Section C-C, 
temporarily locate reinforcement tunnel LH P/N 3G71 30P00351, 
reinforcement plate LH P/N 3G7130P00751, reinforcem ent tunnel LH 
P/N 3G7130P00551 and reinforcement plate LH P/N 3G7 130P00951. 
Countermark position of n°19 rivet holes in the tunnel assy. 
11.10 With reference to Figure 8, drill n°19 rivet holes Ø 2.49÷2.59 in the 
previously marked positions. 
11.11 With reference to Figure 8 and Figure 9 Secti on B-B and Section C-C, 
install reinforcement tunnel LH P/N 3G7130P00351, r einforcement plate 
RH P/N 3G7130P00751, reinforcement tunnel RH P/N 3G 7130P00551 
and reinforcement plate RH P/N 3G7130P00951 by mean s of n°17 rivets 
P/N NAS1200M3-3 and n°2 rivets P/N NAS1200M3-3-5. 
11.12 With reference to Figure 7 temporarily remove  n°2 ejector springs 
P/N A220ASN and n°2 stud turnlock fasteners P/N A242A01.

### Page 15

B.T. 139-465 Rev. A 
Page 15 of 36 
NOTE 
Proceed as described in step 11.13 only if  
reinforcement tunnel LH P/N 3G7130A29451 or 
RH P/N 3G7130A29551 has been provided. 
Otherwise skip to Step 11.14 
NOTE 
Refer to Figure 13 to rework the reinforcement 
tunnel LH P/N3G7130A29451. The rework from 
P/N 3G7130A29551 is symmetrical. 
11.13 Rework the reinforcement tunnel as described in the following procedure: 
11.13.1 With reference to Figure 13 View A and View  B, cut the indicated 
portions of the reinforcement tunnel. 
11.13.2 With reference to Figure 13 View B, mark th e reworked 
reinforcement tunnel to P/N 3G7130P01351. 
11.14 With reference to Figure 8 and Figure 9 Secti on F-F and Section G-G 
temporarily locate n°2 reinforcements P/N 3G7130P01 351 on the tunnel 
assy and countermark position of n°8 rivet holes ac cording to 
reinforcement tunnel LH P/N 3G7130P00351 and RH P/N  3G7130P00451 
and reinforcement tunnel LH P/N 3G7130P00551 and RH  
P/N 3G7130P00651. 
11.15 With reference to Figure 10 View From K, dril l n°18 rivet holes 
Ø 2.49÷2.59 in the previously marked positions. 
11.16 With reference to Figure 10 View From K and F igure 9 Section F-F and 
Section G-G install n°2 reinforcements P/N 3G7130P0 1351 by means of 
n°8 rivets P/N MS20615-3M3 and n° 10 rivets P/N NAS1200M3-3. 
NOTE 
It is possible to trim the reinforcement tunnel 
LH/RH (P/N 3G7130P00351 and 
P/N 3G7130P00451) and the reinforcement plate 
LH/RH (P/N 3G7130P00751 and 
P/N 3G7130P00851) in the case they are in 
interference with the ejector spring.

### Page 16

B.T. 139-465 Rev. A 
Page 16 of 36 
11.17 With reference to Figure 10 View From K reins tall n°2 ejector springs 
P/N A220ASN and n°2 stud turnlock fasteners P/N A24 2A01 as indicated 
by means of n°4 rivets P/N NAS1200M4-4. 
11.18 With reference to Figure 8 install n°4 rivets P/N MS20615-4M3 on the 
tunnel assy in the position of the removed ejector springs P/N A220ASN. 
11.19 With reference to Figure 8 and Figure 9 Secti ons B-B, C-C, D-D and 
Section E-E, bond n°2 seals P/N 3G7130A26151 to tun nel assy by means 
of adhesive RTV730. 
12. With reference to Figure 7, remark the reworked  tunnel assy as 
P/N 3G7106P10031 and reinstall it by means of the relevant turn locks. 
13. In accordance with AMP DM 39-C-78-10-04-00A-720 A-A and 
DM 39-C-78-10-06-00A-720A-A, install the left and t he right exhaust ducts on 
the helicopter. 
14. In accordance with AMP DM 39-C-78-10-01-01A-720 A-B, install the LH and the 
RH ejector assemblies to rear exhaust module. 
15. In accordance with AMP DM 39-C-78-10-01-00A-720 A-A, install the rear 
exhaust module on the helicopter. 
16. In accordance with AMP DM 39-A-71-11-03-00A-720 A-A install the top forward 
cowl. 
17. In accordance with AMP DM 39-A-06-41-00-00A-010 A-A close the access door 
310AL, the sliding fairing 473AL and reinstall the access panel 471AL, 472AR, 
474BL, and 480AL. 
18. In accordance with weight and balance changes, update the Chart A (see 
Rotorcraft Flight Manual, Part II, Section 6). 
19. Return helicopter to flight configuration and r ecord for compliance with Part II of 
this Bollettino Tecnico on helicopter log book. 
20. Send the attached compliance form to: 
cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications  section on Leonardo AW 
Customer Portal and compile the “Technical Bulletin  Application 
Communication”.

### Page 17

B.T. 139-465 Rev. A 
Figure 1 
Page 17 of 36 
REWORKABLE AREA
AREA TO BE PROTECTED
A1A1
AA

### Page 18

B.T. 139-465 Rev. A 
Figure 2 
Page 18 of 36

### Page 19

B.T. 139-465 Rev. A 
Figure 3 
Page 19 of 36

### Page 20

B.T. 139-465 Rev. A 
Figure 4 
Page 20 of 36

### Page 21

B.T. 139-465 Rev. A 
Figure 5 
Page 21 of 36

### Page 22

B.T. 139-465 Rev. A 
Figure 6 
Page 22 of 36

### Page 23

B.T. 139-465 Rev. A 
Figure 7 
Page 23 of 36

### Page 24

B.T. 139-465 Rev. A 
Figure 8 
Page 24 of 36

### Page 25

B.T. 139-465 Rev. A 
Figure 9 
Page 25 of 36

### Page 26

B.T. 139-465 Rev. A 
Figure 10 
Page 26 of 36

### Page 27

B.T. 139-465 Rev. A 
Figure 11 
Page 27 of 36

### Page 28

B.T. 139-465 Rev. A 
Figure 12 
Page 28 of 36

### Page 29 (OCR)

B.T. 139-465 Rev. A
3G7130A29451
REINFORCEMENT TUNNEL LH
B
R6.0
(TYP 2 PLCS)
85.5
VIEW A
97.5  INDICATED PORTION
R2.0
(TYP 4 PLCS)
CUT:  MARK TO:
INDICATED PORTION  R1.0  3G7130P01351  R1.0
REINFORCEMENT
VIEW B
3G7130P01351
REINFORCEMENT
Reinforcement maked from P/N 3G7130A29451.
The rework from P/N 3G7130A29551 is symmetrical.
Figure 13
Page 29 of 36

### Page 30

B.T. 139-465 Rev.A  ANNEX A 
 
Page 30 of 36 
 
 
 
 
 
 
A N N E X   A 
3G6510A00832 TUBE SHAFT N° 1 ASSY 
EDDY CURRENT INSPECTION

### Page 31

ANNEX A  B.T. 139-465 Rev.A 
 
 
 
Page 31 of 36 
 
REQUIRED EQUIPMENT 
For this inspection the following equipment is required: 
 Eddy Current instrument model MIZ-21 SR manufacture d by Zetec Inc. (US) (see NOTE 
below), 
 90° pencil, absolute shielded probe with high freq uency range (manufactured by VM 
Products Inc. USA with adaptor VM99Z21-M/H for Zete c instrument) and relevant cable (see 
NOTE below), 
 a flat calibration block made in Titanium Alloy Ti 6Al4V with a reference notches of 0.25 mm 
and 0.5mm depth manufactured by electro discharge machining (see Figure A2), 
 adhesive PTFE tape to protect the tip of the probe  from wear damage, 
 Class 2 solvent or aliphatic naphtha (C059). 
NOTE 
Other instruments and probes can be used provided t hat the following mandatory conditions 
are observed: 
 the probe is absolute and shielded type with centr al frequency range around 2.0÷3.0 MHz; 
 the system “instrument plus probe” shall obtain eq uivalent results from the calibration; 
 the setup is at least carried out by a Level 2 in accordance with EN4179/NAS410 and the 
relevant Work Instruction is approved by the Level 3 in accordance with EN4179/NAS410.

### Page 32

B.T. 139-465 Rev.A  ANNEX A 
 
Page 32 of 36 
 
COMPLIANCE INSTRUCTIONS 
WARNING 
THE INSPECTIONS PERFORMED IN ACCORDANCE 
WITH THIS PROCEDURE SHALL BE CARRIED OUT BY 
PERSONNEL QUALIFIED AT LEAST LEVEL 2 IN THE 
EDDY CURRENT METHOD IN ACCORDANCE WITH 
THE REQUIREMENTS OF EN4179/NAS410. 
NOTE 
The inspection area is localized on the external su rface of 
the tube shaft after reworking as indicated in PART  I of 
this Bollettino Tecnico. Refer to Figure A1 of this  Bollettino 
Tecnico to identify the inspection area. 
 
1. Make sure that the whole surfaces of the areas o f inspection are free from any grease, scale, 
conductive sealants or other excessive contaminants  that can interfere with the inspections. 
If necessary, clean the surface with a clean cloth (C011) soaked with solvent. Let the solvent 
air dry. 
CAUTION 
During the inspection, it is important to: 
• always maintain the probe as perpendicular as poss ible 
to the surface; 
• move it slowly and uniformly; 
 
2. Connect the probe on the instrument by relevant cable. 
3. Switch on the instrument and set up the paramete rs listed in Figure A3. 
4. Perform instrument calibration as follows: 
NOTE 
The calibration shall be carried out before the ins pection 
and rechecked after the end of the inspection; it s hall be 
performed on the requested reference block in accordance 
with steps 4.1 thru 4.3. 
4.1. Put the sensor of the probe on the reference standard away from the notch.

### Page 33

ANNEX A  B.T. 139-465 Rev.A 
 
 
 
Page 33 of 36 
 
4.2. Press the compensation key and adjust the phase of the instrument in a way that the lift-
off signal results in horizontal deflection from th e centre to the left, so that it is clearly 
distinguished from the defect indication (see trace A on Figure A3), 
4.3. Perform the scanning inspection on the reference block to verify that, in correspondence 
of the reference notches 0.5 and 0.25 mm deep, a ve rtical deflection signals at least of 
respectively four (4) and one (1) main divisions of  the screen are obtained (see traces B 
and C on Figure A3). 
5. Perform the inspection as follows: 
5.1. Put the probe on the area identified “balancin g/compensation” in Figure A1 and perform 
the balancing/compensation. Adjust the phase in a w ay that the lift-off signal results in 
horizontal deflection. 
5.2. Perform the detailed examination on the inspec tion areas identified in Figure A1 after 
reworking using longitudinal paths direction and indexing of 2mm and covering the whole 
circumference. 
NOTE 
Each indication of crack is typically associated with a rapid 
variation of the signal on the screen in the direct ion close 
to that due to the reference notches. 
5.3. Process and consider relevant any vertical deflection, unless it can be attributed to lift-off. 
If any vertical deflection is found, verify the instrument calibration and repeat the inspection 
to confirm the crack. 
5.4. Recheck the instrument calibration as described in step 4.

### Page 34

B.T. 139-465 Rev.A  ANNEX A 
 
Page 34 of 36 
 
 
 
Areas of inspection and balancing for tube shaft N°1 assy 
 
Figure A1 
Scanning path 
direction

### Page 35

ANNEX A  B.T. 139-465 Rev.A 
 
 
 
Page 35 of 36 
 
 
REFERENCE STANDARD BLOCKS FOR EDDY CURRENT 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE 
 
• The dimensions are in mm with ± 0,7 mm of toleranc es for all the dimensions apart from 
those of the notches (*); the surface shall be flat and parallel within ± 0.05 mm; the 
roughness shall be equal or better than 63 RMS. 
• The reference notches shall be carried out by mach ining or EDM 
 
 
Figure A2 
0.25 and 0.5 mm (*) 
(*) 
0.15 mm max

### Page 36 (OCR)

B.T. 139-465 Rev.A  ANNEX A
SETUP PARAMETERS FOR THE ZETEC "MIZ-21 SR" INSTRUMENT
90° absolute and shielded probe
EC F1  TEST  DISP1  SRC F1  ALM SRC  D1
SETUP#  #30  MODE  X-Y  ALARM  IN
CONFIG NAME  VM215F TITA  V SCALE D1  01  CHNG  CENT
FREQ1  3.0M  H SCALE D1  07  CHNG  SIZE
DIFFR F1  008  PHASE D1  200 (horizontal,  OUTPUT  S
as necessary)
GAIN F1  55  POSITION D1  neglect  STOR  SCNO
MARK/CLR  # 0  LPS  000 310  RULER  OFF
AUTOSET  F1  SCREEN A  ON  ILCD  ADJ
EC F1 TEST DISP1 SRC FI ALM SROD1
VM215F TITA USCALE D1 01 CHNG CENT
OM HSCALE D1 07 CHNG SIZE
DIFFE F1 008 PHASE D1 200 OUTPUTS
GAIN  F1  - 55  POSITION D1  STOR
MARKYCLR  LPS  000  S10 RULER OFF
AUTOSET  FIPAUTOCLEAR › LCD  ADV
CAUTOCLEAR ONZOFE  D1:H-151V-031
BEER PERSISTENCE HHH 2500 SAM/S
Typical signal from the calibration (A = lift-off signal, B = indication from reference notch 0.5
mm deep, C = indication from reference notch 0.25 mm deep).
Figure A3
Page 36 of 36

### Page 37

Remarks:
Information: 
 BOLLETTINO TECNICO COMPLIANCE FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
