# Leonardo Service Bulletin 169-281: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2025-3986, the docket of AD 2026-17-05. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Service Bulletin 169-281](https://openairdocs.org/service-documents/leonardo/sb-169-281.md)
- Title as filed: Leonardo Helicopters SB 169-281
- Pages: 12
- PDF: https://openairdocs.org/files/sha256/f6/b2/f6b2b026e5794e0173c80e5f2711952d1ae48f64f33f38b6a6d835bf01385295
- Page: https://openairdocs.org/service-documents/leonardo/sb-169-281/file/f6b2b026e579

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Page 1 of 11 
N°  169-281 
DA TE:  November 28, 2024 
REV. :  / - December 22, 2023 
TITLE 
ATA 25 – HOIST CLUTCH REPLACEMENT 
REVISION LOG 
First Issue 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S.B. N°169-281 ALERT 
 DATE: November 28, 2024 
Page 2 of 11 REVISION: / 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
NOTE 
With reference to Figure 1 and 2, the application of the 
Service Bulletin 44314-398-01 is: 
 marked with Label ASB44314-398-01 
positioned next to the Identification Plate of 
each Hoist; 
 recorded in the Hoist Log Card and/or 
maintenance records. 
All Rescue Hoist Assemblies installed on helicopters  or kept in stock listed in Table 1 
and NOT already compliant with Onboard Systems (formerly Goodrich) Service Bulletin 
44314-398-01. 
P/N LHD 
P/N Onboard 
Systems 
S/N 
8G2591V00331 44316-10-104 40009 
8G2591V00331 44316-10-104 40056 
8G2591V00331 44316-10-104 40197 
8G2591V00331 44316-10-104 40206 
8G2591V00331 44316-10-104 40207 
6F2591V00431 44316-10-106 40208 
Table 1 
B. COMPLIANCE 
Within: 
 24 months / 1600 lifts / 1200 cycles whichever occurs first since initial 
manufacturing date or since last overload clutch replacement or 
 1 month / 66 lifts / 50 cycles whichever occurs first from the release date of this 
Service Bulletin 
whichever of the two above conditions occurs later. 
C. CONCURRENT REQUIREMENTS 
N.A.

### Page 3

S.B. N°169-281 ALERT 
DATE: November 28, 2024 
REVISION: / Page 3 of 11 
D. REASON 
Onboard Systems (formerly Goodrich) reported to Leonardo Helicopters about a batch 
of Hoist Assemblies suspected of containing overload clutch assemblies that may not 
have been assembled in accordance with the manufacturing “run-in” steps necessary 
for conditioning the internal friction disks. For this reason, Onboard Systems released 
Service Bulletin 44314-398-01 to remove the affected hoists from service in order to 
replace the suspected clutches. Service Bulletin 44314-398-01 may be performed only 
by Onboard Systems or by personnel and facilities officially trained and authorized by 
Onboard Systems. 
This Service Bulletin provides the necessary instructions to replace the affected 
Rescue Hoist Assembly and to send it to Onboard Systems for modification. 
E. DESCRIPTION 
This Service Bulletin provides the necessary instructions on how to replace the Rescue 
Hoist Assembly with a serviceable one and to send the affected one to Onboard 
Systems for modification according to Service Bulletin 44314-398-01. 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Local Aviation Authority. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin, approximately four (4) MMH are deemed 
necessary. 
MMH are based on hands-on time and can change with helicopter configuration, 
personnel and facilities available. MMH are not comprehensive of the overall hours

### Page 4

S.B. N°169-281 ALERT 
 DATE: November 28, 2024 
Page 4 of 11 REVISION: / 
necessary to get access to work areas and to remove all the equipment that interferes 
with the application of the prescribed instructions. 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
I.1 PUBLICATIONS 
Following Data Modules refer to AMP: 
DATA MODULE DESCRIPTION PART 
DM01 69-A-00-20-00-00A-120A-A Helicopter on ground for a safe 
maintenance. 
- 
DM02 69-A-06-40-00-00A-010A-A Access doors and panels - 
General data 
- 
DM03 69-A-25-71-01-02A-720A-A Hoist core (rescue hoist) - 
Install procedure 
- 
DM04 69-A-25-71-01-02A-520A-A Hoist core (rescue hoist) - 
Remove procedure 
- 
 
I.2 ACRONYMS & ABBREVIATIONS 
AMDI Aircraft Material Data Information 
AMP Aircraft Maintenance Publication 
AR As Required 
C/A Cable Assy 
CSPP Common Standard Practices Publication 
DM Data Module 
DOA Design Organization Approval 
EASA European Union Aviation Safety Agency 
IPD Illustrated Parts Data Publication 
ITEP Illustrated Tools and Equipment Publication 
LHD Leonardo Helicopters Division 
MMH Maintenance Man Hours 
N.A. Not Applicable 
P/N Part Number 
SB Service Bulletin 
S/N Serial Number 
I.3 ANNEX 
N.A.

### Page 5

S.B. N°169-281 ALERT 
DATE: November 28, 2024 
REVISION: / Page 5 of 11 
J. PUBLICATIONS AFFECTED 
N.A. 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 6

S.B. N°169-281 ALERT 
 DATE: November 28, 2024 
Page 6 of 11 REVISION: / 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
A.1 PARTS 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL  NOTE LOG P/N 
1 8G2591V00331  Hoist, core (Goodrich) AR . (1)(2) - 
2 6F2591V00431  Hoist, core (Goodrich) AR . (1)(2) - 
 
Refer also to IPD for the spares materials required to comply with the AMP DMs 
referenced in the accomplishment instructions. 
A.2 CONSUMABLES 
Refer to AMDI for the consumable materials required to comply with the AMP DMs 
referenced in the accomplishment instructions. 
A.3 LOGISTIC MATRIX 
N.A. 
NOTES 
(1) Q.ty 1 of this item is necessary to replace any affected hoist (refer to paragraph 
1.A Effectivity) either installed or kept in stock . 
(2) Please place the order directly to Onboard System. Refer to the Paragraph 2.C 
Industry Support Information of this Service Bulletin. 
B. SPECIAL TOOLS 
Refer to ITEP for the special tools required to comply with the AMP DMs referenced in 
the accomplishment instructions. 
SPECIAL TOOLS NOTES 
N.A. 
C. INDUSTRY SUPPORT INFORMATION 
A replacement of the Rescue Hoist Assembly P/N 8G2591V00331 or 
P/N 6F2591V00431 will be provided free of charge by Onboard Systems (formerly 
Goodrich) upon Customer’s request to Onboard Systems directly. 
 
Contact Onboard Systems Customer Services below: 
Onboard Systems, Hoist & Winch  
3355 E. La Palma Ave. Dock 1  
Anaheim, CA, 92806 USA

### Page 7

S.B. N°169-281 ALERT 
DATE: November 28, 2024 
REVISION: / Page 7 of 11 
E-Mail: HW-Custsupport@onboardsystems.com 
 
ONLY if Onboard Systems reject the request, please contact your Leonardo Helicopter 
CSAM sending the Vendor Ref. communication and the documents requested below:  
i. a copy of the Log Card of the inspected Rescue Hoist Assembly 
P/N 8G2591V00331 or P/N 6F2591V00431; 
ii. a copy of the EASA Form 1, FAA Form 8130-3 or any other equivalent Authorised 
Release Certificate document of the inspected Rescue Hoist Assembly. 
 
Only if confirmed by your Leonardo Helicopters’ CSAM, please Issue relevant MMIR 
form to your Warranty Administration Dpt. including the required documentation. 
If the required documentation is not provided, the relevant MMIR will be rejected. 
Owners/operators who comply with the instructions of this Service Bulletin no later than 
the applicable date in the “Compliance” section will be eligible to receive required 
materials on free of charge basis, except for Consumable Materials and Special Tools. 
NOTE: Customers who fail to comply with the instructions in this Service Bulletin before 
the compliance date are not eligible for the aforementioned special policy. 
 
NOTE: WRM will include RETURN MATERIAL AUTHORIZATION (RMA) number; the 
unit disembarked from the aircraft (Rescue Hoist Assembly P/N 8G2591V00331 or 
P/N 6F2591V00431) has to be returned to LHD within thirty (30) calendar days after the 
shipment of the replacement part. In case of missing return within thirty (30) calendar 
days, Customer will be invoiced for the price of the replacement part (Rescue Hoist 
Assembly P/N 8G2591V00331 or P/N 6F2591V00431).

### Page 8

S.B. N°169-281 ALERT 
 DATE: November 28, 2024 
Page 8 of 11 REVISION: / 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the modification 
area and adequately protect them until their later re-
use. 
b) Shape the cables in order to prevent interference 
with the structure and the other existing installations, 
using where necessary suitable lacing cords and 
plastic cable tiedown. 
c) During the installation of bonding braids or 
components requiring grounding, clean the surface 
structure in order to obtain a good ground contact. 
1. In accordance with AMP DM 69-A-00-20-00-00A-120A- A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or 
the external power supply. 
2. In accordance with AMP DM 69-A-06-40-00-00A-010A-A gain access to the area affected 
by the installation. 
3. In accordance with AMP DM 69-A-25-71-01-02A-520A-A, perform the removal of the Hoist 
Assembly. 
NOTE 
Send the affected Hoist Assembly (either removed with 
step 3 or kept in stock) to Onboard Systems for 
modification according to Service Bulletin  
44314-398-01.

### Page 9

S.B. N°169-281 ALERT 
DATE: November 28, 2024 
REVISION: / Page 9 of 11 
. 
N
OTE 
Hoist Assembly is defined as serviceable if: 
A. It is NOT listed in Table 1 
B. It is listed in Table 1 and meets one of the following 
conditions: 
B.1 It is already compliant with Service Bulletin 
44314-398-01  
B.2 It is NOT already compliant with Service Bulletin 
44314-398-01 and has NOT yet exceeded any 
of the limits detailed in paragraph 1.B 
Compliance. 
Table 1 is displayed in paragraph 1.A Effectivity. 
4. In accordance with AMP DM 69-A-25-71-01-02A-720A- A perform the installation of a 
serviceable Hoist Assembly. 
5. Return the helicopter to flight configuration and record for compliance with this Service 
Bulletin on the helicopter logbook. 
6. Gain access to My Communications section on Leonardo Customer Portal and compile 
the “Service - Technical Bulletin Application”. 
As an alternative, send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardo.com  
and (for North, Central and South America) also to: 
 AWPC.Engineering.Support@leonardocompany.us 
 
  Non cancellare mai questo segnalibro Non cancellare mai interruzione sezione 

### Page 10 (OCR)

* LEONARDO  HELICOPTERS
1.50 ‡ 0.03 inch (38.1 ‡ 0.76 mm)
0.50 ‡ 0.03 inch  ASB 44314-398-01
(12.7 ‡ 0.76 mm)  DATE:[
4X R
0.06 # 0.03 inct
(1.5 ‡ 0.76 mm)
NOTE: MAKE FROM 0.007 INCH THICK ACRYLATE (MATTE BLACK
ON WHITE) WITH ADHESIVE BACK.
[RECOMMEND MAKE FROM 3M #7847 MATTE BLACK/WHITE
ACRYLATE (STOCK # 70-0004-3110-9)]
MAY BE PRODUCED USING LASER MARKING.
NOTE: CHARACTERS ARE TO BE IN CONTRASTING COLOR.
CHARACTER HEIGHTS AND LOACTIONS TO BE
APPROXIMATELY AS SHOWN. BOX FOR DATE TO BE SOLID
FOR HAND WRITTEN DATE AT TIME OF INSTALLATION.
Figure 1
S.B. N°169-281 ALERT
DATE: November 28, 2024
Page 10 of 11  REVISION: /

### Page 11

Figure 2 
S.B. N°169-281 ALERT 
DATE: November 28, 2024 
REVISION: / Page 11 of 11

### Page 12

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
