# Leonardo Alert Service Bulletin 139-569: Revision A

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-0507, the docket of AD 2021-18-11. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 139-569](https://openairdocs.org/service-documents/leonardo/sb-139-569.md)
- Title as filed: Leonardo Helicopters ASB No. 139-569 Rev A
- Pages: 14
- PDF: https://openairdocs.org/files/sha256/df/2c/df2cb1dd9b9262fe721d1a1647fbba39a171ffba4e67c94a0a389703e73cde24
- Page: https://openairdocs.org/service-documents/leonardo/sb-139-569/file/df2cb1dd9b92

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N°  139-569 
DA TE:  December 28, 2018 
REV. :  A - February 27, 2019 
Pa ge 1 of 13 
TITLE 
ATA 64 – TAIL ROTOR SLIDER ASSY DETAILED INSPECTION 
REVISION LOG 
The Revision A of this Service Bulletin supersedes the first issue dated December 28, 
2
018. 
Revision A is issued in order to update the accomplishment instructions and the related 
figures. 
Helicopters that have complied with Part II of the first issue of this Service Bulletin do not 
need any additional action.  
Helicopters that have complied with Part I of the first issue of this Service Bulletin and 
• have recorded corrosion, should reconsider the evidences recorded in accordance with
Part I of current Revision A;
• have found only refinishing signs without corrosion, have to keep the next scheduled
inspection as already stated performing the first issue;
• have not recorded corrosion, do not need any additional action.
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S.B. N°139-569 ALERT 
 DATE: December 28, 2018 
Page 2 of 13 REVISION: A - February 27, 2019 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
All AB139/AW139 helicopters. 
B. COMPLIANCE 
PART I 
• Within fifty (50) FH if the slider assy has already logged more than  
twenty-four-hundred (2400) FH at the issue date of this Service Bulletin. 
• Before exceeding twenty-four-hundred-and-fifty (2450) FH if the slider assy has 
NOT logged more than twenty-four-hundred (2400) FH at the issue date of this 
Service Bulletin. 
• Every one (1) year after first accomplishment of Part I, only if during the inspection 
signs of refinishing are found. 
PART II 
Immediately after compliance with Part I, if evidence of corrosion is found during the 
inspection. 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
This Service Bulletin is issued in order to require the inspection of the slider assembly 
on the tail rotor. 
E. DESCRIPTION 
Following a reported occurrence of Tail Rotor Slider found cracked on an AW139 
helicopter after landing, this Service Bulletin requires a detailed inspection of the slider 
assembly P/N 3G6430A00131 for corrosion and mechanical damage and, depending 
on findings, the replacement of the part.  
In particular, the investigation on the cracked slider highlighted presence of corrosion 
craters on its surface, originated along finishing signs compatible with low grit sanding 
operations, possibly generated from a maintenance activity not allowed in service. 
This condition, if not detected and corrected, could lead to the breakage of the slider.

### Page 3

S.B. N°139-569 ALERT 
DATE: December 28, 2018 
REVISION: A - February 27, 2019 Page 3 of 13 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin the following MMH are deemed necessary: 
Part I: approximately one (1) MMH. 
Part II:  
• approximately four (4) MMH, if tool kit P/N 3G6405G04032 is NOT available at 
Customer’s facilities. 
• approximately ten (10) MMH, if tool kit P/N 3G6405G04032 is available at 
Customer’s facilities. 
MMH are based on hands-on time and can change with personnel and facilities 
available. 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE DESCRIPTION PART 
DM01 39-A-00-20-00-00A-120A-A Helicopter on ground for a safe 
maintenance. 
I 
DM02 39-A-64-31-04-00A-520A-A  Sliding control assembly - 
Remove procedure 
I, II 
DM03 39-A-64-31-04-00A-720A-A  Sliding control assembly - Install 
procedure 
I, II

### Page 4

S.B. N°139-569 ALERT 
 DATE: December 28, 2018 
Page 4 of 13 REVISION: A - February 27, 2019 
DATA MODULE DESCRIPTION PART 
DM04 39-A-64-31-04-02A-530A-B Spider and slider assembly 
(sliding control assembly) - 
Disassemble procedure 
I 
DM05 39-A-64-31-04-02A-710A-B  Spider and slider assembly 
(sliding control assembly) - 
Assemble procedure 
I 
DM06 39-A-64-31-04-01A-921A-B Duplex bearing (sliding control 
assembly) - Replacement 
(remove and install a new item) 
I, II 
DM07 CSRP-A-51-21-08-00A-649A-D  Passivation of CRES - Other 
process to change the surface 
finish of material 
I 
2) ACRONYMS 
AMDI Aircraft Material Data Information 
AMP Aircraft Maintenance Publication 
DM Data Module 
DOA Design Organization Approval 
EASA European Aviation Safety Agency 
FH Flight Hours 
ITEP Illustrated Tools and Equipment Publication 
LHD Leonardo Helicopter Division 
MMH Maintenance Man Hours 
MMIR Maintenance Malfunction Information Report 
SB Service Bulletin 
TR Tail Rotor 
WRM Warranty Reply Memo 
3) ANNEX 
N.A. 
J. PUBLICATIONS AFFECTED 
AW139 AMP 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 5

S.B. N°139-569 ALERT 
DATE: December 28, 2018 
REVISION: A - February 27, 2019 Page 5 of 13 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
PART I 
N.A. 
PART II 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
1 3G6430A02531 3G6430A01931 Sliding control assy 1 . (1) - 
2) CONSUMABLES 
The following consumable materials, or equivalent, are necessary to accomplish this 
Service Bulletin: 
# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 
2 Commercial Gloves AR (2) I, II 
3 MS20995C32 Lockwire AR (2) (3) I, II 
4 A629A02UV or AW001CK02UV Strap tiedown AR (2) (3) I, II 
5 CCC-C-440, Class I Cheesecloth (C028) AR (2) I 
6 TT-N-95, Type II Aliphatic naphtha (C059) AR (2) I 
7 Commercial 3M Scotch Brite (C015), abrasive pad with grade 7447 or finer AR (2) I 
8 UU-T-106 Masking tape (C064) AR (2) I 
9 AWPS008T PPG Aerospace Semco® Pasa Jell 101 (C905) AR (2) I 
 
Refer also to AMDI for the consumable materials required to comply with the AMP 
DM referenced in the accomplishment instructions. 
3) LOGISTIC MATRIX 
N.A. 
NOTE 
(1) Spider and slider assy P/N 3G6430A01931 is a valid alternative to sliding control 
assy P/N 3G6430A02531, only if tool kit P/N 3G6405G04032 is already available 
at Customer’s facilities.  
(2) Item to be procured as local supply. 
(3) To be procured if already installed on TR boot.

### Page 6

S.B. N°139-569 ALERT 
 DATE: December 28, 2018 
Page 6 of 13 REVISION: A - February 27, 2019 
B. SPECIAL TOOLS 
The following special tools, or equivalent, are necessary to accomplish this Service 
Bulletin: 
# P/N DESCRIPTION Q.TY NOTE PART 
10 Commercial Magnifying glass (10 power) 1 (B1) I 
11 Commercial Light source (fluorescent) / Flashlight 1 (B1) I 
12 RMGE-DS-06-2010-RH Deck servicing platform, RH 1 (B1) I, II 
Refer also to ITEP for the special tools required to comply with the AMP DM 
referenced in the accomplishment instructions. 
SPECIAL TOOLS NOTE 
 Item to be procured a local supply. (B1)
C. INDUSTRY SUPPORT INFORMATION 
WARRANTY: Owners/Operators who comply with the instructions of this Service 
Bulletin no later than the applicable date in the “Compliance” section will be eligible to 
receive necessary replacements on free of charge basis, except for Consumable 
Materials and Special Tools. 
NOTE: Customers who fail to comply with the instructions in this Service Bulletin 
before the compliance date are not eligible for the aforementioned special policy. 
Please Issue relevant MMIR form to your Warranty Administration Dpt.  
NOTE: WRM will include RETURN MATERIAL AUTHORIZATION (RMA) number; the 
unit disembarked from the aircraft has to be returned to LHD within thirty (30) calendar 
days after the shipment of the replacement part. In case of missing return within thirty 
(30) calendar days, Customer will be invoiced for the price of the replacement part.

### Page 7

S.B. N°139-569 ALERT 
DATE: December 28, 2018 
REVISION: A - February 27, 2019 Page 7 of 13 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
Place an identification tag on all components that are 
re-usable, including the attaching hardware that has 
been removed to gain access to the modification area 
and adequately protect them until their later re-use. 
PART I 
1. In accordance with AMP DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. Put the Platform (GG-02-00), or an approved alternative, adjacent to the right side of the 
fuselage. 
NOTE 
During the accomplishment of the following steps, the 
removal of the slider assy from the tail rotor is not 
required, unless specified.  
3. With reference to Figure 1, get access to the TR,  remove the installed tiedown strap or 
lockwire and move the boot to expose the area shown in Figure 2 Detail C. 
WARNING 
BEFORE APPLYING STEP 4, KEEP IN MIND THAT 
THE ALIPHATIC NAPHTHA (C059) IS A 
DANGEROUS MATERIAL. BEFORE YOU DO THIS 
PROCEDURE, MAKE SURE THAT YOU KNOW ALL 
THE SAFETY PRECAUTIONS AND FIRST AID 
INSTRUCTIONS FOR THE ALIPHATIC NAPHTHA. 
4. Clean the base of the slider stem with a clean ch eesecloth (C028) and the aliphatic 
naphtha (C059). 
NOTE 
When you examine the slider assy, use the magnifying 
glass (10 power) and, where necessary, the flashlight.

### Page 8

S.B. N°139-569 ALERT 
 DATE: December 28, 2018 
Page 8 of 13 REVISION: A - February 27, 2019 
NOTE 
During the accomplishment of the following steps, in 
case of doubt contact the Product Support Engineering 
(cse.aw139.aw@leonardocompany.com). 
NOTE 
During the accomplishment of the following steps, limit 
the inspection for corrosion only to the area delimited 
within the Figure 2 Detail C. 
NOTE 
Figure 2 and Figure 3 Details A and B show evidence 
of corrosion damage and signs of surface 
imperfections from refinishing with improper abrasives. 
5. With reference to Figures 2 and 3, identify on th e slider stem the area enclosed within 
the Detail C and compare its finishing with the one shown in Details A and B.  
CAUTION 
During polish operation on the area to be examined 
with the Scotch Brite (C015), make sure that you follow 
the subsequent precautions: 
• The Scotch Brite must be used only in the axial 
direction; 
• The Scotch Brite must be used only with your 
hands. 
6. If you find suspected evidences of corrosion sign s as per Figures 2 and 3, perform 
following step 7, otherwise go to step 9. 
7. Check the suspected evidences of corrosion signs as described in the following 
procedure: 
7.1 In accordance with AMP DM 39-A-64-31-04-00A-520A-A, remove the sliding 
control assembly from the helicopter. 
7.2 Polish gently the related area with a very light Scotch Brite (C015). 
7.3 After polishing, examine the slider:  
7.3.1 If the signs of corrosion are confirmed as per Figure 3, go to Part II to 
replace the slider assembly with a serviceable part. 
7.3.2 If, after polishing, the suspected signs of corrosion are no longer 
evident, perform following step 8 to restore the surface finish. 
8. Restore the surface finish of the slider material as described in the following procedure:  
8.1 In accordance with AMP DM 39-A-64-31-04-02A-530A-B, remove the spider from

### Page 9

S.B. N°139-569 ALERT 
DATE: December 28, 2018 
REVISION: A - February 27, 2019 Page 9 of 13 
the slider.  
CAUTION 
Apply the masking tape (C064) around the area where 
the cleaning solution must be applied. 
During passivation activity pay particular attention not 
to let the cleaning solution flow out from the masking 
tape boundaries to the outer surface. 
8.2 In accordance with the repair publication CSRP-A -51-21-08-00A-649A-D, apply 
the Cleaning solution (C905) on the surface of slider assy. 
8.3 In accordance with AMP DM 39-A-64-31-04-02A-710A-B, assemble the spider 
and the slider components. 
8.4 In accordance with AMP DM 39-A-64-31-04-00A-720A-A, reinstall the siliding 
control assembly on the helicopter.  
9. If evidences of corrosion are not found and evidences of refinishing signs are found, 
update the maintenance schedule to plan the next inspection according to paragraph 
“COMPLIANCE” (Part I). 
10. If no corrosion and no refinishing signs are found, no further action is required. 
11. With reference to Figure 1, move the boot in the right position on the slider assy and 
install the tiedown strap or lockwire. 
12. Remove the platform from the right side of the fuselage. 
13. Return the helicopter to flight configuration and record for compliance with Part I of this 
Service Bulletin on the helicopter logbook. 
14. Send the attached compliance form to the following mail box: 
 cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 10

S.B. N°139-569 ALERT 
 DATE: December 28, 2018 
Page 10 of 13 REVISION: A - February 27, 2019 
PART II 
NOTE 
Perform the following step 1, if tool kit  
P/N 3G6405G04032 is NOT available at Customer’s 
facilities. 
1. Send the sliding control assy P/N 3G6430A02531  r emoved performing Part I to LHD. 
NOTE 
Perform the following steps 2 thru 4, only if tool kit  
P/N 3G6405G04032 is available at Customer’s 
facilities. 
2. In accordance with AMP DM 39-A-64-31-04-01A-921A- B, perform the applicable steps 
to remove the duplex bearing from the sliding control assembly and keep it for  
later re-use.  
3. Send the spider and slider assy P/N 3G6430A01931 removed in previous step 2 to LHD. 
NOTE 
A serviceable part is a component that is new (never 
installed on a helicopter); or a component that, before 
installation, has passed the visual inspection (no 
defects detected) in accordance with the instructions of 
Part I of this SB. 
4. In accordance with AMP DM 39-A-64-31-04-01A-921A- B, perform the applicable steps 
to reinstall the duplex bearing on the spider and slider assy. 
5. In accordance with AMP DM 39-A-64-31-04-00A-720A-A install a serviceable sliding 
control assembly on the helicopter. 
6. Return the helicopter to flight configuration and record for compliance with Part II of this 
Service Bulletin on the helicopter logbook. 
7. Send the attached compliance form to the following mail box: 
 cse.aw139.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 11

Figure 1 
S.B. N°139-569 ALERT 
DATE: December 28, 2018 
REVISION: A - February 27, 2019 Page 11 of 13 
 
 
TR□BOOT
A629A02UV TIEDOWN□STRAP (REF)
OR
MS20995C32□LOCKWIRE□(REF)
RESTORE AFTER□INSPECTION
VIEW A
TR□SCISSORS□REMOVAL IS□NOT REQUIRED
TO□PERFORM THE□INSPECTION

### Page 12 (OCR)

* LEONARDO  HELICOPTERS
DETAIL A  (SEE FIGURE 3)
DETAIL C
DETAIL B  (SEE FIGURE 3)
Corroded area of the Slider stem near  the fracture surface.  The corrosion craters tend to originate  along finishing signs compatible with  sanding operations.  It is to be noted the high distribution of  quite circumferential signs and the low  distribution of craters visible on the thin  edge of the fracture surface.
Figure 2
S.B. N°139-569 ALERT
DATE: December 28, 2018
Page 12 of 13  REVISION: A - February 27, 2019

### Page 13

Figure 3 
S.B. N°139-569 ALERT 
DATE: December 28, 2018 
REVISION: A - February 27, 2019 Page 13 of 13

### Page 14

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
