# Leonardo Alert Service Bulletin 139-533: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2020-0215; AD 2020-15-18 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 139-533](https://openairdocs.org/service-documents/leonardo/sb-139-533.md)
- Title as filed: Leonardo ASB 139-533
- Pages: 23
- PDF: https://openairdocs.org/files/sha256/7f/06/7f069dea2d0b28cceb8121317ce1f95a4a07b2241ab7aa62b5731bfa4e8d4af6
- Page: https://openairdocs.org/service-documents/leonardo/sb-139-533/file/7f069dea2d0b

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N°  139-533 
DA TE:  August 30, 2018 
REV. :  / - / 
Pa ge 1 of 22 
TITLE
ATA 95 – EFS AFT FLOAT ASSY INFLATION SYSTEM RESET PR OCEDURE 
REVISION LOG 
First Issue 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S.B. N°139-533 ALERT 
 DATE: August 30, 2018 
Page 2 of 22 REVISION: / 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
SMA inflation system P/N 3G9560V01052 up to S/N 1801 included (except S/N 1783 
and S/N 1784), in stock or fitted on the float assemblies P/N 3G9560V00332, P/N 
3G9560V00432, P/N 3G9560V01432, P/N 3G9560V01532, both installed on 
AB139/AW139 aircraft or kept in stock. 
NOTE 
SMA inflation systems are NOT affected if they have 
the Service Bulletin SB-139-25-002 marked on the 
body of the SMA actuation device (pin-puller)  
P/N P-H20006 (shown in Figure 1 of the  
SB-139-25-002 in Annex A) even if they have a S/N 
listed above. 
NOTE 
SMA inflation systems not affected are installed on 
float assemblies (part of kit EFS P/N 3G9560F00111 or 
P/N 3G9560F00113) with the S/N listed below: 
DESCRIPTION P/N S/N 
AFT LH float assy 
(textile cover) 
3G9560V00332 from S/N 405 
included 
AFT RH float assy 
(textile cover) 
3G9560V00432 S/N 399 and from 
S/N 402 included 
AFT LH float assy 
(rigid cover) 
3G9560V01432 S/N 492 and from 
S/N 494 included 
AFT RH float assy 
(rigid cover) 
3G9560V01532 S/N 469 and from 
S/N 472 included 
This Service Bulletin is not applicable to float 
assemblies having the Service Bulletin SB-139-25-002 
marked on the float assembly log card, even if they 
don’t have a S/N listed above.

### Page 3

S.B. N°139-533 ALERT 
DATE: August 30, 2018 
REVISION: / Page 3 of 22 
B. COMPLIANCE 
• Within one hundred (100) FH since the date of issuance of this Service Bulletin for 
components installed on AB139/AW139 helicopters. 
• Before the first installation on the helicopter for components kept in stock. 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin is issued to prescribe a one-off reset procedure of the EFS SMA 
actuation device. 
E. DESCRIPTION 
Investigation following few cases of inadvertent float deployment led the supplier to 
find that improper reset may have been performed on the SMA actuation device, 
leading to a not stable condition of the system. To avoid this possibility, an improved 
reset procedure has been defined and is now used in production and in authorized 
service stations for overhaul activities. 
This Service Bulletin is issued to prescribe the one-off reset of all the inflation systems 
manufactured and delivered before implementation of the new procedure. 
This activity requires the inflation system removal from the AFT float and could be 
performed by operators entitled to remove/install the float assemblies from the aircraft 
or by the authorized service stations. 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin.

### Page 4

S.B. N°139-533 ALERT 
 DATE: August 30, 2018 
Page 4 of 22 REVISION: / 
G. MANPOWER 
To comply with this Service Bulletin the following MMH are deemed necessary: 
• one (1) MMH for the reset procedure; 
• six (6) MMH to remove and install the AFT float assemblies. 
MMH are based on hands-on time and can change with personnel and facilities 
available. 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE DESCRIPTION PART 
DM01 39-A-00-20-00-00A-120A-A Helicopter on ground for a safe 
maintenance 
- 
DM02 39-A-06-41-00-00A-010A-A Access doors and panels - 
DM03 39-A-95-61-03-00A-520A-K AFT left float assembly - Remove 
procedure 
- 
DM04 39-A-95-61-03-00A-720A-K AFT left float assembly - Install 
procedure 
- 
DM05 39-A-95-61-04-00A-520A-K AFT right float assembly - 
Remove procedure 
- 
DM06 39-A-95-61-04-00A-720A-K AFT right float assembly - Install 
procedure 
- 
DM07 39-A-95-61-05-00A-520A-K Bottle assembly - Removal - 
DM08 39-A-95-61-05-00A-720A-K Bottle assembly - Installation - 
 
2) ACRONYMS 
AMDI Aircraft Material Data Information 
AMP Aircraft Maintenance Publication 
DM Data Module 
EFS Emergency Floatation System 
ITEP Illustrated Tools and Equipment Publication 
MMH Maintenance Man Hours 
MMIR Maintenance Malfunction Information Report 
SMA Shaped Memory Alloy

### Page 5

S.B. N°139-533 ALERT 
DATE: August 30, 2018 
REVISION: / Page 5 of 22 
3) ANNEX 
Annex A AEROSEKUR SERVICE BULLETIN SB-139-25-002 
J. PUBLICATIONS AFFECTED 
N.A. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 6

S.B. N°139-533 ALERT 
 DATE: August 30, 2018 
Page 6 of 22 REVISION: / 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
N.A. 
1) PARTS 
N.A. 
2) CONSUMABLES 
Refer to AMDI for the consumable required to comply with the AMP DM referenced 
in the accomplishment instructions and to paragraph 2.A of SB-139-25-002 in  
Annex A. 
3) LOGISTIC MATRIX 
N.A. 
B. SPECIAL TOOLS 
Refer to ITEP for the special tools required to comply with the AMP DM referenced in 
the accomplishment instructions and to paragraph 2.B of SB-139-25-002 in Annex A. 
C. INDUSTRY SUPPORT INFORMATION 
In order to allow all Customers to accomplish this Service Bulletin within the relevant 
compliance time and to minimize the impact on their operations, Leonardo Helicopters 
has developed a dedicated distribution plan for the specific tools according to the 
geographical distribution of the involved Customers and taking into account the 
average utilization profile of the associated helicopters. Given that, Leonardo 
Helicopters kindly invite all the potentially affected Customer / Operator / Service 
Centre to get in contact with their usual Leonardo Helicopters Logistic Administrator to 
receive instructions about the purchase policy for this Service Bulletin.

### Page 7

S.B. N°139-533 ALERT 
DATE: August 30, 2018 
REVISION: / Page 7 of 22 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
Place an identification tag on all components that are 
re-usable, including the attaching hardware that has 
been removed to gain access to the modification area 
and adequately protect them until their later re-use. 
NOTE 
Skip steps 1 and 2 if the affected inflation system is 
installed on an AFT float assembly kept in stock. 
Skip steps 1 thru 3 if the affected inflation system is 
kept in stock. 
1. In accordance with AMP DM 39-A-00-20-00-00A-120A- A prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
NOTE 
Apply following step 2 on LH float assembly or RH float 
assembly or both float assemblies in accordance with 
the effectivity. 
2. In accordance with AMP DM 39-A-95-61-03-00A-520A- K and/or                                    
DM 39-A-95-61-04-00A-520A-K remove the AFT left float assembly and/or AFT right 
float assembly. 
3. In accordance with AMP DM 39-A-95-61-05-00A-520A-K remove the inflation system 
from the relevant AFT float assembly. 
WARNING 
PRIOR TO ACCOMPLISH THE RESET PROCEDURE 
AT FOLLOWING STEP 4, ENSURE TO HAVE SEEN 
AND UNDERSTOOD ALL THE INSTRUCTIONS 
SHOWN IN THE SELF-TRAINING VIDEO TUTORIAL, 
AVAILABLE ON LEONARDO WEBPORTAL AND ON 
AEROSEKUR WEBPORTAL. 
IF DOUBT EXISTS, PLEASE CONTACT 
AEROSEKUR TO: 
PRODUCT-SUPPORT@SEKUR.AERO. 
4. Perform the inflation system reset procedure acco rding to paragraph 3 of  
SB-139-25-002 in Annex A.

### Page 8

S.B. N°139-533 ALERT 
 DATE: August 30, 2018 
Page 8 of 22 REVISION: / 
5. Record for compliance with Service Bulletin SB-139-25-002 on the inflation system pin-
puller according to paragraph 3 of SB-139-25-002 in Annex A. 
NOTE 
Following steps 6 thru 9 are not required if the inflation 
system must be kept in stock. 
CAUTION 
Replacement of the inflation system with another one 
not compliant with this Service Bulletin is not allowed. 
6. In accordance with AMP DM 39-A-95-61-05-00A-720A- K install the inflation system on 
the relevant AFT float assembly. 
7. Record for compliance with Service Bulletin SB-139-25-002 on the AFT float assembly 
logcard. 
NOTE 
Following steps 8 and 9 are not required if the AFT 
float assembly must be kept in stock. 
8. In accordance with AMP DM 39-A-95-61-03-00A-720A- K and/or                                   
DM 39-A-95-61-04-00A-720A-K install the AFT left float assembly and/or the AFT right 
float assembly removed at step 2. 
9. Return the helicopter to flight configuration and record for compliance with this Service 
Bulletin on the helicopter logbook. 
10. Send the attached compliance form to the following mail box: 
     cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”

### Page 9

ANNEX A 
S.B. N°139-533 ALERT 
DATE: August 30, 2018 
REVISION: / Page 9 of 22 
ANNEX A 
AEROSEKUR SERVICE BULLETIN SB-139-25-002

### Page 10 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
28 June 2018
HIGHLIGHTS
REVISION TRANSMITTAL
This sheet transmits Revision 1 to SB-139-25-002, which:
A. Change the Inspection and Modification paragraph with the addition of
caution notes and information in case reset procedure fails (identified by
revision bar).
NOTE: This revision replaces the original issue of SB-139-25-002 in its
entirety.
REVISION COMPLIANCE
NO EFFECT. SMA Inflation System P/N 302444A (LHD P/N 3G9560V01052)
previously modified by the original issue of this Service Bulletin are not affected
by this revision.
LOG OF REVISIONS
Original Issue  28 May 2018
Revision 1  28 June 2018
S.B. N°139-533 ALERT
DATE: August 30, 2018
Page 10 of 22  REVISION: /

### Page 11 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
28 June 2018
HIGHLIGHTS
PAGE INTENTIONALLY BLANK
S.B. N°139-533 ALERT
DATE: August 30, 2018
REVISION: /  Page 11 of 22

### Page 12 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
1. PLANNING INFORMATION
A. TITLE
ATA 25 - Equipment Furnishings - Emergency Flotation System (EFS) - Mandatory inspection of
actuation device P/N P-H20006.
B. EFFECTIVITY
This Service bulletin affects each SMA Inflation System P/N 302444A (LHD P/N 3G9560V01052) up
to S/N 1801 included (except S/N 1783 and S/N 1784), in stock or fitted on the Float Assemblies of
the following table, both installed on AB139/AW139 helicopters or kept in stock.
Table 1 lists the part numbers of Emergency Flotation Systems for AB139/AW139 Helicopter
equipped with the SMA Inflation systems affected.
DESCRIPTION  LHD P/N  AERO SEKUR P/N  S/N
AFT Left Float Assy  3G9560V00332  303491A  Up to S/N 404 included
(Textile Cover)
AFT Right Float Assy  3G9560V00432  303492A  Up to S/N 401 included
(Textile Cover)  (except S/N 399)
AFT Left Float Assy  3G9560V01432  303561A  Up to S/N 493 included
(Rigid Cover)  (except S/N 492)
AFT Right Float Assy  3G9560V01532  303562A  Up to S/N 471 included
(Rigid Cover)  (except S/N 469)
Table 1 - Emergency Flotation System equipped with SMA Inflation System P/N 302444A
The Inflation System of Float Assemblies indicated above are NOT affected by this Service Bulletin
only in case the Service Bulletin is already marked:
- On the Float Assembly Log Card;
- On the body of the SMA Actuation Device (Pin-Puller) P/N P-H20006 (Figure 1).
NOTE:  In case an affected Inflation System is replaced with an another one already compliant
with this Service Bulletin, the "SB-139-25-002" has to be recorded on the Float
Assembly Log Card, together with the Inflation System P/N and S/N. Replacement of
the Inflation System with an another one not compliant with this Service Bulletin is not
allowed.
NOTE:  stands for Leonardo S.p.A. Helicopters (formerly Finmeccanica S.p.A.,
AgustaWestland S.p.A.).
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 1 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.9282849
Email: publications@sekur.aero
S.B. N°139-533 ALERT
DATE: August 30, 2018
Page 12 of 22  REVISION: /

### Page 13 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
SMA INFLATION VALVE ASSEMBLY
P/N 302445A
PIN-PULLER P/N P-H20006
SCREW MS24677-2
(хЗ)
SMA INFLATION
IDENTIFICATION  SYSTEM
STICKY LABEL  P/N 302444A
P/N 303726A
CYLINDER P/N P-F20006
Figure 1 - SMA Inflation System P/N 302444A
C. CONCURRENT REQUIREMENTS
N/A.
D. REASON
This service bulletin is being issued to apply an improved reset procedure on SMA Actuation Device
in order to prevent inadvertent floats deployment.
E. DESCRIPTION
Aero Sekur has investigated three events of inadvertent floats deployment on AW139 installations.
The investigation was focused to the SMA Actuation Device (hereinafter Pin-Puller) P/N P-H20006
having the aim to break the frangible pin of the inflation valve, allowing the gas releasing from the
cylinder to the Emergency Flotation Systems. In all cases, the Pin-pullers investigated have
presented similar and comparable electrical properties and were not possible to notice any kind of
flaw or out-of-acceptance parameter. However, evaluations conducted on the reset procedure of the
Pin-puller highlighted that, although difficult, an improper reset may occurred, leading to a not stable
condition of the retractable pin of the actuator.
This service bulletin is being issued to apply one-off an improved reset procedure on each Pin-puller
installed on SMA inflation systems listed in paragraph 1.B. The units and spares not listed in
paragraph 1.B incorporate this modification at the time of manufacture and are not affected by this
Service Bulletin.
The procedures in this Service Bulletin require that the units in Table 1 are removed from the
helicopter and moved to the workshop.
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 2 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.9282849
Email: publications@sekur.aero
S.B. N°139-533 ALERT
DATE: August 30, 2018
REVISION: /  Page 13 of 22

### Page 14 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
The accomplishment of this Service Bulletin may be also performed by the personnel entitled to
remove/install the Emergency Flotation Systems from helicopter or by the Trained operators (I level)
or by the Authorized service stations (Il level). A self-training video tutorial to accomplish the
improved reset procedure will be available for download thru "Leonardo AW Customer Portal" for
operators or thru "Aero Sekur web portal" for the authorized service stations; Viewing of the self-
training video is mandatory before execution of this Service Bulletin.
F. COMPLIANCE:
MANDATORY. This service Bulletin shall be accomplished:
- For Equipment (refer to paragraph 1.B) in-service, refer to the helicopter Type Certificate
Holder instructions.
- For Equipment (refer to paragraph 1.B) kept in stock or in the repair loop, prior to the
installation on helicopter.
A Service Bulletin published by Aero Sekur Company may be recorded as "completed" in the
appropriate Log Card only when the following general requirements are satisfied:
1. A mechanic must complete all of the instructions in the Service Bulletin, including the intent
therein.
2. The mechanic must correctly use and install all applicable parts supplied with the Service
Bulletin kit.
3. The mechanic must apply the information in the Service Bulletin only to items part number,
serial number identified in the "Effectivity" section of the Bulletin.
4. The mechanic must use maintenance practices that are identified as acceptable standard
practices in the aviation industry and governmental regulations.
G. APPROVAL:
The content of this document is approved by Leonardo S.p.A. Helicopters (formerly Finmeccanica
S.p.A., AgustaWestland S.p.A.), Design Authority of the AW139 Emergency Flotation System.
H. MANPOWER:
Estimated Labor-Hours to comply with this Service Bulletin:
one (1) hour approx.
NOTE:  This estimate is based on hands-on time and may vary with personnel and facilities
available.
NOTE:  These labor-hours only concern the work described in this Service Bulletin and do not
include other maintenance work which may be performed on this occasion.
NOTE:
Inflation system.
I. WEIGHT AND BALANCE:
N/A.
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 3 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.9282849
Email: publications@sekur.aero
S.B. N°139-533 ALERT
DATE: August 30, 2018
Page 14 of 22  REVISION: /

### Page 15 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
J. REFERENCES:
N/A.
K. PUBLICATION AFFECTED:
Component Maintenance Manual (CMM) 25-60-04, Rev. 3, Dated 21 April 2016.
2. MATERIAL INFORMATION
A. MATERIAL
Table 2 lists materials required for compliance with this Service Bulletin.
PART NAME  P/N  SOURCE
Neoprene sheet or  Local Supply  To protect the cylinder surface
equivalent  when immobilized.
Permanent Marker, Edding  Local Supply  Consumable material to mark
400 or equivalent  the compliance with this SB.
Wire-locking  MS20995-C20  Local supply  To lock-wire the screws.
Table 2 - Materials required
B. TOOLING
Table 3 lists tools required for compliance with this Service Bulletin.
PART NAME  P/N  SOURCE  USE
Diffuser Cap  303717A  Aero Sekur  Safety cap for the outlet of the
inflation head valve.
Diffuser Cap  303719A  Aero Sekur  Safety cap for the outlet of the
inflation head valve.
Hexagonal Key, 3/32"  Local supply  Remove the screws that hold
the Pin-puller
Hexagonal Key, 5/32"  Local supply  Remove the screws that hold
the Support
Lock Wire Pliers  Local supply  Apply the lock wire
P50 Reset tool  317946A  Aero Sekur  Manual reset of the pin-puller
Plastic Shorting Plug  MS90376-10R  Local supply  Protect the electrical connector
Soft  Vice Chain or  Local supply  Safely hold the inflation system
equivalent
Torque Wrench, 1.0 to 6.0  Local supply  Tightening of the screws.
Nm
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 4 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.9282849
Email: publications@sekur.aero
S.B. N°139-533 ALERT
DATE: August 30, 2018
REVISION: /  Page 15 of 22

### Page 16 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
PART NAME  P/N  SOURCE  USE
Torque  Wrench  or  Local supply Manual reset of the pin-puller
screwdrivers, 0.3 to 1.5 Nm
Wire cutters  Local supply Remove the wire locking
Table 3 - Tools required
C. INDUSTRY SUPPORT INFORMATION
(1)  Who comply with the instructions of this Bulletin will be eligible to receive one P50 Reset
tool P/N 317946A (ref. to Table 3) on free of charge basis. Additional P50 reset tool may
be ordered to Aero Sekur.
(2) Labor reimbursement is not available for this subject.
3. ACCOMPLISHMENT INFORMATION
CAUTION:  PRIOR TO ACCOMPLISH THIS SERVICE BULLETIN, ENSURE TO HAVE SEEN
AND UNDERSTOOD ALL THE INSTRUCTIONS SHOWED IN
TRAINING VIDEO TUTORIAL. IF DOUBT EXISTS, PLEASE CONTACT AERO
SEKUR TO: PRODUCT-SUPPORT@SEKUR.AERO
CAUTION:  ALL INSTALLATIONS MUST BE HANDLED WITH EXTREME CARE DURING ALL
WORKING PHASES. ANY OCCURRENCE WHICH MAY POTENTIALLY IMPACT
THE EQUIPMENT INTEGRITY MUST BE REPORTED TO THE MAINTENANCE
STAFF.
CAUTION:  DISASSEMBLING OF THE SUB-PARTS SHOULD BE LIMITED TO THOSE PARTS
THAT NEED TO BE INSPECTED OR REPLACED.
NOTE:  Place an identification tag on all components that are re-usable, including the attaching
hardware that has been removed to gain access to the modification area and adequately
protect them until their later re-use.
NOTE:  Instructions below (paragraphs 3.A and 3.B) are the same for both side of installation (Left-
hand and Right-hand).
A. PRELIMINARY INSTRUCTIONS.
(1)  For equipment affected (refer to paragraph 1.B) and kept in stock, remove it from its
packaging storage conditions.
WARNING:  AFTER CABLE DISCONNECTION, INSTALL THE SHORT PLUG ON THE
ELECTRICAL CONNECTOR OF THE PIN-PULLER.
WARNING:  WHENEVER YOU DISCONNECT HOSES FROM THE INFLATION HEAD
VALVE, IMMEDIATELY INSTALL THE DIFFUSER CAPS ON THE VALVE
OUTLETS BECAUSE UNCOMMANDED ACTIVATION OF THE INFLATION
SYSTEM MAY CAUSE HARM.
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 5 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.928284
mail: publications@sekur.aer
S.B. N°139-533 ALERT
DATE: August 30, 2018
Page 16 of 22  REVISION: /

### Page 17 (OCR)

ANNEX A
AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
For equipment affected (refer to paragraph 1.B) and installed on board, remove it from the
helicopter in accordance with the applicable data module of the AW139 Aircraft
Maintenance Publications.
NOTE:  Replacement of the Inflation System with a unit not compliant with this Service
Bulletin is not allowed. In case of replacement of an affected Inflation System,
install an Inflation System already compliant with this Service Bulletin and
record "SB-139-25-002" on the Float Assembly Log Card, together with the
Inflation System P/N and S/N.
(a)  Move the equipment to a workshop and prepare it for maintenance in a free FOD
area.
B. INSPECTION AND MODIFICATION.
WARNING:  MAKE SURE THAT DIFFUSER CAPS ARE INSTALLED ON THE INFLATION
VALVE OUTLETS BEFORE PROCEEDING, REF. TO FIGURE 2.
Immobilize the pressurized Inflation System in a vice, chain link type or equivalent means
to safely hold the equipment, ref. to Figure 3.
NOTE:  It is recommended to wrap the cylinder with neoprene sheet or equivalent
material to protect the cylinder surface against damage in the area where the
chain link apply.
NOTE:  Prior to tightening the vice-chain, place the inflation system in order to have
the pin-puller on sight (with the pressure gauge looking down).
(2) Cut and remove all wires locking installed on the screws that hold the Support and Pin-
puller to the Support.
CAUTION:  TAKE CARE TO REMOVE THE SUPPORT.  THE HOLE ON THE
RETRACTABLE PIN OF THE  PIN-PULLER IS ENGAGED WITH THE
FRANGIBLE PIN, SO LIFT CAREFULLY THE SUPPORT PERPENDICULARLY
TO THE VALVE BODY.
(3)  Remove the Support unscrewing the four Screws MS24678-11 with Flat Washers, ref. to
Figure 4.
(4) Remove the Pin-puller from the Support unscrewing the three Screws MS24677-2, ref. to
Figure 4.
NOTE:  After Pin-puller removal, it is strongly recommended to temporarily re-apply
the Support on the valve head to protect the frangible pin from unwanted
rupture.
(5) Do the reset procedure (ref. also to the video tutorial):
CAUTION:  TAKE CARE THAT THE HEX SHAFT OF THE RESET TOOL IS FREELY
TO ROTATE. IF ANY, LUBRICATE IT WITH SPRAY LUBRICANT WD-40
OR EQUIVALENT.
(a)  Install the Reset Tool P/N 317946A on the Pin-puller, ref. to Figure 5.
1 Rotate the hexagon shaft clockwise to engage the 6-32 thread of the tool with
the output Pin of the Pin-puller. Continue to rotate the hex shaft until you see
the base of the tool in contact with the pin-puller flange and you feel a force
increase in the hex shatt rotation.
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 6 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.9282849
Email: publications@sekur.aero
S.B. N°139-533 ALERT
DATE: August 30, 2018
REVISION: /  Page 17 of 22

### Page 18 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
(b) Align the thin line marked on the swivel cap with the line marked on the reset tool
body, ref. to Figure 5.
CAUTION:  BE CAREFUL TO SET THE CORRECT TIGHTENING TORQUE, NEVER
EXCEED THE MAXIMUM VALUE.
(c) Set the Torque Wrench to 0.7 10.035 Nm [6.2 10.3 in-lbs] and place the torque
wrench to the hexagon shaft of the reset tool.
CAUTION:  TAKE CARE TO AVOID ANY MOVEMENT OF THE TOOL SWIVEL CAP
DURING TORQUE APPLICATION.
(d) Apply the tightening torque, ref. to Figure 6. Rotate slowly the wrench clockwise until
the tightening torque is reached.
NOTE:  For this purpose it is recommended that a "Click type" torque wrench be
used.
(e) After reaching the tightening torque, check the position of the line marked on the
reset tool body, ref. to Figure 6.
CAUTION:  IF RESET PROCEDURE FAILS, NEVER TRY TO INCREASE THE
TIGHTENING  TORQUE VALUE,  THIS  IRREVERSIBLY
COMPROMISE THE PINPULLER MECHANISM.
The line on the reset tool body has rotated clockwise and it is positioned
beyond the thick line marked on the swivel cap; If not, contact Aero Sekur
(product-support@sekur.aero) for disposition instructions or return the unit to
Aero Sekur for inspection.
(f)  Remove the Reset Tool P/N 317946A from the Pin-puller.
1  Rotate the hexagon shaft counter-clockwise to disengage the 6-32 thread of
the tool with the output Pin of the Pin-puller.
(6) Remove the Support temporarily installed at step (4).
CAUTION:  BE SURE THAT THE CONNECTOR OF PINPULLER IS COVERED BY THE
PLUG.
CAUTION:  THE PIN-PULLER MUST BE ORIENTED SO THAT THE HOLE ON THE
RETRACTABLE PIN IS FACING THE SURFACE OF THE VALVE BODY. THE
HOLE SHALL HOST THE FRANGIBLE PIN WHEN THE SUPPORT IS
APPLIED
(7) Install the Pin-puller to the Support screwing the three Screws MS24677-2. Apply a
tightening torque to the screws between 1.5 to 2.5 Nm [13.2 to 22.1 in-lbs].
CAUTION:  BE VERY CAREFUL, DURING THE COUPLING BETWEEN SUPPORT AND
FRANGIBLE PIN. ABRUPT MOVEMENTS MAY CAUSE UNINTENTIONAL
BREAKING OF THE PIN.
(8)  Place the Support with the Pin-puller, on the valve body, centering it with the frangible Pin.
(9)  Fix the Support screwing the four Screws MS24678-11 with four Flat Washers. Apply a
tightening torque to the screws between 3.2 to 3.8 Nm [28.3 to 33.6 in-lbs]
(10)  Apply the wire locking using the double twisted method referring to general practices for
safety wiring NASM33540:
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 7 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.9282849
Email: publications@sekur.aero
S.B. N°139-533 ALERT
DATE: August 30, 2018
Page 18 of 22  REVISION: /

### Page 19 (OCR)

ANNEX A
AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
CAUTION:  PRIOR TO APPLY THE WIRE LOCKING,  BE SURE THAT
TIGHTENING TORQUE HAS BEEN APPLIED TO EACH SCREW.
CAUTION:  INSTALL WIRE SO THAT THE WIRE WILL BE IN TENSION IF THE
PART LOOSENS. TWIST WIRE TOGETHER SO THAT IT IS TIGHT,
BUT DO NOT OVERSTRESS WIRE AS IT MAY BREAK UNDER
LOAD OR VIBRATION.
(a) Lock-wire two by two the four screws that hold the Support.
(b) Lock-wire together the three screws that hold the Pin-puller to the Support.
(11)  Record compliance with this Service Bulletin to the body of the Pin-Puller P/N P-H20006
Use a permanent marker (ret. to paragraph 2.A) to mark the bulletin reference number
(SB-139-25-002) wherever possible on the body.
Re-install the Inflation System on the Emergency Flotation System or re-put it in its
packaging storage conditions as applicable. Refer to the applicable data module of the
AW 139 Aircraft Maintenance Publications or Component Maintenance Manual 95-61-03.
If any, re-install the Emergency Flotation System to the helicopter in accordance with the
applicable data module of the AW139 Aircraft Maintenance Publications; or re-put the
Emergency Flotation System in its storage conditions.
C. RECORD INSTRUCTION
(1) Record compliance with this Service Bulletin in the Float Assembly Log Card.
In case an affected Inflation System is replaced with an another one already
compliant with this Service Bulletin, the "SB-139-25-002" has to be recorded
on the Float Assembly Log Card, together with the Inflation System P/N and
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 8 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.9282849
Email: publications@sekur.aero
S.B. N°139-533 ALERT
DATE: August 30, 2018
REVISION: /  Page 19 of 22

### Page 20 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
SMA INFLATION VALVE  ASSEMBLY P/N 302445A  DIFFUSER CAP  P/N 303717A
PIN-PULLER
P/N P-H20006
DIFFUSER CAP
P/N 303719A
Figure 2 - Diffuser caps installation
- CYLINDER
- NEOPRENE
STRAP
CHAIN VISE-
Figure 3 - Cylinder immobilized in chain vice tool
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 9 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.9282849
Email: publications@sekur.aero
S.B. N°139-533 ALERT
DATE: August 30, 2018
Page 20 of 22  REVISION: /

### Page 21 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
SCREW
MS24678-11
(x4)
WASHER (x4)
SUPPORT
PIN-PULLER  FRANGIBLE
PIN
SCREW
MS24677-2
(x3)
Figure 4 - Support and Pin-puller removal
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 10 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.9282849
Email: publications@sekur.aero
S.B. N°139-533 ALERT
DATE: August 30, 2018
REVISION: /  Page 21 of 22

### Page 22 (OCR)

ANNEX A
• AERO SEKUR  SERVICE BULLETIN
SB-139-25-002 - Revision No.1
Figure 5 - Reset Tool application and thin line marks alignment
CORRECT RESET:  INCORRECT RESET:
The thin line on the reset tool body has rotate  The thin line on the reset tool body has rotate
clockwise and it is positioned beyond the thick line  clockwise and it is positioned within the thick line
marked on the swivel cap.  marked on the swivel cap.
Figure 6 - Result of reset procedure
Original Issue - 28 May 2018  SB-139-25-002
Revision No. 1 - 28 June 2018  Page 11 of 11
AERO SEKUR SpA, Customer Support, via delle Valli, 04011, Aprilia(LT), ITALY, +39.06.97634000, Fax +39.06.9282849
Email: publications@sekur.aero
S.B. N°139-533 ALERT
DATE: August 30, 2018
Page 22 of 22  REVISION: /

### Page 23

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
