# Leonardo Alert Service Bulletin 189-265: No revision named

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-1060, the docket of AD 2021-25-08. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Leonardo Alert Service Bulletin 189-265](https://openairdocs.org/service-documents/leonardo/sb-189-265.md)
- Title as filed: Leonardo Helicopters ASB No. 189-265 Rev 0
- Pages: 23
- PDF: https://openairdocs.org/files/sha256/4e/22/4e221b5f703855b39496526d7f63dd04327022ea9cb3cae395bdf7f798692112
- Page: https://openairdocs.org/service-documents/leonardo/sb-189-265/file/4e221b5f7038

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

N°  189-265
DA TE:  March 4, 2021 
REV. :  / -  
Pa ge 1 of 22 
TITLE 
ATA 33 – MR TIP LIGHTS FAIRING RETROMOD 
REVISION LOG 
First Issue 
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
SERVICE BULLETIN

### Page 2

S.B. N°189-265 ALERT 
 DATE: March 4, 2021 
Page 2 of 22 REVISION: / 
1. PLANNING INFORMATION 
A. EFFECTIVITY 
Part I 
AW189 equipped with MR tip lights kit P/N 8G3340F00411 and: 
 FIPS kit P/N 8G3000F00111 
or 
  LIPS kit P/N 8G3000F00211 or P/N 8G3000F00212 
not already compliant with Part II of this SB. 
Part II 
AW189 helicopters equipped with MR tip lights kit P/N 8G3340F00411 and: 
 FIPS kit P/N 8G3000F00111 
or 
 LIPS kit P/N 8G3000F00211 or P/N 8G3000F00212. 
NOTE 
The installation of the fairings P/N 8G3340A12531 and 
P/N 8G3340A12631 (parts of the MR tip lights kit 
P/N 8G3340F00411) present at stock is prohibited 
from the date of issuance of this Service Bulletin. 
 
B. COMPLIANCE 
NOTE 
The installation mandated in Part I shall not be 
removed, while flying in known icing conditions, until 
Part II is accomplished. 
Part I 
Before the next flight in icing condition from the receipt of this Service Bulletin. 
Part II: 
Within 400 FH or 1 year whichever occurs first from receipt of this Service Bulletin. 
 
C. CONCURRENT REQUIREMENTS 
N.A.

### Page 3

S.B. N°189-265 ALERT 
DATE: March 4, 2021 
REVISION: / Page 3 of 22 
D. REASON 
This Service Bulletin is issued to require the Rescue Hoist Kit to be present during all 
the flights in known icing conditions for the helicopters installing the MR tip lights kit 
P/N 8G3340F00411 until this kit is modified through the installation of MR tip light 
fairing retromod P/N 8G3340P02411. 
E. DESCRIPTION 
A potential issue has been discovered affecting the LH and RH fairings 
P/N 8G3340A12531 and P/N 8G3340A12631 (parts of the MR tip lights kit 
P/N 8G3340F00411) in case they are installed during flights in icing conditions. The 
following investigation identified the installation of the hoist equipment as a mandatory 
mitigating action to fly in icing condition until the fairings are replaced with a new 
design. To address this potentially unsafe condition, LHD issue this Service Bulletin to 
require to check that the hoist equipment is always installed before every flight in 
known icing condition, on all the helicopters equipped with MR tip lights kit 
P/N 8G3340F00411 and either FIPS or LIPS kits (Part I), until the installation of the 
retromod P/N 8G3340P02411 (Part II).  
The retromod introduces three new fairings to replace the FWD, RH and LH fairings of 
the MR tip lights Kit P/N 8G3340F00411. The installation of three bonding strips is 
required to complete the MR tip light fairing retromod. After installation of this 
retromod, the MR tip lights installation can be considered equivalent to MR tip lights kit 
P/N 8G3340F02111 that is applicable to helicopters equipped with FIPS of LIPS kit. 
F. APPROVAL 
The technical content of this Service Bulletin is approved under the authority of DOA 
nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before 
applying the Service Bulletin, applicable Aviation Authority approval must be checked 
within Leonardo Helicopters customer portal. 
EASA states mandatory compliance with inspections, modifications or technical 
directives and related time of compliance by means of relevant Airworthiness 
Directives. 
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified 
and affecting the content of this Service Bulletin, it is responsibility of the 
Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on 
the aircraft, for any adaptation necessary before incorporation of the present Service 
Bulletin.

### Page 4

S.B. N°189-265 ALERT 
 DATE: March 4, 2021 
Page 4 of 22 REVISION: / 
G. MANPOWER 
To comply with this Service Bulletin the following Maintenance-Man-Hours (MMH) are 
deemed necessary: 
Part I: approximately two (2) MMH 
Part II: approximately forty (40) MMH 
MMH are based on hands-on time and can change with personnel and facilities 
available. 
H. WEIGHT AND BALANCE 
PART I 
Refer to the applicable AW189 helicopter Chart A - Equipment list already provided 
and referenced to in the AW189 RFM, Section 6. 
PART II 
Rotor tip light equipment installation P/N 8G3340A02811 
WEIGHT (Kg) 2.267 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 3857.9 8747.5 
LATERAL BALANCE -69.7 -158.0 
 
Rotor tip light for IPS complete provision P/N 8G3340A06511 
WEIGHT (Kg) 1.714 
 ARM (mm) MOMENT (Kgmm) 
LONGITUDINAL BALANCE 3881.6 6653.1 
LATERAL BALANCE -74.0 -126.9 
I. REFERENCES 
1) PUBLICATIONS 
DATA MODULE DESCRIPTION PART 
DM01 89-A-00-20-00-00A-120A-A Helicopter on ground for a safe 
maintenance 
I, II 
DM02 89-A-16-11-00-05A-028A-A  Role change procedures - 
Double rescue hoist system kit - 
General 
I 
DM03 89-A-33-61-01-00A-520A-A Forward light - Remove 
procedure 
II

### Page 5

S.B. N°189-265 ALERT 
DATE: March 4, 2021 
REVISION: / Page 5 of 22 
DATA MODULE DESCRIPTION PART 
DM04 89-A-33-61-01-00A-720A-A Forward light - Install procedure II 
DM05 89-A-33-61-02-00A-520A-A Forward light fairing - Remove 
procedure 
II 
DM06 89-A-33-61-05-00A-520A-A Right light - Remove procedure II 
DM07 89-A-33-61-05-00A-720A-A Right light - Install procedure II 
DM08 89-A-33-61-06-00A-520A-A Right light fairing - Remove 
procedure 
II 
DM09 89-A-33-61-03-00A-520A-A Left light - Remove procedure II 
DM10 89-A-33-61-03-00A-720A-A Left light - Install procedure II 
DM11 89-A-33-61-04-00A-520A-A Left light fairing - Remove 
procedure 
II 
DM12 CSRP-A-51-22-02-00A-258A-D Preparation of composite 
bonding surfaces - Other 
procedure to clean 
II 
DM13 CSRP-A-51-22-01-00A-258A-D Preparation of metallic bonding 
surfaces - Other procedure to 
clean 
II 
DM14 CSRP-A-51-21-02-02A-257A-D Waterborne chromate free primer 
(AWMS28-002) - Paint and apply 
marking 
II 
DM15 CSRP-A-51-21-01-02A-257A-D Polyurethane paint (MIL-PRF-
85285) - Paint and apply marking 
II 
DM16 CSRP-A-51-21-06-00A-644A-D Chromate conversion treatments 
of alluminium alloys - Chromate 
II 
DM17 89-A-20-00-04-00A-921A-A Gasket tape - Replacement 
(remove and install a new item) 
II 
DM18 89-A-20-00-07-00A-921A-A Conductive gasket tape - 
Replacement (remove and install 
a new item) 
II 
DM19 CSRP-A-51-43-02-00A-921A-D Adhesive bonded anchor nuts - 
Replacement (remove and install 
a new item) 
II 
2) ACRONYMS 
AMDI Aircraft Material Data Information 
AMP Aircraft Maintenance Publication 
AR As Required 
CSRP Common Structural Repair Publication 
DM Data Module 
DOA Design Organization Approval 
EASA European Aviation Safety Agency

### Page 6

S.B. N°189-265 ALERT 
 DATE: March 4, 2021 
Page 6 of 22 REVISION: / 
FH Flight Hours 
FWD Forward 
IPD Illustrated Part Data 
LH Left Hand 
LHD Leonardo Helicopters Division 
MMH Maintenance-Man-Hours 
MR Main Rotor 
RH Right Hand 
3) ANNEX 
N.A. 
J. PUBLICATIONS AFFECTED 
AW189 Aircraft Maintenance Publication (AMP) 
AW189 Illustrated Part Data (IPD) 
K. SOFTWARE ACCOMPLISHMENT SUMMARY 
N.A.

### Page 7

S.B. N°189-265 ALERT 
DATE: March 4, 2021 
REVISION: / Page 7 of 22 
2. MATERIAL INFORMATION 
A. REQUIRED MATERIALS 
1) PARTS 
PART I 
N.A. 
PART II 
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL  NOTE LOG P/N 
1 8G3340P02411  
MAIN ROTOR ILLUMTN 
LIGHTS 
RETRO MOD 
REF .   
2 8G3340A12432  Fairing assy FWD 1 ..  189-265L1 
3 8G3340A12532  Fairing assy LHS 1 ..  189-265L1 
4 8G3340A12632  Fairing assy RHS 1 ..  189-265L1 
5 8G3340A29951 8G3340A29951A Bonding strip 1 ..  189-265L1 
6 8G3340A07651 8G3340A07651A Bonding strip 2 ..  189-265L1 
7 A297A05TW03  Rivet 8 ..  189-265L1 
8 A297A05TW04  Rivet 2 ..  189-265L1 
9 A407A3C2 A407A3C2P Anchor nut 14 ..  189-265L1 
10 AN525-10R16  Screw 4 ..  189-265L1 
11 MS27039-1-05  Screw 6 ..  189-265L1 
12 MS27039-1-09  Screw 28 ..  189-265L1 
13 MS27039-1-10  Screw 4 ..  189-265L1 
14 NAS1149D0316K  Washer 38 ..  189-265L1 
2) CONSUMABLES 
The following consumable materials, or equivalent, are necessary to accomplish this 
Service Bulletin: 
# Spec./LHD code number DESCRIPTION Q.TY NOTE PART  
15 Commercial Sealant PR1764 Class B2 (C240) AR (1) II 
16 Commercial Sealant 2200 AR (1)(2) II 
17 AWMS05-001, Type I, Class B, 
Grade 2 Code No. 
999999999000005965 or 
999999999000015245 
Sealing compound MC 780 B-2 (C465) 
AR 
(1) II 
18 Commercial Paint AR (1) II 
19 DTD 900AA/4488A Corrosion preventive compound JC5A 
(C001) AR (1) II 
20 WHPS083 Type A  
Code No. 999999999000017311 
Corrosion preventive compound Cor-Ban 
27L (C075) AR (1)(3) II 
21 TT-I-735, Grade A Isopropyl alcohol (C039) AR (1) II 
22 Commercial Lint-free cloth AR (1) II 
23 Commercial Sealant Thixoflex Gray AR (1) II 
24 AWMS28-002, Type I, Class 1, 
Grade A or B 
Epoxy primer (C596) AR (1) II 
25 MIL-DTL-81706, Class 1A & 3,  
Form II 
Conversion coating Alodine 1200 (C237) AR (1) II 
26 199-05-002 Type I Class 2  
Code No. 900000581 
Adhesive EA9309.3NA (C021) AR (1) II

### Page 8

S.B. N°189-265 ALERT 
 DATE: March 4, 2021 
Page 8 of 22 REVISION: / 
Refer also to AMDI for the consumable materials required to comply with the AMP 
DM referenced in the accomplishment instructions. 
3) LOGISTIC MATRIX 
In order to apply this Service Bulletin, the following Logistic P/N can be ordered in 
accordance with the applicable notes: 
LOGISTIC P/N Q.TY (PER HELO) NOTE PART 
189-265L1 1 - II 
NOTE 
(1) Item to be procured as local supply. 
(2) May be used as alternative to Sealant PR1764 Class B2 (C240). 
(3) May be used as alternative to Corrosion preventive compound JC5A (C001). 
B. SPECIAL TOOLS 
N.A. 
C. INDUSTRY SUPPORT INFORMATION 
WARRANTY: Owners/Operators who comply with the instructions of this Service 
Bulletin no later than the applicable date in the “Compliance” section will be eligible to 
receive required materials on free of charge basis, except for Consumable Materials 
and Special Tools.  
NOTE: Customers who fail to comply with the instructions in this Service Bulletin 
before the compliance date are not eligible for the aforementioned special policy.  
Please Issue relevant MMIR form to your Warranty Administration Dpt.

### Page 9

S.B. N°189-265 ALERT 
DATE: March 4, 2021 
REVISION: / Page 9 of 22 
3. ACCOMPLISHMENT INSTRUCTIONS 
GENERAL NOTES 
a) Place an identification tag on all components that 
are re-usable, including the attaching hardware that 
has been removed to gain access to the 
modification area and adequately protect them until 
their later re-use. 
b) Exercise extreme care during drilling operations to 
prevent instruments, cables and hoses damage. 
c) After drilling, remove all swarf and sharp edges. 
Apply on bare metal a light film of primer unless the 
hole is used for ground connection. 
d) Protect properly all those equipment not removed 
from area affected by the modification during 
installation procedure. 
e) Let the adhesive cure at room temperature for at 
least 24 hours, unless otherwise specified. 
f) All lengths are in mm. 
PART I 
1. In accordance with AMP DM 89-A-00-20-00-00A-120A-A prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. Make sure that the helicopter is equipped with the removable parts P/N 8G2591A08311 
of the rescue hoist kit P/N 8G2591F00311. If the helicopter is equipped with this kit, skip 
to Step 4. 
3. In accordance with AMP DM 89-A-16-11-00-05A-028A-A, install the rescue hoist kit 
P/N 8G2591F00311. 
4. Return the helicopter to flight configuration and record for compliance with Part I of this 
Service Bulletin on the helicopter logbook. 
5. Send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”.

### Page 10

S.B. N°189-265 ALERT 
 DATE: March 4, 2021 
Page 10 of 22 REVISION: / 
PART II 
1. In accordance with AMP DM 89-A-00-20-00-00A-120A-A prepare the helicopter on 
ground for a safe maintenance. Disconnect the battery, all electrical power sources 
and/or the external power supply. 
2. With reference to Figures 1 thru 4, perform the installation of the “main rotor illumination 
light retromod” P/N 8G3340P02411 as described in the following procedure: 
CAUTION 
Be careful when you pull the light P/N LFD/286/001. If 
you are not careful you can cause damage to the 
electrical cable. 
2.1 In accordance with AMP DM 89-A-33-61-01-00A-520A -A and with reference to 
Figure 1 Detail A, remove the forward MR tip light P/N LFD/286/001 from the 
fairing assy FWD P/N 8G3340A12431. 
2.2 In accordance with AMP DM 89-A-33-61-02-00A-520A-A and with reference to 
Figure 1 Detail A, remove the fairing assy FWD P/N 8G3340A12431 from the LH 
canopy panel. Retain existing hardware for later reuse. 
NOTE 
The following Steps 2.3 and 2.4 are not applicable to 
helicopters already compliant with SB 189-126. 
CAUTION 
Take care not to damage the composite canopy or 
aluminium upper deck roof panel. 
2.3 With reference to Figure 1 Detail A, remove the existing copper bonding strip 
P/N 8G3340A13151 and n°2 rivets P/N A297A05 from the LH canopy panel and 
the upper deck roof panel. 
2.4 With reference to Figure 1, install the bonding strip P/N 8G3340A29951 on the 
LH canopy panel and the upper deck roof panel as described in the following 
procedure: 
2.4.1 With reference to Figure 1 Schematic Detail A, temporarily locate the 
bonding strip P/N 8G3340A29951 on the structure; countermark the 
edges on the LH canopy panel and the upper deck roof panel.

### Page 11

S.B. N°189-265 ALERT 
DATE: March 4, 2021 
REVISION: / Page 11 of 22 
CAUTION 
Ensure the all surfaces and holes are free from residue 
of previously applied adhesive and paint. 
2.4.2 In accordance with CSRP DM CSRP-A-51-22-02-00A -258A-D and with 
reference to Figure 1 Schematic Detail A, prepare the indicated area 
on the LH canopy panel surface for bonding. 
2.4.3 In accordance with CSRP DM CSRP-A-51-22-01-00A-258A-D and with 
reference to Figure 1 Schematic Detail A, prepare the indicated area 
on the upper deck roof panel for bonding. 
2.4.4 With reference to Figure 1 Detail A, install the bonding strip 
P/N 8G3340A29951 to the LH canopy panel by means of adhesive 
EA9309NA (C021) and to the upper deck roof panel by means of 
conductive sealant PR1764 B2 (C240). 
NOTE 
Prior to re-installing fasteners to be used as electrical 
bonding contact points, ensure that internal bore of the 
hole is free from paint, varnish and grease. 
NOTE 
Dip the rivets in the conductive sealant PR1764 B2 
(C240) before installation. 
2.4.5 With reference to Figure 1 Detail A, install n °2 rivets 
P/N A297A05TW04 to the bonding strip P/N 8G3340A29951 and the 
structure. 
2.4.6 In accordance with CSRP DM CSRP-A-51-21-02-02A-257A-D and with 
reference to Figure 1 Detail A, apply the epoxy primer (C596) on the 
LH canopy panel around the bonding strip P/N 8G3340A29951, where 
exposed surfaces remain. 
NOTE 
Ensure to apply sealant within the gap between upper 
deck roof panel and the LH canopy panel. 
2.4.7 With reference to Figure 1 Detail A, apply the  sealant MC 780 B-2 
(C465) all around the bonding strip P/N 8G3340A29951. 
2.4.8 In accordance with CSRP DM CSRP-A-51-21-01-02A-257A-D and with 
reference to Figure 1 Detail A, apply two coats of Polyurethane paint 
on the bonding strip P/N 8G3340A29951 in accordance with the 
helicopter paint scheme.

### Page 12

S.B. N°189-265 ALERT 
 DATE: March 4, 2021 
Page 12 of 22 REVISION: / 
2.5 With reference to Figures 1 and 4, install the fairing assy FWD 
P/N 8G3340A12432 on the LH canopy panel as described in the following 
procedure: 
2.5.1 With reference to Figure 1 Schematic Detail A, temporarily locate the 
fairing assy P/N 8G3340A12432 FWD on the structure, countermark 
the edges on the bonding strip P/N 8G3340A29951 and the LH canopy 
panel. 
2.5.2 With reference to Figure 1 Schematic Detail A, prepare the indicated 
area on the bonding strip P/N 8G3340A29951 for good electrical 
bonding. 
2.5.3 In accordance with CSRP DM CSRP-A-51-21-06-00A-644A-D and with 
reference to Figure 1 Schematic Detail A, protect the indicated area on 
the bonding strip P/N 8G3340A29951 by means of conversion coating 
(C597). 
NOTE 
HT3000 sealant tape must not be torn or damaged and 
must not have excessive squeeze out of the gel layer 
which is sandwiched between the self-adhesive side 
and the top layer of the tape. If excessive squeeze out 
has occurred then there will no longer be any 
compression in the tape when squeezing in between 
your fingers. 
2.5.4 In accordance with applicable steps of AMP DM  
89-A-20-00-04-00A-921A-A and with reference to Figure 4 View C, 
install HT3000 sealant tape on the fairing assy FWD 
P/N 8G3340A12432. 
2.5.5 In accordance with applicable steps of AMP DM  
89-A-20-00-07-00A-921A-A and with reference to Figure 4, install the 
conductive gasket P/N AW001GH on the fairing assy FWD 
P/N 8G3340A12432.

### Page 13

S.B. N°189-265 ALERT 
DATE: March 4, 2021 
REVISION: / Page 13 of 22 
NOTE 
Surfaces that will come into contact with the sealing 
tape shall be free of paint, dust, oil, grease, fingerprints 
and other contaminations prior to installation. The 
surfaces shall be wiped with a clean, solvent 
dampened cloth using isopropyl alcohol (C039) or MEK 
(C005), followed immediately by wiping with a clean 
dry cloth (C011). Residue of previously applied 
adhesives, sealants, or fillet sealing materials shall be 
removed. 
NOTE 
Wet install all fairing fasteners using compound JC5A 
(C001) or compound Cor-Ban 27L (C075), ensuring to 
apply the sealant on the fastener shank and 
underneath the fastener head. 
2.5.6 With reference to Figure 1 Detail A, install t he fairing assy FWD 
P/N 8G3340A12432 on the LH canopy panel by means of n°4 screws 
P/N AN525-10R16, n°6 screws P/N MS27039-1-05, n°4 screws 
P/N MS27039-1-10 and n°10 washers P/N NAS1149D0316K. 
2.5.7 With reference to Figure 1 Detail A, seal the fairing assy FWD 
P/N 8G3340A12432 all around by means of sealant Thixoflex Gray or 
sealant (C617). 
2.6 With reference to Figure 1 Detail A, perform the electrical bonding test between 
the fairing assy FWD P/N 8G3340A12432 (point 1) and the upper deck roof panel 
(point 2) using a multimeter. Make sure that the bonding value is less than 2.5 
mΩ. 
2.7 In accordance with AMP DM 89-A-33-61-01-00A-720A-A and with reference to 
Figure 1 Detail A install the forward MR tip light P/N LFD/286/001 on the fairing 
assy FWD P/N 8G3340A12432. 
CAUTION 
Be careful when you pull the light P/N LFD/286/001. If 
you are not careful you can cause damage to the 
electrical cable. 
2.8 In accordance with AMP DM 89-A-33-61-03-00A-520A -A and with reference to 
Figure 2 Detail B Was, remove the LH MR tip light P/N LFD/286/001 from the 
fairing assy LH P/N 8G3340A12531.

### Page 14

S.B. N°189-265 ALERT 
 DATE: March 4, 2021 
Page 14 of 22 REVISION: / 
2.9 In accordance with AMP DM 89-A-33-61-02-00A-520A-A and with reference to 
Figure 2 Detail B Was, remove the fairing assy LH P/N 8G3340A12531 from the 
LH sidewall panel and the existing hardware. 
CAUTION 
Take care not to damage the composite sidewall or 
aluminium upper deck roof panel. 
2.10 With reference to Figure 2 Detail B Was, remove  the existing copper bonding 
strip P/N 8G3340A13251 and n°4 existing rivets from the LH sidewall panel and 
the upper deck roof panel. 
2.11 With reference to Figures 2 thru 3, install the bonding strip P/N 8G3340A07651 
on the LH sidewall panel and the upper deck roof panel as described in the 
following procedure: 
2.11.1 With reference to Figure 2 Schematic Detail B, temporarily locate the 
bonding strip P/N 8G3340A07651 on the structure; countermark the 
edges on the LH sidewall panel and the upper deck roof panel. 
CAUTION 
Ensure the all surfaces and holes are free from residue 
of previously applied adhesive and paint. 
2.11.2 In accordance with CSRP DM CSRP-A-51-22-02-00 A-258A-D and with 
reference to Figure 2 Schematic Detail B, prepare the indicated area 
on the LH sidewall panel for bonding. 
2.11.3 In accordance with CSRP DM CSRP-A-51-22-01-00A-258A-D and with 
reference to Figure 2 Schematic Detail B, prepare the indicated area 
on the upper deck roof panel for bonding. 
2.11.4 With reference to Figure 3 Detail B Becomes, install the bonding strip 
P/N 8G3340A07651 to the LH sidewall panel by means of adhesive 
EA9309NA (C021) and to the upper deck roof panel by means of 
conductive sealant PR1764 B2 (C240).

### Page 15

S.B. N°189-265 ALERT 
DATE: March 4, 2021 
REVISION: / Page 15 of 22 
NOTE 
Prior to re-installing fasteners to be used as electrical 
bonding contact points, ensure that internal bore of the 
hole is free from paint, varnish and grease. 
NOTE 
Dip the rivets in the sealant PR1764 B2 (C240) before 
installation. 
2.11.5 With reference to Figure 3 Detail B Becomes, install n°2 rivets 
P/N A297A05TW03 to the bonding strip P/N 8G3340A07651 and the 
structure. 
2.11.6 With reference to Figure 3 Detail B Becomes, install n° 2 rivets 
P/N A297A05TW03 on the LH sidewall panel and upper deck roof 
panel. 
2.11.7 In accordance with CSRP DM CSRP-A-51-21-02-02A-257A-D and with 
reference to Figure 3 Detail B Becomes, apply the epoxy primer (C596) 
on the LH sidewall panel around the bonding strip P/N 8G3340A07651 
where exposed surfaces remain. 
NOTE 
Ensure to apply sealant within the gap between upper 
deck roof panel and the sidewall panel. 
2.11.8 With reference to 3 Detail B Becomes, apply t he sealant (C465) all 
around the bonding strip P/N 8G3340A07651. 
2.11.9 In accordance with CSRP DM CSRP-A-51-21-01-02A-257A-D and with 
reference to Figure 3 Detail B Becomes, apply two coats of 
Polyurethane paint on the bonding strip P/N 8G3340A07651 in 
accordance with helicopter paint scheme. 
2.12 With reference to Figures 3 thru 4, install the fairing assy LH P/N 8G3340A12532 
on the LH sidewall panel as described in the following procedure: 
2.12.1 With reference to Figure 2 Schematic Detail B, temporarily locate the 
fairing assy LH P/N 8G3340A12532 on the structure, countermark the 
edges on the bonding strip P/N 8G3340A07651 and the edges and the 
holes on the LH sidewall panel. 
2.12.2 In accordance with applicable steps of CSRP  
DM CSRP-A-51-43-02-00A-921A-D and with reference to Figure 3 
Detail B Becomes, drill n°7 holes Ø6.20÷6.35 thru the LH sidewall 
panel.

### Page 16

S.B. N°189-265 ALERT 
 DATE: March 4, 2021 
Page 16 of 22 REVISION: / 
2.12.3 In accordance with applicable steps of CSRP  
DM CSRP-A-51-43-02-00A-921A-D and with reference to Figure 3 
Detail B Internal View, install n°7 anchor nut P/N A407A3C2 on the LH 
sidewall panel by means of Adhesive EA9309.3NA (C021). 
2.12.4 With reference to Figure 2 Schematic Detail B, prepare the indicated 
area on the bonding strip P/N 8G3340A07651 for good electrical 
bonding. 
2.12.5 In accordance with CSRP DM CSRP-A-51-21-06-00A-644A-D and with 
reference to Figure 2 Schematic Detail B, protect the indicated area on 
the bonding strip P/N 8G3340A07651 by means of Chemical 
conversion coating (C597). 
NOTE 
HT3000 sealant tape must not be torn or damaged and 
must not have excessive squeeze out of the gel layer 
which is sandwiched between the self-adhesive side 
and the top layer of the tape. If excessive squeeze out 
has occurred then there will no longer be any 
compression in the tape when squeezing in between 
your fingers. 
2.12.6 In accordance with applicable steps of AMP DM  89-A-20-00-04-00A-
921A-A and with reference to Figure 4 View D, install HT3000 sealant 
tape on the fairing assy LH P/N 8G3340A12532. 
2.12.7 In accordance with applicable steps of AMP DM 89-A-20-00-07-00A-
921A-A and with reference to Figure 4 View D, replace the conductive 
gasket P/N AW001GH on the fairing assy LH P/N 8G3340A12532.

### Page 17

S.B. N°189-265 ALERT 
DATE: March 4, 2021 
REVISION: / Page 17 of 22 
NOTE 
Surfaces that will come into contact with the sealing 
tape shall be free of paint, dust, oil, grease, fingerprints 
and other contaminations prior to installation. The 
surfaces shall be wiped with a clean, solvent 
dampened cloth using isopropyl alcohol (C039) or mek 
(C005), followed immediately by wiping with a clean 
dry cloth (C011). Residue of previously applied 
adhesives, sealants, or fillet sealing materials shall be 
removed. 
NOTE 
Wet install all fairing fasteners using compound JC5A 
(C001) or compound Cor-Ban 27L (C075), ensuring to 
apply the sealant on the fastener shank and 
underneath the fastener head. 
2.12.8 With reference to Figure 3 Detail B Becomes, install the fairing assy 
P/N 8G3340A12532 on the LH sidewall panel by means of n°14 
screws P/N MS27039-1-09 and n°14 washers P/N NAS1149D0316K. 
2.12.9 With reference to Figure 3 Detail B Becomes, seal the fairing assy LH 
P/N 8G3340A12532 all around by means of sealant Thixoflex Gray or 
sealant (C617). 
2.13 With reference to Figure 3 Detail B Becomes, perform the electrical bonding test 
between the fairing assy LH P/N 8G3340A12532 (point 3) and the upper deck 
roof panel (point 4) using a multimeter. Make sure that the bonding value is less 
than 2.5 mΩ. 
2.14 In accordance with AMP DM 89-A-33-61-03-00A-720A-A and with reference to 
Figure 3 detail B Becomes, install the LH MR tip light P/N LFD/286/001 on the 
fairing assy LH P/N 8G3340A12532. 
CAUTION 
Be careful when you pull the light P/N LFD/286/001. If 
you are not careful you can cause damage to the 
electrical cable. 
2.15 In accordance with AMP DM 89-A-33-61-05-00A-520 A-A and with reference to 
Figure 2 Detail B Was, remove the RH MR tip light P/N LFD/286/001 from the 
fairing assy RH P/N 8G3340A12631.

### Page 18

S.B. N°189-265 ALERT 
 DATE: March 4, 2021 
Page 18 of 22 REVISION: / 
2.16 In accordance with AMP DM 89-A-33-61-06-00A-520A-A and with reference to 
Figure 2 Detail B Was, remove the fairing assy RH P/N 8G3340A12631 from the 
RH sidewall panel and the existing hardware. 
CAUTION 
Take care not to damage the composite sidewall or 
aluminium upper deck roof panel. 
2.17 With reference to Figure 2 Detail B Was, remove  the existing copper bonding 
strip P/N 8G3340A13251F002 and n°4 existing rivets from the RH sidewall panel 
and the upper deck roof panel. 
2.18 With reference to Figures 2, repeat steps 2.11.1 thru 2.11.9 to install the bonding 
strip P/N 8G3340A07651 on the RH sidewall panel and the upper deck roof 
panel. 
2.19 With reference to Figures 3 thru 4, repeat steps 2.12.1 thru 2.12.9 to install the 
fairing assy RH P/N 8G3340A12632 on the RH sidewall panel. 
2.20 With reference to Figures 3 Detail B Becomes, repeat the step 2.13 to perform 
the bonding test between the fairing assy RH P/N 8G3340A12632 and the upper 
deck roof panel. 
2.21 In accordance with AMP DM 89-A-33-61-05-00A-720A-A, install the right MR tip 
light P/N LFD/286/001 on the fairing assy RH P/N 8G3340A12632. 
3. In accordance with weight and balance changes, update the Chart A (see Rotorcraft 
Flight Manual, Part II, section 6). Mark new MR tip lights kit P/N 8G3340F02111 and 
remove existing entry for MR tip lights kit P/N 8G3340F00411. 
4. Return the helicopter to flight configuration and record for compliance with this Service 
Bulletin on the helicopter logbook. 
5. Send the attached compliance form to the following mail box: 
 engineering.support.lhd@leonardocompany.com 
As an alternative, gain access to My Communications section on Leonardo WebPortal 
and compile the “Service Bulletin Application Communication”. 
 Non cancellare mai questo segnalibro   Non cancellare mai interruzione sezione 

### Page 19 (OCR)

LEONARDO
HELICOPTERS
MAIN ROTOR ILLUMINATION LIGHTS RETROMOD
UPPER DECK ROOF PANEL (REF
8G3340P02411  REMOVE:
8G3340A13151 BONDING STRIP
INSTALL:
8G3340A29951 BONDING STRIP
APPLY:
EA9309.3NA ADHESIVE
SEALANT PR1764 B2
POLYURETHANE PAINT
DETAIL A
REMOVE
EXISTING RIVET
INSTALL:
DETAIL B  A297A05TW04 RIVET.
(TYP 2 PLCS)
(SEE FIGURE 2-3)
/1
APPLY:
MC780 B2 SEALANT
APPLY:  ALL AROUND
SEALANT THIXOFLEX GRA
ALL AROUND
REMOVE:
LH SIDE ISOVIEW  MS27039-1-05  NAS1149D0316K WASHER  SCREW
INSTALL:
MS27039-1-05  SCREW
NAS1149D0316K WASHER
REMOVE:  C  APPLY:  COMPOUND JC5A
525-10R16 SCREW
(SEE FIGURE 4)  (TYP 6 PLCS)
N525-10R16 SCREW
COMPOUND JC5A  LH CANOPY PANEL (REF)
(TYP 4 PLCS)
LFD/286/001 MR TIP LIGHT (REF)
REMOVE:
8G3340A12431 FAIRING ASSY FWD
NSTALL:
8G3340A12432 FAIRING ASSY FWD  DETAIL A
STRUCTURE AND SYSTEMS ARE PARTIALLY OMITTED FOR BETTER CLARITY PURPOSE
S27039-1-10  SCREW
AS1149D0316K WASHER
182/039-1-10  SCREW  UPPER DECK ROOF PANEL (REF)  UPPER DECK ROOF PANEL (REF)  BONDING AREA
S1149D0316K WASHER  ACCORDING TO
8G3340A29951 BONDING STRIP
COMPOUND JC5A
(TYP 4 PLCS)
8G3340A29951 BONDING STRIP (REF)
BONDING AREA
ACCORDING TO
8G3340A12431 FAIRING ASSY FWD
8G3340A29951 BONDING STRIP (REF)
APPLY:  LA CANOPY PANEL (REF)
ALODINE 1200
LH CANOPY PANEL (REF)  BONDING AREA
ACCORDING TO
8G3340A29951 BONDING STRIP
LH CANOPY PANEL (REF)
BONDING AREA
ACCORDING TO
8G3340A12431 FAIRING ASSY FWD
APPLY EPOXY PRIMER
ON UNPAINTED SURFACE AROUND THE BONDING STRIP
ELECTRICAL BONDING TEST POINT  SCHEMATIC DETAIL A
Figure 1
S.B. N°189-265 ALERT
DATE: March 4, 2021
REVISION: /  Page 19 of 22

### Page 20 (OCR)

LEONARDO
HELICOPTERS
UPPER DECK ROOF PANEL (REF  REMOVE:
MS27039-1-09 SCREW
NAS1149D0316K WASHER
(TYP 10 PLCS)
REMOVE:
8G3340A13251F001 BONDING STRIP
8G3340A13251F002 BONDING STRIP
EXISTING RIVET
LFD/286/001 MR TIP LIGHT (REF)  UP
REMOVE:
8G3340A12531 FAIRING ASSY LH
8G3340A12631 FAIRING ASSY RH
LH
FWD
LH/RH SIDEWALL PANEL (REF)
DETAIL B WAS
STRUCTURE AND SYSTEMS ARE PARTIALLY OMITTED FOR BETTER CLARITY PURPOSE
UPPER DECK ROOF PANEL (REF)  LH SHOWN
(RH OPPOSITE)
(REFER TO FIGURE 1)
UPPER DECK ROOF PANEL (REF)
BONDING AREA
ACCORDING TO  8G3340A07651 BONDING STRIP (REF)
8G3340A07651 BONDING STRIP  BONDING AREA
ACCORDING TO
8G3340A12431 FAIRING ASSY FWD
8G3340A07651 BONDING STRIP (REF)
APPLY:
ALODINE 1200
LH/RH SIDEWALL PANEL (REF)
BONDING AREA
ACCORDING TO
8G3340A07651 BONDING STRIP
LH/RH SIDEWALL PANEL (REF)
BONDING AREA
CCORDING TO
G3340A12532 FAIRING ASSY LH
8G3340A12632 FAIRING ASSY RH
LH/RH SIDEWALL PANEL (REF)
SCHEMATIC DETAIL B
LH SHOWN
(RH OPPOSITE)
(REFER TO FIGURE 1)
Figure 2
S.B. N°189-265 ALERT
DATE: March 4, 2021
Page 20 of 22  REVISION: /

### Page 21 (OCR)

: LEONARDO
HELICOPTERS
W03 RIVET (QTY 2)°
UPPER DECK ROOF PANEL  G3340A07651 BONDING STRIF
297A05TW03 RIVET (QTY 2
A9309.3NA ADHESIVE
POLYURETHANE PAINT
86/001 MR TIP LIGHT (REF)
3340A12532 FAIRING ASSY LF
8G3340A12632 FAIRING ASSY RH
(SEE FIGURE 4)
INSTALL:  UP
MS27039-1-09 SCREW
NAS1149D0316K WASHER
APPLY:
COMPOUND JC5A
(TYP 14 PLCS)
LH/RH SIDEWALL PANEL (REF)  • LH
FWD
DETAIL B BECOMES
STRUCTURE AND SYSTEMS ARE PARTIALLY OMITTED FOR BETTER CLARITY PURPOSE
LH SHOWN
(RH OPPOSITE)  UPPER DECK ROOF PANEL (REF)
(REFER TO FIGURE 1)
INSTALL:
A407A3C2 ANCHOR NUT °
CONDING T
BG3340A12532 FAIRING ASSY LF
8G3340A12632 FAIRING ASSY RH
APPLY:
EA9309.3NA ADHESIVE
(TYP 7 PLCS)
D
(SEE FIGURE 4)
LH/RH SIDEWALL PANEL (REF)
UP
FWD
DETAIL B INTERNAL VIEW
STRUCTURE AND SYSTEMS ARE PARTIALLY OMITTED FOR BETTER CLARITY PURPOSE
LH SHOWN  APPLY EPOXY PRIMER
(RH OPPOSITE)  ON UNPAINTED SURFACE AROUND THE BONDING STRIP
(REFER TO FIGURE 1)  ELECTRICAL BONDING TEST POINT
(4)  LH SHOWN (RH OPPOSITE)
Figure 3
S.B. N°189-265 ALERT
DATE: March 4, 2021
REVISION: /  Page 21 of 22

### Page 22 (OCR)

K LEONARDO  HELICOPTERS
AW001GH
CONDUCTIVE GASKET (REF
HT3000 SEALANT TAPE (REF)
VIEW C
8G3340A12432 FAIRING ASSY FWD
(REFER TO FIGURE 1)
HT3000 SEALANT TAPE (REF)
\W001GH
CONDUCTIVE GASKET (REF
VIEW D
8G3340A12532 FAIRING ASSY LH
8G3340A12632 FAIRING ASSY RH
LH SHOWN
(RH OPPOSITE)
(REFER TO FIGURE 3)
Figure 4
S.B. N°189-265 ALERT
DATE: March 4, 2021
Page 22 of 22  REVISION: /

### Page 23

Remarks:
Information: 
SERVICE BULLETIN COMPLIANCE   FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
