# Leonardo Alert Service Bulletin 169-148: Revision B

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-0612, the docket of AD 2021-20-17. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 169-148](https://openairdocs.org/service-documents/leonardo/sb-169-148.md)
- Title as filed: Leonardo Helicopters Emergency ASB No. 169-148 Rev B
- Pages: 37
- PDF: https://openairdocs.org/files/sha256/15/0b/150b7aaa372bf13788f4cd3a3036758626e25c330af7629d66c48414fe7d1cac
- Page: https://openairdocs.org/service-documents/leonardo/sb-169-148/file/150b7aaa372b

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N° 169-148
DATE:  May 29, 2019 
REV. :  B -  February 4, 2020 
Page 1 of 36 
TITLE 
ATA 64 - TAIL ROTOR FLIGHT CONTROL IMPROVED PERIODICAL INSPECTION 
REVISION LOG 
Revision B of this Service Bulletin cancels and supersedes all the previous Revisions. 
Revision A is issued to: 
• Update the “Compliance” section clarifying the note rel evant to accomplishment of
Part VI;
• Update cross-reference in Part V step 4;
• Provide instruction to remove the castellated nut in pl ace of loosen it while
performing the replacement of the TR duplex bearing;
• Add closure action in case of findings after accomplishment with Part VI step 3;
• Add cleaning instruction of the TR duplex bearing are a in Part V before installation
of the spider plug
• Add details to cleaning procedure of spacer control rod su rface with aliphatic
naphtha
• Add note for accessibility to inspection Area in Part I.
• In case of no-findings after the inspections, it is not r equired anymore to send
feedback to LHD.
• Add HUMS data download in case TRA HUMS accelerometer h as been already
installed to helicopter.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
EMERGENCY ALERT
SERVICE BULLETIN

### Page 2

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 2 of 36 REVISION: B - February 4, 2020 
• Update the reference to Annex A - UTC Microtecnica Ser vice Bulletin 67-0006 Issue 
1. 
 
Revision B is issued in order to introduce the following changes: 
• Change effectivity for Part I from “All AW 169 hel icopters” to “All AW 169 helicopters 
equipped with TRA P/N 6F6730V00331”; 
• Remove Annex A and all the references to the subject  document, as all the relevant 
information is now enclosed in applicable AMP Data Modules. 
 
Revision bars in the margins identify changes.

### Page 3

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 3 of 36 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
Part I: All AW169 helicopters equipped with TRA P/N 6F6730V00331. 
Part II: All AW169 helicopters. 
Part III: All AW169 helicopters. 
Part IV: All AW169 helicopters. 
Part V: All AW169 helicopters. 
Part VI: All AW169 helicopters. 
B. COMPLIANCE 
Part I:  
Within 10 FH from last application of Part I of SB 16 9-135 or from the issue of this 
Service Bulletin, whichever occurs first. Then repeat the inspection every 10 FH. 
NOTE 
Every time it is required to perform Part II, 
accomplishment of Part I, Part IV and Part V on the 
same maintenance downtime, must be performed as a 
prerequisite. If Part III is required in the same 
maintenance downtime, it shall be performed lastly. 
Part II:  
Within 50 FH from last application of Part II of SB 1 69-135 or from the issue of this 
Service Bulletin, whichever occurs first. Then repeat the inspection every 50 FH. 
Part III:  
Within 20 FH from last application of Part III of SB 169-135 or from the issue of this 
Service Bulletin, whichever occurs first, then repeat the installation every 20 FH. 
Part IV:  
Within 10 FH from last application Part IV of SB 169- 135 or from the issue of this 
Service Bulletin, whichever occurs first. Then repeat the inspection every 10 FH. 
NOTE 
Perform as a prerequisite Part I and Part IV. 
If Part III is required in the same maintenance 
downtime, it shall be performed lastly. 
Part V:  
Within 10 FH from last application of Part I of SB 16 9-135 or from the issue of this 
Service Bulletin, whichever occurs first. Then repeat the inspection every 10 FH.

### Page 4

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 4 of 36 REVISION: B - February 4, 2020 
 
NOTE 
• After the first accomplishment of Part VI repeat 
Part VI phased with Part II, not exceeding 
200FH from the first application of the Part VI. 
Then repeat every 200FH. 
• Perform in sequence Part I, Part IV, Part V as a 
prerequisite. 
• If Part II is required in the same maintenance 
downtime, it shall be performed after Part V and 
before Part VI. 
• If Part III is required in the same maintenance 
downtime, it shall be performed after Part VI. 
Part VI:  
Within 10 FH from last application of Part I of SB 16 9-135 or from the issue of this 
Service Bulletin, whichever occurs first. Then repeat the inspection every 200 FH. 
C. CONCURRENT REQUIREMENTS 
This SB supersedes and replaces the SB 169-135. 
D. REASON 
This Service Bulletin is issued in order to require the  periodical inspection of the 
slippage marking of the back-end castellated nut of th e TR servo-actuator and the 
periodical detailed inspection of the TR duplex bearing. 
E. DESCRIPTION 
Following additional tests and the completion of the i nitial phase of the in service 
monitoring carried out on the AW169 and AW189 fleet,  it has been confirmed that the 
introduction of a temperature monitoring represents an  effective independent measure 
to confirm the health of the TR bearing. In addition  a refinement of the current 
inspection schedule is required with this SB along with the introduction of an additional 
instruction for duplex bearing roughness check. 
This Service Bulletin provides the instructions for the above together with the transition 
to the new inspection regime. 
In details Part I of this Service Bulletin provides the  periodical detailed inspection of 
the slippage marking of the castellated nut installed on the back end of the TRA.

### Page 5

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 5 of 36 
Part II partly retains the requirement of the Part I I of the SB 169-135 defining the 
required detailed inspection requirement of TR duplex bearing.  
Part III provides the instructions to install a dedicated  thermal strip in the area of the 
TR duplex bearing.  
Part IV provides the instructions to recursively check the thermal strip. 
Part V requires the verification of metallic particle presence in the grease that could be 
found on the visible part of the duplex bearing. Thi s check was already present in the 
Part II of the SB 169-135 and it is now confirmed with a tighter compliance. 
Part VI prescribes an additional roughness check of the d uplex bearing to be 
performed after removal of the spider assembly. 
Incorrect installation of the TR servo-actuator back-end nut or seizure of the TR duplex 
bearing may lead to loss of Tail Rotor control which, depending on the flight condition, 
could lead to loss of control of the aircraft. 
Feedback on the compliance to this Service Bulletin is required. 
Revision A of this Service Bulletin allows the simplif ication of Part I inspection and 
reduce the amount of feedback required after “no-findings” inspections. 
F. APPROVAL 
The technical content of this Service Bulletin is approve d under the authority of DOA 
nr. EASA.21.J.005. For helicopters registered under oth er Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Auth ority approval must be checked 
within Leonardo Helicopters customer portal. 
E.A.S.A. states mandatory compliance with inspections, mod ifications or technical 
directives and related time of compliance by means of rel evant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a m odification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incor poration of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin the following MMH are deemed necessary: 
Part I: approximately one (0.5); 
Part II: approximately three (3); 
Part III: approximately half (0.5); 
Part IV: approximately one (1);

### Page 6

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 6 of 36 REVISION: B - February 4, 2020 
Part V: approximately one (0.5); 
Part VI: approximately three (3); 
 
MMH are based on hands-on time and can change with per sonnel and facilities 
available. 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE DESCRIPTION PART 
DM01 69-A-00-20-00-00A-120A-A Helicopter on ground f or a safe 
maintenance. 
I, II, III, 
IV, V, VI 
DM02 69-A-06-40-00-00A-010A-A Access door provision  I, II 
DM03 69-A-64-31-01-00A-520A-A Pitch link - Remove pro cedure II 
DM04 69-A-64-21-05-00A-520A-A Lightning conductor jum per – 
Remove procedure 
II 
DM05 69-A-64-31-03-00A-520A-A Spider plug - Remove procedure II, III, IV, 
V, VI 
DM06 69-A-64-31-03-00A-720A-A Spider plug - Install  procedure II, III, IV, 
V, VI 
DM07 69-A-64-31-02-00A-520A-A Scissors group – Remove 
procedure 
II 
DM08 69-A-64-31-07-00A-520A-A Boot - Remove procedur e II 
DM09 69-A-64-31-04-00A-520A-A Sliding control assy – R emove 
procedure 
II, VI 
DM10 69-A-64-31-04-00A-720A-A Sliding control assy – I nstall 
procedure 
II, VI 
DM11 69-A-64-31-05-00A-520A-B Duplex bearing - Remo ve 
procedure 
II, IV, V, 
VI 
DM12 69-A-64-31-05-00A-720A-B Duplex bearing - Insta ll procedure II, IV, V, 
VI 
2) ACRONYMS 
SB Service Bulletin 
DM Data Module 
DOA Design Organization Approval 
EASA European Aviation Safety Agency 
LHD Leonardo Spa Helicopters

### Page 7

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 7 of 36 
MMH Maintenance Man Hours 
SB Service Bulletin 
FH Flight Hours 
TR Tail Rotor 
TRA Tail Rotor Actuator 
3) ANNEX 
N.A. 
J. PUBLICATIONS AFFECTED 
N.A. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 8

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 8 of 36 REVISION: B - February 4, 2020 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
Refer to AW169 IPD for the spares materials required t o comply with the AMP DMs 
referenced in the accomplishment instructions. 
2) CONSUMABLES 
The following consumable materials, or equivalent, are  necessary to accomplish this 
Service Bulletin: 
# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 
1 Thermax 8 Level strip indicator code No.26805  Thermal strip AR (1)(2)(3) III,IV 
2 TT-N-95-B / Code No. 531055030 Aliphatic Naphtha (C059) AR (1) III,IV 
 
Refer to AW169 AMDI for the consumables required to com ply with the AMP DMs 
referenced in the accomplishment instructions. 
3) LOGISTIC MATRIX 
N.A. 
NOTE 
(1) Item to be furnished as local supply. 
(2) Thermal strip Thermax 5 Level clock style indicat or code No.26004 may be used 
as a valid alternative. 
(3) The use of further alternative strip is allowed pr ovided that it complies with the 
following requirements: 
• Irreversible temperature indication. 
• Self-Adhesive. 
• Temperature Range shall be included within 100°C – 1 60°C provided that it 
shows a discrete level at 121±2°C. 
• Overall measurement accuracy: ±2°C. 
• The maximum allowed length to prevent overlap is 80  mm. 
In case any clarification is needed, contact the Product S upport Engineering 
(pse_aw169.mbx.aw@leonardocompany.com).

### Page 9

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 9 of 36 
B. SPECIAL TOOLS 
Refer to ITEP for the special tools required to comply with the AMP DMs referenced in 
the accomplishment instructions. 
C. INDUSTRY SUPPORT INFORMATION 
Owners/Operators who comply with the instructions of this Service Bulletin no later 
than the applicable date in the “Compliance” section wi ll be eligible to receive 
REQUIRED MATERIALS on free of charge basis, except for Consumable Materials 
and Special Tools.  
NOTE: Customers who fail to comply with the instructions in this Service Bulletin 
before the compliance date are not eligible for the aforementioned special policy.  
Please Issue relevant MMIR form to your Warranty Administration Dpt.  
NOTE: WRM will include RETURN MATERIAL AUTHORIZATION  (RMA) number; the 
unit disembarked from the aircraft has to be returned to LHD within thirty (30) calendar 
days after the shipment of the replacement part. In case  of missing return within thirty 
(30) calendar days, Customer will be invoiced for the price of the replacement part.

### Page 10

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 10 of 36 REVISION: B - February 4, 2020 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the 
modification area and adequately protect them until 
their later re-use. 
PART I 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A,  prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, a ll electrical power sources 
and/or the external power supply. 
NOTE 
Removal of access panels 470AT and 470BT can be 
avoided if visual access to the inspection area is 
available by other means. A suitable borescope can be 
used for this purpose. 
2. In accordance with AMP DM 69-A-06-40-00-00A-010A-A remove the access panels 
470AT and 470BT. 
3. Take a picture of the back-end area of the TRA clear ly showing the slippage mark, and 
keep a record in a local archive to be made available if required. 
4. With reference to Figure 3, check the slippage mark o n the castellated nut for absence 
of evidence of rotation between the parts. Record the result on Table I (refer to Figure 
7). 
5. If any evidence of rotation is found, contact the Pr oduct Support Engineering  
(pse_aw169.mbx.aw@leonardocompany.com), wait for further instructions before to 
perform the following checks: 
5.1 Perform Part II of this SB; 
5.2 Perform Part V of this SB;  
5.3 Send the picture taken at step 3 to Product Suppo rt Engineering 
(pse_aw169.mbx.aw@leonardocompany.com). 
5.4 If the helicopter is already compliant with the SB  169-140, perform HUMS data 
download from AMMC to DTD. Upload the HUMS data to Heliwise. 
6. If no evidence of rotation is found in step 4, ret urn the helicopter to a ready to flight 
condition and record for compliance with Part I of this Service Bulletin on the helicopter 
logbook.

### Page 11

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 11 of 36 
7. Send the attached compliance form and the compiled T able I to the following mail box:  
pse_aw169.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 12

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 12 of 36 REVISION: B - February 4, 2020 
PART II 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A,  prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, a ll electrical power sources 
and/or the external power supply. 
NOTE 
If not damaged, the O-ring removed in the following  
step can be retained for later reinstallation. 
2. In accordance with AMP DM 69-A-64-31-03-00A-520A-A,  remove the spider plug. 
3. In accordance with AMP DM 69-A-64-31-01-00A-520A-A,  remove all the pitch links from 
the TR. 
4. In accordance with applicable steps of AMP DM 69-A-64- 31-02-00A-520A-A, disconnect 
the upper half scissors from the spider. 
5. In accordance with applicable steps of AMP DM 69-A-64- 31-07-00A-520A-A, disconnect 
and lower the boot from the spider. 
6. In accordance with AMP DM 69-A-64-21-05-00A-520A-A,  disconnect the TR lightning 
conductor jumper. 
7. Perform the inspection of the TR duplex bearing in accordance with the following 
procedure: 
7.1 Inspect the visible part of the TR duplex bearing (including the seals) for absence 
of wear, damages and security of attachment. Record the results on Table II 
(refer to Figure 8). 
7.2 Check for absence of axial play when trying to move t he spider along the control 
rod axis. Record the result on Table II (refer to Figure 8). 
NOTE 
With reference to Figure 1 and Figure 2 View B and 
Detail C, apply a 25 ± 2.5 N upward force on the 
squared rod end by means of a dynamometer while 
performing the instructions reported in steps from 7.3 
to 7.7. It is allowed to apply the force either pushin g or 
pulling the rod end with the dynamometer. 
7.3 Perform at least three (3) complete and continuous revolutions of the spider both 
in clockwise and in counterclockwise directions and verify that the spider has a 
free and easy rotation. Record the result on Table II (refer to Figure 8). 
7.4 Put one arm of the spider along the vertical posit ion; locate a dynamometer 
gauge on the spider arm hole (pitch link upper bolt l ocation). Hold the gauge 
perpendicular to the spider arm surface. Gently push rig htward the device until a

### Page 13

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 13 of 36 
slight rotation of the spider occurs (see Figures 1 and 2  for further details and 
dynamometer positioning). Record the force measured on Table II (refer to 
Figure 8). 
7.5 Repeat step 7.4 for the opposite spider rotation o n the same arm, pushing 
leftward the dynamometer gauge from the vertical posi tion of the spider arm. 
Record the force measured on Table II (refer to Figure 8). 
7.6 Repeat steps 7.4 and 7.5 for all the other two sp ider arms. 
7.7 The force detected by dynamometer on steps 7.4 thru  7.6 shall be measured 
within 1.6 N and 8.8 N. 
8. If none of the checks performed in step 7 fails procee d as follows, otherwise skip to 
step 9. 
NOTE 
Removal of access panels 470AT and 470BT can be 
avoided if visual access to the inspection area is 
available by other means. A suitable borescope can be 
used for this purpose. 
8.1 In accordance with AMP DM 69-A-06-40-00-00A-010A-A  remove the access 
panels 470AT and 470BT. 
8.2 With reference to Figure 3, check the slippage mar k on the castellated nut for 
absence of evidence of rotation between the parts. If a ny evidence of rotation is 
found, immediately contact the PSE 
(pse_aw169.mbx.aw@leonardocompany.com) and wait for further instructions. 
8.3 If helicopter is already compliant with the SB 169 -140, perform HUMS data 
download from AMMC to DTD. Upload the HUMS data to Heliwise. 
8.4 Skip to step 13. 
9. If one of the checks performed from step 7.1 to 7.2  fails skip to step 11, otherwise 
proceed with the following step 10. 
10. If one of the checks performed from step 7.3 to  step 7.7 fails proceed as follows: 
10.1 Perform the cleaning procedure of the sliding cont rol assy in accordance with the 
following procedure: 
10.1.1 In accordance with AMP DM 69-A-06-40-00-00A-010 A-A remove the 
access panels 470AT and 470BT. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end.

### Page 14

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 14 of 36 REVISION: B - February 4, 2020 
10.1.2 In accordance with AMP DM 69-A-64-31-04-00A-520 A-A, remove the 
sliding control assy. 
10.1.3 Clean the external surface of the sliding contro l assy by means of soft 
lint-free cloth. 
10.1.4 Clean the accessible internal surface of the slider  bushing by means of 
soft lint-free cloth. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
10.1.5 In accordance with AMP DM 69-A-64-31-04-00A-720A -A, reinstall the 
sliding control assy. 
10.1.6 With reference to Figure 3, restore the slippa ge marking on the 
castellated nut from the hinge bracket element to the rod. 
10.2 Repeat steps from 7.2 to 7.7 to verify the absence  of axial play of TR duplex 
bearing and to perform again the roughness and breaka way force checks of TR 
duplex bearing. 
10.3 If any of the checks performed in step 10.2 fail s proceed with the following 
step 11, otherwise skip to step 13. 
11. Contact immediately the Product Support Engineeri ng 
(pse_aw169.mbx.aw@leonardocompany.com) to receive further instruction before 
performing the replacement of the TR duplex bearing in accordance with the following 
procedure: 
11.1 If helicopter is already equipped compliant with the SB 169-140, perform HUMS 
data download from AMMC to DTD. Upload the HUMS data to Heliwise. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
NOTE 
Before removal of the TR duplex bearing, take note of 
its installation orientation marking “OUT” on the 
outboard visible face.After removal mark “IN” on the 
inboard opposite face of the TR duplex bearing. Use 
an indelible pen. 
11.2 In accordance with AMP DM 69-A-64-31-05-00A-520A- B, remove the TR duplex

### Page 15

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 15 of 36 
bearing. 
11.3 Collect the grease leaked from the TR duplex beari ng “IN” marked side in a 
container different from the one used before. 
11.4 Take a picture of both faces of the removed TR du plex bearing and send them to 
PSE (pse_aw169.mbx.aw@leonardocompany.com) before returning the bearing. 
11.5 Clean by means of a soft lint-free cloth the housi ng of the TR duplex bearing, the 
rod visible part and the internal side of the spider plug. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
11.6 In accordance with AMP DM 69-A-64-31-05-00A-720A-B , install a new TR duplex 
bearing. 
11.7 With reference to Figure 3, restore the slippage marking on the castellated nut 
from the hinge bracket element to the rod. 
12. In case replacement of the TR duplex bearing is req uired, please return immediately 
(within 2 days) the removed TR duplex bearing and th e collecting containers of the 
grease to Leonardo Helicopters. Contact the Product Su pport Engineering 
(pse_aw169.mbx.aw@leonardocompany.com) to receive the proper instructions to 
return the removed component. 
NOTE 
When performing the following step allow the sealant 
to cure for at least 2 hours before the next flight. 
13. In accordance with AMP DM 69-A-64-31-03-00A-720A-A , install the spider plug. 
NOTE 
In case of any findings, report within 2 days the 
inspection results along with the available records of 
the previous checks. 
14. Send the attached compliance form and the compiled Table II to the following mail box: 
pse_aw169.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”. 
15. Return the helicopter to a ready to flight condit ion and record for compliance with Part II 
of this Service Bulletin on the helicopter logbook.

### Page 16

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 16 of 36 REVISION: B - February 4, 2020 
PART III 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A,  prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, a ll electrical power sources 
and/or the external power supply. 
2. In accordance with AMP DM 69-A-64-31-03-00A-520A-A,  remove the spider plug. 
3. With reference to Figure 4, perform the installati on of thermal strip Thermax 8 level strip 
No.26805 or equivalent as follows: 
3.1 Clean the spacer control rod P/N 4F6430A02551 surfa ce with a soft lint-free cloth 
soaked with a small quantity of aliphatic naphtha. The n dry the surface with a 
clean cloth. 
3.2 With reference to Figure 5, if the selected therma l strip exceeds the height of 16 
mm it shall be cut taking care not to remove the Celsius scale and not to damage 
the sensitive elements of the strip. 
CAUTION 
When installing the thermal strip pay attention to: 
• avoid contact with bearing gaskets; 
• ensure a good adhesion with the spacer control 
rod P/N 4F6430A02551; 
• all temperature indicators of the thermal strip 
shall be visible. 
CAUTION 
If thermal strip trimming is required, confirm that the cut 
did not cause debonding of strip layers. 
3.3 With reference to Figure 4, with the help of a n on metallic spatula, perform the 
installation of the thermal strip on the surface of the  spacer control rod P/N 
4F6430A02551. 
NOTE 
When performing the following step allow the sealant 
to cure for at least 2 hours before the next flight. 
4. In accordance with AMP DM 69-A-64-31-03-00A-720A-A,  install the spider plug. 
5. Return the helicopter to a ready to flight conditi on and record for compliance with Part III 
of this Service Bulletin on the helicopter logbook. 
6. Send the attached compliance form to the following mail box:  
pse_aw169.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 17

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 17 of 36 
PART IV 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A,  prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, a ll electrical power sources 
and/or the external power supply. 
2. In accordance with AMP DM 69-A-64-31-03-00A-520A-A,  remove the spider plug. 
3. With reference to Figure 4, check the thermal strip  for good adhesion and readability and 
proceed as follows: 
3.1 If the thermal strip is properly installed proceed with step 4; 
3.2 If the strip is detached, partially detached or un readable perform the TR duplex 
bearing inspection in accordance with accomplishment instructions from step 3 to 
step 14 of Part II of this SB; 
3.3 Replace the thermal strip in accordance with step 3 of Part III of this SB; 
3.4 Skip to step 6. 
CAUTION 
In case the selected thermal strip does not provide a 
discrete value equal to 121°C, select the lowest value 
comprised within the range 121±2°C. 
4. With reference to Figure 4, check the temperature r eached by the thermal strip installed 
on spacer control rod P/N 4F6430A02551. Make sure that the temperature has not 
reached a value equal to or above 121°C. Record the ch eck result on Table III (refer to 
Figure 9). 
5. If temperature has exceeded a value equal to or ab ove 121°C, perform the following 
steps, otherwise skip to step 6: 
5.1 If the helicopter is already compliant with the SB  169-140, perform HUMS data 
download from AMMC to DTD. Upload the HUMS data to Heliwise. 
5.2 Contact immediately the Product Support Engineer ing 
(pse_aw169.mbx.aw@leonardocompany.com) to receive further instruction 
before thermal strip and duplex bearing removal and replacement.  
5.3 Perform from step 3 to step 14 of Part II of this SB. 
5.4 Perform from step 3 to step 9 of Part V of this SB . 
5.5 Remove the spacer control rod P/N 4F6430A02551, w ithout removing the 
thermal strip. 
5.6 Take a picture of the thermal strip, installed on  the removed spacer control rod 
P/N 4F6430A02551 and send it to PSE 
(pse_aw169.mbx.aw@leonardocompany.com).

### Page 18

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 18 of 36 REVISION: B - February 4, 2020 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
NOTE 
Before removal of the TR duplex bearing, take note of 
its installation orientation marking “OUT” on the 
outboard visible face. 
After removal mark “IN” on the inboard opposite face of 
the TR duplex bearing. 
Use an indelible pen. 
5.7 In accordance with AMP DM 69-A-64-31-05-00A-520A-B , remove the TR duplex 
bearing. 
5.8 Collect the grease leaked from the TR duplex bearin g “IN” marked side in a 
container different from the one used before. 
5.9 Take a picture of both faces of the removed TR dup lex bearing and send them to 
PSE (pse_aw169.mbx.aw@leonardocompany.com) before returning the bearing. 
5.10 Clean by means of a soft lint-free cloth the housi ng of the TR duplex bearing, the 
rod visible part and the internal side of the spider plug 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
5.11 In accordance with AMP DM 69-A-64-31-05-00A-720A-B , install a new TR duplex 
bearing. 
5.12 In accordance with AMP DM 69-A-64-31-04-00A-720A- A, reinstall the sliding 
control assembly. 
5.13 With reference to Figure 3, restore the slippage marking on the castellated nut 
from the hinge bracket element to the rod. 
5.14 In case replacement of the TR duplex bearing is re quired, please return 
immediately (within 2 days) the removed TR duplex be aring, the collecting 
containers of the grease and the thermal strip to Leona rdo Helicopters. Contact 
the Product Support Engineering ( pse_aw169.mbx.aw@leonardocompany.com) 
to receive the proper instructions to return the removed component. 
5.15 Go to Step 6. 
NOTE

### Page 19

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 19 of 36 
When performing the following step allow the sealant 
to cure for at least 2 hours before the next flight. 
6. In accordance with AMP DM 69-A-64-31-03-00A-720A-A,  install the spider plug. 
7. Return the helicopter to a ready to flight conditi on and record for compliance with Part IV 
of this Service Bulletin on the helicopter logbook. 
NOTE 
In case of any findings, report within 2 days the 
inspection results along with the available records of 
the previous checks. 
8. Send the attached compliance form and the compiled T able III to the following mail box: 
pse_aw169.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 20

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 20 of 36 REVISION: B - February 4, 2020 
PART V 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A,  prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, a ll electrical power sources 
and/or the external power supply. 
NOTE 
If not damaged, the O-ring removed in the following  
step can be retained for later reinstallation. 
2. In accordance with AMP DM 69-A-64-31-03-00A-520A-A,  remove the spider plug. 
3. Perform a detailed inspection of the TR duplex bea ring in accordance with the following 
procedure: 
3.1 Check the visible part of the TR duplex bearing fo r particles absence. 
CAUTION 
Pay attention not to damage the thermal strip durin g 
the grease sampling from the bearing housing. 
3.2 Check the visible part of the TR duplex bearing a nd/or the spider plug for grease 
leakage and confirm absence of any particles by finger touch. 
3.3 Put a small quantity of grease using a small spatul a in a transparent container 
and add a solvent (aliphatic naphtha). Then by using a  magnet on the bottom out 
side of the container check for presence of magnetic particles. 
3.4 Record the result on Table IV (refer to Figure 1 0) and collect the grease leaked 
from the visible surface in a proper container. 
4. If magnetic metallic and/or any other particles are found during accomplishment of step 
3 proceed with the following step 5, otherwise skip to step 7. 
5. Perform from step 3 to step 14 of Part II of this S B.  
6. Contact immediately the Product Support Engineerin g 
(pse_aw169.mbx.aw@leonardocompany.com) to receive further instruction before 
performing the replacement of the TR duplex bearing in accordance with the following 
procedure: 
6.1 If helicopter is already compliant with the SB 169 -140, perform HUMS data 
download from AMMC to DTD. Upload the HUMS data to Heliwise. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end.

### Page 21

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 21 of 36 
NOTE 
Before removal of the TR duplex bearing, take note of 
its installation orientation marking “OUT” on the 
outboard visible face. 
After removal mark “IN” on the inboard opposite face of 
the TR duplex bearing. 
Use an indelible pen. 
6.2 In accordance with AMP DM 69-A-64-31-05-00A-520A-B , remove the TR duplex 
bearing. 
6.3 Collect the grease leaked from the TR duplex bearin g “IN” marked side in a 
container different from the one used before. 
6.4 Take a picture of both faces of the removed TR dup lex bearing and send them to 
PSE (pse_aw169.mbx.aw@leonardocompany.com) before returning the bearing. 
6.5 Clean by means of a soft lint-free cloth the housin g of the TR duplex bearing, the 
rod visible part and the internal side of the spider plug. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
6.6 In accordance with AMP DM 69-A-64-31-05-00A-720A-B , install a new TR duplex 
bearing. 
6.7 With reference to Figure 3, restore the slippage m arking on the castellated nut 
from the hinge bracket element to the rod. 
7. In case replacement of the TR duplex bearing is requ ired, please return immediately 
(within 2 days) the removed TR duplex bearing and th e collecting containers of the 
grease to Leonardo Helicopters. Contact the Product Su pport Engineering 
(pse_aw169.mbx.aw@leonardocompany.com) to receive the proper instructions to 
return the removed component. 
8. Clean the visible surface of the TR duplex bearing by means of soft lint-free cloth. 
NOTE 
When performing the following step allow the sealant 
to cure for at least 2 hours before the next flight. 
9. In accordance with AMP DM 69-A-64-31-03-00A-720A-A,  install the spider plug. 
10. Return the helicopter to a ready to flight condit ion and record for compliance with Part V 
of this Service Bulletin on the helicopter logbook.

### Page 22

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 22 of 36 REVISION: B - February 4, 2020 
NOTE 
In case of any findings, report within 2 days the 
inspection results along with the available records of 
the previous checks. 
11. Send the attached compliance form and the compiled Table IV to the following mail box: 
pse_aw169.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”

### Page 23

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 23 of 36 
PART VI 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A-A,  prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, a ll electrical power sources 
and/or the external power supply. 
2. In accordance with AMP DM 69-A-64-31-04-00A-520A-A,  remove the sliding control 
assembly. 
3. Inspect the visible part of the inboard side of the TR duplex bearing (including the seals) 
for absence of wear, damages and particles by looking in side the slider cylinder. Record 
the results on Table V (refer to Figure 11). 
4. With reference to Figure 11 lock the slider of the sliding control assembly in a bench vice 
with padded jaws. 
5. Examine the duplex bearing to find roughness in accordance with the following procedure: 
NOTE 
• To initiate rotation of the duplex bearing, a 
break-out force could be necessary. The break-
out force is not an indication of roughness.  
• Relative axial movement between the inner 
races is acceptable and shall not be considered 
as a finding. 
5.1 Use your fingers to push down on the upper face of the inner race of the duplex 
bearing. 
NOTE 
Do not release pressure, continue to apply pressure 
with your fingers during the subsequent step.  
5.2 With reference to Figure 6 section A-A Step 1, push the top inner race down and 
at the same time turn it to feel if there is roughness. 
5.3 Put your finger into the duplex bearing until y ou can pull up the lower face of the 
inner race.  
NOTE 
Do not release pressure, continue to apply pressure 
with your finger during the subsequent step.  
5.4 With reference to Figure 6 section A-A Step 2, pul l the bottom inner race in the 
up direction and at the same time turn it to feel if there is roughness.  
5.5 Repeat the Step 5.1 thru Step 5.4 at least one t ime to confirm the results. 
5.6 Record the results of the previous steps on Table V  (refer to Figure 11).

### Page 24

S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 24 of 36 REVISION: B - February 4, 2020 
6. If any of the checks performed in the steps 3 and 5 fail, proceed with the following step, 
otherwise skip to step 8. 
7. Contact immediately contact the Product Support Engi neering 
(pse_aw169.mbx.aw@leonardocompany.com) to receive further instruction before 
performing the replacement of the TR duplex bearing in accordance with the following 
procedure: 
7.1 If helicopter is already compliant with the SB 169 -140, perform HUMS data 
download from AMMC to DTD. Upload the HUMS data to Heliwise. 
NOTE 
Before removal of the TR duplex bearing, take note of 
its installation orientation marking “OUT” on the 
outboard visible face. 
After removal mark “IN” on the inboard opposite face of 
the TR duplex bearing. 
Use an indelible pen. 
7.2 In accordance with AMP DM 69-A-64-31-05-00A-520A-B , remove the TR duplex 
bearing. 
7.3 Collect the grease leaked from the TR duplex bearin g “IN” marked side in a 
container different from the one used before. 
7.4 Take a picture of both faces of the removed TR dup lex bearing and send them to 
PSE (pse_aw169.mbx.aw@leonardocompany.com) before returning the bearing. 
7.5 Clean by means of a soft lint-free cloth the housin g of the TR duplex bearing, the 
rod visible part and the internal side of the spider plug. 
7.6 In accordance with AMP DM 69-A-64-31-05-00A-720A-B , install a new TR duplex 
bearing. Proceed with step 8. 
8. In accordance with AMP DM 69-A-64-31-04-00A-720A-A,  reinstall the sliding control 
assembly. 
9. With reference to Figure 3, restore the slippage m arking on the castellated nut from the 
hinge bracket element to the rod. 
10. Return the helicopter to a ready to flight condit ion and record for compliance with Part VI 
of this Service Bulletin on the helicopter logbook. 
NOTE 
In case of any findings, report within 2 days the 
inspection results along with the available records of 
the previous checks. 
11. In case replacement of the TR duplex bearing is required, please return immediately

### Page 25

S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B -  February 4, 2020 Page 25 of 36 
(within 2 days) the removed TR duplex bearing and th e collecting containers of the 
grease to Leonardo Helicopters. Contact the Product Su pport Engineering 
(pse_aw169.mbx.aw@leonardocompany.com) to receive the proper instructions to 
return the removed component. 
12. Send the attached compliance form and the compiled Table V to the following mail box:  
pse_aw169.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 26

Figure 1 
 S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 26 of 36 REVISION: B - February 4, 2020

### Page 27 (OCR)

K LEONARDO
HELICOPTERS
TRA SQUARED ROD END  SPIDER  DETAIL C  DYNAMOMETER 2  ALTERNATIVE  APPLICATION  DETAIL D  DYNAMOMETER 1  ORTHOGONAL  TO SPIDER
DYNAMOMETER 1  SPIDER
DYNAMOMETER 2  (VERTICAL POSITION)  VIEW B
DYNAMOMETER 2  VERTICAL POSITIONI
TRA SQUARED ROD END  SPIDER  DYNAMOMETER 1
Figure 2
S.B. N°169-148 EMERGENCY ALERT
DATE: May 29, 2019
REVISION: B - February 4, 2020  Page 27 of 36

### Page 28

Figure 3 
 S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 28 of 36 REVISION: B - February 4, 2020

### Page 29 (OCR)

K LEONARDO  HELICOPTERS
INSTALL:  THERMAL STRIP ON  INDICATED SPACER  DETAIL A
430A00232
THERMAL STRIP  (FOR REFERENCE ONLY)
Figure 4
S.B. N°169-148 EMERGENCY ALERT
DATE: May 29, 2019
REVISION: B - February 4, 2020  Page 29 of 36

### Page 30 (OCR)

LEONARDO
HELICOPTERS
Cutting line. Pay attention to
28  not cut the degree Celsius  scale.
16mm
Limit cutting at the minimum
TH  required to obtain 16mm of
height.
Pay attention to not damage
or to expose to the
environment the sensitive
elements.
NOTE
Do not use a thermal strip if after having trimmed it, its
sensitive element is exposed to air. See below an
example of a badly cut strip.
å
Ло  Thermal strip layers
delamination.
NOT acceptable.
Figure 5
S.B. N°169-148 EMERGENCY ALERT
DATE: May 29, 2019
Page 30 of 36  REVISION: B - February 4, 2020

### Page 31

Figure 6 
S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B - February 4, 2020 Page 31 of 36

### Page 32

Figure 7 
 S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 32 of 36 REVISION: B - February 4, 2020 
TABLE I 
 
AIRCRAFT S/N   SB COMPLIANCE DATE:  
P/N 6F6730V00331 
TRA S/N  
 
A/C FH at SB 
COMPLIANCE DATE:  
TRA FH at SB 
COMPLIANCE DATE  A/C LANDINGS at SB COMPLIANCE DATE:  
 
 
 
 
ACTION Required Obtained 
PART I 
CASTELLATED NUT 
paint mark check 
NO ROTATION BETWEEN 
PARTS

### Page 33

Figure 8 
S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B - February 4, 2020 Page 33 of 36 
TABLE II 
 
AIRCRAFT S/N   SB COMPLIANCE DATE:  
P/N 4F6430V00551 
TR DUPLEX 
BEARING S/N 
 
 
A/C FH at SB 
COMPLIANCE DATE:  
TR DUPLEX 
BEARING FH at SB 
COMPLIANCE DATE 
 A/C LANDINGS at SB COMPLIANCE DATE:  
 
ACTION Required Obtained 
PART II 
TR DUPLEX BEARING 
wear and damages check NO FINDINGS  
TR SPIDER 
axial play check 
ABSENCE of  
AXIAL PLAY  
TR DUPLEX BEARING 
roughness check 
FREE AND EASY 
ROTATION  
TR DUPLEX BEARING 
breakaway force check – Blue Arm, 
clockwise direction 
1.6 N thru 8.8 N  
TR DUPLEX BEARING  
breakaway force check – Red Arm, 
clockwise direction 
1.6 N thru 8.8 N  
TR DUPLEX BEARING 
breakaway force check – Yellow Arm, 
clockwise direction 
1.6 N thru 8.8 N  
TR DUPLEX BEARING 
breakaway force check – Blue Arm, 
counterclockwise direction 
1.6 N thru 8.8 N  
TR DUPLEX BEARING  
breakaway force check – Red Arm, 
counterclockwise direction 
1.6 N thru 8.8 N  
TR DUPLEX BEARING 
breakaway force check – Yellow Arm, 
counterclockwise direction 
1.6 N thru 8.8 N

### Page 34

Figure 9 
 S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 34 of 36 REVISION: B - February 4, 2020 
TABLE III 
 
AIRCRAFT S/N   SB COMPLIANCE DATE:  
P/N 4F6430V00551 
TR DUPLEX BEARING 
S/N 
 
 
A/C FH at SB 
COMPLIANCE DATE:  
TR DUPLEX BEARING 
FH at SB COMPLIANCE 
DATE 
 A/C LANDINGS at SB COMPLIANCE DATE:  
 
 
 
ACTION Required Obtained 
PART IV 
THERMAL STRIP 
Temperature check 
TEMPERATURE SHALL 
NOT REACH A VALUE 
EQUAL TO OR ABOVE 
121°C.

### Page 35

Figure 10 
S.B. N°169-148 EMERGENCY ALERT 
DATE: May 29, 2019 
REVISION: B - February 4, 2020 Page 35 of 36 
TABLE IV 
 
AIRCRAFT S/N   SB COMPLIANCE DATE:  
P/N 4F6430V00551 
TR DUPLEX BEARING 
S/N 
 
 
A/C FH at SB 
COMPLIANCE DATE:  
TR DUPLEX BEARING 
FH at SB COMPLIANCE 
DATE 
 A/C LANDINGS at SB COMPLIANCE DATE:  
 
 
 
ACTION Required Obtained 
PART V 
TR DUPLEX BEARING 
Particles check 
ABSENCE of ANY 
PARTICLES  
TR DUPLEX BEARING 
Grease leakage check 
ABSENCE of METALLIC 
PARTICLES

### Page 36

Figure 11 
 S.B. N°169-148 EMERGENCY ALERT 
 DATE: May 29, 2019 
Page 36 of 36 REVISION: B - February 4, 2020 
TABLE V 
 
AIRCRAFT S/N   SB COMPLIANCE DATE:  
P/N 4F6430V00551 
TR DUPLEX BEARING 
S/N 
 
 
A/C FH at SB 
COMPLIANCE DATE:  
TR DUPLEX BEARING 
FH at SB COMPLIANCE 
DATE 
 A/C LANDINGS at SB COMPLIANCE DATE:  
 
 
 
ACTION Required Obtained 
PART VI 
TR DUPLEX BEARING 
Roughness check by fingers FREE AND EASY ROTATION  
TR DUPLEX BEARING 
wear, damages and particles check on the 
inboard side of the bearing 
NO FINDINGS

### Page 37

Remarks:
Information:฀
SERVICE฀BULLETIN฀COMPLIANCE฀ ฀ ฀FORM Date:
Number:
Revision:
Please฀send฀to฀the฀following฀address:฀
Telephone:
Fax:
฀B.T.฀Compliance฀Date:
฀Customer฀Name฀and฀Address:
฀Helicopter฀Model S/N Total฀Number Total฀Hours฀ T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
