# Leonardo Service Bulletin 189-254: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-0612, the docket of AD 2021-20-17. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Service Bulletin 189-254](https://openairdocs.org/service-documents/leonardo/sb-189-254.md)
- Title as filed: Leonardo Helicopters SB No. 189-254
- Pages: 17
- PDF: https://openairdocs.org/files/sha256/ff/f8/fff82b3e89af07ab68acf0d0617c8a5f743ff7be15f85551bf8e80b8b1c2631a
- Page: https://openairdocs.org/service-documents/leonardo/sb-189-254/file/fff82b3e89af

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ERRATA CORRIGE 
 
 
Please find here attached the pages that have to be replaced in the basic Service Bulletin 
n°189-254 
 
 PAGE 4 “PUBLICATION” section 
 
Was: 
DATA MODULE DESCRIPTION PART 
DM01 89-A-00-20-00-00A-120A-A Helicopter on ground for a safe 
maintenance. 
All 
DM02 89-A-64-11-05-00A-520A-A Lightning conductor jumper - 
Remove procedure 
All 
Becomes: 
DATA MODULE DESCRIPTION PART 
DM01 89-A-00-20-00-00A-120A-A Helicopter on ground for a safe 
maintenance. 
All 
DM02 DELETED - - 
 
 PAGE 8 “ACCOMPLISHMENT INSTRUCTIONS” 
 
Was: 
Step 6  - In accordance with AMP DM 89-A-64-11-05-00A-520A-A, disconnect the 
TR lightning conductor jumper. 
Becomes: 
Step 6  - DELETED. 
 
 PAGE 11 “ACCOMPLISHMENT INSTRUCTIONS” 
  
Was: 
Step 6  - In accordance with AMP DM 89-A-64-11-05-00A-520A-A, disconnect the 
TR lightning conductor jumper. 
Becomes: 
Step 6  - DELETED.

### Page 2

N°  189-254
DA TE:  August 4, 2020 
REV. :  / -     
Pa ge 1 of 15 
TITLE 
ATA 64 - TAIL ROTOR IMPROVED DUPLEX BEARING INSTALLATION 
REVISION LOG 
First Issue 
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
SERVICE BULLETIN

### Page 3

S.B. N°189-254 
 DATE: August 4, 2020 
Page 2 of 15 REVISION: / 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
Part I: All AW189 helicopters equipped with Tail Rotor Duplex Bearing 
P/N 4F6430V00551. 
Part II: All AW189 helicopters already equipped with Tail Rotor Duplex Bearing 
P/N MM6430V00151. 
B. COMPLIANCE 
Part I:  
Within than 400 flight hours or 4 months whichever occurs first from the issue of this 
Service Bulletin. 
 
Part II:  
NOTES 
A non-cumulative tolerance of 10% may be applied to 
the compliance times specified below to allow 
synchronization of the required inspections with other 
required maintenance tasks for which a non-cumulative 
tolerance is already granted in the applicable 
Maintenance Manual. 
Within 400 FH accumulated by the Duplex Bearing PN M M6430V00151 installed on 
AW189 helicopter. 
C. CONCURRENT REQUIREMENTS 
Refer also to SB 189-272 for additional operations needed upon any installation of 
improved Tail Rotor Duplex Bearing P/N MM6430V00151. 
D. REASON 
This Service Bulletin is issued in order to provide the necessary instruction on how to 
perform the installation of the new Tail Rotor Duplex Bearing P/N MM6430V00151 in 
lieu of P/N 4F6430V00551.

### Page 4

S.B. N°189-254 
DATE: August 4, 2020 
REVISION: / Page 3 of 15 
E. DESCRIPTION 
Leonardo Helicopters Division has developed this Service Bulletin in order to require the 
installation of the new Tail Rotor Duplex Bearing P/N MM6430V00151 in lieu of 
P/N 4F6430V00551 on AW189 helicopters. 
The new Tail Rotor Duplex Bearing features material changes for different internal 
components and general optimization of the internal micro geometry, aimed to reduce 
the heat generation. 
Part I of this Service Bulletin provides the necessary instructions on how to install the 
new Tail Rotor Duplex Bearing P/N MM6430V00151 in lieu of P/N 4F6430V00551. 
Part II of this Service Bulletin requires any new Tail Rotor Duplex Bearing 
P/N MM6430V00151 to be replaced with a brand new unit everytime the component 
reaches a certain amount of FH.  
The removed bearings, not to be scrapped, must be promptly returned to LHD. 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA nr. 
EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin.  
G. MANPOWER 
To comply with this Service Bulletin the following MMH are deemed necessary: 
Part I: approximately ten (10) MMH 
Part II: approximately ten (10) MMH 
MMH are based on hands-on time and can change with personnel and facilities 
available. 
H. WEIGHT AND BALANCE 
N.A.

### Page 5

S.B. N°189-254 
 DATE: August 4, 2020 
Page 4 of 15 REVISION: / 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE DESCRIPTION PART 
DM01 89-A-00-20-00-00A-120A-A Helicopter on ground for a 
safe maintenance. 
All 
DM02 DELETED - - 
DM03 89-A-64-31-01-00A-520A-A Pitch link -  
Remove procedure 
All 
DM04 89-A-64-31-01-00A-720A-A Pitch link -  
Install procedure 
All 
DM05 89-A-64-31-02-00A-520A-A Scissors group -  
Remove procedure 
All 
DM06 89-A-64-31-03-00A-520A-A Spider plug -  
Remove procedure 
All 
DM07 89-A-64-31-03-00A-720A-A Spider plug -  
Install procedure 
All 
DM08 89-A-64-31-04-00A-720A-A Spider and slider assembly - 
Install procedure 
All 
DM09 89-A-64-31-05-00A-520A-B Duplex Bearing -  
Remove procedure 
All 
DM10 89-A-64-31-05-00A-720A-B Duplex Bearing -  
Install procedure 
All 
DM11 89-A-64-31-07-00A-520A-A Boot - Remove procedure All 
2) ACRONYMS 
AMDI Aircraft Material Data Information 
AMP Aircraft Maintenance Publication 
AR As Required 
CSRP Common Structural Repair Publication 
DM Data Module 
DOA Design Organization Approval 
EASA European Aviation Safety Agency 
IPD Illustrated Parts Data 
ITEP Illustrated Tool and Equipment Publication 
LHD Leonardo Helicopters Division 
MLG Main Landing Gear 
MMH Maintenance-Man-Hours

### Page 6

S.B. N°189-254 
DATE: August 4, 2020 
REVISION: / Page 5 of 15 
3) ANNEX 
N.A. 
J. PUBLICATIONS AFFECTED 
AW189 Aircraft Maintenance Publication (AMP) 
AW189 Illustrated Part Data (IPD) 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 7

S.B. N°189-254 
 DATE: August 4, 2020 
Page 6 of 15 REVISION: / 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
PART I 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL  NOTE LOG P/N 
1 8G6400P00111  
REWORK, TAIL ROTOR 
CONTROLS 
INSTALLATION 
REF .  - 
2 MM6430A00151  Spacer 1 ..  - 
3 8G6430P00331  SLIDING CONTROL ASSY REWORK REF ..  - 
4 MM6430V00151  Tail rotor duplex bearing 1 …  189-254L1 
5 4F6430A01451  Peeling shim 1 …  189-254L1 
6 LAMHALPATCH01R1  Protective layer REF .. (1) 189-254L1 
7 M06SHA094D01R1  Thermal strip REF .. (1)(2) 189-254L1 
8 MS24665-136  Pin 4 .  189-254L1 
9 MS24665-374  Pin 1 .  189-254L1 
10 MS24665-302  Pin 4 .  189-254L1 
11 MS24665-155  Pin 6 .  189-254L1 
12 MS24665-86  Pin 6 .  189-254L1 
13 A864A0356E006T  Peeling Shim 6 .  189-254L1 
14 AW001CK07HS  Strap Tiedown 2 .  189-254L1 
PART II 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL  NOTE LOG P/N 
15 MM6430V00151  Tail rotor duplex bearing 1 .  189-254L1 
16 4F6430A01451  Peeling shim 1 .  189-254L1 
17 LAMHALPATCH01R1  Protective layer REF . (1) 189-254L1 
18 M06SHA094D01R1  Thermal strip REF . (1)(2) 189-254L1 
19 MS24665-136  Pin 4 .  189-254L1 
20 MS24665-374  Pin 1 .  189-254L1 
21 MS24665-302  Pin 4 .  189-254L1 
22 MS24665-155  Pin 6 .  189-254L1 
23 MS24665-86  Pin 6 .  189-254L1 
24 A864A0356E006T  Peeling Shim 6 .  189-254L1 
25 AW001CK07HS  Strap Tiedown 2 .  189-254L1 
Refer also to IPD for the consumable materials required to comply with the AMP DM 
referenced in the accomplishment instructions 
2) CONSUMABLES 
Refer also to AMDI for the consumable materials required to comply with the AMP 
DM referenced in the accomplishment instructions.

### Page 8

S.B. N°189-254 
DATE: August 4, 2020 
REVISION: / Page 7 of 15 
3) LOGISTIC MATRIX 
In order to apply this Service Bulletin, the following Logistic P/N can be ordered in 
accordance with the applicable notes: 
 
LOGISTIC P/N Q.TY (PER HELO) NOTE PART 
189-254L1 1 (3) 1,2 
MM6430A00151 1 - 1 
NOTES 
(1) Item required in Q.ty within Part III of SB 189-272. 
(2) Identification on label M06SHAL094D01R1 is printed on the thermal strip. 
(3) Logistic P/N is firstly required upon accomplishment of Part I. It shall be made newly 
available for Part II embodiment in accordance with the relevant compliance. 
B. SPECIAL TOOLS 
# P/N DESCRIPTION Q.TY NOTE PART 
26 8G6430G00131 Tool, T/R pitch control link adjust 1 (1) / 
27 8G6420G01832 T/R spider & slider, remove/installation tool kit 1 (1) / 
28 8G6430G03331 TR duplex bearing  removal-installation tool kit 1 (1) / 
 
Refer also to ITEP for the special tools required to comply with the AMP DM referenced 
in the accomplishment instructions. 
 
(1)If the present tool is not already owned in Customer’s stock, please contact Leonardo 
Helicopters order administration point of contact to request the tool supply on loan. As 
soon as the present Service Bulletin is implemented the tool supplied on loan shall be 
promptly returned to Leonardo Helicopters. 
C. INDUSTRY SUPPORT INFORMATION 
Owners/Operators who comply with the instructions of this Service Bulletin no later than 
the applicable date in the “Compliance” section will be eligible to receive necessary 
replacements on free of charge basis, except for Consumable Materials and Special 
Tools.  
NOTE: Customers who fail to comply with the instructions in this Service Bulletin before 
the compliance date are not eligible for the aforementioned special policy.  
Please Issue relevant MMIR form to your Warranty Administration Dpt.  
NOTE: WRM will include RETURN MATERIAL AUTHORIZATION (RMA) number; the 
unit removed from the aircraft has to be returned to LHD as per instructions defined into 
LHD Information Letter GEN-15-047 and GEN-19-075.

### Page 9

S.B. N°189-254 
 DATE: August 4, 2020 
Page 8 of 15 REVISION: / 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the modification 
area and adequately protect them until their later re-
use. 
b) Exposed thread surface and nut must be protected 
using a layer of tectyl according to MIL-C-16173 
grade I. 
c) All lengths are in mm. 
PART I 
1. In accordance with DM 89-A-00-20-00-00A-120A-A, prepare the helicopter on ground for 
a safe maintenance. Disconnect the battery, all electrical power sources and/or the 
external power supply. 
2. In accordance with AMP DM 89-A-64-31-03-00A-520A-A, remove the spider plug. 
3. In accordance with applicable steps of AMP DM 89-A-64-31-01-00A-520A-A, temporarily 
detach the upper attachment of all the pitch links from the TR. 
4. In accordance with applicable steps of AMP DM 89-A-64-31-02-00A-520A-A, disconnect 
the upper half scissors from the spider. 
5. In accordance with applicable steps of AMP DM 89-A-64-31-07-00A-520A-A, disconnect 
and lower the boot from the spider. 
6. DELETED. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
NOTE 
Before removal of the TR duplex bearing, take note of 
its installation orientation marking “OUT” on the 
outboard visible face. After removal mark “IN” on the 
inboard opposite face of the TR duplex bearing. Use an 
indelible pen. 
7. In accordance with AMP DM 89-A-64-31-05-00A-520A- B, remove Tail Rotor Duplex 
Bearing P/N 4F6430V00551.

### Page 10

S.B. N°189-254 
DATE: August 4, 2020 
REVISION: / Page 9 of 15 
8. Return the Tail Rotor Duplex Bearing P/N 4F6430V00551 removed within step 7 to 
Leonardo Helicopters Customer Support within 2 days. Please refer to your usual contact 
point in Leonardo Helicopters Material Services, in order to arrange the return of replaced 
items in LHD facility. 
CAUTION 
Duplex Bearing must be installed with a controlled 
orientation. 
9. In accordance with AMP DM 89-A-64-31-05-00A-720A- B, install Tail Rotor Duplex Bearing 
P/N MM6430V00151, keeping the outer race outside marking properly readable while 
letting down in the slider/spider seat. Refer to Figure 1. 
10. With reference to Figure 2, mark Retromod P/N 8G6430P00331 on the Sliding Control 
assembly P/N 4F6430A01332 by method of vibro-etching. 
11. In accordance with the instructions reported on Part III of SB 189-272, install new Thermal 
Strip and Adhesive Protective Layer on Spacer P/N MM6430A00151.  
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end.  
NOTES 
In case during the installation of control rod nut, after 
several attempts with different nuts, the minimum 
required breakaway torque (as required by AMP DM 89-
A-64-31-04-00A-720A-A) is not reached, please contact 
the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) to 
receive dedicated instructions. 
12. In accordance with AMP DM 89-A-64-31-04-00A-720A -A, install new Spacer 
P/N MM6430A00151 and reinstall Sliding Control Assy on the helicopter. 
13. Restore the slippage marking on the castellated nut from the hinge bracket element to the 
rod. 
14. In accordance with AMP DM 89-A-64-31-01-00A-720A-A, restore the correct installation 
of TR pitch links. It is possible to re-protect TR pitch links and the scissors using the 
following procedure: 
14.1 Clean the bolts by means of cleaning solvent. 
14.2 Check the bolts looking for corrosion. Contact the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) in case of any findings.

### Page 11

S.B. N°189-254 
 DATE: August 4, 2020 
Page 10 of 15 REVISION: / 
14.3 Protect the parts using Tectyl Grade I or Thixoflex Black as a valid alternative. 
15. In accordance with AMP DM 89-A-64-31-03-00A-720A-A, install the spider plug. 
16. Return the helicopter to flight configuration and record for compliance with Part I of this 
Service Bulletin on the helicopter logbook. 
17. Send the attached compliance form to the following mail box:         
engineering.support.lhd@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal and 
compile the “Service Bulletin Application Communication”.

### Page 12

S.B. N°189-254 
DATE: August 4, 2020 
REVISION: / Page 11 of 15 
PART II 
1. In accordance with AMP DM 89-A-00-20-00-00A-120A-A prepare the helicopter on ground 
for a safe maintenance. Disconnect the battery, all electrical power sources and/or the 
external power supply. 
2. In accordance with AMP DM 89-A-64-31-03-00A-520A-A, remove the spider plug. 
3. In accordance with applicable steps of AMP DM 89-A-64-31-01-00A-520A-A, temporarily 
detach the upper attachment of all the pitch links from the TR. 
4. In accordance with applicable steps of AMP DM 89-A-64-31-02-00A-520A-A, disconnect 
the upper half scissors from the spider. 
5. In accordance with applicable steps of AMP DM 89-A-64-31-07-00A-520A-A, disconnect 
and lower the boot from the spider. 
6. DELETED. 
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end. 
NOTE 
Before removal of the TR duplex bearing, take note of 
its installation orientation marking “OUT” on the 
outboard visible face. After removal mark “IN” on the 
inboard opposite face of the TR duplex bearing. Use an 
indelible pen. 
7. In accordance with AMP DM 89-A-64-31-05-00A-520A- B, remove Tail Rotor Duplex 
Bearing P/N MM6430V00151 installed on helicopter. Record on the applicable logcard 
that the component was removed as required by Part II of SB 189-254. 
8. Return the removed Tail Rotor Duplex Bearing P/N MM6430V00151 to Leonardo 
Helicopters Customer Support within 2 days, also shipping all the documentation relevant 
to the component, such as logcard and SB compliance forms. Please refer to your usual 
contact point in Leonardo Helicopters Material Services, in order to arrange the return of 
replaced items in LHD facility. 
CAUTION 
Duplex Bearing must be installed with a controlled 
orientation. 
9. In accordance with AMP DM 89-A-64-31-05-00A-720A- B, install Tail Rotor Duplex Bearing 
P/N MM6430V00151, keeping the outer race outside marking properly readable while 
letting down in the slider/spider seat. Refer to Figure 1.

### Page 13

S.B. N°189-254 
 DATE: August 4, 2020 
Page 12 of 15 REVISION: / 
NOTE 
Spacer P/N MM6430A00151 already installed on 
helicopter can be kept in service, provided that no 
damage or wear is present on the component. 
10. In accordance with the instructions reported on Part III of SB 189-272, replace Thermal 
Strip and Adhesive Protective Layer currently installed on Spacer P/N MM6430A00151.  
CAUTION 
Pay attention to prevent rod rotation, when screwing / 
un-screwing the castellated nut, holding the rod square 
end.  
NOTE 
In case during the installation of control rod nut, after 
several attempts with different nuts, the minimum 
required breakaway torque (as required by AMP DM 89-
A-64-31-04-00A-720A-A) is not reached, please contact 
the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) to 
receive dedicated instructions. 
11. In accordance with AMP DM 89-A-64-31-04-00A-720A -A, restore Sliding Control Assy 
installation on the helicopter. 
12. Restore the slippage marking on the castellated nut from the hinge bracket element to the 
rod. 
13. In accordance with AMP DM 89-A-64-31-01-00A-720A-A, restore the correct installation 
of TR pitch links. It is possible to re-protect TR pitch links and the scissors using the 
following procedure: 
13.1 Clean the bolts by means of cleaning solvent. 
13.2 Check the bolts looking for corrosion. Contact the Product Support Engineering 
(engineering.support.lhd@leonardocompany.com) in case of any findings. 
13.3 Protect the parts using Tectyl Grade I or Thixoflex Black as a valid alternative. 
14. In accordance with AMP DM 89-A-64-31-03-00A-720A-A, install the spider plug. 
15. Return the helicopter to flight configuration and record for compliance with Part II of this 
Service Bulletin on the helicopter logbook and on the logcard of the Duplex Bearing 
removed as per step 7.

### Page 14

S.B. N°189-254 
DATE: August 4, 2020 
REVISION: / Page 13 of 15 
16. Send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal and 
compile the “Service Bulletin Application Communication”. 
 Non cancellare mai questo segnalibro   Non cancellare mai interruzione sezione 

### Page 15

Figure 1 
 S.B. N°189-254  
 DATE: August 4, 2020 
Page 14 of 15 REVISION: / 
 
 
SB189-254-001-01
4F6430A01332 SLIDING CONTROL ASSEMBL Y
MM6430V00151 TAIL ROTOR DUPLEX BEARING

### Page 16

Figure 2 
S.B. N°189-254  
DATE: August 4, 2020 
REVISION: / Page 15 of 15 
 
 
4F6430A01332 SLIDING CONTROL ASSEMBLY
SB189-254-002-01
MARK RETROMOD P/N 8G6430P00331 
8G6430P00331

### Page 17

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
