# Leonardo Emergency Alert Service Bulletin 139-508: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2017-0939; AD 2018-03-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Emergency Alert Service Bulletin 139-508](https://openairdocs.org/service-documents/leonardo/sb-139-508.md)
- Title as filed: Leonardo Helicopters SB Emergency Alert 139-508
- Pages: 14
- PDF: https://openairdocs.org/files/sha256/ad/f4/adf419ebbe43c07ab1b7e564d8ee4dc814f012c2539115eeaeeed48bc392bcf6
- Page: https://openairdocs.org/service-documents/leonardo/sb-139-508/file/adf419ebbe43

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N° 139-508
DATE:  September 12, 2017 
REV. : /-March 3, 2017 
Page 1 of 13 
TITLE 
ATA 62 – MAIN ROTOR BLADE TIP CAP INSPECTION 
REVISION LOG 
New Issue 
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
EMERGENCY ALERT
SERVICE BULLETIN

### Page 2

S.B. N°139-508 EMERGENCY ALERT 
 DATE: September 12, 2017 
Page 2 of 13 REVISION: / 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
AW139 helicopters equipped with Main Rotor Blade (MRB) P/N 3G6210A00131 
having S/N listed in Table 1. 
NOTE 
This Service Bulletin is not applicable to MRB having a 
S/N with the letter “R” as the final digit. 
S/N 
3615 
3634 
3667 
3729 
TABLE 1 
NOTE 
If any of the above MRB is in stock, please contact 
cse.aw139.aw@leonardocompany.com to obtain 
information on how to handle the parts. 
B. COMPLIANCE 
Part I 
Within five (5) flight hours since the date of issuance of this Service Bulletin. 
Part II 
 Before the first flight after accomplishment of Part I, in case debonding is found 
complying with Part I. 
 Within ten ( 10) flight hours since the date of issuance of this Service Bulletin, in case 
no debonding is found complying with Part I. 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin is issued in order to provide the necessary instruction to perform 
the inspection of the tip cap installed on a defined batch of main rotor blades

### Page 3

S.B. N°139-508 EMERGENCY ALERT 
DATE: September 12, 2017 
REVISION: / Page 3 of 13 
P/N 3G6210A00131, in order to detect potential debonding , and the replacement of 
the affected component as terminating action. 
E. DESCRIPTION 
A case of debonding of the tip cap P/N 3G6210A05331 from the MRB  
P/N 3G6210A00131 has been reported on an AW139 helicopter, this resulting in the 
loss of the tip cap in flight. This event did not compromise the conduct of flight. 
The investigation has identified as cause of the occurrence the incorrect bonding 
procedures during the manufacturing of some main rotor blades. 
Leonardo Helicopters, as precautionary measure, issued this Service Bulletin to 
perform a tapping test (Part I) in order to detect potential debonding and to perform the 
replacement of the MRB (Part II). 
F. APPROVAL 
The content of this Service Bulletin is approved under the authority of DOA nr. 
EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If a helicopter listed in the effectivity embodies a modification or repair not LHD 
certified and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin the following MMH are deemed necessary: 
Part I: approximately one (1) MMH; 
Part II: approximately four (4) MMH. 
MMH are based on hands-on time and can change with personnel and facilities 
available. 
H. WEIGHT AND BALANCE 
N.A.

### Page 4

S.B. N°139-508 EMERGENCY ALERT 
 DATE: September 12, 2017 
Page 4 of 13 REVISION: / 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE DESCRIPTION 
DM01 39-A-00-20-00-00A-120A-A Helicopter on ground for a safe 
maintenance. 
DM02 39-A-62-11-01-00A-520A-A Main rotor blade - Remove procedures 
DM03 39-A-62-11-01-00A-720A-A Main rotor blade - Install procedures 
DM04 39-A-GF-05-00-00A-066A-A Hammer (steel) M/R and T/R blades 
tapping insp. (GF-05-00) 
DM05 39-A-GF-06-00-00A-066A-A Hammer (alum) M/R and T/R blades 
tapping insp. (GF-06-00) 
2) ACRONYMS 
AMP Aircraft Maintenance Publication 
DOA Design Organization Approval 
DM Data Module 
EASA European Aviation Safety Agency 
ITEP Illustrated Tools and Equipment Publication 
LHD Leonardo Helicopter Division 
LS Local Supply 
MMH Maintenance-Man-Hours 
MMIR Maintenance Malfunction Information Report 
MRB Main Rotor Blade 
WRM Warranty Reply Memo 
3) ANNEX 
Annex A Hammer Tapping Inspection - AW139 Tip-Cap 
J. PUBLICATIONS AFFECTED 
N.A. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 5

S.B. N°139-508 EMERGENCY ALERT 
DATE: September 12, 2017 
REVISION: / Page 5 of 13 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
PART II 
P/N DESCRIPTION Q.TY NOTE 
3G6210A00131 MRB AR  
2) CONSUMABLES 
The following consumable materials, or equivalent, are necessary to accomplish this 
Service Bulletin: 
Spec./AW code number DESCRIPTION Q.TY NOTE PART 
Commercial Lint-free cloth (C011) AR LS I 
MIL-PRF-680C, Type II Cleaning solvent (C010) AR LS I 
MIL-C-25769H Cleaning compound (C018) AR LS I 
B. SPECIAL TOOLS 
P/N DESCRIPTION Q.TY NOTE PART 
109-3101-58-1 or  
109-3101-58-2 or 
equivalent 
Tapping hammer  
(GF-05-00) or (GF-06-00) 
1  I 
/ Magnifying glass (10 power) 1 LS I 
C. INDUSTRY SUPPORT INFORMATION 
WARRANTY: Owners/Operators who comply with the instructions of this Service 
Bulletin no later than the applicable date in the “Compliance” section will be eligible to 
receive REQUIRED MATERIALS on free of charge basis, except for Consumable 
Materials and Special Tools.  
NOTE: Customers who fail to comply with the instructions in this Service Bulletin 
before the compliance date are not eligible for the aforementioned special policy.  
Please Issue relevant MMIR form to your Warranty Administration Dpt.  
NOTE: WRM will include RETURN MATERIAL AUTHORIZATION (RMA) number; the 
unit disembarked (P/N 3G6210A00131 MRB) from the aircraft has to be returned to 
LHD within thirty (30) calendar days after the shipment of the replacement part. In 
case of missing return within thirty (30) calendar days, Customer will be invoiced for 
the price of the replacement part.

### Page 6

S.B. N°139-508 EMERGENCY ALERT 
 DATE: September 12, 2017 
Page 6 of 13 REVISION: / 
NOTE: The S/N and INSPECTION REPORT are mandatory; in case the MMIR is not 
accompanied by these documents, it will be rejected.

### Page 7

S.B. N°139-508 EMERGENCY ALERT 
DATE: September 12, 2017 
REVISION: / Page 7 of 13 
3. ACCOMPLISHMENT INSTRUCTIONS 
PART I 
1. In accordance with AMP DM 39-A- 00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery , all electrical power sources 
and/or the external power supply. 
2. Gain access to the affected MRB P/N 3G6210A00131. 
NOTE 
The authorized personnel who will carry out the test 
must comply with the requirements listed in Annex A. 
3. In accordance with Annex A and with reference to Figure 1, perform a tapping test on 
the identified area of MRB. 
4. In case no debonding is found, proceed with step 6. 
5. In case debonding is found, apply Part II of this Service Bulletin to replace the affected 
MRB before next flight. Send the MRB you have removed to LHD for tip cap 
replacement and MRB assembly S/N remarking with letter “R” after last digit. 
6. Return the helicopter to flight configuration and record for compliance with Part I of this 
Service Bulletin on the helicopter logbook and on the component logcard. 
7. Send the attached compliance form to the following mail box: 
 cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 8

S.B. N°139-508 EMERGENCY ALERT 
 DATE: September 12, 2017 
Page 8 of 13 REVISION: / 
PART II 
1. In accordance with AMP DM 39-A- 00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery , all electrical power sources 
and/or the external power supply. 
2. In accordance with AMP DM 39-A- 62-11-01-00A-520A-A and DM 39-A- 62-11-01-00A-
720A-A, replace the affected MRB P/N 3G6210A00131 with a serviceable one not 
affected by this Service Bulletin. Send the MRB you have removed to LHD for tip cap 
replacement and MRB assembly S/N remarking with letter “R” after last digit. 
3. Return the helicopter to flight configuration and record for compliance with Part II of this 
Service Bulletin on the helicopter logbook. 
4. Send the attached compliance form to the following mail box: 
 cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 9 (OCR)

« LEONARDO  HELICOPTERS
LEADING EDGE  EROSION  EROSION
FAIRING  HONEYCOMB CORE  SHIELD  SHIELD
COVER  LIGHTNING  BONDING STRIP  SPAR  LEADING  EDGE
TRAILING  A TIP
TRAILING EDGE  FAIRING  EDGE  TRIM TAB  TRIM TAB  CAP
VOIDS NOT
PERMITTED IN
THIS AREA
COVER
STA 6300
STA 6400
HAMMER TAPPING IS REQUIRED
ON BOTH UPPER AND LOWER SIDES
AND NOSE OF THE BLADE
Figure 1
S.B. N°139-508 EMERGENCY ALERT
DATE: September 12, 2017
REVISION: /  Page 9 of 13

### Page 10

Figure 2 
 S.B. N°139-508 EMERGENCY ALERT 
 DATE: September 12, 2017 
Page 10 of 13 REVISION: / 
 
 
 
 
 
 
 
 
 
Page intentionally left blank

### Page 11

S.B. N°139-508 EMERGENCY ALERT  
DATE: September 12, 2017  
REVISION: / Page 11 of 13 
ANNEX A 
HAMMER TAPPING INSPECTION 
AW139 TIP-CAP

### Page 12

ANNEX A 
 S.B. N°139-508 EMERGENCY ALERT 
 DATE: September 12, 2017 
Page 12 of 13 REVISION: / 
 
SPECIFIC REQUIREMENTS OF INSPECTION 
Carry out hammer tapping inspection with hammer P/N 109-3101-58-1 or P/N 109-3101-
58-2 of both upper and lower sides and nose of the blade to detect potential debonding. 
Report results. 
 
GENERAL REQUIREMENTS 
1. PERSONNEL AUTHORIZATION REQUIREMENTS 
In order to be authorized to carry out hammer tapping inspections, the assigned 
personnel shall: 
 have passed the near vision examination and colour perception requirements 
specified in EN4179 / NAS410; 
 have passed an audiometric test which  consists of a test at 500, 1000, 2000 and 
3000 Hz frequencies with the following acceptance criteria: 
a. average maximum loss of 30 dB at the four frequencies; 
b. maximum loss of 50 dB at every single frequency; 
NOTE 
The above requirements shall be considered as a 
minimum; other tests and requirements based on local 
national health and safety protection rules are 
acceptable on condition that the above requirements 
are satisfied or exceeded. 
 have a minimum of 40 hours of documented practical experience obtained under the 
direct supervision of personnel having previous authorization in hammer tapping 
inspection; 
 have knowledge of the type of structure to be tested in order to be aware of the 
change of sound due to the configuration/lay-up of the part, such as, but not limited 
to: 
- different thickness of the top layers, 
- overlap areas, 
- inserts, 
- changes to the geometrical form of the part, 
- edge effects, 
- changes to the distance between supports and fasteners, 
- changes to the thickness of adhesive, 
- areas with sealant,

### Page 13

ANNEX A 
S.B. N°139-508 EMERGENCY ALERT 
DATE: September 12, 2017 
REVISION: / Page 13 of 13 
- changes to the type of honeycomb, 
- areas with core filler or splice adhesive. 
 be aware of the change of sound on a specific structure when it is defective and 
when it is sound. 
2. MAINTENANCE OF AUTHORIZATION 
In order to maintain the authorization to carry out hammer tapping inspections, the 
assigned personnel shall repeat with annual frequency the tests reported at steps no.1.1  
and no. 1.2 in paragraph no.1. 
3. HAMMER TAPPING 
The hammer shall comply with the requirements of P/N 109-3101-58-1 (steel hammer, 
GF-05-00) or P/N 109-3101-58-2 (aluminium hammer, GF-06-00). Refer to ITEP DM 39-
A-GF-05-00-00A-066A-A and DM 39-A-GF-06-00-00A-066A-A. 
4. PROCEDURE 
4.1 Clean the tip cap following the instructions below: 
4.1.1 Clean the tip cap with the lint-free cloth (C011) and the cleaning solvent 
(C010). 
4.1.2 Wash the tip cap with the cleaning compound (C018). 
4.1.3 Rinse the tip cap with water. 
4.1.4 Dry the tip cap with the compressed air. 
CAUTION 
The inspection shall be carried out by qualified 
personnel. 
NOTE 
With 'VOIDS' we identify the not bonded area between 
the surfaces of a component. The primary causes are: 
unwanted materials between the surface and the 
adhesive, air bubbles, missing adhesive and other 
damage. 
4.2 Do the inspection of the tip cap bonded area for VOIDS by 'tapping' its surface  (both 
upper and lower sides) with a tapping hammer (P/N 109-3101-58-1 or P/N 109-
3101-58-2 or equivalent). The tapping frequency must make  a continuous tone that 
helps you to identify the tone change immediately. Be careful when you do the 
tapping operation to prevent damage to the bl ade surface. The area of voids you 
find must be correctly identified with a mark on the contour of the damage.

### Page 14

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
