# Finmeccanica Alert Bollettino Tecnico 412-146: Revision A

- Rights: © Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2017-1077; AD 2021-07-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Finmeccanica Alert Bollettino Tecnico 412-146](https://openairdocs.org/service-documents/leonardo/sb-412-146.md)
- Title as filed: Finmeccanica Helicopter Division Alert BT 412-146 Revision A
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/ab/ff/abffe373bfe03f8d621ab8ca1784da22c7888889d244e6fd07108b530fe2177c
- Page: https://openairdocs.org/service-documents/leonardo/sb-412-146/file/abffe373bfe0

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Page 1 of 10 
BOLLETTINO TECNICO 
The technical content of this document is approved 
under the authority of DOA nr. EASA.21J.005. 
N°     412-146 
DATE      July 06, 2016
REV. A  July 07, 2016 
Comp
liance with 
this bulletin is: 
SUBJECT: INSPECTION OF THE SPIRAL BEVEL GEAR P/N 204-040-701 -103 OF 
THE MAIN TRANSMISSION. 
REASON:  Introduction of additional inspections of spiral bevel gear P/N 204-040-701-103. 
HELICOPTERS AFFECTED: 
PARTI I: 
AB412 helicopters up to S/N 25669. 
PART II:
 
AB412 helicopters up to S/N 25669 that install the spiral bevel gear P/N 204-040-701 -103 
with serial numbers included in Table 1. 
SPIRAL BEVEL GEAR S/N SPIRAL BEVEL GEAR S/N SPIRAL BEVEL GEAR S/N 
A0616 A2 0648 C45371 
A0617 A2 0650 C45372 
A0618 A2 0651 C45373 
A0619 A2 0652 C45374 
A0620 A2 0653 C45375 
A0621 A2 0659 C45376 
A0624 A2 0660 C45377 
A0628 A2 0661 C45378 
A0629 B27327 C45379 
A0631 B27329 E28464 
A0635 B27330 E28465 
A0637 B27333 B27326 
A2 0644 B27337 B27335 
A2 0646 C45369 
A2 0647 C45370 
Table 1 
MANDATORY
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Finmeccanica S.p.A.
Via Giovanni Agusta, 520
21017 Cascina Costa di Samarate (VA) Italy
Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
ALERT
ALERT

### Page 2

B.T. 412-146 
Page 2 of 10 
COMPLIANCE: 
PART I: 
Within the next 10 flight hours after the issue of this Bollettino. 
PART II: 
For the affected spiral bevel gear P/N 204-040 -701-103 that have accumulated 1.200 FH or 
more, within the next 100  flight hours after accomplishment of PART I, and subsequently 
every 300 flight hours. 
For the affected spiral bevel gear P/N 204-040-701 -103 that have less of 1.200 FH at the 
reaching of 1.200 FH and subsequently every 300 flight hours. 
DESCRIPTION: 
During accomplishment of a main transmission P/N 212-040 -001-59 overhaul, a crack on 
spiral bevel gear P/N 204-040-701-103 was found. 
The preliminary investigations show that the crack was originated from the bottom of one of 
32 threaded holes and that other spiral bevel gears manufactured with the same process could 
be subject to a similar event.  This Bollettino therefore requires an unscheduled inspection of 
the spiral bevel gear P/N 204-040 -701-103 installed on AB412 helicopters in order to detect 
the parts with serial numbers identified in Table 1 and, for the affected parts, a repetitive 
inspection for cracks. 
The revision A is issued to update the list of spiral bevel gear serial numbers (Table 1) and to 
define the warranty policy. 
MANPOWER REQUIRED: 
PART I: Approximately 2 man-hours are required to complete Part I of this Bollettino. 
PART II: Approximately 32 man-hours are required to complete Part II of this Bollettino. 
This estimate is based on hands-on time, and may vary with personnel and facilities available.

### Page 3

B.T. 412-146
Page 3 of 10 
WARRANTY:   
Owners/Operators who comply with the instructions of this Bollettino, according to the 
“Compliance section” will be eligible to receive REQUIRED MATERIALS on free of charge 
basis, except for Consumable Materials and Special Tools. 
NOTE: Customers who fail to comply with the instructions in this Bollettino before the 
compliance number of Flight Hours are not eligible for the aforementioned special policy. 
Please Issue relevant M.M.I.R. form ( (M)aintenance (M)alfunction (I)nformation (R)eport ) to 
your Warranty Administration Dpt. 
MATERIAL REQUIRED: 
PART I: 
The following material is required for the accomplishment of this Bollettino. 
PART II: 
N.A. 
SPECIAL TOOLS:   
Endoscope IPLEX MXII - IV8415M or equivalent. 
T100929 Jackscrew or equivalent. 
WEIGHT AND BALANCE CHANGE: 
N.A. 
REFERENCES: 
AB412-IPC Illustrated Parts Catalogue 
AB412-MM Maintenance Manual 
BHT-ALL-SPM  Standard Practice Manual 
BHT-412-CR&O  Component Repair and Overhaul Manual 
PUBBLICATIONS AFFECTED: 
AB412-MPM Maintenance Planning Manual 
P/N DENOMINATION Q.TY 
MS29561-248 O-Ring 1

### Page 4

B.T. 412-146 
Page 4 of 10 
ACCOMPLISHMENT INSTRUCTIONS: 
PART I: 
1. Prepare the helicopter for safe ground maintenance, disconnect battery and all the electric
power source and/or the external power supply.
2. Gain access to transmission area (RH side) removing forward pylon fairing and RH
transmission fairing in accordance with AB412-MM.
3. Gain access to RH transmission quill port cover removing RH pylon bulkhead door as
indicate in Figure 1 and in accordance with AB412-MM.
4. Remove the transmission quill port cover (ref. Figure 1) in accordance with AB412 -MM
Chapter 63-26.
5. Insert the endoscope in the transmission as shown in Figure 2. Place the endoscope to the
top of the transmission.
6. To find the serial number on the spiral bevel gear rotate slowly the tail rotor blades until the
serial number appears on the screen. The serial number is marked on the edge of the spiral
bevel gear as shown in Figure 2  and in Figure 3a. As alternate, the serial number could be
located as shown in Figure 3b.
NOTE 
Each spiral bevel gear is marked with the part number, with the 
FHD Manufacturer Code A0126 and with the serial number. 
7. Record the spiral bevel gear part number and serial number in the applicable Main
Transmission documents.
8. If the serial number identified is not included in Table 1, no further actions are required
proceed in accordance with step 13.
9. If the serial number is included in Table 1, mark one tooth of the spiral bevel gear with
white chalk (or equivalent) as shown in Figure 4.
10. With the aid of a light source, by rotating the tail rotor blades, visually inspect the teeth of
the spiral bevel gear for presence of cracks.
11. If cracks are found, remove the spiral bevel gear from service and replace it with an
airworthy spiral bevel gear. Report inspection findings to FHD Product Support Engineering
at the following e-mail address absereng.AW@leonardocompany.com
12. If cracks are not found, proceed in accordance with the following steps.
13. Re-install the transmission quill port cover in accordance with AB412-MM Chapter 63-26.
14. Re-install the RH pylon bulkhead door in accordance with AB412-MM.

### Page 5

B.T. 412-146
Page 5 of 10 
15. Re-install the forward pylon fairing and RH transmission fairing in accordance with AB412-
MM.
16. Return the helicopter to a ready to flight condition.
17. Record compliance with PART I of  th is Bollettino in the applicable Main Transmission
documents.
PART II 
1. Prepare the helicopter for safe ground maintenance, disconnect battery and all the electric
power source and/or the external power supply.
2. In accordance with AB412-MM Chapter 63-22 remove the transmission from the helicopter.
3. Remove the spiral bevel gear P/N 204-040 -701-103 from transmission (ref. BHT-412-CR&O
Chapter 63-00) and perform Fluorescent Magnetic Particle Inspection (ASTM-E-1444) i n
accordance with BHT-412-CR&O Table 63-3 and BHT-ALL-SPM Chapter 6-00 para. 6-17 .
(Refer to Figure 5 and Figure 6 for typical crack found during inspection).
4. If after inspection cracks are found, remove the spiral bevel gear from service and replace it
with an airworthy spiral bevel gear. Report inspection findings to FHD Product Support
Engineering at the following e-mail address absereng.AW@leonardocompany.com
5. If after inspection no cracks are found, reinstall spiral bevel gear P/N 204-040 -701-103 and
re-assembly the transmission in accordance with BHT-412-CR&O Chapter 63-00.
6. In accordance with AB412-MM Chapter 63-22 re-install the transmission on the helicopter.
7. Return the helicopter to a ready to flight condition.
8. Record compliance with PART II of  this Bollettino in the applicable Main Transmission
documents.

### Page 6

B.T. 412-146 
Page 6 of 10 
Figure 1 – View from RH pylon bulkhead door 
QUILL PORT COVER

### Page 7

B.T. 412-146
Page 7 of 10 
Figure 2 
S/N SPIRAL BEVEL GEAR

### Page 8

B.T. 412-146 
Page 8 of 10 
Figure 3a 
Figure 3b 
ALTERNATIVE 
S/N LOCATION 
S/N LOCATION 
(see Detail A) 
Detail A - Edge of spiral bevel gear

### Page 9

B.T. 412-146 
Page 9 of 10 
 
 
 
 
 
 
 
 
 
Figure 4    
  
MARKING OF  ONE TOOTH 
OF THE SPIRAL BEVEL 
GEAR WITH A WHITE 
CHALK

### Page 10

B.T. 412-146 
Page 10 of 10 
Figure 5 – Crack on spiral bevel gear P/N 204-040-701-103 
Figure 6 – Crack on spiral bevel gear P/N 204-040-701-103

### Page 11

Remarks:
Information: 
 BOLLETTINO TECNICO COMPLIANCE FORM Date:
Number:
Revision:
Please send to the following address: 
Telephone:
Fax:
 B.T. Compliance Date:
 Customer Name and Address:
 Helicopter Model S/N Total Number Total Hours T.S.O.
FINMECCANICA S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY
PRODUCT SUPPORT ENGINEERING & LICENSES DEPT. 
Via  Giovanni Agusta, 520
21017  Cascina  Costa di Samarate (VA) - ITALY 
Tel.: +39 0331 225036  Fax: +39 0331 225988
We request your cooperation in filling this form,  in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all
its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in 
Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
