# Leonardo Alert Service Bulletin 169-023: Revision B

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-0378; AD 2021-11-14 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 169-023](https://openairdocs.org/service-documents/leonardo/sb-169-023.md)
- Title as filed: Leonardo Helicopters ASB 169-023 Rev B (reduced size PDF)
- Pages: 139
- PDF: https://openairdocs.org/files/sha256/d2/65/d2657fccef7e5ffc767298c1c0d35941bc4f328aff2b31e673d1098ce0fb8862
- Page: https://openairdocs.org/service-documents/leonardo/sb-169-023/file/d2657fccef7e

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N° 1 69-023
DAT
E:  May 31, 2017 
REV. : B -April 16, 2018 
Pag e 1 of 138 
TITLE 
ATA 32 - RETRACTABLE LANDING GEAR SYSTEM UPGRADE. 
REVISION LOG 
Revision B is issued to: 
- 
Update the compliance of Part VII in order to match the information reported in AMPI 
tasks 32-37 and 32-38, for plunger inspection and lubrication. 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 2 of 138 REVISION: B - April 16, 2018 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
Part I: AW169 helicopters S/N 69011 and S/N 69017. 
Part II: AW169 helicopters S/N 69007, S/N 69015, S/N 69018 and S/N 69022. 
Part III: AW169 helicopters S/N 69032, S/N 69041 and S/N 69051. 
Part IV: AW169 helicopters S/N 69007, S/N 69009, S/N 69011, S/N 69013, 
S/N 69014, S/N 69015, S/N 69017, S/N 69018, S/N 69020, S/N 69021, 
S/N 69022, S/N 69023, S/N 69024, S/N 69027, S/N 69032, S/N 69041 and 
S/N 69051. 
Part V: AW169 helicopters S/N 69007, S/N 69009, S/N 69011, S/N 69013, 
S/N 69014, S/N 69015, S/N 69017, S/N 69018, S/N 69020, S/N 69021, 
S/N 69022, S/N 69023, S/N 69024, S/N 69025, S/N 69027, S/N 69028, 
S/N 69031, S/N 69032, S/N 69041, S/N 69042, S/N 69043, S/N 69044 and 
S/N 69051. 
Part VI: AW169 helicopters S/N 69009, S/N 69013, S/N 69014, S/N 69020, 
S/N 69021, S/N 69023, S/N 69024, S/N 69025, S/N 69027, S/N 69028, 
S/N 69031, S/N 69042 S/N 69043, S/N 69044 and S/N 69049. 
Part VII:All AW169 helicopters equipped with retractable Landing Gear system 
P/N 6F3200F00311 or P/N 6F3200F00411. 
B. COMPLIANCE 
Part I: within six (6) months since receipt of the initial issue (Rev. /) of this Service 
Bulletin; 
Part II: within six (6) months since receipt of the initial issue (Rev. /) of this Service 
Bulletin; 
Part III: within six (6) months since receipt of the initial issue (Rev. /) of this Service 
Bulletin; 
NOTE 
Refer to the following compliance for Part IV if the 
helicopter is already compliant with BT 169-018 or if it’s 
already equipped with NLG Retracting actuator 
P/N 6F3230V00532 and MLG Retracting actuators 
P/N 6F3230V00832 and P/N 6F3230V01032. 
Part IV: within two hundred (200) FH or six (6) month s since receipt of the initial issue 
(Rev. /) of this Service Bulletin, whichever occurs first, and during the same 
maintenance downtime of Part V;

### Page 3

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 3 of 138 
NOTE 
Refer to the following compliance for Part IV if the 
helicopter is NOT already compliant with BT 169-018 
or if it’s NOT already equipped with NLG Retracting 
actuator P/N 6F3230V00532 and MLG Retracting 
actuators P/N 6F3230V00832 and P/N 6F3230V01032. 
Part IV: during the same maintenance downtime of the applicable Part I, Part II or 
Part III; 
NOTE 
Refer to the following compliance for Part V if the 
helicopter is already compliant with BT 169-018 or if it’s 
already equipped with NLG Retracting actuator 
P/N 6F3230V00532 and MLG Retracting actuators 
P/N 6F3230V00832 and P/N 6F3230V01032 
Part V: within two hundred (200) FH or six (6) months since receipt of the initial issue 
(Rev. /) of this Service Bulletin, whichever occurs first, and during the same 
maintenance downtime of Part IV; 
NOTE 
Refer to the following compliance for Part V if the 
helicopter is NOT already compliant with BT 169-018 
or if it’s NOT already equipped with NLG Retracting 
actuator P/N 6F3230V00532 and MLG Retracting 
actuators P/N 6F3230V00832 and P/N 6F3230V01032 
Part V: during the same maintenance downtime of the a pplicable Part I, Part II or 
Part III; 
Part VI: within two hundred (200) FH or six (6) months since receipt of the initial issue 
(Rev. /) of this Service Bulletin, whichever occurs first. 
Part VI shall be performed before Part IV and/or Part V (if applicable), and 
during the same maintenance downtime;

### Page 4

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 4 of 138 REVISION: B - April 16, 2018 
NOTE 
All helicopters affected by Part VI or all helicopters 
already operating the retraction of Landing Gear 
system, shall refer to the following compliance for Part 
VII. 
Part VII: within thirty (30) days or fifty (50) FH si nce receipt of the initial issue (Rev. /) of 
this Service Bulletin, whichever occurs first, and then every thirty (30) days or 
fifty (50) FH, whichever occurs first. 
NOTE 
All helicopters not affected by Part VI nor already 
operating the retraction of Landing Gear system shall 
refer to the following compliance for Part VII. 
Part VII:during the same maintenance downtime of the applicable Part I, Part II or 
Part III, and then every thirty (30) days or fifty (50) FH, whichever occurs first. 
C. CONCURRENT REQUIREMENTS 
This Service Bulletin cancels and supersedes the BT 169-018 Rev. /. 
D. REASON 
This Service Bulletin is issued in order to provide all necessary instructions on how to 
p
erform the retro-modification of the retractable landing gear system and provides 
instructions on how to perform the replacement of the existing control box with the 
latest one by means of the retromod P/N 6F3200P01211 and to install the improved 
landing gear proximity switch by means of the retromod P/N 6F3200P00211. 
E. DESCRIPTION 
Leonardo Helicopters has developed the present Service bulletin in order to provide all 
n
ecessary instructions to enable the fully functionality of the landing gear system. 
In detail: 
Part I provides instructions on how to replace the existing Landing Gear actuators with 
the enhanced version, removing the temporary inhibition of the landing gear retraction 
introduced by means of the BT 169-005 Rev.A. 
Part II provides instructions on how to install the enhanced landing gear retracting 
actuators, removing the temporary mechanical locking of landing gear, provided with 
retromodification P/N 6F3200P00411.

### Page 5

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 5 of 138 
Part III provides instructions on how to install the enhanced landing gear retracting 
actuators on all helicopters already equipped with part of the structural provision of the 
new Nose Landing Gear (NLG) installation. 
The enhanced NLG retracting actuator P/N 6F3230V00532 and MLG retracting 
actuators P/N 6F3230V00832 and P/N 6F3230V01032, introduce improvements on 
the following items: 
 output shaft screws: these changes are aimed to improve the torque 
transmission and the axial support to the bearing; 
 support bearing: this change is aimed to react the load both in radial and axial 
direction, thus preventing jamming of the harmonic drive; 
 internal modification : these changes are aimed to improve the clearance of 
internal sensing components; 
 double lever: this change is added to the reaction rod to attenuate the torque 
perpendicular to the actuator axis. 
Part IV provides all the necessary instructions on how to perform the control box 
modification P/N 6F3200P01211, which allows the replacement of the existing LG 
control box with the new improved one P/N 6F3230V01233. If LG control box 
P/N 6F3230V01231 is installed, the removal of the existing retromod 
P/N 6F3200P00111 is required. 
The improved LG control box P/N 6F3230V01233 has the following improvements: 
 added “idle states” in the logic in order to minimize the effect of unwanted 
multiple state switch; 
 added filtering circuit in order to avoid unwanted multiple state switch; 
 added timeout function in order to protect the actuators; 
 modified load alleviation angle. 
Part V provides all the necessary instructions on how to perform the switch improved 
landing gear retromod P/N 6F3200P00211. 
The switch improved landing gear retromod P/N 6F3200P00211 avoids inadvertent 
current shut off during extension/retraction and incomplete sequences with no current 
shut off which may damage the retracting actuator (RA). 
In detail: 
 installation of proximity switch in lieu of the current rotational one: the rotational 
stiffness of the current switch contrasts lock actuator plunger during extension. 
Marginal set up determines wrong indication to the landing gear control module 
(LGCM) and prevents current shut off to the RA;

### Page 6

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 6 of 138 REVISION: B - April 16, 2018 
 upper linear switch are used as input for LGCM (during retraction it determines 
RA current shut off) and proximity switch are for indication only (connected to 
the landing gear control panel only); 
 Introduction of a mechanical stop preventing the switch failure. 
Part VI provides all the necessary instructions on how to perform installation checks on 
all helicopters already equipped with the new actuators. 
Part VII provides all the necessary instructions on how to perform an inspection on the 
Up Down Lock Actuator plunger, in order to check the absence of corrosion spots. 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
n
r. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
G. MANPOWER 
To comply with this Service bulletin the following Maintenance-Man-Hours (MMH) are 
d
eemed necessary:  
Part I: approximately thirty (30) MMH; 
Part II: approximately twenty eight (28) MMH; 
Part III: approximately twenty (20) MMH; 
Part IV: approximately sixteen (16) MMH; 
Part V: approximately one hundred (100) MMH; 
Part VI: approximately eight (8) MMH; 
Part VII:approximately one (1) MMH; 
Maintenance-Man-Hours are based on hands-on time and can change with personnel 
and facilities available. 
H. WEIGHT AND BALANCE 
NOTE 
In order to determine the correct value to be listed in 
Chart A, a configuration check procedure is given, as 
described below. 
PART I 
1. If the helicopter is already equipped with Kit Retractable Landing Gear system 
P/N 6F3200F00411, update the Chart A as described in the following procedure,

### Page 7

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 7 of 138 
otherwise skip to step 2: 
1.1 The following existing entry in Chart A must be deleted: 
P/N 6F3200F00411“Kit Retractable Landing Gear system” 
WEIGHT (Kg) 178.17 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 5026.3 895530.84 
LATERAL BALANCE -8.1 -1443.17 
1.2 The following entry in Chart A must be added: 
P/N 6F3200F00411 + P/N 6F3200P00311  
“Kit Retractable Landing Gear system + Enhanced retraction retromod” 
WEIGHT (Kg) 179.75 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 5000.8 898888.79 
LATERAL BALANCE -7.4 -1330.14 
2. If the helicopter is already equipped with Kit Retractable Landing Gear system 
P/N 6F3200F00311, update the Chart A as described in the following procedure: 
2.1 The following existing entry in Chart A must be deleted: 
P/N 6F3200F00311 
“Kit Retractable Landing Gear system” 
WEIGHT (Kg) 177.734 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 5033.3 894588.54 
LATERAL BALANCE -8.1 -1439.64 
2.2 The following entry in Chart A must be added: 
P/N 6F3200F00311 + P/N 6F3200P00311 
“Kit Retractable Landing Gear system + Enhanced retraction retromod” 
WEIGHT (Kg) 179,31 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 5007.6 897932.78 
LATERAL BALANCE -7.5 -1344.85 
PART II 
1. If the helicopter is already equipped with Kit Retractable Landing Gear system 
P/N 6F3200F00411, update the Chart A as described in the following procedure, 
otherwise skip to step 2:

### Page 8

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 8 of 138 REVISION: B - April 16, 2018 
1.1 The following existing entry in Chart A must be deleted: 
P/N 6F3200F00411 + P/N 6F3200P00411  
“Kit Retractable Landing Gear system + LGS, from retract to fixed retromod” 
WEIGHT (Kg) 154.66 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 5024.1 777027.30 
LATERAL BALANCE -11.1 -1716.71 
1.2 The following entry in Chart A must be added: 
P/N 6F3200F00411 + P/N 6F3200P00411 +P/N 6F3200P00711 
“Kit Retractable Landing Gear system + Enhanced retraction retromod” 
WEIGHT (Kg) 180.85 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 4982.5 901070.18 
LATERAL BALANCE -7.5 1356.35 
2. If the helicopter is already equipped with Kit Retractable Landing Gear system 
P/N 6F3200F00311, update the Chart A as described in the following procedure: 
2.1 The following existing entry in Chart A must be deleted: 
P/N 6F3200F00311 + P/N 6F3200P00411 
“Kit Retractable Landing Gear system + LGS, from retract to fixed retromod” 
WEIGHT (Kg) 154.23 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 5032.2 776086.01 
LATERAL BALANCE -11.1 -1711.89 
2.2 The following entry in Chart A must be added: 
P/N 6F3200F00311 + P/N 6F3200P00411 + P/N 6F3200P00711 
“Kit Retractable Landing Gear system + Enhanced retraction retromod” 
WEIGHT (Kg) 180.41 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 4989.3 900129.59 
LATERAL BALANCE -7.5 -1353.09 
PART III 
1. If the helicopter is already equipped with Kit Retractable Landing Gear system 
P/N 6F3200F00411, update the Chart A as described in the following procedure,

### Page 9

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 9 of 138 
otherwise skip to step 2: 
1.1 The following existing entry in Chart A must be deleted: 
P/N 6F3200F00411 + P/N 6F3200P00411  
“Kit Retractable Landing Gear system + LGS, from retract to fixed retromod” 
WEIGHT (Kg) 154.66 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 5024.1 777027.30 
LATERAL BALANCE -11.1 -1716.71 
1.2 The following entry in Chart A must be added: 
P/N 6F3200F00411 + P/N 6F3200P00411 +P/N 6F3200P711 
“Kit Retractable Landing Gear system + Enhanced retraction retromod” 
WEIGHT (Kg) 179.63 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 5002.0 898534.27 
LATERAL BALANCE -7.8 -1401.15 
2. If the helicopter is already equipped with Kit Retractable Landing Gear system 
P/N 6F3200F00311, update the Chart A as described in the following procedure: 
2.1 The following existing entry in Chart A must be deleted: 
P/N 6F3200F00311 + P/N 6F3200P00411 
“Kit Retractable Landing Gear system + LGS, from retract to fixed retromod” 
WEIGHT (Kg) 154.23 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 5032.2 776086.01 
LATERAL BALANCE -11.1 -1711.89 
2.2 The following entry in Chart A must be added: 
P/N 6F3200F00311 + P/N 6F3200P00411 + P/N 6F3200P00711 
“Kit Retractable Landing Gear system + Enhanced retraction retromod” 
W
EIGHT (Kg) 179.2 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 5008.9 897594.88 
LATERAL BALANCE -7.8 -1397.76

### Page 10

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 10 of 138 REVISION: B - April 16, 2018 
PART IV 
N.A. 
PART V 
N.A. 
PART VI 
N.A. 
PART VII 
N.A. 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE DESCRIPTION PART 
DM01 69-A-00-20-00-00A-120A-A Helicopter on ground for a safe 
maintenance. 
I,II,III,IV,V 
DM02 69-A-06-40-00-00A-010A-A Access provisions - General data I,II,III 
DM03 69-A-07-11-00-00A-100A-A Helicopter - Lift on jacks - 
Operation 
I,II,III 
DM04 69-A-46-26-02-00A-520A-A Number 2 enhanced display 
control unit (EDCU2) - Remove 
procedure 
I,II 
DM05 69-A-53-17-03-00A-520A-A Lower down panel - Remove 
procedure 
I,II 
DM06 69-A-46-26-02-00A-720A-A Number 2 enhanced display 
control unit (EDCU2) - Install 
procedure 
I,II 
DM07 69-A-53-17-03-00A-720A-A Lower down panel - Install 
procedure 
I,II 
DM08 69-A-32-31-02-010-941A-A MLG RETRACTING ACTUATOR 
INSTALLATION - Illustrated Parts 
Data 
II,III 
DM09 69-A-32-63-01-00A-271A-A Nose landing gear micro switch - 
Adjust 
II,III 
DM10 69-A-32-31-00-00A-320A-A Extension and retraction system - 
Emergency extension circuit - 
Operation test 
II,III 
DM11 69-A-32-31-00-01A-320A-A Extension and retraction system - 
Emergency extension circuit - 
Operation test 
II,III

### Page 11

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 11 of 138 
DATA MODULE DESCRIPTION PART 
DM12 69-A-32-31-02-00A-520A-A Landing gear control box - 
Remove procedure 
IV 
DM13 69-A-32-31-02-00A-720A-A Landing gear control box – 
Install  procedure 
IV 
DM14 69-A-32-21-01-00A-520B-A Nose landing gear, retractable - 
Remove procedure 
I 
DM15 69-A-32-21-01-00A-720B-A Nose landing gear, retractable - 
Install procedure 
I 
DM16 69-A-32-31-03-00A-520A-A Nose landing gear actuator - 
Remove procedure 
I 
DM17 69-A-32-31-05-00A-520A-A Left main landing gear actuator - 
Remove procedure 
I 
DM18 69-A-32-31-06-00A-520A-A Right main landing gear actuator -  
Remove procedure 
I 
DM19 69-A-53-15-09-00A-720A-A Double end arm - Install 
procedure 
I, VI 
DM20 69-A-53-15-10-00A-720A-A Double pin arm - Install procedure  I, VI 
DM21 69-A-32-21-01-00A-520A-A Nose landing gear - Remove 
procedure 
II, III 
DM22 69-A-32-31-12-00A-720A-A MLG Actuator Pin, LH - Install 
procedure 
II, III 
DM23 69-A-32-31-13-00A-720A-A MLG Actuator Pin, RH - Install 
procedure 
II, III 
DM24 69-A-32-31-01-00A-520A-A Landing gear control panel - 
Remove procedure 
IV, V 
DM25 69-A-32-31-01-00A-720A-A Landing gear control panel - 
Install procedure 
IV, V 
DM26 69-A-95-63-03-00A-520A-A Left container assy - Remove 
procedure 
IV, V 
DM27 69-A-95-63-03-00A-720A-A Left container assy - Install 
procedure 
IV, V 
DM28 69-A-95-63-04-00A-520A-A Right container assy - Remove 
procedure 
V 
DM29 69-A-95-63-04-00A-720A-A Right container assy - Install 
procedure 
V 
DM30 69-A-32-31-00-00A-320A-A Extension and retraction system - 
Emergency extension circuit - 
Operation test 
I, II, III 
DM31 69-A-32-11-01-00A-520B-A Left main landing gear, 
retractable - Remove procedure 
I, II, III 
DM32 69-A-32-11-01-00A-720B-A Left main landing gear, 
retractable - Install procedure 
I, II, III

### Page 12

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 12 of 138 REVISION: B - April 16, 2018 
DATA MODULE DESCRIPTION PART 
DM33 69-A-32-12-01-00A-520B-A Right main landing gear, 
retractable - Remove procedure 
I, II, III 
DM34 69-A-32-12-01-00A-720B-A Right main landing gear, 
retractable - Install procedure 
I, II, III 
DM35 69-A-53-15-05-00A-520A-A Rod assy (retractable) - Remove 
procedure 
VI 
DM36 69-A-53-15-05-00A-720A-A Rod assy (retractable) - Install 
procedure 
VI 
DM37 69-A-53-15-09-00A-520A-A Double end arm - Remove 
procedure 
VI 
DM38 69-A-53-15-10-00A-520A-A Double pin arm - Remove 
procedure 
VI 
DM39 69-A-12-20-07-00A-240A-A LH/RH MLG pintle pin – 
Lubrication 
VI 
DM40 69-A-53-15-06-00A-720A-A NLG lock support assy - Install 
procedure 
V 
2) ACRONYMS 
AMDI Aircraft Material Data Information 
A
MP Aircraft Maintenance Publication 
ASRP Aircraft Structural Repair Publication 
DM Data Module 
EDCU Enhanced Display and Control Unit 
IPD Illustrated Parts Data 
LG Landing Gear 
LH Left 
MLG Main Landing Gear 
MMH Maintenance-Man-Hours 
NLG Nose Landing Gear 
PFD Primary Flight Display 
RFM Rotorcraft Flight Manual 
RA Retracting Actuator 
RH Right 
WOW Weight-On-Wheel 
SB Service Bulletin

### Page 13

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 13 of 138 
3) ANNEX 
Annex A Retractable landing gear electrical system functional test 
A
nnex B Landing gear retraction system regulation 
J. PUBLICATIONS AFFECTED 
AW169 Aircraft Maintenance Publication (AMP) 
A
W169 Aircraft Structural Repair Publication (ASRP) 
AW169 Illustrated parts data publication (IPD) 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
Modification of option file is not required.

### Page 14

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 14 of 138 REVISION: B - April 16, 2018 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
PART I 
P/N DESCRIPTION Q.TY NOTE 
6F3200P00311 RETRACTING ACTUATOR 
RETROMOD 
REF  
 Composed of:    
6F3230V00532 NLG retracting actuator .1  
6F3230V00832 MLG retracting actuator LH .1  
6F3230V01032 MLG retracting actuator RH .1  
6F5331A42331 Support assy .1  
6F5331A42451 Double arm pin .1  
6F5331A42452 Double arm pin .1 (20) 
6F5331A42551 Double arm end .1  
6F5331A42552 Double arm end .1 (20) 
6F5331A42851 Doubler support .1  
6F5331A42951 Peeling shim .3  
6F5331A43051 Peeling shim .1  
6F5331A43151 Peeling shim .1  
6F5331A44551 NLG lock support buffer (5.5 mm) .1 (20) 
6F5331A44651 NLG lock support buffer (5.0 mm) .1 (20) 
6F5331A44751 NLG lock support buffer (4.5 mm) .1 (20) 
6F5331A44851 NLG lock support buffer (4.0 mm) .1 (20) 
6F5331A44951 Washer .6  
A864A1626E024H Laminated shim .2  
A994A45T024H Washer .1  
G1021-64 Pintlepin .1  
MS20002C6 Washer .1 Local 
Supply 
NAS1149C0632R Washer .1 Local 
Supply 
HL20PB-5-4 Rivet pin .2 Local 
Supply 
HL20PB-5-5 Rivet pin .8 Local 
Supply 
HL20PB-5-6 Rivet pin .4 Local 
Supply

### Page 15

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 15 of 138 
P/N DESCRIPTION Q.TY NOTE 
HL86-5 Collar .14 Local 
Supply(1) 
NAS1720C5L4W Rivet .3 Local 
Supply(2) 
NAS1720C5L5W Rivet .4 Local 
Supply(3) 
NAS1720C5L7W Rivet .3 Local 
Supply (4) 
NAS6606D17 Bolt .1 Local 
Supply 
MS24665-88 Cotter pin .1 Local 
Supply(5) 
MS24665-153 Cotter pin .7 Local 
Supply(6) 
MS24665-300 Cotter pin .5 Local 
Supply(7) 
MS24665-302 Cotter pin .2 Local 
Supply 
G1021-72 Laminated washer 2 (20)(22) 
G1021-73 Laminated washer 2 (20)(23) 
G1019-113 Flange 2  
PART II 
P/N DESCRIPTION Q.TY NOTE 
6F3200P00711 LGS, FROM "TMP FIX" TO 
"RETR ENANCHED" 
RETROMOD 
REF  
 Composed of:    
6F3230V00532 NLG retracting actuator .1  
6F3230V00832 MLG retracting actuator .1  
6F3230V01032 MLG retracting actuator .1  
6F3230V01331 Electrical harness .1  
6F5331A09631 Rod engine assy .1  
6F5331A42331 Support assy .1  
6F5331A42451 Double arm pin .1  
6F5331A42551 Double arm end .1  
6F5331A42851 Doubler support .1  
6F5331A42951 Peeling shim .3  
6F5331A43051 Peeling shim .1  
6F5331A43151 Peeling shim .1  
999-0050-02-223 Bearing sleeve .1

### Page 16

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 16 of 138 REVISION: B - April 16, 2018 
P/N DESCRIPTION Q.TY NOTE 
999-0050-02-267 Bearing sleeve .1  
A864A1626E024H Laminated shim .2  
A994A45T024H Washer .1  
AN3-10 Bolt .1 Local 
Supply (8) 
AN4-10 Bolt .5 Local 
Supply (9) 
G1019-18 Pin .12  
G1019-83 Shim .2  
G1019-84 Flange .1  
G1019-113 Flange .2  
G1019-86 Shim .2  
G1020-84 Flange .1  
G1021-27 Bush .4  
G1021-30 Bolt .2  
G1021-49 Bush .4  
G1021-51 Actuator support .1  
G1021-64 Pintle pin .1  
G1021-74 Fairlead 1  
G1021-75 Fairlead 1  
MS17825-6 Nut .2 Local 
Supply 
MS17826-3 Nut .1 Local 
Supply 
MS17826-4 Nut .5 Local 
Supply 
MS17826-6 Nut .2 Local 
Supply 
MS20002C6 Washer .2 Local 
Supply 
MS21225-6 Nut .2 Local 
Supply 
MS21919WCH8 Clamp 1 Local 
Supply 
(12) 
MS24665-88 Cotter Pin .1 Local 
Supply (5) 
MS24665-153 Cotter pin .7 Local 
Supply (6) 
MS24665-302 Cotter pin .8 Local 
Supply

### Page 17

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 17 of 138 
P/N DESCRIPTION Q.TY NOTE 
NAS1149C0332R Washer .1 Local 
Supply 
NAS1149C0432R Washer .5 Local 
Supply 
NAS1149C0632R Washer .5 Local 
Supply 
HL20PB-5-4 Rivet pin .2 Local 
Supply 
HL20PB-5-5 Rivet pin .8 Local 
Supply 
HL20PB-5-6 Rivet pin .4 Local 
Supply 
HL86-5 Collar .14 Local 
Supply (1) 
NAS1720C5L4W Rivet .3 Local 
Supply(2) 
NAS1720C5L5W Rivet .4 Local 
Supply (3) 
NAS1720C5L7W Rivet .3 Local 
Supply (4) 
NAS1351C3H32 Screw .2 Local 
Supply 
NAS1351C4H32 Screw .10 Local 
Supply 
NAS6606D17 Bolt .1 Local 
Supply 
NAS6606D19 Bolt .1 Local 
Supply 
G1019-44 Pin .2 (10) 
G1019-36 Washer .1 (11) 
MS17826-8 Nut .1 Local 
Supply 
(11) 
MS24665-155 Cotter pin .1 Local 
Supply  
(11) 
A864A0991A018F Laminated washer .2  
G1021-72 Laminated washer .2 (20)(22) 
G1021-73 Laminated washer .2 (20)(23) 
6F5331A42452 Double arm pin .1 (20) 
6F5331A42552 Double arm end .1 (20) 
6F5331A44551 NLG lock support buffer (5.5 mm) .1 (20)

### Page 18

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 18 of 138 REVISION: B - April 16, 2018 
P/N DESCRIPTION Q.TY NOTE 
6F5331A44651 NLG lock support buffer (5.0 mm) .1 (20) 
6F5331A44751 NLG lock support buffer (4.5 mm) .1 (20) 
6F5331A44851 NLG lock support buffer (4.0 mm) .1 (20) 
MS24665-300 Cotter Pin .1  
6F5331A44951 Washer .6  
PART III 
P/N DESCRIPTION Q.TY NOTE 
6F3230V00532 NLG retracting actuator .1  
6F3230V00832 MLG retracting actuator LH .1  
6F3230V01032 MLG retracting actuator RH .1  
6F3230V01331 Electrical harness .1  
6F5331A09631 Rod engine assy .1  
6F5331A42451 Double arm pin .1  
6F5331A42551 Double arm end .1  
999-0050-02-223 Bearing sleeve .1  
999-0050-02-267 Bearing sleeve .1  
A864A1626E024H Laminated shim .2  
A994A45T024H Washer .1  
AN3-10 Bolt .1 Local 
Supply (8) 
AN4-10 Bolt .5 Local 
Supply (9) 
G1019-18 Pin .12  
G1019-83 Shim .2  
G1019-84 Flange .1  
G1019-113 Flange .2  
G1019-86 Shim .2  
G1020-84 Flange .1  
G1021-27 Bush .4  
G1021-30 Bolt .2  
G1021-49 Bush .4  
G1021-51 Actuator support .1  
G1021-64 Pintle pin .1  
G1021-74 Fairlead .1  
G1021-75 Fairlead .1  
MS17825-6 Nut .2 Local 
Supply 
MS17826-3 Nut .1 Local 
Supply

### Page 19

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 19 of 138 
P/N DESCRIPTION Q.TY NOTE 
MS17826-4 Nut .5 Local 
Supply 
MS17826-6 Nut .2 Local 
Supply 
MS20002C6 Washer .2 Local 
Supply 
MS21225-6 Nut .2 Local 
Supply 
MS2191919WCE8 Clamp 1 Local 
Supply 
(12) 
MS24665-88 Cotter pin .1 Local 
Supply(5) 
MS24665-153 Cotter pin .7 Local 
Supply(6) 
MS24665-300 Cotter pin .6 Local 
Supply(7) 
MS24665-302 Cotter pin .2 Local 
Supply 
NAS1149C0332R Washer .1 Local 
Supply 
NAS1149C0432R Washer .5 Local 
Supply 
NAS1149C0632R Washer .5 Local 
Supply 
NAS1351C3H32 Screw .2 Local 
Supply 
NAS1351C4H32 Screw .10 Local 
Supply 
NAS6606D17 Bolt .1 Local 
Supply 
NAS6606D19 Bolt .1 Local 
Supply 
G1019-44 Pin .2 (10) 
G1019-36 Washer .1 (11) 
MS17826-8 Nut .1 Local 
Supply 
(11) 
MS24665-155 Cotter pin .1 Local 
Supply 
(11) 
A864A0991A018F Laminated Washer .2

### Page 20

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 20 of 138 REVISION: B - April 16, 2018 
P/N DESCRIPTION Q.TY NOTE 
G1021-72 Laminated washer .2 (20)(22) 
G1021-73 Laminated washer .2 (20)(23) 
6F5331A42452 Double arm pin .1 (20) 
6F5331A42552 Double arm end .1 (20) 
6F5331A44551 NLG lock support buffer (5.5 mm) .1 (20) 
6F5331A44651 NLG lock support buffer (5.0 mm) .1 (20) 
6F5331A44751 NLG lock support buffer (4.5 mm) .1 (20) 
6F5331A44851 NLG lock support buffer (4.0 mm) .1 (20) 
6F5331A44951 Washer .6  
PART IV 
P/N DESCRIPTION Q.TY NOTE 
6F3200P01211 CONTROL BOX RETROMOD REF  
 Composed of:    
6F3230V01233 Control box .1  
PART V 
P/N DESCRIPTION Q.TY NOTE 
6F3200P00211 SWITCH IMPROVEMENT, 
LANDING GEAR RETROMOD 
REF  
 Composed of:    
6F3220P00131 LEG ASSY MOD, NLG REF  
 Composed of:    
6F3220A00151 Stop, NLG ..1  
NAS517-3-1 Screw ..2 Local 
Supply 
6F3230A01731 Limit switch MLG assy .2  
6F3230A01831 Limit switch NLG assy .1  
6F5280A03654 UP lock support, MLG LH .1  
6F5280A03753 UP lock support, MLG RH .1  
6F5331A36634 UP lock support assy, NLG .1  
6F5331A38054 Protection, up lock support, NLG .1  
84799114 Switch .3  
A161A0432 Washer .1  
A366A3E10C75 Stud .5  
A388A3E16C75 Stud .1  
A388A3E18C75 Stud .1  
A388A5E12C75L Stud .6  
A388A5E16C75L Stud .2

### Page 21

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 21 of 138 
P/N DESCRIPTION Q.TY NOTE 
AW001CB03H Clamp .4  
AW001CB04H Clamp .2  
AW001CB05H Clamp .1  
AW001CB06H Clamp .1  
AW001CB07H Clamp .8  
AW001CB09H Clamp .1  
MS21042L06 Nut .1 Local 
Supply 
MS21043-3 Nut .5 Local 
Supply 
MS24665-172 Pin cotter .4 Local 
Supply 
MS24665-174 Pin cotter .10 Local 
Supply 
MS24693-C28 Screw .1 Local 
Supply 
MS24693-C30 Screw .1 Local 
Supply 
NAS1149CN632R Washer .1 Local 
Supply 
NAS1149D0316J Washer .13 Local 
Supply 
NAS1190E3P6AK  Screw .2 Local 
Supply 
NAS1802-3-5  Screw .8 Local 
Supply 
6F5310A35011 ICS ISOPAT STRUCT PROV REF  
 Composed of:    
A824A03A-A1  Support ..1   
NAS1149D0316J  Washer ..4  Local 
Supply 
NAS1802-3-5  Screw ..4 Local 
Supply 
NAS1836C3-12M Insert ..4  Local 
Supply 
6F3200P01011 LDG ELECTRICAL PROVISION 
VARIANT 
REF  
 Composed of:    
6F9A21A38701 Undercarriage variant C/A 
(A1A387) 
..1 (14) 
6F9A21B41301 Undercarriage variant C/A 
(A1B413) 
..1 (15)

### Page 22

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 22 of 138 REVISION: B - April 16, 2018 
P/N DESCRIPTION Q.TY NOTE 
6F9A22A22901 Undercarriage variant C/A 
(A2A229) 
..1 (16) 
6F9A22B25701 Undercarriage variant C/A 
(A2B257) 
..1 (17) 
A656A01  Relay ..1  
ED300K220  Decal ..1  
6F5331A02352 Shim 1  
6F5331A04351 Shim 1  
6F5331A44551 NLG lock support buffer (5.5 mm) 1 (20)(21) 
6F5331A44651 NLG lock support buffer (5.0 mm) 1 (20)(21) 
6F5331A44751 NLG lock support buffer (4.5 mm) 1 (20)(21) 
6F5331A44851 NLG lock support buffer (4.0 mm) 1 (20)(21) 
M39029/56-348 Electrical Contact 7 Local 
Supply 
M39029/56-351 Electrical Contact 13 Local 
Supply 
M39029/58-360 Electrical Contact 2 Local 
Supply 
M39029/58-363 Electrical Contact 2 Local 
Supply 
MS25036-102 Terminal Lug 2 Local 
Supply 
PART VI 
P/N DESCRIPTION Q.TY NOTE 
MS24665-88 Cotter pin 1 (5) 
MS24665-300 Cotter pin 1 (7) 
G1021-72 Laminated washer 2 (20)(22) 
G1021-73 Laminated washer 2 (20)(23) 
PART VII 
N.A. 
 
The following consumable materials, or equivalent, are necessary to comply 
with this Service Bulletin: 
2) CONSUMABLES 
Spec./AW code number DESCRIPTION Q.TY NOTE PART 
AFS 1646 - DTD5577 
Code No. 900000262 
Adhesive Permabond 
F241 
AR Local 
Supply 
V

### Page 23

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 23 of 138 
Spec./AW code number DESCRIPTION Q.TY NOTE PART 
MS20995C32 Safety wire (C014) 0.45Kg  Local 
Supply 
I,II,III, 
V 
NAS1802-3-21 Screw 1 Local 
Supply 
I,II,III 
NAS43DD3-56N Spacer 1 Local 
Supply 
I,II,III 
199-05-002 Type II, Class 2 / 
Code No. 900004603 
(MMM-A-132) 
Adhesive EA934NA (C054) AR Local 
Supply 
V 
A583A2610W Cap ends 20 (18) 
(19) 
IV, V 
199-05-152 Type 3 
Code No. 900002972 
Rubber adhesive RTV730 
(C125) 
AR Local 
Supply 
I,II,III, 
V 
Commercial 
Code No. 
999999999000012566 
Lubricant fluid WD-40 
(C245) 
AR Local 
Supply 
I, II, III, 
VII 
MS21225-6 Nut 1 Local 
Supply 
II, III 
MS17826-8 Nut 1 Local 
Supply 
II, III 
MS24665-155 Cotter Pin 1 Local 
Supply 
II, III 
Commercial Abrasive paper grade 320 
or finer 
AR Local 
Supply 
V 
ASTM D-740 
Code No. 
Solvent (C005) (Methyl-
Ethyl-Ketone) 
AR Local 
Supply 
V 
UU-T-106 
Code No. 
Masking tape (C064) AR Local 
Supply 
V 
Commercial 
Code No. 
999999999000019133 
Lubricant Aeroshell 33 AR Local 
Supply 
I, II, III 
M39029/56-351 Contacts AR Local 
Supply 
V 
NOTE: 
(1) P/N HL86PB5 may be used as a valid alternative; 
(2) P/N NAS1720C5-4W or P/N A297A06TW03 may be used as a valid alternative; 
(3) P/N A297A05TW04 or P/N A297A05TW05 may be used as a valid alternative; 
(4) P/N A297A05TW06 may be used as a valid alternative;

### Page 24

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 24 of 138 REVISION: B - April 16, 2018 
(5) P/N MS24665-90 may be used as a valid alternative; 
(6) P/N MS24665-155 may be used as a valid alternative; 
(7) P/N MS24665-302 may be used as a valid alternative; 
(8) P/N AN3-10A may be used as a valid alternative; 
(9) P/N AN4-10A may be used as a valid alternative; 
(10) This item is necessary only if not already installed; 
(11) This item is necessary only if pins P/N G1019-44 are not already installed; 
(12) P/N AS21919WCH08 may be used as a valid alternative. 
(13) This item is necessary only if pintle pin P/N G1021-71 is not already installed. 
(14) This item will be supplied as production P/N 6F9A21A38701A1R; 
(15) This item will be supplied as production P/N 6F9A21B41301A2R; 
(16) This item will be supplied as production P/N 6F9A22A22901A1R; 
(17) This item will be supplied as production P/N 6F9A22B25701A1R; 
(18) This item is necessary only if the helicopter is equipped with Control Box 
P/N 6F3230V01231; 
(19) Tyco/Raychem P/N TC4001 / TC-CAP-4001 may be used as a valid alternative, 
to be Locally Supplied. 
(20) To be provided only if the check procedures are not passed. 
(21) This item shall not be provided if the helicopter is affected by Part I, Part II or Part 
III of the present Service Bulletin. 
(22) P/N 6F3220A00351 may be supplied as a valid alternative. 
(23) P/N 6F3220A00251 may be supplied as a valid alternative. 
B.  SPECIAL TOOLS 
NOTE 
If the present tools are not already owned in 
Customer’s stock, please contact Leonardo Helicopters 
order administration point of contact to request the 
tools supply on loan. As soon as the present Service 
Bulletin is implemented the tools supplied on loan shall 
be promptly returned to Leonardo Helicopters: 
P/N DESCRIPTION Q.TY NOTE PART 
6F3200H00311A686B Tool kit, L/G micro switch 
setting 
AR  IV, V 
6F3200H00231A023D NLG centering actuator pin 1 (13) I, II,III 
6F3200H00231A023C NLG centering actuator pin 1  I, II, III, 
VI

### Page 25

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 25 of 138 
P/N DESCRIPTION Q.TY NOTE PART 
6F3200H00351A651A Alignment tool 1  I, II, III  
6F3200H00351A651B Alignment tool 1  I, II, III, 
VI 
6F3200H00351A651C Alignment tool 1  I, II, III, 
VI 
C. INDUSTRY SUPPORT INFORMATION 
Owners/Operators who comply with the instructions of this Service Bulletin no later 
t
han the applicable date in the “Compliance” section will be eligible to receive 
REQUIRED MATERIALS on free of charge basis, except for Consumable Materials 
and Special Tools.  
NOTE: Customers who fail to comply with the instructions in this Service Bulletin 
before the compliance date are not eligible for the aforementioned special policy.  
Please Issue relevant MMIR for parts IV and V only to your Warranty Administration 
Dpt.  
MMIR not is not required parts I, II and III – Material will be provided directly from 
Production.  
Please provide through your CSM a formal “Free of Charge” Order to LHD. 
MMIR not is not required parts VI – Material will be provided if needed.  
Please provide through your CSM a formal “Free of Charge” Order to LHD. 
NOTE: WRM will include RETURN MATERIAL AUTHORIZATION (RMA) number; the 
unit disembarked (P/N 6F3230V01231 or 6F3230V01232) from the aircraft has to be 
returned to LHD within thirty (30) calendar days after the shipment of the replacement 
part. In case of missing return within thirty (30) calendar days, Customer will be 
invoiced for the price of the replacement part.

### Page 26

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 26 of 138 REVISION: B - April 16, 2018 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the 
modification area and adequately protect them until 
their later re-use. 
b) Shape the cables in order to prevent interference 
with the structure and the other existing 
installations, using where necessary suitable lacing 
cords. 
c) Exercise extreme care during drilling operations to 
prevent instruments, cables and hoses damage. 
d) After drilling, remove all debris and sharp edges. 
Apply on bare metal a light film of primer unless the 
hole is used for ground connection. 
e) During the installation of bonding braids or 
components requiring grounding, clean the surface 
structure in order to obtain a good ground contact. 
f) Let adhesive cure at room temperature for at least 
24 hours unless otherwise specified. 
g) All lengths are in mm. 
h) Take care to not return the helicopter to flight 
configuration if two or more Parts of this Service 
Bulletin are performed consequently. 
PART I 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. In accordance with AMP DM 69-A-06-40-00-00A-010A-A, remove access panels 191DL 
and 192DR. 
3. In accordance with AMP DM 69-A-07-11-00-00A-100A-A lift the helicopters on jacks. 
4. In accordance with AMP DM 69-A-46-26-02-00A-520A-A and  
DM 69-A-53-17-03-00A-520A-A, temporarily remove the EDCU2 and the access panel 
133AL in order to gain access to the work area.

### Page 27

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 27 of 138 
5. In accordance with AMP DM 69-A-32-31-03-00A-520A-A, remove n°1 actuator support  
P/N G1021-51 and n°1 NLG retracting actuator P/N 6F3230V00531 from the nose 
landing gear assy. Retain all the removed attaching hardware and the actuator support 
P/N G1021-51, for later reuse. 
6. With reference to Figure 30, check the laminated washers P/N G1021-72 and  
P/N G1021-73, as described in the following procedure: 
6.1 With reference to Figure 30, measure the thickness of n°2 laminated washers  
P/N G1021-72. Make sure that the thickness of the two laminated washers is the 
same. 
6.2 With reference to Figure 30, measure the thickness of n°2 laminated washers  
P/N G1021-73. Make sure that the thickness of the two laminated washers is the 
same. 
NOTE 
If the check at the steps 6.1 and 6.2 is not passed, 
proceed with steps 6.3 and 6.4 in order to replace the 
existing washers with new ones. Otherwise skip to 
step 7. 
6.3 In accordance with AMP DM 69-A-32-21-01-00A-520B- A, remove the nose 
landing gear assy from the helicopter. Retain all the removed attaching hardware 
for later reuse. Discard the existing n°2 laminated washers P/N G1021-72 and 
n°2 laminated washers P/N G1021-73. 
6.4 In accordance with AMP DM 69-A-32-21-01-00A-720B-A, install the nose landing 
gear assy in its position on the helicopter structure. Install n°2 new laminated 
washers P/N G1021-72 and n°2 new laminated washers P/N G1021-73. 
7. Perform the check on the NLG lock support buffer as described in the following 
procedure: 
7.1 Measure the gap between NLG and existing NLG lock support buffer 
P/N 6F5331A39251. If gap is 0.10 ÷ 0.40 skip to step 7.3, otherwise perform step 
7.2. 
7.2 With reference to Figure 29 view A, replace the existing buffer with one of the 
followings in order to obtain the correct gap; use rubber adhesive RTV730 (C125) 
then skip to step 7.4: 
• NLG lock support buffer (5.5 mm) P/N 6F5331A44551; 
• NLG lock support buffer (5.0 mm) P/N 6F5331A44651; 
• NLG lock support buffer (4.5 mm) P/N 6F5331A44751; 
• NLG lock support buffer (4.0 mm) P/N 6F5331A44851.

### Page 28

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 28 of 138 REVISION: B - April 16, 2018 
7.3 Perform the replacement of the adhesive fixing the NLG support buffers, as 
described in the following procedure: 
7.3.1 With reference to Figure 29, temporarily remove the existing NLG lock 
support buffer P/N 6F5331A39251. 
7.3.2 Remove the existing adhesive and properly clean the relevant surface. 
NOTE 
When reinstalling the NLG support buffer, make sure 
the gap between NLG and existing NLG lock support 
buffer P/N 6F5331A39251 is 0.10 ÷ 0.40. 
7.3.3 With reference to Figure 29, reinstall the NLG lock support buffer 
P/N 6F5331A39251 by means of rubber adhesive RTV730 (C125). 
7.4 Perform the replacement of the adhesive fixing the MLG support buffers, as 
described in the following procedure: 
7.4.1 With reference to Figure 29, temporarily remove the existing n°2 MLG 
lock support buffers P/N 6F5280A11051. 
7.4.2 Remove the existing adhesive and properly clean the relevant 
surfaces. 
7.4.3 With reference to Figure 29, reinstall the n°2 MLG lock support buffers 
P/N 6F5280A11051 by means of rubber adhesive RTV730 (C125). 
7.4.4 With reference to Figure 29 view B, make sure that the total height of 
the installed NLG lock support buffer and the rubber adhesive RTV730 
(C125) does not exceed 6.3 mm. 
8. In accordance with AMP DM 69-A-32-21-01-00A-520B-A, remove the nose landing gear 
assy from the helicopter. Retain all the removed attaching hardware for later reuse. Put 
the nose landing gear assy on a work bench. 
9. With reference to Figure 1, Figure 2 and Figure 6 thru Figure 11, perform the NLG 
retracting actuator retro-modification P/N 6F3200P00311, as described in the following 
procedure: 
9.1 With reference to Figure 1 view B, remove the existing lockwire from the landing 
gear lever. 
9.2 With reference to Figure 1 view C, remove n°2 decals “LANDING GEAR 
RETRACTION INOPERATIVE” from the two PFDs. 
9.3 In accordance with AMP DM 69-A-32-31-06-00A-520A-A, remove n°1 MLG 
retracting actuator RH P/N 6F3230V01031. Retain all the removed attaching 
hardware for later reuse. 
9.4 In accordance with AMP DM 69-A-32-31-05-00A-520A-A, remove n°1 MLG

### Page 29

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 29 of 138 
retracting actuator LH P/N 6F3230V00831. Retain all the removed attaching 
hardware for later reuse. 
9.5 With reference to Figure 6, remove n°1 screw P/N NAS1802-3-4, n°1 washer 
P/N NAS1149D0316J, n°1 clamp P/N AW001CB05H and n°1 standoff 
P/N A388A5E22C75L. Remove and discard the existing Undercarriage cable 
assy P/N 6F3230A00831 and relevant Up-lock Support Buffer 
P/N 6F5331A38651. 
9.6 With reference to Figure 7 view B and view C, remove n°12 rivets  
P/N MS20470E5. 
CAUTION 
Pay particular attention during the removal of existing 
rivets P/N MS20470E5, to avoid any damage to the 
cable assemblies located under the EDCU2. 
9.7 With reference to Figure 6 view A, Figure 7 detai l D and Figure 8 detail E, remove 
n°4 rivets P/N MS20470E5. 
9.8 With reference to Figure 8 view G and Figure 11 view P, install n°1 NLG 
retracting actuator P/N 6F3230V00532 on the actuator support P/N G1021-51 by 
means of the previously retained n°5 bolts P/N AN4-10, n°1 bolt AN3-10, n°5 
washers P/N NAS1149C0432R, n°1 washers P/N NAS1149C0332R, n°5 nuts 
P/N MS17826-4, n°1 nut P/N MS17826-3 and n°6 new cotter pins  
P/N MS24665-153. Torque the bolts P/N AN4-10 to 4 ÷ 5 Nm (35 ÷ 44 lbfin). 
Torque the bolt P/N AN3-10 to 2.5 ÷ 3.5 Nm (22 ÷ 31 lbfin). 
NOTE 
With reference to Figure 8 view G, make sure the NLG 
actuator is correct oriented before proceeding with the 
installation. 
9.9 With reference to Figure 8 view G and Figure 11 v iew N, install the NLG 
retracting actuator P/N 6F3230V00532, as described in the following procedure: 
9.9.1 With reference to Figure 11 view N, install the previously retained n°4 
bushes P/N G1021-27 on the NLG structure. 
NOTE 
Existing pintle pin P/N G1021-71 is necessary to 
perform a correct alignment of the new NLG actuator 
with the NLG rotational axis. NLG centering actuator 
pin P/N 6F3200H00231A023D may be used as a valid 
alternative.

### Page 30

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 30 of 138 REVISION: B - April 16, 2018 
9.9.2 With reference to Figure 8 view G and Figure 11 view N, install the 
NLG retracting actuator P/N 6F3230V00532 mounted on the support  
P/N G1021-51, on its proper installation position. Use the pintle pin  
P/N G1021-71 as position tool, pulling it all the way in letting it enter 
into the relevant hole in the new NLG actuator. 
9.9.3 With reference to Figure 11 view N, install the previously retained n°4 
bushes P/N G1021-49 on the actuator support P/N G1021-51. 
NOTE 
Rotate the n°4 bushes P/N G1021-27 and n°4 bushes 
P/N G1021-49 leaving the pintle pin  
P/N G1021-71 fixed inside the actuator, until the two 
bolts P/N G1021-30 are correctly installed. 
9.9.4 With reference to Figure 11 view N, install the  previously retained n°2 
bolts P/N G1021-30, n°4 washers P/N NAS1149C0632R, n°2 nuts 
P/N MS17825-6 and n°2 new cotter pins P/N MS24665-300. Torque 
the nuts to 25.0 ÷ 30.0 Nm (221 ÷ 266 lbfin). 
9.10 With reference to Figure 31, remove the pintle pin P/N G1021-71 from the NLG 
retracting actuator P/N 6F3230V00532. 
9.11 With reference to Figure 31, install n°1 NLG centering actuator pin  
P/N 6F3200H00231A023C in its correct position in the NLG retracting actuator 
P/N 6F3230V00532, in order to check the correct alignment between the 
rotational axis of NLG actuator and the NLG. 
NOTE 
If the rotational axis of NLG actuator and the NLG are 
not properly aligned, remove the NLG retracting 
actuator P/N 6F3230V00532 mounted on the support 
P/N G1021-51 from the NLG assy, and repeat step 9.9. 
Otherwise skip to step 9.12 
9.12 With reference to Figure 10 view L, disassemble the removed pintle pin  
P/N G1021-71 removing n°1 cotter pin P/N MS24665-153, n°1 nut  
P/N MS17825-4, n°1 washer P/N NAS1149C0432R, n°1 bolt P/N G1021-48, n°1 
ring nut P/N G1021-62, n°1 laminated washer P/N G1021-72 and n°1 laminated 
washer P/N G1021-73. Replace the pintle pin P/N G1021-71 with the new one  
P/N G1021-64. Reassemble the new pintle pin P/N G1021-64 by means of all the 
attachment hardware previously removed in this step and a new cotter pin  
P/N MS24665-153. Torque the nut to 6.0 ÷ 7.5 Nm (53 ÷ 66 lbfin).

### Page 31

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 31 of 138 
NOTE 
Do not install clamp P/N MS21919WCE6 and all its 
attaching hardware at this step. 
9.13 In accordance with AMP DM 69-A-32-21-01-00A-720B -A, install the nose landing 
gear assy in its position on the helicopter structure. 
9.14 With reference to Figure 6 view A, Figure 7 view B and view C, temporary install 
n°1 support assy P/N 6F5331A42331, n°3 peeling shims P/N 6F5331A42951 and 
n°1 peeling shim P/N 6F5331A43051 in their correct positions in the nose gear 
bay. 
9.15 With reference to Figure 32, install n°1 alignment tool P/N 6F3200H00351A651A 
in its correct position on the support assy P/N 6F5331A42331. 
NOTE 
If the alignment tool P/N 6F3200H00351A651A doesn't 
fit in its proper position, contact 
PSE_AW169.MBX.AW@leonardocompany.com to 
receive dedicated instructions. 
9.16 With reference to Figure 6 view A, Figure 7 view  B and view C and Figure 32, 
adjust the dimensions of the n°3 peeling shims P/N 6F5331A42951 and n°1 
peeling shim P/N 6F5331A43051 while the alignment tool  
P/N 6F3200H00351A651A is fixed in its installation position. 
9.17 With reference to Figure 32, remove n°1 alignment tool  
P/N 6F3200H00351A651A from the support assy P/N 6F5331A42331. 
9.18 In accordance with AMP DM 69-A-32-21-01-00A-520B-A, remove the nose 
landing gear assy from the helicopter. Retain all the removed attaching hardware 
for later reuse. 
NOTE 
The grip length of rivets P/N NAS1720 must be chosen 
during installation in order to get the best fits due to the 
use of peeling shims. 
The grip length reported in part list, procedure and 
figures are typical for this installation. 
9.19 With reference to Figure 6 view A, Figure 7 view  B and view C, install n°1 support 
assy P/N 6F5331A42331, n°1 peeling shim P/N 6F5331A43051 and n°3 peeling 
shims P/N 6F5331A42951 by means of n°4 rivets P/N NAS1720C5L5W, n°3 rivet 
P/N NAS1720C5L7W, n°1 rivet P/N NAS1720C5L4W, n°8 pin rivets  
P/N HL20PB-5-5 and n°8 collars P/N HL86-5.

### Page 32

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 32 of 138 REVISION: B - April 16, 2018 
9.20 With reference to Figure 6 view A, Figure 7 detail D and Figure 8 detail E, 
position the support P/N 6F5331A42851 and adjust the thickness of the peeling 
shim P/N 6F5331A43151 as necessary. 
9.21 With reference to Figure 6 view A, Figure 7 detail D and Figure 8 detail E, install 
n°1 support P/N 6F5331A42851 and n°1 peeling shim P/N 6F5331A43151by 
means of n°2 rivets P/N NAS1720C5L4W, n°2 pin rivets P/N HL20PB-5-4, n°4 
pin rivets P/N HL20PB-5-6 and n°6 collars P/N HL86-5. 
NOTE 
Do not install clamp P/N MS21919WCE6 and all its 
attaching hardware at this step. 
9.22 In accordance with AMP DM 69-A-32-21-01-00A-720B -A, install the nose landing 
gear assy in its position on the helicopter structure. 
9.23 With reference to Figure 10 view L, install n°1 bolt P/N G1021-78, n°1 washer 
P/N NAS1149C0432R, n°1 nut P/N MS17825-4 and n°1 new cotter pin  
P/N MS24665-88. Torque the nut to 6.0 ÷ 7.5 Nm (53 ÷ 66 lbfin). 
9.24 With reference to Figure 10 view L, install n°1 clamp P/N MS21919WCE6, n°1 
bolt P/N AN3H3A and n°2 washers P/N NAS1149C0363R. Torque the bolt to 2.5 
÷ 3.5 Nm (22 ÷ 31 lbfin). 
9.25 With reference to Figure 33, perform the NLG actuator alignment check by 
means of the tool P/N 6F3200H00351A651B, as described in the following 
procedure: 
9.25.1 With reference to Figure 33, put the tool P/N 6F3200H00351A651Bin 
its position on the support assy P/N 6F5331A42331. 
9.25.2 With reference to Figure 33 section B-B, put n°1feeler gauge (2,5mm) 
on one side of the tool as shown. 
9.25.3 With reference to Figure 33 section B-B, check if there’s enough 
clearance to put n°1 more feeler gauge (2,5mm) on the other side of 
the tool. If the clearance is enough, skip to step 9.29, otherwise 
proceed with step 9.25.4. 
9.25.4 With reference to Figure 33 section B-B, remove the previously 
installed n°2 feeler gauges and check the tool 
P/N 6F3200H00351A651B properly fits within its installation position. If 
it fits perform step 9.26, otherwise contact 
PSE_AW169.MBX.AW@leonardocompany.com to receive proper 
instructions. 
9.26 With reference to Figure 33, remove n°1 alignment tool

### Page 33

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 33 of 138 
P/N 6F3200H00351A651B from the support assy P/N 6F5331A42331. 
9.27 With reference to Figure 9 view J, install n°1 double arm pin  
P/N 6F5331A42452 together with n°1 double arm end P/N 6F5331A42552 by 
means of up to n°6 washers P/N 6F5331A44951 distributed on both sides in 
order to ensure the double arm end interfaces with the NLG actuator without 
frictions or lateral loads. 
9.28 Measure the lateral gap on the double arm pin and fix the installation by means 
of n°2 laminated shims P/N A864A1626E024H of a proper thickness and n°1 
cotter pin P/N MS24665-300 Skip to step 9.32. 
9.29 With reference to Figure 33, remove n°1 alignment tool  
P/N 6F3200H00351A651B from the support assy P/N 6F5331A42331. 
9.30 In accordance with AMP DM 69-A-53-15-10-00A-720A-A and with reference to 
Figure 9 view J, install n°1 double arm pin P/N 6F5331A42451, n°2 laminated 
shims P/N A864A1626E024H and n°1 cotter pin P/N MS24665-300. 
9.31 With reference to Figure 9 view J, install n°1 double arm end P/N 6F5331A42551 
in the double arm pin P/N 6F5331A42451. 
9.32 With reference to Figure 34, install n°1 alignment tool P/N 6F3200H00351A651C 
in its correct position on the double arm end, and on the NLG retracting actuator 
P/N 6F3230V00532. 
9.33 With reference to Figure 34, make sure that the lever of the NLG retracting 
actuator P/N 6F3230V00532 and the support assy P/N 6F5331A42331 are 
parallel. If necessary adjust the position of the lever of the NLG retracting 
actuator P/N 6F3230V00532. 
9.34 With reference to Figure 34, remove n°1 alignment tool  
P/N 6F3200H00351A651C from the double arm end, and from the NLG retracting 
actuator P/N 6F3230V00532. 
9.35 In accordance with AMP DM 69-A-53-15-09-00A-720A-A and with reference to 
Figure 9 view J, attach the previously installed double arm end to the NLG 
retracting actuator P/N 6F3230V00532 by means of n°1 bolt P/N NAS6606D17, 
n°1 washer P/N NAS1149C0632R, n°1 washer P/N MS20002C6, n°1 nut  
P/N MS21225-6 and n°1 cotter pin P/N MS24665-300. Torque the nut to 18.1 ÷ 
21.5 Nm (160 ÷ 190 lbfin). 
9.36 With reference to Figure 9 detail H, adjust the length of the rod engine assy 
P/N 6F5331A09631 to avoid any preload during the installation of the bolt 
P/N NAS6606D19. 
9.37 With reference to Figure 9 detail H, reinstall n°1 bolt P/N NAS6606D19, n°1

### Page 34

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 34 of 138 REVISION: B - April 16, 2018 
washer P/N MS20002C6, n°1 washer P/N A994A45T024H, n°1 bearing sleeve  
P/N 999-0050-02-223, n°1 nut P/N MS21225-6 and n°1 cotter pin  
P/N MS24665-300 that attach the rod engine assy P/N 6F5331A09631 to the 
NLG retracting actuator P/N 6F3230V00532. Torque the nut to 10.7 ÷ 12.4 Nm 
(95-110 lbfin). 
9.38 With reference to Figure 4 and Figure 10, perform the installation of the new MLG 
actuator RH side as described in the following procedure: 
9.38.1 In accordance with the applicable step of AMP  
DM 69-A-32-12-01-00A-520B-A, remove n°1 flange P/N G1019-85, n°6 
pins P/N G1019-18, n°1 flange G1020-84 and n°1 shim P/N G1019-83. 
Discard the flange P/N G1019-85. 
9.38.2 In accordance with the applicable step of AMP  
DM 69-A-32-12-01-00A-520B-A, partially extract the RH MLG assy 
from the pintle pin P/N 6F5338A02653 until the forward part of the RH 
MLG assy is disengaged from the pintle pin. 
9.38.3 If the MLG is not equipped with Grease Nipples apply a layer of 
lubricant fluid WD-40 (C245) on the disengaged part of the RH MLG 
assy and on the exposed part of the pintle pin P/N 6F5338A02653, 
otherwise use lubricant Aeroshell 33. 
9.38.4 In accordance with the applicable step of AMP  
DM 69-A-32-12-01-00A-720B-A, put the RH MLG assy in its correct 
position on the pintle pin P/N 6F5338A02653. Reinstall n°1 shim  
P/N G1019-83, n°1 flange G1020-84, n°6 pins P/N G1019-18 and n°1 
new flange P/N G1019-113. 
NOTE 
Perform electrical connection of the connector A330P1 
once the MLG actuator is in its installation position and 
not yet attached. 
9.38.5 With reference to Figure 10 view M, put the ne w MLG retracting 
actuator RH P/N 6F3230V01032 on its installation position and perform 
the electrical connection with the existing connector A330P1. 
9.38.6 With reference to Figure 10 view M, fix the already positioned MLG 
retracting actuator RH P/N 6F3230V01032 on the already installed 
flange P/N G1019-113 by means of n°5 bolts P/N NAS1351C4H32 and 
n°1 bolt P/N NAS1351C3H32. Torque the bolts P/N NAS1351C4H32 to 
4.0 ÷ 5.0 Nm (35 ÷ 44 lbfin) and torque the bolt P/N NAS1351C3H32 to

### Page 35

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 35 of 138 
2.5 ÷ 3.2 Nm (22 ÷ 28 lbfin). Safety the bolts with lockwire 
P/N MS20995C32. 
9.38.7 With reference to Figure 10 view M, fix n°1 MLG retracting actuator RH 
P/N 6F3230V01032 to the pin P/N G1019-44 by means of n°1 peeling 
shim P/N G1019-86, n°1 nut P/N MS17826-6 and n°1 new cotter pin  
P/N MS24665-302. Torque the nut to 0.2 Nm (1.8 lbfin). Adjust the 
thickness of the peeling shim in order to leave a gap of 0.5 ÷ 0.7. 
9.38.8 With reference to Figure 4 view G, restore electrical connection 
between the connectors P332 and J332 under the baggage 
compartment. 
9.39 With reference to Figure 4 and Figure 10, perform the installation of the new MLG 
actuator LH side as described in the following procedure: 
9.39.1 In accordance with the applicable step of AMP  
DM 69-A-32-11-01-00A-520B-A, remove n°1 flange P/N G2019-85, n°6 
pins P/N G1019-18, n°1 flange G1019-84 and n°1 shim P/N G1019-
83.Discard the flange P/N G1019-85. 
9.39.2 In accordance with the applicable step of AMP  
DM 69-A-32-11-01-00A-520B-A, partially extract the LH MLG assy 
from the pintle pin P/N 6F5338A02653 until the forward part of the LH 
MLG assy is disengaged from the pintle pin. 
9.39.3 If the MLG is not equipped with Grease Nipples apply a layer of 
lubricant fluid WD-40 (C245) on the disengaged part of the LH MLG 
assy and on the exposed part of the pintle pin P/N 6F5338A02653, 
otherwise use lubricant Aeroshell 33. 
9.39.4 In accordance with the applicable step of AMP  
DM 69-A-32-11-01-00A-720B-A, put the LH MLG assy in its correct 
position on the pintle pin P/N 6F5338A02653. Install n°1 shim  
P/N G1019-83, n°1 flange G1019-84, n°6 pins P/N G1019-18 and n°1 
new flange P/N G1019-113. 
NOTE 
Perform electrical connection of the connector A341P1 
once the MLG actuator is in its installation position and 
not yet fixed. 
9.39.5 With reference to Figure 10 view M, put the ML G retracting actuator 
P/N 6F3230V00832 on its installation position and perform the 
electrical connection with the existing connector A341P1.

### Page 36

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 36 of 138 REVISION: B - April 16, 2018 
9.39.6 With reference to Figure 10 view M, fix the already positioned MLG 
retracting actuator P/N 6F3230V00832 on the already installed flange 
P/N G1019-113 by means of n°5 bolts P/N NAS1351C4H32 and n°1 
bolt P/N NAS1351C3H32. Torque the bolts P/N NAS1351C4H32 to 4.0 
÷ 5.0 Nm (35 ÷ 44 lbfin) and torque the bolt P/N NAS1351C3H32 to 2.5 
÷ 3.2 Nm (22 ÷ 28 lbfin). Safety the bolts with lockwire 
P/N MS20995C32. 
9.39.7 With reference to Figure 10 view M, fix n°1 MLG retracting actuator  
P/N 6F3230V00832 to the pin P/N G1019-44 by means of n°1 peeling 
shim P/N G1019-86, n°1 nut P/N MS17826-6 and n°1 cotter pin  
P/N MS24665-302. Torque the nut to 0.2 Nm (1.8 lbfin). Adjust the 
thickness of the peeling shim in order to leave a gap of 0.5 ÷ 0.7. 
9.39.8 With reference to Figure 4 view G, restore electrical connection 
between the connectors P333 and J333 under the baggage 
compartment. 
10. In accordance with AMP DM 69-A-46-26-02-00A-720A-A and  
DM 69-A-53-17-03-00A-720A-A, reinstall the previously removed EDCU2 and the 
access panel 133AL. 
11. In accordance with AMP DM 69-A-06-40-00-00A-010A-A, reinstall the access panels 
191DL and 192DR. 
12. In accordance with AMP DM 69-A-07-11-00-00A-100A-A, lower the helicopter on the 
ground. 
13. Update the log card of NLG assy P/N 6F3220V00132, replacing the previous NLG 
actuator P/N 6F3230V00531 with the new one P/N 6F3230V00532. 
14. Update the log card of LHMLG assy P/N 6F3210V00134 replacing the previous LH MLG 
actuator P/N 6F3230V00831 with the new one P/N 6F3230V00832. 
15. Update the log card of RH MLG assy P/N 6F3210V00232 replacing the previous RH 
MLG actuator P/N 6F3230V01031 with the new one P/N 6F3230V01032. 
16. In accordance with Weight and Balance Changes, update the Chart A (see Rotorcraft 
Flight Manual, Part II, Section 6). 
17. Return the helicopter to flight configuration and record for compliance with Part I of this 
Service Bulletin on the helicopter logbook. 
18. Send the attached compliance form to the following box: 
pse_aw169.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo Web Portal 
and compile the “Technical Bulletin Application Communication”

### Page 37

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 37 of 138 
PART II 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. In accordance with AMP DM 69-A-06-40-00-00A-010A-A, remove access panels 
191DL and 192DR. 
3. In accordance with AMP DM 69-A-07-11-00-00A-100A-A lift the helicopters on jacks. 
NOTE 
If installed, remove the two decals “LANDING GEAR 
RETRACTION INOPERATIVE” from the two PFDs. 
4. In accordance with IPD DM 69-A-32-31-02-010-941A-A  and with reference to Figure 
10, check the pin P/N G1019-44 is installed on both RH and LH Main Landing Gears. 
NOTE 
Perform the following step 5 if the pins P/N G1019-44 
are not installed on the helicopter. Otherwise, skip to 
step 6. 
5. In accordance with AMP DM 69-A-32-31-12-00A-720A-A , AMP  
DM 69-A-32-31-13-00A-720A-Aand with reference to Figure 10, install n°2 pins  
P/N G1019-44 on both RH and LH Main Landing Gears, by means of n°2 washers  
P/N G1019-36, n°2 nuts P/N MS17826-8 and n°2 cotter pins P/N MS24665-155. 
6. In accordance with AMP DM 69-A-46-26-02-00A-520A-A and  
DM69-A-53-17-03-00A-520A-A, temporarily remove the EDCU2 and the access panel 
133AL in order to gain access to the work area. 
7. With reference to Figure 30, check the laminated washers P/N G1021-72 and  
P/N G1021-73, as described in the following procedure: 
7.1 With reference to Figure 30, measure the thickness of n°2 laminated washers  
P/N G1021-72. Make sure that the thickness of the two laminated washers is the 
same. 
7.2 With reference to Figure 30, measure the thickness of n°2 laminated washers  
P/N G1021-73. Make sure that the thickness of the two laminated washers is the 
same.

### Page 38

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 38 of 138 REVISION: B - April 16, 2018 
NOTE 
If the check at the steps 7.1 and 7.2 is not passed, 
proceed with steps 7.3 and 7.4 in order to replace the 
existing washers with new ones. Otherwise skip to 
step 8. 
7.3 In accordance with AMP DM 69-A-32-21-01-00A-520B- A, remove the nose 
landing gear assy from the helicopter. Retain all the removed attaching hardware 
for later reuse. Discard the existing n°2 laminated washers P/N G1021-72 and 
n°2 laminated washers P/N G1021-73. 
7.4 In accordance with AMP DM 69-A-32-21-01-00A-720B-A, install the nose landing 
gear assy in its position on the helicopter structure. Install n°2 new laminated 
washers P/N G1021-72 and n°2 new laminated washers P/N G1021-73. 
8. Perform the check on the NLG lock support buffer as described in the following 
procedure: 
8.1 Measure the gap between NLG and existing NLG lock support buffer 
P/N 6F5331A39251. If gap is 0.10 ÷ 0.40 skip to step 8.3, otherwise perform step 
8.2. 
8.2 With reference to Figure 29 view A, replace the existing buffer with one of the 
followings in order to obtain the correct gap; use rubber adhesive RTV730 (C125) 
then skip to step 8.4: 
• NLG lock support buffer (5.5 mm) P/N 6F5331A44551; 
• NLG lock support buffer (5.0 mm) P/N 6F5331A44651; 
• NLG lock support buffer (4.5 mm) P/N 6F5331A44751; 
• NLG lock support buffer (4.0 mm) P/N 6F5331A44851. 
8.3 Perform the replacement of the adhesive fixing the NLG support buffers, as 
described in the following procedure: 
8.3.1 With reference to Figure 29, temporarily remove the existing NLG lock 
support buffer P/N 6F5331A39251. 
8.3.2 Remove the existing adhesive and properly clean the relevant surface. 
NOTE 
When reinstalling the NLG support buffer, make sure 
the gap between NLG and existing NLG lock support 
buffer P/N 6F5331A39251 is 0.10 ÷ 0.40. 
8.3.3 With reference to Figure 29, reinstall the NLG lock support buffer 
P/N 6F5331A39251 by means of rubber adhesive RTV730 (C125). 
8.4 Perform the replacement of the adhesive fixing the MLG support buffers, as

### Page 39

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 39 of 138 
described in the following procedure: 
8.4.1 With reference to Figure 29, temporarily remove the existing n°2 MLG 
lock support buffers P/N 6F5280A11051. 
8.4.2 Remove the existing adhesive and properly clean the relevant 
surfaces. 
8.4.3 With reference to Figure 29, reinstall the n°2 MLG lock support buffers 
P/N 6F5280A11051 by means of rubber adhesive RTV730 (C125). 
9. With reference to Figure 29 view B, make sure that the total height of the installed NLG 
lock support buffer and the rubber adhesive RTV730 (C125) does not exceed 6.3 
mm.With reference to Figure 14, remove and discard the existing Undercarriage cable 
assy P/N 6F3230A00831 and relevant Up-lock Support Buffer P/N 6F5331A38651. 
10. In accordance with AMP DM 69-A-32-21-01-00A-520A-A, remove the nose landing 
gear assy from the helicopter. Retain all the removed attaching hardware for later 
reuse. Put the nose landing gear assy on an applicable work bench. 
11. With reference to Figure 3 thru Figure 11, perform the LGS from "TMP FIX" to "RETR 
ENANCHED" retro-modification P/N 6F3200P00711, as described in the following 
procedure: 
11.1 With reference to Figure 3 view B, temporarily remove n°1 bolt 
P/N NAS6606D24, n°1 washer P/N MS20002C6, n°1 bearing sleeve  
P/N 999-0050-02-267, n°1 laminated shim P/N A864A0991A018F, n°1 spacer 
P/N NAS43DD6-19N, n°1 laminated shim P/N A864A1308A018F, n°1 washer 
P/N NAS1149C0632R, n°1 nut P/N MS21225-6 and n°1 cotter pin  
P/N MS24665-300. Retain attaching hardware for later reuse and discard the 
spacer P/N NAS43DD6-19N and the cotter pin P/N MS24665-300. 
NOTE 
If necessary, adjust the position between the NLG strut 
P/N 6F5331A37951 and the rod engine assy  
P/N 6F5331A09631 with peeling shim, on both side. 
11.2 With reference to Figure 5 view K, install n°1 r od engine assy 
P/N 6F5331A09631 by means of previously removed n°1 bolt P/N NAS6606D24, 
n°1 washer P/N MS20002C6, n°1 laminated shim P/N A864A0991A018F, n°1 
bearing sleeve P/N 999-0050-02-267, n°1 laminated shim  
P/N A864A1308A018F, n°1 washer P/N NAS1149C0632R, n°1 nut  
P/N MS21225-6 and n°1 new cotter pin P/N MS24665-300. Torque the nut to 
10.7 ÷ 12.4 Nm (95 ÷ 110 lbfin). 
11.3 With reference to Figure 3 view C and view D, remove and discard n°1 plug

### Page 40

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 40 of 138 REVISION: B - April 16, 2018 
P/N D38999/33W25N and n°1 plug P/N D38999/33W13R. 
11.4 With reference to Figure 3 view C and view D, if not already installed on the NLG 
strut, install n°1 fairlead P/N G1021-74 and n°1 fairlead P/N G1021-75 as shown. 
11.5 With reference to Figure 3 view C and view D, install n°1 electrical harness  
P/N 6F3230V01331 by means of n°1 clamp P/N MS21919WCH8and all the ty-
raps as shown. 
11.6 With reference to Figure 4, prepare the installation of MLG actuator RH side as 
described in the following procedure: 
11.6.1 With reference to Figure 4 view G, disconnect the connector P332 and 
loosen the relevant clamp and cable assy C2B125 in order to allow the 
removal of the existing plate assy P/N 6F3210A00131. 
11.6.2 With reference to Figure 4 view F, remove and discard n°1 plate assy 
P/N 6F3210A00131 and n°3 fixing bolts P/N AN4CH7A. 
11.6.3 With reference to Figure 4 view F, remove and discard n°1 fixed flange 
P/N G1019-SA700-82, n°1 flange P/N G1019-SA700-81, n°6 pins  
P/N G1019-SA700-18 and n°1 shim P/N G1019-SA700-83. 
11.6.4 In accordance with the applicable step of AMP  
DM 69-A-32-12-01-00A-520B-A, partially extract the RH MLG assy from 
the pintle pin P/N 6F5338A02653 until the forward part of the RH MLG 
assy is disengaged from the pintle pin. 
11.6.5 If the MLG is not equipped with Grease Nipples apply a layer of lubricant 
fluid WD-40 (C245) on the disengaged part of the RH MLG assy and on 
the exposed part of the pintle pin P/N 6F5338A02653, otherwise use 
lubricant Aeroshell 33. 
11.6.6 With reference to Figure 5 view J and in accordance with the applicable 
step of AMP DM 69-A-32-12-01-00A-720B-A, put the RH MLG assy in its 
correct position on the pintle pin P/N 6F5338A02653. Install n°1 shim  
P/N G1019-83, n°1 flange P/N G1020-84, n°6 pins P/N G1019-18 and n°1 
flange P/N G1019-113. Adjust the thickness of the peeling shim 
P/N G1019-83, in order to leave a gap of 0.1 ÷ 0.2 to the MLG. 
11.7 With reference to Figure 4, prepare the installation of MLG actuator LH side as 
described in the following procedure: 
11.7.1 With reference to Figure 4 view G, disconnect the connector P333 and 
loosen the relevant clamp and cable assy C2A120 in order to allow the 
removal of the existing plate assy P/N 6F3210A00131. 
11.7.2 With reference to Figure 4 view F, remove and discard n°1 plate assy 
P/N 6F3210A00131 and n°3 fixing bolts P/N AN4CH7A.

### Page 41

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 41 of 138 
11.7.3 With reference to Figure 4 view F, remove and discard n°1 fixed flange 
P/N G1019-SA700-82, n°1 flange P/N G1019-SA700-81, n°6 pins  
P/N G1019-SA700-18 and n°1 shim P/N G1019-SA700-83. 
11.7.4 In accordance with the applicable step of AMP  
DM 69-A-32-11-01-00A-520B-A, partially extract the LH MLG assy from 
the pintle pin P/N 6F5338A02653 until the forward part of the LH MLG 
assy is disengaged from the pintle pin. 
11.7.5 If the MLG is not equipped with Grease Nipples apply a layer of lubricant 
fluid WD-40 (C245) on the disengaged part of the LH MLG assy and on 
the exposed part of the pintle pin P/N 6F5338A02653, otherwise use 
lubricant Aeroshell 33. 
11.7.6 With reference to Figure 5 view J and in accordance with the applicable 
step of AMP DM 69-A-32-11-01-00A-720B-A, put the LH MLG assy in its 
correct position on the pintle pin P/N 6F5338A02653. Install n°1 shim  
P/N G1019-83, n°1 flange G1019-84, n°6 pins P/N G1019-18 and n°1 
flange P/N G1019-113. 
11.8 With reference to Figure 5 view H, remove n°2 landing lever lock  
P/N 6F3271A01451 from the landing gear control panel removing n°1 screw  
P/N MS27039C1-20, n°2 washers P/N NAS1149D0332K and n°1 nut  
P/N A436A3A1. 
11.9 With reference to Figure 7 view B and view C, remove n°12 rivets  
P/N MS20470E5. 
CAUTION 
Pay particular attention during the removal of the rivets 
P/N MS20470E5, to avoid any damage to the cable 
assemblies located under the EDCU2. 
11.10 With reference to Figure 6 view A, Figure 7 det ail D and Figure 8 detail E, remove 
n°4 rivets P/N MS20470E5. 
11.11 With reference to Figure 8 view G and Figure 11 view P, install n°1 NLG 
retracting actuator P/N 6F3230V00532 on the actuator support P/N G1021-51 by 
means of n°5 bolts P/N AN4-10, n°1 bolt AN3-10, n°5 washers 
P/N NAS1149C0432R, n°1 washers P/N NAS1149C0332R, n°5 nuts 
P/N MS17826-4, n°1 nut P/N MS17826-3 and n°6 cotter pins P/N MS24665-153. 
Torque the bolts P/N AN4-10 to 4 ÷ 5 Nm (35 ÷ 44 lbfin). Torque the bolt  
P/N AN3-10 to 2.5 ÷ 3.5 Nm (22 ÷ 31 lbfin).

### Page 42

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 42 of 138 REVISION: B - April 16, 2018 
NOTE 
With reference to Figure 8 view G, make sure the NLG 
actuator is correct oriented before proceeding with the 
installation. 
11.12 With reference to Figure 8 view G and Figure 11  view N, install the NLG 
retracting actuator P/N 6F3230V00532, as described in the following procedure: 
11.12.1.1 With reference to Figure 11 view N, install n°4 bushes P/N G1021-27 
on the NLG structure. 
NOTE 
Existing pintle pin P/N G1021-71 is necessary to 
perform a correct alignment of the new NLG actuator 
with the NLG rotational axis. NLG centering actuator 
pin P/N 6F3200H00231A023D may be used as a valid 
alternative. 
11.12.2 With reference to Figure 8 view G and Figure 11 view N, install the 
NLG retracting actuator P/N 6F3230V00532 mounted on the support  
P/N G1021-51, on its proper installation position. Use the pintle pin  
P/N G1021-71 as position tool, pulling it all the way in letting it enter 
into the relevant hole in the new NLG actuator. 
11.12.3 With reference to Figure 11 view N, install n°4 bushes  
P/N G1021-49 on the actuator support P/N G1021-51. 
NOTE 
Rotate the n°4 bushes P/N G1021-27 and n°4 bushes 
P/N G1021-49 leaving the pintle pin  
P/N G1021-71 fixed inside the actuator, until the two 
bolts P/N G1021-30 are correctly installed. 
11.12.4 With reference to Figure 11 view N, install n °2 bolts  
P/N G1021-30, n°4 washers P/N NAS1149C0632R, n°2 nuts 
P/N MS17825-6 and n°2 cotter pins P/N MS24665-300. Torque the 
nuts to 25.0 ÷ 30.0 Nm (221 ÷ 266 lbfin). 
11.13 With reference to Figure 31, remove the pintle pin P/N G1021-71 from the NLG 
retracting actuator P/N 6F3230V00532. 
11.14 With reference to Figure 31, install n°1 NLG centering actuator pin  
P/N 6F3200H00231A023C in its correct position in the NLG retracting actuator 
P/N 6F3230V00532 in order to check the correct alignment between the 
rotational axis of NLG actuator and the NLG.

### Page 43

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 43 of 138 
NOTE 
If the rotational axis of NLG actuator and the NLG are 
not properly aligned, remove the NLG retracting 
actuator P/N 6F3230V00532 mounted on the support 
P/N G1021-51 from the NLG assy, and repeat 
step 11.12. Otherwise skip to step 11.15. 
NOTE 
If the removed pintle pin is not P/N G1021-71 skip to 
step 11.16. 
11.15 With reference to Figure 10 view L, disassemble  the removed pintle pin  
P/N G1021-71 removing n°1 cotter pin P/N MS24665-153, n°1 nut  
P/N MS17825-4, n°1 washer P/N NAS1149C0432R, n°1 bolt P/N G1021-48, n°1 
ring nut P/N G1021-62, n°1 laminated washer P/N G1021-72 and n°1 laminated 
washer P/N G1021-73. Replace the pintle pin P/N G1021-71 with the new one 
P/N G1021-64. Reassemble the new pintle pin P/N G1021-64 by means of all the 
attachment hardware previously removed in this step and a new cotter pin  
P/N MS24665-153. Torque the nut to 6.0 ÷ 7.5 Nm (53 ÷ 66 lbfin). 
NOTE 
Do not install clamp P/N MS21919WCE6 and all its 
attaching hardware at this step. 
11.16 In accordance with AMP DM 69-A-32-21-01-00A-720 B-A, install the nose landing 
gear assy in its position on the helicopter structure. 
11.17 With reference to Figure 6 view A, Figure 7 view B and view C, temporary install 
n°1 support assy P/N 6F5331A42331, n°3 peeling shims P/N 6F5331A42951 and 
n°1 peeling shim P/N 6F5331A43051 in their correct positions in the nose gear 
bay. 
11.18 With reference to Figure 32, install n°1 alignment tool P/N 6F3200H00351A651A 
in its correct position on the support assy P/N 6F5331A42331. 
11.19 With reference to Figure 6 view A, Figure 7 view B and view C and Figure 32, 
adjust the dimensions of the n°3 peeling shims P/N 6F5331A42951 andn°1 
peeling shim P/N 6F5331A43051while the alignment tool  
P/N 6F3200H00351A651A is fixed in its installation position. 
11.20 With reference to Figure 32, remove n°1 alignment tool  
P/N 6F3200H00351A651A from the support assy P/N 6F5331A42331. 
11.21 In accordance with AMP DM 69-A-32-21-01-00A-520B-A, remove the nose 
landing gear assy from the helicopter. Retain all the removed attaching hardware

### Page 44

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 44 of 138 REVISION: B - April 16, 2018 
for later reuse. 
NOTE 
The grip length of rivets P/N NAS1720 must be chosen 
during installation in order to get the best fits due to the 
use of peeling shims. 
The grip length reported in part list, procedure and 
figures are typical for this installation. 
11.22 With reference to Figure 6 view A, Figure 7 vie w B and view C, install n°1 support 
assy P/N 6F5331A42331, n°1 peeling shim P/N 6F5331A43051 and n°3 peeling 
shims P/N 6F5331A42951 by means of n°4 rivets P/N NAS1720C5L5W, n°3 rivet 
P/N NAS1720C5L7W, n°1 rivet P/N NAS1720C5L4W, n°8 pin rivets  
P/N HL20PB-5-5 and n°8 collars P/N HL86-5. 
11.23 With reference to Figure 6 view A, Figure 7 detail D and Figure 8 detail E, 
position the support P/N 6F5331A42851 and adjust the thickness of the peeling 
shim P/N 6F5331A43151 as necessary. 
11.24 With reference to Figure 6 view A, Figure 7 detail D and Figure 8 detail E, install 
n°1 support P/N 6F5331A42851 and n°1 peeling shim P/N 6F5331A43151by 
means of n°2 rivets P/N NAS1720C5L4W, n°2 pin rivets P/N HL20PB-5-4, n°4 
pin rivets P/N HL20PB-5-6 and n°6 collars P/N HL86-5. 
NOTE 
Do not install clamp P/N MS21919WCE6 and all its 
attaching hardware at this step. 
11.25 In accordance with AMP DM 69-A-32-21-01-00A-720 B-A, install the nose landing 
gear assy in its position on the helicopter structure. 
11.26 With reference to Figure 10 view L, install the previously removed n°1 bolt  
P/N G1021-78, n°1 washer P/N NAS1149C0432R, n°1 nut P/N MS17825-4 and 
n°1 cotter pin P/N MS24665-88. Torque the nut to 6.0 ÷ 7.5 Nm (53 ÷ 66 lbfin). 
11.27 With reference to Figure 10 view L, install the previously removed n°1 clamp 
P/N MS21919WCE6, n°1 bolt P/N AN3H3A and n°2 washers 
P/N NAS1149C0363R. Torque the bolt to 2.5 ÷ 3.5 Nm (22 ÷ 31 lbfin). 
11.28 With reference to Figure 33, perform the NLG actuator alignment check by 
means of the tool P/N 6F3200H00351A651B, as described in the following 
procedure: 
11.28.1 With reference to Figure 33, put the tool P/N 6F3200H00351A651B in 
its position on the support assy P/N 6F5331A42331.

### Page 45

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 45 of 138 
11.28.2 With reference to Figure 33 section B-B, put n°1 feeler gauge (2,5mm) 
on one side of the tool as shown. 
11.28.3 With reference to Figure 33 section B-B, check if there’s enough 
clearance to put n°1 more feeler gauge (2,5mm) on the other side of 
the tool. If the clearance is enough, skip to step 11.32, otherwise 
proceed with step 11.28.4. 
11.28.4 With reference to Figure 33 section B-B, remove the previously 
installed feeler gauges and check the tool P/N 6F3200H00351A651B 
properly fits within its installation position. If it fits perform step 11.29, 
otherwise contact PSE_AW169.MBX.AW@leonardocompany.com to 
receive proper instructions. 
11.29 With reference to Figure 33, remove n°1 alignment tool  
P/N 6F3200H00351A651B from the support assy P/N 6F5331A42331. 
11.30 With reference to Figure 9 view J, install n°1 double arm pin  
P/N 6F5331A42452 together with n°1 double arm end P/N 6F5331A42552 by 
means of up to n°6 washers P/N 6F5331A44951 distributed on both sides in 
order to ensure the double arm end interfaces with the NLG actuator without 
frictions or lateral loads. 
11.31 Measure the lateral gap on the double arm pin and fix the installation by means 
of n°2 laminated shims P/N A864A1626E024H of a proper thickness and n°1 
cotter pin P/N MS24665-300. Skip to step 11.35. 
11.32 With reference to Figure 33, remove n°1 alignment tool  
P/N 6F3200H00351A651B from the support assy P/N 6F5331A42331. 
11.33 In accordance with AMP DM 69-A-53-15-10-00A-720A-A and with reference to 
Figure 9 view J, install n°1 double arm pin P/N 6F5331A42451, n°2 laminated 
shims P/N A864A1626E024H and n°1 cotter pin P/N MS24665-300. 
11.34 With reference to Figure 9 view J, install n°1 double arm end P/N 6F5331A42551 
in the double arm pin P/N 6F5331A42451. 
11.35 With reference to Figure 34, install n°1 alignment tool P/N 6F3200H00351A651C 
in its correct position on the double arm end, and on the NLG retracting actuator 
P/N 6F3230V00532. 
11.36 With reference to Figure 34, make sure that the lever of the NLG retracting 
actuator P/N 6F3230V00532 and the support assy P/N 6F5331A42331 are 
parallel. If necessary adjust the position of the lever of the NLG retracting 
actuator P/N 6F3230V00532. 
11.37 With reference to Figure 34, remove n°1 alignment tool

### Page 46

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 46 of 138 REVISION: B - April 16, 2018 
P/N 6F3200H00351A651C from the double arm end, and from the NLG retracting 
actuator P/N 6F3230V00532. 
11.38 In accordance with AMP DM 69-A-53-15-09-00A-720A-A and with reference to 
Figure 9 view J, attach the previously installed double arm end to the NLG 
retracting actuator P/N 6F3230V00532 by means of n°1 bolt P/N NAS6606D17, 
n°1 washer P/N NAS1149C0632R, n°1 washer P/N MS20002C6, n°1 nut  
P/N MS21225-6 and n°1 cotter pin P/N MS24665-300. Torque the nut to  
18.1 ÷ 21.5 Nm (160 ÷ 190 lbfin). 
11.39 With reference to Figure 9 detail H, adjust the length of the rod engine assy 
P/N 6F5331A09631 to avoid any preload during the installation of the bolt 
P/N NAS6606D19. 
11.40 With reference to Figure 9 detail H, install n°1 bolt P/N NAS6606D19, n°1 washer 
P/N MS20002C6, n°1 washer P/N A994A45T024H, n°1 bearing sleeve  
P/N 999-0050-02-223, n°1 nut P/N MS21225-6 and n°1 cotter pin  
P/N MS24665-300 that attach the rod engine assy P/N 6F5331A09631 to the 
NLG retracting actuator P/N 6F3230V00532. Torque the nut to 10.7 ÷ 12.4 Nm 
(95-110 lbfin). 
11.41 With reference to Figure 4 and Figure 10, perform the installation of the new MLG 
actuator RH side as described in the following procedure: 
NOTE 
Perform electrical connection of the connector A330P1 
once the MLG actuator is in its installation position and 
not yet attached. 
11.41.1With reference to Figure 10 view M, put the ML G retracting actuator 
P/N 6F3230V01032 on its installation position and perform the electrical 
connection with the existing connector A330P1. 
11.41.2With reference to Figure 10 view M, fix the already positioned MLG 
retracting actuator P/N 6F3230V01032 on the already installed flange  
P/N G1019-113 by means of n°5 bolts P/N NAS1351C4H32 and n°1 bolt 
P/N NAS1351C3H32. Torque the bolts P/N NAS1351C4H32 to 4.0 ÷ 5.0 
Nm (35 ÷ 44 lbfin) and torque the bolt P/N NAS1351C3H32 to 2.5 ÷ 3.2 
Nm (22 ÷ 28 lbfin). Safety the bolts with lockwire P/N MS20995C32. 
11.41.3With reference to Figure 10 view M, fix n°1 MLG retracting actuator RH 
P/N 6F3230V01032 to the pin P/N G1019-44 by means of n°1 peeling 
shim P/N G1019-86, n°1 nut P/N MS17826-6 and n°1 cotter pin  
P/N MS24665-302. Torque the nut to 0.2 Nm (1.8 lbfin). Adjust the

### Page 47

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 47 of 138 
thickness of the peeling shim in order to leave a gap of 0.5 ÷ 0.7. 
11.41.4With reference to Figure 4 view G, restore electrical connection between 
the connectors P332 and J332 under the baggage compartment. 
11.42 With reference to Figure 4 and Figure 10, perform the installation of the new MLG 
actuator LH side as described in the following procedure: 
NOTE 
Perform electrical connection of the connector A341P1 
once the MLG actuator is in its installation position and 
not yet fixed. 
11.42.1With reference to Figure 10 view M, put the ML G retracting actuator 
P/N 6F3230V00832 on its installation position and perform the electrical 
connection with the existing connector A341P1. 
11.42.2With reference to Figure 10 view M, fix the already positioned MLG 
retracting actuator P/N 6F3230V00832 on the already installed flange 
P/N G1019-113 by means of n°5 bolts P/N NAS1351C4H32 and n°1 bolt 
P/N NAS1351C3H32. Torque the bolts P/N NAS1351C4H32 to 4.0 ÷ 5.0 
Nm (35 ÷ 44 lbfin) and torque the bolt P/N NAS1351C3H32 to 2.5 ÷ 3.2 
Nm (22 ÷ 28 lbfin). Safety the bolts with lockwire P/N MS20995C32. 
11.42.3With reference to Figure 10 view M, fix n°1 MLG retracting actuator  
P/N 6F3230V00832 to the pin P/N G1019-44 by means of n°1 peeling 
shim P/N G1019-86, n°1 nut P/N MS17826-6 and n°1 cotter pin  
P/N MS24665-302. Torque the nut to 0.2 Nm (1.8 lbfin). Adjust the 
thickness of the peeling shim in order to leave a gap of 0.5 ÷ 0.7. 
11.42.4With reference to Figure 4 view G, restore electrical connection between 
the connectors P333 and J333 under the baggage compartment. 
12. In accordance with AMP DM 69-A-46-26-02-00A-720A-A and  
DM 69-A-53-17-03-00A-720A-A, reinstall the previously removed EDCU2 and the 
access panel 133AL. 
13. In accordance with AMP DM 69-A-06-40-00-00A-010A-A, install the access panels 
191DL and 192DR. 
14. In accordance with AMP DM 69-A-07-11-00-00A-100A-A, lower the helicopter on the 
ground. 
15. Update the log card of NLG assy P/N 6F3220V00132 adding the NLG actuator  
P/N 6F3230V00532. 
16. Update the log card of LH MLG assy P/N 6F3210V00134 adding the LH MLG actuator 
P/N 6F3230V00832.

### Page 48

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 48 of 138 REVISION: B - April 16, 2018 
17. Update the log card of RH MLG assy P/N 6F3210V00232 adding the new RH MLG 
actuator P/N 6F3230V01032. 
18. In accordance with weight and balance changes, update the Chart A (see Rotorcraft 
Flight Manual, Part II, section 6). 
19. Return the helicopter to flight configuration and record for compliance with Part II of this 
Service Bulletin on the helicopter logbook. 
20. Send the attached compliance form to the following mail box: 
 pse_aw169.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo Web Portal 
and compile the “Service Bulletin Application Communication”.

### Page 49

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 49 of 138 
PART III 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. In accordance with AMP DM 69-A-06-40-00-00A-010A-A, remove access panels 
191DL and 192DR. 
3. In accordance with AMP DM 69-A-07-11-00-00A-100A-A, lift the helicopters on jacks. 
NOTE 
If installed, remove the two decals “LANDING GEAR 
RETRACTION INOPERATIVE” from the two PFDs. 
4. In accordance with IPD DM 69-A-32-31-02-010-941A-A  and with reference to Figure 
10, check the pin P/N G1019-44 is installed on both RH and LH Main Landing Gears. 
NOTE 
Perform the following step 5 if the pins P/N G1019-44 
are not installed on the helicopter. Otherwise, skip to 
step 6. 
5. In accordance with AMP DM 69-A-32-31-12-00A-720A-A , AMP  
DM 69-A-32-31-13-00A-720A-A and with reference to Figure 10, install n°2 pins  
P/N G1019-44 on both RH and LH Main Landing Gears, by means of n°2 washers  
P/N G1019-36, n°2 nuts P/N MS17826-8 and n°2 cotter pins P/N MS24665-155. 
6. With reference to Figure 30, check the laminated washers P/N G1021-72 and  
P/N G1021-73, as described in the following procedure: 
6.1 With reference to Figure 30, measure the thickness of n°2 laminated washers  
P/N G1021-72. Make sure that the thickness of the two laminated washers are 
the same. 
6.2 With reference to Figure 30, measure the thickness of n°2 laminated washers  
P/N G1021-73. Make sure that the thickness of the two laminated washers are 
the same. 
NOTE 
If the check at step 6.1 and step 6.2 is not passed, 
proceed with steps 6.3 and 6.4. Otherwise skip to step 
7. 
6.3 In accordance with AMP DM 69-A-32-21-01-00A-520B- A, remove the nose 
landing gear assy from the helicopter. Retain all the removed attaching hardware 
for later reuse. Discard n°2 laminated washers P/N G1021-72 and n°2 laminated 
washers P/N G1021-73.

### Page 50

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 50 of 138 REVISION: B - April 16, 2018 
6.4 In accordance with AMP DM 69-A-32-21-01-00A-720B-A, reinstall the nose 
landing gear assy in its position on the helicopter structure. Usingn°2 new 
laminated washers P/N G1021-72 and n°2 new laminated washers  
P/N G1021-73. 
7. Perform the check on the NLG lock support buffer as described in the following 
procedure: 
7.1 Measure the gap between NLG and existing NLG lock support buffer 
P/N 6F5331A39251. If gap is 0.10 ÷ 0.40 skip to step 7.3, otherwise perform step 
7.2. 
7.2 With reference to Figure 29 view A, replace the existing buffer with one of the 
followings in order to obtain the correct gap; use rubber adhesive RTV730 (C125) 
then skip to step 7.4: 
• NLG lock support buffer (5.5 mm) P/N 6F5331A44551; 
• NLG lock support buffer (5.0 mm) P/N 6F5331A44651; 
• NLG lock support buffer (4.5 mm) P/N 6F5331A44751; 
• NLG lock support buffer (4.0 mm) P/N 6F5331A44851. 
7.3 Perform the replacement of the adhesive fixing the NLG support buffers, as 
described in the following procedure: 
7.3.1 With reference to Figure 29, temporarily remove the existing NLG lock 
support buffer P/N 6F5331A39251. 
7.3.2 Remove the existing adhesive and properly clean the relevant surface. 
NOTE 
When reinstalling the NLG support buffer, make sure 
the gap between NLG and existing NLG lock support 
buffer P/N 6F5331A39251 is 0.10 ÷ 0.40. 
7.3.3 With reference to Figure 29, reinstall the NLG lock support buffer 
P/N 6F5331A39251 by means of rubber adhesive RTV730 (C125). 
7.4 Perform the replacement of the adhesive fixing the MLG support buffers, as 
described in the following procedure: 
7.4.1 With reference to Figure 29, temporarily remove the existing n°2 MLG 
lock support buffers P/N 6F5280A11051. 
7.4.2 Remove the existing adhesive and properly clean the relevant 
surfaces. 
7.4.3 With reference to Figure 29, reinstall the n°2 MLG lock support buffers 
P/N 6F5280A11051 by means of rubber adhesive RTV730 (C125).

### Page 51

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 51 of 138 
NOTE 
The standoff P/N A388A5E22C75L to be removed is 
the one located on the support assy  
P/N 6F5331A42331. 
8. Remove n°1 screw P/N NAS1802-3-6, n°1 washer P/N N AS1149D0316J, n°1 clamp 
P/N AW001CB05H and n°1 standoff P/N A388A5E22C75L. 
9. With reference to Figure 14, remove and discard the existing Undercarriage cable assy 
P/N 6F3230A00831 and relevant Up-lock Support Buffer P/N 6F5331A38651. 
10. In accordance with AMP DM 69-A-32-21-01-00A-520A-A, remove the nose landing 
gear assy from the helicopter. Retain all the removed attaching hardware for later 
reuse. Put the nose landing gear assy on an applicable work bench. 
11. With reference to Figure 3 thru Figure 5 and Figure 8 thru Figure 11, perform the 
installation of the landing gear actuators as described in the following procedure: 
11.1 With reference to Figure 3 view B, temporarily remove n°1 bolt 
P/N NAS6606D24, n°1 washer P/N MS20002C6, n°1 bearing sleeve  
P/N 999-0050-02-267, n°1 laminated shim P/N A864A0991A018F, n°1 spacer 
P/N NAS43DD6-19N, n°1 laminated shim P/N A864A1308A018F, n°1 washer 
P/N NAS1149C0632R, n°1 nut P/N MS21225-6 and n°1 cotter pin  
P/N MS24665-300. 
NOTE 
If necessary, adjust the position between the NLG strut 
P/N 6F5331A37951 and the rod engine assy  
P/N 6F5331A09631 with peeling shim, on both side. 
11.2 With reference to Figure 5 view K, install n°1 r od engine assy 
P/N 6F5331A09631 by means of previously removed n°1 bolt P/N NAS6606D24, 
n°1 washer P/N MS20002C6, n°1 laminated shim P/N A864A0991A018F, n°1 
bearing sleeve P/N 999-0050-02-267, n°1 laminated shim  
P/N A864A1308A018F, n°1 washer P/N NAS1149C0632R, n°1 nut  
P/N MS21225-6 and n°1 new cotter pin P/N MS24665-300. Torque the nut to 
10.7 ÷ 12.4 Nm (95 ÷ 110 lbfin). 
11.3 With reference to Figure 3 view C and view D, remove and discard n°1 plug 
P/N D38999/33W25N and n°1 plug P/N D38999/33W13R. 
11.4 With reference to Figure 3 view C and view D, if not already installed on the NLG 
strut, install n°1 fairlead P/N G1021-74 and n°1 fairlead P/N G1021-75 as shown. 
11.5 With reference to Figure 3 view C and view D, install n°1 electrical harness 
P/N 6F3230V01331 by means of n°1 clamp P/N MS2191919WCE8and all the ty-

### Page 52

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 52 of 138 REVISION: B - April 16, 2018 
raps as shown. 
11.6 With reference to Figure 4, prepare the installation of MLG actuator RH side as 
described in the following procedure: 
11.6.1 With reference to Figure 4 view G, disconnect the connector P332 and 
loosen the relevant clamp and cable assy C2B125 in order to allow the 
removal of the existing plate assy P/N 6F3210A00131. 
11.6.2 With reference to Figure 4 view F, remove and discard n°1 plate assy 
P/N 6F3210A00131 and n°3 fixing bolts P/N AN4CH7A. 
11.6.3 With reference to Figure 4 view F, remove and discard n°1 fixed flange 
P/N G1019-SA700-82, n°1 flange P/N G1019-SA700-81, n°6 pins  
P/N G1019-SA700-18 and n°1 shim P/N G1019-SA700-83. 
11.6.4 In accordance with the applicable step of AMP  
DM 69-A-32-12-01-00A-520B-A, partially extract the RH MLG assy from 
the pintle pin P/N 6F5338A02653 until the forward part of the RH MLG 
assy is disengaged from the pintle pin P/N 6F5338A02653. 
11.6.5 If the MLG is not equipped with Grease Nipples apply a layer of lubricant 
fluid WD-40 (C245) on the disengaged part of the RH MLG assy and on 
the exposed part of the pintle pin P/N 6F5338A02653, otherwise use 
lubricant Aeroshell 33. 
11.6.6 With reference to Figure 5 view J and in accordance with the applicable 
step of AMP DM 69-A-32-12-01-00A-720B-A, put the RH MLG assy in its 
correct position on the pintle pin P/N 6F5338A02653. Install n°1 shim  
P/N G1019-83, n°1 flange P/N G1020-84, n°6 pins P/N G1019-18 and 
n°1flange P/N G1019-113. Adjust the thickness of the peeling shim 
P/N G1019-83, in order to leave a gap of 0.1 ÷ 0.2 to the MLG. 
11.7 With reference to Figure 4, prepare the installation of MLG actuator LH side as 
described in the following procedure: 
11.7.1 With reference to Figure 4view G, disconnect the connector P333 and 
loosen the relevant clamp and cable assy C2A120 in order to allow the 
removal of the existing plate assy P/N 6F3210A00131. 
11.7.2 With reference to Figure 4 view F, remove and discard n°1 plate assy 
P/N 6F3210A00131 and n°3 fixing bolts P/N AN4CH7A. 
11.7.3 With reference to Figure 4 view F, remove and discard n°1 fixed flange 
P/N G1019-SA700-82, n°1 flange P/N G1019-SA700-81, n°6 pins  
P/N G1019-SA700-18 and n°1 shim P/N G1019-SA700-83. 
11.7.4 In accordance with the applicable step of AMP  
DM 69-A-32-11-01-00A-520B-A, partially extract the LH MLG assy from

### Page 53

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 53 of 138 
the pintle pin P/N 6F5338A02653 until the forward part of the LH MLG 
assy is disengaged from the pintle pin. 
11.7.5 If the MLG is not equipped with Grease Nipples apply a layer of lubricant 
fluid WD-40 (C245) on the disengaged part of the LH MLG assy and on 
the exposed part of the pintle pin P/N 6F5338A02653, otherwise use 
lubricant Aeroshell 33. 
11.7.6 With reference to Figure 5 view J and in accordance with the applicable 
step of AMP DM 69-A-32-11-01-00A-720B-A, put the LH MLG assy in its 
correct position on the pintle pin P/N 6F5338A02653. Install n°1 shim  
P/N G1019-83, n°1 flange P/N G1019-84, n°6 pins P/N G1019-18 and n°1 
flange P/N G1019-113. Adjust the thickness of the peeling shim 
P/N G1019-83, in order to leave a gap of 0.1 ÷ 0.2 to the MLG. 
11.8 With reference to Figure 5 view H, remove and discard n°2 landing lever lock 
P/N 6F3271A01451 from the landing gear control lever, n°1 screw  
P/N MS27039C1-20, n°2 washers P/N NAS1149D0332K and n°1 nut 
P/N A436A3A1. 
11.9 With reference to Figure 8 view G and Figure 11 view P, install n°1 NLG 
retracting actuator P/N 6F3230V00532 on the actuator support P/N G1021-51 by 
means of n°5 bolts P/N AN4-10, n°1 bolt AN3-10, n°5 washers 
P/N NAS1149C0432R, n°1 washers P/N NAS1149C0332R, n°5 nuts 
P/N MS17826-4, n°1 nut P/N MS17826-3 and n°6 cotter pins P/N MS24665-153. 
Torque the bolts P/N AN4-10 to 4 ÷ 5 Nm (35 ÷ 44 lbfin). Torque the bolt  
P/N AN3-10 to 2.5 ÷ 3.5 Nm (22 ÷ 31 lbfin). 
NOTE 
With reference to Figure 8 view G, make sure the NLG 
actuator is correct oriented before proceeding with the 
installation. 
11.10 With reference to Figure 8 view G and Figure 11  view N, install the NLG 
retracting actuator P/N 6F3230V00532, as described in the following procedure: 
11.10.1With reference to Figure 11 view N, install n°4 bushes P/N G1021-27 on 
the NLG structure. 
NOTE 
Existing pintle pin P/N G1021-71 is necessary to 
perform a correct alignment of the new NLG actuator 
with the NLG rotational axis. NLG centering actuator

### Page 54

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 54 of 138 REVISION: B - April 16, 2018 
pin P/N 6F3200H00231A023D may be used as a valid 
al
ternative. 
11.10.2With reference to Figure 8 view G and Figure 1 1 view N, install the NLG 
retracting actuator P/N 6F3230V00532 mounted on the support 
P/N G1021-51, on its proper installation position. Use the pintle pin  
P/N G1021-71 as position tool, pulling it all the way in letting it enter into 
the relevant hole in the new NLG actuator. 
11.10.3With reference to Figure 11 view N, install n°4 bushes P/N G1021-49 on 
the actuator support P/N G1021-51. 
NOTE 
Rotate the n°4 bushes P/N G1021-27 and n°4 bushes 
P/N G1021-49 leaving the pintle pin P/N G1021-71 
fixed inside the actuator, until the two bolts  
P/N G1021-30 are correctly installed. 
11.10.4With reference to Figure 11 view N, install n ° 2 bolts  
P/N G1021-30, n°4 washers P/N NAS1149C0632R, n°2 nuts 
P/N MS17825-6 and n°2 cotter pins P/N MS24665-300. Torque the nuts 
to 25.0 ÷ 30.0 Nm (221 ÷ 266 lbfin). 
11.11 With reference to Figure 31, remove the pintle pin P/N G1021-71 from the NLG 
retracting actuator P/N 6F3230V00532. 
NOTE 
If the rotational axis of NLG actuator and the NLG are 
not properly aligned, remove the NLG retracting 
actuator P/N 6F3230V00532 mounted on the support 
P/N G1021-51 from the NLG assy, and repeat step 
11.10. Otherwise skip to step 11.13. 
11.12 With reference to Figure 31, install n°1 NLG ce ntering actuator pin  
P/N 6F3200H00231A023C in its correct position in the NLG retracting actuator 
P/N 6F3230V00532 in order to check the correct alignment between the 
rotational axis of NLG actuator and the NLG. 
NOTE 
If the removed pintle pin is not P/N G1021-71 skip to 
step 11.14. 
11.13 With reference to Figure 10 view L, disassemble  the removed pintle pin  
P/N G1021-71 removing n°1 cotter pin P/N MS24665-153, n°1 nut  
P/N MS17825-4, n°1 washer P/N NAS1149C0432R, n°1 bolt P/N G1021-48, n°1

### Page 55

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 55 of 138 
ring nut P/N G1021-62, n°1 laminated washer P/N G1021-72 and n°1 laminated 
washer P/N G1021-73. Replace the pintle pin P/N G1021-71 with the new one 
P/N G1021-64. Reassemble the new pintle pin P/N G1021-64 by means of all the 
attachment hardware previously removed in this step and a new cotter pin  
P/N MS24665-153. Torque the nut to 6.0 ÷ 7.5 Nm (53 ÷ 66 lbfin). 
NOTE 
Do not install clamp P/N MS21919WCE6 and all its 
attaching hardware at this stage. 
11.14 In accordance with AMP DM 69-A-32-21-01-00A-720 B-A, install the nose landing 
gear assy in its position on the helicopter structure. 
11.15 With reference to Figure 33, perform the NLG actuator alignment check by 
means of the tool P/N 6F3200H00351A651B, as described in the following 
procedure: 
11.15.1 With reference to Figure 33, put the tool P/N 6F3200H00351A651B in 
its position on the support assy P/N 6F5331A42331. 
11.15.2 With reference to Figure 33 section B-B, put n°1 feeler gauge (2,5mm) 
on one side of the tool as shown. 
11.15.3 With reference to Figure 33 section B-B, check if there’s enough 
clearance to put n°1 more feeler gauge (2,5mm) on the other side of 
the tool. If the clearance is enough, skip to step 11.19, otherwise 
proceed with step 11.15.4. 
11.15.4 With reference to Figure 33 section B-B, remove the previously 
installed feeler gauges and check the tool P/N 6F3200H00351A651B 
properly fits within its installation position. If it fits perform step 11.16, 
otherwise contact PSE_AW169.MBX.AW@leonardocompany.com to 
receive proper instructions. 
11.16 With reference to Figure 33, remove n°1 alignment tool  
P/N 6F3200H00351A651B from the support assy P/N 6F5331A42331. 
11.17 With reference to Figure 9 view J, install n°1 double arm pin  
P/N 6F5331A42452 together with n°1 double arm end P/N 6F5331A42552 by 
means of up to n°6 washers P/N 6F5331A44951 distributed on both sides in 
order to ensure the double arm end interfaces with the NLG actuator without 
frictions or lateral loads. 
11.18 Measure the lateral gap on the double arm pin and fix the installation by means 
of n°2 laminated shims P/N A864A1626E024H of a proper thickness and n°1 
cotter pin P/N MS24665-300. Skip to step 11.22.

### Page 56

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 56 of 138 REVISION: B - April 16, 2018 
11.19 With reference to Figure 33, remove n°1 alignment tool  
P/N 6F3200H00351A651B from the support assy P/N 6F5331A42331. 
11.20 In accordance with AMP DM 69-A-53-15-10-00A-720A-A and with reference to 
Figure 9 view J, install n°1 double arm pin P/N 6F5331A42451, n°2 laminated 
shims P/N A864A1626E024H and n°1 cotter pin P/N MS24665-300. 
11.21 With reference to Figure 9 view J, install n°1 double arm end P/N 6F5331A42551 
in the double arm pin P/N 6F5331A42451. 
11.22 With reference to Figure 34, install n°1 alignment tool P/N 6F3200H00351A651C 
in its correct position on the double arm end and on the NLG retracting actuator 
P/N 6F3230V00532. 
11.23 With reference to Figure 34, make sure that the lever of the NLG retracting 
actuator P/N 6F3230V00532 and the support assy P/N 6F5331A42331 are 
parallel. If necessary adjust the position of the lever of the NLG retracting 
actuator P/N 6F3230V00532. 
11.24 With reference to Figure 34, remove n°1 alignment tool  
P/N 6F3200H00351A651C from the double arm end and from the NLG retracting 
actuator P/N 6F3230V00532. 
11.25 With reference to Figure 10 view L, install the previously removed n°1 bolt  
P/N G1021-78, n°1 washer P/N NAS1149C0432R, n°1 nut P/N MS17825-4 and 
n°1 new cotter pin P/N MS24665-88. Torque the nut to 6.0 ÷ 7.5 Nm (53 ÷ 66 
lbfin). 
11.26 With reference to Figure 10 view L, install the previously removed n°1 clamp 
P/N MS21919WCE6, n°1 bolt P/N AN3H3A and n°2 washers 
P/N NAS1149C0363R. Torque the bolt to 2.5 ÷ 3.5 Nm (22 ÷ 31 lbfin). 
11.27 In accordance with AMP DM 69-A-53-15-10-00A-720A-A and with reference to 
Figure 9view J, attach the previously installed double arm end on the NLG 
retracting actuator P/N 6F3230V00532 by means of n°1 bolt P/N NAS6606D17, 
n°1 washer P/N NAS1149C0632R, n°1 washer P/N MS20002C6, n°1 nut  
P/N MS21225-6 and n°1 new cotter pin P/N MS24665-300. Torque the nut to 
18.1 ÷ 21.5 Nm (160 ÷ 190 lbfin). 
11.28 With reference to Figure 9detail H, adjust the length of the rod engine assy 
P/N 6F5331A09631 to avoid any preload during the installation of the bolt 
P/N NAS6606D19. 
11.29 In accordance with AMP DM 69-A-53-15-09-00A-720A-A and with reference to 
Figure 9detail H, install n°1 bolt P/N NAS6606D19, n°1 washer  
P/N MS20002C6, n°1 washer P/N A994A45T024H, n°1 bearing sleeve  
P/N 999-0050-02-223, n°1 nut P/N MS21225-6 and n°1 cotter pin

### Page 57

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 57 of 138 
P/N MS24665-300 that attach the rod engine assy P/N 6F5331A09631 to the 
NLG retracting actuator P/N 6F3230V00532. Torque the nut to 10.7 ÷ 12.4 Nm 
(95-110 lbfin). 
11.30 With reference to Figure 4 and Figure 10, perform the installation of the new MLG 
actuator RH side as described in the following procedure: 
NOTE 
Perform electrical connection of the connector A330P1 
once the MLG actuator is in its installation position and 
not yet attached. 
11.30.1With reference to Figure 10 view M, put the ML G retracting actuator 
P/N 6F3230V01032 on its installation position and perform the electrical 
connection with the existing connector A330P1. 
11.30.2With reference to Figure 10 view M, fix the already positioned MLG 
retracting actuator P/N 6F3230V01032 on the already installed flange  
P/N G1019-113 by means of n°5 bolts P/N NAS1351C4H32 and n°1 bolt 
P/N NAS1351C3H32. Torque the bolts P/N NAS1351C4H32 to 4.0 ÷ 5.0 
Nm (35 ÷ 44 lbfin) and torque the bolt P/N NAS1351C3H32 to 2.5 ÷ 3.2 
Nm (22 ÷ 28 lbfin). Safety the bolts with lockwire P/N MS20995C32. 
11.30.3With reference to Figure 10 view M, fix n°1 MLG retracting actuator RH 
P/N 6F3230V01032 to the pin P/N G1019-44 by means of n°1 peeling 
shim P/N G1019-86, n°1 nut P/N MS17826-6 and n°1 cotter pin  
P/N MS24665-302. Torque the nut to 0.2 Nm (1.8 lbfin). Adjust the 
thickness of the peeling shim in order to leave a gap of 0.5 ÷ 0.7. 
11.30.4With reference to Figure 4 view G, restore electrical connection between 
the connectors P332 and J332 under the baggage compartment. 
11.31 With reference to Figure 4 and Figure 10, perform the installation of the new MLG 
actuator LH side as described in the following procedure: 
NOTE 
Perform electrical connection of the connector A341P1 
once the MLG actuator is in its installation position and 
not yet attached. 
11.31.1With reference to Figure 10 view M, put the ML G retracting actuator 
P/N 6F3230V00832 on its installation position and perform the electrical 
connection with the existing connector A341P1. 
11.31.2With reference to Figure 10 view M, fix the already positioned MLG 
retracting actuator P/N 6F3230V00832 on the already installed flange

### Page 58

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 58 of 138 REVISION: B - April 16, 2018 
P/N G1019-113 by means of n°5 bolts P/N NAS1351C4H32 and n°1 bolt 
P/N NAS1351C3H32. Torque the bolts P/N NAS1351C4H32 to 4.0 ÷ 5.0 
Nm (35 ÷ 44 lbfin) and torque the bolt P/N NAS1351C3H32 to 2.5 ÷ 3.2 
Nm (22 ÷ 28 lbfin). Safety the bolts with lockwire P/N MS20995C32. 
11.31.3With reference to Figure 10 view M, fix n°1 MLG retracting actuator  
P/N 6F3230V00832 to the pin P/N G1019-44 by means of n°1 peeling 
shim P/N G1019-86, n°1 nut P/N MS17826-6 and n°1 cotter pin  
P/N MS24665-302. Torque the nut to 0.2 Nm (1.8 lbfin). Adjust the 
thickness of the peeling shim in order to leave a gap of 0.5 ÷ 0.7. 
11.31.4With reference to Figure 4view G, restore electrical connection between 
the connectors P333 and J333 under the baggage compartment. 
12. In accordance with AMP DM 69-A-06-40-00-00A-010A-A, reinstall the access panels 
191DL and 192DR. 
13. In accordance with AMP DM 69-A-07-11-00-00A-100A-A, lower the helicopter on the 
ground. 
14. Update the log card of NLG assy P/N 6F3220V00132 adding the NLG actuator  
P/N 6F3230V00532. 
15. Update the log card of LH MLG assy P/N 6F3210V00134 adding the LH MLG actuator 
P/N 6F3230V00832. 
16. Update the log card of RH MLG assy P/N 6F3210V00232 adding the new RH MLG 
actuator P/N 6F3230V01032. 
17. In accordance with weight and balance changes, update the Chart A (see Rotorcraft 
Flight Manual, Part II, section 6). 
18. Return the helicopter to flight configuration and record for compliance with Part III of this 
Service Bulletin on the helicopter logbook. 
19. Send the attached compliance form to the following mail box: 
 pse_aw169.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 59

S.B. N°169-023 ALERT 
DATE: May 31, 2017 
REVISION: B - April 16, 2018 Page 59 of 138 
PART IV 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. In accordance with AMP DM 69-A-95-63-03-00A-520A-A, remove the LH Life Raft 
container assy P/N 6F2560A03231. 
3. In accordance with AMP DM 69-A-06-40-00-00A-010A-A, remove the access panels 
131BL, 132BR, 191AL and 221AL. 
4. In accordance with AMP DM 69-A-32-31-01-00A-520A-A, remove the landing gear 
control panel P/N 6F3230V00432. 
5. With reference to Figures 12 and 13, perform the control box retromod 
P/N 6F3200P01211 as described in the following procedure: 
5.1 In accordance with AMP DM 69-A-32-31-02-00A-520A-A and with reference to 
Figure 12 view A, remove the existing control box P/N 6F3230V01231 or  
P/N 6F3230V01232. 
NOTE 
If the helicopter is equipped with Control Box 
P/N 6F3230V01231, perform the following steps 5.2 
thru 5.13, otherwise skip to step 5.14. 
5.2 With reference to Figure 12 view B and Figure 23 wiring diagram, disconnect and 
locally stow the indicated wires from the existing relay. 
5.3 With reference to Figure 12 view B, remove the relay P/N A657A01, the decal 
P/N ED300K221, the support P/N AW001CL001-N6 and the spacer 
P/N A631A01B. 
5.4 With reference to Figure 12 view B, remove the bracket P/N A815A04A1 and 
relevant n°2 rivets P/N NAS1720H4L2A. 
5.5 With reference to Figure 12 view A and Figure 23 wiring diagram, disconnect and 
locally stow the existing wires from A289P1 connector pins d, p, J. 
5.6 With reference to Figure 12 view A and Figure 23 wiring diagram, remove the 
existing caps CP210, CP212, CP214 from the WH wires118, 128, 136. Restore 
the electrical connections between the WH wires118, 128, 136 and the A289P1 
connector pins d, p, J. 
5.7 With reference to Figure 13 cockpit LH side view and Figure 23 wiring diagram, 
disconnect and locally stow the existing wires from A206P2 connector. 
5.8 With reference to Figure 13 cockpit LH side view and Figure 23 wiring diagram, 
disconnect and locally stow the existing wire 277 from J247 connector.

### Page 60

S.B. N°169-023 ALERT 
 DATE: May 31, 2017 
Page 60 of 138 REVISION: B - April 16, 2018 
5.9 With reference to Figure 13 cockpit LH side view and Figure 23 wiring diagram, 
remove the existing cap CP211 from the WH wire 118 and restore the electrical 
connection with J247 connector pin N. 
5.10 With reference to Figure 13 view C and Figure 23 wiring diagram, disconnect and 
locally stow the existing wire 279 from J246 connector. 
5.11 With reference to Figure 13 view C and Figure 23 wiring diagram, remove the 
existing cap CP215 from the WH wire 136 and restore electrical connection with 
J246 connector pin A. 
5.12 With reference to Figure 13 view D and Figure 23 wiring diagram, disconnect and 
locally stow the existing wire 278 from J287 connector. 
5.13 With reference to Figure 13 view D and Figure 23 wiring diagram, remove the 
existing cap CP213 from the WH wire 128 and restore electrical connection with 
J287 connector pin A. 
5.14 In accordance with AMP DM 69-A-32-31-02-00A-720A-A and with reference to 
Figure 12 view A, install the control box P/N 6F3230V01233. 
6. In accordance with AMP DM 69-A-32-31-01-00A-720A-A, install the landing gear control 
panel P/N 6F3230V00432. 
7. In accordance with AMP DM 69-A-06-40-00-00A-010A-A, install the access panels 
131BL, 132BR, 191AL and 221AL. 
8. In accordance with AMP DM 69-A-95-63-03-00A-720A-A, install the LH Life Raft 
container assy P/N 6F2560A03231. 
9. In accordance with weight and balance changes, update the Chart A (see Rotorcraft 
Flight Manual, Part II, section 6). 
10. Return the helicopter to flight configuration and record for compliance with Part IV of this 
Service Bulletin on the helicopter logbook. 
11. Send the attached compliance form to the following mail box: 
 pse_aw169.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

The text continues at https://openairdocs.org/service-documents/leonardo/sb-169-023/file/d2657fccef7e.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
