# Leonardo Alert Service Bulletin 189-102: Revision A

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2020-0503; AD 2021-02-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 189-102](https://openairdocs.org/service-documents/leonardo/sb-189-102.md)
- Title as filed: Leonardo Helicopters ASB No 189-102 Rev A
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/ef/e1/efe1f95c28f51a7a1128a8d364123e493203a6256a18b727b5db49ebe3d71d79
- Page: https://openairdocs.org/service-documents/leonardo/sb-189-102/file/efe1f95c28f5

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N°  189-102 
DA TE:  July 15, 2016 
REV. :  A - December 21, 2017 
Pa ge 1 of 10 
TITLE
ATA 62 - MAIN ROTOR (MR) DAMPER 
REVISION LOG 
Revision A: 
The helicopters that have complied with Part I of SB189-102 Rev./ shall not comply with 
Part I of Revision A. 
Revision A is issued to allow replacement of MR damper P/N 4F6220V00251 with new MR 
damper P/N 8G6220V00151. 
Revision A also include: 
- New Service Bulletin Format 
- Instruction to return of MR damper P/N 4F6220V00251 for upgrade to 
P/N 8G6220V00151. 
Revision bars in the margins identify changes. 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S.
B. N°189-102 ALERT 
DATE: July 15, 2016 
Page 2 of 10 REVISION: A - December 21, 2017 
1. PLANNING INFORMATION
A. EFFECTIVITY 
Part I 
All AW189 helicopters equipped with MR dampers P/N 4F6220V00251. 
Part II 
All MR dampers P/N 4F6220V00251 equipped with body end P/N M006-01H002-041 
or P/N M006-01H002-047. 
B. COMPLIANCE 
NOTE 
Body end time since new or since overhaul can be 
computed based on removal/installation data recorded 
on MR damper logcard Section 2. 
Part I 
After the last flight of the day or within ten (10) flight hours after receipt of this Service 
Bulletin, whichever occurs later. 
Part II 
Within 30 flight hours from the receipt of this Service Bulletin or when MR dampers 
body end P/N M006-01H002-041 or P/N M006-01H002-047 reach 500 flight hours 
since new, whichever occurs later. 
C. CONCURRENT REQUIREMENTS 
N.A. 
D. REASON 
Initial issue 
This Service Bulletin is issued to introduce a preventive replacement of MR damper 
P/N 4F6220V00251. 
Revision A 
Revision A is issued to allow replacement of MR damper P/N 4F6220V00251 with new 
MR damper P/N 8G6220V00151. 
E. DESCRIPTION 
Part I of this Service Bulletin introduces a new lower value of MR damper locking 
tor
que installation on MR hub side and MR lever side, in order to reduce stress.

### Page 3

S.
B. N°189-102 ALERT 
DATE: July 15, 2016 
REVISION: A - December 21, 2017 Page 3 of 10 
Part II of this Service Bulletin introduces the replacement for MR dampers 
P/N 4F6220V00251, with body end that have logged 500 flight hours or more since 
new. 
Revision A is issued to allow in Part II replacement of MR damper P/N 4F6220V00251 
with new MR damper P/N 8G6220V00151. 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
nr.
 EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin. 
G. MANPOWER 
To comply with this Service Bulletin the following Maintenance-Man-Hours (MMH) are 
dee
med necessary: 
Part I: approximately ten (10) MMH. 
Part II: approximately two (2) MMH for each damper. 
Maintenance-Man-Hours are based on hands-on time and can change with personnel 
and facilities available. 
H. WEIGHT AND BALANCE 
N.A. 
I. REFERENCES 
1) PUBLICATIONS
DATA MODULE DESCRIPTION PART 
DM01 89-A-00-20-00-00A-120A-A Helicopter on ground for a safe 
maintenance. 
I,II

### Page 4

S.
B. N°189-102 ALERT 
DATE: July 15, 2016 
Page 4 of 10 REVISION: A - December 21, 2017 
DATA MODULE DESCRIPTION PART 
DM02 89-A-60-80-00-02A-913A-A Attaching parts protective layer - 
General maintenance procedure 
I 
DM03 89-A-62-22-01-00A-520A-A Outboard lightning conductor 
jumper (damper-to-lever) - 
Remove procedure 
I 
DM04 89-A-62-22-01-00A-720A-A Outboard lightning conductor 
jumper (damper-to-lever) - Install 
procedure 
I 
DM05 89-A-62-22-03-00A-520A-A Lag damper - Remove procedure  II 
DM06 89-A-62-22-03-00A-720A-A Lag damper - Install procedure II 
DM07 89-A-62-22-08-00A-520A-A Anti-rotation block - Remove 
procedure 
II 
DM08 89-A-62-22-08-00A-720A-A Anti-rotation block - Install 
procedure 
II 
2) ACRONYMS
AMP Aircraft Maintenance Publication 
DM D
ata Module 
IPD Illustrated Part Data 
MMH Maintenance Man Hour 
MR Main Rotor 
SB Service Bulletin 
3) ANNEX
N.A.
J. PUBLICATIONS AFFECTED 
AW189 Aircraft Maintenance Publication (AMP) 
AW1
89 Illustrated Part Data (IPD) 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 5

S.B. N°189-102 ALERT 
DATE: July 15, 2016 
REVISION: A - December 21, 2017 Page 5 of 10 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
PART I 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
1 MS24665-374  Cotter pin 5 .   
PART II 
NOTE 
MR damper 8G6220V00151 is fully interchangeable 
and mixable on the same MR hub with a MR damper 
P/N 4F6220V00251. If a MR damper  
P/N 8G6220V00151 is furnished to replace a damper 
P/N 4F6220V00251, also a new anti-rotation block  
P/N 8G6220A01551 must be supplied to replace the 
existing one. 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 
2 4F6220V00251  MR damper AR . (1)(2) / 
3 8G6220V00151  MR damper AR . (1)(2) / 
4 8G6220A01551  Anti-rotation block AR . (3) / 
2) CONSUMABLES 
N.
A. 
3) LOGISTIC MATRIX 
N.
A. 
NOTE 
(1) The quantity of the MR damper supplied is between 1 and 5 units depending on 
the number of damper on which the body end has reached the 500 flight hours 
and must be replaced. 
(2) Both MR dampers P/N 4F6220V00251 with body end P/N M006-01H002-047 that 
has logged less than 500 flight hours since new, and MR dampers P/N 
8G6220V00151 can be installed to comply with this SB. 
(3) This item is required when a MR damper P/N 8G6220V00151 is installed. 
 
B. SPECIAL TOOLS

### Page 6

S.
B. N°189-102 ALERT 
DATE: July 15, 2016 
Page 6 of 10 REVISION: A - December 21, 2017 
N.A. 
C. INDUSTRY SUPPORT INFORMATION 
Owners/Operators who comply with the instructions of this Bulletin, no later than the 
app
licable date in the “Compliance section” will be eligible to receive REQUIRED 
MATERIALS on free of charge basis, except for Consumable Materials & Special 
Tools. 
NOTE: Customers who fail to comply with the instructions in this bulletin before the 
compliance date are not eligible for the aforementioned special policy. 
Please Issue relevant M.M.I.R. form ( (M)aintenance (M)alfunction (I)nformation 
(R)eport ) to your Warranty Administration Dpt..

### Page 7

S.B. N°189-102 ALERT 
DATE: July 15, 2016 
REVISION: A - December 21, 2017 Page 7 of 10 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the 
modification area and adequately protect them until 
their later re-use. 
PART I 
1. In accordance with AMP DM 89-A-00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. Put the platform (GG-01-00), or an approved alternative, adjacent to the left side of the 
fuselage. 
3. In accordance with AMP DM 89-A-62-22-01-00A-520A-A, remove the outboard lightning 
conductor jumper. 
4. With reference to Figure 1, adjust the tightening torque of the nut  
P/N MS14144L10 from the bolt P/N 4F6220L00551 that fix the MR damper on the MR 
hub as follows: 
4.1 In accordance with AMP DM 89-A-60-80-00-02A-913A-A, remove the protective 
layer from the head of the bolt, the nut and the cotter pin. 
4.2 Remove the cotter pin P/N MS24665-374 from the nut and the bolt. Discard the 
cotter pin. 
4.3 Remove the nut from the bolt. Do not remove the bolt from the hub. 
4.4 Install and tighten the nut P/N MS14144L10 in accordance with the following 
procedure: 
4.4.1 Install the nut removed at step 4.3. Tighten the nut until it is possible to 
install the related cotter pin. 
4.4.2 Record the torque value at which the nut has been tightened. Make 
sure that the torque value is less than 33.89 Nm (300 lbf in). 
4.4.3 Loosen the nut and make sure that the breakaway torque value is 
more than 3.61 N m (32 lbf in). 
4.4.4 Tighten the nut to the final torque value of 74.6 thru 88 Nm (55 thru 
64.9 lbf ft) plus the installation torque value recorded at step 4.4.2. 
4.4.5 Secure the nut with a new cotter pin P/N MS24665-374. 
4.5 In accordance with AMP DM 89-A-60-80-00-02A-913A-A, apply the protective

### Page 8

S.B. N°189-102 ALERT 
 DATE: July 15, 2016 
Page 8 of 10 REVISION: A - December 21, 2017 
layer to the bolt head, the nut and the cotter pin. 
5. With reference to Figure 1, adjust the tightening torque of the nut  
P/N MS14144L10 from the bolt P/N 4F6220L00451 that fix the MR damper on the MR 
lever as follows: 
5.1 In accordance with AMP DM 89-A-60-80-00-02A-913A-A, remove the protective 
layer from the head of the bolt, the nut and the cotter pin. 
5.2 Remove the cotter pin P/N MS24665-374 from the nut and the bolt. Discard the 
cotter pin. 
5.3 Remove the nut from the bolt. Do not remove the bolt from the hub. 
5.4 Install and tighten the nut P/N MS14144L10 in accordance with the following 
procedure: 
5.4.1 Install the nut removed at step 5.3. Tighten the nut until it is possible to 
install the related cotter pin. 
5.4.2 Record the torque value at which the nut has been tightened. Make 
sure that the torque value is less than 33.89 Nm (300 lbf in). 
5.4.3 Loosen the nut and make sure that the breakaway torque value is 
more than 3.61 N m (32 lbf in). 
5.4.4 Tighten the nut to the final torque value of 74.6 thru 88 Nm (55 thru 
64.9 lbf ft) plus the installation torque value recorded at step 5.4.2. 
5.4.5 Secure the nut with a new cotter pin P/N MS24665-374. 
5.5 In accordance with AMP DM 89-A-60-80-00-02A-913A-A, apply the protective 
layer to the bolt head, the nut and the cotter pin 
6. In accordance with AMP DM 89-A-62-22-01-00A-720A-A, install the outboard lightning 
conductor jumper. 
7. Repeat steps 3 thru 6 until you have changed nut torque on all the MR dampers. 
8. Remove the platform (GG-01-00) from the left side of the fuselage. 
9. Return the helicopter to flight configuration and record for compliance with Part I of this 
Service Bulletin on the helicopter logbook. 
10. Send the attached compliance form to the following mail box: 
 pse_aw189.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 9

S.B. N°189-102 ALERT 
DATE: July 15, 2016 
REVISION: A - December 21, 2017 Page 9 of 10 
PART II 
1. In accordance with AMP DM 89-A-00-20-00-00A-120A-A, prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. Identify the MR dampers that install body end P/N M006-01H002-041 or  
P/N M006-01H002-047 having logged 500 flight hours. 
3. In accordance with AMP DM 89-A-62-22-03-00A-520A-A, remove the MR dampers  
P/N 4F6220V00251 previously identified. 
4. Send the removed MR dampers to Leonardo Helicopter customer support. Please refer 
to your usual contact point in LHD Material Services, in order to arrange the return of 
replaced items in LHD facility. 
NOTE 
MR damper 8G6220V00151 is fully interchangeable 
and mixable on the same MR hub with a MR damper 
P/N 4F6220V00251. If a MR damper  
P/N 8G6220V00151 is furnished to replace a damper 
P/N 4F6220V00251, also a new anti-rotation block  
P/N 8G6220A01551 must be supplied to replace the 
existing one. 
5. In accordance with AMP DM 89-A-62-22-03-00A-720A- A, install the replacement MR 
dampers as required. 
6. If a MR damper P/N 8G6220V00151 will be installed, in accordance with AMP  
DM 89-A-62-22-08-00A-520A-A and DM 89-A-62-22-08-00A-720A-A, replace the anti-
rotation block with a new one P/N 8G6220A01551. 
7. Return the helicopter to flight configuration and record for compliance with Part II of this 
Service Bulletin on the helicopter logbook. 
8. Send the attached compliance form to the following mail box: 
 pse_aw189.mbx.aw@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”. 
 
  Non cancellare mai questo segnalibro Non cancellare mai interruzione sezione 

### Page 10

Figure 1 
 S.B. N°189-102 
 DATE: July 15, 2016 
Page 10 of 10 REVISION: A - December 21, 2017

### Page 11

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
